Skip to contentSkip to conversation

mfd:rtsx: MFD patches for Realtek cardreader

PATCH Superseded [email protected] 3 participants 8 messages Jul 17, 2013 – Aug 20, 2013 Multifunction devices (MFD)

v2 of 3 Superseded Latest is v3 →

lore
Share & tools
lore
#0 lore raw

v2 cover mfd:rtsx: MFD patches for Realtek cardreader

From: Wei WANG <[email protected]>

v2:
Use macro when initializing vendor settings

Wei WANG (5):
mfd:rtsx: Read vendor setting from config space mfd:rtsx: Add shutdown callback in rtsx_pci_driver mfd:rtsx: Move some actions from rtsx_pci_init_hw to individual
extra_init_hw
mfd:rtsx: Clear hardware PFM mode in rtl8411b mfd:rtsx: Configure to enter a deeper power-saving mode in S3

 drivers/mfd/rtl8411.c           |   90 +++++++++++++++++++++++++++---
 drivers/mfd/rts5209.c           |   61 +++++++++++++++------
 drivers/mfd/rts5227.c           |  115 +++++++++++++++++++++++++++++++--------
 drivers/mfd/rts5229.c           |   51 +++++++++++++++--
 drivers/mfd/rts5249.c           |  110 ++++++++++++++++++++++++++++++-------
 drivers/mfd/rtsx_pcr.c          |   76 +++++++++++++++++++-------
 drivers/mfd/rtsx_pcr.h          |   32 ++++++++++-
 include/linux/mfd/rtsx_common.h |    3 +-
 include/linux/mfd/rtsx_pci.h    |   35 ++++++++++--
 9 files changed, 470 insertions(+), 103 deletions(-)
Signature · 1 line
1.7.9.5
#1 lore raw

PATCH v2 1/5 mfd:rtsx: Read vendor setting from config space

From: Wei WANG <[email protected]>

Normally OEMs will set vendor setting to the config space of Realtek card reader in BIOS stage. This patch reads the setting at the first, and configure the internal registers according to it, to improve card reader's compatibility condition.

---
 drivers/mfd/rtl8411.c           |   81 ++++++++++++++++++++++++++++----
 drivers/mfd/rts5209.c           |   51 +++++++++++++-------
 drivers/mfd/rts5227.c           |   98 +++++++++++++++++++++++++++++----------
 drivers/mfd/rts5229.c           |   41 ++++++++++++++--
 drivers/mfd/rts5249.c           |   93 ++++++++++++++++++++++++++++---------
 drivers/mfd/rtsx_pcr.c          |   29 ++++++++++--
 drivers/mfd/rtsx_pcr.h          |   32 ++++++++++++-
 include/linux/mfd/rtsx_common.h |    3 +-
 include/linux/mfd/rtsx_pci.h    |   21 +++++++--
 9 files changed, 362 insertions(+), 87 deletions(-)
drivers/mfd/rtl8411.c +73 -8
index c436bf2..1fbb978 100644
@@ -1,6 +1,6 @@
 /* Driver for Realtek PCI-Express card reader
  *
- * Copyright(c) 2009 Realtek Semiconductor Corp. All rights reserved.
+ * Copyright(c) 2009-2013 Realtek Semiconductor Corp. All rights reserved.
  *
  * This program is free software; you can redistribute it and/or modify it
  * under the terms of the GNU General Public License as published by the
@@ -17,7 +17,7 @@
  *
  * Author:
  *   Wei WANG <[email protected]>
- *   No. 450, Shenhu Road, Suzhou Industry Park, Suzhou, China
+ *   Roger Tseng <[email protected]>
  */
 
 #include <linux/module.h>
@@ -47,19 +47,70 @@ static int rtl8411b_is_qfn48(struct rtsx_pcr *pcr)
 		return 0;
 }
 
+static void rtl8411_init_settings(struct rtsx_pcr *pcr)
+{
+	u32 reg1;
+	u8 reg3;
+
+	rtsx_pci_read_config_dword(pcr, PCR_SETTING_REG1, &reg1);
+	dev_dbg(&(pcr->pci->dev), "Cfg 0x%x: 0x%x\n", PCR_SETTING_REG1, reg1);
+
+	if (rtsx_vendor_setting_valid(reg1)) {
+		pcr->aspm_en = rtsx_reg_to_aspm(reg1);
+		pcr->sd30_drive_sel_1v8 =
+			map_sd_drive(rtsx_reg_to_sd30_drive_sel_1v8(reg1));
+		pcr->card_drive_sel &= 0x3F;
+		pcr->card_drive_sel |= rtsx_reg_to_card_drive_sel(reg1);
+
+		rtsx_pci_read_config_byte(pcr, PCR_SETTING_REG3, &reg3);
+		dev_dbg(&(pcr->pci->dev), "Cfg 0x%x: 0x%x\n",
+				PCR_SETTING_REG3, reg3);
+		pcr->sd30_drive_sel_3v3 =
+			rtl8411_reg_to_sd30_drive_sel_3v3(reg3);
+	}
+}
+
+static void rtl8411b_init_settings(struct rtsx_pcr *pcr)
+{
+	u32 reg;
+
+	rtsx_pci_read_config_dword(pcr, PCR_SETTING_REG1, &reg);
+	dev_dbg(&(pcr->pci->dev), "Cfg 0x%x: 0x%x\n", PCR_SETTING_REG1, reg);
+
+	if (rtsx_vendor_setting_valid(reg)) {
+		pcr->aspm_en = rtsx_reg_to_aspm(reg);
+		pcr->sd30_drive_sel_1v8 =
+			map_sd_drive(rtsx_reg_to_sd30_drive_sel_1v8(reg));
+		pcr->sd30_drive_sel_3v3 =
+			map_sd_drive(rtl8411b_reg_to_sd30_drive_sel_3v3(reg));
+	}
+}
+
 static int rtl8411_extra_init_hw(struct rtsx_pcr *pcr)
 {
-	return rtsx_pci_write_register(pcr, CD_PAD_CTL,
+	rtsx_pci_init_cmd(pcr);
+
+	rtsx_pci_add_cmd(pcr, WRITE_REG_CMD, SD30_DRIVE_SEL,
+			0xFF, pcr->sd30_drive_sel_3v3);
+	rtsx_pci_add_cmd(pcr, WRITE_REG_CMD, CD_PAD_CTL,
 			CD_DISABLE_MASK | CD_AUTO_DISABLE, CD_ENABLE);
+
+	return rtsx_pci_send_cmd(pcr, 100);
 }
 
 static int rtl8411b_extra_init_hw(struct rtsx_pcr *pcr)
 {
-	if (rtl8411b_is_qfn48(pcr))
-		rtsx_pci_write_register(pcr, CARD_PULL_CTL3, 0xFF, 0xF5);
+	rtsx_pci_init_cmd(pcr);
 
