ARM: socfpga: dts: Add ethernet bindings for SOCFPGA
Subsystems (6)
PATCH 1/5 ARM: socfpga: dts: Add ethernet bindings for SOCFPGA
From: Dinh Nguyen <[email protected]>
Add entry for 2nd GMAC controller. Add the correct clocks for the GMAC.
--- arch/arm/boot/dts/socfpga.dtsi | 16 ++++++++++++++-- arch/arm/boot/dts/socfpga_cyclone5.dts | 16 ++++++++++++++++ arch/arm/boot/dts/socfpga_vt.dts | 8 ++++++++ 3 files changed, 38 insertions(+), 2 deletions(-)
arch/arm/boot/dts/socfpga.dtsi +14 -2
@@ -23,6 +23,7 @@ aliases { ethernet0 = &gmac0; + ethernet1 = &gmac1; serial0 = &uart0; serial1 = &uart1; timer0 = &timer0;
@@ -238,13 +239,24 @@ }; }; - gmac0: stmmac at ff700000 { + gmac0: ethernet at ff700000 { compatible = "altr,socfpga-stmmac", "snps,dwmac-3.70a", "snps,dwmac"; reg = <0xff700000 0x2000>; interrupts = <0 115 4>; interrupt-names = "macirq"; mac-address = [00 00 00 00 00 00];/* Filled in by U-Boot */ - phy-mode = "gmii"; + clocks = <&emac0_clk>; + clock-names = "stmmaceth"; + }; + + gmac1: ethernet at ff702000 { + compatible = "altr,socfpga-stmmac", "snps,dwmac-3.70a", "snps,dwmac"; + reg = <0xff702000 0x2000>; + interrupts = <0 120 4>; + interrupt-names = "macirq"; + mac-address = [00 00 00 00 00 00];/* Filled in by U-Boot */ + clocks = <&emac1_clk>; + clock-names = "stmmaceth"; }; L2: l2-cache at fffef000 {
arch/arm/boot/dts/socfpga_cyclone5.dts +16 -0
@@ -32,6 +32,13 @@ reg = <0x0 0x40000000>; /* 1GB */ }; + aliases { + /* this allow the ethaddr uboot environmnet variable contents + * to be added to the gmac1 device tree blob. + */ + ethernet0 = &gmac1; + }; + soc { clkmgr at ffd04000 { clocks {
@@ -41,6 +48,15 @@ }; }; + ethernet at ff700000 { + status = "disabled"; + }; + + ethernet at ff702000 { + phy-mode = "rgmii"; + phy-addr = <0xffffffff>; /* probe for phy addr */ + }; + timer0 at ffc08000 { clock-frequency = <100000000>; };
arch/arm/boot/dts/socfpga_vt.dts +8 -0
@@ -41,6 +41,14 @@ }; }; + ethernet at ff700000 { + phy-mode = "gmii"; + }; + + ethernet at ff702000 { + status = "disabled"; + }; + timer0 at ffc08000 { clock-frequency = <7000000>; };
Signature · 1 line
1.7.9.5
PATCH 2/5 ARM: socfpga: dts: Add gate-clock bindings
From: Dinh Nguyen <[email protected]>
Add bindings for "socfpga-gate-clk" clocks. These clocks directly feed the peripherals.
--- .../devicetree/bindings/clock/altr_socfpga.txt | 7 + arch/arm/boot/dts/socfpga.dtsi | 199 ++++++++++++++++++++ 2 files changed, 206 insertions(+)
Documentation/devicetree/bindings/clock/altr_socfpga.txt +7 -0
@@ -9,6 +9,9 @@ Required properties: "altr,socfpga-pll-clock" - for a PLL clock "altr,socfpga-perip-clock" - The peripheral clock divided from the PLL clock. + "altr,socfpga-gate-clk" - Clocks that directly feed peripherals and + can get gated. + - reg : shall be the control register offset from CLOCK_MANAGER's base for the clock. - clocks : shall be the input parent clock phandle for the clock. This is either an oscillator or a pll output.
@@ -16,3 +19,7 @@ Required properties: Optional properties: - fixed-divider : If clocks have a fixed divider value, use this property. +- clk-gate : For "socfpga-gate-clk", clk-gate contains the gating register + and the bit index. +- div-reg : For "socfpga-gate-clk", div-reg contains the divider register, bit shift, + and width.
arch/arm/boot/dts/socfpga.dtsi +199 -0
211 lines not on this page · raw message
Signature · 1 line
1.7.9.5
PATCH 2/5 ARM: socfpga: dts: Add gate-clock bindings
Hi!
Quoted 8 lines
From: Dinh Nguyen <[email protected]>
Add bindings for "socfpga-gate-clk" clocks. These clocks directly feed the peripherals.
Signed-off-by Dinh Nguyen <[email protected]>CC Arnd Bergmann <[email protected]>CC Olof Johansson <[email protected]>
Looks good to me.
Pavel
Signature · 2 lines
(english) http://www.livejournal.com/~pavelmachek (cesky, pictures) http://atrey.karlin.mff.cuni.cz/~pavel/picture/horses/blog.html
PATCH 3/5 ARM: socfpga: Add support to gate peripheral clocks
In reply to dinguyen at altera.comFrom: Dinh Nguyen <[email protected]>
Add support to gate the clocks that directly feed peripherals. For clocks with multiple parents, add the ability to determine the correct parent, and also set parents. Also add support to calculate and set the clocks' rate.
--- drivers/clk/socfpga/clk.c | 182 ++++++++++++++++++++++++++++++++++++++++++++- 1 file changed, 180 insertions(+), 2 deletions(-)
drivers/clk/socfpga/clk.c +180 -2
@@ -26,6 +26,8 @@/* Clock Manager offsets */ #define CLKMGR_CTRL 0x0#define CLKMGR_BYPASS 0x4 +#define CLKMGR_L4SRC 0x70 +#define CLKMGR_PERPLL_SRC 0xAC/* Clock bypass bits */ #define MAINPLL_BYPASS (1<<0)
@@ -41,6 +43,16 @@#define SOCFPGA_PLL_DIVF_SHIFT 3#define SOCFPGA_PLL_DIVQ_MASK 0x003F0000#define SOCFPGA_PLL_DIVQ_SHIFT 16 +#define SOCFGPA_MAX_PARENTS 3 + +#define SOCFPGA_L4_MP_CLK "l4_mp_clk" +#define SOCFPGA_L4_SP_CLK "l4_sp_clk" +#define SOCFPGA_NAND_CLK "nand_clk" +#define SOCFPGA_NAND_X_CLK "nand_x_clk" +#define SOCFPGA_MMC_CLK "mmc_clk" +#define SOCFPGA_DB_CLK "gpio_db_clk" + +#define div_mask (width) ((1 << (width)) - 1)extern void __iomem *clk_mgr_base_addr;
@@ -49,6 +61,9 @@ struct socfpga_clk {char *parent_name;char *clk_name;u32 fixed_div; +void __iomem *div_reg; +u32 width; +u32 shift; };#define to_socfpga_clk (p) container_of(p, struct socfpga_clk, hw.hw)
@@ -132,8 +147,9 @@ static __init struct clk *socfpga_clk_init(struct device_node *node, socfpga_clk->hw.hw.init = &init; -if (strcmp (clk_name,"main_pll" ) ||strcmp (clk_name,"periph_pll" ) || -strcmp (clk_name,"sdram_pll" )) { +if (strcmp (clk_name,"main_pll" ) ==0 || +strcmp (clk_name,"periph_pll" ) ==0 || +strcmp (clk_name,"sdram_pll" ) ==0 ) { socfpga_clk->hw.bit_idx =SOCFPGA_PLL_EXT_ENA ; clk_pll_ops.enable = clk_gate_ops.enable; clk_pll_ops.disable = clk_gate_ops.disable;
