MBus DT binding: The return of PCIe

---
 drivers/memory/mvebu-devbus.c | 64 ++-----------------------------------------
 1 file changed, 2 insertions(+), 62 deletions(-)

drivers/memory/mvebu-devbus.c +2 ~~-62~~

index 978e8e3..94c9248 100644
@@ -208,16 +208,11 @@ static int mvebu_devbus_probe(struct platform_device *pdev)
 {
 	struct device *dev = &pdev->dev;
 	struct device_node *node = pdev->dev.of_node;
-	struct device_node *parent;
 	struct devbus *devbus;
 	struct resource *res;
 	struct clk *clk;
 	unsigned long rate;
-	const __be32 *ranges;
-	int err, cs;
-	int addr_cells, p_addr_cells, size_cells;
-	int ranges_len, tuple_len;
-	u32 base, size;
+	int err;
 
 	devbus = devm_kzalloc(&pdev->dev, sizeof(struct devbus), GFP_KERNEL);
 	if (!devbus)

@@ -248,68 +243,13 @@ static int mvebu_devbus_probe(struct platform_device *pdev)
 		return err;
 
 	/*
-	 * Allocate an address window for this device.
-	 * If the device probing fails, then we won't be able to
-	 * remove the allocated address decoding window.
-	 *
-	 * FIXME: This is only a temporary hack! We need to do this here
-	 * because we still don't have device tree bindings for mbus.
-	 * Once that support is added, we will declare these address windows
-	 * statically in the device tree, and remove the window configuration
-	 * from here.
-	 */
-
-	/*
-	 * Get the CS to choose the window string.
-	 * This is a bit hacky, but it will be removed once the
-	 * address windows are declared in the device tree.
-	 */
-	cs = (((unsigned long)devbus->base) % 0x400) / 8;
-
-	/*
-	 * Parse 'ranges' property to obtain a (base,size) window tuple.
-	 * This will be removed once the address windows
-	 * are declared in the device tree.
-	 */
-	parent = of_get_parent(node);
-	if (!parent)
-		return -EINVAL;
-
-	p_addr_cells = of_n_addr_cells(parent);
-	of_node_put(parent);
-
-	addr_cells = of_n_addr_cells(node);
-	size_cells = of_n_size_cells(node);
-	tuple_len = (p_addr_cells + addr_cells + size_cells) * sizeof(__be32);
-
-	ranges = of_get_property(node, "ranges", &ranges_len);
-	if (ranges == NULL || ranges_len != tuple_len)
-		return -EINVAL;
-
-	base = of_translate_address(node, ranges + addr_cells);
-	if (base == OF_BAD_ADDR)
-		return -EINVAL;
-	size = of_read_number(ranges + addr_cells + p_addr_cells, size_cells);
-
-	/*
-	 * Create an mbus address windows.
-	 * FIXME: Remove this, together with the above code, once the
-	 * address windows are declared in the device tree.
-	 */
-	err = mvebu_mbus_add_window(devbus_wins[cs], base, size);
-	if (err < 0)
-		return err;
-
-	/*
 	 * We need to create a child device explicitly from here to
 	 * guarantee that the child will be probed after the timing
 	 * parameters for the bus are written.
 	 */
 	err = of_platform_populate(node, NULL, NULL, dev);
-	if (err < 0) {
-		mvebu_mbus_del_window(base, size);
+	if (err < 0)
 		return err;
-	}
 
 	return 0;
 }

Signature · 1 line

1.8.1.5

Ezequiel Garcia

author

2013-07-15 14:57 UTC #2 lore raw

PATCH RESEND v7 2/22 bus: mvebu-mbus: Add new API for window creation

From: Thomas Petazzoni <[email protected]>

We add an API to create MBus address decoding windows from the target ID and attribute. This function will be used later and deprecate the current name based scheme.

---
 drivers/bus/mvebu-mbus.c | 33 +++++++++++++++++++++++++--------
 include/linux/mbus.h     |  6 ++++++
 2 files changed, 31 insertions(+), 8 deletions(-)

drivers/bus/mvebu-mbus.c +25 -8

index 33c6947..827468a 100644
@@ -748,6 +748,22 @@ static const struct of_device_id of_mvebu_mbus_ids[] = {
 /*
  * Public API of the driver
  */
+int mvebu_mbus_add_window_remap_by_id(unsigned int target,
+				      unsigned int attribute,
+				      phys_addr_t base, size_t size,
+				      phys_addr_t remap)
+{
+	struct mvebu_mbus_state *s = &mbus_state;
+
+	if (!mvebu_mbus_window_conflicts(s, base, size, target, attribute)) {
+		pr_err("cannot add window '%x:%x', conflicts with another window\n",
+		       target, attribute);
+		return -EINVAL;
+	}
+
+	return mvebu_mbus_alloc_window(s, base, size, remap, target, attribute);
+}
+
 int mvebu_mbus_add_window_remap_flags(const char *devname, phys_addr_t base,
 				      size_t size, phys_addr_t remap,
 				      unsigned int flags)

@@ -776,14 +792,8 @@ int mvebu_mbus_add_window_remap_flags(const char *devname, phys_addr_t base,
 	else if (flags == MVEBU_MBUS_PCI_WA)
 		attr |= 0x28;
 
-	if (!mvebu_mbus_window_conflicts(s, base, size, target, attr)) {
-		pr_err("cannot add window '%s', conflicts with another window\n",
-		       devname);
-		return -EINVAL;
-	}
-
-	return mvebu_mbus_alloc_window(s, base, size, remap, target, attr);
-
+	return mvebu_mbus_add_window_remap_by_id(target, attr, base,
+						 size, remap);
 }
 
 int mvebu_mbus_add_window(const char *devname, phys_addr_t base, size_t size)

@@ -792,6 +802,13 @@ int mvebu_mbus_add_window(const char *devname, phys_addr_t base, size_t size)
 						 MVEBU_MBUS_NO_REMAP, 0);
 }
 
+int mvebu_mbus_add_window_by_id(unsigned int target, unsigned int attribute,
+				phys_addr_t base, size_t size)
+{
+	return mvebu_mbus_add_window_remap_by_id(target, attribute, base,
+						 size, MVEBU_MBUS_NO_REMAP);
+}
+
 int mvebu_mbus_del_window(phys_addr_t base, size_t size)
 {
 	int win;

include/linux/mbus.h +6 -0

index dba482e..9245b66 100644
@@ -62,8 +62,14 @@ static inline const struct mbus_dram_target_info *mv_mbus_dram_info(void)
 int mvebu_mbus_add_window_remap_flags(const char *devname, phys_addr_t base,
 				      size_t size, phys_addr_t remap,
 				      unsigned int flags);
+int mvebu_mbus_add_window_remap_by_id(unsigned int target,
+				      unsigned int attribute,
+				      phys_addr_t base, size_t size,
+				      phys_addr_t remap);
 int mvebu_mbus_add_window(const char *devname, phys_addr_t base,
 			  size_t size);
+int mvebu_mbus_add_window_by_id(unsigned int target, unsigned int attribute,
+				phys_addr_t base, size_t size);
 int mvebu_mbus_del_window(phys_addr_t base, size_t size);
 int mvebu_mbus_init(const char *soc, phys_addr_t mbus_phys_base,
 		    size_t mbus_size, phys_addr_t sdram_phys_base,

Signature · 1 line

1.8.1.5

Ezequiel Garcia

author

2013-07-15 14:57 UTC #3 lore raw

PATCH RESEND v7 3/22 ARM: kirkwood: Move to ID based MBus window creation

From: Thomas Petazzoni <[email protected]>

With the introduction of the ID based MBus API, it's better to switch to use it instead of the current name based scheme.

This will allow to deprecate the name based API, once every user is removed.

---
 arch/arm/mach-kirkwood/common.c | 18 ++++++++++++++----
 arch/arm/mach-kirkwood/pcie.c   | 40 ++++++++++++++++++++++++----------------
 2 files changed, 38 insertions(+), 20 deletions(-)

arch/arm/mach-kirkwood/common.c +14 -4

index e9238b5..165e751 100644
@@ -37,6 +37,12 @@
 #include <linux/platform_data/dma-mv_xor.h>
 #include "common.h"
 
+/* These can go away once Kirkwood uses the mvebu-mbus DT binding */
+#define KIRKWOOD_MBUS_NAND_TARGET 0x01
+#define KIRKWOOD_MBUS_NAND_ATTR   0x2f
+#define KIRKWOOD_MBUS_SRAM_TARGET 0x03
+#define KIRKWOOD_MBUS_SRAM_ATTR   0x01
+
 /*****************************************************************************
  * I/O Address Mapping
  ****************************************************************************/

@@ -672,10 +678,14 @@ char * __init kirkwood_id(void)
 
 void __init kirkwood_setup_wins(void)
 {
-	mvebu_mbus_add_window("nand", KIRKWOOD_NAND_MEM_PHYS_BASE,
-			      KIRKWOOD_NAND_MEM_SIZE);
-	mvebu_mbus_add_window("sram", KIRKWOOD_SRAM_PHYS_BASE,
-			      KIRKWOOD_SRAM_SIZE);
+	mvebu_mbus_add_window_by_id(KIRKWOOD_MBUS_NAND_TARGET,
+				    KIRKWOOD_MBUS_NAND_ATTR,
+				    KIRKWOOD_NAND_MEM_PHYS_BASE,
+				    KIRKWOOD_NAND_MEM_SIZE);
+	mvebu_mbus_add_window_by_id(KIRKWOOD_MBUS_SRAM_TARGET,
+				    KIRKWOOD_MBUS_SRAM_ATTR,
+				    KIRKWOOD_SRAM_PHYS_BASE,
+				    KIRKWOOD_SRAM_SIZE);
 }
 
 void __init kirkwood_l2_init(void)

arch/arm/mach-kirkwood/pcie.c +24 ~~-16~~

index ddcb09f..12d86f3 100644
@@ -20,6 +20,16 @@
 #include <mach/bridge-regs.h>
 #include "common.h"
 
+/* These can go away once Kirkwood uses the mvebu-mbus DT binding */
+#define KIRKWOOD_MBUS_PCIE0_MEM_TARGET    0x4
+#define KIRKWOOD_MBUS_PCIE0_MEM_ATTR      0xe8
+#define KIRKWOOD_MBUS_PCIE0_IO_TARGET     0x4
+#define KIRKWOOD_MBUS_PCIE0_IO_ATTR       0xe0
+#define KIRKWOOD_MBUS_PCIE1_MEM_TARGET    0x4
+#define KIRKWOOD_MBUS_PCIE1_MEM_ATTR      0xd8
+#define KIRKWOOD_MBUS_PCIE1_IO_TARGET     0x4
+#define KIRKWOOD_MBUS_PCIE1_IO_ATTR       0xd0
+
 static void kirkwood_enable_pcie_clk(const char *port)
 {
 	struct clk *clk;

@@ -254,26 +264,24 @@ static void __init add_pcie_port(int index, void __iomem *base)
 
 void __init kirkwood_pcie_init(unsigned int portmask)
 {
-	mvebu_mbus_add_window_remap_flags("pcie0.0",
+	mvebu_mbus_add_window_remap_by_id(KIRKWOOD_MBUS_PCIE0_IO_TARGET,
+					  KIRKWOOD_MBUS_PCIE0_IO_ATTR,
 					  KIRKWOOD_PCIE_IO_PHYS_BASE,
 					  KIRKWOOD_PCIE_IO_SIZE,
-					  KIRKWOOD_PCIE_IO_BUS_BASE,
-					  MVEBU_MBUS_PCI_IO);
-	mvebu_mbus_add_window_remap_flags("pcie0.0",
-					  KIRKWOOD_PCIE_MEM_PHYS_BASE,
-					  KIRKWOOD_PCIE_MEM_SIZE,
-					  MVEBU_MBUS_NO_REMAP,
-					  MVEBU_MBUS_PCI_MEM);
-	mvebu_mbus_add_window_remap_flags("pcie1.0",
+					  KIRKWOOD_PCIE_IO_BUS_BASE);
+	mvebu_mbus_add_window_by_id(KIRKWOOD_MBUS_PCIE0_MEM_TARGET,
+				    KIRKWOOD_MBUS_PCIE0_MEM_ATTR,
+				    KIRKWOOD_PCIE_MEM_PHYS_BASE,
+				    KIRKWOOD_PCIE_MEM_SIZE);
+	mvebu_mbus_add_window_remap_by_id(KIRKWOOD_MBUS_PCIE1_IO_TARGET,
+					  KIRKWOOD_MBUS_PCIE1_IO_ATTR,
 					  KIRKWOOD_PCIE1_IO_PHYS_BASE,
 					  KIRKWOOD_PCIE1_IO_SIZE,
-					  KIRKWOOD_PCIE1_IO_BUS_BASE,
-					  MVEBU_MBUS_PCI_IO);
-	mvebu_mbus_add_window_remap_flags("pcie1.0",
-					  KIRKWOOD_PCIE1_MEM_PHYS_BASE,
-					  KIRKWOOD_PCIE1_MEM_SIZE,
-					  MVEBU_MBUS_NO_REMAP,
-					  MVEBU_MBUS_PCI_MEM);
+					  KIRKWOOD_PCIE1_IO_BUS_BASE);
+	mvebu_mbus_add_window_by_id(KIRKWOOD_MBUS_PCIE1_MEM_TARGET,
+				    KIRKWOOD_MBUS_PCIE1_MEM_ATTR,
+				    KIRKWOOD_PCIE1_MEM_PHYS_BASE,
+				    KIRKWOOD_PCIE1_MEM_SIZE);
 
 	vga_base = KIRKWOOD_PCIE_MEM_PHYS_BASE;

Signature · 1 line

1.8.1.5

Ezequiel Garcia

author

2013-07-15 14:57 UTC #4 lore raw

PATCH RESEND v7 4/22 ARM: mv78xx0: Move to ID based window creation

From: Thomas Petazzoni <[email protected]>

With the introduction of the ID based MBus API, it's better to switch to use it instead of the current name based scheme.

This will allow to deprecate the name based API, once every user is removed.

---
 arch/arm/mach-mv78xx0/pcie.c | 23 +++++++++++------------
 1 file changed, 11 insertions(+), 12 deletions(-)

arch/arm/mach-mv78xx0/pcie.c +11 ~~-12~~

index dc26a65..397afde 100644
@@ -18,6 +18,11 @@
 #include <mach/mv78xx0.h>
 #include "common.h"
 
+#define MV78XX0_MBUS_PCIE_MEM_TARGET(port,lane) ((port) ? 8 : 4)
+#define MV78XX0_MBUS_PCIE_MEM_ATTR(port,lane)   (0xf8 & ~(0x10 << (lane)))
+#define MV78XX0_MBUS_PCIE_IO_TARGET(port,lane)  ((port) ? 8 : 4)
+#define MV78XX0_MBUS_PCIE_IO_ATTR(port,lane)    (0xf0 & ~(0x10 << (lane)))
+
 struct pcie_port {
 	u8			maj;
 	u8			min;

@@ -71,7 +76,6 @@ static void __init mv78xx0_pcie_preinit(void)
 	start = MV78XX0_PCIE_MEM_PHYS_BASE;
 	for (i = 0; i < num_pcie_ports; i++) {
 		struct pcie_port *pp = pcie_port + i;
-		char winname[MVEBU_MBUS_MAX_WINNAME_SZ];
 
 		snprintf(pp->mem_space_name, sizeof(pp->mem_space_name),
 			"PCIe %d.%d MEM", pp->maj, pp->min);

@@ -85,17 +89,12 @@ static void __init mv78xx0_pcie_preinit(void)
 		if (request_resource(&iomem_resource, &pp->res))
 			panic("can't allocate PCIe MEM sub-space");
 
-		snprintf(winname, sizeof(winname), "pcie%d.%d",
-			 pp->maj, pp->min);
-
-		mvebu_mbus_add_window_remap_flags(winname,
-						  pp->res.start,
-						  resource_size(&pp->res),
-						  MVEBU_MBUS_NO_REMAP,
-						  MVEBU_MBUS_PCI_MEM);
-		mvebu_mbus_add_window_remap_flags(winname,
-						  i * SZ_64K, SZ_64K,
-						  0, MVEBU_MBUS_PCI_IO);
+		mvebu_mbus_add_window_by_id(MV78XX0_MBUS_PCIE_MEM_TARGET(pp->maj, pp->min),
+					    MV78XX0_MBUS_PCIE_MEM_ATTR(pp->maj, pp->min),
+					    pp->res.start, resource_size(&pp->res));
+		mvebu_mbus_add_window_remap_by_id(MV78XX0_MBUS_PCIE_IO_TARGET(pp->maj, pp->min),
+						  MV78XX0_MBUS_PCIE_IO_ATTR(pp->maj, pp->min),
+						  i * SZ_64K, SZ_64K, 0);
 	}
 }

Signature · 1 line

1.8.1.5

Ezequiel Garcia

author

2013-07-15 14:57 UTC #5 lore raw

PATCH RESEND v7 5/22 ARM: orion5x: Move to ID based window creation

From: Thomas Petazzoni <[email protected]>

With the introduction of the ID based MBus API, it's better to switch to use it instead of the current name based scheme.

This will allow to deprecate the name based API, once every user is removed.