-	return rtsx_pci_write_register(pcr, CD_PAD_CTL,
+	if (rtl8411b_is_qfn48(pcr))
+		rtsx_pci_add_cmd(pcr, WRITE_REG_CMD,
+				CARD_PULL_CTL3, 0xFF, 0xF5);
+	rtsx_pci_add_cmd(pcr, WRITE_REG_CMD, SD30_DRIVE_SEL,
+			0xFF, pcr->sd30_drive_sel_3v3);
+	rtsx_pci_add_cmd(pcr, WRITE_REG_CMD, CD_PAD_CTL,
 			CD_DISABLE_MASK | CD_AUTO_DISABLE, CD_ENABLE);
+
+	return rtsx_pci_send_cmd(pcr, 100);
 }
 
 static int rtl8411_turn_on_led(struct rtsx_pcr *pcr)
@@ -141,13 +192,13 @@ static int rtl8411_switch_output_voltage(struct rtsx_pcr *pcr, u8 voltage)
 	mask = (BPP_REG_TUNED18 << BPP_TUNED18_SHIFT_8411) | BPP_PAD_MASK;
 	if (voltage == OUTPUT_3V3) {
 		err = rtsx_pci_write_register(pcr,
-				SD30_DRIVE_SEL, 0x07, DRIVER_TYPE_D);
+				SD30_DRIVE_SEL, 0x07, pcr->sd30_drive_sel_3v3);
 		if (err < 0)
 			return err;
 		val = (BPP_ASIC_3V3 << BPP_TUNED18_SHIFT_8411) | BPP_PAD_3V3;
 	} else if (voltage == OUTPUT_1V8) {
 		err = rtsx_pci_write_register(pcr,
-				SD30_DRIVE_SEL, 0x07, DRIVER_TYPE_B);
+				SD30_DRIVE_SEL, 0x07, pcr->sd30_drive_sel_1v8);
 		if (err < 0)
 			return err;
 		val = (BPP_ASIC_1V8 << BPP_TUNED18_SHIFT_8411) | BPP_PAD_1V8;
@@ -222,6 +273,7 @@ static int rtl8411_conv_clk_and_div_n(int input, int dir)
 }
 
 static const struct pcr_ops rtl8411_pcr_ops = {
+	.init_settings = rtl8411_init_settings,
 	.extra_init_hw = rtl8411_extra_init_hw,
 	.optimize_phy = NULL,
 	.turn_on_led = rtl8411_turn_on_led,
@@ -236,6 +288,7 @@ static const struct pcr_ops rtl8411_pcr_ops = {
 };
 
 static const struct pcr_ops rtl8411b_pcr_ops = {
+	.init_settings = rtl8411b_init_settings,
 	.extra_init_hw = rtl8411b_extra_init_hw,
 	.optimize_phy = NULL,
 	.turn_on_led = rtl8411_turn_on_led,
@@ -385,6 +438,12 @@ void rtl8411_init_params(struct rtsx_pcr *pcr)
 	pcr->num_slots = 2;
 	pcr->ops = &rtl8411_pcr_ops;
 
+	pcr->flags = 0;
+	pcr->card_drive_sel = 0x55;
+	pcr->sd30_drive_sel_1v8 = 0x03;
+	pcr->sd30_drive_sel_3v3 = 0x01;
+	pcr->aspm_en = 0x02;
+
 	pcr->ic_version = rtl8411_get_ic_version(pcr);
 	pcr->sd_pull_ctl_enable_tbl = rtl8411_sd_pull_ctl_enable_tbl;
 	pcr->sd_pull_ctl_disable_tbl = rtl8411_sd_pull_ctl_disable_tbl;
@@ -398,6 +457,12 @@ void rtl8411b_init_params(struct rtsx_pcr *pcr)
 	pcr->num_slots = 2;
 	pcr->ops = &rtl8411b_pcr_ops;
 
+	pcr->flags = 0;
+	pcr->card_drive_sel = 0x55;
+	pcr->sd30_drive_sel_1v8 = 0x03;
+	pcr->sd30_drive_sel_3v3 = 0x01;
+	pcr->aspm_en = 0x02;
+
 	pcr->ic_version = rtl8411_get_ic_version(pcr);
 
 	if (rtl8411b_is_qfn48(pcr)) {
drivers/mfd/rts5209.c +34 -17

119 lines not on this page · raw message

drivers/mfd/rts5227.c +74 -24

155 lines not on this page · raw message

drivers/mfd/rts5229.c +36 -5

94 lines not on this page · raw message

drivers/mfd/rts5249.c +72 -21

144 lines not on this page · raw message

drivers/mfd/rtsx_pcr.c +24 -5
index dd186c4..e81d6cf 100644
@@ -1,6 +1,6 @@
 /* Driver for Realtek PCI-Express card reader
  *
- * Copyright(c) 2009 Realtek Semiconductor Corp. All rights reserved.
+ * Copyright(c) 2009-2013 Realtek Semiconductor Corp. All rights reserved.
  *
  * This program is free software; you can redistribute it and/or modify it
  * under the terms of the GNU General Public License as published by the
@@ -17,7 +17,6 @@
  *
  * Author:
  *   Wei WANG <[email protected]>
- *   No. 450, Shenhu Road, Suzhou Industry Park, Suzhou, China
  */
 
