Skip to contentSkip to conversation

staging/iio/adc: change the MXS touchscreen driver implementation

RFC New Juergen Beisert 4 participants 28 messages Sep 11, 2013 – Sep 19, 2013

Subsystems (5)
lore
Share & tools
lore
#0 lore raw

The following series replaces the current busy loop touchscreen implementation for i.MX28/i.MX23 SoCs by a fully interrupt driven implementation.

Since i.MX23 and i.Mx28 silicon differs, the existing implementation can be used for the i.MX28 SoC only.

So, the first two patches of this series move the i.MX28 specific definitions out of the way. The third patch simplifies the register access to make it easier to add the i.MX23 support. Then the i.MX23 specific definitions are added, also the code to distinguish both SoCs at run-time.
Up to here the existing touchscreen driver will now run on an i.MX23 Soc as well.

When the i.MX23 SoC is running from battery it seems not to be a good idea to run a busy loop to detect touches and their location. The fourth patch adds a fully interrupt driven implementation which makes use of the built-in delay and multiple sample features of the touchscreen controller. This will reduce the interrupt load to a minimum.

The last patch in this series just removes the existing busy loop implementation.

Still some restrictions/questions:

- the touchscreen part is yet tested on i.MX23 SoC only
- touchscreen parametrisation ability is provided (with fixed values for now) but should be done via device tree. Some recommendations how to define the bindings would be helpful
- has someone a good idea how to implement a reliable pressure measurement if the resistances of the touchscree's plates are unknown?

Changes since v3:

- split adding register access functions and i.MX23 support into two patches

Changes since v2:

- useless debug output removed

Changes since v1:

- adding register access functions to make the existing code more readable
- adding some functions to distinguish the SoCs at run-time to avoid if-else contructs whenever differences in the register layout between i.MX23 and i.MX28 must be handled

Comments are welcome.

Juergen

#1 lore raw

PATCH 1/6 Staging/iio/adc/touchscreen/MXS: distinguish i.MX23's and i.MX28's LRADC

The LRADC units in i.MX23 and i.MX28 differ and we need to distinguish both SoC variants in order to make the touchscreen work on i.MX23

CC linux-arm-kernel at lists.infradead.org
CC devel at driverdev.osuosl.org
CC Marek Vasut <[email protected]>
CC Fabio Estevam <[email protected]>
CC Jonathan Cameron <[email protected]>
---
 drivers/staging/iio/adc/mxs-lradc.c | 3 +++
 1 file changed, 3 insertions(+)
drivers/staging/iio/adc/mxs-lradc.c +3 -0
index a08c173..dffca90 100644
@@ -174,6 +174,8 @@ struct mxs_lradc {
 
 	struct input_dev	*ts_input;
 	struct work_struct	ts_work;
+
+	enum mxs_lradc_id	soc;
 };
 
 #define	LRADC_CTRL0				0x00
@@ -920,6 +922,7 @@ static int mxs_lradc_probe(struct platform_device *pdev)
 	}
 
 	lradc = iio_priv(iio);
+	lradc->soc = (enum mxs_lradc_id)of_id->data;
 
 	/* Grab the memory area */
 	iores = platform_get_resource(pdev, IORESOURCE_MEM, 0);
Signature · 1 line
1.8.4.rc3
#2 lore raw

PATCH 2/6 Staging/iio/adc/touchscreen/MXS: separate i.MX28 specific register bits

In reply to Juergen Beisert

In order to support i.MX23 and i.MX28 within one driver we need to separate the register definitions which differ in both SoC variants.

CC linux-arm-kernel at lists.infradead.org
CC devel at driverdev.osuosl.org
CC Marek Vasut <[email protected]>
CC Fabio Estevam <[email protected]>
CC Jonathan Cameron <[email protected]>
---
 drivers/staging/iio/adc/mxs-lradc.c | 61 ++++++++++++++++++++-----------------
 1 file changed, 33 insertions(+), 28 deletions(-)
drivers/staging/iio/adc/mxs-lradc.c +33 -28
index dffca90..5535fed 100644
@@ -179,24 +179,29 @@ struct mxs_lradc {
 };
 
 #define	LRADC_CTRL0				0x00
-#define	LRADC_CTRL0_TOUCH_DETECT_ENABLE		(1 << 23)
-#define	LRADC_CTRL0_TOUCH_SCREEN_TYPE		(1 << 22)
-#define	LRADC_CTRL0_YNNSW	/* YM */	(1 << 21)
-#define	LRADC_CTRL0_YPNSW	/* YP */	(1 << 20)
-#define	LRADC_CTRL0_YPPSW	/* YP */	(1 << 19)
-#define	LRADC_CTRL0_XNNSW	/* XM */	(1 << 18)
-#define	LRADC_CTRL0_XNPSW	/* XM */	(1 << 17)
-#define	LRADC_CTRL0_XPPSW	/* XP */	(1 << 16)
-#define	LRADC_CTRL0_PLATE_MASK			(0x3f << 16)
+# define LRADC_CTRL0_MX28_TOUCH_DETECT_ENABLE	(1 << 23)
+# define LRADC_CTRL0_MX28_TOUCH_SCREEN_TYPE	(1 << 22)
+# define LRADC_CTRL0_MX28_YNNSW	/* YM */	(1 << 21)
+# define LRADC_CTRL0_MX28_YPNSW	/* YP */	(1 << 20)
+# define LRADC_CTRL0_MX28_YPPSW	/* YP */	(1 << 19)
+# define LRADC_CTRL0_MX28_XNNSW	/* XM */	(1 << 18)
+# define LRADC_CTRL0_MX28_XNPSW	/* XM */	(1 << 17)
+# define LRADC_CTRL0_MX28_XPPSW	/* XP */	(1 << 16)
+
+# define LRADC_CTRL0_MX28_PLATE_MASK \
+		(LRADC_CTRL0_MX28_TOUCH_DETECT_ENABLE | \
+		LRADC_CTRL0_MX28_YNNSW | LRADC_CTRL0_MX28_YPNSW | \
+		LRADC_CTRL0_MX28_YPPSW | LRADC_CTRL0_MX28_XNNSW | \
+		LRADC_CTRL0_MX28_XNPSW | LRADC_CTRL0_MX28_XPPSW)
 
