Skip to contentSkip to conversation

Add tested id switch and vbus connect detect support for Chipidea

PATCH Superseded Peter Chen 3 participants 20 messages Jul 26, 2013 – Jul 31, 2013

Subsystems (3)

v13 of 15 Superseded Latest is v15 →

lore
Share & tools
lore

Peter Chen

author
#0 lore raw

v13 cover Add tested id switch and vbus connect detect support for Chipidea

This patchset adds tested otg id switch function and vbus connect and disconnect detection for chipidea driver. And fix kinds of bugs found at chipidea drivers after enabling id and vbus detection.

This patch are fully tested at imx6 sabresd and imx28evk platform by me. Besides, marek tested it on two STMP3780-based boards (not yet mainline) and two MX28-based boards.

My chipidea repo: https://github.com/hzpeterchen/linux-usb.git

Chagnes for v13:
- Add Tested-by: Marek Vasut <[email protected]>
- [Sascha's comments]: Add return value check for devm_regulator_get. [3/14]
- [Marc's comments]: Change timeout usage at hw_wait_reg. [11/14]
- [Alex's comments]: Using platdata flag to indicate dual role but not OTG controller. [7/14]

Changes for v12:
- Rebased greg's usb-next tree (3.10.0-rc7+)
- Split more small patches for single function and fix.

Changes for v11:
- mark ci_handle_vbus_change as static as it is only used at core.c [3/9]
- Move the vbus operation for platform code to host code, as vbus operation is common operation, and host is the only user for vbus. When it is host mode, we need to open vbus, when it is out of host mode, we need to close vbus. [6/9] [8/9]
- Delete the delayed work at core.c as it is not needed. [7/9]

Changes for v10:
- Delete [8/9] at v9, ci core's drvdata must be set for further operation. [8/8]

Changes for v9:
- Some small comments from Alex like: variable comment for otg event additional newline. [3/9]
- Import function tell show if the controller has otg capable, if the controller supports both host and device, we think it is otg capable, and can read OTGSC. [3/9]
- Merge two otg patches [v8 3/8] and [v8 4/8] to one [v9 3/9]. [3/9]
- Add inline to ci_hdrc_gadget_destroy if CONFIG_USB_CHIPIDEA_UDC is not defined, it can fix one build warning "defined but not used" [3/9]
- One comment from Felipe about changing calling gadget disconnect API at chipidea's udc driver. I move calling ci->driver->disconnect from _gadget_stop_activity to which calls _gadget_stop_activity except ci13xxx_stop, as udc core will call disconnect when do rmmod gadget. [7/9]
- Add ci core probe's return value to ci's platform_data, we do this for getting core's probe's result at platform layer, and quit it if the core's probe fails. [8/9] [9/9]

Changes for v8:
- Add ci_supports_gadget helper to know if the controller supports gadget, if the controller supports gadget, it needs to read otgsc to know the vbus value, basically, if the controller supports gadget, it will support host as well [3/8]
- At ci_hdrc_probe, it needs to add free memory at error path [3/8]
- Cosolidate ci->driver = NULL at ci13xxx_stop [8/8]

Changes for v7:
For Patch 8/8, we only need to set ci->driver to NULL when usb cable is not connected, for other changes, it will case some runtime pm unmatch and un-align with udc-core & composite driver problems.

Changes for v6:
- Add Alex comments for init/destroy function [3/8] [4/8]
- Remove memset(&ci->gadget, 0, sizeof(ci->gadget)) at destory function [4/8]
- Add Kishon's comment: Change the format of struct usb_otg otg at drivers/usb/chipidea/ci.h [1/8]
- Add comments for CI_VBUS_STABLE_TIMEOUT [3/8]
- Change the otg_set_peripheral return value check as the fully
chipidea driver users don't need it. [4/8]
- Fix one bug that the oops when re-plug in usb cable after
rmmod gadget [8/8]

Peter Chen (14):
usb: chipidea: add vbus regulator control
usb: chipidea: imx: remove vbus regulator operation
usb: chipidea: imx: add return value check for devm_regulator_get
usb: chipidea: udc: otg_set_peripheral is useless for some chipidea
users
usb: chipidea: otg: Add otg file used to access otgsc
usb: chipidea: Add role init and destory APIs
usb: chipidea: add flag CI_HDRC_DUAL_ROLE_NOT_OTG
usb: chipidea: disable all interrupts and clear all interrupts status
usb: chipidea: move otg relate things to otg file
usb: chipidea: add vbus interrupt handler
usb: chipidea: add wait vbus lower than OTGSC_BSV before role starts
usb: chipidea: udc: misuse flag CI_HDRC_REGS_SHARED and
CI_HDRC_PULLUP_ON_VBUS
usb: chipidea: udc: .pullup is valid when vbus is on at
CI_HDRC_PULLUP_ON_VBUS
usb: chipidea: udc: fix the oops when plugs in usb cable after rmmod
gadget

 drivers/usb/chipidea/Makefile      |    2 +-
 drivers/usb/chipidea/bits.h        |   10 ++
 drivers/usb/chipidea/ci.h          |    8 ++
 drivers/usb/chipidea/ci_hdrc_imx.c |   40 ++++-----
 drivers/usb/chipidea/core.c        |  161 ++++++++++++++++++++++++------------
 drivers/usb/chipidea/host.c        |   30 +++++++-
 drivers/usb/chipidea/host.h        |    6 ++
 drivers/usb/chipidea/otg.c         |  135 ++++++++++++++++++++++++++++++
 drivers/usb/chipidea/otg.h         |   22 +++++
 drivers/usb/chipidea/udc.c         |   72 ++++++++++++----
 drivers/usb/chipidea/udc.h         |    6 ++
 include/linux/usb/chipidea.h       |    6 ++
 12 files changed, 402 insertions(+), 96 deletions(-)
 create mode 100644 drivers/usb/chipidea/otg.c
 create mode 100644 drivers/usb/chipidea/otg.h
author
#1 lore raw

PATCH v13 1/14 usb: chipidea: add vbus regulator control

For boards which have board level vbus control (eg, through gpio), we need to vbus operation according to below rules:
- For host, we need open vbus before start hcd, and close it after remove hcd.
- For otg, the vbus needs to be on/off when usb role switches. When the host roles begins, it opens vbus; when the host role finishes, it closes vbus.

We put vbus operation to host as host is the only vbus user, When we are at host mode, the vbus is on, when we are not at host mode, vbus should be off.

---
 drivers/usb/chipidea/host.c  |   23 ++++++++++++++++++++++-
 include/linux/usb/chipidea.h |    1 +
 2 files changed, 23 insertions(+), 1 deletions(-)
drivers/usb/chipidea/host.c +22 -1
index 40d0fda..e94e52b 100644
@@ -24,6 +24,7 @@
 #include <linux/usb.h>
 #include <linux/usb/hcd.h>
 #include <linux/usb/chipidea.h>
+#include <linux/regulator/consumer.h>
 
 #include "../host/ehci.h"
 
@@ -64,9 +65,19 @@ static int host_start(struct ci_hdrc *ci)
 	ehci->caps = ci->hw_bank.cap;
 	ehci->has_hostpc = ci->hw_bank.lpm;
 
+	if (ci->platdata->reg_vbus) {
+		ret = regulator_enable(ci->platdata->reg_vbus);
+		if (ret) {
+			dev_err(ci->dev,
+				"Failed to enable vbus regulator, ret=%d\n",
+				ret);
+			goto put_hcd;
+		}
+	}
+
 	ret = usb_add_hcd(hcd, 0, 0);
 	if (ret)
-		usb_put_hcd(hcd);
+		goto disable_reg;
 	else
 		ci->hcd = hcd;
 
@@ -74,6 +85,14 @@ static int host_start(struct ci_hdrc *ci)
 		hw_write(ci, OP_USBMODE, USBMODE_CI_SDIS, USBMODE_CI_SDIS);
 
 	return ret;
+
+disable_reg:
+	regulator_disable(ci->platdata->reg_vbus);
+
+put_hcd:
+	usb_put_hcd(hcd);
+
+	return ret;
 }
 
 static void host_stop(struct ci_hdrc *ci)
@@ -82,6 +101,8 @@ static void host_stop(struct ci_hdrc *ci)
 
 	usb_remove_hcd(hcd);
 	usb_put_hcd(hcd);
+	if (ci->platdata->reg_vbus)
+		regulator_disable(ci->platdata->reg_vbus);
 }
 
 int ci_hdrc_host_init(struct ci_hdrc *ci)
include/linux/usb/chipidea.h +1 -0
index 2562994..118bf66 100644
@@ -24,6 +24,7 @@ struct ci_hdrc_platform_data {
 #define CI_HDRC_CONTROLLER_RESET_EVENT		0
 #define CI_HDRC_CONTROLLER_STOPPED_EVENT	1
 	void	(*notify_event) (struct ci_hdrc *ci, unsigned event);
+	struct regulator *reg_vbus;
 };
 
 /* Default offset of capability registers */
Signature · 1 line
1.7.0.4
author
#2 lore raw

PATCH v13 2/14 usb: chipidea: imx: remove vbus regulator operation

In reply to Peter Chen

Since we have added vbus reguatlor operation at common host file (chipidea/host.c), the glue layer vbus operation isn't needed any more.