 #include <linux/pci.h>
@@ -73,6 +72,9 @@ void rtsx_pci_start_run(struct rtsx_pcr *pcr)
 		pcr->state = PDEV_STAT_RUN;
 		if (pcr->ops->enable_auto_blink)
 			pcr->ops->enable_auto_blink(pcr);
+
+		if (pcr->aspm_en)
+			rtsx_pci_write_config_byte(pcr, LCTLR, 0);
 	}
 
 	mod_delayed_work(system_wq, &pcr->idle_work, msecs_to_jiffies(200));
@@ -717,7 +719,7 @@ int rtsx_pci_card_exclusive_check(struct rtsx_pcr *pcr, int card)
 		[RTSX_MS_CARD] = MS_EXIST
 	};
 
-	if (!pcr->ms_pmos) {
+	if (!(pcr->flags & PCR_MS_PMOS)) {
 		/* When using single PMOS, accessing card is not permitted
 		 * if the existing card is not the designated one.
 		 */
@@ -918,6 +920,9 @@ static void rtsx_pci_idle_work(struct work_struct *work)
 	if (pcr->ops->turn_off_led)
 		pcr->ops->turn_off_led(pcr);
 
+	if (pcr->aspm_en)
+		rtsx_pci_write_config_byte(pcr, LCTLR, pcr->aspm_en);
+
 	mutex_unlock(&pcr->pcr_mutex);
 }
 
@@ -956,8 +961,8 @@ static int rtsx_pci_init_hw(struct rtsx_pcr *pcr)
 	/* Reset delink mode */
 	rtsx_pci_add_cmd(pcr, WRITE_REG_CMD, CHANGE_LINK_STATE, 0x0A, 0);
 	/* Card driving select */
-	rtsx_pci_add_cmd(pcr, WRITE_REG_CMD, SD30_DRIVE_SEL,
-			0x07, DRIVER_TYPE_D);
+	rtsx_pci_add_cmd(pcr, WRITE_REG_CMD, CARD_DRIVE_SEL,
+			0xFF, pcr->card_drive_sel);
 	/* Enable SSC Clock */
 	rtsx_pci_add_cmd(pcr, WRITE_REG_CMD, SSC_CTL1,
 			0xFF, SSC_8X_EN | SSC_SEL_4M);
@@ -989,6 +994,8 @@ static int rtsx_pci_init_hw(struct rtsx_pcr *pcr)
 	if (err < 0)
 		return err;
 
+	rtsx_pci_write_config_byte(pcr, LCTLR, 0);
+
 	/* Enable clk_request_n to enable clock power management */
 	rtsx_pci_write_config_byte(pcr, 0x81, 1);
 	/* Enter L1 when host tx idle */
@@ -1053,6 +1060,18 @@ static int rtsx_pci_init_chip(struct rtsx_pcr *pcr)
 	if (!pcr->slots)
 		return -ENOMEM;
 
+	if (pcr->ops->init_settings)
+		pcr->ops->init_settings(pcr);
+
+	dev_dbg(&(pcr->pci->dev), "pcr->aspm_en = 0x%x\n", pcr->aspm_en);
+	dev_dbg(&(pcr->pci->dev), "pcr->sd30_drive_sel_1v8 = 0x%x\n",
+			pcr->sd30_drive_sel_1v8);
+	dev_dbg(&(pcr->pci->dev), "pcr->sd30_drive_sel_3v3 = 0x%x\n",
+			pcr->sd30_drive_sel_3v3);
+	dev_dbg(&(pcr->pci->dev), "pcr->card_drive_sel = 0x%x\n",
+			pcr->card_drive_sel);
+	dev_dbg(&(pcr->pci->dev), "pcr->flags = 0x%x\n", pcr->flags);
+
 	pcr->state = PDEV_STAT_IDLE;
 	err = rtsx_pci_init_hw(pcr);
 	if (err < 0) {
drivers/mfd/rtsx_pcr.h +30 -2
index c0cac7e..947e79b 100644
@@ -1,6 +1,6 @@
 /* Driver for Realtek PCI-Express card reader
  *
- * Copyright(c) 2009 Realtek Semiconductor Corp. All rights reserved.
+ * Copyright(c) 2009-2013 Realtek Semiconductor Corp. All rights reserved.
  *
  * This program is free software; you can redistribute it and/or modify it
  * under the terms of the GNU General Public License as published by the
@@ -17,7 +17,6 @@
  *
  * Author:
  *   Wei WANG <[email protected]>
- *   No. 450, Shenhu Road, Suzhou Industry Park, Suzhou, China
  */
 
 #ifndef __RTSX_PCR_H
@@ -35,4 +34,33 @@ void rts5227_init_params(struct rtsx_pcr *pcr);
 void rts5249_init_params(struct rtsx_pcr *pcr);
 void rtl8411b_init_params(struct rtsx_pcr *pcr);
 
+static inline u8 map_sd_drive(int idx)
+{
+	u8 sd_drive[4] = {
+		0x01,	/* Type D */
+		0x02,	/* Type C */
+		0x05,	/* Type A */
+		0x03	/* Type B */
+	};
+
+	return sd_drive[idx];
+}
+
+#define rtsx_vendor_setting_valid(reg)		(!((reg) & 0x1000000))
+#define rts5209_vendor_setting1_valid(reg)	(!((reg) & 0x80))
+#define rts5209_vendor_setting2_valid(reg)	((reg) & 0x80)
+
+#define rtsx_reg_to_aspm(reg)			(((reg) >> 28) & 0x03)
+#define rtsx_reg_to_sd30_drive_sel_1v8(reg)	(((reg) >> 26) & 0x03)
+#define rtsx_reg_to_sd30_drive_sel_3v3(reg)	(((reg) >> 5) & 0x03)
+#define rtsx_reg_to_card_drive_sel(reg)		((((reg) >> 25) & 0x01) << 6)
+#define rtsx_reg_check_reverse_socket(reg)	((reg) & 0x4000)
+#define rts5209_reg_to_aspm(reg)		(((reg) >> 5) & 0x03)
+#define rts5209_reg_check_ms_pmos(reg)		(!((reg) & 0x08))
+#define rts5209_reg_to_sd30_drive_sel_1v8(reg)	(((reg) >> 3) & 0x07)
+#define rts5209_reg_to_sd30_drive_sel_3v3(reg)	((reg) & 0x07)
+#define rts5209_reg_to_card_drive_sel(reg)	((reg) >> 8)
+#define rtl8411_reg_to_sd30_drive_sel_3v3(reg)	(((reg) >> 5) & 0x07)
+#define rtl8411b_reg_to_sd30_drive_sel_3v3(reg)	((reg) & 0x03)
+
 #endif
include/linux/mfd/rtsx_common.h +1 -2
index 2b13970..443176e 100644
@@ -1,6 +1,6 @@
 /* Driver for Realtek driver-based card reader
  *
- * Copyright(c) 2009 Realtek Semiconductor Corp. All rights reserved.
+ * Copyright(c) 2009-2013 Realtek Semiconductor Corp. All rights reserved.
  *
  * This program is free software; you can redistribute it and/or modify it
  * under the terms of the GNU General Public License as published by the
@@ -17,7 +17,6 @@
  *
  * Author:
  *   Wei WANG <[email protected]>
- *   No. 450, Shenhu Road, Suzhou Industry Park, Suzhou, China
  */
 
