Skip to contentSkip to conversation

ARM: at91: dt: add USBA support

PATCH Superseded Jean-Christophe PLAGNIOL-VILLARD 2 participants 9 messages May 17, 2013 – May 20, 2013

Subsystems (5)

v3 of 4 Superseded Latest is v4 →

lore
Share & tools
lore
#0 lore raw

v3 cover ARM: at91: dt: add USBA support

HI,

v3:
rebase againt 3.10-rc1 + dt macro cleanup

This patch serie finish to add the usb device support to dt for at91 with the usba support present on the last at91 generation since sam9g45

The following changes since commit b3f442b0eedbc20b5ce3f4a96530588d14901199:

ARM: at91: udpate defconfigs (2013-05-17 15:05:08 +0200)

are available in the git repository at:

git://github.com/at91linux/linux-at91.git j/for-3.11-usba

for you to fetch changes up to f24c9792c29803420a7bf7204223ef028191d449:

ARM: at91: sam9m10g45ek add udc DT support (2013-05-17 22:05:46 +0800)

----------------------------------------------------------------
Jean-Christophe PLAGNIOL-VILLARD (5):
usb: add Atmel USBA UDC DT support
ARM: at91: sam9x5 add udc DT support
ARM: at91: sam9x5ek add udc DT support
ARM: at91: sam9g45 add udc DT support
ARM: at91: sam9m10g45ek add udc DT support

 Documentation/devicetree/bindings/usb/atmel-usb.txt |   82 +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
 arch/arm/boot/dts/at91sam9g45.dtsi                  |   62 ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
 arch/arm/boot/dts/at91sam9m10g45ek.dts              |    5 +++++
 arch/arm/boot/dts/at91sam9x5.dtsi                   |   62 ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
 arch/arm/boot/dts/at91sam9x5ek.dtsi                 |    5 +++++
 arch/arm/mach-at91/at91sam9g45.c                    |    2 ++
 arch/arm/mach-at91/at91sam9x5.c                     |    2 ++
 drivers/usb/gadget/Kconfig                          |    2 +-
 drivers/usb/gadget/atmel_usba_udc.c                 |  214 ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++----------------------------------------------------
 drivers/usb/gadget/atmel_usba_udc.h                 |    1 +
 10 files changed, 382 insertions(+), 55 deletions(-)

Best Regards,
J.

#1 lore raw

PATCH v3 1/5 usb: add Atmel USBA UDC DT support

Allow to compile the driver all the time if AT91 enabled.

Cc Nicolas Ferre <[email protected]>
Cc linux-usb at vger.kernel.org
---
 .../devicetree/bindings/usb/atmel-usb.txt          |   82 ++++++++
 drivers/usb/gadget/Kconfig                         |    2 +-
 drivers/usb/gadget/atmel_usba_udc.c                |  214 +++++++++++++++-----
 drivers/usb/gadget/atmel_usba_udc.h                |    1 +
 4 files changed, 244 insertions(+), 55 deletions(-)
Documentation/devicetree/bindings/usb/atmel-usb.txt +82 -0
index 60bd215..878556b2 100644
@@ -47,3 +47,85 @@ usb1: gadget at fffa4000 {
 	interrupts = <10 4>;
 	atmel,vbus-gpio = <&pioC 5 0>;
 };
+
+Atmel High-Speed USB device controller
+
+Required properties:
+ - compatible: Should be "atmel,at91sam9rl-udc"
+ - reg: Address and length of the register set for the device
+ - interrupts: Should contain macb interrupt
+ - ep childnode: To specifiy the number of endpoints and their properties.
+
+Optional properties:
+ - atmel,vbus-gpio: If present, specifies a gpio that needs to be
+   activated for the bus to be powered.
+
+Required child node properties:
+ - name: Name of the endpoint.
+ - reg: Num of the endpoint.
+ - atmel,fifo-size: Size of the fifo.
+ - atmel,nb-banks: Number of banks.
+ - atmel,can-dma: Boolean to specify if the endpoint support DMA.
+ - atmel,can-isoc: Boolean to specify if the endpoint support ISOC.
+
+usb2: gadget at fff78000 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	compatible = "atmel,at91sam9rl-udc";
+	reg = <0x00600000 0x80000
+	       0xfff78000 0x400>;
+	interrupts = <27 4>;
+	atmel,vbus-gpio = <&pioB 19 0>;
+
+	ep0 {
+		reg = <0>;
+		atmel,fifo-size = <64>;
+		atmel,nb-banks = <1>;
+	};
+
+	ep1 {
+		reg = <1>;
+		atmel,fifo-size = <1024>;
+		atmel,nb-banks = <2>;
+		atmel,can-dma;
+		atmel,can-isoc;
+	};
+
+	ep2 {
+		reg = <2>;
+		atmel,fifo-size = <1024>;
+		atmel,nb-banks = <2>;
+		atmel,can-dma;
+		atmel,can-isoc;
+	};
+
+	ep3 {
+		reg = <3>;
+		atmel,fifo-size = <1024>;
+		atmel,nb-banks = <3>;
+		atmel,can-dma;
+	};
+
+	ep4 {
+		reg = <4>;
+		atmel,fifo-size = <1024>;
+		atmel,nb-banks = <3>;
+		atmel,can-dma;
+	};
+
+	ep5 {
+		reg = <5>;
+		atmel,fifo-size = <1024>;
+		atmel,nb-banks = <3>;
+		atmel,can-dma;
+		atmel,can-isoc;
+	};
+
+	ep6 {
+		reg = <6>;
+		atmel,fifo-size = <1024>;
+		atmel,nb-banks = <3>;
+		atmel,can-dma;
+		atmel,can-isoc;
+	};
+};
drivers/usb/gadget/Kconfig +1 -1
index 83300d9..5e47d50 100644
@@ -156,7 +156,7 @@ config USB_LPC32XX
 