@@ -148,6 +164,162 @@ static __init struct clk *socfpga_clk_init(struct device_node *node,return clk; } +static u8 socfpga_clk_get_parent (struct clk_hw *hwclk) +{ +u32 l4_src; +u32 perpll_src; +u8 parent; + +if (strcmp (hwclk->init->name,SOCFPGA_L4_MP_CLK ) ==0 ) { + l4_src =readl (clk_mgr_base_addr +CLKMGR_L4SRC ); + l4_src &=0x1 ; + parent = l4_src; + }else if (strcmp (hwclk->init->name,SOCFPGA_L4_SP_CLK ) ==0 ) { + l4_src =readl (clk_mgr_base_addr +CLKMGR_L4SRC ); + l4_src = ((l4_src &0x2 ) >>1 ); + parent = l4_src; + }else { + perpll_src =readl (clk_mgr_base_addr +CLKMGR_PERPLL_SRC ); +if (strcmp (hwclk->init->name,SOCFPGA_MMC_CLK ) ==0 ) + perpll_src &=0x3 ; +else if (strcmp (hwclk->init->name,SOCFPGA_NAND_CLK ) ==0 || +strcmp (hwclk->init->name,SOCFPGA_NAND_X_CLK ) ==0 ) + perpll_src = ((perpll_src &0xC ) >>2 ); +else /*QSPI clock */ + perpll_src = ((perpll_src &0x30 ) >>4 ); + parent = perpll_src; + } + +return parent; +} + +static int socfpga_clk_set_parent (struct clk_hw *hwclk,u8 parent) +{ +u32 src_reg; + +if (strcmp (hwclk->init->name,SOCFPGA_L4_MP_CLK ) ==0 ) { + src_reg =readl (clk_mgr_base_addr +CLKMGR_L4SRC ); + src_reg &= ~0x1 ; + src_reg |= parent; +writel (src_reg, clk_mgr_base_addr +CLKMGR_L4SRC ); + }else if (strcmp (hwclk->init->name,SOCFPGA_L4_SP_CLK ) ==0 ) { + src_reg =readl (clk_mgr_base_addr +CLKMGR_L4SRC ); + src_reg &= ~0x2 ; + src_reg |= (parent <<1 ); +writel (src_reg, clk_mgr_base_addr +CLKMGR_L4SRC ); + }else { + src_reg =readl (clk_mgr_base_addr +CLKMGR_PERPLL_SRC ); +if (strcmp (hwclk->init->name,SOCFPGA_MMC_CLK ) ==0 ) { + src_reg &= ~0x3 ; + src_reg |= parent; + }else if (strcmp (hwclk->init->name,SOCFPGA_NAND_CLK ) ==0 || +strcmp (hwclk->init->name,SOCFPGA_NAND_X_CLK ) ==0 ) { + src_reg &= ~0xC ; + src_reg |= (parent <<2 ); + }else {/*QSPI clock */ + src_reg &= ~0x30 ; + src_reg |= (parent <<4 ); + } +writel (src_reg, clk_mgr_base_addr +CLKMGR_PERPLL_SRC ); + } + +return 0 ; +} + +static unsigned long socfpga_clk_recalc_rate (struct clk_hw *hwclk, +unsigned long parent_rate) +{ +struct socfpga_clk *socfpgaclk =to_socfpga_clk (hwclk); +u32 div =1 , val; + +if (socfpgaclk->fixed_div) + div = socfpgaclk->fixed_div; +else if (socfpgaclk->div_reg) { + val =readl (socfpgaclk->div_reg) >> socfpgaclk->shift; + val &=div_mask (socfpgaclk->width); +if (strcmp (hwclk->init->name,SOCFPGA_DB_CLK ) ==0 ) + div = val +1 ; +else + div = (1 << val); + } + +return parent_rate / div; +} + +static struct clk_ops gateclk_ops = { + .recalc_rate = socfpga_clk_recalc_rate, + .get_parent = socfpga_clk_get_parent, + .set_parent = socfpga_clk_set_parent, +}; + +static void __init socfpga_gate_clk_init (struct device_node *node, +const struct clk_ops *ops) +{ +u32 clk_gate[2 ]; +u32 div_reg[3 ]; +u32 fixed_div; +struct clk *clk; +struct socfpga_clk *socfpga_clk; +const char *clk_name = node->name; +const char *parent_name[SOCFGPA_MAX_PARENTS ]; +struct clk_init_data init; +int rc; +int i =0 ; + + socfpga_clk =kzalloc (sizeof (*socfpga_clk),GFP_KERNEL ); +if (WARN_ON (!socfpga_clk)) +return ; + + rc =of_property_read_u32_array (node,"clk-gate" , clk_gate,2 ); +if (rc) + clk_gate[0 ] =0 ; + + rc =of_property_read_u32 (node,"fixed-divider" , &fixed_div); +if (rc) + socfpga_clk->fixed_div =0 ; +else + socfpga_clk->fixed_div = fixed_div; + +if (clk_gate[0 ]) { + socfpga_clk->hw.reg = clk_mgr_base_addr + clk_gate[0 ]; + socfpga_clk->hw.bit_idx = clk_gate[1 ]; + + gateclk_ops.enable = clk_gate_ops.enable; + gateclk_ops.disable = clk_gate_ops.disable; + } + + rc =of_property_read_u32_array (node,"div-reg" , div_reg,3 ); +if (!rc) { + socfpga_clk->div_reg = clk_mgr_base_addr + div_reg[0 ]; + socfpga_clk->shift = div_reg[1 ]; + socfpga_clk->width = div_reg[2 ]; + }else { + socfpga_clk->div_reg =0 ; + } + +of_property_read_string (node,"clock-output-names" , &clk_name); + + init.name = clk_name; + init.ops = ops; + init.flags =0 ; +while (i <SOCFGPA_MAX_PARENTS && (parent_name[i] = +of_clk_get_parent_name (node, i)) !=NULL ) + i++; + + init.parent_names = parent_name; + init.num_parents = i; + socfpga_clk->hw.hw.init = &init; + + clk =clk_register (NULL , &socfpga_clk->hw.hw); +if (WARN_ON (IS_ERR (clk))) { +kfree (socfpga_clk); +return ; + } + rc =of_clk_add_provider (node, of_clk_src_simple_get, clk); +if (WARN_ON (rc)) +return ; +} +static void __init socfpga_pll_init (struct device_node *node) {socfpga_clk_init (node, &clk_pll_ops);
@@ -160,6 +332,12 @@ static void __init socfpga_periph_init(struct device_node *node) }CLK_OF_DECLARE (socfpga_periph,"altr,socfpga-perip-clk" , socfpga_periph_init); +static void __init socfpga_gate_init (struct device_node *node) +{ +socfpga_gate_clk_init (node, &gateclk_ops); +} +CLK_OF_DECLARE (socfpga_gate,"altr,socfpga-gate-clk" , socfpga_gate_init); +void __init socfpga_init_clocks (void ) {struct clk *clk;
Signature · 1 line
1.7.9.5
PATCH 3/5 ARM: socfpga: Add support to gate peripheral clocks
Hi!
Quoted 14 lines
Add support to gate the clocks that directly feed peripherals. For clocks with multiple parents, add the ability to determine the correct parent, and also set parents. Also add support to calculate and set the clocks' rate.
Signed-off-by Dinh Nguyen <[email protected]>CC Mike Turquette <[email protected]>CC Arnd Bergmann <[email protected]>CC Olof Johansson <[email protected]>CC Pavel Machek <[email protected]>CC <[email protected]>(quoted diff) +0
-0@@ -132,8 +147,9 @@ static __init struct clk *socfpga_clk_init(struct device_node *node,
Review static __init struct clk *socfpga_clk_init(struct device_node *node, · line 155
Quoted 10 lines
(quoted diff) +3
-2socfpga_clk->hw.hw.init = &init; - if (strcmp(clk_name, "main_pll") || strcmp(clk_name, "periph_pll") || - strcmp(clk_name, "sdram_pll")) { + if (strcmp(clk_name, "main_pll") == 0 || + strcmp(clk_name, "periph_pll") == 0 || + strcmp(clk_name, "sdram_pll") == 0) { socfpga_clk->hw.bit_idx = SOCFPGA_PLL_EXT_ENA; clk_pll_ops.enable = clk_gate_ops.enable; clk_pll_ops.disable = clk_gate_ops.disable;
Perhaps do
#define streq(a, b) (strcmp((a), (b)) == 0)
and use that to simplify the conditions?
Actually, here are suggested cleanups. Note that there are two FIXMEs -- I could not understand why the code is safe, and that the BUG_ON()s are commented on. AFAICT I got them correct, but for some reason they seem to trigger.