 #ifndef __RTSX_COMMON_H
include/linux/mfd/rtsx_pci.h +18 -3
index 7a9f708..9101c5f 100644
@@ -1,6 +1,6 @@
 /* Driver for Realtek PCI-Express card reader
  *
- * Copyright(c) 2009 Realtek Semiconductor Corp. All rights reserved.
+ * Copyright(c) 2009-2013 Realtek Semiconductor Corp. All rights reserved.
  *
  * This program is free software; you can redistribute it and/or modify it
  * under the terms of the GNU General Public License as published by the
@@ -17,7 +17,6 @@
  *
  * Author:
  *   Wei WANG <[email protected]>
- *   No. 450, Shenhu Road, Suzhou Industry Park, Suzhou, China
  */
 
 #ifndef __RTSX_PCI_H
@@ -684,6 +683,8 @@
 
 #define DUMMY_REG_RESET_0		0xFE90
 
+#define AUTOLOAD_CFG_BASE		0xFF00
+
 /* Memory mapping */
 #define SRAM_BASE			0xE600
 #define RBUF_BASE			0xF400
@@ -726,6 +727,11 @@
 #define PHY_FLD4			0x1E
 #define PHY_DUM_REG			0x1F
 
+#define LCTLR				0x80
+#define PCR_SETTING_REG1		0x724
+#define PCR_SETTING_REG2		0x814
+#define PCR_SETTING_REG3		0x747
+
 #define rtsx_pci_init_cmd(pcr)		((pcr)->ci = 0)
 
 struct rtsx_pcr;
@@ -747,6 +753,7 @@ struct pcr_ops {
 						u8 voltage);
 	unsigned int	(*cd_deglitch)(struct rtsx_pcr *pcr);
 	int		(*conv_clk_and_div_n)(int clk, int dir);
+	void		(*init_settings)(struct rtsx_pcr *pcr);
 };
 
 enum PDEV_STAT  {PDEV_STAT_IDLE, PDEV_STAT_RUN};
@@ -788,7 +795,6 @@ struct rtsx_pcr {
 	struct completion		*finish_me;
 
 	unsigned int			cur_clock;
-	bool				ms_pmos;
 	bool				remove_pci;
 	bool				msi_en;
 
@@ -806,6 +812,15 @@ struct rtsx_pcr {
 #define IC_VER_D			3
 	u8				ic_version;
 
+	u8				sd30_drive_sel_1v8;
+	u8				sd30_drive_sel_3v3;
+	u8				card_drive_sel;
+	u8				aspm_en;
+
+#define PCR_MS_PMOS			(1 << 0)
+#define PCR_REVERSE_SOCKET		(1 << 1)
+	u32				flags;
+
 	const u32			*sd_pull_ctl_enable_tbl;
 	const u32			*sd_pull_ctl_disable_tbl;
 	const u32			*ms_pull_ctl_enable_tbl;
Signature · 1 line
1.7.9.5
#2 lore raw

Re: [PATCH v2 1/5] mfd:rtsx: Read vendor setting from config space

Much better. Thank you.

regards,
dan carpenter

#3 lore raw

Re: [PATCH v2 1/5] mfd:rtsx: Read vendor setting from config space

In reply to [email protected]

Hi Wei,

Quoted 13 lines · On Wed, Jul 17, 2013 at 04:09:51PM +0800, [email protected] wrote:
drivers/mfd/rtl8411.c +1 -1
index c436bf2..1fbb978 100644
@@ -1,6 +1,6 @@
 /* Driver for Realtek PCI-Express card reader
  *
- * Copyright(c) 2009 Realtek Semiconductor Corp. All rights reserved.
+ * Copyright(c) 2009-2013 Realtek Semiconductor Corp. All rights reserved.
  *
  * This program is free software; you can redistribute it and/or modify it
  * under the terms of the GNU General Public License as published by the

drivers/mfd/rtl8411.c line 21

Quoted 6 lines
drivers/mfd/rtl8411.c +1 -1
@@ -17,7 +17,7 @@
  *
  * Author:
  *   Wei WANG <[email protected]>
- *   No. 450, Shenhu Road, Suzhou Industry Park, Suzhou, China
+ *   Roger Tseng <[email protected]>
  */

Please do not mix actual code with copyright changes. Remove those chunks from this patch, and submit a separate patch for them.

Quoted 5 lines
drivers/mfd/rtl8411.c +0 -0
 #include <linux/module.h>
@@ -47,19 +47,70 @@ static int rtl8411b_is_qfn48(struct rtsx_pcr *pcr)
 		return 0;
 }

drivers/mfd/rtl8411.c static int rtl8411b_is_qfn48(struct rtsx_pcr *pcr) · line 58

Quoted 10 lines
drivers/mfd/rtl8411.c +9 -0
 
+static void rtl8411_init_settings(struct rtsx_pcr *pcr)
+{
+	u32 reg1;
+	u8 reg3;
+
+	rtsx_pci_read_config_dword(pcr, PCR_SETTING_REG1, &reg1);
+	dev_dbg(&(pcr->pci->dev), "Cfg 0x%x: 0x%x\n", PCR_SETTING_REG1, reg1);
+
+	if (rtsx_vendor_setting_valid(reg1)) {

A more readable construct would be:

if (!rtsx_vendor_setting_valid(reg1))

	return;

pcr->aspm_en = rtsx_reg_to_aspm(reg1);
[...]