---
 drivers/usb/chipidea/ci_hdrc_imx.c |   30 +++++++-----------------------
 1 files changed, 7 insertions(+), 23 deletions(-)
drivers/usb/chipidea/ci_hdrc_imx.c +7 -23
index 14362c0..d06355e 100644
@@ -31,7 +31,6 @@ struct ci_hdrc_imx_data {
 	struct usb_phy *phy;
 	struct platform_device *ci_pdev;
 	struct clk *clk;
-	struct regulator *reg_vbus;
 };
 
 static const struct usbmisc_ops *usbmisc_ops;
@@ -141,22 +140,13 @@ static int ci_hdrc_imx_probe(struct platform_device *pdev)
 		goto err_clk;
 	}
 
-	/* we only support host now, so enable vbus here */
-	data->reg_vbus = devm_regulator_get(&pdev->dev, "vbus");
-	if (!IS_ERR(data->reg_vbus)) {
-		ret = regulator_enable(data->reg_vbus);
-		if (ret) {
-			dev_err(&pdev->dev,
-				"Failed to enable vbus regulator, err=%d\n",
-				ret);
-			goto err_clk;
-		}
-	} else {
-		data->reg_vbus = NULL;
-	}
-
 	pdata.phy = data->phy;
 
+	/* Get the vbus regulator */
+	pdata.reg_vbus = devm_regulator_get(&pdev->dev, "vbus");
+	if (IS_ERR(pdata.reg_vbus))
+		pdata.reg_vbus = NULL;
+
 	if (!pdev->dev.dma_mask)
 		pdev->dev.dma_mask = &pdev->dev.coherent_dma_mask;
 	if (!pdev->dev.coherent_dma_mask)
@@ -167,7 +157,7 @@ static int ci_hdrc_imx_probe(struct platform_device *pdev)
 		if (ret) {
 			dev_err(&pdev->dev,
 				"usbmisc init failed, ret=%d\n", ret);
-			goto err;
+			goto err_clk;
 		}
 	}
 
@@ -179,7 +169,7 @@ static int ci_hdrc_imx_probe(struct platform_device *pdev)
 		dev_err(&pdev->dev,
 			"Can't register ci_hdrc platform device, err=%d\n",
 			ret);
-		goto err;
+		goto err_clk;
 	}
 
 	if (usbmisc_ops && usbmisc_ops->post) {
@@ -200,9 +190,6 @@ static int ci_hdrc_imx_probe(struct platform_device *pdev)
 
 disable_device:
 	ci_hdrc_remove_device(data->ci_pdev);
-err:
-	if (data->reg_vbus)
-		regulator_disable(data->reg_vbus);
 err_clk:
 	clk_disable_unprepare(data->clk);
 	return ret;
@@ -215,9 +202,6 @@ static int ci_hdrc_imx_remove(struct platform_device *pdev)
 	pm_runtime_disable(&pdev->dev);
 	ci_hdrc_remove_device(data->ci_pdev);
 
-	if (data->reg_vbus)
-		regulator_disable(data->reg_vbus);
-
 	if (data->phy) {
 		usb_phy_shutdown(data->phy);
 		module_put(data->phy->dev->driver->owner);
Signature · 1 line
1.7.0.4
#3 lore raw

PATCH v13 2/14 usb: chipidea: imx: remove vbus regulator operation

Hi Peter,

Quoted 37 lines · Peter Chen

Since we have added vbus reguatlor operation at common host file (chipidea/host.c), the glue layer vbus operation isn't needed any more.

---
 drivers/usb/chipidea/ci_hdrc_imx.c |   30 +++++++-----------------------
 1 files changed, 7 insertions(+), 23 deletions(-)
drivers/usb/chipidea/ci_hdrc_imx.c +0 -12
index 14362c0..d06355e 100644
@@ -31,7 +31,6 @@ struct ci_hdrc_imx_data {
 	struct usb_phy *phy;
 	struct platform_device *ci_pdev;
 	struct clk *clk;
-	struct regulator *reg_vbus;
 };
 
 static const struct usbmisc_ops *usbmisc_ops;
@@ -141,22 +140,13 @@ static int ci_hdrc_imx_probe(struct platform_device *pdev)
 		goto err_clk;
 	}
 
-	/* we only support host now, so enable vbus here */
-	data->reg_vbus = devm_regulator_get(&pdev->dev, "vbus");
-	if (!IS_ERR(data->reg_vbus)) {
-		ret = regulator_enable(data->reg_vbus);
-		if (ret) {
-			dev_err(&pdev->dev,
-				"Failed to enable vbus regulator, err=%d\n",
-				ret);
-			goto err_clk;
-		}
-	} else {

drivers/usb/chipidea/ci_hdrc_imx.c static int ci_hdrc_imx_probe(struct platform_device *pdev) · line 149

Quoted 10 lines
drivers/usb/chipidea/ci_hdrc_imx.c +5 -3
-		data->reg_vbus = NULL;
-	}
-
 	pdata.phy = data->phy;
 
+	/* Get the vbus regulator */
+	pdata.reg_vbus = devm_regulator_get(&pdev->dev, "vbus");
+	if (IS_ERR(pdata.reg_vbus))
+		pdata.reg_vbus = NULL;
+

This hunk needs the reg_vbus variable from the previous patch, therefor it should also be added in that patch. As the user of the variable is the previous patch, it's the reason to swap their order.

Anyway, can't this be done in core.c instead? I don't see why other users don't need this code.

Quoted 46 lines
drivers/usb/chipidea/ci_hdrc_imx.c +2 -8
 	if (!pdev->dev.dma_mask)
 		pdev->dev.dma_mask = &pdev->dev.coherent_dma_mask;
 	if (!pdev->dev.coherent_dma_mask)
@@ -167,7 +157,7 @@ static int ci_hdrc_imx_probe(struct platform_device *pdev)
 		if (ret) {
 			dev_err(&pdev->dev,
 				"usbmisc init failed, ret=%d\n", ret);
-			goto err;
+			goto err_clk;
 		}
 	}
 
@@ -179,7 +169,7 @@ static int ci_hdrc_imx_probe(struct platform_device *pdev)
 		dev_err(&pdev->dev,
 			"Can't register ci_hdrc platform device, err=%d\n",
 			ret);
-		goto err;
+		goto err_clk;
 	}
 
 	if (usbmisc_ops && usbmisc_ops->post) {
@@ -200,9 +190,6 @@ static int ci_hdrc_imx_probe(struct platform_device *pdev)
 
 disable_device:
 	ci_hdrc_remove_device(data->ci_pdev);
-err:
-	if (data->reg_vbus)
-		regulator_disable(data->reg_vbus);
 err_clk:
 	clk_disable_unprepare(data->clk);
 	return ret;
@@ -215,9 +202,6 @@ static int ci_hdrc_imx_remove(struct platform_device *pdev)
 	pm_runtime_disable(&pdev->dev);
 	ci_hdrc_remove_device(data->ci_pdev);
 
-	if (data->reg_vbus)
-		regulator_disable(data->reg_vbus);
-
 	if (data->phy) {
 		usb_phy_shutdown(data->phy);
 		module_put(data->phy->dev->driver->owner);
Signature · 1 line
1.7.0.4
Signature · 4 lines
Pengutronix e.K.                           |                             |
Industrial Linux Solutions                 | http://www.pengutronix.de/  |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |
author
#4 lore raw

PATCH v13 2/14 usb: chipidea: imx: remove vbus regulator operation

Quoted 45 lines · Michael Grzeschik

Hi Peter,

Quoted 42 lines · Peter Chen

Since we have added vbus reguatlor operation at common host file (chipidea/host.c), the glue layer vbus operation isn't needed any more.

---
 drivers/usb/chipidea/ci_hdrc_imx.c |   30 +++++++-----------------------
 1 files changed, 7 insertions(+), 23 deletions(-)
drivers/usb/chipidea/ci_hdrc_imx.c +0 -15
index 14362c0..d06355e 100644
@@ -31,7 +31,6 @@ struct ci_hdrc_imx_data {
 	struct usb_phy *phy;
 	struct platform_device *ci_pdev;
 	struct clk *clk;
-	struct regulator *reg_vbus;
 };
 
 static const struct usbmisc_ops *usbmisc_ops;
@@ -141,22 +140,13 @@ static int ci_hdrc_imx_probe(struct platform_device *pdev)
 		goto err_clk;
 	}
 
-	/* we only support host now, so enable vbus here */
-	data->reg_vbus = devm_regulator_get(&pdev->dev, "vbus");
-	if (!IS_ERR(data->reg_vbus)) {
-		ret = regulator_enable(data->reg_vbus);
-		if (ret) {
-			dev_err(&pdev->dev,
-				"Failed to enable vbus regulator, err=%d\n",
-				ret);
-			goto err_clk;
-		}
-	} else {
-		data->reg_vbus = NULL;
-	}
-
 	pdata.phy = data->phy;
 
Quoted 10 lines

drivers/usb/chipidea/ci_hdrc_imx.c static int ci_hdrc_imx_probe(struct platform_device *pdev) · line 149

Quoted 5 lines
drivers/usb/chipidea/ci_hdrc_imx.c +5 -0
+	/* Get the vbus regulator */
+	pdata.reg_vbus = devm_regulator_get(&pdev->dev, "vbus");
+	if (IS_ERR(pdata.reg_vbus))
+		pdata.reg_vbus = NULL;
+

This hunk needs the reg_vbus variable from the previous patch, therefor it should also be added in that patch. As the user of the variable is the previous patch, it's the reason to swap their order.

The [1/14] implements the vbus operation at common code (host.c) This one [2/14] implements how the glue layer get the vbus.

I am OK to swap above two, but I still can't see obvious reason.

Quoted 3 lines

Anyway, can't this be done in core.c instead? I don't see why other users don't need this code.

We still not implement DT support at core.c, it is a big job, this is the main reason, besides, Alex prefers platform things at glue layer.

Signature · 2 lines
Best Regards,
Peter Chen
author
#5 lore raw

PATCH v13 3/14 usb: chipidea: imx: add return value check for devm_regulator_get

In reply to Peter Chen

- If devm_regulator_get returns -EPROBE_DEFER, we also return -EPROBE_DEFER to wait regulator being ready later.
- If devm_regulator_get returns -ENODEV, we think there is no "vbus-supply" node at DT, it means this board doesn't need vbus control.
- If devm_regulator_get returns other error values, it means there are something wrong for getting this regulator.

---
 drivers/usb/chipidea/ci_hdrc_imx.c |   14 ++++++++++++--
 1 files changed, 12 insertions(+), 2 deletions(-)
drivers/usb/chipidea/ci_hdrc_imx.c +12 -2
index d06355e..0ced8c1 100644
@@ -144,8 +144,18 @@ static int ci_hdrc_imx_probe(struct platform_device *pdev)
 
 	/* Get the vbus regulator */
 	pdata.reg_vbus = devm_regulator_get(&pdev->dev, "vbus");
-	if (IS_ERR(pdata.reg_vbus))
-		pdata.reg_vbus = NULL;
+	if (PTR_ERR(pdata.reg_vbus) == -EPROBE_DEFER) {
+		ret = -EPROBE_DEFER;
+		goto err_clk;
+	} else if (PTR_ERR(pdata.reg_vbus) == -ENODEV) {
+		pdata.reg_vbus = NULL; /* no vbus regualator is needed */
+	} else if (IS_ERR(pdata.reg_vbus)) {
+		dev_err(&pdev->dev,
+				"Getting regulator error: %ld\n",
+					PTR_ERR(pdata.reg_vbus));
+		ret = PTR_ERR(pdata.reg_vbus);
+		goto err_clk;
+	}
 
 	if (!pdev->dev.dma_mask)
 		pdev->dev.dma_mask = &pdev->dev.coherent_dma_mask;
Signature · 1 line
1.7.0.4
#6 lore raw

PATCH v13 3/14 usb: chipidea: imx: add return value check for devm_regulator_get

Quoted 29 lines · Peter Chen

- If devm_regulator_get returns -EPROBE_DEFER, we also return -EPROBE_DEFER to wait regulator being ready later.
- If devm_regulator_get returns -ENODEV, we think there is no "vbus-supply" node at DT, it means this board doesn't need vbus control.
- If devm_regulator_get returns other error values, it means there are something wrong for getting this regulator.