 config USB_ATMEL_USBA
 	tristate "Atmel USBA"
-	depends on AVR32 || ARCH_AT91SAM9RL || ARCH_AT91SAM9G45
+	depends on AVR32 || ARCH_AT91
 	help
 	  USBA is the integrated high-speed USB Device controller on
 	  the AT32AP700x, some AT91SAM9 and AT91CAP9 processors from Atmel.
drivers/usb/gadget/atmel_usba_udc.c +160 -54

290 lines not on this page · raw message

drivers/usb/gadget/atmel_usba_udc.h +1 -0
index d65a618..6999a26 100644
@@ -317,6 +317,7 @@ struct usba_udc {
 	int irq;
 	int vbus_pin;
 	int vbus_pin_inverted;
+	int num_ep;
 	struct clk *pclk;
 	struct clk *hclk;
 
Signature · 1 line
1.7.10.4
#2 lore raw

PATCH v3 2/5 ARM: at91: sam9x5 add udc DT support

---
 arch/arm/boot/dts/at91sam9x5.dtsi |   62 +++++++++++++++++++++++++++++++++++++
 arch/arm/mach-at91/at91sam9x5.c   |    2 ++
 2 files changed, 64 insertions(+)
arch/arm/boot/dts/at91sam9x5.dtsi +62 -0
index af91599..01a815d 100644
@@ -645,6 +645,68 @@
 				status = "disabled";
 			};
 
+			usb2: gadget at f803c000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "atmel,at91sam9rl-udc";
+				reg = <0x00500000 0x80000
+				       0xf803c000 0x400>;
+				interrupts = <23 IRQ_TYPE_LEVEL_HIGH 0>;
+				status = "disabled";
+
+				ep0 {
+					reg = <0>;
+					atmel,fifo-size = <64>;
+					atmel,nb-banks = <1>;
+				};
+
+				ep1 {
+					reg = <1>;
+					atmel,fifo-size = <1024>;
+					atmel,nb-banks = <2>;
+					atmel,can-dma;
+					atmel,can-isoc;
+				};
+
+				ep2 {
+					reg = <2>;
+					atmel,fifo-size = <1024>;
+					atmel,nb-banks = <2>;
+					atmel,can-dma;
+					atmel,can-isoc;
+				};
+
+				ep3 {
+					reg = <3>;
+					atmel,fifo-size = <1024>;
+					atmel,nb-banks = <3>;
+					atmel,can-dma;
+				};
+
+				ep4 {
+					reg = <4>;
+					atmel,fifo-size = <1024>;
+					atmel,nb-banks = <3>;
+					atmel,can-dma;
+				};
+
+				ep5 {
+					reg = <5>;
+					atmel,fifo-size = <1024>;
+					atmel,nb-banks = <3>;
+					atmel,can-dma;
+					atmel,can-isoc;
+				};
+
+				ep6 {
+					reg = <6>;
+					atmel,fifo-size = <1024>;
+					atmel,nb-banks = <3>;
+					atmel,can-dma;
+					atmel,can-isoc;
+				};
+			};
+
 			rtc at fffffeb0 {
 				compatible = "atmel,at91rm9200-rtc";
 				reg = <0xfffffeb0 0x40>;
arch/arm/mach-at91/at91sam9x5.c +2 -0
index e631fec..2abee66 100644
@@ -249,6 +249,8 @@ static struct clk_lookup periph_clocks_lookups[] = {
 	CLKDEV_CON_DEV_ID("hclk", "600000.ohci", &uhphs_clk),
 	CLKDEV_CON_DEV_ID("ohci_clk", "600000.ohci", &uhphs_clk),
 	CLKDEV_CON_DEV_ID("ehci_clk", "700000.ehci", &uhphs_clk),
+	CLKDEV_CON_DEV_ID("hclk", "500000.gadget", &utmi_clk),
+	CLKDEV_CON_DEV_ID("pclk", "500000.gadget", &udphs_clk),
 };
 
 /*
Signature · 1 line
1.7.10.4
#3 lore raw

PATCH v3 3/5 ARM: at91: sam9x5ek add udc DT support

In reply to Jean-Christophe PLAGNIOL-VILLARD
---
 arch/arm/boot/dts/at91sam9x5ek.dtsi |    5 +++++
 1 file changed, 5 insertions(+)
arch/arm/boot/dts/at91sam9x5ek.dtsi +5 -0
index 19c8ebb..5e10027 100644
@@ -52,6 +52,11 @@
 				status = "okay";
 			};
 