---
 arch/arm/mach-orion5x/common.c                 | 36 ++++++++++++++------------
 arch/arm/mach-orion5x/common.h                 | 17 ++++++++++++
 arch/arm/mach-orion5x/d2net-setup.c            |  6 +++--
 arch/arm/mach-orion5x/db88f5281-setup.c        | 24 +++++++++++------
 arch/arm/mach-orion5x/dns323-setup.c           |  6 +++--
 arch/arm/mach-orion5x/edmini_v2-setup.c        |  6 +++--
 arch/arm/mach-orion5x/kurobox_pro-setup.c      | 12 ++++++---
 arch/arm/mach-orion5x/ls-chl-setup.c           |  6 +++--
 arch/arm/mach-orion5x/ls_hgl-setup.c           |  6 +++--
 arch/arm/mach-orion5x/lsmini-setup.c           |  6 +++--
 arch/arm/mach-orion5x/mss2-setup.c             |  6 +++--
 arch/arm/mach-orion5x/mv2120-setup.c           |  6 +++--
 arch/arm/mach-orion5x/net2big-setup.c          |  6 +++--
 arch/arm/mach-orion5x/pci.c                    |  9 +++----
 arch/arm/mach-orion5x/rd88f5181l-fxo-setup.c   |  6 +++--
 arch/arm/mach-orion5x/rd88f5181l-ge-setup.c    |  6 +++--
 arch/arm/mach-orion5x/rd88f5182-setup.c        | 13 ++++++----
 arch/arm/mach-orion5x/terastation_pro2-setup.c |  6 +++--
 arch/arm/mach-orion5x/ts209-setup.c            |  6 +++--
 arch/arm/mach-orion5x/ts409-setup.c            |  6 +++--
 arch/arm/mach-orion5x/wnr854t-setup.c          |  6 +++--
 arch/arm/mach-orion5x/wrt350n-v2-setup.c       |  6 +++--
 22 files changed, 137 insertions(+), 70 deletions(-)

arch/arm/mach-orion5x/common.c +20 ~~-16~~

index b41599f..91a5852 100644
@@ -174,8 +174,10 @@ void __init orion5x_xor_init(void)
  ****************************************************************************/
 static void __init orion5x_crypto_init(void)
 {
-	mvebu_mbus_add_window("sram", ORION5X_SRAM_PHYS_BASE,
-			      ORION5X_SRAM_SIZE);
+	mvebu_mbus_add_window_by_id(ORION_MBUS_SRAM_TARGET,
+				    ORION_MBUS_SRAM_ATTR,
+				    ORION5X_SRAM_PHYS_BASE,
+				    ORION5X_SRAM_SIZE);
 	orion_crypto_init(ORION5X_CRYPTO_PHYS_BASE, ORION5X_SRAM_PHYS_BASE,
 			  SZ_8K, IRQ_ORION5X_CESA);
 }

@@ -222,22 +224,24 @@ void orion5x_setup_wins(void)
 	 * The PCIe windows will no longer be statically allocated
 	 * here once Orion5x is migrated to the pci-mvebu driver.
 	 */
-	mvebu_mbus_add_window_remap_flags("pcie0.0", ORION5X_PCIE_IO_PHYS_BASE,
+	mvebu_mbus_add_window_remap_by_id(ORION_MBUS_PCIE_IO_TARGET,
+					  ORION_MBUS_PCIE_IO_ATTR,
+					  ORION5X_PCIE_IO_PHYS_BASE,
 					  ORION5X_PCIE_IO_SIZE,
-					  ORION5X_PCIE_IO_BUS_BASE,
-					  MVEBU_MBUS_PCI_IO);
-	mvebu_mbus_add_window_remap_flags("pcie0.0", ORION5X_PCIE_MEM_PHYS_BASE,
-					  ORION5X_PCIE_MEM_SIZE,
-					  MVEBU_MBUS_NO_REMAP,
-					  MVEBU_MBUS_PCI_MEM);
-	mvebu_mbus_add_window_remap_flags("pci0.0", ORION5X_PCI_IO_PHYS_BASE,
+					  ORION5X_PCIE_IO_BUS_BASE);
+	mvebu_mbus_add_window_by_id(ORION_MBUS_PCIE_MEM_TARGET,
+				    ORION_MBUS_PCIE_MEM_ATTR,
+				    ORION5X_PCIE_MEM_PHYS_BASE,
+				    ORION5X_PCIE_MEM_SIZE);
+	mvebu_mbus_add_window_remap_by_id(ORION_MBUS_PCI_IO_TARGET,
+					  ORION_MBUS_PCI_IO_ATTR,
+					  ORION5X_PCI_IO_PHYS_BASE,
 					  ORION5X_PCI_IO_SIZE,
-					  ORION5X_PCI_IO_BUS_BASE,
-					  MVEBU_MBUS_PCI_IO);
-	mvebu_mbus_add_window_remap_flags("pci0.0", ORION5X_PCI_MEM_PHYS_BASE,
-					  ORION5X_PCI_MEM_SIZE,
-					  MVEBU_MBUS_NO_REMAP,
-					  MVEBU_MBUS_PCI_MEM);
+					  ORION5X_PCI_IO_BUS_BASE);
+	mvebu_mbus_add_window_by_id(ORION_MBUS_PCI_MEM_TARGET,
+				    ORION_MBUS_PCI_MEM_ATTR,
+				    ORION5X_PCI_MEM_PHYS_BASE,
+				    ORION5X_PCI_MEM_SIZE);
 }
 
 int orion5x_tclk;

arch/arm/mach-orion5x/common.h +17 -0

index a909afb..f565f99 100644
@@ -7,6 +7,23 @@ struct dsa_platform_data;
 struct mv643xx_eth_platform_data;
 struct mv_sata_platform_data;
 
+#define ORION_MBUS_PCIE_MEM_TARGET    0x04
+#define ORION_MBUS_PCIE_MEM_ATTR      0x59
+#define ORION_MBUS_PCIE_IO_TARGET     0x04
+#define ORION_MBUS_PCIE_IO_ATTR       0x51
+#define ORION_MBUS_PCIE_WA_TARGET     0x04
+#define ORION_MBUS_PCIE_WA_ATTR       0x79
+#define ORION_MBUS_PCI_MEM_TARGET     0x03
+#define ORION_MBUS_PCI_MEM_ATTR       0x59
+#define ORION_MBUS_PCI_IO_TARGET      0x03
+#define ORION_MBUS_PCI_IO_ATTR        0x51
+#define ORION_MBUS_DEVBUS_BOOT_TARGET 0x01
+#define ORION_MBUS_DEVBUS_BOOT_ATTR   0x0f
+#define ORION_MBUS_DEVBUS_TARGET(cs)  0x01
+#define ORION_MBUS_DEVBUS_ATTR(cs)    (~(1 << cs))
+#define ORION_MBUS_SRAM_TARGET        0x00
+#define ORION_MBUS_SRAM_ATTR          0x00
+
 /*
  * Basic Orion init functions used early by machine-setup.
  */

arch/arm/mach-orion5x/d2net-setup.c +4 -2

index 16c88bb..8f68b74 100644
@@ -317,8 +317,10 @@ static void __init d2net_init(void)
 	d2net_sata_power_init();
 	orion5x_sata_init(&d2net_sata_data);
 
-	mvebu_mbus_add_window("devbus-boot", D2NET_NOR_BOOT_BASE,
-			      D2NET_NOR_BOOT_SIZE);
+	mvebu_mbus_add_window_by_id(ORION_MBUS_DEVBUS_BOOT_TARGET,
+				    ORION_MBUS_DEVBUS_BOOT_ATTR,
+				    D2NET_NOR_BOOT_BASE,
+				    D2NET_NOR_BOOT_SIZE);
 	platform_device_register(&d2net_nor_flash);
 
 	platform_device_register(&d2net_gpio_buttons);

arch/arm/mach-orion5x/db88f5281-setup.c +16 -8

index 4e1263d..4b2aefd 100644
@@ -340,19 +340,27 @@ static void __init db88f5281_init(void)
 	orion5x_uart0_init();
 	orion5x_uart1_init();
 
-	mvebu_mbus_add_window("devbus-boot", DB88F5281_NOR_BOOT_BASE,
-			      DB88F5281_NOR_BOOT_SIZE);
+	mvebu_mbus_add_window_by_id(ORION_MBUS_DEVBUS_BOOT_TARGET,
+				    ORION_MBUS_DEVBUS_BOOT_ATTR,
+				    DB88F5281_NOR_BOOT_BASE,
+				    DB88F5281_NOR_BOOT_SIZE);
 	platform_device_register(&db88f5281_boot_flash);
 
-	mvebu_mbus_add_window("devbus-cs0", DB88F5281_7SEG_BASE,
-			      DB88F5281_7SEG_SIZE);
+	mvebu_mbus_add_window_by_id(ORION_MBUS_DEVBUS_TARGET(0),
+				    ORION_MBUS_DEVBUS_ATTR(0),
+				    DB88F5281_7SEG_BASE,
+				    DB88F5281_7SEG_SIZE);
 
-	mvebu_mbus_add_window("devbus-cs1", DB88F5281_NOR_BASE,
-			      DB88F5281_NOR_SIZE);
+	mvebu_mbus_add_window_by_id(ORION_MBUS_DEVBUS_TARGET(1),
+				    ORION_MBUS_DEVBUS_ATTR(1),
+				    DB88F5281_NOR_BASE,
+				    DB88F5281_NOR_SIZE);
 	platform_device_register(&db88f5281_nor_flash);
 
-	mvebu_mbus_add_window("devbus-cs2", DB88F5281_NAND_BASE,
-			      DB88F5281_NAND_SIZE);
+	mvebu_mbus_add_window_by_id(ORION_MBUS_DEVBUS_TARGET(2),
+				    ORION_MBUS_DEVBUS_ATTR(2),
+				    DB88F5281_NAND_BASE,
+				    DB88F5281_NAND_SIZE);
 	platform_device_register(&db88f5281_nand_flash);
 
 	i2c_register_board_info(0, &db88f5281_i2c_rtc, 1);

arch/arm/mach-orion5x/dns323-setup.c +4 -2

index 9e6baf5..7097473 100644
@@ -611,8 +611,10 @@ static void __init dns323_init(void)
 	/* setup flash mapping
 	 * CS3 holds a 8 MB Spansion S29GL064M90TFIR4
 	 */
-	mvebu_mbus_add_window("devbus-boot", DNS323_NOR_BOOT_BASE,
-			      DNS323_NOR_BOOT_SIZE);
+	mvebu_mbus_add_window_by_id(ORION_MBUS_DEVBUS_BOOT_TARGET,
+				    ORION_MBUS_DEVBUS_BOOT_ATTR,
+				    DNS323_NOR_BOOT_BASE,
+				    DNS323_NOR_BOOT_SIZE);
 	platform_device_register(&dns323_nor_flash);
 
 	/* Sort out LEDs, Buttons and i2c devices */

arch/arm/mach-orion5x/edmini_v2-setup.c +4 -2

index 1476155..0fc33c5 100644
@@ -154,8 +154,10 @@ void __init edmini_v2_init(void)
 	orion5x_ehci0_init();
 	orion5x_eth_init(&edmini_v2_eth_data);
 
-	mvebu_mbus_add_window("devbus-boot", EDMINI_V2_NOR_BOOT_BASE,
-			      EDMINI_V2_NOR_BOOT_SIZE);
+	mvebu_mbus_add_window_by_id(ORION_MBUS_DEVBUS_BOOT_TARGET,
+				    ORION_MBUS_DEVBUS_BOOT_ATTR,
+				    EDMINI_V2_NOR_BOOT_BASE,
+				    EDMINI_V2_NOR_BOOT_SIZE);
 	platform_device_register(&edmini_v2_nor_flash);
 
 	pr_notice("edmini_v2: USB device port, flash write and power-off "

arch/arm/mach-orion5x/kurobox_pro-setup.c +8 -4

index aae10e4..fe6a48a 100644
@@ -359,13 +359,17 @@ static void __init kurobox_pro_init(void)
 	orion5x_uart1_init();
 	orion5x_xor_init();
 
-	mvebu_mbus_add_window("devbus-boot", KUROBOX_PRO_NOR_BOOT_BASE,
-			      KUROBOX_PRO_NOR_BOOT_SIZE);
+	mvebu_mbus_add_window_by_id(ORION_MBUS_DEVBUS_BOOT_TARGET,
+				    ORION_MBUS_DEVBUS_BOOT_ATTR,
+				    KUROBOX_PRO_NOR_BOOT_BASE,
+				    KUROBOX_PRO_NOR_BOOT_SIZE);
 	platform_device_register(&kurobox_pro_nor_flash);
 
 	if (machine_is_kurobox_pro()) {
-		mvebu_mbus_add_window("devbus-cs0", KUROBOX_PRO_NAND_BASE,
-				      KUROBOX_PRO_NAND_SIZE);
+		mvebu_mbus_add_window_by_id(ORION_MBUS_DEVBUS_TARGET(0),
+					    ORION_MBUS_DEVBUS_ATTR(0),
+					    KUROBOX_PRO_NAND_BASE,
+					    KUROBOX_PRO_NAND_SIZE);
 		platform_device_register(&kurobox_pro_nand_flash);
 	}

arch/arm/mach-orion5x/ls-chl-setup.c +4 -2

index 6234977..028ea03 100644
@@ -294,8 +294,10 @@ static void __init lschl_init(void)
 	orion5x_uart0_init();
 	orion5x_xor_init();
 
-	mvebu_mbus_add_window("devbus-boot", LSCHL_NOR_BOOT_BASE,
-			      LSCHL_NOR_BOOT_SIZE);
+	mvebu_mbus_add_window_by_id(ORION_MBUS_DEVBUS_BOOT_TARGET,
+				    ORION_MBUS_DEVBUS_BOOT_ATTR,
+				    LSCHL_NOR_BOOT_BASE,
+				    LSCHL_NOR_BOOT_SIZE);
 	platform_device_register(&lschl_nor_flash);
 
 	platform_device_register(&lschl_leds);

arch/arm/mach-orion5x/ls_hgl-setup.c +4 -2

index fe04c4b..32b7129 100644
@@ -243,8 +243,10 @@ static void __init ls_hgl_init(void)
 	orion5x_uart0_init();
 	orion5x_xor_init();
 
-	mvebu_mbus_add_window("devbus-boot", LS_HGL_NOR_BOOT_BASE,
-			      LS_HGL_NOR_BOOT_SIZE);
+	mvebu_mbus_add_window_by_id(ORION_MBUS_DEVBUS_BOOT_TARGET,
+				    ORION_MBUS_DEVBUS_BOOT_ATTR,
+				    LS_HGL_NOR_BOOT_BASE,
+				    LS_HGL_NOR_BOOT_SIZE);
 	platform_device_register(&ls_hgl_nor_flash);
 
 	platform_device_register(&ls_hgl_button_device);

arch/arm/mach-orion5x/lsmini-setup.c +4 -2

index ca4dbe9..a6493e7 100644
@@ -244,8 +244,10 @@ static void __init lsmini_init(void)
 	orion5x_uart0_init();
 	orion5x_xor_init();
 
-	mvebu_mbus_add_window("devbus-boot", LSMINI_NOR_BOOT_BASE,
-			      LSMINI_NOR_BOOT_SIZE);
+	mvebu_mbus_add_window_by_id(ORION_MBUS_DEVBUS_BOOT_TARGET,
+				    ORION_MBUS_DEVBUS_BOOT_ATTR,
+				    LSMINI_NOR_BOOT_BASE,
+				    LSMINI_NOR_BOOT_SIZE);
 	platform_device_register(&lsmini_nor_flash);
 
 	platform_device_register(&lsmini_button_device);

arch/arm/mach-orion5x/mss2-setup.c +4 -2

index 827acba..e105130 100644
@@ -241,8 +241,10 @@ static void __init mss2_init(void)
 	orion5x_uart0_init();
 	orion5x_xor_init();
 
-	mvebu_mbus_add_window("devbus-boot", MSS2_NOR_BOOT_BASE,
-			      MSS2_NOR_BOOT_SIZE);
+	mvebu_mbus_add_window_by_id(ORION_MBUS_DEVBUS_BOOT_TARGET,
+				    ORION_MBUS_DEVBUS_BOOT_ATTR,
+				    MSS2_NOR_BOOT_BASE,
+				    MSS2_NOR_BOOT_SIZE);
 	platform_device_register(&mss2_nor_flash);
 
 	platform_device_register(&mss2_button_device);

arch/arm/mach-orion5x/mv2120-setup.c +4 -2

index 92600ae..e032f01 100644
@@ -204,8 +204,10 @@ static void __init mv2120_init(void)
 	orion5x_uart0_init();
 	orion5x_xor_init();
 
-	mvebu_mbus_add_window("devbus-boot", MV2120_NOR_BOOT_BASE,
-			      MV2120_NOR_BOOT_SIZE);
+	mvebu_mbus_add_window_by_id(ORION_MBUS_DEVBUS_BOOT_TARGET,
+				    ORION_MBUS_DEVBUS_BOOT_ATTR,
+				    MV2120_NOR_BOOT_BASE,
+				    MV2120_NOR_BOOT_SIZE);
 	platform_device_register(&mv2120_nor_flash);
 
 	platform_device_register(&mv2120_button_device);

arch/arm/mach-orion5x/net2big-setup.c +4 -2

index dd0641a..ba73dc7 100644
@@ -397,8 +397,10 @@ static void __init net2big_init(void)
 	net2big_sata_power_init();
 	orion5x_sata_init(&net2big_sata_data);
 