---
 drivers/usb/chipidea/ci_hdrc_imx.c |   14 ++++++++++++--
 1 files changed, 12 insertions(+), 2 deletions(-)
drivers/usb/chipidea/ci_hdrc_imx.c +5 -2
index d06355e..0ced8c1 100644
@@ -144,8 +144,18 @@ static int ci_hdrc_imx_probe(struct platform_device *pdev)
 
 	/* Get the vbus regulator */
 	pdata.reg_vbus = devm_regulator_get(&pdev->dev, "vbus");
-	if (IS_ERR(pdata.reg_vbus))
-		pdata.reg_vbus = NULL;
+	if (PTR_ERR(pdata.reg_vbus) == -EPROBE_DEFER) {
+		ret = -EPROBE_DEFER;
+		goto err_clk;
+	} else if (PTR_ERR(pdata.reg_vbus) == -ENODEV) {
+		pdata.reg_vbus = NULL; /* no vbus regualator is needed */

drivers/usb/chipidea/ci_hdrc_imx.c static int ci_hdrc_imx_probe(struct platform_device *pdev) · line 161

Quoted 10 lines
drivers/usb/chipidea/ci_hdrc_imx.c +7 -0
+	} else if (IS_ERR(pdata.reg_vbus)) {
+		dev_err(&pdev->dev,
+				"Getting regulator error: %ld\n",
+					PTR_ERR(pdata.reg_vbus));
+		ret = PTR_ERR(pdata.reg_vbus);
+		goto err_clk;
+	}
 
 	if (!pdev->dev.dma_mask)
 		pdev->dev.dma_mask = &pdev->dev.coherent_dma_mask;

This is wrong, you should squash that into the previous patch. And as already mentioned, this can probably go into core.c as well.

Pick up the habit *not* to change code in one series which another patch of the same series introduced. This only adds *dusty* unused history in the patchstack that nobody needs. A *clean* and *coherent* series with discrete patches is much easier to review and will get accepted much faster.

Michael

Signature · 4 lines
Pengutronix e.K.                           |                             |
Industrial Linux Solutions                 | http://www.pengutronix.de/  |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |
author
#7 lore raw

PATCH v13 3/14 usb: chipidea: imx: add return value check for devm_regulator_get

Quoted 44 lines · Michael Grzeschik
Quoted 29 lines · Peter Chen

- If devm_regulator_get returns -EPROBE_DEFER, we also return -EPROBE_DEFER to wait regulator being ready later.
- If devm_regulator_get returns -ENODEV, we think there is no "vbus-supply" node at DT, it means this board doesn't need vbus control.
- If devm_regulator_get returns other error values, it means there are something wrong for getting this regulator.

---
 drivers/usb/chipidea/ci_hdrc_imx.c |   14 ++++++++++++--
 1 files changed, 12 insertions(+), 2 deletions(-)
drivers/usb/chipidea/ci_hdrc_imx.c +5 -2
index d06355e..0ced8c1 100644
@@ -144,8 +144,18 @@ static int ci_hdrc_imx_probe(struct platform_device *pdev)
 
 	/* Get the vbus regulator */
 	pdata.reg_vbus = devm_regulator_get(&pdev->dev, "vbus");
-	if (IS_ERR(pdata.reg_vbus))
-		pdata.reg_vbus = NULL;
+	if (PTR_ERR(pdata.reg_vbus) == -EPROBE_DEFER) {
+		ret = -EPROBE_DEFER;
+		goto err_clk;
+	} else if (PTR_ERR(pdata.reg_vbus) == -ENODEV) {
+		pdata.reg_vbus = NULL; /* no vbus regualator is needed */

drivers/usb/chipidea/ci_hdrc_imx.c static int ci_hdrc_imx_probe(struct platform_device *pdev) · line 161

Quoted 10 lines
drivers/usb/chipidea/ci_hdrc_imx.c +7 -0
+	} else if (IS_ERR(pdata.reg_vbus)) {
+		dev_err(&pdev->dev,
+				"Getting regulator error: %ld\n",
+					PTR_ERR(pdata.reg_vbus));
+		ret = PTR_ERR(pdata.reg_vbus);
+		goto err_clk;
+	}
 
 	if (!pdev->dev.dma_mask)
 		pdev->dev.dma_mask = &pdev->dev.coherent_dma_mask;

This is wrong, you should squash that into the previous patch. And as already mentioned, this can probably go into core.c as well.

Quoted 5 lines

Pick up the habit *not* to change code in one series which another patch of the same series introduced. This only adds *dusty* unused history in the patchstack that nobody needs. A *clean* and *coherent* series with discrete patches is much easier to review and will get accepted much faster.

My rule is do ONE thing at ONE patch, is it not correct?

Previous one[2/14]: Remove the vbus operation at imx glue layer. This one [3/14]: Fix a bug that vbus may be gotten delay (EPROBE_DEFER), and vbus is valid at this case.

Signature · 2 lines
Best Regards,
Peter Chen
author
#8 lore raw

PATCH v13 4/14 usb: chipidea: udc: otg_set_peripheral is useless for some chipidea users

In reply to Peter Chen

It is useless at below cases:
- If we implement both usb host and device at chipidea driver.
- If we don't need phy->otg.

---
 drivers/usb/chipidea/udc.c |    7 ++++++-
 1 files changed, 6 insertions(+), 1 deletions(-)
drivers/usb/chipidea/udc.c +6 -1
index e475fcd..116c762 100644
@@ -1805,7 +1805,12 @@ static int udc_start(struct ci_hdrc *ci)
 	if (ci->transceiver) {
 		retval = otg_set_peripheral(ci->transceiver->otg,
 						&ci->gadget);
-		if (retval)
+		/*
+		 * If we implement all USB functions using chipidea drivers,
+		 * it doesn't need to call above API, meanwhile, if we only
+		 * use gadget function, calling above API is useless.
+		 */
+		if (retval && retval != -ENOTSUPP)
 			goto put_transceiver;
 	}
 
Signature · 1 line
1.7.0.4
author
#9 lore raw

PATCH v13 5/14 usb: chipidea: otg: Add otg file used to access otgsc

In reply to Peter Chen

This file is mainly used to access otgsc currently, it may add otg related things in the future.

---
 drivers/usb/chipidea/Makefile |    2 +-
 drivers/usb/chipidea/bits.h   |   10 ++++++++
 drivers/usb/chipidea/core.c   |    3 +-
 drivers/usb/chipidea/otg.c    |   50 +++++++++++++++++++++++++++++++++++++++++
 drivers/usb/chipidea/otg.h    |   19 +++++++++++++++
 5 files changed, 82 insertions(+), 2 deletions(-)
drivers/usb/chipidea/Makefile +1 -1
index 6cf5f68..a99d980 100644
@@ -2,7 +2,7 @@ ccflags-$(CONFIG_USB_CHIPIDEA_DEBUG) := -DDEBUG
 
 obj-$(CONFIG_USB_CHIPIDEA)		+= ci_hdrc.o
 
-ci_hdrc-y				:= core.o
+ci_hdrc-y				:= core.o otg.o
 ci_hdrc-$(CONFIG_USB_CHIPIDEA_UDC)	+= udc.o
 ci_hdrc-$(CONFIG_USB_CHIPIDEA_HOST)	+= host.o
 ci_hdrc-$(CONFIG_USB_CHIPIDEA_DEBUG)	+= debug.o
drivers/usb/chipidea/bits.h +10 -0
index aefa026..dd0cf9e 100644
@@ -79,11 +79,21 @@
 #define OTGSC_ASVIS	      BIT(18)
 #define OTGSC_BSVIS	      BIT(19)
 #define OTGSC_BSEIS	      BIT(20)
+#define OTGSC_1MSIS	      BIT(21)
+#define OTGSC_DPIS	      BIT(22)
 #define OTGSC_IDIE	      BIT(24)
 #define OTGSC_AVVIE	      BIT(25)
 #define OTGSC_ASVIE	      BIT(26)
 #define OTGSC_BSVIE	      BIT(27)
 #define OTGSC_BSEIE	      BIT(28)
+#define OTGSC_1MSIE	      BIT(29)
+#define OTGSC_DPIE	      BIT(30)
+#define OTGSC_INT_EN_BITS	(OTGSC_IDIE | OTGSC_AVVIE | OTGSC_ASVIE \
+				| OTGSC_BSVIE | OTGSC_BSEIE | OTGSC_1MSIE \
+				| OTGSC_DPIE)
+#define OTGSC_INT_STATUS_BITS	(OTGSC_IDIS | OTGSC_AVVIS | OTGSC_ASVIS	\
+				| OTGSC_BSVIS | OTGSC_BSEIS | OTGSC_1MSIS \
+				| OTGSC_DPIS)
 
 /* USBMODE */
 #define USBMODE_CM            (0x03UL <<  0)
drivers/usb/chipidea/core.c +2 -1
index a5df24c..761f7e8 100644
@@ -71,6 +71,7 @@
 #include "bits.h"
 #include "host.h"
 #include "debug.h"
+#include "otg.h"
 
 /* Controller register map */
 static uintptr_t ci_regs_nolpm[] = {
@@ -508,7 +509,7 @@ static int ci_hdrc_probe(struct platform_device *pdev)
 		goto stop;
 
 	if (ci->is_otg)
-		hw_write(ci, OP_OTGSC, OTGSC_IDIE, OTGSC_IDIE);
+		ci_hdrc_otg_init(ci);
 
 	ret = dbg_create_files(ci);
 	if (!ret)
drivers/usb/chipidea/otg.c new file +50 -0

50 lines not on this page · raw message

drivers/usb/chipidea/otg.h new file +19 -0
new file mode 100644
index 0000000..f24ec37
@@ -0,0 +1,19 @@
+/*
+ * Copyright (C) 2013 Freescale Semiconductor, Inc.
+ *
+ * Author: Peter Chen
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef __DRIVERS_USB_CHIPIDEA_OTG_H
+#define __DRIVERS_USB_CHIPIDEA_OTG_H
+
+int ci_hdrc_otg_init(struct ci_hdrc *ci);
+void ci_clear_otg_interrupt(struct ci_hdrc *ci, u32 bits);
+void ci_enable_otg_interrupt(struct ci_hdrc *ci, u32 bits);
+void ci_disable_otg_interrupt(struct ci_hdrc *ci, u32 bits);
+
+#endif /* __DRIVERS_USB_CHIPIDEA_OTG_H */
Signature · 1 line
1.7.0.4
author
#10 lore raw

PATCH v13 6/14 usb: chipidea: Add role init and destory APIs

In reply to Peter Chen

- The role's init will be called at probe procedure.
- The role's destory will be called at fail patch at probe and driver's removal.
- The role's start/stop will be called when specific role has started.