 #define	LRADC_CTRL1				0x10
 #define	LRADC_CTRL1_TOUCH_DETECT_IRQ_EN		(1 << 24)
 #define	LRADC_CTRL1_LRADC_IRQ_EN(n)		(1 << ((n) + 16))
-#define	LRADC_CTRL1_LRADC_IRQ_EN_MASK		(0x1fff << 16)
+#define	LRADC_CTRL1_MX28_LRADC_IRQ_EN_MASK	(0x1fff << 16)
 #define	LRADC_CTRL1_LRADC_IRQ_EN_OFFSET		16
 #define	LRADC_CTRL1_TOUCH_DETECT_IRQ		(1 << 8)
 #define	LRADC_CTRL1_LRADC_IRQ(n)		(1 << (n))
-#define	LRADC_CTRL1_LRADC_IRQ_MASK		0x1fff
+#define	LRADC_CTRL1_MX28_LRADC_IRQ_MASK		0x1fff
 #define	LRADC_CTRL1_LRADC_IRQ_OFFSET		0
 
 #define	LRADC_CTRL2				0x20
@@ -264,7 +269,7 @@ static int mxs_lradc_read_raw(struct iio_dev *iio_dev,
 	 * Virtual channel 0 is always used here as the others are always not
 	 * used if doing raw sampling.
 	 */
-	writel(LRADC_CTRL1_LRADC_IRQ_EN_MASK,
+	writel(LRADC_CTRL1_MX28_LRADC_IRQ_EN_MASK,
 		lradc->base + LRADC_CTRL1 + STMP_OFFSET_REG_CLR);
 	writel(0xff, lradc->base + LRADC_CTRL0 + STMP_OFFSET_REG_CLR);
 
@@ -319,9 +324,9 @@ static int mxs_lradc_ts_touched(struct mxs_lradc *lradc)
 	uint32_t reg;
 
 	/* Enable touch detection. */
-	writel(LRADC_CTRL0_PLATE_MASK,
+	writel(LRADC_CTRL0_MX28_PLATE_MASK,
 		lradc->base + LRADC_CTRL0 + STMP_OFFSET_REG_CLR);
-	writel(LRADC_CTRL0_TOUCH_DETECT_ENABLE,
+	writel(LRADC_CTRL0_MX28_TOUCH_DETECT_ENABLE,
 		lradc->base + LRADC_CTRL0 + STMP_OFFSET_REG_SET);
 
 	msleep(LRADC_TS_SAMPLE_DELAY_MS);
@@ -367,21 +372,21 @@ static int32_t mxs_lradc_ts_sample(struct mxs_lradc *lradc,
 	 */
 	switch (plate) {
 	case LRADC_SAMPLE_X:
-		ctrl0 = LRADC_CTRL0_XPPSW | LRADC_CTRL0_XNNSW;
+		ctrl0 = LRADC_CTRL0_MX28_XPPSW | LRADC_CTRL0_MX28_XNNSW;
 		chan = 3;
 		break;
 	case LRADC_SAMPLE_Y:
-		ctrl0 = LRADC_CTRL0_YPPSW | LRADC_CTRL0_YNNSW;
+		ctrl0 = LRADC_CTRL0_MX28_YPPSW | LRADC_CTRL0_MX28_YNNSW;
 		chan = 4;
 		break;
 	case LRADC_SAMPLE_PRESSURE:
-		ctrl0 = LRADC_CTRL0_YPPSW | LRADC_CTRL0_XNNSW;
+		ctrl0 = LRADC_CTRL0_MX28_YPPSW | LRADC_CTRL0_MX28_XNNSW;
 		chan = 5;
 		break;
 	}
 
 	if (change) {
-		writel(LRADC_CTRL0_PLATE_MASK,
+		writel(LRADC_CTRL0_MX28_PLATE_MASK,
 			lradc->base + LRADC_CTRL0 + STMP_OFFSET_REG_CLR);
 		writel(ctrl0, lradc->base + LRADC_CTRL0 + STMP_OFFSET_REG_SET);
 
@@ -442,7 +447,7 @@ static void mxs_lradc_ts_work(struct work_struct *ts_work)
 
 	while (mxs_lradc_ts_touched(lradc)) {
 		/* Disable touch detector so we can sample the touchscreen. */
-		writel(LRADC_CTRL0_TOUCH_DETECT_ENABLE,
+		writel(LRADC_CTRL0_MX28_TOUCH_DETECT_ENABLE,
 			lradc->base + LRADC_CTRL0 + STMP_OFFSET_REG_CLR);
 
 		if (likely(valid)) {
@@ -491,7 +496,7 @@ static int mxs_lradc_ts_open(struct input_dev *dev)
 	lradc->stop_touchscreen = false;
 
 	/* Enable the touch-detect circuitry. */
-	writel(LRADC_CTRL0_TOUCH_DETECT_ENABLE,
+	writel(LRADC_CTRL0_MX28_TOUCH_DETECT_ENABLE,
 		lradc->base + LRADC_CTRL0 + STMP_OFFSET_REG_SET);
 