Thanks,
Pavel
drivers/clk/socfpga/clk.c +72 -69
@@ -24,17 +24,17 @@#include <linux/of.h> /* Clock Manager offsets */ -#define CLKMGR_CTRL 0x0 -#define CLKMGR_BYPASS 0x4 +#define CLKMGR_CTRL 0x0 +#define CLKMGR_BYPASS 0x4#define CLKMGR_L4SRC 0x70#define CLKMGR_PERPLL_SRC 0xAC/* Clock bypass bits */ -#define MAINPLL_BYPASS (1<<0) -#define SDRAMPLL_BYPASS (1<<1) -#define SDRAMPLL_SRC_BYPASS (1<<2) -#define PERPLL_BYPASS (1<<3) -#define PERPLL_SRC_BYPASS (1<<4) +#define MAINPLL_BYPASS (1<<0) +#define SDRAMPLL_BYPASS (1<<1) +#define SDRAMPLL_SRC_BYPASS (1<<2) +#define PERPLL_BYPASS (1<<3) +#define PERPLL_SRC_BYPASS (1<<4)#define SOCFPGA_PLL_BG_PWRDWN 0#define SOCFPGA_PLL_EXT_ENA 1
@@ -45,14 +45,16 @@#define SOCFPGA_PLL_DIVQ_SHIFT 16#define SOCFGPA_MAX_PARENTS 3 -#define SOCFPGA_L4_MP_CLK "l4_mp_clk" -#define SOCFPGA_L4_SP_CLK "l4_sp_clk" +#define SOCFPGA_L4_MP_CLK "l4_mp_clk" +#define SOCFPGA_L4_SP_CLK "l4_sp_clk"#define SOCFPGA_NAND_CLK "nand_clk"#define SOCFPGA_NAND_X_CLK "nand_x_clk"#define SOCFPGA_MMC_CLK "mmc_clk"#define SOCFPGA_DB_CLK "gpio_db_clk" +#define SOCFPGA_QSPI_CLK "qspi_clk"#define div_mask (width) ((1 << (width)) - 1) +#define streq (a, b) (strcmp((a), (b)) == 0)extern void __iomem *clk_mgr_base_addr;
@@ -62,8 +64,8 @@ struct socfpga_clk {char *clk_name;u32 fixed_div;void __iomem *div_reg; -u32 width; -u32 shift; +u32 width;/* only valid if div_reg != 0 */ +u32 shift;/* only valid if div_reg != 0 */ };#define to_socfpga_clk (p) container_of(p, struct socfpga_clk, hw.hw)
@@ -145,11 +147,12 @@ static __init struct clk *socfpga_clk_init(struct device_node *node, init.parent_names = &parent_name; init.num_parents =1 ; +// FIXME: assigning automatic variable ptr into malloced structure? socfpga_clk->hw.hw.init = &init; -if (strcmp (clk_name,"main_pll" ) ==0 || -strcmp (clk_name,"periph_pll" ) ==0 || -strcmp (clk_name,"sdram_pll" ) ==0 ) { +if (streq (clk_name,"main_pll" ) || +streq (clk_name,"periph_pll" ) || +streq (clk_name,"sdram_pll" )) { socfpga_clk->hw.bit_idx =SOCFPGA_PLL_EXT_ENA ; clk_pll_ops.enable = clk_gate_ops.enable; clk_pll_ops.disable = clk_gate_ops.disable;
@@ -168,61 +171,57 @@ static u8 socfpga_clk_get_parent(struct clk_hw *hwclk) {u32 l4_src;u32 perpll_src; -u8 parent; -if (strcmp (hwclk->init->name,SOCFPGA_L4_MP_CLK ) ==0 ) { +if (streq (hwclk->init->name,SOCFPGA_L4_MP_CLK )) { l4_src =readl (clk_mgr_base_addr +CLKMGR_L4SRC ); - l4_src &=0x1 ; - parent = l4_src; - }else if (strcmp (hwclk->init->name,SOCFPGA_L4_SP_CLK ) ==0 ) { +return l4_src &1 ; + } +if (streq (hwclk->init->name,SOCFPGA_L4_SP_CLK )) { l4_src =readl (clk_mgr_base_addr +CLKMGR_L4SRC ); - l4_src = ((l4_src &0x2 ) >>1 ); - parent = l4_src; - }else { - perpll_src =readl (clk_mgr_base_addr +CLKMGR_PERPLL_SRC ); -if (strcmp (hwclk->init->name,SOCFPGA_MMC_CLK ) ==0 ) - perpll_src &=0x3 ; -else if (strcmp (hwclk->init->name,SOCFPGA_NAND_CLK ) ==0 || -strcmp (hwclk->init->name,SOCFPGA_NAND_X_CLK ) ==0 ) - perpll_src = ((perpll_src &0xC ) >>2 ); -else /*QSPI clock */ - perpll_src = ((perpll_src &0x30 ) >>4 ); - parent = perpll_src; +return !!(l4_src &2 ); } + perpll_src =readl (clk_mgr_base_addr +CLKMGR_PERPLL_SRC ); +if (streq (hwclk->init->name,SOCFPGA_MMC_CLK )) +return perpll_src &3 ; +if (streq (hwclk->init->name,SOCFPGA_NAND_CLK ) || +streq (hwclk->init->name,SOCFPGA_NAND_X_CLK )) +return (perpll_src >>2 ) &3 ; + +/* else QSPI clock */ +// BUG_ON(!streq(hwclk->init->name, SOCFPGA_QSPI_CLK)); +return (perpll_src >>4 ) &3 ; +} -return parent; +static int clrsetbits (u32 adr,u32 clr,u32 set) +{ +u32 reg; + + reg =readl (adr); + reg &= ~clr; + reg |= set; +writel (reg, adr); +return 0 ; }static int socfpga_clk_set_parent (struct clk_hw *hwclk,u8 parent) { -u32 src_reg; - -if (strcmp (hwclk->init->name,SOCFPGA_L4_MP_CLK ) ==0 ) { - src_reg =readl (clk_mgr_base_addr +CLKMGR_L4SRC ); - src_reg &= ~0x1 ; - src_reg |= parent; -writel (src_reg, clk_mgr_base_addr +CLKMGR_L4SRC ); - }else if (strcmp (hwclk->init->name,SOCFPGA_L4_SP_CLK ) ==0 ) { - src_reg =readl (clk_mgr_base_addr +CLKMGR_L4SRC ); - src_reg &= ~0x2 ; - src_reg |= (parent <<1 ); -writel (src_reg, clk_mgr_base_addr +CLKMGR_L4SRC ); - }else { - src_reg =readl (clk_mgr_base_addr +CLKMGR_PERPLL_SRC ); -if (strcmp (hwclk->init->name,SOCFPGA_MMC_CLK ) ==0 ) { - src_reg &= ~0x3 ; - src_reg |= parent; - }else if (strcmp (hwclk->init->name,SOCFPGA_NAND_CLK ) ==0 || -strcmp (hwclk->init->name,SOCFPGA_NAND_X_CLK ) ==0 ) { - src_reg &= ~0xC ; - src_reg |= (parent <<2 ); - }else {/*QSPI clock */ - src_reg &= ~0x30 ; - src_reg |= (parent <<4 ); - } -writel (src_reg, clk_mgr_base_addr +CLKMGR_PERPLL_SRC ); - } +// BUG_ON(parent & ~3); + +if (streq (hwclk->init->name,SOCFPGA_L4_MP_CLK )) +return clrsetbits (clk_mgr_base_addr +CLKMGR_L4SRC ,1 , parent); +if (streq (hwclk->init->name,SOCFPGA_L4_SP_CLK )) +return clrsetbits (clk_mgr_base_addr +CLKMGR_L4SRC ,2 , parent <<1 ); +if (streq (hwclk->init->name,SOCFPGA_MMC_CLK )) +return clrsetbits (clk_mgr_base_addr +CLKMGR_PERPLL_SRC ,3 , parent); +if (streq (hwclk->init->name,SOCFPGA_NAND_CLK ) || +streq (hwclk->init->name,SOCFPGA_NAND_X_CLK )) +return clrsetbits (clk_mgr_base_addr +CLKMGR_PERPLL_SRC ,0xC , parent <<2 ); + +/* else QSPI clock */ +// BUG_ON(!streq(hwclk->init->name, SOCFPGA_QSPI_CLK)); + +clrsetbits (clk_mgr_base_addr +CLKMGR_PERPLL_SRC ,0x30 , parent <<4 );return 0 ; }
@@ -237,7 +236,7 @@ static unsigned long socfpga_clk_recalc_rate(struct clk_hw *hwclk,else if (socfpgaclk->div_reg) { val =readl (socfpgaclk->div_reg) >> socfpgaclk->shift; val &=div_mask (socfpgaclk->width); -if (strcmp (hwclk->init->name,SOCFPGA_DB_CLK ) ==0 ) +if (streq (hwclk->init->name,SOCFPGA_DB_CLK )) div = val +1 ;else div = (1 << val);
@@ -273,13 +272,6 @@ static void __init socfpga_gate_clk_init(struct device_node *node, rc =of_property_read_u32_array (node,"clk-gate" , clk_gate,2 );if (rc) clk_gate[0 ] =0 ; - - rc =of_property_read_u32 (node,"fixed-divider" , &fixed_div); -if (rc) - socfpga_clk->fixed_div =0 ; -else - socfpga_clk->fixed_div = fixed_div; -if (clk_gate[0 ]) { socfpga_clk->hw.reg = clk_mgr_base_addr + clk_gate[0 ]; socfpga_clk->hw.bit_idx = clk_gate[1 ];
@@ -288,6 +280,12 @@ static void __init socfpga_gate_clk_init(struct device_node *node, gateclk_ops.disable = clk_gate_ops.disable; } + rc =of_property_read_u32 (node,"fixed-divider" , &fixed_div); +if (rc) + socfpga_clk->fixed_div =0 ; +else + socfpga_clk->fixed_div = fixed_div; + rc =of_property_read_u32_array (node,"div-reg" , div_reg,3 );if (!rc) { socfpga_clk->div_reg = clk_mgr_base_addr + div_reg[0 ];
@@ -302,12 +300,17 @@ static void __init socfpga_gate_clk_init(struct device_node *node, init.name = clk_name; init.ops = ops; init.flags =0 ; -while (i <SOCFGPA_MAX_PARENTS && (parent_name[i] = -of_clk_get_parent_name (node, i)) !=NULL ) +while (i <SOCFGPA_MAX_PARENTS ) { +char *name =of_clk_get_parent_name (node, i); + parent_name[i] = name; +if (name ==NULL ) +break ; i++; + } init.parent_names = parent_name; init.num_parents = i; +// FIXME: assigning automatic variable ptr into malloced structure? socfpga_clk->hw.hw.init = &init; clk =clk_register (NULL , &socfpga_clk->hw.hw);
Signature · 2 lines
(english) http://www.livejournal.com/~pavelmachek (cesky, pictures) http://atrey.karlin.mff.cuni.cz/~pavel/picture/horses/blog.html
PATCH 4/5 ARM: socfpga: dts: Add support for SD/MMC
In reply to dinguyen at altera.comFrom: Dinh Nguyen <[email protected]>
Add bindings for SD/MMC for SOCFPGA.
