Skip to contentSkip to conversation

regulator: palmas: model SMPS10 as two regulators

PATCH Applied Kishon Vijay Abraham I 2 participants 2 messages Aug 12, 2013

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

PATCH v4 1/1 regulator: palmas: model SMPS10 as two regulators

SMPS10 has two outputs OUT1 and OUT2 and have one input IN1. SMPS10-OUT2 is connected to SMPS10-IN1 and can be configured either in BOOST mode or BYPASS mode. regulator_enable of SMPS10-OUT2 configures it in BOOST mode. For BYPASS mode regulator_allow_bypass() API can be used. SMPS10-OUT1 is connected to SMPS10-OUT2 and can be enabled using regulator_enable().

[ [email protected] : Simplify regulator_desc setting for SMPS10_[OUT1|OUT2]

---
Changes from v3:
rolled in Axel's fix.
rebased to Linux 3.11-rc5

Changes from v2:
Fixed the compilation error. drivers/regulator/palmas-regulator.c: In function 'palmas_regulators_probe':
drivers/regulator/palmas-regulator.c:850:8: error: 'PALMAS_REG_SMPS10' undeclared (first use in this function)
case PALMAS_REG_SMPS10:

        ^

Changes from v1:
Reversed the order of SMPS10_OUT2 and SMPS10_OUT1 since the input signal of OUT1 is OUT2

 drivers/regulator/palmas-regulator.c |   30 ++++++++++++++++++++++++------
 include/linux/mfd/palmas.h           |    9 +++++----
 2 files changed, 29 insertions(+), 10 deletions(-)
drivers/regulator/palmas-regulator.c +24 -6
index d0c8785..ab58e95 100644
@@ -97,11 +97,16 @@ static const struct regs_info palmas_regs_info[] = {
 		.ctrl_addr	= PALMAS_SMPS9_CTRL,
 	},
 	{
-		.name		= "SMPS10",
+		.name		= "SMPS10_OUT2",
 		.sname		= "smps10-in",
 		.ctrl_addr	= PALMAS_SMPS10_CTRL,
 	},
 	{
+		.name		= "SMPS10_OUT1",
+		.sname		= "smps10-out2",
+		.ctrl_addr	= PALMAS_SMPS10_CTRL,
+	},
+	{
 		.name		= "LDO1",
 		.sname		= "ldo1-in",
 		.vsel_addr	= PALMAS_LDO1_VOLTAGE,
@@ -487,6 +492,8 @@ static struct regulator_ops palmas_ops_smps10 = {
 	.set_voltage_sel	= regulator_set_voltage_sel_regmap,
 	.list_voltage		= regulator_list_voltage_linear,
 	.map_voltage		= regulator_map_voltage_linear,
+	.set_bypass		= regulator_set_bypass_regmap,
+	.get_bypass		= regulator_get_bypass_regmap,
 };
 
 static int palmas_is_enabled_ldo(struct regulator_dev *dev)
@@ -538,7 +545,8 @@ static int palmas_smps_init(struct palmas *palmas, int id,
 		return ret;
 
 	switch (id) {
-	case PALMAS_REG_SMPS10:
+	case PALMAS_REG_SMPS10_OUT1:
+	case PALMAS_REG_SMPS10_OUT2:
 		reg &= ~PALMAS_SMPS10_CTRL_MODE_SLEEP_MASK;
 		if (reg_init->mode_sleep)
 			reg |= reg_init->mode_sleep <<
@@ -681,7 +689,8 @@ static struct of_regulator_match palmas_matches[] = {
 	{ .name = "smps7", },
 	{ .name = "smps8", },
 	{ .name = "smps9", },
-	{ .name = "smps10", },
+	{ .name = "smps10_out2", },
+	{ .name = "smps10_out1", },
 	{ .name = "ldo1", },
 	{ .name = "ldo2", },
 	{ .name = "ldo3", },
@@ -838,7 +847,8 @@ static int palmas_regulators_probe(struct platform_device *pdev)
 				continue;
 			ramp_delay_support = true;
 			break;
-		case PALMAS_REG_SMPS10:
+		case PALMAS_REG_SMPS10_OUT1:
+		case PALMAS_REG_SMPS10_OUT2:
 			if (!PALMAS_PMIC_HAS(palmas, SMPS10_BOOST))
 				continue;
 		}
@@ -872,7 +882,8 @@ static int palmas_regulators_probe(struct platform_device *pdev)
 		pmic->desc[id].id = id;
 
 		switch (id) {
-		case PALMAS_REG_SMPS10:
+		case PALMAS_REG_SMPS10_OUT1:
+		case PALMAS_REG_SMPS10_OUT2:
 			pmic->desc[id].n_voltages = PALMAS_SMPS10_NUM_VOLTAGES;
 			pmic->desc[id].ops = &palmas_ops_smps10;
 			pmic->desc[id].vsel_reg =
@@ -882,7 +893,14 @@ static int palmas_regulators_probe(struct platform_device *pdev)
 			pmic->desc[id].enable_reg =
 					PALMAS_BASE_TO_REG(PALMAS_SMPS_BASE,
 							PALMAS_SMPS10_CTRL);
-			pmic->desc[id].enable_mask = SMPS10_BOOST_EN;
+			if (id == PALMAS_REG_SMPS10_OUT1)
+				pmic->desc[id].enable_mask = SMPS10_SWITCH_EN;
+			else
+				pmic->desc[id].enable_mask = SMPS10_BOOST_EN;
+			pmic->desc[id].bypass_reg =
+					PALMAS_BASE_TO_REG(PALMAS_SMPS_BASE,
+							PALMAS_SMPS10_CTRL);
+			pmic->desc[id].bypass_mask = SMPS10_BYPASS_EN;
 			pmic->desc[id].min_uV = 3750000;
 			pmic->desc[id].uV_step = 1250000;
 			break;
include/linux/mfd/palmas.h +5 -4
index 1a8dd7a..c06d78a 100644
@@ -160,7 +160,8 @@ enum palmas_regulators {
 	PALMAS_REG_SMPS7,
 	PALMAS_REG_SMPS8,
 	PALMAS_REG_SMPS9,
-	PALMAS_REG_SMPS10,
+	PALMAS_REG_SMPS10_OUT2,
+	PALMAS_REG_SMPS10_OUT1,
 	/* LDO regulators */
 	PALMAS_REG_LDO1,
 	PALMAS_REG_LDO2,
@@ -355,9 +356,9 @@ struct palmas_pmic {
 	int smps123;
 	int smps457;
 
-	int range[PALMAS_REG_SMPS10];
-	unsigned int ramp_delay[PALMAS_REG_SMPS10];
-	unsigned int current_reg_mode[PALMAS_REG_SMPS10];
+	int range[PALMAS_REG_SMPS10_OUT1];
+	unsigned int ramp_delay[PALMAS_REG_SMPS10_OUT1];
+	unsigned int current_reg_mode[PALMAS_REG_SMPS10_OUT1];
 };
 
 struct palmas_resource {
Signature · 1 line
1.7.10.4
maintainer Applied
#1 lore raw
Quoted 6 lines · Kishon Vijay Abraham I

SMPS10 has two outputs OUT1 and OUT2 and have one input IN1. SMPS10-OUT2 is connected to SMPS10-IN1 and can be configured either in BOOST mode or BYPASS mode. regulator_enable of SMPS10-OUT2 configures it in BOOST mode. For BYPASS mode regulator_allow_bypass() API can be used. SMPS10-OUT1 is connected to SMPS10-OUT2 and can be enabled using regulator_enable().

Applied, thanks.