mfd: wm8994: Remove unneeded check for JACKDET
Subsystems (2)
PATCH 1/2 mfd: wm8994: Remove unneeded check for JACKDET
From: Mark Brown <[email protected]>
The jack detection code holds runtime PM references when required so there is no need for suspend to do any checks.
--- drivers/mfd/wm8994-core.c | 14 -------------- 1 file changed, 14 deletions(-)
drivers/mfd/wm8994-core.c +0 -14
@@ -245,20 +245,6 @@ static int wm8994_suspend(struct device *dev)break ; } -switch (wm8994->type) { -case WM1811 : - ret =wm8994_reg_read (wm8994,WM8994_ANTIPOP_2 ); -if (ret <0 ) { -dev_err (dev,"Failed to read jackdet: %d\n" , ret); - }else if (ret &WM1811_JACKDET_MODE_MASK ) { -dev_dbg (dev,"CODEC still active, ignoring suspend\n" ); -return 0 ; - } -break ; -default : -break ; - } -/* Disable LDO pulldowns while the device is suspended if we * don't know that something will be driving them. */ if (!wm8994->ldo_ena_always_driven)
Signature · 1 line
1.8.3.2
PATCH 2/2 mfd: wm8994: Remove check for active audio in runtime suspend
From: Mark Brown <[email protected]>
Since enabling VMID takes a runtime PM reference there is no need to suppress suspend when doing a runtime suspend. Similarly the digital inputs and outputs are DAPM widgets and therefore the ASoC core will be holding a reference for them.
This used to be required when integration with system suspend was being bodged.
--- drivers/mfd/wm8994-core.c | 30 +----------------------------- 1 file changed, 1 insertion(+), 29 deletions(-)
drivers/mfd/wm8994-core.c +1 -29
@@ -201,35 +201,7 @@ static int wm8994_suspend(struct device *dev)int ret;/* Don't actually go through with the suspend if the CODEC is -* still active (eg, for audio passthrough from CP. */ - ret =wm8994_reg_read (wm8994,WM8994_POWER_MANAGEMENT_1 ); -if (ret <0 ) { -dev_err (dev,"Failed to read power status: %d\n" , ret); - }else if (ret &WM8994_VMID_SEL_MASK ) { -dev_dbg (dev,"CODEC still active, ignoring suspend\n" ); -return 0 ; - } - - ret =wm8994_reg_read (wm8994,WM8994_POWER_MANAGEMENT_4 ); -if (ret <0 ) { -dev_err (dev,"Failed to read power status: %d\n" , ret); - }else if (ret & (WM8994_AIF2ADCL_ENA |WM8994_AIF2ADCR_ENA | -WM8994_AIF1ADC2L_ENA |WM8994_AIF1ADC2R_ENA | -WM8994_AIF1ADC1L_ENA |WM8994_AIF1ADC1R_ENA )) { -dev_dbg (dev,"CODEC still active, ignoring suspend\n" ); -return 0 ; - } - - ret =wm8994_reg_read (wm8994,WM8994_POWER_MANAGEMENT_5 ); -if (ret <0 ) { -dev_err (dev,"Failed to read power status: %d\n" , ret); - }else if (ret & (WM8994_AIF2DACL_ENA |WM8994_AIF2DACR_ENA | -WM8994_AIF1DAC2L_ENA |WM8994_AIF1DAC2R_ENA | -WM8994_AIF1DAC1L_ENA |WM8994_AIF1DAC1R_ENA )) { -dev_dbg (dev,"CODEC still active, ignoring suspend\n" ); -return 0 ; - } - +* still active for accessory detect. */ switch (wm8994->type) {case WM8958 :case WM1811 :
Signature · 1 line
1.8.3.2
drivers/mfd/wm8994-core.c
Quoted 11 lines · Mark Brown
From: Mark Brown <[email protected]>
The jack detection code holds runtime PM references when required so there is no need for suspend to do any checks.
Signed-off-by Mark Brown <[email protected]>--- drivers/mfd/wm8994-core.c | 14 -------------- 1 file changed, 14 deletions(-)drivers/mfd/wm8994-core.c +0
-0
Thanks for the clarification.
Both patches applied.
Signature · 4 lines
Lee Jones Linaro ST-Ericsson Landing Team Lead Linaro.org │ Open source software for ARM SoCs Follow Linaro: Facebook | Twitter | Blog