--- .../devicetree/bindings/mmc/socfpga-dw-mshc.txt | 59 ++++++++++++++++++++ arch/arm/boot/dts/socfpga.dtsi | 11 ++++ arch/arm/boot/dts/socfpga_cyclone5.dts | 13 +++++ arch/arm/boot/dts/socfpga_vt.dts | 13 +++++ 4 files changed, 96 insertions(+) create mode 100644 Documentation/devicetree/bindings/mmc/socfpga-dw-mshc.txt
Documentation/devicetree/bindings/mmc/socfpga-dw-mshc.txt new file +59 -0
@@ -0,0 +1,59 @@ +* Altera SOCFPGA specific extensions to the Synopsis Designware Mobile + Storage Host Controller + +Required Properties: + +* compatible: should be + - "altr,socfpga-dw-mshc": for controllers with Altera SOCFPGA + specific extentions. + +* altr,dw-mshc-ciu-div: Specifies the divider value for the card interface + unit (ciu) clock. For Altera's SOCFPGA, the divider value is fixed at 4. + +* altr,dw-mshc-sdr-timing: Specifies the value of CIU clock phase shift value + in transmit mode and CIU clock phase shift value in receive mode for single + data rate mode operation. Refer notes below for the order of the cells and the + valid values. + + Notes for the sdr-timing values: + + The order of the cells should be + - First Cell: CIU clock phase shift value for RX mode, smplsel bits in + the system manager SDMMC control group. + - Second Cell: CIU clock phase shift value for TX mode, drvsel bits in + the system manager SDMMC control group. + + Valid values for SDR CIU clock timing for SOCFPGA: + - valid value for tx phase shift and rx phase shift is 0 to 7. + +Required properties for a slot: + +* bus-width: Data width for card slot. 4-bit or 8-bit data. + +Example: + + The MSHC controller node can be split into two portions, SoC specific and + board specific portions as listed below. + + dwmmc0 at ff704000 { + compatible = "altr,socfpga-dw-mshc"; + reg = <0xff704000 0x1000>; + interrupts = <0 139 4>; + #address-cells = <1>; + #size-cells = <0>; + }; + + dwmmc0 at ff704000 { + num-slots = <1>; + supports-highspeed; + broken-cd; + fifo-depth = <0x400>; + altr,dw-mshc-ciu-div = <4>; + altr,dw-mshc-sdr-timing = <0 3>; + + slot at 0 { + reg = <0>; + bus-width = <4>; + }; + }; +
arch/arm/boot/dts/socfpga.dtsi +11 -0
@@ -466,6 +466,17 @@ cache-level = <2>; }; + mmc: dwmmc0 at ff704000 { + compatible = "altr,socfpga-dw-mshc"; + reg = <0xff704000 0x1000>; + interrupts = <0 139 4>; + fifo-depth = <0x400>; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&l4_mp_clk>, <&sdmmc_clk>; + clock-names = "biu", "ciu"; + }; + /* Local timer */ timer at fffec600 { compatible = "arm,cortex-a9-twd-timer";
arch/arm/boot/dts/socfpga_cyclone5.dts +13 -0
@@ -57,6 +57,19 @@ phy-addr = <0xffffffff>; /* probe for phy addr */ }; + dwmmc0 at ff704000 { + num-slots = <1>; + supports-highspeed; + broken-cd; + altr,dw-mshc-ciu-div = <4>; + altr,dw-mshc-sdr-timing = <0 3>; + + slot at 0 { + reg = <0>; + bus-width = <4>; + }; + }; + timer0 at ffc08000 { clock-frequency = <100000000>; };
arch/arm/boot/dts/socfpga_vt.dts +13 -0
@@ -49,6 +49,19 @@ status = "disabled"; }; + dwmmc0 at ff704000 { + num-slots = <1>; + supports-highspeed; + broken-cd; + altr,dw-mshc-ciu-div = <4>; + pwr-en = <1>; + + slot at 0 { + reg = <0>; + bus-width = <4>; + }; + }; + timer0 at ffc08000 { clock-frequency = <7000000>; };
Signature · 1 line
1.7.9.5
PATCH 4/5 ARM: socfpga: dts: Add support for SD/MMC
Hi!
Quoted 9 lines
From: Dinh Nguyen <[email protected]>
Add bindings for SD/MMC for SOCFPGA.
Signed-off-by Dinh Nguyen <[email protected]>CC Arnd Bergmann <[email protected]>CC Olof Johansson <[email protected]>CC Pavel Machek <[email protected]>CC <[email protected]>
git says:
[pavel at pollux linux]$ cat /tmp/delme | git apply <stdin>:136: space before tab in indent.
altr,dw-mshc-sdr-timing = <0 3>;
<stdin>:143: new blank line at EOF.
+
warning: 2 lines add whitespace errors.
[pavel at pollux linux]$
Is this patch series expected to be enough to get MMC to work? I applied all 5 patches, and it detects the controller, but mmcblkX devices do not show up.
Synopsys Designware Multimedia Card Interface Driver dwmmc_socfpga ff704000.dwmmc0: couldn't determine pwr-en, assuming pwr-en = 0dwmmc_socfpga ff704000.dwmmc0: Using internal DMA controller. dwmmc_socfpga ff704000.dwmmc0: Version ID is 240a dwmmc_socfpga ff704000.dwmmc0: DW MMC controller at irq 171, 32 bit host data width, 1024 deep fifommc_host mmc0: Bus speed (slot 0) = 100000000Hz (slot req 400000Hz, actual 400000HZ div = 125)
...
VFS: Unable to mount root fs via NFS, trying floppy.
VFS: Cannot open root device "nfs" or unknown-block(2,0): error -6 Please append a correct "root=" boot option; here are the available partitions:
Kernel panic - not syncing: VFS: Unable to mount root fs on
unknown-block(2,0)
It should be configured in:
CONFIG_MMC_BLOCK=yCONFIG_MMC_BLOCK_MINORS=8CONFIG_MMC_BLOCK_BOUNCE=y
.
Otherwise, it looks good.
Pavel
Signature · 2 lines
(english) http://www.livejournal.com/~pavelmachek (cesky, pictures) http://atrey.karlin.mff.cuni.cz/~pavel/picture/horses/blog.html
PATCH 5/5 mmc: dw_mmc: Add support DW SD/MMC driver on SOCFPGA
In reply to dinguyen at altera.comFrom: Dinh Nguyen <[email protected]>
Add platform specific functionality for the DW SD/MMC driver for SoCFPGA. Move SDMMC_CMD_USE_HOLD_REG to dw_mmc.h so other platforms can use this define.