-	mvebu_mbus_add_window("devbus-boot", NET2BIG_NOR_BOOT_BASE,
-			      NET2BIG_NOR_BOOT_SIZE);
+	mvebu_mbus_add_window_by_id(ORION_MBUS_DEVBUS_BOOT_TARGET,
+				    ORION_MBUS_DEVBUS_BOOT_ATTR,
+				    NET2BIG_NOR_BOOT_BASE,
+				    NET2BIG_NOR_BOOT_SIZE);
 	platform_device_register(&net2big_nor_flash);
 
 	platform_device_register(&net2big_gpio_buttons);

arch/arm/mach-orion5x/pci.c +4 -5

index 5033680..7fab670 100644
@@ -157,11 +157,10 @@ static int __init pcie_setup(struct pci_sys_data *sys)
 	if (dev == MV88F5181_DEV_ID || dev == MV88F5182_DEV_ID) {
 		printk(KERN_NOTICE "Applying Orion-1/Orion-NAS PCIe config "
 				   "read transaction workaround\n");
-		mvebu_mbus_add_window_remap_flags("pcie0.0",
-						  ORION5X_PCIE_WA_PHYS_BASE,
-						  ORION5X_PCIE_WA_SIZE,
-						  MVEBU_MBUS_NO_REMAP,
-						  MVEBU_MBUS_PCI_WA);
+		mvebu_mbus_add_window_by_id(ORION_MBUS_PCIE_WA_TARGET,
+					    ORION_MBUS_PCIE_WA_ATTR,
+					    ORION5X_PCIE_WA_PHYS_BASE,
+					    ORION5X_PCIE_WA_SIZE);
 		pcie_ops.read = pcie_rd_conf_wa;
 	}

arch/arm/mach-orion5x/rd88f5181l-fxo-setup.c +4 -2

index 1c4498b..213b3e1 100644
@@ -123,8 +123,10 @@ static void __init rd88f5181l_fxo_init(void)
 	orion5x_eth_switch_init(&rd88f5181l_fxo_switch_plat_data, NO_IRQ);
 	orion5x_uart0_init();
 
-	mvebu_mbus_add_window("devbus-boot", RD88F5181L_FXO_NOR_BOOT_BASE,
-			      RD88F5181L_FXO_NOR_BOOT_SIZE);
+	mvebu_mbus_add_window_by_id(ORION_MBUS_DEVBUS_BOOT_TARGET,
+				    ORION_MBUS_DEVBUS_BOOT_ATTR,
+				    RD88F5181L_FXO_NOR_BOOT_BASE,
+				    RD88F5181L_FXO_NOR_BOOT_SIZE);
 	platform_device_register(&rd88f5181l_fxo_nor_boot_flash);
 }

arch/arm/mach-orion5x/rd88f5181l-ge-setup.c +4 -2

index adabe34..594800e 100644
@@ -130,8 +130,10 @@ static void __init rd88f5181l_ge_init(void)
 	orion5x_i2c_init();
 	orion5x_uart0_init();
 
-	mvebu_mbus_add_window("devbus-boot", RD88F5181L_GE_NOR_BOOT_BASE,
-			      RD88F5181L_GE_NOR_BOOT_SIZE);
+	mvebu_mbus_add_window_by_id(ORION_MBUS_DEVBUS_BOOT_TARGET,
+				    ORION_MBUS_DEVBUS_BOOT_ATTR,
+				    RD88F5181L_GE_NOR_BOOT_BASE,
+				    RD88F5181L_GE_NOR_BOOT_SIZE);
 	platform_device_register(&rd88f5181l_ge_nor_boot_flash);
 
 	i2c_register_board_info(0, &rd88f5181l_ge_i2c_rtc, 1);

arch/arm/mach-orion5x/rd88f5182-setup.c +8 -5

index 66e77ec..b1cf684 100644
@@ -264,11 +264,14 @@ static void __init rd88f5182_init(void)
 	orion5x_uart0_init();
 	orion5x_xor_init();
 
-	mvebu_mbus_add_window("devbus-boot", RD88F5182_NOR_BOOT_BASE,
-			      RD88F5182_NOR_BOOT_SIZE);
-
-	mvebu_mbus_add_window("devbus-cs1", RD88F5182_NOR_BASE,
-			      RD88F5182_NOR_SIZE);
+	mvebu_mbus_add_window_by_id(ORION_MBUS_DEVBUS_BOOT_TARGET,
+				    ORION_MBUS_DEVBUS_BOOT_ATTR,
+				    RD88F5182_NOR_BOOT_BASE,
+				    RD88F5182_NOR_BOOT_SIZE);
+	mvebu_mbus_add_window_by_id(ORION_MBUS_DEVBUS_TARGET(1),
+				    ORION_MBUS_DEVBUS_ATTR(1),
+				    RD88F5182_NOR_BASE,
+				    RD88F5182_NOR_SIZE);
 	platform_device_register(&rd88f5182_nor_flash);
 	platform_device_register(&rd88f5182_gpio_leds);

arch/arm/mach-orion5x/terastation_pro2-setup.c +4 -2

index a0bfa53..7e90648 100644
@@ -329,8 +329,10 @@ static void __init tsp2_init(void)
 	/*
 	 * Configure peripherals.
 	 */
-	mvebu_mbus_add_window("devbus-boot", TSP2_NOR_BOOT_BASE,
-			      TSP2_NOR_BOOT_SIZE);
+	mvebu_mbus_add_window_by_id(ORION_MBUS_DEVBUS_BOOT_TARGET,
+				    ORION_MBUS_DEVBUS_BOOT_ATTR,
+				    TSP2_NOR_BOOT_BASE,
+				    TSP2_NOR_BOOT_SIZE);
 	platform_device_register(&tsp2_nor_flash);
 
 	orion5x_ehci0_init();

arch/arm/mach-orion5x/ts209-setup.c +4 -2

index 80174f0..e90c061 100644
@@ -286,8 +286,10 @@ static void __init qnap_ts209_init(void)
 	/*
 	 * Configure peripherals.
 	 */
-	mvebu_mbus_add_window("devbus-boot", QNAP_TS209_NOR_BOOT_BASE,
-			      QNAP_TS209_NOR_BOOT_SIZE);
+	mvebu_mbus_add_window_by_id(ORION_MBUS_DEVBUS_BOOT_TARGET,
+				    ORION_MBUS_DEVBUS_BOOT_ATTR,
+				    QNAP_TS209_NOR_BOOT_BASE,
+				    QNAP_TS209_NOR_BOOT_SIZE);
 	platform_device_register(&qnap_ts209_nor_flash);
 
 	orion5x_ehci0_init();

arch/arm/mach-orion5x/ts409-setup.c +4 -2

index 9259279..5c079d3 100644
@@ -277,8 +277,10 @@ static void __init qnap_ts409_init(void)
 	/*
 	 * Configure peripherals.
 	 */
-	mvebu_mbus_add_window("devbus-boot", QNAP_TS409_NOR_BOOT_BASE,
-			      QNAP_TS409_NOR_BOOT_SIZE);
+	mvebu_mbus_add_window_by_id(ORION_MBUS_DEVBUS_BOOT_TARGET,
+				    ORION_MBUS_DEVBUS_BOOT_ATTR,
+				    QNAP_TS409_NOR_BOOT_BASE,
+				    QNAP_TS409_NOR_BOOT_SIZE);
 	platform_device_register(&qnap_ts409_nor_flash);
 
 	orion5x_ehci0_init();

arch/arm/mach-orion5x/wnr854t-setup.c +4 -2

index 6b84863..80a56ee 100644
@@ -127,8 +127,10 @@ static void __init wnr854t_init(void)
 	orion5x_eth_switch_init(&wnr854t_switch_plat_data, NO_IRQ);
 	orion5x_uart0_init();
 
-	mvebu_mbus_add_window("devbus-boot", WNR854T_NOR_BOOT_BASE,
-			      WNR854T_NOR_BOOT_SIZE);
+	mvebu_mbus_add_window_by_id(ORION_MBUS_DEVBUS_BOOT_TARGET,
+				    ORION_MBUS_DEVBUS_BOOT_ATTR,
+				    WNR854T_NOR_BOOT_BASE,
+				    WNR854T_NOR_BOOT_SIZE);
 	platform_device_register(&wnr854t_nor_flash);
 }

arch/arm/mach-orion5x/wrt350n-v2-setup.c +4 -2

index fae684b..670e30d 100644
@@ -213,8 +213,10 @@ static void __init wrt350n_v2_init(void)
 	orion5x_eth_switch_init(&wrt350n_v2_switch_plat_data, NO_IRQ);
 	orion5x_uart0_init();
 
-	mvebu_mbus_add_window("devbus-boot", WRT350N_V2_NOR_BOOT_BASE,
-			      WRT350N_V2_NOR_BOOT_SIZE);
+	mvebu_mbus_add_window_by_id(ORION_MBUS_DEVBUS_BOOT_TARGET,
+				    ORION_MBUS_DEVBUS_BOOT_ATTR,
+				    WRT350N_V2_NOR_BOOT_BASE,
+				    WRT350N_V2_NOR_BOOT_SIZE);
 	platform_device_register(&wrt350n_v2_nor_flash);
 	platform_device_register(&wrt350n_v2_leds);
 	platform_device_register(&wrt350n_v2_button_device);

Signature · 1 line

1.8.1.5

Ezequiel Garcia

author

2013-07-15 14:57 UTC #6 lore raw

PATCH RESEND v7 6/22 ARM: dove: Move to ID based window creation

From: Thomas Petazzoni <[email protected]>

With the introduction of the ID based MBus API, it's better to switch to use it instead of the current name based scheme.

This will allow to deprecate the name based API, once every user is removed.

---
 arch/arm/mach-dove/common.c | 68 ++++++++++++++++++++++++++++++---------------
 1 file changed, 45 insertions(+), 23 deletions(-)

arch/arm/mach-dove/common.c +45 ~~-23~~

index 00247c7..bc22056 100644
@@ -27,6 +27,22 @@
 #include <plat/time.h>
 #include "common.h"
 
+/* These can go away once Dove uses the mvebu-mbus DT binding */
+#define DOVE_MBUS_PCIE0_MEM_TARGET    0x4
+#define DOVE_MBUS_PCIE0_MEM_ATTR      0xe8
+#define DOVE_MBUS_PCIE0_IO_TARGET     0x4
+#define DOVE_MBUS_PCIE0_IO_ATTR       0xe0
+#define DOVE_MBUS_PCIE1_MEM_TARGET    0x8
+#define DOVE_MBUS_PCIE1_MEM_ATTR      0xe8
+#define DOVE_MBUS_PCIE1_IO_TARGET     0x8
+#define DOVE_MBUS_PCIE1_IO_ATTR       0xe0
+#define DOVE_MBUS_CESA_TARGET         0x3
+#define DOVE_MBUS_CESA_ATTR           0x1
+#define DOVE_MBUS_BOOTROM_TARGET      0x1
+#define DOVE_MBUS_BOOTROM_ATTR        0xfd
+#define DOVE_MBUS_SCRATCHPAD_TARGET   0xd
+#define DOVE_MBUS_SCRATCHPAD_ATTR     0x0
+
 /*****************************************************************************
  * I/O Address Mapping
  ****************************************************************************/

@@ -332,34 +348,40 @@ void __init dove_setup_cpu_wins(void)
 {
 	/*
 	 * The PCIe windows will no longer be statically allocated
-	 * here once Dove is migrated to the pci-mvebu driver.
+	 * here once Dove is migrated to the pci-mvebu driver. The
+	 * non-PCIe windows will no longer be created here once Dove
+	 * fully moves to DT.
 	 */
-	mvebu_mbus_add_window_remap_flags("pcie0.0",
+	mvebu_mbus_add_window_remap_by_id(DOVE_MBUS_PCIE0_IO_TARGET,
+					  DOVE_MBUS_PCIE0_IO_ATTR,
 					  DOVE_PCIE0_IO_PHYS_BASE,
 					  DOVE_PCIE0_IO_SIZE,
-					  DOVE_PCIE0_IO_BUS_BASE,
-					  MVEBU_MBUS_PCI_IO);
-	mvebu_mbus_add_window_remap_flags("pcie1.0",
+					  DOVE_PCIE0_IO_BUS_BASE);
+	mvebu_mbus_add_window_remap_by_id(DOVE_MBUS_PCIE1_IO_TARGET,
+					  DOVE_MBUS_PCIE1_IO_ATTR,
 					  DOVE_PCIE1_IO_PHYS_BASE,
 					  DOVE_PCIE1_IO_SIZE,
-					  DOVE_PCIE1_IO_BUS_BASE,
-					  MVEBU_MBUS_PCI_IO);
-	mvebu_mbus_add_window_remap_flags("pcie0.0",
-					  DOVE_PCIE0_MEM_PHYS_BASE,
-					  DOVE_PCIE0_MEM_SIZE,
-					  MVEBU_MBUS_NO_REMAP,
-					  MVEBU_MBUS_PCI_MEM);
-	mvebu_mbus_add_window_remap_flags("pcie1.0",
-					  DOVE_PCIE1_MEM_PHYS_BASE,
-					  DOVE_PCIE1_MEM_SIZE,
-					  MVEBU_MBUS_NO_REMAP,
-					  MVEBU_MBUS_PCI_MEM);
-	mvebu_mbus_add_window("cesa", DOVE_CESA_PHYS_BASE,
-			      DOVE_CESA_SIZE);
-	mvebu_mbus_add_window("bootrom", DOVE_BOOTROM_PHYS_BASE,
-			      DOVE_BOOTROM_SIZE);
-	mvebu_mbus_add_window("scratchpad", DOVE_SCRATCHPAD_PHYS_BASE,
-			      DOVE_SCRATCHPAD_SIZE);
+					  DOVE_PCIE1_IO_BUS_BASE);
+	mvebu_mbus_add_window_by_id(DOVE_MBUS_PCIE0_MEM_TARGET,
+				    DOVE_MBUS_PCIE0_MEM_ATTR,
+				    DOVE_PCIE0_MEM_PHYS_BASE,
+				    DOVE_PCIE0_MEM_SIZE);
+	mvebu_mbus_add_window_by_id(DOVE_MBUS_PCIE1_MEM_TARGET,
+				    DOVE_MBUS_PCIE1_MEM_ATTR,
+				    DOVE_PCIE1_MEM_PHYS_BASE,
+				    DOVE_PCIE1_MEM_SIZE);
+	mvebu_mbus_add_window_by_id(DOVE_MBUS_CESA_TARGET,
+				    DOVE_MBUS_CESA_ATTR,
+				    DOVE_CESA_PHYS_BASE,
+				    DOVE_CESA_SIZE);
+	mvebu_mbus_add_window_by_id(DOVE_MBUS_BOOTROM_TARGET,
+				    DOVE_MBUS_BOOTROM_ATTR,
+				    DOVE_BOOTROM_PHYS_BASE,
+				    DOVE_BOOTROM_SIZE);
+	mvebu_mbus_add_window_by_id(DOVE_MBUS_SCRATCHPAD_TARGET,
+				    DOVE_MBUS_SCRATCHPAD_ATTR,
+				    DOVE_SCRATCHPAD_PHYS_BASE,
+				    DOVE_SCRATCHPAD_SIZE);
 }
 
 void __init dove_init(void)

Signature · 1 line

1.8.1.5

Ezequiel Garcia

author

2013-07-15 14:57 UTC #7 lore raw

PATCH RESEND v7 7/22 bus: mvebu-mbus: Factor out initialization details

We introduce a common initialization function mvebu_mbus_common_init() that will be used by both legacy and device-tree initialization code. This patch is an intermediate step, which will allow to introduce the DT binding for this driver in a less intrusive way.