+			usb2: gadget at f803c000 {
+				atmel,vbus-gpio = <&pioB 16 GPIO_ACTIVE_HIGH>;
+				status = "okay";
+			};
+
 			i2c0: i2c at f8010000 {
 				status = "okay";
 			};
Signature · 1 line
1.7.10.4
#4 lore raw

PATCH v3 4/5 ARM: at91: sam9g45 add udc DT support

In reply to Jean-Christophe PLAGNIOL-VILLARD
---
 arch/arm/boot/dts/at91sam9g45.dtsi |   62 ++++++++++++++++++++++++++++++++++++
 arch/arm/mach-at91/at91sam9g45.c   |    2 ++
 2 files changed, 64 insertions(+)
arch/arm/boot/dts/at91sam9g45.dtsi +62 -0
index f0091af..fccc488 100644
@@ -582,6 +582,68 @@
 				pinctrl-0 = <&pinctrl_spi1>;
 				status = "disabled";
 			};
+
+			usb2: gadget at fff78000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "atmel,at91sam9rl-udc";
+				reg = <0x00600000 0x80000
+				       0xfff78000 0x400>;
+				interrupts = <27 IRQ_TYPE_LEVEL_HIGH 0>;
+				status = "disabled";
+
+				ep0 {
+					reg = <0>;
+					atmel,fifo-size = <64>;
+					atmel,nb-banks = <1>;
+				};
+
+				ep1 {
+					reg = <1>;
+					atmel,fifo-size = <1024>;
+					atmel,nb-banks = <2>;
+					atmel,can-dma;
+					atmel,can-isoc;
+				};
+
+				ep2 {
+					reg = <2>;
+					atmel,fifo-size = <1024>;
+					atmel,nb-banks = <2>;
+					atmel,can-dma;
+					atmel,can-isoc;
+				};
+
+				ep3 {
+					reg = <3>;
+					atmel,fifo-size = <1024>;
+					atmel,nb-banks = <3>;
+					atmel,can-dma;
+				};
+
+				ep4 {
+					reg = <4>;
+					atmel,fifo-size = <1024>;
+					atmel,nb-banks = <3>;
+					atmel,can-dma;
+				};
+
+				ep5 {
+					reg = <5>;
+					atmel,fifo-size = <1024>;
+					atmel,nb-banks = <3>;
+					atmel,can-dma;
+					atmel,can-isoc;
+				};
+
+				ep6 {
+					reg = <6>;
+					atmel,fifo-size = <1024>;
+					atmel,nb-banks = <3>;
+					atmel,can-dma;
+					atmel,can-isoc;
+				};
+			};
 		};
 
 		nand0: nand at 40000000 {
arch/arm/mach-at91/at91sam9g45.c +2 -0
index 8b7fce0..95a418a 100644
@@ -266,6 +266,8 @@ static struct clk_lookup periph_clocks_lookups[] = {
 	CLKDEV_CON_DEV_ID(NULL, "fff88000.i2c", &twi1_clk),
 	CLKDEV_CON_DEV_ID("spi_clk", "fffa4000.spi", &spi0_clk),
 	CLKDEV_CON_DEV_ID("spi_clk", "fffa8000.spi", &spi1_clk),
+	CLKDEV_CON_DEV_ID("hclk", "600000.gadget", &utmi_clk),
+	CLKDEV_CON_DEV_ID("pclk", "600000.gadget", &udphs_clk),
 	/* fake hclk clock */
 	CLKDEV_CON_DEV_ID("hclk", "at91_ohci", &uhphs_clk),
 	CLKDEV_CON_DEV_ID(NULL, "fffff200.gpio", &pioA_clk),
Signature · 1 line
1.7.10.4
#5 lore raw

PATCH v3 5/5 ARM: at91: sam9m10g45ek add udc DT support

In reply to Jean-Christophe PLAGNIOL-VILLARD
---
 arch/arm/boot/dts/at91sam9m10g45ek.dts |    5 +++++
 1 file changed, 5 insertions(+)
arch/arm/boot/dts/at91sam9m10g45ek.dts +5 -0
index 89c50d1..17665ef 100644
@@ -112,6 +112,11 @@
 					reg = <0>;
 				};
 			};
+
+			usb2: gadget at fff78000 {
+				atmel,vbus-gpio = <&pioB 19 GPIO_ACTIVE_HIGH>;
+				status = "okay";
+			};
 		};
 
 		nand0: nand at 40000000 {
Signature · 1 line
1.7.10.4
#6 lore raw

PATCH 1/5 usb: add Atmel USBA UDC DT support

In reply to Jean-Christophe PLAGNIOL-VILLARD

Hi Jean-Christophe,

Quoted 17 lines · Jean-Christophe PLAGNIOL-VILLARD

Allow to compile the driver all the time if AT91 enabled.