--- drivers/mmc/host/Kconfig | 8 +++ drivers/mmc/host/Makefile | 1 + drivers/mmc/host/dw_mmc-exynos.c | 2 - drivers/mmc/host/dw_mmc-socfpga.c | 141 +++++++++++++++++++++++++++++++++++++ drivers/mmc/host/dw_mmc.h | 1 + 5 files changed, 151 insertions(+), 2 deletions(-) create mode 100644 drivers/mmc/host/dw_mmc-socfpga.c
drivers/mmc/host/Kconfig +8 -0
@@ -556,6 +556,14 @@ config MMC_DW_EXYNOS Synopsys DesignWare Memory Card Interface driver. Select this option for platforms based on Exynos4 and Exynos5 SoC's. +config MMC_DW_SOCFPGA + tristate "SOCFPGA specific extensions for Synopsys DW Memory Card Interface" + depends on MMC_DW + select MMC_DW_PLTFM + help + This selects support for Altera SoCFPGA specific extensions to the + Synopsys DesignWare Memory Card Interface driver. + config MMC_DW_PCI tristate "Synopsys Designware MCI support on PCI bus" depends on MMC_DW && PCI
drivers/mmc/host/Makefile +1 -0
@@ -42,6 +42,7 @@ obj-$(CONFIG_SDH_BFIN) += bfin_sdh.o obj-$(CONFIG_MMC_DW) += dw_mmc.o obj-$(CONFIG_MMC_DW_PLTFM) += dw_mmc-pltfm.o obj-$(CONFIG_MMC_DW_EXYNOS) += dw_mmc-exynos.o +obj-$(CONFIG_MMC_DW_SOCFPGA) += dw_mmc-socfpga.o obj-$(CONFIG_MMC_DW_PCI) += dw_mmc-pci.o obj-$(CONFIG_MMC_SH_MMCIF) += sh_mmcif.o obj-$(CONFIG_MMC_JZ4740) += jz4740_mmc.o
drivers/mmc/host/dw_mmc-exynos.c +0 -2
@@ -31,8 +31,6 @@ SDMMC_CLKSEL_CCLK_DRIVE(y) | \ SDMMC_CLKSEL_CCLK_DIVIDER(z)) -#define SDMMC_CMD_USE_HOLD_REG BIT(29) -#define EXYNOS4210_FIXED_CIU_CLK_DIV 2#define EXYNOS4412_FIXED_CIU_CLK_DIV 4
drivers/mmc/host/dw_mmc-socfpga.c new file +141 -0
141 lines not on this page · raw message
drivers/mmc/host/dw_mmc.h +1 -0
@@ -111,6 +111,7 @@#define SDMMC_INT_ERROR 0xbfc2/* Command register defines */ #define SDMMC_CMD_START BIT(31) +#define SDMMC_CMD_USE_HOLD_REG BIT(29)#define SDMMC_CMD_CCS_EXP BIT(23)#define SDMMC_CMD_CEATA_RD BIT(22)#define SDMMC_CMD_UPD_CLK BIT(21)
Signature · 1 line
1.7.9.5
Jaehoon Chung
maintainerPATCH 5/5 mmc: dw_mmc: Add support DW SD/MMC driver on SOCFPGA
Quoted 27 lines · On 05/15/2013 07:52 AM, [email protected] wrote:
From: Dinh Nguyen <[email protected]>
Add platform specific functionality for the DW SD/MMC driver for SoCFPGA. Move
SDMMC_CMD_USE_HOLD_REGtodw_mmc.hso other platforms can use this define.Signed-off-by Dinh Nguyen <[email protected]>CC Seungwon Jeon <[email protected]>CC Jaehoon Chung <[email protected]>CC Arnd Bergmann <[email protected]>CC Olof Johansson <[email protected]>CC Pavel Machek <[email protected]>--- drivers/mmc/host/Kconfig | 8 +++ drivers/mmc/host/Makefile | 1 + drivers/mmc/host/dw_mmc-exynos.c | 2 - drivers/mmc/host/dw_mmc-socfpga.c | 141 +++++++++++++++++++++++++++++++++++++ drivers/mmc/host/dw_mmc.h | 1 + 5 files changed, 151 insertions(+), 2 deletions(-) create mode 100644 drivers/mmc/host/dw_mmc-socfpga.cdrivers/mmc/host/Kconfig +0
-0
drivers/mmc/host/Kconfig config MMC_DW_EXYNOS · line 559
Quoted 4 lines
drivers/mmc/host/Kconfig +1
-0@@ -556,6 +556,14 @@ config MMC_DW_EXYNOS Synopsys DesignWare Memory Card Interface driver. Select this option for platforms based on Exynos4 and Exynos5 SoC's. +config MMC_DW_SOCFPGA
SOCFPGA? I think good that should be changed more generic.
Quoted 55 lines
drivers/mmc/host/Kconfig +7
-0+ tristate "SOCFPGA specific extensions for Synopsys DW Memory Card Interface" + depends on MMC_DW + select MMC_DW_PLTFM + help + This selects support for Altera SoCFPGA specific extensions to the + Synopsys DesignWare Memory Card Interface driver. + config MMC_DW_PCI tristate "Synopsys Designware MCI support on PCI bus" depends on MMC_DW && PCIdrivers/mmc/host/Makefile +1
-0@@ -42,6 +42,7 @@ obj-$(CONFIG_SDH_BFIN) += bfin_sdh.o obj-$(CONFIG_MMC_DW) += dw_mmc.o obj-$(CONFIG_MMC_DW_PLTFM) += dw_mmc-pltfm.o obj-$(CONFIG_MMC_DW_EXYNOS) += dw_mmc-exynos.o +obj-$(CONFIG_MMC_DW_SOCFPGA) += dw_mmc-socfpga.o obj-$(CONFIG_MMC_DW_PCI) += dw_mmc-pci.o obj-$(CONFIG_MMC_SH_MMCIF) += sh_mmcif.o obj-$(CONFIG_MMC_JZ4740) += jz4740_mmc.odrivers/mmc/host/dw_mmc-exynos.c +0
-2@@ -31,8 +31,6 @@ SDMMC_CLKSEL_CCLK_DRIVE(y) | \ SDMMC_CLKSEL_CCLK_DIVIDER(z)) -#define SDMMC_CMD_USE_HOLD_REG BIT(29) -#define EXYNOS4210_FIXED_CIU_CLK_DIV 2#define EXYNOS4412_FIXED_CIU_CLK_DIV 4drivers/mmc/host/dw_mmc-socfpga.c new file +14
-0@@ -0,0 +1,141 @@ +/* +* Altera SoCFPGA Specific Extensions for Synopsys DW Multimedia Card Interface driver +* +* Copyright (C) 2012, Samsung Electronics Co., Ltd. +* Copyright (C) 2013 Altera Corporation +* +* This program is free software; you can redistribute it and/or modify +* it under the terms of the GNU General Public License as published by +* the Free Software Foundation; either version 2 of the License, or +* (at your option) any later version. +* +* Taken from dw_mmc_exynos.c +*/ +#include <linux/clk.h>
drivers/mmc/host/dw_mmc-socfpga.c line 24
Quoted 10 lines
drivers/mmc/host/dw_mmc-socfpga.c new file +10
-0+#include <linux/mmc/host.h> +#include <linux/mmc/dw_mmc.h> +#include <linux/module.h> +#include <linux/of.h> +#include <linux/platform_device.h> + +#include "dw_mmc.h" +#include "dw_mmc-pltfm.h" + +#define SYSMGR_SDMMCGRP_CTRL_OFFSET 0x108
Is it vendor specific register offset?
drivers/mmc/host/dw_mmc-socfpga.c line 27
Quoted 3 lines
drivers/mmc/host/dw_mmc-socfpga.c new file +3
-0+#define DRV_CLK_PHASE_SHIFT_SEL_MASK 0x7 +#define SYSMGR_SDMMC_CTRL_SET (smplsel, drvsel) \ + ((((drvsel) << 0) & 0x7) | (((smplsel) << 3) & 0x38))
Change more readable. ((drvsel & 0x7) << 0 | (smplsel & 0x7) << 3)?