---
 drivers/usb/chipidea/core.c |   10 ++++++++--
 drivers/usb/chipidea/host.c |    7 +++++++
 drivers/usb/chipidea/host.h |    6 ++++++
 drivers/usb/chipidea/udc.c  |   36 +++++++++++++++++++++++++++---------
 drivers/usb/chipidea/udc.h  |    6 ++++++
 5 files changed, 54 insertions(+), 11 deletions(-)
drivers/usb/chipidea/core.c +8 -2
index 761f7e8..93961ff 100644
@@ -399,6 +399,12 @@ void ci_hdrc_remove_device(struct platform_device *pdev)
 }
 EXPORT_SYMBOL_GPL(ci_hdrc_remove_device);
 
+static inline void ci_role_destroy(struct ci_hdrc *ci)
+{
+	ci_hdrc_gadget_destroy(ci);
+	ci_hdrc_host_destroy(ci);
+}
+
 static int ci_hdrc_probe(struct platform_device *pdev)
 {
 	struct device	*dev = &pdev->dev;
@@ -517,7 +523,7 @@ static int ci_hdrc_probe(struct platform_device *pdev)
 
 	free_irq(ci->irq, ci);
 stop:
-	ci_role_stop(ci);
+	ci_role_destroy(ci);
 rm_wq:
 	flush_workqueue(ci->wq);
 	destroy_workqueue(ci->wq);
@@ -533,7 +539,7 @@ static int ci_hdrc_remove(struct platform_device *pdev)
 	flush_workqueue(ci->wq);
 	destroy_workqueue(ci->wq);
 	free_irq(ci->irq, ci);
-	ci_role_stop(ci);
+	ci_role_destroy(ci);
 
 	return 0;
 }
drivers/usb/chipidea/host.c +7 -0
index e94e52b..382be5b 100644
@@ -105,6 +105,13 @@ static void host_stop(struct ci_hdrc *ci)
 		regulator_disable(ci->platdata->reg_vbus);
 }
 
+
+void ci_hdrc_host_destroy(struct ci_hdrc *ci)
+{
+	if (ci->role == CI_ROLE_HOST)
+		host_stop(ci);
+}
+
 int ci_hdrc_host_init(struct ci_hdrc *ci)
 {
 	struct ci_role_driver *rdrv;
drivers/usb/chipidea/host.h +6 -0
index 058875c..5707bf3 100644
@@ -4,6 +4,7 @@
 #ifdef CONFIG_USB_CHIPIDEA_HOST
 
 int ci_hdrc_host_init(struct ci_hdrc *ci);
+void ci_hdrc_host_destroy(struct ci_hdrc *ci);
 
 #else
 
@@ -12,6 +13,11 @@ static inline int ci_hdrc_host_init(struct ci_hdrc *ci)
 	return -ENXIO;
 }
 
+static inline void ci_hdrc_host_destroy(struct ci_hdrc *ci)
+{
+
+}
+
 #endif
 
 #endif /* __DRIVERS_USB_CHIPIDEA_HOST_H */
drivers/usb/chipidea/udc.c +27 -9
index 116c762..24a100d 100644
@@ -27,6 +27,7 @@
 #include "udc.h"
 #include "bits.h"
 #include "debug.h"
+#include "otg.h"
 
 /* control endpoint description */
 static const struct usb_endpoint_descriptor
@@ -1844,13 +1845,13 @@ free_qh_pool:
 }
 
 /**
- * udc_remove: parent remove must call this to remove UDC
+ * ci_hdrc_gadget_destroy: parent remove must call this to remove UDC
  *
  * No interrupts active, the IRQ has been released
  */
-static void udc_stop(struct ci_hdrc *ci)
+void ci_hdrc_gadget_destroy(struct ci_hdrc *ci)
 {
-	if (ci == NULL)
+	if (!ci->roles[CI_ROLE_GADGET])
 		return;
 
 	usb_del_gadget_udc(&ci->gadget);
@@ -1865,15 +1866,32 @@ static void udc_stop(struct ci_hdrc *ci)
 		if (ci->global_phy)
 			usb_put_phy(ci->transceiver);
 	}
-	/* my kobject is dynamic, I swear! */
-	memset(&ci->gadget, 0, sizeof(ci->gadget));
+}
+
+static int udc_id_switch_for_device(struct ci_hdrc *ci)
+{
+	if (ci->is_otg) {
+		ci_clear_otg_interrupt(ci, OTGSC_BSVIS);
+		ci_enable_otg_interrupt(ci, OTGSC_BSVIE);
+	}
+
+	return 0;
+}
+
+static void udc_id_switch_for_host(struct ci_hdrc *ci)
+{
+	if (ci->is_otg) {
+		/* host doesn't care B_SESSION_VALID event */
+		ci_clear_otg_interrupt(ci, OTGSC_BSVIS);
+		ci_disable_otg_interrupt(ci, OTGSC_BSVIE);
+	}
 }
 
 /**
  * ci_hdrc_gadget_init - initialize device related bits
  * ci: the controller
  *
- * This function enables the gadget role, if the device is "device capable".
+ * This function initializes the gadget, if the device is "device capable".
  */
 int ci_hdrc_gadget_init(struct ci_hdrc *ci)
 {
@@ -1886,11 +1904,11 @@ int ci_hdrc_gadget_init(struct ci_hdrc *ci)
 	if (!rdrv)
 		return -ENOMEM;
 
-	rdrv->start	= udc_start;
-	rdrv->stop	= udc_stop;
+	rdrv->start	= udc_id_switch_for_device;
+	rdrv->stop	= udc_id_switch_for_host;
 	rdrv->irq	= udc_irq;
 	rdrv->name	= "gadget";
 	ci->roles[CI_ROLE_GADGET] = rdrv;
 
-	return 0;
+	return udc_start(ci);
 }
drivers/usb/chipidea/udc.h +6 -0
index 455ac21..e66df00 100644
@@ -84,6 +84,7 @@ struct ci_hw_req {
 #ifdef CONFIG_USB_CHIPIDEA_UDC
 
 int ci_hdrc_gadget_init(struct ci_hdrc *ci);
+void ci_hdrc_gadget_destroy(struct ci_hdrc *ci);
 
 #else
 
@@ -92,6 +93,11 @@ static inline int ci_hdrc_gadget_init(struct ci_hdrc *ci)
 	return -ENXIO;
 }
 
+static inline void ci_hdrc_gadget_destroy(struct ci_hdrc *ci)
+{
+
+}
+
 #endif
 
 #endif /* __DRIVERS_USB_CHIPIDEA_UDC_H */
Signature · 1 line
1.7.0.4
author
#11 lore raw

PATCH v13 7/14 usb: chipidea: add flag CI_HDRC_DUAL_ROLE_NOT_OTG

In reply to Peter Chen

Since we need otgsc to know vbus's status at some chipidea controllers even it is peripheral-only mode. Besides, some SoCs (eg, AR9331 SoC) don't have otgsc register even the DCCPARAMS_DC and DCCPARAMS_HC are both 1 at CAP_DCCPARAMS.

We inroduce flag CI_HDRC_DUAL_ROLE_NOT_OTG to indicate if the controller is dual role, but not supports OTG. If this flag is not set, we follow the rule that if DCCPARAMS_DC and DCCPARAMS_HC are both 1 at CAP_DCCPARAMS, then this controller is otg capable.

---
 drivers/usb/chipidea/core.c  |   38 +++++++++++++++++++++++++++++++-------
 include/linux/usb/chipidea.h |    5 +++++
 2 files changed, 36 insertions(+), 7 deletions(-)
drivers/usb/chipidea/core.c +31 -7
index 93961ff..28983c3 100644
@@ -405,6 +405,18 @@ static inline void ci_role_destroy(struct ci_hdrc *ci)
 	ci_hdrc_host_destroy(ci);
 }
 
+static void ci_get_otg_capable(struct ci_hdrc *ci)
+{
+	if (ci->platdata->flags & CI_HDRC_DUAL_ROLE_NOT_OTG)
+		ci->is_otg = false;
+	else
+		ci->is_otg = (hw_read(ci, CAP_DCCPARAMS,
+				DCCPARAMS_DC | DCCPARAMS_HC)
+					== (DCCPARAMS_DC | DCCPARAMS_HC));
+	if (ci->is_otg)
+		dev_dbg(ci->dev, "It is OTG capable controller\n");
+}
+
 static int ci_hdrc_probe(struct platform_device *pdev)
 {
 	struct device	*dev = &pdev->dev;
@@ -461,6 +473,9 @@ static int ci_hdrc_probe(struct platform_device *pdev)
 		return -ENODEV;
 	}
 
+	/* To know if controller is OTG capable or not */
+	ci_get_otg_capable(ci);
+
 	if (!ci->platdata->phy_mode)
 		ci->platdata->phy_mode = of_usb_get_phy_mode(dev->of_node);
 
@@ -491,10 +506,22 @@ static int ci_hdrc_probe(struct platform_device *pdev)
 	}
 
 	if (ci->roles[CI_ROLE_HOST] && ci->roles[CI_ROLE_GADGET]) {
-		ci->is_otg = true;
-		/* ID pin needs 1ms debouce time, we delay 2ms for safe */
-		mdelay(2);
-		ci->role = ci_otg_role(ci);
+		if (ci->is_otg) {
+			/*
+			 * ID pin needs 1ms debouce time,
+			 * we delay 2ms for safe.
+			 */
+			mdelay(2);
+			ci->role = ci_otg_role(ci);
+			ci_hdrc_otg_init(ci);
+		} else {
+			/*
+			 * If the controller is not OTG capable, but support
+			 * role switch, the defalt role is gadget, and the
+			 * user can switch it through debugfs (proc in future?)
+			 */
+			ci->role = CI_ROLE_GADGET;
+		}
 	} else {
 		ci->role = ci->roles[CI_ROLE_HOST]
 			? CI_ROLE_HOST
@@ -514,9 +541,6 @@ static int ci_hdrc_probe(struct platform_device *pdev)
 	if (ret)
 		goto stop;
 
-	if (ci->is_otg)
-		ci_hdrc_otg_init(ci);
-
 	ret = dbg_create_files(ci);
 	if (!ret)
 		return 0;
include/linux/usb/chipidea.h +5 -0
index 118bf66..e94dc2e 100644
@@ -20,6 +20,11 @@ struct ci_hdrc_platform_data {
 #define CI_HDRC_REQUIRE_TRANSCEIVER	BIT(1)
 #define CI_HDRC_PULLUP_ON_VBUS		BIT(2)
 #define CI_HDRC_DISABLE_STREAMING	BIT(3)
+	/*
+	 * Only set it when DCCPARAMS.DC==1 and DCCPARAMS.HC==1,
+	 * but otg is not supported (no register otgsc).
+	 */
+#define CI_HDRC_DUAL_ROLE_NOT_OTG	BIT(4)
 	enum usb_dr_mode	dr_mode;
 #define CI_HDRC_CONTROLLER_RESET_EVENT		0
 #define CI_HDRC_CONTROLLER_STOPPED_EVENT	1
Signature · 1 line
1.7.0.4
author
#12 lore raw

PATCH v13 8/14 usb: chipidea: disable all interrupts and clear all interrupts status

In reply to Peter Chen

During the initialization, it needs to disable all interrupts enable bit as well as clear all interrupts status bits to avoid exceptional interrupt.