---
 drivers/bus/mvebu-mbus.c | 47 ++++++++++++++++++++++++++++++-----------------
 1 file changed, 30 insertions(+), 17 deletions(-)

drivers/bus/mvebu-mbus.c +30 ~~-17~~

index 827468a..1b17954 100644
@@ -847,26 +847,14 @@ static __init int mvebu_mbus_debugfs_init(void)
 }
 fs_initcall(mvebu_mbus_debugfs_init);
 
-int __init mvebu_mbus_init(const char *soc, phys_addr_t mbuswins_phys_base,
-			   size_t mbuswins_size,
-			   phys_addr_t sdramwins_phys_base,
-			   size_t sdramwins_size)
+static int __init mvebu_mbus_common_init(struct mvebu_mbus_state *mbus,
+					 phys_addr_t mbuswins_phys_base,
+					 size_t mbuswins_size,
+					 phys_addr_t sdramwins_phys_base,
+					 size_t sdramwins_size)
 {
-	struct mvebu_mbus_state *mbus = &mbus_state;
-	const struct of_device_id *of_id;
 	int win;
 
-	for (of_id = of_mvebu_mbus_ids; of_id->compatible; of_id++)
-		if (!strcmp(of_id->compatible, soc))
-			break;
-
-	if (!of_id->compatible) {
-		pr_err("could not find a matching SoC family\n");
-		return -ENODEV;
-	}
-
-	mbus->soc = of_id->data;
-
 	mbus->mbuswins_base = ioremap(mbuswins_phys_base, mbuswins_size);
 	if (!mbus->mbuswins_base)
 		return -ENOMEM;

@@ -887,3 +875,28 @@ int __init mvebu_mbus_init(const char *soc, phys_addr_t mbuswins_phys_base,
 
 	return 0;
 }
+
+int __init mvebu_mbus_init(const char *soc, phys_addr_t mbuswins_phys_base,
+			   size_t mbuswins_size,
+			   phys_addr_t sdramwins_phys_base,
+			   size_t sdramwins_size)
+{
+	const struct of_device_id *of_id;
+
+	for (of_id = of_mvebu_mbus_ids; of_id->compatible; of_id++)
+		if (!strcmp(of_id->compatible, soc))
+			break;
+
+	if (!of_id->compatible) {
+		pr_err("could not find a matching SoC family\n");
+		return -ENODEV;
+	}
+
+	mbus_state.soc = of_id->data;
+
+	return mvebu_mbus_common_init(&mbus_state,
+			mbuswins_phys_base,
+			mbuswins_size,
+			sdramwins_phys_base,
+			sdramwins_size);
+}

Signature · 1 line

1.8.1.5

Ezequiel Garcia

author

2013-07-15 14:57 UTC #8 lore raw

PATCH RESEND v7 8/22 bus: mvebu-mbus: Introduce device tree binding

This patch adds the most fundamental device-tree initialization. We only introduce what's required to be able to probe the mvebu-mbus driver from the DT. Follow-up patches will extend the device tree binding, allowing to describe static address decoding windows.

---
 drivers/bus/mvebu-mbus.c | 49 ++++++++++++++++++++++++++++++++++++++++++++++++
 include/linux/mbus.h     |  1 +
 2 files changed, 50 insertions(+)

drivers/bus/mvebu-mbus.c +49 -0

index 1b17954..44a07c4 100644
@@ -900,3 +900,52 @@ int __init mvebu_mbus_init(const char *soc, phys_addr_t mbuswins_phys_base,
 			sdramwins_phys_base,
 			sdramwins_size);
 }
+
+#ifdef CONFIG_OF
+int __init mvebu_mbus_dt_init(void)
+{
+	struct resource mbuswins_res, sdramwins_res;
+	struct device_node *np, *controller;
+	const struct of_device_id *of_id;
+	const __be32 *prop;
+	int ret;
+
+	np = of_find_matching_node(NULL, of_mvebu_mbus_ids);
+	if (!np) {
+		pr_err("could not find a matching SoC family\n");
+		return -ENODEV;
+	}
+
+	of_id = of_match_node(of_mvebu_mbus_ids, np);
+	mbus_state.soc = of_id->data;
+
+	prop = of_get_property(np, "controller", NULL);
+	if (!prop) {
+		pr_err("required 'controller' property missing\n");
+		return -EINVAL;
+	}
+
+	controller = of_find_node_by_phandle(be32_to_cpup(prop));
+	if (!controller) {
+		pr_err("could not find an 'mbus-controller' node\n");
+		return -ENODEV;
+	}
+
+	if (of_address_to_resource(controller, 0, &mbuswins_res)) {
+		pr_err("cannot get MBUS register address\n");
+		return -EINVAL;
+	}
+
+	if (of_address_to_resource(controller, 1, &sdramwins_res)) {
+		pr_err("cannot get SDRAM register address\n");
+		return -EINVAL;
+	}
+
+	ret = mvebu_mbus_common_init(&mbus_state,
+				     mbuswins_res.start,
+				     resource_size(&mbuswins_res),
+				     sdramwins_res.start,
+				     resource_size(&sdramwins_res));
+	return ret;
+}
+#endif

include/linux/mbus.h +1 -0

index 9245b66..eadefd6 100644
@@ -74,5 +74,6 @@ int mvebu_mbus_del_window(phys_addr_t base, size_t size);
 int mvebu_mbus_init(const char *soc, phys_addr_t mbus_phys_base,
 		    size_t mbus_size, phys_addr_t sdram_phys_base,
 		    size_t sdram_size);
+int mvebu_mbus_dt_init(void);
 
 #endif /* __LINUX_MBUS_H */

Signature · 1 line

1.8.1.5

Ezequiel Garcia

author

2013-07-15 14:57 UTC #9 lore raw

PATCH RESEND v7 9/22 bus: mvebu-mbus: Add static window allocation to the DT binding

This patch adds static window allocation to the device tree binding. Each first-child of the mbus-compatible node, with a suitable 'ranges' property, declaring an address translation, will trigger an address decoding window allocation.

---
 .../devicetree/bindings/bus/mvebu-mbus.txt         | 253 +++++++++++++++++++++
 drivers/bus/mvebu-mbus.c                           | 121 +++++++++-
 2 files changed, 373 insertions(+), 1 deletion(-)
 create mode 100644 Documentation/devicetree/bindings/bus/mvebu-mbus.txt

Documentation/devicetree/bindings/bus/mvebu-mbus.txt new file +253 -0

new file mode 100644
index 0000000..cce863f
@@ -0,0 +1,253 @@
+
+* Marvell MBus
+
+Required properties:
+
+- compatible:	 Should be set to one of the following:
+		 marvell,armada370-mbus
+		 marvell,armadaxp-mbus
+
+- address-cells: Must be '2'. The first cell for the MBus ID encoding,
+                 the second cell for the address offset within the window.
+
+- size-cells:    Must be '1'.
+
+- ranges:        Must be set up to provide a proper translation for each child.
+	         See the examples below.
+
+- controller:    Contains a single phandle referring to the MBus controller
+                 node. This allows to specify the node that contains the
+		 registers that control the MBus, which is typically contained
+		 within the internal register window (see below).
+
+* Marvell MBus controller
+
+Required properties:
+
+- compatible:	Should be set to "marvell,mbus-controller".
+
+- reg:          Device's register space.
+		Two entries are expected (see the examples below):
+		the first one controls the devices decoding window and
+		the second one controls the SDRAM decoding window.
+
+Example:
+
+	soc {
+		compatible = "marvell,armada370-mbus", "simple-bus";
+		#address-cells = <2>;
+		#size-cells = <1>;
+		controller = <&mbusc>;
+
+		internal-regs {
+			compatible = "simple-bus";
+
+			mbusc: mbus-controller at 20000 {
+				compatible = "marvell,mbus-controller";
+				reg = <0x20000 0x100>, <0x20180 0x20>;
+			};
+
+			/* more children ...*/
+		};
+	};
+
+** MBus address decoding window specification
+
+The MBus children address space is comprised of two cells: the first one for
+the window ID and the second one for the offset within the window.
+In order to allow to describe valid and non-valid window entries, the
+following encoding is used:
+
+  0xSIAA0000 0x00oooooo
+
+Where:
+
+  S = 0x0 for a MBus valid window
+  S = 0xf for a non-valid window (see below)
+
+If S = 0x0, then:
+
+   I = 4-bit window target ID
+  AA = windpw attribute
+
+If S = 0xf, then:
+
+   I = don't care
+   AA = 1 for internal register
+
+Following the above encoding, for each ranges entry for a MBus valid window
+(S = 0x0), an address decoding window is allocated. On the other side,
+entries for translation that do not correspond to valid windows (S = 0xf)
+are skipped.
+
+	soc {
+		compatible = "marvell,armada370-mbus", "simple-bus";
+		#address-cells = <2>;
+		#size-cells = <1>;
+		controller = <&mbusc>;
+
+		ranges = <0xf0010000 0 0 0xd0000000 0x100000
+			  0x01e00000 0 0 0xfff00000 0x100000>;
+
+		bootrom {
+			compatible = "marvell,bootrom";
+			reg = <0x01e00000 0 0x100000>;
+		};
+
+		/* other children */
+		...
+
+		internal-regs {
+			compatible = "simple-bus";
+			ranges = <0 0xf0010000 0 0x100000>;
+
+			mbusc: mbus-controller at 20000 {
+				compatible = "marvell,mbus-controller";
+				reg = <0x20000 0x100>, <0x20180 0x20>;
+			};
+
+			/* more children ...*/
+		};
+	};
+
+In the shown example, the translation entry in the 'ranges' property is what
+makes the MBus driver create a static decoding window for the corresponding
+given child device. Note that the binding does not require child nodes to be
+present. Of course, child nodes are needed to probe the devices.
+
+Since each window is identified by its target ID and attribute ID there's
+a special macro that can be use to simplify the translation entries:
+
+#define MBUS_ID(target,attributes) (((target) << 24) | ((attributes) << 16))
+
+Using this macro, the above example would be:
+
+	soc {
+		compatible = "marvell,armada370-mbus", "simple-bus";
+		#address-cells = <2>;
+		#size-cells = <1>;
+		controller = <&mbusc>;
+
+		ranges = < MBUS_ID(0xf0, 0x01) 0 0 0xd0000000 0x100000
+			   MBUS_ID(0x01, 0xe0) 0 0 0xfff00000 0x100000>;
+
+		bootrom {
+			compatible = "marvell,bootrom";
+			reg = <MBUS_ID(0x01, 0xe0) 0 0x100000>;
+		};
+
+		/* other children */
+		...
+
+		internal-regs {
+			compatible = "simple-bus";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 MBUS_ID(0xf0, 0x01) 0 0x100000>;
+
+			mbusc: mbus-controller at 20000 {
+				compatible = "marvell,mbus-controller";
+				reg = <0x20000 0x100>, <0x20180 0x20>;
+			};
+
+			/* other children */
+			...
+		};
+	};
+
+
+** About the window base address
+
+Remember the MBus controller allows a great deal of flexibility for choosing
+the decoding window base address. When planning the device tree layout it's
+possible to choose any address as the base address, provided of course there's
+a region large enough available, and with the required alignment.
+
+Yet in other words: there's nothing preventing us from setting a base address
+of 0xf0000000, or 0xd0000000 for the NOR device shown above, if such region is
+unused.
+
+** Window allocation policy
+
+The mbus-node ranges property defines a set of mbus windows that are expected
+to be set by the operating system and that are guaranteed to be free of overlaps
+with one another or with the system memory ranges.
+
+Each entry in the property refers to exactly one window. If the operating system
+choses to use a different set of mbus windows, it must ensure that any address
+translations performed from downstream devices are adapted accordingly.
+
+The operating system may insert additional mbus windows that do not conflict
+with the ones listed in the ranges, e.g. for mapping PCIe devices.
+As a special case, the internal register window must be set up by the boot
+loader at the address listed in the ranges property, since access to that region
+is needed to set up the other windows.
+
+** Example
+
+See the example below, where a more complete device tree is shown:
+
+	soc {
+		compatible = "marvell,armadaxp-mbus", "simple-bus";
+		controller = <&mbusc>;
+
+		ranges = <MBUS_ID(0xf0, 0x01) 0 0 0xd0000000 0x100000   /* internal-regs */
+			  MBUS_ID(0x01, 0x1d) 0 0 0xfff00000 0x100000
+			  MBUS_ID(0x01, 0x2f) 0 0 0xf0000000 0x8000000>;
+
+		bootrom {
+			compatible = "marvell,bootrom";
+			reg = <MBUS_ID(0x01, 0x1d) 0 0x100000>;
+		};
+
+		devbus-bootcs {
+			status = "okay";
+			ranges = <0 MBUS_ID(0x01, 0x2f) 0 0x8000000>;
+
+			/* NOR */
+			nor {
+				compatible = "cfi-flash";
+				reg = <0 0x8000000>;
+				bank-width = <2>;
+			};
+		};
+
+		pcie-controller {
+			compatible = "marvell,armada-xp-pcie";
+			status = "okay";
+			device_type = "pci";
+
+			#address-cells = <3>;
+			#size-cells = <2>;
+
+			ranges =
+			       <0x82000000 0 0x40000 MBUS_ID(0xf0, 0x01) 0x40000 0 0x00002000   /* Port 0.0 registers */
+				0x82000000 0 0x42000 MBUS_ID(0xf0, 0x01) 0x42000 0 0x00002000   /* Port 2.0 registers */
+				0x82000000 0 0x44000 MBUS_ID(0xf0, 0x01) 0x44000 0 0x00002000   /* Port 0.1 registers */
+				0x82000000 0 0x48000 MBUS_ID(0xf0, 0x01) 0x48000 0 0x00002000   /* Port 0.2 registers */
+				0x82000000 0 0x4c000 MBUS_ID(0xf0, 0x01) 0x4c000 0 0x00002000   /* Port 0.3 registers */
+				0x82000800 0 0xe0000000 MBUS_ID(0x04, 0xe8) 0xe0000000 0 0x08000000 /* Port 0.0 MEM */
+				0x81000800 0 0          MBUS_ID(0x04, 0xe0) 0xe8000000 0 0x00100000 /* Port 0.0 IO */>;
+
+
+			pcie at 1,0 {
+				/* Port 0, Lane 0 */
+				status = "okay";
+			};
+		};
+
+		internal-regs {
+			compatible = "simple-bus";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 MBUS_ID(0xf0, 0x01) 0 0x100000>;
+
+			mbusc: mbus-controller at 20000 {
+				reg = <0x20000 0x100>, <0x20180 0x20>;
+			};
+
+			interrupt-controller at 20000 {
+			      reg = <0x20a00 0x2d0>, <0x21070 0x58>;
+			};
+		};
+	};

drivers/bus/mvebu-mbus.c +120 -1

132 lines not on this page · raw message

Signature · 1 line

1.8.1.5

Ezequiel Garcia

author

2013-07-15 14:57 UTC #10 lore raw

PATCH RESEND v7 10/22 bus: mvebu-mbus: Add new API for the PCIe memory and IO aperture

We add two optional properties to the MBus DT binding, to encode the PCIe memory and IO aperture. This allows such information to be retrieved by -for instance- the pci driver to allocate the MBus decoding windows.

Correspondingly, and in order to retrieve this information, we add two new APIs.

---
 .../devicetree/bindings/bus/mvebu-mbus.txt         | 14 +++++++
 drivers/bus/mvebu-mbus.c                           | 49 ++++++++++++++++++++++
 include/linux/mbus.h                               |  4 ++
 3 files changed, 67 insertions(+)

Documentation/devicetree/bindings/bus/mvebu-mbus.txt +14 -0

index cce863f..960186f 100644
@@ -20,6 +20,18 @@ Required properties:
 		 registers that control the MBus, which is typically contained
 		 within the internal register window (see below).
 
+Optional properties:
+
+- pcie-mem-aperture:	This optional property contains the aperture for
+			the memory region of the PCIe driver.
+			If it's defined, it must encode the base address and
+			size for the address decoding windows allocated for
+			the PCIe memory region.
+
+- pcie-io-aperture:	Just as explained for the above property, this
+			optional property contains the aperture for the
+			I/O region of the PCIe driver.
+
 * Marvell MBus controller
 
 Required properties:

@@ -38,6 +50,8 @@ Example:
 		#address-cells = <2>;
 		#size-cells = <1>;
 		controller = <&mbusc>;
+		pcie-mem-aperture = <0xe0000000 0x8000000>;
+		pcie-io-aperture  = <0xe8000000 0x100000>;
 
 		internal-regs {
 			compatible = "simple-bus";

drivers/bus/mvebu-mbus.c +49 -0

73 lines not on this page · raw message

include/linux/mbus.h +4 -0

index eadefd6..650bc15 100644
@@ -11,6 +11,8 @@
 #ifndef __LINUX_MBUS_H
 #define __LINUX_MBUS_H
 
+struct resource;
+
 struct mbus_dram_target_info
 {
 	/*

@@ -59,6 +61,8 @@ static inline const struct mbus_dram_target_info *mv_mbus_dram_info(void)
 }
 #endif
 
+void mvebu_mbus_get_pcie_mem_aperture(struct resource *res);
+void mvebu_mbus_get_pcie_io_aperture(struct resource *res);
 int mvebu_mbus_add_window_remap_flags(const char *devname, phys_addr_t base,
 				      size_t size, phys_addr_t remap,
 				      unsigned int flags);

Signature · 1 line

1.8.1.5

Ezequiel Garcia

author

2013-07-15 14:57 UTC #11 lore raw

PATCH RESEND v7 11/22 PCI: mvebu: Adapt to the new device tree layout

From: Thomas Petazzoni <[email protected]>

The new device tree layout encodes the window's target ID and attribute in the PCIe controller node's ranges property. This allows to parse such entries to obtain such information and use the recently introduced MBus API to create the windows, instead of using the current name based scheme.