Cc Nicolas Ferre <[email protected]>
Cc linux-usb at vger.kernel.org
---
  .../devicetree/bindings/usb/atmel-usb.txt          |   82 ++++++++
  drivers/usb/gadget/Kconfig                         |    2 +-
  drivers/usb/gadget/atmel_usba_udc.c                |  214 +++++++++++++++-----
  drivers/usb/gadget/atmel_usba_udc.h                |    1 +
  4 files changed, 244 insertions(+), 55 deletions(-)
Documentation/devicetree/bindings/usb/atmel-usb.txt +0 -0
index 60bd215..878556b2 100644

Documentation/devicetree/bindings/usb/atmel-usb.txt usb1: gadget at fffa4000 { · line 56

Quoted 10 lines
Documentation/devicetree/bindings/usb/atmel-usb.txt +7 -0
@@ -47,3 +47,85 @@ usb1: gadget at fffa4000 {
  	interrupts = <10 4>;
  	atmel,vbus-gpio = <&pioC 5 0>;
  };
+
+Atmel High-Speed USB device controller
+
+Required properties:
+ - compatible: Should be "atmel,at91sam9rl-udc"
+ - reg: Address and length of the register set for the device
+ - interrupts: Should contain macb interrupt

s/macb/udphs

Documentation/devicetree/bindings/usb/atmel-usb.txt usb1: gadget at fffa4000 { · line 57

Quoted 1 line
Documentation/devicetree/bindings/usb/atmel-usb.txt +1 -0
+ - ep childnode: To specifiy the number of endpoints and their properties.

s/specifiy/specify

Quoted 10 lines
Documentation/devicetree/bindings/usb/atmel-usb.txt +10 -0
+
+Optional properties:
+ - atmel,vbus-gpio: If present, specifies a gpio that needs to be
+   activated for the bus to be powered.
+
+Required child node properties:
+ - name: Name of the endpoint.
+ - reg: Num of the endpoint.
+ - atmel,fifo-size: Size of the fifo.
+ - atmel,nb-banks: Number of banks.

Documentation/devicetree/bindings/usb/atmel-usb.txt usb1: gadget at fffa4000 { · line 77

Quoted 10 lines
Documentation/devicetree/bindings/usb/atmel-usb.txt +10 -0
+ - atmel,can-dma: Boolean to specify if the endpoint support DMA.
+ - atmel,can-isoc: Boolean to specify if the endpoint support ISOC.
+
+usb2: gadget at fff78000 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	compatible = "atmel,at91sam9rl-udc";
+	reg = <0x00600000 0x80000
+	       0xfff78000 0x400>;
+	interrupts = <27 4>;

s/interrupts = <27 4>/interrupts = <27 IRQ_TYPE_LEVEL_HIGH 0>;

Quoted 99 lines
Documentation/devicetree/bindings/usb/atmel-usb.txt +54 -0
+	atmel,vbus-gpio = <&pioB 19 0>;
+
+	ep0 {
+		reg = <0>;
+		atmel,fifo-size = <64>;
+		atmel,nb-banks = <1>;
+	};
+
+	ep1 {
+		reg = <1>;
+		atmel,fifo-size = <1024>;
+		atmel,nb-banks = <2>;
+		atmel,can-dma;
+		atmel,can-isoc;
+	};
+
+	ep2 {
+		reg = <2>;
+		atmel,fifo-size = <1024>;
+		atmel,nb-banks = <2>;
+		atmel,can-dma;
+		atmel,can-isoc;
+	};
+
+	ep3 {
+		reg = <3>;
+		atmel,fifo-size = <1024>;
+		atmel,nb-banks = <3>;
+		atmel,can-dma;
+	};
+
+	ep4 {
+		reg = <4>;
+		atmel,fifo-size = <1024>;
+		atmel,nb-banks = <3>;
+		atmel,can-dma;
+	};
+
+	ep5 {
+		reg = <5>;
+		atmel,fifo-size = <1024>;
+		atmel,nb-banks = <3>;
+		atmel,can-dma;
+		atmel,can-isoc;
+	};
+
+	ep6 {
+		reg = <6>;
+		atmel,fifo-size = <1024>;
+		atmel,nb-banks = <3>;
+		atmel,can-dma;
+		atmel,can-isoc;
+	};
+};
drivers/usb/gadget/Kconfig +1 -1
index 83300d9..5e47d50 100644
@@ -156,7 +156,7 @@ config USB_LPC32XX
 
  config USB_ATMEL_USBA
  	tristate "Atmel USBA"
-	depends on AVR32 || ARCH_AT91SAM9RL || ARCH_AT91SAM9G45
+	depends on AVR32 || ARCH_AT91
  	help
  	  USBA is the integrated high-speed USB Device controller on
  	  the AT32AP700x, some AT91SAM9 and AT91CAP9 processors from Atmel.
drivers/usb/gadget/atmel_usba_udc.c +16 -1
index f2a970f..b3084b9 100644
@@ -22,6 +22,8 @@
  #include <linux/usb/atmel_usba_udc.h>
  #include <linux/delay.h>
  #include <linux/platform_data/atmel.h>
+#include <linux/of.h>
+#include <linux/of_gpio.h>
 