drivers/mfd/rtl8411.c void rtl8411_init_params(struct rtsx_pcr *pcr) · line 445

Quoted 9 lines
drivers/mfd/rtl8411.c +5 -0
@@ -385,6 +438,12 @@ void rtl8411_init_params(struct rtsx_pcr *pcr)
 	pcr->num_slots = 2;
 	pcr->ops = &rtl8411_pcr_ops;
 
+	pcr->flags = 0;
+	pcr->card_drive_sel = 0x55;
+	pcr->sd30_drive_sel_1v8 = 0x03;
+	pcr->sd30_drive_sel_3v3 = 0x01;
+	pcr->aspm_en = 0x02;

Those values seem to be repeated for many SKUs, could we please have a definition instead of hardcoded values ?

drivers/mfd/rtl8411.c struct pcr_ops { · line 756

Quoted 5 lines
drivers/mfd/rtl8411.c +1 -0
@@ -747,6 +753,7 @@ struct pcr_ops {
 						u8 voltage);
 	unsigned int	(*cd_deglitch)(struct rtsx_pcr *pcr);
 	int		(*conv_clk_and_div_n)(int clk, int dir);
+	void		(*init_settings)(struct rtsx_pcr *pcr);

init_settings is a bit too generic I believe. What you're doing is fetching vendor settings, so what about fetch_vendor_settings instead ?

Cheers,
Samuel.

Signature · 2 lines
Intel Open Source Technology Centre
http://oss.intel.com/
#4 lore raw

PATCH v2 2/5 mfd:rtsx: Add shutdown callback in rtsx_pci_driver

In reply to [email protected]

From: Wei WANG <[email protected]>

Some actions to clear power state should be handled in .shutdown callback in rtsx_pci_driver. This patch adopts the following measures to catch this goal:
1. Add a function rtsx_pci_power_off to abstract the common ops in .shutdown and .suspend
2. Add pcr->ops->force_power_down to fulfill the individual action for each reader model

---
 drivers/mfd/rtl8411.c        |    7 +++++++
 drivers/mfd/rts5209.c        |    6 ++++++
 drivers/mfd/rts5227.c        |   11 +++++++++++
 drivers/mfd/rts5229.c        |    6 ++++++
 drivers/mfd/rts5249.c        |   11 +++++++++++
 drivers/mfd/rtsx_pcr.c       |   43 ++++++++++++++++++++++++++++++++----------
 include/linux/mfd/rtsx_pci.h |   10 ++++++++++
 7 files changed, 84 insertions(+), 10 deletions(-)
drivers/mfd/rtl8411.c +7 -0
index 1fbb978..80c6fbc 100644
@@ -86,6 +86,11 @@ static void rtl8411b_init_settings(struct rtsx_pcr *pcr)
 	}
 }
 
+static void rtl8411_force_power_down(struct rtsx_pcr *pcr)
+{
+	rtsx_pci_write_register(pcr, FPDCTL, 0x07, 0x07);
+}
+
 static int rtl8411_extra_init_hw(struct rtsx_pcr *pcr)
 {
 	rtsx_pci_init_cmd(pcr);
@@ -285,6 +290,7 @@ static const struct pcr_ops rtl8411_pcr_ops = {
 	.switch_output_voltage = rtl8411_switch_output_voltage,
 	.cd_deglitch = rtl8411_cd_deglitch,
 	.conv_clk_and_div_n = rtl8411_conv_clk_and_div_n,
+	.force_power_down = rtl8411_force_power_down,
 };
 
 static const struct pcr_ops rtl8411b_pcr_ops = {
@@ -300,6 +306,7 @@ static const struct pcr_ops rtl8411b_pcr_ops = {
 	.switch_output_voltage = rtl8411_switch_output_voltage,
 	.cd_deglitch = rtl8411_cd_deglitch,
 	.conv_clk_and_div_n = rtl8411_conv_clk_and_div_n,
+	.force_power_down = rtl8411_force_power_down,
 };
 
 /* SD Pull Control Enable:
drivers/mfd/rts5209.c +6 -0
index 99e0ee2..524a5c5 100644
@@ -58,6 +58,11 @@ static void rts5209_init_settings(struct rtsx_pcr *pcr)
 	}
 }
 
+static void rts5209_force_power_down(struct rtsx_pcr *pcr)
+{
+	rtsx_pci_write_register(pcr, FPDCTL, 0x07, 0x07);
+}
+
 static int rts5209_extra_init_hw(struct rtsx_pcr *pcr)
 {
 	rtsx_pci_init_cmd(pcr);
@@ -196,6 +201,7 @@ static const struct pcr_ops rts5209_pcr_ops = {
 	.switch_output_voltage = rts5209_switch_output_voltage,
 	.cd_deglitch = NULL,
 	.conv_clk_and_div_n = NULL,
+	.force_power_down = rts5209_force_power_down,
 };
 
 /* SD Pull Control Enable:
drivers/mfd/rts5227.c +11 -0
index 6159f7a..fd95ab4 100644
@@ -82,6 +82,16 @@ static void rts5227_init_settings(struct rtsx_pcr *pcr)
 	}
 }
 
+static void rts5227_force_power_down(struct rtsx_pcr *pcr)
+{
+	/* Set relink_time to 0 */
+	rtsx_pci_write_register(pcr, AUTOLOAD_CFG_BASE + 1, 0xFF, 0);
+	rtsx_pci_write_register(pcr, AUTOLOAD_CFG_BASE + 2, 0xFF, 0);
+	rtsx_pci_write_register(pcr, AUTOLOAD_CFG_BASE + 3, 0x01, 0);
+
+	rtsx_pci_write_register(pcr, FPDCTL, 0x03, 0x03);
+}
+
 static int rts5227_extra_init_hw(struct rtsx_pcr *pcr)
 {
 	u16 cap;
@@ -217,6 +227,7 @@ static const struct pcr_ops rts5227_pcr_ops = {
 	.switch_output_voltage = rts5227_switch_output_voltage,
 	.cd_deglitch = NULL,
 	.conv_clk_and_div_n = NULL,
+	.force_power_down = rts5227_force_power_down,
 };
 