Acked-by Bjorn Helgaas <[email protected]>

---
 .../devicetree/bindings/pci/mvebu-pci.txt          | 145 ++++++++++++++++-----
 drivers/pci/host/pci-mvebu.c                       | 113 +++++++++++-----
 2 files changed, 193 insertions(+), 65 deletions(-)

Documentation/devicetree/bindings/pci/mvebu-pci.txt +109 ~~-36~~

index f8d4058..9556e2f 100644
@@ -1,6 +1,7 @@
 * Marvell EBU PCIe interfaces
 
 Mandatory properties:
+
 - compatible: one of the following values:
     marvell,armada-370-pcie
     marvell,armada-xp-pcie

@@ -10,11 +11,49 @@ Mandatory properties:
 - #interrupt-cells, set to <1>
 - bus-range: PCI bus numbers covered
 - device_type, set to "pci"
-- ranges: ranges for the PCI memory and I/O regions, as well as the
-  MMIO registers to control the PCIe interfaces.
+- ranges: ranges describing the MMIO registers to control the PCIe
+  interfaces, and ranges describing the MBus windows needed to access
+  the memory and I/O regions of each PCIe interface.
+
+The ranges describing the MMIO registers have the following layout:
+
+    0x82000000 0 r MBUS_ID(0xf0, 0x01) r 0 s
+
+where:
+
+  * r is a 32-bits value that gives the offset of the MMIO
+  registers of this PCIe interface, from the base of the internal
+  registers.
+
+  * s is a 32-bits value that give the size of this MMIO
+  registers area. This range entry translates the '0x82000000 0 r' PCI
+  address into the 'MBUS_ID(0xf0, 0x01) r' CPU address, which is part
+  of the internal register window (as identified by MBUS_ID(0xf0,
+  0x01)).
+
+The ranges describing the MBus windows have the following layout:
+
+    0x8t000000 s 0     MBUS_ID(w, a) 0 1 0
+
+where:
+
+   * t is the type of the MBus window (as defined by the standard PCI DT
+   bindings), 1 for I/O and 2 for memory.
 
-In addition, the Device Tree node must have sub-nodes describing each
+   * s is the PCI slot that corresponds to this PCIe interface
+
+   * w is the 'target ID' value for the MBus window
+
+   * a the 'attribute' value for the MBus window.
+
+Since the location and size of the different MBus windows is not fixed in
+hardware, and only determined in runtime, those ranges cover the full first
+4 GB of the physical address space, and do not translate into a valid CPU
+address.
+
+In addition, the device tree node must have sub-nodes describing each
 PCIe interface, having the following mandatory properties:
+
 - reg: used only for interrupt mapping, so only the first four bytes
   are used to refer to the correct bus number and device number.
 - assigned-addresses: reference to the MMIO registers used to control

@@ -26,7 +65,8 @@ PCIe interface, having the following mandatory properties:
 - #address-cells, set to <3>
 - #size-cells, set to <2>
 - #interrupt-cells, set to <1>
-- ranges, empty property.
+- ranges, translating the MBus windows ranges of the parent node into
+  standard PCI addresses.
 - interrupt-map-mask and interrupt-map, standard PCI properties to
   define the mapping of the PCIe interface to interrupt numbers.

@@ -47,27 +87,50 @@ pcie-controller {
 
 	bus-range = <0x00 0xff>;
 
-	ranges = <0x82000000 0 0xd0040000 0xd0040000 0 0x00002000   /* Port 0.0 registers */
-		  0x82000000 0 0xd0042000 0xd0042000 0 0x00002000   /* Port 2.0 registers */
-		  0x82000000 0 0xd0044000 0xd0044000 0 0x00002000   /* Port 0.1 registers */
-		  0x82000000 0 0xd0048000 0xd0048000 0 0x00002000   /* Port 0.2 registers */
-		  0x82000000 0 0xd004c000 0xd004c000 0 0x00002000   /* Port 0.3 registers */
-		  0x82000000 0 0xd0080000 0xd0080000 0 0x00002000   /* Port 1.0 registers */
-		  0x82000000 0 0xd0082000 0xd0082000 0 0x00002000   /* Port 3.0 registers */
-		  0x82000000 0 0xd0084000 0xd0084000 0 0x00002000   /* Port 1.1 registers */
-		  0x82000000 0 0xd0088000 0xd0088000 0 0x00002000   /* Port 1.2 registers */
-		  0x82000000 0 0xd008c000 0xd008c000 0 0x00002000   /* Port 1.3 registers */
-		  0x82000000 0 0xe0000000 0xe0000000 0 0x08000000   /* non-prefetchable memory */
-		  0x81000000 0 0	  0xe8000000 0 0x00100000>; /* downstream I/O */
+	ranges =
+	       <0x82000000 0 0x40000 MBUS_ID(0xf0, 0x01) 0x40000 0 0x00002000	/* Port 0.0 registers */
+		0x82000000 0 0x42000 MBUS_ID(0xf0, 0x01) 0x42000 0 0x00002000	/* Port 2.0 registers */
+		0x82000000 0 0x44000 MBUS_ID(0xf0, 0x01) 0x44000 0 0x00002000	/* Port 0.1 registers */
+		0x82000000 0 0x48000 MBUS_ID(0xf0, 0x01) 0x48000 0 0x00002000	/* Port 0.2 registers */
+		0x82000000 0 0x4c000 MBUS_ID(0xf0, 0x01) 0x4c000 0 0x00002000	/* Port 0.3 registers */
+		0x82000000 0 0x80000 MBUS_ID(0xf0, 0x01) 0x80000 0 0x00002000	/* Port 1.0 registers */
+		0x82000000 0 0x82000 MBUS_ID(0xf0, 0x01) 0x82000 0 0x00002000	/* Port 3.0 registers */
+		0x82000000 0 0x84000 MBUS_ID(0xf0, 0x01) 0x84000 0 0x00002000	/* Port 1.1 registers */
+		0x82000000 0 0x88000 MBUS_ID(0xf0, 0x01) 0x88000 0 0x00002000	/* Port 1.2 registers */
+		0x82000000 0 0x8c000 MBUS_ID(0xf0, 0x01) 0x8c000 0 0x00002000	/* Port 1.3 registers */
+		0x82000000 0x1 0     MBUS_ID(0x04, 0xe8) 0 1 0 /* Port 0.0 MEM */
+		0x81000000 0x1 0     MBUS_ID(0x04, 0xe0) 0 1 0 /* Port 0.0 IO  */
+		0x82000000 0x2 0     MBUS_ID(0x04, 0xd8) 0 1 0 /* Port 0.1 MEM */
+		0x81000000 0x2 0     MBUS_ID(0x04, 0xd0) 0 1 0 /* Port 0.1 IO  */
+		0x82000000 0x3 0     MBUS_ID(0x04, 0xb8) 0 1 0 /* Port 0.2 MEM */
+		0x81000000 0x3 0     MBUS_ID(0x04, 0xb0) 0 1 0 /* Port 0.2 IO  */
+		0x82000000 0x4 0     MBUS_ID(0x04, 0x78) 0 1 0 /* Port 0.3 MEM */
+		0x81000000 0x4 0     MBUS_ID(0x04, 0x70) 0 1 0 /* Port 0.3 IO  */
+
+		0x82000000 0x5 0     MBUS_ID(0x08, 0xe8) 0 1 0 /* Port 1.0 MEM */
+		0x81000000 0x5 0     MBUS_ID(0x08, 0xe0) 0 1 0 /* Port 1.0 IO  */
+		0x82000000 0x6 0     MBUS_ID(0x08, 0xd8) 0 1 0 /* Port 1.1 MEM */
+		0x81000000 0x6 0     MBUS_ID(0x08, 0xd0) 0 1 0 /* Port 1.1 IO  */
+		0x82000000 0x7 0     MBUS_ID(0x08, 0xb8) 0 1 0 /* Port 1.2 MEM */
+		0x81000000 0x7 0     MBUS_ID(0x08, 0xb0) 0 1 0 /* Port 1.2 IO  */
+		0x82000000 0x8 0     MBUS_ID(0x08, 0x78) 0 1 0 /* Port 1.3 MEM */
+		0x81000000 0x8 0     MBUS_ID(0x08, 0x70) 0 1 0 /* Port 1.3 IO  */
+
+		0x82000000 0x9 0     MBUS_ID(0x04, 0xf8) 0 1 0 /* Port 2.0 MEM */
+		0x81000000 0x9 0     MBUS_ID(0x04, 0xf0) 0 1 0 /* Port 2.0 IO  */
+
+		0x82000000 0xa 0     MBUS_ID(0x08, 0xf8) 0 1 0 /* Port 3.0 MEM */
+		0x81000000 0xa 0     MBUS_ID(0x08, 0xf0) 0 1 0 /* Port 3.0 IO  */>;
 
 	pcie at 1,0 {
 		device_type = "pci";
-		assigned-addresses = <0x82000800 0 0xd0040000 0 0x2000>;
+		assigned-addresses = <0x82000800 0 0x40000 0 0x2000>;
 		reg = <0x0800 0 0 0 0>;
 		#address-cells = <3>;
 		#size-cells = <2>;
 		#interrupt-cells = <1>;
-		ranges;
+		ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0
+			  0x81000000 0 0 0x81000000 0x1 0 1 0>;
 		interrupt-map-mask = <0 0 0 0>;
 		interrupt-map = <0 0 0 0 &mpic 58>;
 		marvell,pcie-port = <0>;

@@ -78,12 +141,13 @@ pcie-controller {
 
 	pcie at 2,0 {
 		device_type = "pci";
-		assigned-addresses = <0x82001000 0 0xd0044000 0 0x2000>;
+		assigned-addresses = <0x82001000 0 0x44000 0 0x2000>;
 		reg = <0x1000 0 0 0 0>;
 		#address-cells = <3>;
 		#size-cells = <2>;
 		#interrupt-cells = <1>;
-		ranges;
+		ranges = <0x82000000 0 0 0x82000000 0x2 0 1 0
+			  0x81000000 0 0 0x81000000 0x2 0 1 0>;
 		interrupt-map-mask = <0 0 0 0>;
 		interrupt-map = <0 0 0 0 &mpic 59>;
 		marvell,pcie-port = <0>;

@@ -94,12 +158,13 @@ pcie-controller {
 
 	pcie at 3,0 {
 		device_type = "pci";
-		assigned-addresses = <0x82001800 0 0xd0048000 0 0x2000>;
+		assigned-addresses = <0x82001800 0 0x48000 0 0x2000>;
 		reg = <0x1800 0 0 0 0>;
 		#address-cells = <3>;
 		#size-cells = <2>;
 		#interrupt-cells = <1>;
-		ranges;
+		ranges = <0x82000000 0 0 0x82000000 0x3 0 1 0
+			  0x81000000 0 0 0x81000000 0x3 0 1 0>;
 		interrupt-map-mask = <0 0 0 0>;
 		interrupt-map = <0 0 0 0 &mpic 60>;
 		marvell,pcie-port = <0>;

@@ -110,12 +175,13 @@ pcie-controller {
 
 	pcie at 4,0 {
 		device_type = "pci";
-		assigned-addresses = <0x82002000 0 0xd004c000 0 0x2000>;
+		assigned-addresses = <0x82002000 0 0x4c000 0 0x2000>;
 		reg = <0x2000 0 0 0 0>;
 		#address-cells = <3>;
 		#size-cells = <2>;
 		#interrupt-cells = <1>;
-		ranges;
+		ranges = <0x82000000 0 0 0x82000000 0x4 0 1 0
+			  0x81000000 0 0 0x81000000 0x4 0 1 0>;
 		interrupt-map-mask = <0 0 0 0>;
 		interrupt-map = <0 0 0 0 &mpic 61>;
 		marvell,pcie-port = <0>;

@@ -126,12 +192,13 @@ pcie-controller {
 
 	pcie at 5,0 {
 		device_type = "pci";
-		assigned-addresses = <0x82002800 0 0xd0080000 0 0x2000>;
+		assigned-addresses = <0x82002800 0 0x80000 0 0x2000>;
 		reg = <0x2800 0 0 0 0>;
 		#address-cells = <3>;
 		#size-cells = <2>;
 		#interrupt-cells = <1>;
-		ranges;
+		ranges = <0x82000000 0 0 0x82000000 0x5 0 1 0
+			  0x81000000 0 0 0x81000000 0x5 0 1 0>;
 		interrupt-map-mask = <0 0 0 0>;
 		interrupt-map = <0 0 0 0 &mpic 62>;
 		marvell,pcie-port = <1>;

@@ -142,12 +209,13 @@ pcie-controller {
 
 	pcie at 6,0 {
 		device_type = "pci";
-		assigned-addresses = <0x82003000 0 0xd0084000 0 0x2000>;
+		assigned-addresses = <0x82003000 0 0x84000 0 0x2000>;
 		reg = <0x3000 0 0 0 0>;
 		#address-cells = <3>;
 		#size-cells = <2>;
 		#interrupt-cells = <1>;
-		ranges;
+		ranges = <0x82000000 0 0 0x82000000 0x6 0 1 0
+			  0x81000000 0 0 0x81000000 0x6 0 1 0>;
 		interrupt-map-mask = <0 0 0 0>;
 		interrupt-map = <0 0 0 0 &mpic 63>;
 		marvell,pcie-port = <1>;

@@ -158,12 +226,13 @@ pcie-controller {
 
 	pcie at 7,0 {
 		device_type = "pci";
-		assigned-addresses = <0x82003800 0 0xd0088000 0 0x2000>;
+		assigned-addresses = <0x82003800 0 0x88000 0 0x2000>;
 		reg = <0x3800 0 0 0 0>;
 		#address-cells = <3>;
 		#size-cells = <2>;
 		#interrupt-cells = <1>;
-		ranges;
+		ranges = <0x82000000 0 0 0x82000000 0x7 0 1 0
+			  0x81000000 0 0 0x81000000 0x7 0 1 0>;
 		interrupt-map-mask = <0 0 0 0>;
 		interrupt-map = <0 0 0 0 &mpic 64>;
 		marvell,pcie-port = <1>;

@@ -174,12 +243,13 @@ pcie-controller {
 
 	pcie at 8,0 {
 		device_type = "pci";
-		assigned-addresses = <0x82004000 0 0xd008c000 0 0x2000>;
+		assigned-addresses = <0x82004000 0 0x8c000 0 0x2000>;
 		reg = <0x4000 0 0 0 0>;
 		#address-cells = <3>;
 		#size-cells = <2>;
 		#interrupt-cells = <1>;
-		ranges;
+		ranges = <0x82000000 0 0 0x82000000 0x8 0 1 0
+			  0x81000000 0 0 0x81000000 0x8 0 1 0>;
 		interrupt-map-mask = <0 0 0 0>;
 		interrupt-map = <0 0 0 0 &mpic 65>;
 		marvell,pcie-port = <1>;

@@ -187,14 +257,16 @@ pcie-controller {
 		clocks = <&gateclk 12>;
 		status = "disabled";
 	};
+
 	pcie at 9,0 {
 		device_type = "pci";
-		assigned-addresses = <0x82004800 0 0xd0042000 0 0x2000>;
+		assigned-addresses = <0x82004800 0 0x42000 0 0x2000>;
 		reg = <0x4800 0 0 0 0>;
 		#address-cells = <3>;
 		#size-cells = <2>;
 		#interrupt-cells = <1>;
-		ranges;
+		ranges = <0x82000000 0 0 0x82000000 0x9 0 1 0
+			  0x81000000 0 0 0x81000000 0x9 0 1 0>;
 		interrupt-map-mask = <0 0 0 0>;
 		interrupt-map = <0 0 0 0 &mpic 99>;
 		marvell,pcie-port = <2>;

@@ -205,12 +277,13 @@ pcie-controller {
 
 	pcie at 10,0 {
 		device_type = "pci";
-		assigned-addresses = <0x82005000 0 0xd0082000 0 0x2000>;
+		assigned-addresses = <0x82005000 0 0x82000 0 0x2000>;
 		reg = <0x5000 0 0 0 0>;
 		#address-cells = <3>;
 		#size-cells = <2>;
 		#interrupt-cells = <1>;
-		ranges;
+		ranges = <0x82000000 0 0 0x82000000 0xa 0 1 0
+			  0x81000000 0 0 0x81000000 0xa 0 1 0>;
 		interrupt-map-mask = <0 0 0 0>;
 		interrupt-map = <0 0 0 0 &mpic 103>;
 		marvell,pcie-port = <3>;

drivers/pci/host/pci-mvebu.c +84 ~~-29~~

157 lines not on this page · raw message

Signature · 1 line

1.8.1.5

Ezequiel Garcia

author

2013-07-15 14:57 UTC #12 lore raw

PATCH RESEND v7 12/22 bus: mvebu-mbus: Remove the no longer used name-based API

From: Thomas Petazzoni <[email protected]>

Now that every user of the deprecated name-based API has been converted to using the ID-based API, let's remove the former one.