 	/* Enable the touch-detect IRQ. */
@@ -517,7 +522,7 @@ static void mxs_lradc_ts_close(struct input_dev *dev)
 		lradc->base + LRADC_CTRL1 + STMP_OFFSET_REG_CLR);
 
 	/* Power-down touchscreen touch-detect circuitry. */
-	writel(LRADC_CTRL0_TOUCH_DETECT_ENABLE,
+	writel(LRADC_CTRL0_MX28_TOUCH_DETECT_ENABLE,
 		lradc->base + LRADC_CTRL0 + STMP_OFFSET_REG_CLR);
 }
 
@@ -581,7 +586,7 @@ static irqreturn_t mxs_lradc_handle_irq(int irq, void *data)
 		LRADC_CTRL1_TOUCH_DETECT_IRQ_EN |
 		LRADC_CTRL1_TOUCH_DETECT_IRQ;
 
-	if (!(reg & LRADC_CTRL1_LRADC_IRQ_MASK))
+	if (!(reg & LRADC_CTRL1_MX28_LRADC_IRQ_MASK))
 		return IRQ_NONE;
 
 	/*
@@ -601,7 +606,7 @@ static irqreturn_t mxs_lradc_handle_irq(int irq, void *data)
 	else if (reg & LRADC_CTRL1_LRADC_IRQ(0))
 		complete(&lradc->completion);
 
-	writel(reg & LRADC_CTRL1_LRADC_IRQ_MASK,
+	writel(reg & LRADC_CTRL1_MX28_LRADC_IRQ_MASK,
 		lradc->base + LRADC_CTRL1 + STMP_OFFSET_REG_CLR);
 
 	return IRQ_HANDLED;
@@ -722,7 +727,7 @@ static int mxs_lradc_buffer_preenable(struct iio_dev *iio)
 	if (ret < 0)
 		goto err_buf;
 
-	writel(LRADC_CTRL1_LRADC_IRQ_EN_MASK,
+	writel(LRADC_CTRL1_MX28_LRADC_IRQ_EN_MASK,
 		lradc->base + LRADC_CTRL1 + STMP_OFFSET_REG_CLR);
 	writel(0xff, lradc->base + LRADC_CTRL0 + STMP_OFFSET_REG_CLR);
 
@@ -763,7 +768,7 @@ static int mxs_lradc_buffer_postdisable(struct iio_dev *iio)
 		lradc->base + LRADC_DELAY(0) + STMP_OFFSET_REG_CLR);
 
 	writel(0xff, lradc->base + LRADC_CTRL0 + STMP_OFFSET_REG_CLR);
-	writel(LRADC_CTRL1_LRADC_IRQ_EN_MASK,
+	writel(LRADC_CTRL1_MX28_LRADC_IRQ_EN_MASK,
 		lradc->base + LRADC_CTRL1 + STMP_OFFSET_REG_CLR);
 
 	kfree(lradc->buffer);
@@ -867,11 +872,11 @@ static int mxs_lradc_hw_init(struct mxs_lradc *lradc)
 	writel(0, lradc->base + LRADC_DELAY(3));
 
 	/* Configure the touchscreen type */
-	writel(LRADC_CTRL0_TOUCH_SCREEN_TYPE,
+	writel(LRADC_CTRL0_MX28_TOUCH_SCREEN_TYPE,
 		lradc->base + LRADC_CTRL0 + STMP_OFFSET_REG_CLR);
 
 	if (lradc->use_touchscreen == MXS_LRADC_TOUCHSCREEN_5WIRE) {
-		writel(LRADC_CTRL0_TOUCH_SCREEN_TYPE,
+		writel(LRADC_CTRL0_MX28_TOUCH_SCREEN_TYPE,
 			lradc->base + LRADC_CTRL0 + STMP_OFFSET_REG_SET);
 	}
 
@@ -885,7 +890,7 @@ static void mxs_lradc_hw_stop(struct mxs_lradc *lradc)
 {
 	int i;
 
-	writel(LRADC_CTRL1_LRADC_IRQ_EN_MASK,
+	writel(LRADC_CTRL1_MX28_LRADC_IRQ_EN_MASK,
 		lradc->base + LRADC_CTRL1 + STMP_OFFSET_REG_CLR);
 
 	for (i = 0; i < LRADC_MAX_DELAY_CHANS; i++)
Signature · 1 line
1.8.4.rc3
maintainer
#3 lore raw

PATCH 2/6 Staging/iio/adc/touchscreen/MXS: separate i.MX28 specific register bits

Quoted 9 lines · Juergen Beisert

In order to support i.MX23 and i.MX28 within one driver we need to separate the register definitions which differ in both SoC variants.

I'd personally have gone for LRADC_MX28_CTRL0_* but I'm not that fussed. I am looking for an Acked-by from Marek for this series though.