 /* SD Pull Control Enable:
drivers/mfd/rts5229.c +6 -0
index 9a3edfd..b283511 100644
@@ -55,6 +55,11 @@ static void rts5229_init_settings(struct rtsx_pcr *pcr)
 	}
 }
 
+static void rts5229_force_power_down(struct rtsx_pcr *pcr)
+{
+	rtsx_pci_write_register(pcr, FPDCTL, 0x03, 0x03);
+}
+
 static int rts5229_extra_init_hw(struct rtsx_pcr *pcr)
 {
 	rtsx_pci_init_cmd(pcr);
@@ -178,6 +183,7 @@ static const struct pcr_ops rts5229_pcr_ops = {
 	.switch_output_voltage = rts5229_switch_output_voltage,
 	.cd_deglitch = NULL,
 	.conv_clk_and_div_n = NULL,
+	.force_power_down = rts5229_force_power_down,
 };
 
 /* SD Pull Control Enable:
drivers/mfd/rts5249.c +11 -0
index 277b2dd..066d6ff 100644
@@ -89,6 +89,16 @@ static void rts5249_init_settings(struct rtsx_pcr *pcr)
 	}
 }
 
+static void rts5249_force_power_down(struct rtsx_pcr *pcr)
+{
+	/* Set relink_time to 0 */
+	rtsx_pci_write_register(pcr, AUTOLOAD_CFG_BASE + 1, 0xFF, 0);
+	rtsx_pci_write_register(pcr, AUTOLOAD_CFG_BASE + 2, 0xFF, 0);
+	rtsx_pci_write_register(pcr, AUTOLOAD_CFG_BASE + 3, 0x01, 0);
+
+	rtsx_pci_write_register(pcr, FPDCTL, 0x03, 0x03);
+}
+
 static int rts5249_extra_init_hw(struct rtsx_pcr *pcr)
 {
 	rtsx_pci_init_cmd(pcr);
@@ -218,6 +228,7 @@ static const struct pcr_ops rts5249_pcr_ops = {
 	.card_power_on = rts5249_card_power_on,
 	.card_power_off = rts5249_card_power_off,
 	.switch_output_voltage = rts5249_switch_output_voltage,
+	.force_power_down = rts5249_force_power_down,
 };
 
 /* SD Pull Control Enable:
drivers/mfd/rtsx_pcr.c +33 -10

83 lines not on this page · raw message

include/linux/mfd/rtsx_pci.h +10 -0
index 9101c5f..41d10e9 100644
@@ -520,6 +520,10 @@
 #define SAMPLE_VAR_CLK0			(0x01 << 4)
 #define SAMPLE_VAR_CLK1			(0x02 << 4)
 
+/* HOST_SLEEP_STATE */
+#define HOST_ENTER_S1			1
+#define HOST_ENTER_S3			2
+
 #define MS_CFG				0xFD40
 #define MS_TPC				0xFD41
 #define MS_TRANS_CFG			0xFD42
@@ -685,6 +689,11 @@
 
 #define AUTOLOAD_CFG_BASE		0xFF00
 
+#define PM_CTRL1			0xFF44
+#define PM_CTRL2			0xFF45
+#define PM_CTRL3			0xFF46
+#define PM_CTRL4			0xFF47
+
 /* Memory mapping */
 #define SRAM_BASE			0xE600
 #define RBUF_BASE			0xF400
@@ -754,6 +763,7 @@ struct pcr_ops {
 	unsigned int	(*cd_deglitch)(struct rtsx_pcr *pcr);
 	int		(*conv_clk_and_div_n)(int clk, int dir);
 	void		(*init_settings)(struct rtsx_pcr *pcr);
+	void		(*force_power_down)(struct rtsx_pcr *pcr);
 };
 
 enum PDEV_STAT  {PDEV_STAT_IDLE, PDEV_STAT_RUN};
Signature · 1 line
1.7.9.5
#5 lore raw

PATCH v2 3/5 mfd:rtsx: Move some actions from rtsx_pci_init_hw to individual extra_init_hw

In reply to [email protected]

From: Wei WANG <[email protected]>

These actions are individual for each reader model, so should be put in extra_init_hw instead of rtsx_pci_init_hw.

---
 drivers/mfd/rts5209.c  |    4 ++++
 drivers/mfd/rts5227.c  |    2 ++
 drivers/mfd/rts5229.c  |    4 ++++
 drivers/mfd/rts5249.c  |    2 ++
 drivers/mfd/rtsx_pcr.c |    4 ----
 5 files changed, 12 insertions(+), 4 deletions(-)
drivers/mfd/rts5209.c +4 -0
index 524a5c5..e2ee30e 100644
@@ -69,6 +69,10 @@ static int rts5209_extra_init_hw(struct rtsx_pcr *pcr)
 
 	/* Turn off LED */
 	rtsx_pci_add_cmd(pcr, WRITE_REG_CMD, CARD_GPIO, 0xFF, 0x03);
+	/* Reset ASPM state to default value */
+	rtsx_pci_add_cmd(pcr, WRITE_REG_CMD, ASPM_FORCE_CTL, 0x3F, 0);
+	/* Force CLKREQ# PIN to drive 0 to request clock */
+	rtsx_pci_add_cmd(pcr, WRITE_REG_CMD, PETXCFG, 0x08, 0x08);
 	/* Configure GPIO as output */
 	rtsx_pci_add_cmd(pcr, WRITE_REG_CMD, CARD_GPIO_DIR, 0xFF, 0x03);
 	/* Configure driving */
drivers/mfd/rts5227.c +2 -0
index fd95ab4..c931018 100644
@@ -100,6 +100,8 @@ static int rts5227_extra_init_hw(struct rtsx_pcr *pcr)
 
 	/* Configure GPIO as output */
 	rtsx_pci_add_cmd(pcr, WRITE_REG_CMD, GPIO_CTL, 0x02, 0x02);
+	/* Reset ASPM state to default value */
+	rtsx_pci_add_cmd(pcr, WRITE_REG_CMD, ASPM_FORCE_CTL, 0x3F, 0);
 	/* Switch LDO3318 source from DV33 to card_3v3 */
 	rtsx_pci_add_cmd(pcr, WRITE_REG_CMD, LDO_PWR_SEL, 0x03, 0x00);
 	rtsx_pci_add_cmd(pcr, WRITE_REG_CMD, LDO_PWR_SEL, 0x03, 0x01);
drivers/mfd/rts5229.c +4 -0
index b283511..a91462d 100644
@@ -66,6 +66,10 @@ static int rts5229_extra_init_hw(struct rtsx_pcr *pcr)
 