---
 drivers/usb/chipidea/core.c |   11 ++++++++++-
 1 files changed, 10 insertions(+), 1 deletions(-)
drivers/usb/chipidea/core.c +10 -1
index 28983c3..8884af6 100644
@@ -198,6 +198,12 @@ static int hw_device_init(struct ci_hdrc *ci, void __iomem *base)
 	if (ci->hw_ep_max > ENDPT_MAX)
 		return -ENODEV;
 
+	/* Disable all interrupts bits */
+	hw_write(ci, OP_USBINTR, 0xffffffff, 0);
+
+	/* Clear all interrupts status bits*/
+	hw_write(ci, OP_USBSTS, 0xffffffff, 0xffffffff);
+
 	dev_dbg(ci->dev, "ChipIdea HDRC found, lpm: %d; cap: %p op: %p\n",
 		ci->hw_bank.lpm, ci->hw_bank.cap, ci->hw_bank.op);
 
@@ -413,8 +419,11 @@ static void ci_get_otg_capable(struct ci_hdrc *ci)
 		ci->is_otg = (hw_read(ci, CAP_DCCPARAMS,
 				DCCPARAMS_DC | DCCPARAMS_HC)
 					== (DCCPARAMS_DC | DCCPARAMS_HC));
-	if (ci->is_otg)
+	if (ci->is_otg) {
 		dev_dbg(ci->dev, "It is OTG capable controller\n");
+		ci_disable_otg_interrupt(ci, OTGSC_INT_EN_BITS);
+		ci_clear_otg_interrupt(ci, OTGSC_INT_STATUS_BITS);
+	}
 }
 
 static int ci_hdrc_probe(struct platform_device *pdev)
Signature · 1 line
1.7.0.4
author
#13 lore raw

PATCH v13 9/14 usb: chipidea: move otg relate things to otg file

In reply to Peter Chen

Move otg relate things to otg file.

---
 drivers/usb/chipidea/core.c |   63 +++++++++----------------------------------
 drivers/usb/chipidea/otg.c  |   57 +++++++++++++++++++++++++++++++++++++-
 drivers/usb/chipidea/otg.h  |    2 +
 3 files changed, 70 insertions(+), 52 deletions(-)
drivers/usb/chipidea/core.c +13 -50
index 8884af6..78c4721 100644
@@ -295,40 +295,6 @@ int hw_device_reset(struct ci_hdrc *ci, u32 mode)
 	return 0;
 }
 
-/**
- * ci_otg_role - pick role based on ID pin state
- * @ci: the controller
- */
-static enum ci_role ci_otg_role(struct ci_hdrc *ci)
-{
-	u32 sts = hw_read(ci, OP_OTGSC, ~0);
-	enum ci_role role = sts & OTGSC_ID
-		? CI_ROLE_GADGET
-		: CI_ROLE_HOST;
-
-	return role;
-}
-
-/**
- * ci_role_work - perform role changing based on ID pin
- * @work: work struct
- */
-static void ci_role_work(struct work_struct *work)
-{
-	struct ci_hdrc *ci = container_of(work, struct ci_hdrc, work);
-	enum ci_role role = ci_otg_role(ci);
-
-	if (role != ci->role) {
-		dev_dbg(ci->dev, "switching from %s to %s\n",
-			ci_role(ci)->name, ci->roles[role]->name);
-
-		ci_role_stop(ci);
-		ci_role_start(ci, role);
-	}
-
-	enable_irq(ci->irq);
-}
-
 static irqreturn_t ci_irq(int irq, void *data)
 {
 	struct ci_hdrc *ci = data;
@@ -409,6 +375,8 @@ static inline void ci_role_destroy(struct ci_hdrc *ci)
 {
 	ci_hdrc_gadget_destroy(ci);
 	ci_hdrc_host_destroy(ci);
+	if (ci->is_otg)
+		ci_hdrc_otg_destory(ci);
 }
 
 static void ci_get_otg_capable(struct ci_hdrc *ci)
@@ -475,13 +443,6 @@ static int ci_hdrc_probe(struct platform_device *pdev)
 		return -ENODEV;
 	}
 
-	INIT_WORK(&ci->work, ci_role_work);
-	ci->wq = create_singlethread_workqueue("ci_otg");
-	if (!ci->wq) {
-		dev_err(dev, "can't create workqueue\n");
-		return -ENODEV;
-	}
-
 	/* To know if controller is OTG capable or not */
 	ci_get_otg_capable(ci);
 
@@ -510,8 +471,15 @@ static int ci_hdrc_probe(struct platform_device *pdev)
 
 	if (!ci->roles[CI_ROLE_HOST] && !ci->roles[CI_ROLE_GADGET]) {
 		dev_err(dev, "no supported roles\n");
-		ret = -ENODEV;
-		goto rm_wq;
+		return -ENODEV;
+	}
+
+	if (ci->is_otg) {
+		ret = ci_hdrc_otg_init(ci);
+		if (ret) {
+			dev_err(dev, "init otg fails, ret = %d\n", ret);
+			goto stop;
+		}
 	}
 
 	if (ci->roles[CI_ROLE_HOST] && ci->roles[CI_ROLE_GADGET]) {
@@ -522,7 +490,7 @@ static int ci_hdrc_probe(struct platform_device *pdev)
 			 */
 			mdelay(2);
 			ci->role = ci_otg_role(ci);
-			ci_hdrc_otg_init(ci);
+			ci_enable_otg_interrupt(ci, OTGSC_IDIE);
 		} else {
 			/*
 			 * If the controller is not OTG capable, but support
@@ -541,7 +509,7 @@ static int ci_hdrc_probe(struct platform_device *pdev)
 	if (ret) {
 		dev_err(dev, "can't start %s role\n", ci_role(ci)->name);
 		ret = -ENODEV;
-		goto rm_wq;
+		goto stop;
 	}
 
 	platform_set_drvdata(pdev, ci);
@@ -557,9 +525,6 @@ static int ci_hdrc_probe(struct platform_device *pdev)
 	free_irq(ci->irq, ci);
 stop:
 	ci_role_destroy(ci);
-rm_wq:
-	flush_workqueue(ci->wq);
-	destroy_workqueue(ci->wq);
 
 	return ret;
 }
@@ -569,8 +534,6 @@ static int ci_hdrc_remove(struct platform_device *pdev)
 	struct ci_hdrc *ci = platform_get_drvdata(pdev);
 
 	dbg_remove_files(ci);
-	flush_workqueue(ci->wq);
-	destroy_workqueue(ci->wq);
 	free_irq(ci->irq, ci);
 	ci_role_destroy(ci);
 
drivers/usb/chipidea/otg.c +55 -2

67 lines not on this page · raw message

drivers/usb/chipidea/otg.h +2 -0
index f24ec37..8913062 100644
@@ -15,5 +15,7 @@ int ci_hdrc_otg_init(struct ci_hdrc *ci);
 void ci_clear_otg_interrupt(struct ci_hdrc *ci, u32 bits);
 void ci_enable_otg_interrupt(struct ci_hdrc *ci, u32 bits);
 void ci_disable_otg_interrupt(struct ci_hdrc *ci, u32 bits);
+void ci_hdrc_otg_destory(struct ci_hdrc *ci);
+enum ci_role ci_otg_role(struct ci_hdrc *ci);
 
 #endif /* __DRIVERS_USB_CHIPIDEA_OTG_H */
Signature · 1 line
1.7.0.4
author
#14 lore raw

PATCH v13 10/14 usb: chipidea: add vbus interrupt handler

In reply to Peter Chen

We add vbus interrupt handler at ci_otg_work, it uses OTGSC_BSV(at otgsc) to know it is connect or disconnet event.
Meanwhile, we introduce two flags id_event and b_sess_valid_event to indicate it is an id interrupt or a vbus interrupt.