---
 drivers/bus/mvebu-mbus.c | 38 --------------------------------------
 include/linux/mbus.h     |  5 -----
 2 files changed, 43 deletions(-)

drivers/bus/mvebu-mbus.c +0 ~~-38~~

index 5f0bfa3..9aee344 100644
@@ -766,44 +766,6 @@ int mvebu_mbus_add_window_remap_by_id(unsigned int target,
 	return mvebu_mbus_alloc_window(s, base, size, remap, target, attribute);
 }
 
-int mvebu_mbus_add_window_remap_flags(const char *devname, phys_addr_t base,
-				      size_t size, phys_addr_t remap,
-				      unsigned int flags)
-{
-	struct mvebu_mbus_state *s = &mbus_state;
-	u8 target, attr;
-	int i;
-
-	if (!s->soc->map)
-		return -ENODEV;
-
-	for (i = 0; s->soc->map[i].name; i++)
-		if (!strcmp(s->soc->map[i].name, devname))
-			break;
-
-	if (!s->soc->map[i].name) {
-		pr_err("unknown device '%s'\n", devname);
-		return -ENODEV;
-	}
-
-	target = s->soc->map[i].target;
-	attr   = s->soc->map[i].attr;
-
-	if (flags == MVEBU_MBUS_PCI_MEM)
-		attr |= 0x8;
-	else if (flags == MVEBU_MBUS_PCI_WA)
-		attr |= 0x28;
-
-	return mvebu_mbus_add_window_remap_by_id(target, attr, base,
-						 size, remap);
-}
-
-int mvebu_mbus_add_window(const char *devname, phys_addr_t base, size_t size)
-{
-	return mvebu_mbus_add_window_remap_flags(devname, base, size,
-						 MVEBU_MBUS_NO_REMAP, 0);
-}
-
 int mvebu_mbus_add_window_by_id(unsigned int target, unsigned int attribute,
 				phys_addr_t base, size_t size)
 {

include/linux/mbus.h +0 -5

index 650bc15..345b8c5 100644
@@ -63,15 +63,10 @@ static inline const struct mbus_dram_target_info *mv_mbus_dram_info(void)
 
 void mvebu_mbus_get_pcie_mem_aperture(struct resource *res);
 void mvebu_mbus_get_pcie_io_aperture(struct resource *res);
-int mvebu_mbus_add_window_remap_flags(const char *devname, phys_addr_t base,
-				      size_t size, phys_addr_t remap,
-				      unsigned int flags);
 int mvebu_mbus_add_window_remap_by_id(unsigned int target,
 				      unsigned int attribute,
 				      phys_addr_t base, size_t size,
 				      phys_addr_t remap);
-int mvebu_mbus_add_window(const char *devname, phys_addr_t base,
-			  size_t size);
 int mvebu_mbus_add_window_by_id(unsigned int target, unsigned int attribute,
 				phys_addr_t base, size_t size);
 int mvebu_mbus_del_window(phys_addr_t base, size_t size);

Signature · 1 line

1.8.1.5

Ezequiel Garcia

author

2013-07-15 14:57 UTC #13 lore raw

PATCH RESEND v7 13/22 bus: mvebu-mbus: Remove name -> target, attribute mapping tables

From: Thomas Petazzoni <[email protected]>

This tables were used together with the name-based MBus window creation API. Since that's has been removed, we can also remove the tables.

---
 drivers/bus/mvebu-mbus.c | 150 +++--------------------------------------------
 1 file changed, 7 insertions(+), 143 deletions(-)

drivers/bus/mvebu-mbus.c +7 ~~-143~~

index 9aee344..e13d475 100644
@@ -97,33 +97,6 @@
 
 #define DOVE_DDR_BASE_CS_OFF(n) ((n) << 4)
 
-struct mvebu_mbus_mapping {
-	const char *name;
-	u8 target;
-	u8 attr;
-	u8 attrmask;
-};
-
-/*
- * Masks used for the 'attrmask' field of mvebu_mbus_mapping. They
- * allow to get the real attribute value, discarding the special bits
- * used to select a PCI MEM region or a PCI WA region. This allows the
- * debugfs code to reverse-match the name of a device from its
- * target/attr values.
- *
- * For all devices except PCI, all bits of 'attr' must be
- * considered. For most SoCs, only bit 3 should be ignored (it allows
- * to select between PCI MEM and PCI I/O). On Orion5x however, there
- * is the special bit 5 to select a PCI WA region.
- */
-#define MAPDEF_NOMASK       0xff
-#define MAPDEF_PCIMASK      0xf7
-#define MAPDEF_ORIONPCIMASK 0xd7
-
-/* Macro used to define one mvebu_mbus_mapping entry */
-#define MAPDEF(__n, __t, __a, __m) \
-	{ .name = __n, .target = __t, .attr = __a, .attrmask = __m }
-
 struct mvebu_mbus_state;
 
 struct mvebu_mbus_soc_data {

@@ -133,7 +106,6 @@ struct mvebu_mbus_soc_data {
 	void (*setup_cpu_target)(struct mvebu_mbus_state *s);
 	int (*show_cpu_target)(struct mvebu_mbus_state *s,
 			       struct seq_file *seq, void *v);
-	const struct mvebu_mbus_mapping *map;
 };
 
 struct mvebu_mbus_state {

@@ -430,8 +402,7 @@ static int mvebu_devs_debug_show(struct seq_file *seq, void *v)
 		u64 wbase, wremap;
 		u32 wsize;
 		u8 wtarget, wattr;
-		int enabled, i;
-		const char *name;
+		int enabled;
 
 		mvebu_mbus_read_window(mbus, win,
 				       &enabled, &wbase, &wsize,

@@ -442,18 +413,9 @@ static int mvebu_devs_debug_show(struct seq_file *seq, void *v)
 			continue;
 		}
 
-
-		for (i = 0; mbus->soc->map[i].name; i++)
-			if (mbus->soc->map[i].target == wtarget &&
-			    mbus->soc->map[i].attr ==
-			    (wattr & mbus->soc->map[i].attrmask))
-				break;
-
-		name = mbus->soc->map[i].name ?: "unknown";
-
-		seq_printf(seq, "[%02d] %016llx - %016llx : %s",
+		seq_printf(seq, "[%02d] %016llx - %016llx : %04x:%04x",
 			   win, (unsigned long long)wbase,
-			   (unsigned long long)(wbase + wsize), name);
+			   (unsigned long long)(wbase + wsize), wtarget, wattr);
 
 		if (win < mbus->soc->num_remappable_wins) {
 			seq_printf(seq, " (remap %016llx)\n",

@@ -578,45 +540,12 @@ mvebu_mbus_dove_setup_cpu_target(struct mvebu_mbus_state *mbus)
 	mvebu_mbus_dram_info.num_cs = cs;
 }
 
-static const struct mvebu_mbus_mapping armada_370_map[] = {
-	MAPDEF("bootrom",     1, 0xe0, MAPDEF_NOMASK),
-	MAPDEF("devbus-boot", 1, 0x2f, MAPDEF_NOMASK),
-	MAPDEF("devbus-cs0",  1, 0x3e, MAPDEF_NOMASK),
-	MAPDEF("devbus-cs1",  1, 0x3d, MAPDEF_NOMASK),
-	MAPDEF("devbus-cs2",  1, 0x3b, MAPDEF_NOMASK),
-	MAPDEF("devbus-cs3",  1, 0x37, MAPDEF_NOMASK),
-	MAPDEF("pcie0.0",     4, 0xe0, MAPDEF_PCIMASK),
-	MAPDEF("pcie1.0",     8, 0xe0, MAPDEF_PCIMASK),
-	{},
-};
-
 static const struct mvebu_mbus_soc_data armada_370_mbus_data = {
 	.num_wins            = 20,
 	.num_remappable_wins = 8,
 	.win_cfg_offset      = armada_370_xp_mbus_win_offset,
 	.setup_cpu_target    = mvebu_mbus_default_setup_cpu_target,
 	.show_cpu_target     = mvebu_sdram_debug_show_orion,
-	.map                 = armada_370_map,
-};
-
-static const struct mvebu_mbus_mapping armada_xp_map[] = {
-	MAPDEF("bootrom",     1, 0x1d, MAPDEF_NOMASK),
-	MAPDEF("devbus-boot", 1, 0x2f, MAPDEF_NOMASK),
-	MAPDEF("devbus-cs0",  1, 0x3e, MAPDEF_NOMASK),
-	MAPDEF("devbus-cs1",  1, 0x3d, MAPDEF_NOMASK),
-	MAPDEF("devbus-cs2",  1, 0x3b, MAPDEF_NOMASK),
-	MAPDEF("devbus-cs3",  1, 0x37, MAPDEF_NOMASK),
-	MAPDEF("pcie0.0",     4, 0xe0, MAPDEF_PCIMASK),
-	MAPDEF("pcie0.1",     4, 0xd0, MAPDEF_PCIMASK),
-	MAPDEF("pcie0.2",     4, 0xb0, MAPDEF_PCIMASK),
-	MAPDEF("pcie0.3",     4, 0x70, MAPDEF_PCIMASK),
-	MAPDEF("pcie1.0",     8, 0xe0, MAPDEF_PCIMASK),
-	MAPDEF("pcie1.1",     8, 0xd0, MAPDEF_PCIMASK),
-	MAPDEF("pcie1.2",     8, 0xb0, MAPDEF_PCIMASK),
-	MAPDEF("pcie1.3",     8, 0x70, MAPDEF_PCIMASK),
-	MAPDEF("pcie2.0",     4, 0xf0, MAPDEF_PCIMASK),
-	MAPDEF("pcie3.0",     8, 0xf0, MAPDEF_PCIMASK),
-	{},
 };
 
 static const struct mvebu_mbus_soc_data armada_xp_mbus_data = {

@@ -625,15 +554,6 @@ static const struct mvebu_mbus_soc_data armada_xp_mbus_data = {
 	.win_cfg_offset      = armada_370_xp_mbus_win_offset,
 	.setup_cpu_target    = mvebu_mbus_default_setup_cpu_target,
 	.show_cpu_target     = mvebu_sdram_debug_show_orion,
-	.map                 = armada_xp_map,
-};
-
-static const struct mvebu_mbus_mapping kirkwood_map[] = {
-	MAPDEF("pcie0.0", 4, 0xe0, MAPDEF_PCIMASK),
-	MAPDEF("pcie1.0", 4, 0xd0, MAPDEF_PCIMASK),
-	MAPDEF("sram",    3, 0x01, MAPDEF_NOMASK),
-	MAPDEF("nand",    1, 0x2f, MAPDEF_NOMASK),
-	{},
 };
 
 static const struct mvebu_mbus_soc_data kirkwood_mbus_data = {

@@ -642,16 +562,6 @@ static const struct mvebu_mbus_soc_data kirkwood_mbus_data = {
 	.win_cfg_offset      = orion_mbus_win_offset,
 	.setup_cpu_target    = mvebu_mbus_default_setup_cpu_target,
 	.show_cpu_target     = mvebu_sdram_debug_show_orion,
-	.map                 = kirkwood_map,
-};
-
-static const struct mvebu_mbus_mapping dove_map[] = {
-	MAPDEF("pcie0.0",    0x4, 0xe0, MAPDEF_PCIMASK),
-	MAPDEF("pcie1.0",    0x8, 0xe0, MAPDEF_PCIMASK),
-	MAPDEF("cesa",       0x3, 0x01, MAPDEF_NOMASK),
-	MAPDEF("bootrom",    0x1, 0xfd, MAPDEF_NOMASK),
-	MAPDEF("scratchpad", 0xd, 0x0, MAPDEF_NOMASK),
-	{},
 };
 
 static const struct mvebu_mbus_soc_data dove_mbus_data = {

@@ -660,18 +570,6 @@ static const struct mvebu_mbus_soc_data dove_mbus_data = {
 	.win_cfg_offset      = orion_mbus_win_offset,
 	.setup_cpu_target    = mvebu_mbus_dove_setup_cpu_target,
 	.show_cpu_target     = mvebu_sdram_debug_show_dove,
-	.map                 = dove_map,
-};
-
-static const struct mvebu_mbus_mapping orion5x_map[] = {
-	MAPDEF("pcie0.0",     4, 0x51, MAPDEF_ORIONPCIMASK),
-	MAPDEF("pci0.0",      3, 0x51, MAPDEF_ORIONPCIMASK),
-	MAPDEF("devbus-boot", 1, 0x0f, MAPDEF_NOMASK),
-	MAPDEF("devbus-cs0",  1, 0x1e, MAPDEF_NOMASK),
-	MAPDEF("devbus-cs1",  1, 0x1d, MAPDEF_NOMASK),
-	MAPDEF("devbus-cs2",  1, 0x1b, MAPDEF_NOMASK),
-	MAPDEF("sram",        0, 0x00, MAPDEF_NOMASK),
-	{},
 };
 
 /*

@@ -684,7 +582,6 @@ static const struct mvebu_mbus_soc_data orion5x_4win_mbus_data = {
 	.win_cfg_offset      = orion_mbus_win_offset,
 	.setup_cpu_target    = mvebu_mbus_default_setup_cpu_target,
 	.show_cpu_target     = mvebu_sdram_debug_show_orion,
-	.map                 = orion5x_map,
 };
 
 static const struct mvebu_mbus_soc_data orion5x_2win_mbus_data = {

@@ -693,21 +590,6 @@ static const struct mvebu_mbus_soc_data orion5x_2win_mbus_data = {
 	.win_cfg_offset      = orion_mbus_win_offset,
 	.setup_cpu_target    = mvebu_mbus_default_setup_cpu_target,
 	.show_cpu_target     = mvebu_sdram_debug_show_orion,
-	.map                 = orion5x_map,
-};
-
-static const struct mvebu_mbus_mapping mv78xx0_map[] = {
-	MAPDEF("pcie0.0", 4, 0xe0, MAPDEF_PCIMASK),
-	MAPDEF("pcie0.1", 4, 0xd0, MAPDEF_PCIMASK),
-	MAPDEF("pcie0.2", 4, 0xb0, MAPDEF_PCIMASK),
-	MAPDEF("pcie0.3", 4, 0x70, MAPDEF_PCIMASK),
-	MAPDEF("pcie1.0", 8, 0xe0, MAPDEF_PCIMASK),
-	MAPDEF("pcie1.1", 8, 0xd0, MAPDEF_PCIMASK),
-	MAPDEF("pcie1.2", 8, 0xb0, MAPDEF_PCIMASK),
-	MAPDEF("pcie1.3", 8, 0x70, MAPDEF_PCIMASK),
-	MAPDEF("pcie2.0", 4, 0xf0, MAPDEF_PCIMASK),
-	MAPDEF("pcie3.0", 8, 0xf0, MAPDEF_PCIMASK),
-	{},
 };
 
 static const struct mvebu_mbus_soc_data mv78xx0_mbus_data = {

@@ -716,7 +598,6 @@ static const struct mvebu_mbus_soc_data mv78xx0_mbus_data = {
 	.win_cfg_offset      = mv78xx0_mbus_win_offset,
 	.setup_cpu_target    = mvebu_mbus_default_setup_cpu_target,
 	.show_cpu_target     = mvebu_sdram_debug_show_orion,
-	.map                 = mv78xx0_map,
 };
 
 /*

@@ -895,33 +776,16 @@ static int __init mbus_dt_setup_win(struct mvebu_mbus_state *mbus,
 				    u32 base, u32 size,
 				    u8 target, u8 attr)
 {
-	const struct mvebu_mbus_mapping *map = mbus->soc->map;
-	const char *name;
-	int i;
-
-	/* Search for a suitable window in the existing mappings */
-	for (i = 0; map[i].name; i++)
-		if (map[i].target == target &&
-		    map[i].attr == (attr & map[i].attrmask))
-			break;
-
-	name = map[i].name;
-	if (!name) {
-		pr_err("window 0x%x:0x%x is unknown, skipping\n",
-		       target, attr);
-		return -EINVAL;
-	}
-
 	if (!mvebu_mbus_window_conflicts(mbus, base, size, target, attr)) {
-		pr_err("cannot add window '%s', conflicts with another window\n",
-		       name);
+		pr_err("cannot add window '%04x:%04x', conflicts with another window\n",
+		       target, attr);
 		return -EBUSY;
 	}
 
 	if (mvebu_mbus_alloc_window(mbus, base, size, MVEBU_MBUS_NO_REMAP,
 				    target, attr)) {
-		pr_err("cannot add window '%s', too many windows\n",
-		       name);
+		pr_err("cannot add window '%04x:%04x', too many windows\n",
+		       target, attr);
 		return -ENOMEM;
 	}
 	return 0;

Signature · 1 line

1.8.1.5

Ezequiel Garcia

author

2013-07-15 14:57 UTC #14 lore raw

PATCH RESEND v7 14/22 bus: mvebu-mbus: Update main description

From: Thomas Petazzoni <[email protected]>

After replacing the MBus name-based by the new ID-based API let's fix the general description of the driver at the beginning of the file.

---
 drivers/bus/mvebu-mbus.c | 10 +++-------
 1 file changed, 3 insertions(+), 7 deletions(-)

drivers/bus/mvebu-mbus.c +3 -7

index e13d475..f6e9192 100644
@@ -35,13 +35,9 @@
  *
  * - Provides an API for platform code or device drivers to
  *   dynamically add or remove address decoding windows for the CPU ->
- *   device accesses. This API is mvebu_mbus_add_window(),
- *   mvebu_mbus_add_window_remap_flags() and
- *   mvebu_mbus_del_window(). Since the (target, attribute) values
- *   differ from one SoC family to another, the API uses a 'const char
- *   *' string to identify devices, and this driver is responsible for
- *   knowing the mapping between the name of a device and its
- *   corresponding (target, attribute) in the current SoC family.
+ *   device accesses. This API is mvebu_mbus_add_window_by_id(),
+ *   mvebu_mbus_add_window_remap_by_id() and
+ *   mvebu_mbus_del_window().
  *
  * - Provides a debugfs interface in /sys/kernel/debug/mvebu-mbus/ to
  *   see the list of CPU -> SDRAM windows and their configuration

Signature · 1 line

1.8.1.5

Ezequiel Garcia

author

2013-07-15 14:57 UTC #15 lore raw

PATCH RESEND v7 15/22 bus: mvebu-mbus: Factorize Armada 370/XP data structures

From: Thomas Petazzoni <[email protected]>

These structures were only different in the mapping tables. Now that those tables have been removed, it doesn't make any sense to keep different structures.