Quoted 183 lines
---
 drivers/staging/iio/adc/mxs-lradc.c | 61 ++++++++++++++++++++-----------------
 1 file changed, 33 insertions(+), 28 deletions(-)
drivers/staging/iio/adc/mxs-lradc.c +33 -28
index dffca90..5535fed 100644
@@ -179,24 +179,29 @@ struct mxs_lradc {
 };
 
 #define	LRADC_CTRL0				0x00
-#define	LRADC_CTRL0_TOUCH_DETECT_ENABLE		(1 << 23)
-#define	LRADC_CTRL0_TOUCH_SCREEN_TYPE		(1 << 22)
-#define	LRADC_CTRL0_YNNSW	/* YM */	(1 << 21)
-#define	LRADC_CTRL0_YPNSW	/* YP */	(1 << 20)
-#define	LRADC_CTRL0_YPPSW	/* YP */	(1 << 19)
-#define	LRADC_CTRL0_XNNSW	/* XM */	(1 << 18)
-#define	LRADC_CTRL0_XNPSW	/* XM */	(1 << 17)
-#define	LRADC_CTRL0_XPPSW	/* XP */	(1 << 16)
-#define	LRADC_CTRL0_PLATE_MASK			(0x3f << 16)
+# define LRADC_CTRL0_MX28_TOUCH_DETECT_ENABLE	(1 << 23)
+# define LRADC_CTRL0_MX28_TOUCH_SCREEN_TYPE	(1 << 22)
+# define LRADC_CTRL0_MX28_YNNSW	/* YM */	(1 << 21)
+# define LRADC_CTRL0_MX28_YPNSW	/* YP */	(1 << 20)
+# define LRADC_CTRL0_MX28_YPPSW	/* YP */	(1 << 19)
+# define LRADC_CTRL0_MX28_XNNSW	/* XM */	(1 << 18)
+# define LRADC_CTRL0_MX28_XNPSW	/* XM */	(1 << 17)
+# define LRADC_CTRL0_MX28_XPPSW	/* XP */	(1 << 16)
+
+# define LRADC_CTRL0_MX28_PLATE_MASK \
+		(LRADC_CTRL0_MX28_TOUCH_DETECT_ENABLE | \
+		LRADC_CTRL0_MX28_YNNSW | LRADC_CTRL0_MX28_YPNSW | \
+		LRADC_CTRL0_MX28_YPPSW | LRADC_CTRL0_MX28_XNNSW | \
+		LRADC_CTRL0_MX28_XNPSW | LRADC_CTRL0_MX28_XPPSW)
 
 #define	LRADC_CTRL1				0x10
 #define	LRADC_CTRL1_TOUCH_DETECT_IRQ_EN		(1 << 24)
 #define	LRADC_CTRL1_LRADC_IRQ_EN(n)		(1 << ((n) + 16))
-#define	LRADC_CTRL1_LRADC_IRQ_EN_MASK		(0x1fff << 16)
+#define	LRADC_CTRL1_MX28_LRADC_IRQ_EN_MASK	(0x1fff << 16)
 #define	LRADC_CTRL1_LRADC_IRQ_EN_OFFSET		16
 #define	LRADC_CTRL1_TOUCH_DETECT_IRQ		(1 << 8)
 #define	LRADC_CTRL1_LRADC_IRQ(n)		(1 << (n))
-#define	LRADC_CTRL1_LRADC_IRQ_MASK		0x1fff
+#define	LRADC_CTRL1_MX28_LRADC_IRQ_MASK		0x1fff
 #define	LRADC_CTRL1_LRADC_IRQ_OFFSET		0
 
 #define	LRADC_CTRL2				0x20
@@ -264,7 +269,7 @@ static int mxs_lradc_read_raw(struct iio_dev *iio_dev,
 	 * Virtual channel 0 is always used here as the others are always not
 	 * used if doing raw sampling.
 	 */
-	writel(LRADC_CTRL1_LRADC_IRQ_EN_MASK,
+	writel(LRADC_CTRL1_MX28_LRADC_IRQ_EN_MASK,
 		lradc->base + LRADC_CTRL1 + STMP_OFFSET_REG_CLR);
 	writel(0xff, lradc->base + LRADC_CTRL0 + STMP_OFFSET_REG_CLR);
 
@@ -319,9 +324,9 @@ static int mxs_lradc_ts_touched(struct mxs_lradc *lradc)
 	uint32_t reg;
 
 	/* Enable touch detection. */
-	writel(LRADC_CTRL0_PLATE_MASK,
+	writel(LRADC_CTRL0_MX28_PLATE_MASK,
 		lradc->base + LRADC_CTRL0 + STMP_OFFSET_REG_CLR);
-	writel(LRADC_CTRL0_TOUCH_DETECT_ENABLE,
+	writel(LRADC_CTRL0_MX28_TOUCH_DETECT_ENABLE,
 		lradc->base + LRADC_CTRL0 + STMP_OFFSET_REG_SET);
 
 	msleep(LRADC_TS_SAMPLE_DELAY_MS);
@@ -367,21 +372,21 @@ static int32_t mxs_lradc_ts_sample(struct mxs_lradc *lradc,
 	 */
 	switch (plate) {
 	case LRADC_SAMPLE_X:
-		ctrl0 = LRADC_CTRL0_XPPSW | LRADC_CTRL0_XNNSW;
+		ctrl0 = LRADC_CTRL0_MX28_XPPSW | LRADC_CTRL0_MX28_XNNSW;
 		chan = 3;
 		break;
 	case LRADC_SAMPLE_Y:
-		ctrl0 = LRADC_CTRL0_YPPSW | LRADC_CTRL0_YNNSW;
+		ctrl0 = LRADC_CTRL0_MX28_YPPSW | LRADC_CTRL0_MX28_YNNSW;
 		chan = 4;
 		break;
 	case LRADC_SAMPLE_PRESSURE:
-		ctrl0 = LRADC_CTRL0_YPPSW | LRADC_CTRL0_XNNSW;
+		ctrl0 = LRADC_CTRL0_MX28_YPPSW | LRADC_CTRL0_MX28_XNNSW;
 		chan = 5;
 		break;
 	}
 
 	if (change) {
-		writel(LRADC_CTRL0_PLATE_MASK,
+		writel(LRADC_CTRL0_MX28_PLATE_MASK,
 			lradc->base + LRADC_CTRL0 + STMP_OFFSET_REG_CLR);
 		writel(ctrl0, lradc->base + LRADC_CTRL0 + STMP_OFFSET_REG_SET);
 
