ARM: signal: sigreturn_codes should be endian neutral to work in BE8

In case of BE8 kernel data is in BE order whereas code stays in LE order. Move sigreturn_codes to separate .S file and use proper assembler mnemonics for these code snippets. In this case compiler will take care of proper instructions byteswaps for BE8 case. Change assumes that sufficiently Thumb-capable tools are used to build kernel.

Problem was discovered during ltp testing of BE system: all rt_sig* tests failed. Tested against the same tests in both BE and LE modes.

Signed-off-by Victor Kamensky <[email protected]>

---
 arch/arm/kernel/Makefile          |  3 +-
 arch/arm/kernel/signal.c          | 24 +-------------
 arch/arm/kernel/sigreturn_codes.S | 69 +++++++++++++++++++++++++++++++++++++++
 3 files changed, 72 insertions(+), 24 deletions(-)
 create mode 100644 arch/arm/kernel/sigreturn_codes.S

arch/arm/kernel/Makefile +2 -1

index 86d10dd..0722155 100644
@@ -17,7 +17,8 @@ CFLAGS_REMOVE_return_address.o = -pg
 
 obj-y		:= elf.o entry-common.o irq.o opcodes.o \
 		   process.o ptrace.o return_address.o \
-		   setup.o signal.o stacktrace.o sys_arm.o time.o traps.o
+		   setup.o signal.o sigreturn_codes.o \
+		   stacktrace.o sys_arm.o time.o traps.o
 
 obj-$(CONFIG_ATAGS)		+= atags_parse.o
 obj-$(CONFIG_ATAGS_PROC)	+= atags_proc.o

arch/arm/kernel/signal.c +1 -23

index ab33042..64845fc 100644
@@ -21,29 +21,7 @@
 #include <asm/unistd.h>
 #include <asm/vfp.h>
 
-/*
- * For ARM syscalls, we encode the syscall number into the instruction.
- */
-#define SWI_SYS_SIGRETURN	(0xef000000|(__NR_sigreturn)|(__NR_OABI_SYSCALL_BASE))
-#define SWI_SYS_RT_SIGRETURN	(0xef000000|(__NR_rt_sigreturn)|(__NR_OABI_SYSCALL_BASE))
-
-/*
- * With EABI, the syscall number has to be loaded into r7.
- */
-#define MOV_R7_NR_SIGRETURN	(0xe3a07000 | (__NR_sigreturn - __NR_SYSCALL_BASE))
-#define MOV_R7_NR_RT_SIGRETURN	(0xe3a07000 | (__NR_rt_sigreturn - __NR_SYSCALL_BASE))
-
-/*
- * For Thumb syscalls, we pass the syscall number via r7.  We therefore
- * need two 16-bit instructions.
- */
-#define SWI_THUMB_SIGRETURN	(0xdf00 << 16 | 0x2700 | (__NR_sigreturn - __NR_SYSCALL_BASE))
-#define SWI_THUMB_RT_SIGRETURN	(0xdf00 << 16 | 0x2700 | (__NR_rt_sigreturn - __NR_SYSCALL_BASE))
-
-static const unsigned long sigreturn_codes[7] = {
-	MOV_R7_NR_SIGRETURN,    SWI_SYS_SIGRETURN,    SWI_THUMB_SIGRETURN,
-	MOV_R7_NR_RT_SIGRETURN, SWI_SYS_RT_SIGRETURN, SWI_THUMB_RT_SIGRETURN,
-};
+extern const unsigned long sigreturn_codes[7];
 
 static unsigned long signal_return_offset;
 

arch/arm/kernel/sigreturn_codes.S new file +69 -0

new file mode 100644
index 0000000..c888c43
@@ -0,0 +1,69 @@
+/*
+ * sigreturn_codes.S - code sinpets for sigreturn syscalls
+ *
+ * Created by:	Victor Kamensky, 2013-08-13
+ * Copyright:	(C) 2013  Linaro Limited
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <asm/unistd.h>
+
+/*
+ * For ARM syscalls, we encode the syscall number into the instruction.
+ * With EABI, the syscall number has to be loaded into r7. As result
+ * ARM syscall sequence snippet will have move and svc in .arm encoding
+ *
+ * For Thumb syscalls, we pass the syscall number via r7.  We therefore
+ * need two 16-bit instructions in .thumb encoding
+ *
+ * Please note sigreturn_codes code are not executed in place. Instead
+ * they just copied by kernel into appropriate places. Code inside of
+ * arch/arm/kernel/signal.c is very sensitive to layout of these code
+ * snippets.
+ */
+
+	.section .rodata
+	.global sigreturn_codes
+	.type	sigreturn_codes, #object
+
+	.arm
+
+sigreturn_codes:
+
+	/* ARM sigreturn syscall code snippet */
+	mov	r7, #(__NR_sigreturn - __NR_SYSCALL_BASE)
+	swi	#(__NR_sigreturn)|(__NR_OABI_SYSCALL_BASE)
+
+	/* Thumb sigreturn syscall code snippet */
+	.thumb
+	movs	r7, #(__NR_sigreturn - __NR_SYSCALL_BASE)
+	swi	#0
+
+	/* ARM sigreturn_rt syscall code snippet */
+	.arm
+	mov	r7, #(__NR_rt_sigreturn - __NR_SYSCALL_BASE)
+	swi	#(__NR_rt_sigreturn)|(__NR_OABI_SYSCALL_BASE)
+
+	/* Thumb sigreturn_rt syscall code snippet */
+	.thumb
+	movs	r7, #(__NR_rt_sigreturn - __NR_SYSCALL_BASE)
+	swi	#0
+
+	/*
+	 * Note on addtional space: setup_return in signal.c
+	 * algorithm uses two words copy regardless whether
+	 * it is thumb case or not, so we need additional
+	 * word after real last entry.
+	 */
+	.arm
+	.space	4
+
+	.size	sigreturn_codes, . - sigreturn_codes

Signature · 7 lines

1.8.1.4


_______________________________________________
linaro-kernel mailing list
linaro-kernel at lists.linaro.org
http://lists.linaro.org/mailman/listinfo/linaro-kernel