USB: OMAP1: Tahvo USB support for 770

Move omap_usb_config to platform data, so that OTG driver can include it.

Signed-off-by Aaro Koskinen <[email protected]>

---
 arch/arm/mach-omap1/include/mach/usb.h  | 38 +-----------------------
 include/linux/platform_data/usb-omap1.h | 51 +++++++++++++++++++++++++++++++++
 2 files changed, 52 insertions(+), 37 deletions(-)
 create mode 100644 include/linux/platform_data/usb-omap1.h

arch/arm/mach-omap1/include/mach/usb.h +1 -37

index 45e5ac7..2c26305 100644
@@ -8,43 +8,7 @@
 #define	is_usb0_device(config)	0
 #endif
 
-struct omap_usb_config {
-	/* Configure drivers according to the connectors on your board:
-	 *  - "A" connector (rectagular)
-	 *	... for host/OHCI use, set "register_host".
-	 *  - "B" connector (squarish) or "Mini-B"
-	 *	... for device/gadget use, set "register_dev".
-	 *  - "Mini-AB" connector (very similar to Mini-B)
-	 *	... for OTG use as device OR host, initialize "otg"
-	 */
-	unsigned	register_host:1;
-	unsigned	register_dev:1;
-	u8		otg;	/* port number, 1-based:  usb1 == 2 */
-
-	u8		hmc_mode;
-
-	/* implicitly true if otg:  host supports remote wakeup? */
-	u8		rwc;
-
-	/* signaling pins used to talk to transceiver on usbN:
-	 *  0 == usbN unused
-	 *  2 == usb0-only, using internal transceiver
-	 *  3 == 3 wire bidirectional
-	 *  4 == 4 wire bidirectional
-	 *  6 == 6 wire unidirectional (or TLL)
-	 */
-	u8		pins[3];
-
-	struct platform_device *udc_device;
-	struct platform_device *ohci_device;
-	struct platform_device *otg_device;
-
-	u32 (*usb0_init)(unsigned nwires, unsigned is_device);
-	u32 (*usb1_init)(unsigned nwires);
-	u32 (*usb2_init)(unsigned nwires, unsigned alt_pingroup);
-
-	int (*ocpi_enable)(void);
-};
+#include <linux/platform_data/usb-omap1.h>
 
 void omap_otg_init(struct omap_usb_config *config);
 

include/linux/platform_data/usb-omap1.h new file +51 -0

new file mode 100644
index 0000000..8c7764d
@@ -0,0 +1,51 @@
+/*
+ * Platform data for OMAP1 USB
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License. See the file "COPYING" in the main directory of this archive for
+ * more details.
+ */
+#ifndef __LINUX_USB_OMAP1_H
+#define __LINUX_USB_OMAP1_H
+
+#include <linux/platform_device.h>
+
+struct omap_usb_config {
+	/* Configure drivers according to the connectors on your board:
+	 *  - "A" connector (rectagular)
+	 *	... for host/OHCI use, set "register_host".
+	 *  - "B" connector (squarish) or "Mini-B"
+	 *	... for device/gadget use, set "register_dev".
+	 *  - "Mini-AB" connector (very similar to Mini-B)
+	 *	... for OTG use as device OR host, initialize "otg"
+	 */
+	unsigned	register_host:1;
+	unsigned	register_dev:1;
+	u8		otg;	/* port number, 1-based:  usb1 == 2 */
+
+	u8		hmc_mode;
+
+	/* implicitly true if otg:  host supports remote wakeup? */
+	u8		rwc;
+
+	/* signaling pins used to talk to transceiver on usbN:
+	 *  0 == usbN unused
+	 *  2 == usb0-only, using internal transceiver
+	 *  3 == 3 wire bidirectional
+	 *  4 == 4 wire bidirectional
+	 *  6 == 6 wire unidirectional (or TLL)
+	 */
+	u8		pins[3];
+
+	struct platform_device *udc_device;
+	struct platform_device *ohci_device;
+	struct platform_device *otg_device;
+
+	u32 (*usb0_init)(unsigned nwires, unsigned is_device);
+	u32 (*usb1_init)(unsigned nwires);
+	u32 (*usb2_init)(unsigned nwires, unsigned alt_pingroup);
+
+	int (*ocpi_enable)(void);
+};
+
+#endif /* __LINUX_USB_OMAP1_H */

Signature · 1 line

1.8.3.1

Transceivers need to manage OTG controller state on OMAP1 to enable switching between peripheral and host modes. Provide a driver for that.

Signed-off-by Aaro Koskinen <[email protected]>

---
 drivers/usb/phy/Kconfig        |  10 +++
 drivers/usb/phy/Makefile       |   1 +
 drivers/usb/phy/phy-omap-otg.c | 171 +++++++++++++++++++++++++++++++++++++++++
 3 files changed, 182 insertions(+)
 create mode 100644 drivers/usb/phy/phy-omap-otg.c

drivers/usb/phy/Kconfig +10 -0

index 7ef3eb8..14a50bd 100644
@@ -135,6 +135,16 @@ config USB_GPIO_VBUS
 	  optionally control of a D+ pullup GPIO as well as a VBUS
 	  current limit regulator.
 
+config OMAP_OTG
+	tristate "OMAP USB OTG controller driver"
+	depends on ARCH_OMAP_OTG && EXTCON
+	help
+	  Enable this to support some transceivers on OMAP1 platforms. OTG
+	  controller is needed to switch between host and peripheral modes.
+
+	  This driver can also be built as a module. If so, the module
+	  will be called omap-otg.
+
 config USB_ISP1301
 	tristate "NXP ISP1301 USB transceiver support"
 	depends on USB || USB_GADGET

drivers/usb/phy/Makefile +1 -0

index a9169cb..c7f391b 100644
@@ -15,6 +15,7 @@ obj-$(CONFIG_ISP1301_OMAP)		+= phy-isp1301-omap.o
 obj-$(CONFIG_MV_U3D_PHY)		+= phy-mv-u3d-usb.o
 obj-$(CONFIG_NOP_USB_XCEIV)		+= phy-nop.o
 obj-$(CONFIG_OMAP_CONTROL_USB)		+= phy-omap-control.o
+obj-$(CONFIG_OMAP_OTG)			+= phy-omap-otg.o
 obj-$(CONFIG_OMAP_USB2)			+= phy-omap-usb2.o
 obj-$(CONFIG_OMAP_USB3)			+= phy-omap-usb3.o
 obj-$(CONFIG_SAMSUNG_USBPHY)		+= phy-samsung-usb.o

drivers/usb/phy/phy-omap-otg.c new file +19 -0

new file mode 100644
index 0000000..2a8c674
@@ -0,0 +1,171 @@
+/*
+ * OMAP OTG controller driver
+ *
+ * Based on code from tahvo-usb.c and isp1301_omap.c drivers.
+ *
+ * Copyright (C) 2005-2006 Nokia Corporation
+ * Copyright (C) 2004 Texas Instruments
+ * Copyright (C) 2004 David Brownell
+ *
+ * This file is subject to the terms and conditions of the GNU General
+ * Public License. See the file "COPYING" in the main directory of this
+ * archive for more details.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+

Quoted 1 line · Aaro Koskinen

+#include <mach/usb.h>

no mach/* includes under drivers/usb, sorry. It's a pain to fix those up later.

Add platform data for Tahvo.

Signed-off-by Aaro Koskinen <[email protected]>