@@ -442,7 +447,7 @@ static void mxs_lradc_ts_work(struct work_struct *ts_work)
 
 	while (mxs_lradc_ts_touched(lradc)) {
 		/* Disable touch detector so we can sample the touchscreen. */
-		writel(LRADC_CTRL0_TOUCH_DETECT_ENABLE,
+		writel(LRADC_CTRL0_MX28_TOUCH_DETECT_ENABLE,
 			lradc->base + LRADC_CTRL0 + STMP_OFFSET_REG_CLR);
 
 		if (likely(valid)) {
@@ -491,7 +496,7 @@ static int mxs_lradc_ts_open(struct input_dev *dev)
 	lradc->stop_touchscreen = false;
 
 	/* Enable the touch-detect circuitry. */
-	writel(LRADC_CTRL0_TOUCH_DETECT_ENABLE,
+	writel(LRADC_CTRL0_MX28_TOUCH_DETECT_ENABLE,
 		lradc->base + LRADC_CTRL0 + STMP_OFFSET_REG_SET);
 
 	/* Enable the touch-detect IRQ. */
@@ -517,7 +522,7 @@ static void mxs_lradc_ts_close(struct input_dev *dev)
 		lradc->base + LRADC_CTRL1 + STMP_OFFSET_REG_CLR);
 
 	/* Power-down touchscreen touch-detect circuitry. */
-	writel(LRADC_CTRL0_TOUCH_DETECT_ENABLE,
+	writel(LRADC_CTRL0_MX28_TOUCH_DETECT_ENABLE,
 		lradc->base + LRADC_CTRL0 + STMP_OFFSET_REG_CLR);
 }
 
@@ -581,7 +586,7 @@ static irqreturn_t mxs_lradc_handle_irq(int irq, void *data)
 		LRADC_CTRL1_TOUCH_DETECT_IRQ_EN |
 		LRADC_CTRL1_TOUCH_DETECT_IRQ;
 
-	if (!(reg & LRADC_CTRL1_LRADC_IRQ_MASK))
+	if (!(reg & LRADC_CTRL1_MX28_LRADC_IRQ_MASK))
 		return IRQ_NONE;
 
 	/*
@@ -601,7 +606,7 @@ static irqreturn_t mxs_lradc_handle_irq(int irq, void *data)
 	else if (reg & LRADC_CTRL1_LRADC_IRQ(0))
 		complete(&lradc->completion);
 
-	writel(reg & LRADC_CTRL1_LRADC_IRQ_MASK,
+	writel(reg & LRADC_CTRL1_MX28_LRADC_IRQ_MASK,
 		lradc->base + LRADC_CTRL1 + STMP_OFFSET_REG_CLR);
 
 	return IRQ_HANDLED;
@@ -722,7 +727,7 @@ static int mxs_lradc_buffer_preenable(struct iio_dev *iio)
 	if (ret < 0)
 		goto err_buf;
 
-	writel(LRADC_CTRL1_LRADC_IRQ_EN_MASK,
+	writel(LRADC_CTRL1_MX28_LRADC_IRQ_EN_MASK,
 		lradc->base + LRADC_CTRL1 + STMP_OFFSET_REG_CLR);
 	writel(0xff, lradc->base + LRADC_CTRL0 + STMP_OFFSET_REG_CLR);
 
@@ -763,7 +768,7 @@ static int mxs_lradc_buffer_postdisable(struct iio_dev *iio)
 		lradc->base + LRADC_DELAY(0) + STMP_OFFSET_REG_CLR);
 
 	writel(0xff, lradc->base + LRADC_CTRL0 + STMP_OFFSET_REG_CLR);
-	writel(LRADC_CTRL1_LRADC_IRQ_EN_MASK,
+	writel(LRADC_CTRL1_MX28_LRADC_IRQ_EN_MASK,
 		lradc->base + LRADC_CTRL1 + STMP_OFFSET_REG_CLR);
 
 	kfree(lradc->buffer);
@@ -867,11 +872,11 @@ static int mxs_lradc_hw_init(struct mxs_lradc *lradc)
 	writel(0, lradc->base + LRADC_DELAY(3));
 
 	/* Configure the touchscreen type */
-	writel(LRADC_CTRL0_TOUCH_SCREEN_TYPE,
+	writel(LRADC_CTRL0_MX28_TOUCH_SCREEN_TYPE,
 		lradc->base + LRADC_CTRL0 + STMP_OFFSET_REG_CLR);
 
 	if (lradc->use_touchscreen == MXS_LRADC_TOUCHSCREEN_5WIRE) {
-		writel(LRADC_CTRL0_TOUCH_SCREEN_TYPE,
+		writel(LRADC_CTRL0_MX28_TOUCH_SCREEN_TYPE,
 			lradc->base + LRADC_CTRL0 + STMP_OFFSET_REG_SET);
 	}
 
@@ -885,7 +890,7 @@ static void mxs_lradc_hw_stop(struct mxs_lradc *lradc)
 {
 	int i;
 
-	writel(LRADC_CTRL1_LRADC_IRQ_EN_MASK,
+	writel(LRADC_CTRL1_MX28_LRADC_IRQ_EN_MASK,
 		lradc->base + LRADC_CTRL1 + STMP_OFFSET_REG_CLR);
 
 	for (i = 0; i < LRADC_MAX_DELAY_CHANS; i++)
#4 lore raw

PATCH 3/6 Staging/iio/adc/touchscreen/MXS: simplify register access

In reply to Juergen Beisert

Replace the individual register access by a few shared access function to make the code easier to read and in order to add the i.MX23 SoC in the next step.