 	/* Configure GPIO as output */
 	rtsx_pci_add_cmd(pcr, WRITE_REG_CMD, GPIO_CTL, 0x02, 0x02);
+	/* Reset ASPM state to default value */
+	rtsx_pci_add_cmd(pcr, WRITE_REG_CMD, ASPM_FORCE_CTL, 0x3F, 0);
+	/* Force CLKREQ# PIN to drive 0 to request clock */
+	rtsx_pci_add_cmd(pcr, WRITE_REG_CMD, PETXCFG, 0x08, 0x08);
 	/* Switch LDO3318 source from DV33 to card_3v3 */
 	rtsx_pci_add_cmd(pcr, WRITE_REG_CMD, LDO_PWR_SEL, 0x03, 0x00);
 	rtsx_pci_add_cmd(pcr, WRITE_REG_CMD, LDO_PWR_SEL, 0x03, 0x01);
drivers/mfd/rts5249.c +2 -0
index 066d6ff..f18bb27 100644
@@ -105,6 +105,8 @@ static int rts5249_extra_init_hw(struct rtsx_pcr *pcr)
 
 	/* Configure GPIO as output */
 	rtsx_pci_add_cmd(pcr, WRITE_REG_CMD, GPIO_CTL, 0x02, 0x02);
+	/* Reset ASPM state to default value */
+	rtsx_pci_add_cmd(pcr, WRITE_REG_CMD, ASPM_FORCE_CTL, 0x3F, 0);
 	/* Switch LDO3318 source from DV33 to card_3v3 */
 	rtsx_pci_add_cmd(pcr, WRITE_REG_CMD, LDO_PWR_SEL, 0x03, 0x00);
 	rtsx_pci_add_cmd(pcr, WRITE_REG_CMD, LDO_PWR_SEL, 0x03, 0x01);
drivers/mfd/rtsx_pcr.c +0 -4
index a178173..13e1c24 100644
@@ -971,8 +971,6 @@ static int rtsx_pci_init_hw(struct rtsx_pcr *pcr)
 	rtsx_pci_add_cmd(pcr, WRITE_REG_CMD, HOST_SLEEP_STATE, 0x03, 0x00);
 	/* Disable card clock */
 	rtsx_pci_add_cmd(pcr, WRITE_REG_CMD, CARD_CLK_EN, 0x1E, 0);
-	/* Reset ASPM state to default value */
-	rtsx_pci_add_cmd(pcr, WRITE_REG_CMD, ASPM_FORCE_CTL, 0x3F, 0);
 	/* Reset delink mode */
 	rtsx_pci_add_cmd(pcr, WRITE_REG_CMD, CHANGE_LINK_STATE, 0x0A, 0);
 	/* Card driving select */
@@ -1002,8 +1000,6 @@ static int rtsx_pci_init_hw(struct rtsx_pcr *pcr)
 	 *	0: ELBI interrupt flag[31:22] & [7:0] only can be write clear
 	 */
 	rtsx_pci_add_cmd(pcr, WRITE_REG_CMD, NFTS_TX_CTRL, 0x02, 0);
-	/* Force CLKREQ# PIN to drive 0 to request clock */
-	rtsx_pci_add_cmd(pcr, WRITE_REG_CMD, PETXCFG, 0x08, 0x08);
 
 	err = rtsx_pci_send_cmd(pcr, 100);
 	if (err < 0)
Signature · 1 line
1.7.9.5
#6 lore raw

PATCH v2 4/5 mfd:rtsx: Clear hardware PFM mode in rtl8411b

In reply to [email protected]

From: Wei WANG <[email protected]>

Clear hw_pfm_en to disable hardware PFM mode, to fix a bug that in some situation registers in 0xFDxx domain can't be accessed.

---
 drivers/mfd/rtl8411.c        |    2 ++
 include/linux/mfd/rtsx_pci.h |    1 +
 2 files changed, 3 insertions(+)
drivers/mfd/rtl8411.c +2 -0
index 80c6fbc..2bff119 100644
@@ -114,6 +114,8 @@ static int rtl8411b_extra_init_hw(struct rtsx_pcr *pcr)
 			0xFF, pcr->sd30_drive_sel_3v3);
 	rtsx_pci_add_cmd(pcr, WRITE_REG_CMD, CD_PAD_CTL,
 			CD_DISABLE_MASK | CD_AUTO_DISABLE, CD_ENABLE);
+	rtsx_pci_add_cmd(pcr, WRITE_REG_CMD, FUNC_FORCE_CTL,
+			0x06, 0x00);
 
 	return rtsx_pci_send_cmd(pcr, 100);
 }
include/linux/mfd/rtsx_pci.h +1 -0
index 41d10e9..9763859 100644
@@ -672,6 +672,7 @@
 #define PME_FORCE_CTL			0xFE56
 #define ASPM_FORCE_CTL			0xFE57
 #define PM_CLK_FORCE_CTL		0xFE58
+#define FUNC_FORCE_CTL			0xFE59
 #define PERST_GLITCH_WIDTH		0xFE5C
 #define CHANGE_LINK_STATE		0xFE5B
 #define RESET_LOAD_REG			0xFE5E
Signature · 1 line
1.7.9.5
#7 lore raw

PATCH v2 5/5 mfd:rtsx: Configure to enter a deeper power-saving mode in S3

In reply to [email protected]

From: Wei WANG <[email protected]>

Set a bit to enable rts5227 and rts5249 to enter a deeper internal power-saving mode in S3, and recover it after resuming.