---
 drivers/usb/chipidea/ci.h   |    5 +++++
 drivers/usb/chipidea/core.c |   28 +++++++++++++++++++++++-----
 drivers/usb/chipidea/otg.c  |   42 +++++++++++++++++++++++++++++++++++-------
 drivers/usb/chipidea/otg.h  |    1 +
 drivers/usb/chipidea/udc.c  |    7 +++++++
 5 files changed, 71 insertions(+), 12 deletions(-)
drivers/usb/chipidea/ci.h +5 -0
index 33cb29f..3160363 100644
@@ -132,6 +132,9 @@ struct hw_bank {
  * @transceiver: pointer to USB PHY, if any
  * @hcd: pointer to usb_hcd for ehci host driver
  * @debugfs: root dentry for this controller in debugfs
+ * @id_event: indicates there is an id event, and handled at ci_otg_work
+ * @b_sess_valid_event: indicates there is a vbus event, and handled
+ * at ci_otg_work
  */
 struct ci_hdrc {
 	struct device			*dev;
@@ -168,6 +171,8 @@ struct ci_hdrc {
 	struct usb_phy			*transceiver;
 	struct usb_hcd			*hcd;
 	struct dentry			*debugfs;
+	bool				id_event;
+	bool				b_sess_valid_event;
 };
 
 static inline struct ci_role_driver *ci_role(struct ci_hdrc *ci)
drivers/usb/chipidea/core.c +23 -5
index 78c4721..0fbeb45 100644
@@ -304,16 +304,34 @@ static irqreturn_t ci_irq(int irq, void *data)
 	if (ci->is_otg)
 		otgsc = hw_read(ci, OP_OTGSC, ~0);
 
-	if (ci->role != CI_ROLE_END)
-		ret = ci_role(ci)->irq(ci);
+	/*
+	 * Handle id change interrupt, it indicates device/host function
+	 * switch.
+	 */
+	if (ci->is_otg && (otgsc & OTGSC_IDIE) && (otgsc & OTGSC_IDIS)) {
+		ci->id_event = true;
+		ci_clear_otg_interrupt(ci, OTGSC_IDIS);
+		disable_irq_nosync(ci->irq);
+		queue_work(ci->wq, &ci->work);
+		return IRQ_HANDLED;
+	}
 
-	if (ci->is_otg && (otgsc & OTGSC_IDIS)) {
-		hw_write(ci, OP_OTGSC, OTGSC_IDIS, OTGSC_IDIS);
+	/*
+	 * Handle vbus change interrupt, it indicates device connection
+	 * and disconnection events.
+	 */
+	if (ci->is_otg && (otgsc & OTGSC_BSVIE) && (otgsc & OTGSC_BSVIS)) {
+		ci->b_sess_valid_event = true;
+		ci_clear_otg_interrupt(ci, OTGSC_BSVIS);
 		disable_irq_nosync(ci->irq);
 		queue_work(ci->wq, &ci->work);
-		ret = IRQ_HANDLED;
+		return IRQ_HANDLED;
 	}
 
+	/* Handle device/host interrupt */
+	if (ci->role != CI_ROLE_END)
+		ret = ci_role(ci)->irq(ci);
+
 	return ret;
 }
 
drivers/usb/chipidea/otg.c +35 -7

65 lines not on this page · raw message

drivers/usb/chipidea/otg.h +1 -0
index 8913062..b8d5c05 100644
@@ -17,5 +17,6 @@ void ci_enable_otg_interrupt(struct ci_hdrc *ci, u32 bits);
 void ci_disable_otg_interrupt(struct ci_hdrc *ci, u32 bits);
 void ci_hdrc_otg_destory(struct ci_hdrc *ci);
 enum ci_role ci_otg_role(struct ci_hdrc *ci);
+void ci_handle_vbus_change(struct ci_hdrc *ci);
 
 #endif /* __DRIVERS_USB_CHIPIDEA_OTG_H */
drivers/usb/chipidea/udc.c +7 -0
index 24a100d..c70ce38 100644
@@ -85,8 +85,10 @@ static int hw_device_state(struct ci_hdrc *ci, u32 dma)
 		/* interrupt, error, port change, reset, sleep/suspend */
 		hw_write(ci, OP_USBINTR, ~0,
 			     USBi_UI|USBi_UEI|USBi_PCI|USBi_URI|USBi_SLI);
+		hw_write(ci, OP_USBCMD, USBCMD_RS, USBCMD_RS);
 	} else {
 		hw_write(ci, OP_USBINTR, ~0, 0);
+		hw_write(ci, OP_USBCMD, USBCMD_RS, 0);
 	}
 	return 0;
 }
@@ -1460,6 +1462,7 @@ static int ci_udc_vbus_session(struct usb_gadget *_gadget, int is_active)
 			pm_runtime_get_sync(&_gadget->dev);
 			hw_device_reset(ci, USBMODE_CM_DC);
 			hw_device_state(ci, ci->ep0out->qh.dma);
+			dev_dbg(ci->dev, "Connected to host\n");
 		} else {
 			hw_device_state(ci, 0);
 			if (ci->platdata->notify_event)
@@ -1467,6 +1470,7 @@ static int ci_udc_vbus_session(struct usb_gadget *_gadget, int is_active)
 				CI_HDRC_CONTROLLER_STOPPED_EVENT);
 			_gadget_stop_activity(&ci->gadget);
 			pm_runtime_put_sync(&_gadget->dev);
+			dev_dbg(ci->dev, "Disconnected from host\n");
 		}
 	}
 
@@ -1822,6 +1826,9 @@ static int udc_start(struct ci_hdrc *ci)
 	pm_runtime_no_callbacks(&ci->gadget.dev);
 	pm_runtime_enable(&ci->gadget.dev);
 
+	/* Update ci->vbus_active */
+	ci_handle_vbus_change(ci);
+
 	return retval;
 
 remove_trans:
Signature · 1 line
1.7.0.4
author
#15 lore raw

PATCH v13 11/14 usb: chipidea: add wait vbus lower than OTGSC_BSV before role starts

In reply to Peter Chen

When the gadget role starts, we need to make sure the vbus is lower than OTGSC_BSV, or there will be an vbus interrupt since we use B_SESSION_VALID as vbus interrupt to indicate connect and disconnect. When the host role starts, it may not be useful to wait vbus to lower than OTGSC_BSV, but it can indicate some hardware problems like the vbus is still higher than OTGSC_BSV after we disconnect to host some time later (5000 milliseconds currently), which is obvious not correct.

---
 drivers/usb/chipidea/ci.h   |    3 +++
 drivers/usb/chipidea/core.c |   32 ++++++++++++++++++++++++++++++++
 drivers/usb/chipidea/otg.c  |    4 ++++
 3 files changed, 39 insertions(+), 0 deletions(-)
drivers/usb/chipidea/ci.h +3 -0
index 3160363..1c94fc5 100644
@@ -308,4 +308,7 @@ int hw_port_test_set(struct ci_hdrc *ci, u8 mode);
 
 u8 hw_port_test_get(struct ci_hdrc *ci);
 
+int hw_wait_reg(struct ci_hdrc *ci, enum ci_hw_regs reg, u32 mask,
+				u32 value, unsigned int timeout_ms);
+
 #endif	/* __DRIVERS_USB_CHIPIDEA_CI_H */
drivers/usb/chipidea/core.c +32 -0
index 0fbeb45..6f9e04d 100644
@@ -295,6 +295,38 @@ int hw_device_reset(struct ci_hdrc *ci, u32 mode)
 	return 0;
 }
 
+/**
+ * hw_wait_reg: wait the register value
+ *
+ * Sometimes, it needs to wait register value before going on.
+ * Eg, when switch to device mode, the vbus value should be lower
+ * than OTGSC_BSV before connects to host.
+ *
+ * @ci: the controller
+ * @reg: register index
+ * @mask: mast bit
+ * @value: the bit value to wait
+ * @timeout_ms: timeout in millisecond
+ *
+ * This function returns an error code if timeout
+ */
+int hw_wait_reg(struct ci_hdrc *ci, enum ci_hw_regs reg, u32 mask,
+				u32 value, unsigned int timeout_ms)
+{
+	unsigned long elapse = jiffies + msecs_to_jiffies(timeout_ms);
+
+	while (hw_read(ci, reg, mask) != value) {
+		if (time_after(jiffies, elapse)) {
+			dev_err(ci->dev, "timeout waiting for %08x in %d\n",
+					mask, reg);
+			return -ETIMEDOUT;
+		}
+		msleep(20);
+	}
+
+	return 0;
+}
+
 static irqreturn_t ci_irq(int irq, void *data)
 {
 	struct ci_hdrc *ci = data;
drivers/usb/chipidea/otg.c +4 -0
index c74194d..d39cce8 100644
@@ -67,6 +67,7 @@ void ci_handle_vbus_change(struct ci_hdrc *ci)
 		usb_gadget_vbus_disconnect(&ci->gadget);
 }
 
+#define CI_VBUS_STABLE_TIMEOUT_MS 5000
 static void ci_handle_id_switch(struct ci_hdrc *ci)
 {
 	enum ci_role role = ci_otg_role(ci);
@@ -76,6 +77,9 @@ static void ci_handle_id_switch(struct ci_hdrc *ci)
 			ci_role(ci)->name, ci->roles[role]->name);
 
 		ci_role_stop(ci);
+		/* wait vbus lower than OTGSC_BSV */
+		hw_wait_reg(ci, OP_OTGSC, OTGSC_BSV, 0,
+				CI_VBUS_STABLE_TIMEOUT_MS);
 		ci_role_start(ci, role);
 	}
 }
Signature · 1 line
1.7.0.4
author
#16 lore raw

PATCH v13 12/14 usb: chipidea: udc: misuse flag CI_HDRC_REGS_SHARED and CI_HDRC_PULLUP_ON_VBUS

In reply to Peter Chen

CI_HDRC_REGS_SHARED stands for the controller registers is shared with other USB drivers, if all USB drivers are at chipidea/, it doesn't needed to set.
CI_HDRC_PULLUP_ON_VBUS stands for pullup dp when the vbus is on. This flag doesn't need to set if the vbus is always on for gadget since dp has always pulled up after the gadget has initialized.

So, the current code seems to misuse this two flags.
- When the gadget initializes, the controller doesn't need to run if it depends on vbus (CI_HDRC_PULLUP_ON_VBUS), it does not relate to shared register.
- When the gadget starts (load one gadget module), the controller can run if vbus is on (CI_HDRC_PULLUP_ON_VBUS), it also does not relate to shared register.

---
 drivers/usb/chipidea/udc.c |    5 ++---
 1 files changed, 2 insertions(+), 3 deletions(-)
drivers/usb/chipidea/udc.c +2 -3
index c70ce38..45abf4d 100644
@@ -1637,8 +1637,7 @@ static int ci_udc_start(struct usb_gadget *gadget,
 	pm_runtime_get_sync(&ci->gadget.dev);
 	if (ci->platdata->flags & CI_HDRC_PULLUP_ON_VBUS) {
 		if (ci->vbus_active) {
-			if (ci->platdata->flags & CI_HDRC_REGS_SHARED)
-				hw_device_reset(ci, USBMODE_CM_DC);
+			hw_device_reset(ci, USBMODE_CM_DC);
 		} else {
 			pm_runtime_put_sync(&ci->gadget.dev);
 			goto done;
@@ -1801,7 +1800,7 @@ static int udc_start(struct ci_hdrc *ci)
 		}
 	}
 
-	if (!(ci->platdata->flags & CI_HDRC_REGS_SHARED)) {
+	if (!(ci->platdata->flags & CI_HDRC_PULLUP_ON_VBUS)) {
 		retval = hw_device_reset(ci, USBMODE_CM_DC);
 		if (retval)
 			goto put_transceiver;
Signature · 1 line
1.7.0.4
author
#17 lore raw

PATCH v13 13/14 usb: chipidea: udc: .pullup is valid when vbus is on at CI_HDRC_PULLUP_ON_VBUS

In reply to Peter Chen

When the flag CI_HDRC_PULLUP_ON_VBUS is set, .pullup should only be called when the vbus is active. When the CI_HDRC_PULLUP_ON_VBUS is set, the controller only begins to run when the vbus is on, So, it is only meaningful software set pullup/pulldown after the controller begins to run.