CC linux-arm-kernel at lists.infradead.org
CC devel at driverdev.osuosl.org
CC Marek Vasut <[email protected]>
CC Fabio Estevam <[email protected]>
CC Jonathan Cameron <[email protected]>
---
 drivers/staging/iio/adc/mxs-lradc.c | 204 +++++++++++++++++++++---------------
 1 file changed, 120 insertions(+), 84 deletions(-)
drivers/staging/iio/adc/mxs-lradc.c +120 -84
index 5535fed..4317fee 100644
@@ -235,6 +235,56 @@ struct mxs_lradc {
 #define LRADC_RESOLUTION			12
 #define LRADC_SINGLE_SAMPLE_MASK		((1 << LRADC_RESOLUTION) - 1)
 
+static void mxs_lradc_reg_set(struct mxs_lradc *lradc, u32 val, u32 reg)
+{
+	writel(val, lradc->base + reg + STMP_OFFSET_REG_SET);
+}
+
+static void mxs_lradc_reg_clear(struct mxs_lradc *lradc, u32 val, u32 reg)
+{
+	writel(val, lradc->base + reg + STMP_OFFSET_REG_CLR);
+}
+
+static void mxs_lradc_reg(struct mxs_lradc *lradc, u32 val, u32 reg)
+{
+	writel(val, lradc->base + reg);
+}
+
+static u32 mxs_lradc_plate_mask(struct mxs_lradc *lradc)
+{
+	return LRADC_CTRL0_MX28_PLATE_MASK;
+}
+
+static u32 mxs_lradc_irq_en_mask(struct mxs_lradc *lradc)
+{
+	return LRADC_CTRL1_MX28_LRADC_IRQ_EN_MASK;
+}
+
+static u32 mxs_lradc_irq_mask(struct mxs_lradc *lradc)
+{
+	return LRADC_CTRL1_MX28_LRADC_IRQ_MASK;
+}
+
+static u32 mxs_lradc_touch_detect_bit(struct mxs_lradc *lradc)
+{
+	return LRADC_CTRL0_MX28_TOUCH_DETECT_ENABLE;
+}
+
+static u32 mxs_lradc_drive_x_plate(struct mxs_lradc *lradc)
+{
+	return LRADC_CTRL0_MX28_XPPSW | LRADC_CTRL0_MX28_XNNSW;
+}
+
+static u32 mxs_lradc_drive_y_plate(struct mxs_lradc *lradc)
+{
+	return LRADC_CTRL0_MX28_YPPSW | LRADC_CTRL0_MX28_YNNSW;
+}
+
+static u32 mxs_lradc_drive_pressure(struct mxs_lradc *lradc)
+{
+	return LRADC_CTRL0_MX28_YPPSW | LRADC_CTRL0_MX28_XNNSW;
+}
+
 /*
  * Raw I/O operations
  */
@@ -269,21 +319,19 @@ static int mxs_lradc_read_raw(struct iio_dev *iio_dev,
 	 * Virtual channel 0 is always used here as the others are always not
 	 * used if doing raw sampling.
 	 */
-	writel(LRADC_CTRL1_MX28_LRADC_IRQ_EN_MASK,
-		lradc->base + LRADC_CTRL1 + STMP_OFFSET_REG_CLR);
-	writel(0xff, lradc->base + LRADC_CTRL0 + STMP_OFFSET_REG_CLR);
+	mxs_lradc_reg_clear(lradc, LRADC_CTRL1_MX28_LRADC_IRQ_EN_MASK,
+			LRADC_CTRL1);
+	mxs_lradc_reg_clear(lradc, 0xff, LRADC_CTRL0);
 
 	/* Clean the slot's previous content, then set new one. */
-	writel(LRADC_CTRL4_LRADCSELECT_MASK(0),
-		lradc->base + LRADC_CTRL4 + STMP_OFFSET_REG_CLR);
-	writel(chan->channel, lradc->base + LRADC_CTRL4 + STMP_OFFSET_REG_SET);
+	mxs_lradc_reg_clear(lradc, LRADC_CTRL4_LRADCSELECT_MASK(0), LRADC_CTRL4);
+	mxs_lradc_reg_set(lradc, chan->channel, LRADC_CTRL4);
 
-	writel(0, lradc->base + LRADC_CH(0));
+	mxs_lradc_reg(lradc, 0, LRADC_CH(0));
 
 	/* Enable the IRQ and start sampling the channel. */
-	writel(LRADC_CTRL1_LRADC_IRQ_EN(0),
-		lradc->base + LRADC_CTRL1 + STMP_OFFSET_REG_SET);
-	writel(1 << 0, lradc->base + LRADC_CTRL0 + STMP_OFFSET_REG_SET);
+	mxs_lradc_reg_set(lradc, LRADC_CTRL1_LRADC_IRQ_EN(0), LRADC_CTRL1);
+	mxs_lradc_reg_set(lradc, 1 << 0, LRADC_CTRL0);
 