  #include <asm/gpio.h>
 
@@ -1835,9 +1837,143 @@ static int atmel_usba_stop(struct usb_gadget *gadget,
  	return 0;
  }
 
-static int __init usba_udc_probe(struct platform_device *pdev)
+#ifdef CONFIG_OF
+static struct usba_ep * atmel_udc_of_init(struct platform_device *pdev,
+						    struct usba_udc *udc)
+{
+	u32 val;
+	const char *name;
+	enum of_gpio_flags flags;
+	struct device_node *np = pdev->dev.of_node;
+	struct device_node *pp;
+	int i, ret;
+	struct usba_ep *eps, *ep;
+
+	udc->num_ep = 0;
+

drivers/usb/gadget/atmel_usba_udc.c static int atmel_usba_stop(struct usb_gadget *gadget, · line 1863

Quoted 10 lines
drivers/usb/gadget/atmel_usba_udc.c +10 -0
+	udc->vbus_pin = of_get_named_gpio_flags(np, "atmel,vbus-gpio", 0,
+						&flags);
+	udc->vbus_pin_inverted = (flags & OF_GPIO_ACTIVE_LOW) ? 1 : 0;
+
+	pp = NULL;
+	while ((pp = of_get_next_child(np, pp)))
+		udc->num_ep++;
+
+	eps = devm_kzalloc(&pdev->dev, sizeof(struct usba_ep) * udc->num_ep,
+			   GFP_KERNEL);

Using devm_kzalloc will cause issue when build as modules, and load and unload this driver, the second time unload, it will come out following segment fault, log as following. Using kzalloc will fix it.

---8>---

Unable to handle kernel NULL pointer dereference at virtual address 00000054
pgd = c7bac000
[00000054] *pgd=27b6f831, *pte=00000000, *ppte=00000000
Internal error: Oops: 17 [#1] ARM
Modules linked in: atmel_usba_udc(-) [last unloaded: atmel_usba_udc]
CPU: 0 PID: 519 Comm: rmmod Not tainted 3.10.0-rc1+ #13
task: c796d580 ti: c7b68000 task.ti: c7b68000
PC is at kfree+0x4c/0xb4
LR is at free_module+0xe4/0x168
pc : [<c007470c>]    lr : [<c0045884>]    psr: 40000093

sp : c7b69f10 ip : 00000010 fp : 00000000
r10: 00000000 r9 : c7b68000 r8 : c0009484
r7 : 00000000 r6 : c7ba0c00 r5 : a0000013 r4 : bf009240 r3 : c061d400 r2 : 00000000 r1 : 00007ba0 r0 : c7ba0c00
Flags: nZcv IRQs off FIQs on Mode SVC_32 ISA ARM Segment user
Control: 0005317f Table: 27bac000 DAC: 00000015 Process rmmod (pid: 519, stack limit = 0xc7b681b8)

Stack: (0xc7b69f10 to 0xc7b6a000)

9f00: 0000000f bf009240 000000a8
bf009288
9f20: c7afe6a8 c0045884 bf009240 00000000 00000013 becbfbd0 c0009484 c0045c10
9f40: 00000000 656d7461 73755f6c 755f6162 b6006364 b6f1c000 c796d580 b6f1c000
9f60: b6f1c000 c7afb140 00000000 becbf984 00005401 00000001 c7b68000 00000000
9f80: bf009240 00000880 c7b69f8c 00000000 becbf9bc b6f0a380 00000880 becbfbd0
9fa0: 00000081 c0009320 b6f0a380 00000880 becbfbd0 00000880 0000000e 00000000
9fc0: b6f0a380 00000880 becbfbd0 00000081 0000009c 0000ce8c 0000b7f0 00000000
9fe0: b6ebda20 becbfbc0 00019750 b6ebda2c a0000010 becbfbd0 00000000 00000000
[<c007470c>] (kfree+0x4c/0xb4) from [<c0045884>] (free_module+0xe4/0x168) [<c0045884>] (free_module+0xe4/0x168) from [<c0045c10>] (SyS_delete_module+0x1d8/0x210)
[<c0045c10>] (SyS_delete_module+0x1d8/0x210) from [<c0009320>] (ret_fast_syscall+0x0/0x2c)

Code: e7922281 e3120902 1593301c e593701c (e5974054)
---[ end trace cb98ff9cd16ea901 ]---