---
 drivers/mfd/rtl8411.c        |    2 +-
 drivers/mfd/rts5209.c        |    2 +-
 drivers/mfd/rts5227.c        |    6 +++++-
 drivers/mfd/rts5229.c        |    2 +-
 drivers/mfd/rts5249.c        |    6 +++++-
 drivers/mfd/rtsx_pcr.c       |    2 +-
 include/linux/mfd/rtsx_pci.h |    5 ++---
 7 files changed, 16 insertions(+), 9 deletions(-)
drivers/mfd/rtl8411.c +1 -1
index 2bff119..bfe65f6 100644
@@ -86,7 +86,7 @@ static void rtl8411b_init_settings(struct rtsx_pcr *pcr)
 	}
 }
 
-static void rtl8411_force_power_down(struct rtsx_pcr *pcr)
+static void rtl8411_force_power_down(struct rtsx_pcr *pcr, u8 pm_state)
 {
 	rtsx_pci_write_register(pcr, FPDCTL, 0x07, 0x07);
 }
drivers/mfd/rts5209.c +1 -1
index e2ee30e..a5261f9 100644
@@ -58,7 +58,7 @@ static void rts5209_init_settings(struct rtsx_pcr *pcr)
 	}
 }
 
-static void rts5209_force_power_down(struct rtsx_pcr *pcr)
+static void rts5209_force_power_down(struct rtsx_pcr *pcr, u8 pm_state)
 {
 	rtsx_pci_write_register(pcr, FPDCTL, 0x07, 0x07);
 }
drivers/mfd/rts5227.c +5 -1
index c931018..4c7309c 100644
@@ -82,13 +82,16 @@ static void rts5227_init_settings(struct rtsx_pcr *pcr)
 	}
 }
 
-static void rts5227_force_power_down(struct rtsx_pcr *pcr)
+static void rts5227_force_power_down(struct rtsx_pcr *pcr, u8 pm_state)
 {
 	/* Set relink_time to 0 */
 	rtsx_pci_write_register(pcr, AUTOLOAD_CFG_BASE + 1, 0xFF, 0);
 	rtsx_pci_write_register(pcr, AUTOLOAD_CFG_BASE + 2, 0xFF, 0);
 	rtsx_pci_write_register(pcr, AUTOLOAD_CFG_BASE + 3, 0x01, 0);
 
+	if (pm_state == HOST_ENTER_S3)
+		rtsx_pci_write_register(pcr, PM_CTRL3, 0x10, 0x10);
+
 	rtsx_pci_write_register(pcr, FPDCTL, 0x03, 0x03);
 }
 
@@ -122,6 +125,7 @@ static int rts5227_extra_init_hw(struct rtsx_pcr *pcr)
 	else
 		rtsx_pci_add_cmd(pcr, WRITE_REG_CMD,
 				AUTOLOAD_CFG_BASE + 3, 0xB8, 0x88);
+	rtsx_pci_add_cmd(pcr, WRITE_REG_CMD, PM_CTRL3, 0x10, 0x00);
 
 	return rtsx_pci_send_cmd(pcr, 100);
 }
drivers/mfd/rts5229.c +1 -1
index a91462d..e8e34de 100644
@@ -55,7 +55,7 @@ static void rts5229_init_settings(struct rtsx_pcr *pcr)
 	}
 }
 
-static void rts5229_force_power_down(struct rtsx_pcr *pcr)
+static void rts5229_force_power_down(struct rtsx_pcr *pcr, u8 pm_state)
 {
 	rtsx_pci_write_register(pcr, FPDCTL, 0x03, 0x03);
 }
drivers/mfd/rts5249.c +5 -1
index f18bb27..205344d 100644
@@ -89,13 +89,16 @@ static void rts5249_init_settings(struct rtsx_pcr *pcr)
 	}
 }
 
-static void rts5249_force_power_down(struct rtsx_pcr *pcr)
+static void rts5249_force_power_down(struct rtsx_pcr *pcr, u8 pm_state)
 {
 	/* Set relink_time to 0 */
 	rtsx_pci_write_register(pcr, AUTOLOAD_CFG_BASE + 1, 0xFF, 0);
 	rtsx_pci_write_register(pcr, AUTOLOAD_CFG_BASE + 2, 0xFF, 0);
 	rtsx_pci_write_register(pcr, AUTOLOAD_CFG_BASE + 3, 0x01, 0);
 
+	if (pm_state == HOST_ENTER_S3)
+		rtsx_pci_write_register(pcr, PM_CTRL3, 0x10, 0x10);
+
 	rtsx_pci_write_register(pcr, FPDCTL, 0x03, 0x03);
 }
 
@@ -120,6 +123,7 @@ static int rts5249_extra_init_hw(struct rtsx_pcr *pcr)
 	else
 		rtsx_pci_add_cmd(pcr, WRITE_REG_CMD,
 				AUTOLOAD_CFG_BASE + 3, 0xB0, 0x80);
+	rtsx_pci_add_cmd(pcr, WRITE_REG_CMD, PM_CTRL3, 0x10, 0x00);
 
 	return rtsx_pci_send_cmd(pcr, 100);
 }
drivers/mfd/rtsx_pcr.c +1 -1
index 13e1c24..1d7cc2e 100644
@@ -938,7 +938,7 @@ static void rtsx_pci_power_off(struct rtsx_pcr *pcr, u8 pm_state)
 	rtsx_pci_write_register(pcr, HOST_SLEEP_STATE, 0x03, pm_state);
 
 	if (pcr->ops->force_power_down)
-		pcr->ops->force_power_down(pcr);
+		pcr->ops->force_power_down(pcr, pm_state);
 }
 
 static int rtsx_pci_init_hw(struct rtsx_pcr *pcr)
include/linux/mfd/rtsx_pci.h +2 -3
index 9763859..8deabc8 100644
@@ -24,8 +24,7 @@
 
 #include <linux/sched.h>
 #include <linux/pci.h>
-
-#include "rtsx_common.h"
+#include <linux/mfd/rtsx_common.h>
 
 #define MAX_RW_REG_CNT			1024
 
@@ -764,7 +763,7 @@ struct pcr_ops {
 	unsigned int	(*cd_deglitch)(struct rtsx_pcr *pcr);
 	int		(*conv_clk_and_div_n)(int clk, int dir);
 	void		(*init_settings)(struct rtsx_pcr *pcr);
-	void		(*force_power_down)(struct rtsx_pcr *pcr);
+	void		(*force_power_down)(struct rtsx_pcr *pcr, u8 pm_state);
 };
 
 enum PDEV_STAT  {PDEV_STAT_IDLE, PDEV_STAT_RUN};
Signature · 1 line
1.7.9.5