---
 drivers/usb/chipidea/udc.c |    4 ++++
 1 files changed, 4 insertions(+), 0 deletions(-)
drivers/usb/chipidea/udc.c +4 -0
index 45abf4d..b7ead5f 100644
@@ -1514,6 +1514,10 @@ static int ci_udc_pullup(struct usb_gadget *_gadget, int is_on)
 {
 	struct ci_hdrc *ci = container_of(_gadget, struct ci_hdrc, gadget);
 
+	if ((ci->platdata->flags & CI_HDRC_PULLUP_ON_VBUS)
+			&& !ci->vbus_active)
+		return -EOPNOTSUPP;
+
 	if (is_on)
 		hw_write(ci, OP_USBCMD, USBCMD_RS, USBCMD_RS);
 	else
Signature · 1 line
1.7.0.4
author
#18 lore raw

PATCH v13 14/14 usb: chipidea: udc: fix the oops when plugs in usb cable after rmmod gadget

In reply to Peter Chen

When we rmmod gadget, the ci->driver needs to be cleared. Otherwise, we plug in usb cable again, the driver will consider gadget is there, in fact, it was removed.

Besides, consolidate the calling of ci->driver->disconnect, when we do rmmod gadget, the gadget's disconnect should be called from udc core.

Below is the oops this patch fixes.

root at freescale ~$ ci_hdrc ci_hdrc.0: Connected to host

Unable to handle kernel paging request at virtual address 7f01171c
pgd = 80004000
[7f01171c] *pgd=4fa1e811, *pte=00000000, *ppte=00000000
Internal error: Oops: 7 [#1] SMP ARM
Modules linked in: f_acm libcomposite u_serial [last unloaded: g_serial]
CPU: 0    Not tainted  (3.8.0-rc5+ #221)
PC is at _gadget_stop_activity+0xbc/0x128
LR is at ep_fifo_flush+0x68/0xa0
pc : [<803634cc>]    lr : [<80363938>]    psr: 20000193

sp : 806c7dc8 ip : 00000000 fp : 806c7de4
r10: 00000000 r9 : 80710ea4 r8 : 00000000
r7 : bf834094 r6 : bf834098 r5 : bf834010 r4 : bf8340a0 r3 : 7f011708 r2 : 01940194 r1 : a0000193 r0 : bf834014
Flags: nzCv IRQs off FIQs on Mode SVC_32 ISA ARM Segment kernel
Control: 10c53c7d Table: 4f06404a DAC: 00000017
Process swapper/0 (pid: 0, stack limit = 0x806c6238)

Stack: (0x806c7dc8 to 0x806c8000)

7dc0: bf834010 bf809950 bf834010 0000004b 806c7e44 806c7de8
7de0: 80365400 8036341c 0000ec1c 00000000 0000ec1c 00000040 fff5ede0 bf834014 7e00: 000a1220 00000000 0000002e ffffd958 806c7e3c 806c7e20 8004e870 bf834010 7e20: bf809950 0000004b 0000004b 00000000 80710ea4 00000000 806c7e5c 806c7e48 7e40: 80362888 80365154 bfb35180 bf809950 806c7e9c 806c7e60 8008111c 803627f4 7e60: 00989680 00000000 bf809900 bf809964 812df8c0 bf809900 bf809950 806c3f2c 7e80: 0000004b 00000000 412fc09a 00000000 806c7eb4 806c7ea0 80081368 800810b8 7ea0: bf809900 bf809950 806c7ecc 806c7eb8 800843c8 8008130c 0000004b 806cf748 7ec0: 806c7ee4 806c7ed0 80081088 8008432c 806c6000 806cf748 806c7f0c 806c7ee8 7ee0: 8000fa44 8008105c f400010c 806ce974 806c7f30 f4000110 806d29e8 412fc09a 7f00: 806c7f2c 806c7f10 80008584 8000f9f4 8000fbd0 60000013 ffffffff 806c7f64 7f20: 806c7f84 806c7f30 8000eac0 80008554 00000000 00000000 0000000f 8001aea0 7f40: 806c6000 80712a48 804f0040 00000000 806d29e8 412fc09a 00000000 806c7f84 7f60: 806c7f88 806c7f78 8000fbcc 8000fbd0 60000013 ffffffff 806c7fac 806c7f88 7f80: 8001015c 8000fb9c 806cf5b0 80712980 806a4528 8fffffff 1000406a 412fc09a 7fa0: 806c7fbc 806c7fb0 804e5334 800100ac 806c7ff4 806c7fc0 80668940 804e52d4 7fc0: ffffffff ffffffff 806684bc 00000000 00000000 806a4528 10c53c7d 806ce94c 7fe0: 806a4524 806d29dc 00000000 806c7ff8 10008078 806686b0 00000000 00000000

Backtrace:
[<80363410>] (_gadget_stop_activity+0x0/0x128) from [<80365400>] (udc_irq+0x2b8/0xf38)
 r7:0000004b r6:bf834010 r5:bf809950 r4:bf834010
 [<80365148>] (udc_irq+0x0/0xf38) from [<80362888>] (ci_irq+0xa0/0xf4)
[<803627e8>] (ci_irq+0x0/0xf4) from [<8008111c>] (handle_irq_event_percpu+0x70/0x254)
 r5:bf809950 r4:bfb35180
 [<800810ac>] (handle_irq_event_percpu+0x0/0x254) from [<80081368>] (handle_irq_event+0x68/0x88)
[<80081300>] (handle_irq_event+0x0/0x88) from [<800843c8>] (handle_fasteoi_irq+0xa8/0x178)
 r5:bf809950 r4:bf809900
 [<80084320>] (handle_fasteoi_irq+0x0/0x178) from [<80081088>] (generic_handle_irq+0x38/0x40)
 r5:806cf748 r4:0000004b
 [<80081050>] (generic_handle_irq+0x0/0x40) from [<8000fa44>] (handle_IRQ+0x5c/0xbc)
 r5:806cf748 r4:806c6000
 [<8000f9e8>] (handle_IRQ+0x0/0xbc) from [<80008584>] (gic_handle_irq+0x3c/0x70)
 r9:412fc09a r8:806d29e8 r7:f4000110 r6:806c7f30 r5:806ce974
 r4:f400010c
 [<80008548>] (gic_handle_irq+0x0/0x70) from [<8000eac0>] (__irq_svc+0x40/0x54)
Exception stack(0x806c7f30 to 0x806c7f78)

7f20: 00000000 00000000 0000000f 8001aea0
7f40: 806c6000 80712a48 804f0040 00000000 806d29e8 412fc09a 00000000 806c7f84 7f60: 806c7f88 806c7f78 8000fbcc 8000fbd0 60000013 ffffffff
r7:806c7f64 r6:ffffffff r5:60000013 r4:8000fbd0
[<8000fb90>] (default_idle+0x0/0x4c) from [<8001015c>] (cpu_idle+0xbc/0xf8)
[<800100a0>] (cpu_idle+0x0/0xf8) from [<804e5334>] (rest_init+0x6c/0x84)
r9:412fc09a r8:1000406a r7:8fffffff r6:806a4528 r5:80712980 r4:806cf5b0
[<804e52c8>] (rest_init+0x0/0x84) from [<80668940>] (start_kernel+0x29c/0x2ec)
[<806686a4>] (start_kernel+0x0/0x2ec) from [<10008078>] (0x10008078)

Code: e12fff33 e5953200 e3530000 0a000002 (e5933014)
---[ end trace aade28ad434062bd ]---
Kernel panic - not syncing: 0xbf8bdfa8)

df60: 00000000 00000000 0000000f 8001aea0 bf8bc000 80712a48 804f0040 00000000
df80: 806d29e8 412fc09a 00000000 bf8bdfb4 bf8bdfb8 bf8bdfa8 8000fbcc 8000fbd0
dfa0: 60000013 ffffffff
r7:bf8bdf94 r6:ffffffff r5:60000013 r4:8000fbd0
[<8000fb90>] (default_idle+0x0/0x4c) from [<8001015c>] (cpu_idle+0xbc/0xf8)
[<800100a0>] (cpu_idle+0x0/0xf8) from [<804e7930>] (secondary_start_kernel+0x120/0x148)
r9:412fc09a r8:1000406a r7:80712d20 r6:10c03c7d r5:00000002
r4:806e2008
[<804e7810>] (secondary_start_kernel+0x0/0x148) from [<104e7148>] (0x104e7148) r5:0000001f r4:4f8a806a
CPU3: stopping

 Backtrace:
 [<800132e8>] (dump_backtrace+0x0/0x114) from [<804ea684>] (dump_stack+0x20/0x24)
 r7:00000000 r6:806c3f2c r5:806cf748 r4:80712d18
 [<804ea664>] (dump_stack+0x0/0x24) from [<80014adc>] (handle_IPI+0x140/0x18c)
[<8001499c>] (handle_IPI+0x0/0x18c) from [<800085b0>] (gic_handle_irq+0x68/0x70)
 r9:412fc09a r8:806d29e8 r7:f4000110 r6:bf8bff60 r5:806ce974
 r4:f400010c
 [<80008548>] (gic_handle_irq+0x0/0x70) from [<8000eac0>] (__irq_svc+0x40/0x54)
Exception stack(0xbf8bff60 to 0xbf8bffa8)

ff60: 00000000 00000000 0000000f 8001aea0 bf8be000 80712a48 804f0040 00000000
ff80: 806d29e8 412fc09a 00000000 bf8bffb4 bf8bffb8 bf8bffa8 8000fbcc 8000fbd0
ffa0: 60000013 ffffffff
r7:bf8bff94 r6:ffffffff r5:60000013 r4:8000fbd0
[<8000fb90>] (default_idle+0x0/0x4c) from [<8001015c>] (cpu_idle+0xbc/0xf8)
[<800100a0>] (cpu_idle+0x0/0xf8) from [<804e7930>] (secondary_start_kernel+0x120/0x148)
r9:412fc09a r8:1000406a r7:80712d20 r6:10c03c7d r5:00000003
r4:806e2008
[<804e7810>] (secondary_start_kernel+0x0/0x148) from [<104e7148>] (0x104e7148) r5:0000001f r4:4f8a806a
CPU1: stopping