Quoted 20 lines
drivers/mmc/host/dw_mmc-socfpga.c new file +20
-0+ +extern void __iomem *sys_manager_base_addr; + +/* SOCFPGA implementation specific driver private data */ +struct dw_mci_socfpga_priv_data { +u8 ciu_div; +u32 hs_timing; +}; + +static int dw_mci_socfpga_priv_init (struct dw_mci *host) +{ +struct dw_mci_socfpga_priv_data *priv; +struct device *dev = host->dev; +int pwr_en; + + priv =devm_kzalloc (host->dev,sizeof (*priv),GFP_KERNEL ); +if (!priv) { +dev_err (host->dev,"mem alloc failed for private data\n" ); +return -ENOMEM ; + }
drivers/mmc/host/dw_mmc-socfpga.c line 57
Quoted 10 lines
drivers/mmc/host/dw_mmc-socfpga.c new file +10
-0+ + host->priv = priv; + +if (of_property_read_u32 (dev->of_node,"pwr-en" , &pwr_en)) { +dev_info (dev,"couldn't determine pwr-en, assuming pwr-en = 0\n" ); + pwr_en =0 ; + } + +/* Set PWREN bit */ +mci_writel (host,PWREN , pwr_en);
What is this setting? In dw-mmc.c, PWREN register should be set.
drivers/mmc/host/dw_mmc-socfpga.c line 69
Quoted 12 lines
drivers/mmc/host/dw_mmc-socfpga.c new file +12
-0+ +return 0 ; +} + +static int dw_mci_socfpga_setup_clock (struct dw_mci *host) +{ +struct dw_mci_socfpga_priv_data *priv = host->priv; + +clk_disable (host->ciu_clk); +writel (priv->hs_timing, sys_manager_base_addr + +SYSMGR_SDMMCGRP_CTRL_OFFSET ); +clk_enable (host->ciu_clk);
Why do you use the clk_disable/enable at this point?
drivers/mmc/host/dw_mmc-socfpga.c line 71
Quoted 2 lines
drivers/mmc/host/dw_mmc-socfpga.c new file +2
-0+ + host->bus_hz /= priv->ciu_div;
Didn't consider the "divide by zero"?
Quoted 83 lines
drivers/mmc/host/dw_mmc-socfpga.c new file +70
-0+return 0 ; +} + +static void dw_mci_socfpga_prepare_command (struct dw_mci *host,u32 *cmdr) +{ +struct dw_mci_socfpga_priv_data *priv = host->priv; + +if (priv->hs_timing &DRV_CLK_PHASE_SHIFT_SEL_MASK ) + *cmdr |=SDMMC_CMD_USE_HOLD_REG ; +} + +static int dw_mci_socfpga_parse_dt (struct dw_mci *host) +{ +struct dw_mci_socfpga_priv_data *priv = host->priv; +struct device_node *np = host->dev->of_node; +u32 timing[2 ]; +u32 div =0 ; +int ret; + +of_property_read_u32 (np,"altr,dw-mshc-ciu-div" , &div); + priv->ciu_div = div; + + ret =of_property_read_u32_array (np, +"altr,dw-mshc-sdr-timing" , timing,2 ); +if (ret) +return ret; + + priv->hs_timing =SYSMGR_SDMMC_CTRL_SET (timing[0 ], timing[1 ]); +return 0 ; +} + +static const struct dw_mci_drv_data socfpga_drv_data = { + .init = dw_mci_socfpga_priv_init, + .setup_clock = dw_mci_socfpga_setup_clock, + .prepare_command = dw_mci_socfpga_prepare_command, + .parse_dt = dw_mci_socfpga_parse_dt, +}; + +static const struct of_device_id dw_mci_socfpga_match[] = { + { .compatible ="altr,socfpga-dw-mshc" , + .data = &socfpga_drv_data, }, + {}, +}; +MODULE_DEVICE_TABLE (of, dw_mci_socfpga_match); + +int dw_mci_socfpga_probe (struct platform_device *pdev) +{ +const struct dw_mci_drv_data *drv_data; +const struct of_device_id *match; + + match =of_match_node (dw_mci_socfpga_match, pdev->dev.of_node); + drv_data = match->data; +return dw_mci_pltfm_register (pdev, drv_data); +} + +static struct platform_driver dw_mci_socfpga_pltfm_driver = { + .probe = dw_mci_socfpga_probe, + .remove =__exit_p (dw_mci_pltfm_remove), + .driver = { + .name ="dwmmc_socfpga" , + .of_match_table =of_match_ptr (dw_mci_socfpga_match), + .pm = &dw_mci_pltfm_pmops, + }, +}; + +module_platform_driver (dw_mci_socfpga_pltfm_driver); + +MODULE_DESCRIPTION ("Altera SOCFPGA Specific DW-MSHC Driver Extension" ); +MODULE_LICENSE ("GPL v2" ); +MODULE_ALIAS ("platform:dwmmc-socfpga" );drivers/mmc/host/dw_mmc.h +1
-0@@ -111,6 +111,7 @@#define SDMMC_INT_ERROR 0xbfc2/* Command register defines */ #define SDMMC_CMD_START BIT(31) +#define SDMMC_CMD_USE_HOLD_REG BIT(29)#define SDMMC_CMD_CCS_EXP BIT(23)#define SDMMC_CMD_CEATA_RD BIT(22)#define SDMMC_CMD_UPD_CLK BIT(21)
PATCH 5/5 mmc: dw_mmc: Add support DW SD/MMC driver on SOCFPGA
Hi,
Quoted 31 lines · Jaehoon Chung
Quoted 30 lines · dinguyen at altera.com
From: Dinh Nguyen <[email protected]>
Add platform specific functionality for the DW SD/MMC driver for SoCFPGA. Move
SDMMC_CMD_USE_HOLD_REGtodw_mmc.hso other platforms can use this define.Signed-off-by Dinh Nguyen <[email protected]>CC Seungwon Jeon <[email protected]>CC Jaehoon Chung <[email protected]>CC Arnd Bergmann <[email protected]>CC Olof Johansson <[email protected]>CC Pavel Machek <[email protected]>CC linux-mmc at vger.kernel.org--- drivers/mmc/host/Kconfig | 8 +++ drivers/mmc/host/Makefile | 1 + drivers/mmc/host/dw_mmc-exynos.c | 2 - drivers/mmc/host/dw_mmc-socfpga.c | 141 +++++++++++++++++++++++++++++++++++++ drivers/mmc/host/dw_mmc.h | 1 + 5 files changed, 151 insertions(+), 2 deletions(-) create mode 100644 drivers/mmc/host/dw_mmc-socfpga.cdrivers/mmc/host/Kconfig +0
-0@@ -556,6 +556,14 @@ config MMC_DW_EXYNOS Synopsys DesignWare Memory Card Interface driver. Select this option for platforms based on Exynos4 and Exynos5 SoC's.
Quoted 2 lines
drivers/mmc/host/Kconfig config MMC_DW_EXYNOS · line 559
Quoted 1 line
drivers/mmc/host/Kconfig +1
-0+config MMC_DW_SOCFPGASOCFPGA? I think good that should be changed more generic.
Not sure what you mean? SOCFPGA is the name of new ARM SOCs from Altera.
Quoted 93 lines
Quoted 55 lines
drivers/mmc/host/Kconfig +7
-0+ tristate "SOCFPGA specific extensions for Synopsys DW Memory Card Interface" + depends on MMC_DW + select MMC_DW_PLTFM + help + This selects support for Altera SoCFPGA specific extensions to the + Synopsys DesignWare Memory Card Interface driver. + config MMC_DW_PCI tristate "Synopsys Designware MCI support on PCI bus" depends on MMC_DW && PCIdrivers/mmc/host/Makefile +1
-0@@ -42,6 +42,7 @@ obj-$(CONFIG_SDH_BFIN) += bfin_sdh.o obj-$(CONFIG_MMC_DW) += dw_mmc.o obj-$(CONFIG_MMC_DW_PLTFM) += dw_mmc-pltfm.o obj-$(CONFIG_MMC_DW_EXYNOS) += dw_mmc-exynos.o +obj-$(CONFIG_MMC_DW_SOCFPGA) += dw_mmc-socfpga.o obj-$(CONFIG_MMC_DW_PCI) += dw_mmc-pci.o obj-$(CONFIG_MMC_SH_MMCIF) += sh_mmcif.o obj-$(CONFIG_MMC_JZ4740) += jz4740_mmc.odrivers/mmc/host/dw_mmc-exynos.c +0
-2@@ -31,8 +31,6 @@ SDMMC_CLKSEL_CCLK_DRIVE(y) | \ SDMMC_CLKSEL_CCLK_DIVIDER(z)) -#define SDMMC_CMD_USE_HOLD_REG BIT(29) -#define EXYNOS4210_FIXED_CIU_CLK_DIV 2#define EXYNOS4412_FIXED_CIU_CLK_DIV 4drivers/mmc/host/dw_mmc-socfpga.c new file +14
-0@@ -0,0 +1,141 @@ +/* +* Altera SoCFPGA Specific Extensions for Synopsys DW Multimedia Card Interface driver +* +* Copyright (C) 2012, Samsung Electronics Co., Ltd. +* Copyright (C) 2013 Altera Corporation +* +* This program is free software; you can redistribute it and/or modify +* it under the terms of the GNU General Public License as published by +* the Free Software Foundation; either version 2 of the License, or +* (at your option) any later version. +* +* Taken from dw_mmc_exynos.c +*/ +#include <linux/clk.h> drivers/mmc/host/dw_mmc-socfpga.c line 24
Quoted 10 lines
drivers/mmc/host/dw_mmc-socfpga.c new file +10
-0+#include <linux/mmc/host.h> +#include <linux/mmc/dw_mmc.h> +#include <linux/module.h> +#include <linux/of.h> +#include <linux/platform_device.h> + +#include "dw_mmc.h" +#include "dw_mmc-pltfm.h" + +#define SYSMGR_SDMMCGRP_CTRL_OFFSET 0x108Is it vendor specific register offset?