---
 drivers/bus/mvebu-mbus.c | 14 +++-----------
 1 file changed, 3 insertions(+), 11 deletions(-)

drivers/bus/mvebu-mbus.c +3 ~~-11~~

index f6e9192..d0a61ce 100644
@@ -536,15 +536,7 @@ mvebu_mbus_dove_setup_cpu_target(struct mvebu_mbus_state *mbus)
 	mvebu_mbus_dram_info.num_cs = cs;
 }
 
-static const struct mvebu_mbus_soc_data armada_370_mbus_data = {
-	.num_wins            = 20,
-	.num_remappable_wins = 8,
-	.win_cfg_offset      = armada_370_xp_mbus_win_offset,
-	.setup_cpu_target    = mvebu_mbus_default_setup_cpu_target,
-	.show_cpu_target     = mvebu_sdram_debug_show_orion,
-};
-
-static const struct mvebu_mbus_soc_data armada_xp_mbus_data = {
+static const struct mvebu_mbus_soc_data armada_370_xp_mbus_data = {
 	.num_wins            = 20,
 	.num_remappable_wins = 8,
 	.win_cfg_offset      = armada_370_xp_mbus_win_offset,

@@ -604,9 +596,9 @@ static const struct mvebu_mbus_soc_data mv78xx0_mbus_data = {
  */
 static const struct of_device_id of_mvebu_mbus_ids[] = {
 	{ .compatible = "marvell,armada370-mbus",
-	  .data = &armada_370_mbus_data, },
+	  .data = &armada_370_xp_mbus_data, },
 	{ .compatible = "marvell,armadaxp-mbus",
-	  .data = &armada_xp_mbus_data, },
+	  .data = &armada_370_xp_mbus_data, },
 	{ .compatible = "marvell,kirkwood-mbus",
 	  .data = &kirkwood_mbus_data, },
 	{ .compatible = "marvell,dove-mbus",

Signature · 1 line

1.8.1.5

Ezequiel Garcia

author

2013-07-15 14:57 UTC #16 lore raw

PATCH RESEND v7 16/22 ARM: mvebu: Remove the harcoded BootROM window allocation

The address decoding window to access the BootROM should not be allocated programatically, but instead declared in the device tree.

---
 arch/arm/mach-mvebu/platsmp.c | 25 ++++++++++++++++++++++++-
 1 file changed, 24 insertions(+), 1 deletion(-)

arch/arm/mach-mvebu/platsmp.c +24 -1

index 93f2f3a..a952f8d 100644
@@ -21,6 +21,7 @@
 #include <linux/smp.h>
 #include <linux/clk.h>
 #include <linux/of.h>
+#include <linux/of_address.h>
 #include <linux/mbus.h>
 #include <asm/cacheflush.h>
 #include <asm/smp_plat.h>

@@ -29,6 +30,9 @@
 #include "pmsu.h"
 #include "coherency.h"
 
+#define AXP_BOOTROM_BASE 0xfff00000
+#define AXP_BOOTROM_SIZE 0x100000
+
 void __init set_secondary_cpus_clock(void)
 {
 	int thiscpu;

@@ -115,10 +119,29 @@ static void __init armada_xp_smp_init_cpus(void)
 
 void __init armada_xp_smp_prepare_cpus(unsigned int max_cpus)
 {
+	struct device_node *node;
+	struct resource res;
+	int err;
+
 	set_secondary_cpus_clock();
 	flush_cache_all();
 	set_cpu_coherent(cpu_logical_map(smp_processor_id()), 0);
-	mvebu_mbus_add_window("bootrom", 0xfff00000, SZ_1M);
+
+	/*
+	 * In order to boot the secondary CPUs we need to ensure
+	 * the bootROM is mapped at the correct address.
+	 */
+	node = of_find_compatible_node(NULL, NULL, "marvell,bootrom");
+	if (!node)
+		panic("Cannot find 'marvell,bootrom' compatible node");
+
+	err = of_address_to_resource(node, 0, &res);
+	if (err < 0)
+		panic("Cannot get 'bootrom' node address");
+
+	if (res.start != AXP_BOOTROM_BASE||
+	    resource_size(&res) != AXP_BOOTROM_SIZE)
+		panic("The address for the BootROM is incorrect");
 }
 
 struct smp_operations armada_xp_smp_ops __initdata = {

Signature · 1 line

1.8.1.5

Ezequiel Garcia

author

2013-07-15 14:57 UTC #17 lore raw

PATCH RESEND v7 17/22 ARM: mvebu: Initialize MBus using the DT binding

Now that the mbus device tree binding has been introduced, we can switch over to it.

Also, and since the initialization of the mbus driver is quite fundamental for the system to work properly, this patch adds a BUG() in case mbus fails to initialize.

---
 arch/arm/mach-mvebu/armada-370-xp.c | 34 +---------------------------------
 1 file changed, 1 insertion(+), 33 deletions(-)

arch/arm/mach-mvebu/armada-370-xp.c +1 ~~-33~~

index 97cbb80..829b573 100644
@@ -34,44 +34,12 @@ static void __init armada_370_xp_map_io(void)
 	debug_ll_io_init();
 }
 
-/*
- * This initialization will be replaced by a DT-based
- * initialization once the mvebu-mbus driver gains DT support.
- */
-
-#define ARMADA_370_XP_MBUS_WINS_OFFS   0x20000
-#define ARMADA_370_XP_MBUS_WINS_SIZE   0x100
-#define ARMADA_370_XP_SDRAM_WINS_OFFS  0x20180
-#define ARMADA_370_XP_SDRAM_WINS_SIZE  0x20
-
-static void __init armada_370_xp_mbus_init(void)
-{
-	char *mbus_soc_name;
-	struct device_node *dn;
-	const __be32 mbus_wins_offs = cpu_to_be32(ARMADA_370_XP_MBUS_WINS_OFFS);
-	const __be32 sdram_wins_offs = cpu_to_be32(ARMADA_370_XP_SDRAM_WINS_OFFS);
-
-	if (of_machine_is_compatible("marvell,armada370"))
-		mbus_soc_name = "marvell,armada370-mbus";
-	else
-		mbus_soc_name = "marvell,armadaxp-mbus";
-
-	dn = of_find_node_by_name(NULL, "internal-regs");
-	BUG_ON(!dn);
-
-	mvebu_mbus_init(mbus_soc_name,
-			of_translate_address(dn, &mbus_wins_offs),
-			ARMADA_370_XP_MBUS_WINS_SIZE,
-			of_translate_address(dn, &sdram_wins_offs),
-			ARMADA_370_XP_SDRAM_WINS_SIZE);
-}
-
 static void __init armada_370_xp_timer_and_clk_init(void)
 {
 	of_clk_init(NULL);
 	armada_370_xp_timer_init();
 	coherency_init();
-	armada_370_xp_mbus_init();
+	BUG_ON(mvebu_mbus_dt_init());
 #ifdef CONFIG_CACHE_L2X0
 	l2x0_of_init(0, ~0UL);
 #endif

Signature · 1 line

1.8.1.5

Ezequiel Garcia

author

2013-07-15 14:57 UTC #18 lore raw

PATCH RESEND v7 18/22 ARM: mvebu: Use the preprocessor on Armada 370/XP device tree files

---
 arch/arm/boot/dts/armada-370-db.dts              | 2 +-
 arch/arm/boot/dts/armada-370-mirabox.dts         | 2 +-
 arch/arm/boot/dts/armada-370-rd.dts              | 2 +-
 arch/arm/boot/dts/armada-370.dtsi                | 2 +-
 arch/arm/boot/dts/armada-xp-db.dts               | 2 +-
 arch/arm/boot/dts/armada-xp-gp.dts               | 2 +-
 arch/arm/boot/dts/armada-xp-mv78260.dtsi         | 2 +-
 arch/arm/boot/dts/armada-xp-mv78460.dtsi         | 2 +-
 arch/arm/boot/dts/armada-xp-openblocks-ax3-4.dts | 2 +-
 arch/arm/boot/dts/armada-xp.dtsi                 | 2 +-
 10 files changed, 10 insertions(+), 10 deletions(-)

arch/arm/boot/dts/armada-370-db.dts +1 -1

index beee169..55b986c 100644
@@ -14,7 +14,7 @@
  */
 
 /dts-v1/;
-/include/ "armada-370.dtsi"
+#include "armada-370.dtsi"
 
 / {
 	model = "Marvell Armada 370 Evaluation Board";

arch/arm/boot/dts/armada-370-mirabox.dts +1 -1

index 45b1077..37530af 100644
@@ -9,7 +9,7 @@
  */
 
 /dts-v1/;
-/include/ "armada-370.dtsi"
+#include "armada-370.dtsi"
 
 / {
 	model = "Globalscale Mirabox";

arch/arm/boot/dts/armada-370-rd.dts +1 -1

index a3a2fed..7aa2171 100644
@@ -12,7 +12,7 @@
  */
 
 /dts-v1/;
-/include/ "armada-370.dtsi"
+#include "armada-370.dtsi"
 
 / {
 	model = "Marvell Armada 370 Reference Design";

arch/arm/boot/dts/armada-370.dtsi +1 -1

index fa3dfc6..08ec6e3 100644
@@ -15,7 +15,7 @@
  * common to all Armada SoCs.
  */
 
-/include/ "armada-370-xp.dtsi"
+#include "armada-370-xp.dtsi"
 /include/ "skeleton.dtsi"
 
 / {

arch/arm/boot/dts/armada-xp-db.dts +1 -1

index e28e68f..a9bd766 100644
@@ -14,7 +14,7 @@
  */
 
 /dts-v1/;
-/include/ "armada-xp-mv78460.dtsi"
+#include "armada-xp-mv78460.dtsi"
 
 / {
 	model = "Marvell Armada XP Evaluation Board";

arch/arm/boot/dts/armada-xp-gp.dts +1 -1

index c87b2de..54843e5 100644
@@ -14,7 +14,7 @@
  */
 
 /dts-v1/;
-/include/ "armada-xp-mv78460.dtsi"
+#include "armada-xp-mv78460.dtsi"
 
 / {
 	model = "Marvell Armada XP Development Board DB-MV784MP-GP";

arch/arm/boot/dts/armada-xp-mv78260.dtsi +1 -1

index 2d9335d..985373a 100644
@@ -13,7 +13,7 @@
  * common to all Armada XP SoCs.
  */
 
-/include/ "armada-xp.dtsi"
+#include "armada-xp.dtsi"
 
 / {
 	model = "Marvell Armada XP MV78260 SoC";

arch/arm/boot/dts/armada-xp-mv78460.dtsi +1 -1

index c7b1f4d..f8bf25a 100644
@@ -13,7 +13,7 @@
  * common to all Armada XP SoCs.
  */
 
-/include/ "armada-xp.dtsi"
+#include "armada-xp.dtsi"
 
 / {
 	model = "Marvell Armada XP MV78460 SoC";

arch/arm/boot/dts/armada-xp-openblocks-ax3-4.dts +1 -1

index 8f51045..d090264 100644
@@ -11,7 +11,7 @@
  */
 
 /dts-v1/;
-/include/ "armada-xp-mv78260.dtsi"
+#include "armada-xp-mv78260.dtsi"
 
 / {
 	model = "PlatHome OpenBlocks AX3-4 board";

arch/arm/boot/dts/armada-xp.dtsi +1 -1

index 416eb94..8c07bfe 100644
@@ -16,7 +16,7 @@
  * common to all Armada SoCs.
  */
 
-/include/ "armada-370-xp.dtsi"
+#include "armada-370-xp.dtsi"
 
 / {
 	model = "Marvell Armada XP family SoC";

Signature · 1 line

1.8.1.5

Ezequiel Garcia

author

2013-07-15 14:57 UTC #19 lore raw

PATCH RESEND v7 19/22 ARM: mvebu: Add MBus to Armada 370/XP device tree

The Armada 370/XP SoC family has a completely configurable address space handled by the MBus controller.

This patch introduces the device tree layout of MBus, making the 'soc' node as mbus-compatible.
Since every peripheral/controller is a child of this 'soc' node, this makes all of them sit behind the mbus, thus describing the hardware accurately.

A translation entry has been added for the internal-regs mapping. This can't be done in the common armada-370-xp.dtsi because A370 and AXP have different addressing width.

---
 arch/arm/boot/dts/armada-370-db.dts              |  2 ++
 arch/arm/boot/dts/armada-370-mirabox.dts         |  2 ++
 arch/arm/boot/dts/armada-370-rd.dts              |  2 ++
 arch/arm/boot/dts/armada-370-xp.dtsi             | 15 ++++++++++-----
 arch/arm/boot/dts/armada-370.dtsi                |  4 ++--
 arch/arm/boot/dts/armada-xp-db.dts               |  4 +---
 arch/arm/boot/dts/armada-xp-gp.dts               |  4 +---
 arch/arm/boot/dts/armada-xp-openblocks-ax3-4.dts |  4 +---
 arch/arm/boot/dts/armada-xp.dtsi                 |  2 ++
 9 files changed, 23 insertions(+), 16 deletions(-)

arch/arm/boot/dts/armada-370-db.dts +2 -0

index 55b986c..5920b4e 100644
@@ -30,6 +30,8 @@
 	};
 
 	soc {
+		ranges = <MBUS_ID(0xf0, 0x01) 0 0xd0000000 0x100000>;
+
 		internal-regs {
 			serial at 12000 {
 				clock-frequency = <200000000>;

arch/arm/boot/dts/armada-370-mirabox.dts +2 -0

index 37530af..a4202b6 100644
@@ -25,6 +25,8 @@
 	};
 
 	soc {
+		ranges = <MBUS_ID(0xf0, 0x01) 0 0xd0000000 0x100000>;
+
 		internal-regs {
 			serial at 12000 {
 				clock-frequency = <200000000>;

arch/arm/boot/dts/armada-370-rd.dts +2 -0

index 7aa2171..dd0ba01 100644
@@ -28,6 +28,8 @@
 	};
 
 	soc {
+		ranges = <MBUS_ID(0xf0, 0x01) 0 0xd0000000 0x100000>;
+
 		internal-regs {
 			serial at 12000 {
 				clock-frequency = <200000000>;

arch/arm/boot/dts/armada-370-xp.dtsi +10 -5

index 90b1176..62639b4 100644
@@ -18,6 +18,8 @@
 
 /include/ "skeleton64.dtsi"
 
+#define MBUS_ID(target,attributes) (((target) << 24) | ((attributes) << 16))
+
 / {
 	model = "Marvell Armada 370 and XP SoC";
 	compatible = "marvell,armada-370-xp";

@@ -38,18 +40,21 @@
 	};
 
 	soc {
-		#address-cells = <1>;
+		#address-cells = <2>;
 		#size-cells = <1>;
-		compatible = "simple-bus";
+		controller = <&mbusc>;
 		interrupt-parent = <&mpic>;
-		ranges = <0          0 0xd0000000 0x0100000 /* internal registers */
-			  0xe0000000 0 0xe0000000 0x8100000 /* PCIe */>;
 
 		internal-regs {
 			compatible = "simple-bus";
 			#address-cells = <1>;
 			#size-cells = <1>;
-			ranges;
+			ranges = <0 MBUS_ID(0xf0, 0x01) 0 0x100000>;
+
+			mbusc: mbus-controller at 20000 {
+				compatible = "marvell,mbus-controller";
+				reg = <0x20000 0x100>, <0x20180 0x20>;
+			};
 
 			mpic: interrupt-controller at 20000 {
 				compatible = "marvell,mpic";

arch/arm/boot/dts/armada-370.dtsi +2 -2

index 08ec6e3..4b54e51 100644
@@ -29,8 +29,8 @@
 	};
 
 	soc {
-		ranges = <0          0xd0000000 0x0100000 /* internal registers */
-			  0xe0000000 0xe0000000 0x8100000 /* PCIe */>;
+		compatible = "marvell,armada370-mbus", "simple-bus";
+
 		internal-regs {
 			system-controller at 18200 {
 				compatible = "marvell,armada-370-xp-system-controller";

arch/arm/boot/dts/armada-xp-db.dts +1 -3

index a9bd766..0d4ce54 100644
@@ -30,9 +30,7 @@
 	};
 
 	soc {
-		ranges = <0          0 0xd0000000 0x100000	/* Internal registers 1MiB */
-			  0xe0000000 0 0xe0000000 0x8100000     /* PCIe */
-			  0xf0000000 0 0xf0000000 0x1000000>;	/* Device Bus, NOR 16MiB   */
+		ranges = <MBUS_ID(0xf0, 0x01) 0 0 0xd0000000 0x100000>;
 
 		internal-regs {
 			serial at 12000 {

arch/arm/boot/dts/armada-xp-gp.dts +1 -3

index 54843e5..2fa9209 100644
@@ -39,9 +39,7 @@
 	};
 
 	soc {
-		ranges = <0          0 0xd0000000 0x100000  /* Internal registers 1MiB */
-			  0xe0000000 0 0xe0000000 0x8100000 /* PCIe */
-			  0xf0000000 0 0xf0000000 0x1000000 /* Device Bus, NOR 16MiB  */>;
+		ranges = <MBUS_ID(0xf0, 0x01) 0 0 0xd0000000 0x100000>;
 
 		internal-regs {
 			serial at 12000 {

arch/arm/boot/dts/armada-xp-openblocks-ax3-4.dts +1 -3

index d090264..a3e3a12 100644
@@ -27,9 +27,7 @@
 	};
 
 	soc {
-		ranges = <0          0 0xd0000000 0x100000	/* Internal registers 1MiB */
-			  0xe0000000 0 0xe0000000 0x8100000     /* PCIe */
-			  0xf0000000 0 0xf0000000 0x8000000     /* Device Bus, NOR 128MiB   */>;
+		ranges = <MBUS_ID(0xf0, 0x01) 0 0 0xd0000000 0x100000>;
 
 		internal-regs {
 			serial at 12000 {

arch/arm/boot/dts/armada-xp.dtsi +2 -0

index 8c07bfe..8033824 100644
@@ -27,6 +27,8 @@
 	};
 
 	soc {
+		compatible = "marvell,armadaxp-mbus", "simple-bus";
+
 		internal-regs {
 			L2: l2-cache {
 				compatible = "marvell,aurora-system-cache";

Signature · 1 line

1.8.1.5

Ezequiel Garcia

author

2013-07-15 14:57 UTC #20 lore raw

PATCH RESEND v7 20/22 ARM: mvebu: Add BootROM to Armada 370/XP device tree

In order to access the SoC BootROM, we need to declare a mapping (through a ranges property). The mbus driver will use this property to allocate a suitable address decoding window.