 	/* Wait for completion on the channel, 1 second max. */
 	ret = wait_for_completion_killable_timeout(&lradc->completion, HZ);
@@ -297,8 +345,7 @@ static int mxs_lradc_read_raw(struct iio_dev *iio_dev,
 	ret = IIO_VAL_INT;
 
 err:
-	writel(LRADC_CTRL1_LRADC_IRQ_EN(0),
-		lradc->base + LRADC_CTRL1 + STMP_OFFSET_REG_CLR);
+	mxs_lradc_reg_clear(lradc, LRADC_CTRL1_LRADC_IRQ_EN(0), LRADC_CTRL1);
 
 	mutex_unlock(&lradc->lock);
 
@@ -324,10 +371,9 @@ static int mxs_lradc_ts_touched(struct mxs_lradc *lradc)
 	uint32_t reg;
 
 	/* Enable touch detection. */
-	writel(LRADC_CTRL0_MX28_PLATE_MASK,
-		lradc->base + LRADC_CTRL0 + STMP_OFFSET_REG_CLR);
-	writel(LRADC_CTRL0_MX28_TOUCH_DETECT_ENABLE,
-		lradc->base + LRADC_CTRL0 + STMP_OFFSET_REG_SET);
+	mxs_lradc_reg_clear(lradc, mxs_lradc_plate_mask(lradc), LRADC_CTRL0);
+	mxs_lradc_reg_set(lradc, mxs_lradc_touch_detect_bit(lradc),
+								LRADC_CTRL0);
 
 	msleep(LRADC_TS_SAMPLE_DELAY_MS);
 
@@ -372,32 +418,33 @@ static int32_t mxs_lradc_ts_sample(struct mxs_lradc *lradc,
 	 */
 	switch (plate) {
 	case LRADC_SAMPLE_X:
-		ctrl0 = LRADC_CTRL0_MX28_XPPSW | LRADC_CTRL0_MX28_XNNSW;
+		ctrl0 = mxs_lradc_drive_x_plate(lradc);
 		chan = 3;
 		break;
 	case LRADC_SAMPLE_Y:
-		ctrl0 = LRADC_CTRL0_MX28_YPPSW | LRADC_CTRL0_MX28_YNNSW;
+		ctrl0 = mxs_lradc_drive_y_plate(lradc);
 		chan = 4;
 		break;
 	case LRADC_SAMPLE_PRESSURE:
-		ctrl0 = LRADC_CTRL0_MX28_YPPSW | LRADC_CTRL0_MX28_XNNSW;
+		ctrl0 = mxs_lradc_drive_pressure(lradc);
 		chan = 5;
 		break;
 	}
 
 	if (change) {
-		writel(LRADC_CTRL0_MX28_PLATE_MASK,
-			lradc->base + LRADC_CTRL0 + STMP_OFFSET_REG_CLR);
-		writel(ctrl0, lradc->base + LRADC_CTRL0 + STMP_OFFSET_REG_SET);
-
-		writel(LRADC_CTRL4_LRADCSELECT_MASK(slot),
-			lradc->base + LRADC_CTRL4 + STMP_OFFSET_REG_CLR);
-		writel(chan << LRADC_CTRL4_LRADCSELECT_OFFSET(slot),
-			lradc->base + LRADC_CTRL4 + STMP_OFFSET_REG_SET);
+		mxs_lradc_reg_clear(lradc, mxs_lradc_plate_mask(lradc),
+						LRADC_CTRL0);
+		mxs_lradc_reg_set(lradc, ctrl0, LRADC_CTRL0);
+
+		mxs_lradc_reg_clear(lradc, LRADC_CTRL4_LRADCSELECT_MASK(slot),
+						LRADC_CTRL4);
+		mxs_lradc_reg_set(lradc,
+				chan << LRADC_CTRL4_LRADCSELECT_OFFSET(slot),
+				LRADC_CTRL4);
 	}
 
-	writel(0xffffffff, lradc->base + LRADC_CH(slot) + STMP_OFFSET_REG_CLR);
-	writel(1 << slot, lradc->base + LRADC_CTRL0 + STMP_OFFSET_REG_SET);
+	mxs_lradc_reg_clear(lradc, 0xffffffff, LRADC_CH(slot));
+	mxs_lradc_reg_set(lradc, 1 << slot, LRADC_CTRL0);
 
 	delay = jiffies + msecs_to_jiffies(LRADC_TS_SAMPLE_DELAY_MS);
 	do {
@@ -407,8 +454,7 @@ static int32_t mxs_lradc_ts_sample(struct mxs_lradc *lradc,
 			break;
 	} while (time_before(jiff, delay));
 
-	writel(LRADC_CTRL1_LRADC_IRQ(slot),
-		lradc->base + LRADC_CTRL1 + STMP_OFFSET_REG_CLR);
+	mxs_lradc_reg_clear(lradc, LRADC_CTRL1_LRADC_IRQ(slot), LRADC_CTRL1);
 
 	if (time_after_eq(jiff, delay))
 		return -ETIMEDOUT;
@@ -447,8 +493,8 @@ static void mxs_lradc_ts_work(struct work_struct *ts_work)
 
 	while (mxs_lradc_ts_touched(lradc)) {
 		/* Disable touch detector so we can sample the touchscreen. */
-		writel(LRADC_CTRL0_MX28_TOUCH_DETECT_ENABLE,
-			lradc->base + LRADC_CTRL0 + STMP_OFFSET_REG_CLR);
+		mxs_lradc_reg_clear(lradc, mxs_lradc_touch_detect_bit(lradc),
+						LRADC_CTRL0);
 
 		if (likely(valid)) {
 			input_report_abs(lradc->ts_input, ABS_X, val_x);
@@ -482,10 +528,8 @@ static void mxs_lradc_ts_work(struct work_struct *ts_work)
 		return;
 
