Skip to contentSkip to conversation

spi: spi-ep93xx: always handle transfer specific settings

PATCH Applied H Hartley Sweeten 1 participant 1 message Jul 2, 2013 SPI

lore
Share & tools
lore

H Hartley Sweeten

author
#0 lore raw

PATCH v2 1/11 spi: spi-ep93xx: always handle transfer specific settings

__spi_async(), which starts every SPI message transfer, initializes the bits_per_word and max speed for every transfer in the message. Since the conditional test in ep93xx_spi_process_transfer() will always succeed just remove it and always call ep93xx_spi_chip_setup() to configure the hardware for each transfer in the message.

Remove the redundant ep93xx_spi_chp_setup() in ep93xx_spi_process_transfer() which just initializes the hardware to the "default" based on the SPI device.

Signed-off-by H Hartley Sweeten <[email protected]>
Cc Ryan Mallon <[email protected]>
Cc Mika Westerberg <[email protected]>
Cc Mark Brown <[email protected]>
Cc Grant Likely <[email protected]>
---
 drivers/spi/spi-ep93xx.c | 43 ++++++++++---------------------------------
 1 file changed, 10 insertions(+), 33 deletions(-)
drivers/spi/spi-ep93xx.c +10 -33
index cad30b8..11e2b99 100644
@@ -708,38 +708,20 @@ static void ep93xx_spi_process_transfer(struct ep93xx_spi *espi,
 					struct spi_transfer *t)
 {
 	struct ep93xx_spi_chip *chip = spi_get_ctldata(msg->spi);
+	int err;
 
 	msg->state = t;
 
-	/*
-	 * Handle any transfer specific settings if needed. We use
-	 * temporary chip settings here and restore original later when
-	 * the transfer is finished.
-	 */
-	if (t->speed_hz || t->bits_per_word) {
-		struct ep93xx_spi_chip tmp_chip = *chip;
-
-		if (t->speed_hz) {
-			int err;
-
-			err = ep93xx_spi_calc_divisors(espi, &tmp_chip,
-						       t->speed_hz);
-			if (err) {
-				dev_err(&espi->pdev->dev,
-					"failed to adjust speed\n");
-				msg->status = err;
-				return;
-			}
-		}
+	err = ep93xx_spi_calc_divisors(espi, chip, t->speed_hz);
+	if (err) {
+		dev_err(&espi->pdev->dev, "failed to adjust speed\n");
+		msg->status = err;
+		return;
+	}
 
-		if (t->bits_per_word)
-			tmp_chip.dss = bits_per_word_to_dss(t->bits_per_word);
+	chip->dss = bits_per_word_to_dss(t->bits_per_word);
 
-		/*
-		 * Set up temporary new hw settings for this transfer.
-		 */
-		ep93xx_spi_chip_setup(espi, &tmp_chip);
-	}
+	ep93xx_spi_chip_setup(espi, chip);
 
 	espi->rx = 0;
 	espi->tx = 0;

@@ -783,9 +765,6 @@ static void ep93xx_spi_process_transfer(struct ep93xx_spi *espi,
 			ep93xx_spi_cs_control(msg->spi, true);
 		}
 	}
-
-	if (t->speed_hz || t->bits_per_word)
-		ep93xx_spi_chip_setup(espi, chip);
 }
 
 /*

@@ -838,10 +817,8 @@ static void ep93xx_spi_process_message(struct ep93xx_spi *espi,
 	espi->fifo_level = 0;
 
 	/*
-	 * Update SPI controller registers according to spi device and assert
-	 * the chipselect.
+	 * Assert the chipselect.
 	 */
-	ep93xx_spi_chip_setup(espi, spi_get_ctldata(msg->spi));
 	ep93xx_spi_cs_control(msg->spi, true);
 
 	list_for_each_entry(t, &msg->transfers, transfer_list) {
Signature · 1 line
1.8.1.4