---
 arch/arm/boot/dts/armada-370-db.dts              | 3 ++-
 arch/arm/boot/dts/armada-370-mirabox.dts         | 3 ++-
 arch/arm/boot/dts/armada-370-rd.dts              | 3 ++-
 arch/arm/boot/dts/armada-370.dtsi                | 5 +++++
 arch/arm/boot/dts/armada-xp-db.dts               | 3 ++-
 arch/arm/boot/dts/armada-xp-gp.dts               | 3 ++-
 arch/arm/boot/dts/armada-xp-openblocks-ax3-4.dts | 3 ++-
 arch/arm/boot/dts/armada-xp.dtsi                 | 5 +++++
 8 files changed, 22 insertions(+), 6 deletions(-)

arch/arm/boot/dts/armada-370-db.dts +2 -1

index 5920b4e..90ce29d 100644
@@ -30,7 +30,8 @@
 	};
 
 	soc {
-		ranges = <MBUS_ID(0xf0, 0x01) 0 0xd0000000 0x100000>;
+		ranges = <MBUS_ID(0xf0, 0x01) 0 0xd0000000 0x100000
+			  MBUS_ID(0x01, 0xe0) 0 0xfff00000 0x100000>;
 
 		internal-regs {
 			serial at 12000 {

arch/arm/boot/dts/armada-370-mirabox.dts +2 -1

index a4202b6..19341d2 100644
@@ -25,7 +25,8 @@
 	};
 
 	soc {
-		ranges = <MBUS_ID(0xf0, 0x01) 0 0xd0000000 0x100000>;
+		ranges = <MBUS_ID(0xf0, 0x01) 0 0xd0000000 0x100000
+			  MBUS_ID(0x01, 0xe0) 0 0xfff00000 0x100000>;
 
 		internal-regs {
 			serial at 12000 {

arch/arm/boot/dts/armada-370-rd.dts +2 -1

index dd0ba01..0b3acf3 100644
@@ -28,7 +28,8 @@
 	};
 
 	soc {
-		ranges = <MBUS_ID(0xf0, 0x01) 0 0xd0000000 0x100000>;
+		ranges = <MBUS_ID(0xf0, 0x01) 0 0xd0000000 0x100000
+			  MBUS_ID(0x01, 0xe0) 0 0xfff00000 0x100000>;
 
 		internal-regs {
 			serial at 12000 {

arch/arm/boot/dts/armada-370.dtsi +5 -0

index 4b54e51..bd21d49 100644
@@ -31,6 +31,11 @@
 	soc {
 		compatible = "marvell,armada370-mbus", "simple-bus";
 
+		bootrom {
+			compatible = "marvell,bootrom";
+			reg = <MBUS_ID(0x01, 0xe0) 0 0x100000>;
+		};
+
 		internal-regs {
 			system-controller at 18200 {
 				compatible = "marvell,armada-370-xp-system-controller";

arch/arm/boot/dts/armada-xp-db.dts +2 -1

index 0d4ce54..857f272 100644
@@ -30,7 +30,8 @@
 	};
 
 	soc {
-		ranges = <MBUS_ID(0xf0, 0x01) 0 0 0xd0000000 0x100000>;
+		ranges = <MBUS_ID(0xf0, 0x01) 0 0 0xd0000000 0x100000
+			  MBUS_ID(0x01, 0x1d) 0 0 0xfff00000 0x100000>;
 
 		internal-regs {
 			serial at 12000 {

arch/arm/boot/dts/armada-xp-gp.dts +2 -1

index 2fa9209..934dc46 100644
@@ -39,7 +39,8 @@
 	};
 
 	soc {
-		ranges = <MBUS_ID(0xf0, 0x01) 0 0 0xd0000000 0x100000>;
+		ranges = <MBUS_ID(0xf0, 0x01) 0 0 0xd0000000 0x100000
+			  MBUS_ID(0x01, 0x1d) 0 0 0xfff00000 0x100000>;
 
 		internal-regs {
 			serial at 12000 {

arch/arm/boot/dts/armada-xp-openblocks-ax3-4.dts +2 -1

index a3e3a12..1700f6f 100644
@@ -27,7 +27,8 @@
 	};
 
 	soc {
-		ranges = <MBUS_ID(0xf0, 0x01) 0 0 0xd0000000 0x100000>;
+		ranges = <MBUS_ID(0xf0, 0x01) 0 0 0xd0000000 0x100000
+			  MBUS_ID(0x01, 0x1d) 0 0 0xfff00000 0x100000>;
 
 		internal-regs {
 			serial at 12000 {

arch/arm/boot/dts/armada-xp.dtsi +5 -0

index 8033824..7ba99ce 100644
@@ -29,6 +29,11 @@
 	soc {
 		compatible = "marvell,armadaxp-mbus", "simple-bus";
 
+		bootrom {
+			compatible = "marvell,bootrom";
+			reg = <MBUS_ID(0x01, 0x1d) 0 0x100000>;
+		};
+
 		internal-regs {
 			L2: l2-cache {
 				compatible = "marvell,aurora-system-cache";

Signature · 1 line

1.8.1.5

Ezequiel Garcia

author

2013-07-15 14:57 UTC #21 lore raw

PATCH RESEND v7 21/22 ARM: mvebu: Relocate Armada 370/XP DeviceBus device tree nodes

Now that mbus has been added to the device tree, it's possible to move the DeviceBus out of internal registers, placing it directly below the mbus. This is a more accurate representation of the hardware.

---
 arch/arm/boot/dts/armada-370-xp.dtsi             | 94 +++++++++++++-----------
 arch/arm/boot/dts/armada-xp-db.dts               | 59 +++++++--------
 arch/arm/boot/dts/armada-xp-gp.dts               | 60 +++++++--------
 arch/arm/boot/dts/armada-xp-openblocks-ax3-4.dts | 65 ++++++++--------
 4 files changed, 140 insertions(+), 138 deletions(-)

arch/arm/boot/dts/armada-370-xp.dtsi +50 ~~-44~~

index 62639b4..073dd20 100644
@@ -45,6 +45,56 @@
 		controller = <&mbusc>;
 		interrupt-parent = <&mpic>;
 
+		devbus-bootcs {
+			compatible = "marvell,mvebu-devbus";
+			reg = <MBUS_ID(0xf0, 0x01) 0x10400 0x8>;
+			ranges = <0 MBUS_ID(0x01, 0x2f) 0 0xffffffff>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			clocks = <&coreclk 0>;
+			status = "disabled";
+		};
+
+		devbus-cs0 {
+			compatible = "marvell,mvebu-devbus";
+			reg = <MBUS_ID(0xf0, 0x01) 0x10408 0x8>;
+			ranges = <0 MBUS_ID(0x01, 0x3e) 0 0xffffffff>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			clocks = <&coreclk 0>;
+			status = "disabled";
+		};
+
+		devbus-cs1 {
+			compatible = "marvell,mvebu-devbus";
+			reg = <MBUS_ID(0xf0, 0x01) 0x10410 0x8>;
+			ranges = <0 MBUS_ID(0x01, 0x3d) 0 0xffffffff>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			clocks = <&coreclk 0>;
+			status = "disabled";
+		};
+
+		devbus-cs2 {
+			compatible = "marvell,mvebu-devbus";
+			reg = <MBUS_ID(0xf0, 0x01) 0x10418 0x8>;
+			ranges = <0 MBUS_ID(0x01, 0x3b) 0 0xffffffff>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			clocks = <&coreclk 0>;
+			status = "disabled";
+		};
+
+		devbus-cs3 {
+			compatible = "marvell,mvebu-devbus";
+			reg = <MBUS_ID(0xf0, 0x01) 0x10420 0x8>;
+			ranges = <0 MBUS_ID(0x01, 0x37) 0 0xffffffff>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			clocks = <&coreclk 0>;
+			status = "disabled";
+		};
+
 		internal-regs {
 			compatible = "simple-bus";
 			#address-cells = <1>;

@@ -200,50 +250,6 @@
 				status = "disabled";
 			};
 
-			devbus-bootcs at 10400 {
-				compatible = "marvell,mvebu-devbus";
-				reg = <0x10400 0x8>;
-				#address-cells = <1>;
-				#size-cells = <1>;
-				clocks = <&coreclk 0>;
-				status = "disabled";
-			};
-
-			devbus-cs0 at 10408 {
-				compatible = "marvell,mvebu-devbus";
-				reg = <0x10408 0x8>;
-				#address-cells = <1>;
-				#size-cells = <1>;
-				clocks = <&coreclk 0>;
-				status = "disabled";
-			};
-
-			devbus-cs1 at 10410 {
-				compatible = "marvell,mvebu-devbus";
-				reg = <0x10410 0x8>;
-				#address-cells = <1>;
-				#size-cells = <1>;
-				clocks = <&coreclk 0>;
-				status = "disabled";
-			};
-
-			devbus-cs2 at 10418 {
-				compatible = "marvell,mvebu-devbus";
-				reg = <0x10418 0x8>;
-				#address-cells = <1>;
-				#size-cells = <1>;
-				clocks = <&coreclk 0>;
-				status = "disabled";
-			};
-
-			devbus-cs3 at 10420 {
-				compatible = "marvell,mvebu-devbus";
-				reg = <0x10420 0x8>;
-				#address-cells = <1>;
-				#size-cells = <1>;
-				clocks = <&coreclk 0>;
-				status = "disabled";
-			};
 		};
 	};
  };

arch/arm/boot/dts/armada-xp-db.dts +30 ~~-29~~

71 lines not on this page · raw message

arch/arm/boot/dts/armada-xp-gp.dts +30 ~~-30~~

72 lines not on this page · raw message

arch/arm/boot/dts/armada-xp-openblocks-ax3-4.dts +30 ~~-35~~

77 lines not on this page · raw message

Signature · 1 line

1.8.1.5

Ezequiel Garcia

author

2013-07-15 14:57 UTC #22 lore raw

PATCH RESEND v7 22/22 ARM: mvebu: Relocate Armada 370/XP PCIe device tree nodes

Now that mbus has been added to the device tree, it's possible to move the PCIe nodes out of internal registers, placing it directly below the mbus. This is a more accurate representation of the hardware.

Moving the PCIe nodes, we now need to introduce an extra cell to encode the window target ID and attribute. Since this depends on the PCIe port, we split the ranges translation entries, to correspond to each MBus window.

---
 arch/arm/boot/dts/armada-370-mirabox.dts         |  32 +-
 arch/arm/boot/dts/armada-370-xp.dtsi             |   2 +
 arch/arm/boot/dts/armada-370.dtsi                | 101 +++---
 arch/arm/boot/dts/armada-xp-db.dts               |  67 ++--
 arch/arm/boot/dts/armada-xp-gp.dts               |  42 +--
 arch/arm/boot/dts/armada-xp-mv78230.dtsi         | 222 ++++++------
 arch/arm/boot/dts/armada-xp-mv78260.dtsi         | 261 ++++++++-------
 arch/arm/boot/dts/armada-xp-mv78460.dtsi         | 409 ++++++++++++-----------
 arch/arm/boot/dts/armada-xp-openblocks-ax3-4.dts |  18 +-
 9 files changed, 612 insertions(+), 542 deletions(-)

arch/arm/boot/dts/armada-370-mirabox.dts +16 ~~-16~~

index 19341d2..2471d9d 100644
@@ -28,6 +28,22 @@
 		ranges = <MBUS_ID(0xf0, 0x01) 0 0xd0000000 0x100000
 			  MBUS_ID(0x01, 0xe0) 0 0xfff00000 0x100000>;
 
+		pcie-controller {
+			status = "okay";
+
+			/* Internal mini-PCIe connector */
+			pcie at 1,0 {
+				/* Port 0, Lane 0 */
+				status = "okay";
+			};
+
+			/* Connected on the PCB to a USB 3.0 XHCI controller */
+			pcie at 2,0 {
+				/* Port 1, Lane 0 */
+				status = "okay";
+			};
+		};
+
 		internal-regs {
 			serial at 12000 {
 				clock-frequency = <200000000>;

@@ -123,22 +139,6 @@
 					reg = <0x25>;
 				};
 			};
-
-			pcie-controller {
-				status = "okay";
-
-				/* Internal mini-PCIe connector */
-				pcie at 1,0 {
-					/* Port 0, Lane 0 */
-					status = "okay";
-				};
-
-				/* Connected on the PCB to a USB 3.0 XHCI controller */
-				pcie at 2,0 {
-					/* Port 1, Lane 0 */
-					status = "okay";
-				};
-			};
 		};
 	};
 };

arch/arm/boot/dts/armada-370-xp.dtsi +2 -0

index 073dd20..e984ce6 100644
@@ -44,6 +44,8 @@
 		#size-cells = <1>;
 		controller = <&mbusc>;
 		interrupt-parent = <&mpic>;
+		pcie-mem-aperture = <0xe0000000 0x8000000>;
+		pcie-io-aperture  = <0xe8000000 0x100000>;
 
 		devbus-bootcs {
 			compatible = "marvell,mvebu-devbus";

arch/arm/boot/dts/armada-370.dtsi +53 ~~-48~~

113 lines not on this page · raw message

arch/arm/boot/dts/armada-xp-db.dts +33 ~~-34~~

79 lines not on this page · raw message

arch/arm/boot/dts/armada-xp-gp.dts +21 ~~-21~~

54 lines not on this page · raw message

arch/arm/boot/dts/armada-xp-mv78230.dtsi +118 ~~-104~~

234 lines not on this page · raw message

arch/arm/boot/dts/armada-xp-mv78260.dtsi +139 ~~-122~~

273 lines not on this page · raw message

arch/arm/boot/dts/armada-xp-mv78460.dtsi +221 ~~-188~~

421 lines not on this page · raw message

arch/arm/boot/dts/armada-xp-openblocks-ax3-4.dts +9 -9

index 2b60ee0..5695afc 100644
@@ -59,6 +59,15 @@
 			};
 		};
 
+		pcie-controller {
+			status = "okay";
+			/* Internal mini-PCIe connector */
+			pcie at 1,0 {
+				/* Port 0, Lane 0 */
+				status = "okay";
+			};
+		};
+
 		internal-regs {
 			serial at 12000 {
 				clock-frequency = <250000000>;

@@ -176,15 +185,6 @@
 			usb at 51000 {
 				status = "okay";
 			};
-
-			pcie-controller {
-				status = "okay";
-				/* Internal mini-PCIe connector */
-				pcie at 1,0 {
-					/* Port 0, Lane 0 */
-					status = "okay";
-				};
-			};
 		};
 	};
 };

Signature · 1 line

1.8.1.5

Ezequiel Garcia

author

2013-07-20 15:44 UTC #23 lore raw

v7 cover MBus DT binding: The return of PCIe

Hi Grant, Arnd, Jason:

Quoted 12 lines · Ezequiel Garcia

Here's the new MBus DT binding, implementing the changes proposed by Thomas when we discussed the previous patchset:
http://www.spinics.net/lists/arm-kernel/msg257170.html
As far as I know, this round fixes *all* the concerns raised in the past and therefore I'd like to get Acked-by's from all the parties involved on the respective patches, and particularly for the DT binding.
If there's anything left to review, we'll be glad to fix it quickly, so don't hesitate in providing your feedback!

Can you comment on this DT binding? Notice this is the outcome of a lengthy discussion and has been already agreed by Arnd and Jason Gunthorpe.

If it looks OK, I'd like to have formal Acked-by's so Jason Cooper can merge it.

On the other side, given we've decided to mark some bindings as 'unstable' or 'staging' maybe Jason can merge it so it can be in linux-next. This way developers can actually start using this, and complaining if there's anything to complain.

If we leave it as a patchset floating in mailing-lists it's hardly going to get tested.

Does this approach make sense?

Thanks a lot!

Signature · 3 lines

Ezequiel Garc?a, Free Electrons
Embedded Linux, Kernel and Android Engineering
http://free-electrons.com

Andrew Lunn

maintainer

2013-07-20 16:58 UTC #24 lore raw

v7 cover MBus DT binding: The return of PCIe