drivers/mmc/host/dw_mmc-socfpga.c line 27
Quoted 3 lines
drivers/mmc/host/dw_mmc-socfpga.c new file +3
-0+#define DRV_CLK_PHASE_SHIFT_SEL_MASK 0x7 +#define SYSMGR_SDMMC_CTRL_SET (smplsel, drvsel) \ + ((((drvsel) << 0) & 0x7) | (((smplsel) << 3) & 0x38))Change more readable. ((drvsel &
0x7) << 0 | (smplsel &0x7) << 3)?Quoted 23 lines
drivers/mmc/host/dw_mmc-socfpga.c new file +23
-0+ +extern void __iomem *sys_manager_base_addr; + +/* SOCFPGA implementation specific driver private data */ +struct dw_mci_socfpga_priv_data { +u8 ciu_div; +u32 hs_timing; +}; + +static int dw_mci_socfpga_priv_init (struct dw_mci *host) +{ +struct dw_mci_socfpga_priv_data *priv; +struct device *dev = host->dev; +int pwr_en; + + priv =devm_kzalloc (host->dev,sizeof (*priv),GFP_KERNEL ); +if (!priv) { +dev_err (host->dev,"mem alloc failed for private data\n" ); +return -ENOMEM ; + } + + host->priv = priv; +
Quoted 8 lines
drivers/mmc/host/dw_mmc-socfpga.c line 57
Quoted 7 lines
drivers/mmc/host/dw_mmc-socfpga.c new file +7
-0+if (of_property_read_u32 (dev->of_node,"pwr-en" , &pwr_en)) { +dev_info (dev,"couldn't determine pwr-en, assuming pwr-en = 0\n" ); + pwr_en =0 ; + } + +/* Set PWREN bit */ +mci_writel (host,PWREN , pwr_en);What is this setting? In
dw-mmc.c, PWREN register should be set.
Ah..it was there before 3.9...I will adjust accordingly.
Quoted 5 lines
Quoted 5 lines
drivers/mmc/host/dw_mmc-socfpga.c new file +5
-0+ +return 0 ; +} + +static int dw_mci_socfpga_setup_clock (struct dw_mci *host)
Quoted 8 lines
drivers/mmc/host/dw_mmc-socfpga.c line 69
Quoted 7 lines
drivers/mmc/host/dw_mmc-socfpga.c new file +7
-0+{ +struct dw_mci_socfpga_priv_data *priv = host->priv; + +clk_disable (host->ciu_clk); +writel (priv->hs_timing, sys_manager_base_addr + +SYSMGR_SDMMCGRP_CTRL_OFFSET ); +clk_enable (host->ciu_clk);Why do you use the clk_disable/enable at this point?
Our implementation of the controller requires us to disable the clock when we adjust the timing parameter.
Quoted 3 lines
drivers/mmc/host/dw_mmc-socfpga.c line 71
Quoted 2 lines
drivers/mmc/host/dw_mmc-socfpga.c new file +2
-0+ + host->bus_hz /= priv->ciu_div;Didn't consider the "divide by zero"?
Will fix..
Thanks alot for the review.
Dinh
Quoted 84 lines
Quoted 83 lines
drivers/mmc/host/dw_mmc-socfpga.c new file +70
-0+return 0 ; +} + +static void dw_mci_socfpga_prepare_command (struct dw_mci *host,u32 *cmdr) +{ +struct dw_mci_socfpga_priv_data *priv = host->priv; + +if (priv->hs_timing &DRV_CLK_PHASE_SHIFT_SEL_MASK ) + *cmdr |=SDMMC_CMD_USE_HOLD_REG ; +} + +static int dw_mci_socfpga_parse_dt (struct dw_mci *host) +{ +struct dw_mci_socfpga_priv_data *priv = host->priv; +struct device_node *np = host->dev->of_node; +u32 timing[2 ]; +u32 div =0 ; +int ret; + +of_property_read_u32 (np,"altr,dw-mshc-ciu-div" , &div); + priv->ciu_div = div; + + ret =of_property_read_u32_array (np, +"altr,dw-mshc-sdr-timing" , timing,2 ); +if (ret) +return ret; + + priv->hs_timing =SYSMGR_SDMMC_CTRL_SET (timing[0 ], timing[1 ]); +return 0 ; +} + +static const struct dw_mci_drv_data socfpga_drv_data = { + .init = dw_mci_socfpga_priv_init, + .setup_clock = dw_mci_socfpga_setup_clock, + .prepare_command = dw_mci_socfpga_prepare_command, + .parse_dt = dw_mci_socfpga_parse_dt, +}; + +static const struct of_device_id dw_mci_socfpga_match[] = { + { .compatible ="altr,socfpga-dw-mshc" , + .data = &socfpga_drv_data, }, + {}, +}; +MODULE_DEVICE_TABLE (of, dw_mci_socfpga_match); + +int dw_mci_socfpga_probe (struct platform_device *pdev) +{ +const struct dw_mci_drv_data *drv_data; +const struct of_device_id *match; + + match =of_match_node (dw_mci_socfpga_match, pdev->dev.of_node); + drv_data = match->data; +return dw_mci_pltfm_register (pdev, drv_data); +} + +static struct platform_driver dw_mci_socfpga_pltfm_driver = { + .probe = dw_mci_socfpga_probe, + .remove =__exit_p (dw_mci_pltfm_remove), + .driver = { + .name ="dwmmc_socfpga" , + .of_match_table =of_match_ptr (dw_mci_socfpga_match), + .pm = &dw_mci_pltfm_pmops, + }, +}; + +module_platform_driver (dw_mci_socfpga_pltfm_driver); + +MODULE_DESCRIPTION ("Altera SOCFPGA Specific DW-MSHC Driver Extension" ); +MODULE_LICENSE ("GPL v2" ); +MODULE_ALIAS ("platform:dwmmc-socfpga" );drivers/mmc/host/dw_mmc.h +1
-0@@ -111,6 +111,7 @@#define SDMMC_INT_ERROR 0xbfc2/* Command register defines */ #define SDMMC_CMD_START BIT(31) +#define SDMMC_CMD_USE_HOLD_REG BIT(29)#define SDMMC_CMD_CCS_EXP BIT(23)#define SDMMC_CMD_CEATA_RD BIT(22)#define SDMMC_CMD_UPD_CLK BIT(21)
PATCH 5/5 mmc: dw_mmc: Add support DW SD/MMC driver on SOCFPGA
In reply to dinguyen at altera.comdrivers/mmc/host/dw_mmc-socfpga.c line 29
Quoted 7 lines · dinguyen at altera.com
drivers/mmc/host/dw_mmc-socfpga.c new file +7
-0+ +#define SYSMGR_SDMMCGRP_CTRL_OFFSET 0x108 +#define DRV_CLK_PHASE_SHIFT_SEL_MASK 0x7 +#define SYSMGR_SDMMC_CTRL_SET (smplsel, drvsel) \ + ((((drvsel) << 0) & 0x7) | (((smplsel) << 3) & 0x38)) + +extern void __iomem *sys_manager_base_addr;
This is not acceptable, you cannot just reference external symbols from one driver in another, without a proper interface.
Please explain what the functionality is that you need here, then we can help you find the proper interface. My guess is that you need either the functionality provided by drivers/reset/ or drivers/mfd/syscon.c.
drivers/mmc/host/dw_mmc-socfpga.c line 57
Quoted 7 lines
drivers/mmc/host/dw_mmc-socfpga.c new file +7
-0+if (of_property_read_u32 (dev->of_node,"pwr-en" , &pwr_en)) { +dev_info (dev,"couldn't determine pwr-en, assuming pwr-en = 0\n" ); + pwr_en =0 ; + } + +/* Set PWREN bit */ +mci_writel (host,PWREN , pwr_en);
If you add new properties, you have to document them in Documentations/devicetree/bindings/*.
What is the requirement for this property? Is there no way to automatically power the card on/off using the normal dw_mci_set_ios function?
The rest of this patch looks ok to me.
Arnd
PATCH 5/5 mmc: dw_mmc: Add support DW SD/MMC driver on SOCFPGA
Hi Arnd,
Thanks for the review.
