Skip to contentSkip to conversation

fool batman by simulating a layer3 mesh

B.A.T.M.A.N. Bastian Bittorf 4 participants 6 messages Sep 12, 2013 – Nov 27, 2013

lore
Share & tools
lore
#0 lore raw

discussed in IRC, i'am searched for a better way to load-balance a batman network. not the whole shaping/splashing should run on one (central) node, so we needed something to stick it to the node/AP which the user is connected to. than we have also the ability to show a good page when the network is b0rken.

short overview:

NODE-1 (master/gateway)
ipv4: 192.168.1.1/16
dhcp: 192.168.1.x / gateway: 192.168.0.1
gateway: e.g. pppoe

NODE-2
ipv4: 192.168.2.1/16
dhcp: 192.168.2.x / gateway: 192.168.0.1
gateway: 192.168.1.1

NODE-3
ipv4: 192.168.3.1/16
dhcp: 192.168.3.x / gateway: 192.168.0.1
gateway: 192.168.1.1

the trick is, that every node offers DHCP which
does not interfere with other nodes AND offers a
gateway which is always the same: 192.168.0.1

if a user roams he simply moves on layer 1/2 and its further working ok. important: the MAC of the gateway should not change otherwise it's not working for some seconds till the ARP times out. this can be circumvented via kmod-macvlan:

ip link add link br-mybridge gateway0 address '02:00:c0:ca:c0:1a' type macvlan ip address add 192.168.0.1/16 dev gateway0
ip link set dev gateway0 up

then the IP 192.168.0.1 is always reachable with the same MAC. thats it. we can use the "normal" iptables/tc stuff like in olsrd-networks...

giving out such dhcp-leases needs a fix to /etc/init.d/dhcp which is available soon on OpenWrt mailinglist.

bye, bastian

PS:
thanks for the discussion and help, escpecially to T_X, ordex and marec

#1 lore raw
Quoted 6 lines · Bastian Bittorf

discussed in IRC, i'am searched for a better way to load-balance a batman network. not the whole shaping/splashing should run on one (central) node, so we needed something to stick it to the node/AP which the user is connected to. than we have also the ability to show a good page when the network is b0rken.

I'd like to remember that you could also do the same by using iptables and the netfilter hook in the bridge code (look for netfilter_bridge). It would allow you to apply shaping/firewalling rules directly onto a bridge, without transforming each and every AP in a Layer 3 Gateway.

I think this would also fit a Layer2 mesh network better.

Cheers,

Signature · 4 lines
Antonio Quartulli

..each of us alone is worth nothing..
Ernesto "Che" Guevara
#2 lore raw
In reply to Bastian Bittorf
Quoted 5 lines · Bastian Bittorf

discussed in IRC, i'am searched for a better way to load-balance a batman network. not the whole shaping/splashing should run on one (central) node, so we needed something to stick it to the node/AP which the user is connected to. than we have also the ability to show a good page when the network is b0rken.

How do you handle the splash status of a user under roaming? Does a splash screen reoccur if the gateway is switched (NODE-2 -> NODE-3)? Because this switch will happen on a minutely basis if a user sits between two equally strong gateways.

Regards,
Jan

#3 lore raw
Quoted 4 lines · Jan Huwald

How do you handle the splash status of a user under roaming? Does a splash screen reoccur if the gateway is switched (NODE-2 -> NODE-3)? Because this switch will happen on a minutely basis if a user sits between two equally strong gateways.

Splashing is only done for clients which have a lease from this node. All other traffic gets just true (picopeer alike). After some minutes the information that "IPx/MAC must be shaped like..." is applied in the hole network. If the client only has a lease but is not "unsplashed" this information is also spread netwide.

A little bit ugly, but works and we have no memory or load problems anymore on the gateway. (~1000 clients)

bye, bastian

#4 lore raw

Hi Bastian,

Did you have a chance to try the iptables + netfilter_bridge hook (I believe via the iptables physdev module?) Antonio suggested yet?

It sounds like a good idea to me and since no one seems to have tried it with batman-adv yet I'm curious whether it works well in practice.

Whether you could enhance the user experience in an open, batman-adv based community mesh network by having an IP instead of connection based sharing of available bandwidth.

Cheers, Linus

Quoted 16 lines · Bastian Bittorf
Quoted 4 lines · Jan Huwald

How do you handle the splash status of a user under roaming? Does a splash screen reoccur if the gateway is switched (NODE-2 -> NODE-3)? Because this switch will happen on a minutely basis if a user sits between two equally strong gateways.

Splashing is only done for clients which have a lease from this node. All other traffic gets just true (picopeer alike). After some minutes the information that "IPx/MAC must be shaped like..." is applied in the hole network. If the client only has a lease but is not "unsplashed" this information is also spread netwide.

A little bit ugly, but works and we have no memory or load problems anymore on the gateway. (~1000 clients)

bye, bastian

#5 lore raw
Quoted 3 lines · Linus Lüssing

Did you have a chance to try the iptables + netfilter_bridge hook (I believe via the iptables physdev module?) Antonio suggested yet?

not yet - still working with macvlan (+ebtables for not confusing the daemon about a client which es everywhere at the same time)

Quoted 3 lines

It sounds like a good idea to me and since no one seems to have tried it with batman-adv yet I'm curious whether it works well in practice.

will have time for testing during end of december...

Quoted 3 lines

Whether you could enhance the user experience in an open, batman-adv based community mesh network by having an IP instead of connection based sharing of available bandwidth.

++

bye, bastian