 Backtrace:
 [<800132e8>] (dump_backtrace+0x0/0x114) from [<804ea684>] (dump_stack+0x20/0x24)
 r7:00000000 r6:806c3f2c r5:806cf748 r4:80712d18
 [<804ea664>] (dump_stack+0x0/0x24) from [<80014adc>] (handle_IPI+0x140/0x18c)
[<8001499c>] (handle_IPI+0x0/0x18c) from [<800085b0>] (gic_handle_irq+0x68/0x70)
 r9:412fc09a r8:806d29e8 r7:f4000110 r6:bf8bbf60 r5:806ce974
 r4:f400010c
 [<80008548>] (gic_handle_irq+0x0/0x70) from [<8000eac0>] (__irq_svc+0x40/0x54)
Exception stack(0xbf8bbf60 to 0xbf8bbfa8)

bf60: 00000000 00000000 0000000f 8001aea0 bf8ba000 80712a48 804f0040 00000000
bf80: 806d29e8 412fc09a 00000000 bf8bbfb4 bf8bbfb8 bf8bbfa8 8000fbcc 8000fbd0
bfa0: 60000013 ffffffff
r7:bf8bbf94 r6:ffffffff r5:60000013 r4:8000fbd0
[<8000fb90>] (default_idle+0x0/0x4c) from [<8001015c>] (cpu_idle+0xbc/0xf8)
[<800100a0>] (cpu_idle+0x0/0xf8) from [<804e7930>] (secondary_start_kernel+0x120/0x148)
r9:412fc09a r8:1000406a r7:80712d20 r6:10c03c7d r5:00000001
r4:806e2008

---
 drivers/usb/chipidea/udc.c |   13 +++++++++----
 1 files changed, 9 insertions(+), 4 deletions(-)
drivers/usb/chipidea/udc.c +9 -4
index b7ead5f..aeabdcf 100644
@@ -686,9 +686,6 @@ static int _gadget_stop_activity(struct usb_gadget *gadget)
 	usb_ep_fifo_flush(&ci->ep0out->ep);
 	usb_ep_fifo_flush(&ci->ep0in->ep);
 
-	if (ci->driver)
-		ci->driver->disconnect(gadget);
-
 	/* make sure to disable all endpoints */
 	gadget_for_each_ep(ep, gadget) {
 		usb_ep_disable(ep);
@@ -717,6 +714,11 @@ __acquires(ci->lock)
 {
 	int retval;
 
+	if (ci->gadget.speed != USB_SPEED_UNKNOWN) {
+		if (ci->driver)
+			ci->driver->disconnect(&ci->gadget);
+	}
+
 	spin_unlock(&ci->lock);
 	retval = _gadget_stop_activity(&ci->gadget);
 	if (retval)
@@ -1464,6 +1466,8 @@ static int ci_udc_vbus_session(struct usb_gadget *_gadget, int is_active)
 			hw_device_state(ci, ci->ep0out->qh.dma);
 			dev_dbg(ci->dev, "Connected to host\n");
 		} else {
+			if (ci->driver)
+				ci->driver->disconnect(&ci->gadget);
 			hw_device_state(ci, 0);
 			if (ci->platdata->notify_event)
 				ci->platdata->notify_event(ci,
@@ -1674,13 +1678,14 @@ static int ci_udc_stop(struct usb_gadget *gadget,
 		if (ci->platdata->notify_event)
 			ci->platdata->notify_event(ci,
 			CI_HDRC_CONTROLLER_STOPPED_EVENT);
-		ci->driver = NULL;
 		spin_unlock_irqrestore(&ci->lock, flags);
 		_gadget_stop_activity(&ci->gadget);
 		spin_lock_irqsave(&ci->lock, flags);
 		pm_runtime_put(&ci->gadget.dev);
 	}
 
+	ci->driver = NULL;
+
 	spin_unlock_irqrestore(&ci->lock, flags);
 
 	return 0;
Signature · 1 line
1.7.0.4
#19 lore raw

v13 cover Add tested id switch and vbus connect detect support for Chipidea

In reply to Peter Chen

Hi Alex, any comments, now it finished 3.11-rc4, I don't want this patchset missed at 3.11.

Please tell me which one is OK, and which one needs to be refined, thanks.

Best regards,
Peter
________________________________________
From: [email protected] [linux-usb-owner at vger.kernel.org] on behalf of Peter Chen [peter.chen at freescale.com]
Sent: Friday, July 26, 2013 5:18 PM
To: alexander.shishkin at linux.intel.com
Cc: linux-usb at vger.kernel.org; linux-arm-kernel at lists.infradead.org; festevam at gmail.com; marex at denx.de; maxime.ripard at free-electrons.com; shawn.guo at linaro.org; kernel at pengutronix.de; mkl at pengutronix.de; m.grzeschik at pengutronix.de; gregkh at linuxfoundation.org; Li Frank-B20596
Subject: [PATCH v13 00/14] Add tested id switch and vbus connect detect support for Chipidea

This patchset adds tested otg id switch function and vbus connect and disconnect detection for chipidea driver. And fix kinds of bugs found at chipidea drivers after enabling id and vbus detection.

This patch are fully tested at imx6 sabresd and imx28evk platform by me. Besides, marek tested it on two STMP3780-based boards (not yet mainline) and two MX28-based boards.

My chipidea repo: https://github.com/hzpeterchen/linux-usb.git

Chagnes for v13:
- Add Tested-by: Marek Vasut <[email protected]>
- [Sascha's comments]: Add return value check for devm_regulator_get. [3/14]
- [Marc's comments]: Change timeout usage at hw_wait_reg. [11/14]
- [Alex's comments]: Using platdata flag to indicate dual role but not OTG controller. [7/14]

Changes for v12:
- Rebased greg's usb-next tree (3.10.0-rc7+)
- Split more small patches for single function and fix.

Changes for v11:
- mark ci_handle_vbus_change as static as it is only used at core.c [3/9]
- Move the vbus operation for platform code to host code, as vbus operation is common operation, and host is the only user for vbus. When it is host mode, we need to open vbus, when it is out of host mode, we need to close vbus. [6/9] [8/9]
- Delete the delayed work at core.c as it is not needed. [7/9]

Changes for v10:
- Delete [8/9] at v9, ci core's drvdata must be set for further operation. [8/8]

Changes for v9:
- Some small comments from Alex like: variable comment for otg event additional newline. [3/9]
- Import function tell show if the controller has otg capable, if the controller supports both host and device, we think it is otg capable, and can read OTGSC. [3/9]
- Merge two otg patches [v8 3/8] and [v8 4/8] to one [v9 3/9]. [3/9]
- Add inline to ci_hdrc_gadget_destroy if CONFIG_USB_CHIPIDEA_UDC is not defined, it can fix one build warning "defined but not used" [3/9]
- One comment from Felipe about changing calling gadget disconnect API at chipidea's udc driver. I move calling ci->driver->disconnect from _gadget_stop_activity to which calls _gadget_stop_activity except ci13xxx_stop, as udc core will call disconnect when do rmmod gadget. [7/9]
- Add ci core probe's return value to ci's platform_data, we do this for getting core's probe's result at platform layer, and quit it if the core's probe fails. [8/9] [9/9]

Changes for v8:
- Add ci_supports_gadget helper to know if the controller supports gadget, if the controller supports gadget, it needs to read otgsc to know the vbus value, basically, if the controller supports gadget, it will support host as well [3/8]
- At ci_hdrc_probe, it needs to add free memory at error path [3/8]
- Cosolidate ci->driver = NULL at ci13xxx_stop [8/8]

Changes for v7:
For Patch 8/8, we only need to set ci->driver to NULL when usb cable is not connected, for other changes, it will case some runtime pm unmatch and un-align with udc-core & composite driver problems.

Changes for v6:
- Add Alex comments for init/destroy function [3/8] [4/8]
- Remove memset(&ci->gadget, 0, sizeof(ci->gadget)) at destory function [4/8]
- Add Kishon's comment: Change the format of struct usb_otg otg at drivers/usb/chipidea/ci.h [1/8]
- Add comments for CI_VBUS_STABLE_TIMEOUT [3/8]
- Change the otg_set_peripheral return value check as the fully
chipidea driver users don't need it. [4/8]
- Fix one bug that the oops when re-plug in usb cable after
rmmod gadget [8/8]

Peter Chen (14):
usb: chipidea: add vbus regulator control
usb: chipidea: imx: remove vbus regulator operation
usb: chipidea: imx: add return value check for devm_regulator_get
usb: chipidea: udc: otg_set_peripheral is useless for some chipidea
users
usb: chipidea: otg: Add otg file used to access otgsc
usb: chipidea: Add role init and destory APIs
usb: chipidea: add flag CI_HDRC_DUAL_ROLE_NOT_OTG
usb: chipidea: disable all interrupts and clear all interrupts status
usb: chipidea: move otg relate things to otg file
usb: chipidea: add vbus interrupt handler
usb: chipidea: add wait vbus lower than OTGSC_BSV before role starts
usb: chipidea: udc: misuse flag CI_HDRC_REGS_SHARED and
CI_HDRC_PULLUP_ON_VBUS
usb: chipidea: udc: .pullup is valid when vbus is on at
CI_HDRC_PULLUP_ON_VBUS
usb: chipidea: udc: fix the oops when plugs in usb cable after rmmod
gadget

 drivers/usb/chipidea/Makefile      |    2 +-
 drivers/usb/chipidea/bits.h        |   10 ++
 drivers/usb/chipidea/ci.h          |    8 ++
 drivers/usb/chipidea/ci_hdrc_imx.c |   40 ++++-----
 drivers/usb/chipidea/core.c        |  161 ++++++++++++++++++++++++------------
 drivers/usb/chipidea/host.c        |   30 +++++++-
 drivers/usb/chipidea/host.h        |    6 ++
 drivers/usb/chipidea/otg.c         |  135 ++++++++++++++++++++++++++++++
 drivers/usb/chipidea/otg.h         |   22 +++++
 drivers/usb/chipidea/udc.c         |   72 ++++++++++++----
 drivers/usb/chipidea/udc.h         |    6 ++
 include/linux/usb/chipidea.h       |    6 ++
 12 files changed, 402 insertions(+), 96 deletions(-)
 create mode 100644 drivers/usb/chipidea/otg.c
 create mode 100644 drivers/usb/chipidea/otg.h

--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in the body of a message to majordomo at vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html