Segmentation fault
---<8---

Quoted 266 lines
drivers/usb/gadget/atmel_usba_udc.c +134 -53
+	if (!eps)
+		return ERR_PTR(-ENOMEM);
+
+	udc->gadget.ep0 = &eps[0].ep;
+
+	INIT_LIST_HEAD(&eps[0].ep.ep_list);
+
+	pp = NULL;
+	i = 0;
+	while ((pp = of_get_next_child(np, pp))) {
+		ep = &eps[i];
+
+		ret = of_property_read_u32(pp, "reg", &val);
+		if (ret) {
+			dev_err(&pdev->dev, "of_probe: reg error(%d)\n", ret);
+			goto err;
+		}
+		ep->index = val;
+
+		ret = of_property_read_u32(pp, "atmel,fifo-size", &val);
+		if (ret) {
+			dev_err(&pdev->dev, "of_probe: fifo-size error(%d)\n", ret);
+			goto err;
+		}
+		ep->fifo_size = val;
+
+		ret = of_property_read_u32(pp, "atmel,nb-banks", &val);
+		if (ret) {
+			dev_err(&pdev->dev, "of_probe: nb-banks error(%d)\n", ret);
+			goto err;
+		}
+		ep->nr_banks = val;
+
+		ep->can_dma = of_property_read_bool(pp, "atmel,can-dma");
+		ep->can_isoc = of_property_read_bool(pp, "atmel,can-isoc");
+
+		ret = of_property_read_string(pp, "name", &name);
+		ep->ep.name = name;
+
+		ep->ep_regs = udc->regs + USBA_EPT_BASE(i);
+		ep->dma_regs = udc->regs + USBA_DMA_BASE(i);
+		ep->fifo = udc->fifo + USBA_FIFO_BASE(i);
+		ep->ep.ops = &usba_ep_ops;
+		ep->ep.maxpacket = ep->fifo_size;
+		ep->udc = udc;
+		INIT_LIST_HEAD(&ep->queue);
+
+		if (i)
+			list_add_tail(&ep->ep.ep_list, &udc->gadget.ep_list);
+
+		i++;
+	}
+
+	return eps;
+err:
+	return ERR_PTR(ret);
+}
+#else
+static struct usba_ep * atmel_udc_of_init(struct platform_device *pdev,
+						    struct usba_udc *udc)
+{
+	return ERR_PTR(-ENOSYS);
+}
+#endif
+
+static struct usba_ep * usba_udc_pdata(struct platform_device *pdev,
+						 struct usba_udc *udc)
  {
  	struct usba_platform_data *pdata = pdev->dev.platform_data;
+	struct usba_ep *eps;
+	int i;
+
+	if (!pdata)
+		return ERR_PTR(-ENXIO);
+
+	eps = devm_kzalloc(&pdev->dev, sizeof(struct usba_ep) * pdata->num_ep,
+			   GFP_KERNEL);
+	if (!eps)
+		return ERR_PTR(-ENOMEM);
+
+	udc->gadget.ep0 = &eps[0].ep;
+
+	udc->vbus_pin = pdata->vbus_pin;
+	udc->vbus_pin_inverted = pdata->vbus_pin_inverted;
+	udc->num_ep = pdata->num_ep;
+
+	INIT_LIST_HEAD(&eps[0].ep.ep_list);
+
+	for (i = 0; i < pdata->num_ep; i++) {
+		struct usba_ep *ep = &eps[i];
+
+		ep->ep_regs = udc->regs + USBA_EPT_BASE(i);
+		ep->dma_regs = udc->regs + USBA_DMA_BASE(i);
+		ep->fifo = udc->fifo + USBA_FIFO_BASE(i);
+		ep->ep.ops = &usba_ep_ops;
+		ep->ep.name = pdata->ep[i].name;
+		ep->fifo_size = ep->ep.maxpacket = pdata->ep[i].fifo_size;
+		ep->udc = udc;
+		INIT_LIST_HEAD(&ep->queue);
+		ep->nr_banks = pdata->ep[i].nr_banks;
+		ep->index = pdata->ep[i].index;
+		ep->can_dma = pdata->ep[i].can_dma;
+		ep->can_isoc = pdata->ep[i].can_isoc;
+
+		if (i)
+			list_add_tail(&ep->ep.ep_list, &udc->gadget.ep_list);
+	}
+
+	return eps;
+}
+
+static int __init usba_udc_probe(struct platform_device *pdev)
+{
  	struct resource *regs, *fifo;
  	struct clk *pclk, *hclk;
  	struct usba_udc *udc = &the_udc;
@@ -1845,7 +1981,7 @@ static int __init usba_udc_probe(struct platform_device *pdev)
 
  	regs = platform_get_resource(pdev, IORESOURCE_MEM, CTRL_IOMEM_ID);
  	fifo = platform_get_resource(pdev, IORESOURCE_MEM, FIFO_IOMEM_ID);
-	if (!regs || !fifo || !pdata)
+	if (!regs || !fifo)
  		return -ENXIO;
 
  	irq = platform_get_irq(pdev, 0);
@@ -1891,46 +2027,14 @@ static int __init usba_udc_probe(struct platform_device *pdev)
  	usba_writel(udc, CTRL, USBA_DISABLE_MASK);
  	clk_disable(pclk);
 