Quoted 12 lines · Arnd Bergmann
drivers/mmc/host/dw_mmc-socfpga.c line 29
Quoted 7 lines · dinguyen at altera.com
drivers/mmc/host/dw_mmc-socfpga.c new file +7
-0+ +#define SYSMGR_SDMMCGRP_CTRL_OFFSET 0x108 +#define DRV_CLK_PHASE_SHIFT_SEL_MASK 0x7 +#define SYSMGR_SDMMC_CTRL_SET (smplsel, drvsel) \ + ((((drvsel) << 0) & 0x7) | (((smplsel) << 3) & 0x38)) + +extern void __iomem *sys_manager_base_addr;This is not acceptable, you cannot just reference external symbols from one driver in another, without a proper interface.
Quoted 4 lines
Please explain what the functionality is that you need here, then we can help you find the proper interface. My guess is that you need either the functionality provided by
drivers/reset/ordrivers/mfd/syscon.c.
Our implementation has the timing controls for the SD/MMC controller in another custom IP block(system manager). sys_manager_base_addr was mapped in mach-socfpga/socfpga.c. I saw the same approach with drivers/clk(clk_mgr_base_addr), so I thought it would be ok with this driver. Please advise on another way to do this...
Quoted 9 lines
drivers/mmc/host/dw_mmc-socfpga.c line 57
Quoted 8 lines
drivers/mmc/host/dw_mmc-socfpga.c new file +7
-0+if (of_property_read_u32 (dev->of_node,"pwr-en" , &pwr_en)) { +dev_info (dev,"couldn't determine pwr-en, assuming pwr-en = 0\n" ); + pwr_en =0 ; + } + +/* Set PWREN bit */ +mci_writel (host,PWREN , pwr_en);
Quoted 6 lines
If you add new properties, you have to document them in Documentations/devicetree/bindings/*.
What is the requirement for this property? Is there no way to automatically power the card on/off using the normal
dw_mci_set_iosfunction?
Apologies...it wasn't there in 3.8. I will fix...
Thanks,
Dinh
Quoted 5 lines
The rest of this patch looks ok to me.
Arnd
PATCH 5/5 mmc: dw_mmc: Add support DW SD/MMC driver on SOCFPGA
Quoted 18 lines · On Wednesday 15 May 2013 11:40:12 Dinh Nguyen wrote:
Quoted 12 lines · Arnd Bergmann
drivers/mmc/host/dw_mmc-socfpga.c line 29
Quoted 7 lines · On Wednesday 15 May 2013, [email protected] wrote:
drivers/mmc/host/dw_mmc-socfpga.c new file +7
-0+ +#define SYSMGR_SDMMCGRP_CTRL_OFFSET 0x108 +#define DRV_CLK_PHASE_SHIFT_SEL_MASK 0x7 +#define SYSMGR_SDMMC_CTRL_SET (smplsel, drvsel) \ + ((((drvsel) << 0) & 0x7) | (((smplsel) << 3) & 0x38)) + +extern void __iomem *sys_manager_base_addr;This is not acceptable, you cannot just reference external symbols from one driver in another, without a proper interface.
Quoted 4 lines
Please explain what the functionality is that you need here, then we can help you find the proper interface. My guess is that you need either the functionality provided by
drivers/reset/ordrivers/mfd/syscon.c.
Quoted 5 lines
Our implementation has the timing controls for the SD/MMC controller in another custom IP block(system manager).
sys_manager_base_addrwas mapped inmach-socfpga/socfpga.c. I saw the same approach with drivers/clk(clk_mgr_base_addr), so I thought it would be ok with this driver. Please advise on another way to do this...
The clock code is tied more more closely to the platform code, so I was turning a blind eye on that one, under the assumption that it was only used there.
Arnd
PATCH 5/5 mmc: dw_mmc: Add support DW SD/MMC driver on SOCFPGA
Hi Arnd,
Quoted 25 lines · Arnd Bergmann
Quoted 18 lines · On Wednesday 15 May 2013 11:40:12 Dinh Nguyen wrote:
Quoted 12 lines · Arnd Bergmann
drivers/mmc/host/dw_mmc-socfpga.c line 29
Quoted 7 lines · dinguyen at altera.com
drivers/mmc/host/dw_mmc-socfpga.c new file +7
-0+ +#define SYSMGR_SDMMCGRP_CTRL_OFFSET 0x108 +#define DRV_CLK_PHASE_SHIFT_SEL_MASK 0x7 +#define SYSMGR_SDMMC_CTRL_SET (smplsel, drvsel) \ + ((((drvsel) << 0) & 0x7) | (((smplsel) << 3) & 0x38)) + +extern void __iomem *sys_manager_base_addr;This is not acceptable, you cannot just reference external symbols from one driver in another, without a proper interface.
Quoted 4 lines
Please explain what the functionality is that you need here, then we can help you find the proper interface. My guess is that you need either the functionality provided by
drivers/reset/ordrivers/mfd/syscon.c.Quoted 5 lines
Our implementation has the timing controls for the SD/MMC controller in another custom IP block(system manager).
sys_manager_base_addrwas mapped inmach-socfpga/socfpga.c. I saw the same approach with drivers/clk(clk_mgr_base_addr), so I thought it would be ok with this driver. Please advise on another way to do this...
Quoted 3 lines
The clock code is tied more more closely to the platform code, so I was turning a blind eye on that one, under the assumption that it was only used there.
I think I can use the syscon interface for this. Thanks for the pointer. I kinda thought that these dw_mmc-<platform> is platform specific enough, but I will go the syscon route.
Dinh
Quoted 3 lines
Arnd
PATCH 1/5 ARM: socfpga: dts: Add ethernet bindings for SOCFPGA
In reply to dinguyen at altera.comQuoted 9 lines · dinguyen at altera.com
From: Dinh Nguyen <[email protected]>
Add entry for 2nd GMAC controller. Add the correct clocks for the GMAC.
Signed-off-by Dinh Nguyen <[email protected]>CC Arnd Bergmann <[email protected]>CC Olof Johansson <[email protected]>CC Pavel Machek <[email protected]>CC <[email protected]>
Looks good.
...but, this patch is not enough to get ethernet to work with 3.10-rc1, right? I hoped that applying 1-3 of the series would get me ethernet, but no :-(.
Thanks,
Pavel
Signature · 2 lines
(english) http://www.livejournal.com/~pavelmachek (cesky, pictures) http://atrey.karlin.mff.cuni.cz/~pavel/picture/horses/blog.html
PATCH 1/5 ARM: socfpga: dts: Add ethernet bindings for SOCFPGA
Hi Pavel,
Thanks for the review...
Quoted 11 lines · Pavel Machek
Quoted 9 lines · dinguyen at altera.com
From: Dinh Nguyen <[email protected]>
Add entry for 2nd GMAC controller. Add the correct clocks for the GMAC.
Signed-off-by Dinh Nguyen <[email protected]>CC Arnd Bergmann <[email protected]>CC Olof Johansson <[email protected]>CC Pavel Machek <[email protected]>CC <[email protected]>
Quoted 7 lines
Looks good.
Reviewed-by Pavel Machek <[email protected]>...but, this patch is not enough to get ethernet to work with 3.10-rc1, right? I hoped that applying 1-3 of the series would get me ethernet, but no :-(.
Yes, this fixes a build error for socfpga_defconfig in 3.10-rc1. I'll send a patch to enable ethernet after these patches are accepted.
Dinh
Quoted 4 lines
Thanks,
Pavel
PATCH 1/5 ARM: socfpga: dts: Add ethernet bindings for SOCFPGA
In reply to dinguyen at altera.comarch/arm/boot/dts/socfpga_vt.dts line 50
Quoted 9 lines · dinguyen at altera.com
};arch/arm/boot/dts/socfpga_vt.dts +7
-0+ ethernet at ff700000 { + phy-mode = "gmii"; + }; + + ethernet at ff702000 { + status = "disabled"; + };
By convention, please mark the controllers as "disabled" in the main .dtsi file and only enable them in the board specific files when used, rather than the other way round.
Arnd
PATCH 1/5 ARM: socfpga: dts: Add ethernet bindings for SOCFPGA
Hi Arnd,
Quoted 11 lines · Arnd Bergmann
arch/arm/boot/dts/socfpga_vt.dts line 50
Quoted 9 lines · dinguyen at altera.com
};arch/arm/boot/dts/socfpga_vt.dts +7
-0+ ethernet at ff700000 { + phy-mode = "gmii"; + }; + + ethernet at ff702000 { + status = "disabled"; + };
Quoted 3 lines
By convention, please mark the controllers as "disabled" in the main .dtsi file and only enable them in the board specific files when used, rather than the other way round.
Thanks for the review. Will fix.
Dinh
Quoted 3 lines
Arnd