-	usba_ep = kzalloc(sizeof(struct usba_ep) * pdata->num_ep,
-			  GFP_KERNEL);
-	if (!usba_ep)
-		goto err_alloc_ep;
-
-	the_udc.gadget.ep0 = &usba_ep[0].ep;
-
-	INIT_LIST_HEAD(&usba_ep[0].ep.ep_list);
-	usba_ep[0].ep_regs = udc->regs + USBA_EPT_BASE(0);
-	usba_ep[0].dma_regs = udc->regs + USBA_DMA_BASE(0);
-	usba_ep[0].fifo = udc->fifo + USBA_FIFO_BASE(0);
-	usba_ep[0].ep.ops = &usba_ep_ops;
-	usba_ep[0].ep.name = pdata->ep[0].name;
-	usba_ep[0].ep.maxpacket = pdata->ep[0].fifo_size;
-	usba_ep[0].udc = &the_udc;
-	INIT_LIST_HEAD(&usba_ep[0].queue);
-	usba_ep[0].fifo_size = pdata->ep[0].fifo_size;
-	usba_ep[0].nr_banks = pdata->ep[0].nr_banks;
-	usba_ep[0].index = pdata->ep[0].index;
-	usba_ep[0].can_dma = pdata->ep[0].can_dma;
-	usba_ep[0].can_isoc = pdata->ep[0].can_isoc;
-
-	for (i = 1; i < pdata->num_ep; i++) {
-		struct usba_ep *ep = &usba_ep[i];
-
-		ep->ep_regs = udc->regs + USBA_EPT_BASE(i);
-		ep->dma_regs = udc->regs + USBA_DMA_BASE(i);
-		ep->fifo = udc->fifo + USBA_FIFO_BASE(i);
-		ep->ep.ops = &usba_ep_ops;
-		ep->ep.name = pdata->ep[i].name;
-		ep->ep.maxpacket = pdata->ep[i].fifo_size;
-		ep->udc = &the_udc;
-		INIT_LIST_HEAD(&ep->queue);
-		ep->fifo_size = pdata->ep[i].fifo_size;
-		ep->nr_banks = pdata->ep[i].nr_banks;
-		ep->index = pdata->ep[i].index;
-		ep->can_dma = pdata->ep[i].can_dma;
-		ep->can_isoc = pdata->ep[i].can_isoc;
+	if (pdev->dev.of_node)
+		usba_ep = atmel_udc_of_init(pdev, udc);
+	else
+		usba_ep = usba_udc_pdata(pdev, udc);
 
-		list_add_tail(&ep->ep.ep_list, &udc->gadget.ep_list);
+	if (IS_ERR(usba_ep)) {
+		ret = PTR_ERR(usba_ep);
+		goto err_alloc_ep;
  	}
 
  	ret = request_irq(irq, usba_udc_irq, 0, "atmel_usba_udc", udc);
@@ -1941,16 +2045,12 @@ static int __init usba_udc_probe(struct platform_device *pdev)
  	}
  	udc->irq = irq;
 
-	if (gpio_is_valid(pdata->vbus_pin)) {
-		if (!gpio_request(pdata->vbus_pin, "atmel_usba_udc")) {
-			udc->vbus_pin = pdata->vbus_pin;
-			udc->vbus_pin_inverted = pdata->vbus_pin_inverted;
-
+	if (gpio_is_valid(udc->vbus_pin)) {
+		if (!devm_gpio_request(&pdev->dev, udc->vbus_pin, "atmel_usba_udc")) {
  			ret = request_irq(gpio_to_irq(udc->vbus_pin),
  					usba_vbus_irq, 0,
  					"atmel_usba_udc", udc);
  			if (ret) {
-				gpio_free(udc->vbus_pin);
  				udc->vbus_pin = -ENODEV;
  				dev_warn(&udc->pdev->dev,
  					 "failed to request vbus irq; "
@@ -1969,16 +2069,14 @@ static int __init usba_udc_probe(struct platform_device *pdev)
  		goto err_add_udc;
 
  	usba_init_debugfs(udc);
-	for (i = 1; i < pdata->num_ep; i++)
+	for (i = 1; i < udc->num_ep; i++)
  		usba_ep_init_debugfs(udc, &usba_ep[i]);
 
  	return 0;
 
  err_add_udc:
-	if (gpio_is_valid(pdata->vbus_pin)) {
+	if (gpio_is_valid(udc->vbus_pin))
  		free_irq(gpio_to_irq(udc->vbus_pin), udc);
-		gpio_free(udc->vbus_pin);
-	}
 
  	free_irq(irq, udc);
  err_request_irq:
@@ -2001,19 +2099,17 @@ static int __exit usba_udc_remove(struct platform_device *pdev)
  {
  	struct usba_udc *udc;
  	int i;
-	struct usba_platform_data *pdata = pdev->dev.platform_data;
 
  	udc = platform_get_drvdata(pdev);
 
  	usb_del_gadget_udc(&udc->gadget);
 
-	for (i = 1; i < pdata->num_ep; i++)
+	for (i = 1; i < udc->num_ep; i++)
  		usba_ep_cleanup_debugfs(&usba_ep[i]);
  	usba_cleanup_debugfs(udc);
 
  	if (gpio_is_valid(udc->vbus_pin)) {
  		free_irq(gpio_to_irq(udc->vbus_pin), udc);
-		gpio_free(udc->vbus_pin);
  	}
 
  	free_irq(udc->irq, udc);
@@ -2026,11 +2122,21 @@ static int __exit usba_udc_remove(struct platform_device *pdev)
  	return 0;
  }
 
+#if defined(CONFIG_OF)
+static const struct of_device_id atmel_udc_dt_ids[] = {
+	{ .compatible = "atmel,at91sam9rl-udc" },
+	{ /* sentinel */ }
+};
+
+MODULE_DEVICE_TABLE(of, atmel_udc_dt_ids);
+#endif
+
  static struct platform_driver udc_driver = {
  	.remove		= __exit_p(usba_udc_remove),
  	.driver		= {
  		.name		= "atmel_usba_udc",
  		.owner		= THIS_MODULE,
+		.of_match_table	= of_match_ptr(atmel_udc_dt_ids),
  	},
  };
 
drivers/usb/gadget/atmel_usba_udc.h +0 -0
index d65a618..6999a26 100644

drivers/usb/gadget/atmel_usba_udc.h struct usba_udc { · line 323

Quoted 7 lines
drivers/usb/gadget/atmel_usba_udc.h +1 -0
@@ -317,6 +317,7 @@ struct usba_udc {
  	int irq;
  	int vbus_pin;
  	int vbus_pin_inverted;
+	int num_ep;
  	struct clk *pclk;
  	struct clk *hclk;
 

Best Regards,
Bo Shen

#7 lore raw

PATCH v3 1/5 usb: add Atmel USBA UDC DT support

Quoted 23 lines
Quoted 23 lines
drivers/usb/gadget/atmel_usba_udc.c +21 -1
-static int __init usba_udc_probe(struct platform_device *pdev)
+#ifdef CONFIG_OF
+static struct usba_ep * atmel_udc_of_init(struct platform_device *pdev,
+						    struct usba_udc *udc)
+{
+	u32 val;
+	const char *name;
+	enum of_gpio_flags flags;
+	struct device_node *np = pdev->dev.of_node;
+	struct device_node *pp;
+	int i, ret;
+	struct usba_ep *eps, *ep;
+
+	udc->num_ep = 0;
+
+	udc->vbus_pin = of_get_named_gpio_flags(np, "atmel,vbus-gpio", 0,
+						&flags);
+	udc->vbus_pin_inverted = (flags & OF_GPIO_ACTIVE_LOW) ? 1 : 0;
+
+	pp = NULL;
+	while ((pp = of_get_next_child(np, pp)))
+		udc->num_ep++;
Quoted 8 lines

drivers/usb/gadget/atmel_usba_udc.c static int atmel_usba_stop(struct usb_gadget *gadget, · line 1863

Quoted 3 lines
drivers/usb/gadget/atmel_usba_udc.c +3 -0
+
+	eps = devm_kzalloc(&pdev->dev, sizeof(struct usba_ep) * udc->num_ep,
+			   GFP_KERNEL);

Using devm_kzalloc will cause issue when build as modules, and load and unload this driver, the second time unload, it will come out following segment fault, log as following. Using kzalloc will fix it.

no devm_kzalloc is the right one to use

if there is a this not in the drivers and kzalloc is not the solution we need to find the real reason as devm_xxx are used everywhere by now

Best Regards,
J.

#8 lore raw

PATCH v3 1/5 usb: add Atmel USBA UDC DT support

Quoted 32 lines · Jean-Christophe PLAGNIOL-VILLARD
Quoted 23 lines
Quoted 23 lines
drivers/usb/gadget/atmel_usba_udc.c +21 -1
-static int __init usba_udc_probe(struct platform_device *pdev)
+#ifdef CONFIG_OF
+static struct usba_ep * atmel_udc_of_init(struct platform_device *pdev,
+						    struct usba_udc *udc)
+{
+	u32 val;
+	const char *name;
+	enum of_gpio_flags flags;
+	struct device_node *np = pdev->dev.of_node;
+	struct device_node *pp;
+	int i, ret;
+	struct usba_ep *eps, *ep;
+
+	udc->num_ep = 0;
+
+	udc->vbus_pin = of_get_named_gpio_flags(np, "atmel,vbus-gpio", 0,
+						&flags);
+	udc->vbus_pin_inverted = (flags & OF_GPIO_ACTIVE_LOW) ? 1 : 0;
+
+	pp = NULL;
+	while ((pp = of_get_next_child(np, pp)))
+		udc->num_ep++;
Quoted 8 lines

drivers/usb/gadget/atmel_usba_udc.c static int atmel_usba_stop(struct usb_gadget *gadget, · line 1863

Quoted 3 lines
drivers/usb/gadget/atmel_usba_udc.c +3 -0
+
+	eps = devm_kzalloc(&pdev->dev, sizeof(struct usba_ep) * udc->num_ep,
+			   GFP_KERNEL);

Using devm_kzalloc will cause issue when build as modules, and load and unload this driver, the second time unload, it will come out following segment fault, log as following. Using kzalloc will fix it.

Quoted 4 lines

no devm_kzalloc is the right one to use

if there is a this not in the drivers and kzalloc is not the solution we need to find the real reason as devm_xxx are used everywhere by now

The issue come from that the current driver have some hack that forbiden multi-instance

I'll drop that

so yes devm_kzalloc is the right alloc to use