 	/* Restart the touchscreen interrupts. */
-	writel(LRADC_CTRL1_TOUCH_DETECT_IRQ,
-		lradc->base + LRADC_CTRL1 + STMP_OFFSET_REG_CLR);
-	writel(LRADC_CTRL1_TOUCH_DETECT_IRQ_EN,
-		lradc->base + LRADC_CTRL1 + STMP_OFFSET_REG_SET);
+	mxs_lradc_reg_clear(lradc, LRADC_CTRL1_TOUCH_DETECT_IRQ, LRADC_CTRL1);
+	mxs_lradc_reg_set(lradc, LRADC_CTRL1_TOUCH_DETECT_IRQ_EN, LRADC_CTRL1);
 }
 
 static int mxs_lradc_ts_open(struct input_dev *dev)
@@ -496,12 +540,11 @@ static int mxs_lradc_ts_open(struct input_dev *dev)
 	lradc->stop_touchscreen = false;
 
 	/* Enable the touch-detect circuitry. */
-	writel(LRADC_CTRL0_MX28_TOUCH_DETECT_ENABLE,
-		lradc->base + LRADC_CTRL0 + STMP_OFFSET_REG_SET);
+	mxs_lradc_reg_set(lradc, mxs_lradc_touch_detect_bit(lradc),
+						LRADC_CTRL0);
 
 	/* Enable the touch-detect IRQ. */
-	writel(LRADC_CTRL1_TOUCH_DETECT_IRQ_EN,
-		lradc->base + LRADC_CTRL1 + STMP_OFFSET_REG_SET);
+	mxs_lradc_reg_set(lradc, LRADC_CTRL1_TOUCH_DETECT_IRQ_EN, LRADC_CTRL1);
 
 	return 0;
 }
@@ -518,12 +561,11 @@ static void mxs_lradc_ts_close(struct input_dev *dev)
 	cancel_work_sync(&lradc->ts_work);
 
 	/* Disable touchscreen touch-detect IRQ. */
-	writel(LRADC_CTRL1_TOUCH_DETECT_IRQ_EN,
-		lradc->base + LRADC_CTRL1 + STMP_OFFSET_REG_CLR);
+	mxs_lradc_reg_clear(lradc, LRADC_CTRL1_TOUCH_DETECT_IRQ_EN,
+						LRADC_CTRL1);
 
 	/* Power-down touchscreen touch-detect circuitry. */
-	writel(LRADC_CTRL0_MX28_TOUCH_DETECT_ENABLE,
-		lradc->base + LRADC_CTRL0 + STMP_OFFSET_REG_CLR);
+	mxs_lradc_reg_clear(lradc, mxs_lradc_touch_detect_bit(lradc), LRADC_CTRL0);
 }
 
 static int mxs_lradc_ts_register(struct mxs_lradc *lradc)
@@ -586,7 +628,7 @@ static irqreturn_t mxs_lradc_handle_irq(int irq, void *data)
 		LRADC_CTRL1_TOUCH_DETECT_IRQ_EN |
 		LRADC_CTRL1_TOUCH_DETECT_IRQ;
 
-	if (!(reg & LRADC_CTRL1_MX28_LRADC_IRQ_MASK))
+	if (!(reg & mxs_lradc_irq_mask(lradc)))
 		return IRQ_NONE;
 
 	/*
@@ -595,8 +637,7 @@ static irqreturn_t mxs_lradc_handle_irq(int irq, void *data)
 	 * it ASAP
 	 */
 	if (reg & LRADC_CTRL1_TOUCH_DETECT_IRQ) {
-		writel(ts_irq_mask,
-			lradc->base + LRADC_CTRL1 + STMP_OFFSET_REG_CLR);
+		mxs_lradc_reg_clear(lradc, ts_irq_mask, LRADC_CTRL1);
 		if (!lradc->stop_touchscreen)
 			schedule_work(&lradc->ts_work);
 	}
@@ -606,8 +647,7 @@ static irqreturn_t mxs_lradc_handle_irq(int irq, void *data)
 	else if (reg & LRADC_CTRL1_LRADC_IRQ(0))
 		complete(&lradc->completion);
 
-	writel(reg & LRADC_CTRL1_MX28_LRADC_IRQ_MASK,
-		lradc->base + LRADC_CTRL1 + STMP_OFFSET_REG_CLR);
+	mxs_lradc_reg_clear(lradc, reg & mxs_lradc_irq_mask(lradc), LRADC_CTRL1);
 
 	return IRQ_HANDLED;
 }
@@ -626,7 +666,7 @@ static irqreturn_t mxs_lradc_trigger_handler(int irq, void *p)
 
 	for_each_set_bit(i, iio->active_scan_mask, LRADC_MAX_TOTAL_CHANS) {
 		lradc->buffer[j] = readl(lradc->base + LRADC_CH(j));
-		writel(chan_value, lradc->base + LRADC_CH(j));
+		mxs_lradc_reg(lradc, chan_value, LRADC_CH(j));
 		lradc->buffer[j] &= LRADC_CH_VALUE_MASK;
 		lradc->buffer[j] /= LRADC_DELAY_TIMER_LOOP;
 		j++;
@@ -651,7 +691,7 @@ static int mxs_lradc_configure_trigger(struct iio_trigger *trig, bool state)
 	struct mxs_lradc *lradc = iio_priv(iio);
 	const uint32_t st = state ? STMP_OFFSET_REG_SET : STMP_OFFSET_REG_CLR;
 
-	writel(LRADC_DELAY_KICK, lradc->base + LRADC_DELAY(0) + st);
+	mxs_lradc_reg(lradc, LRADC_DELAY_KICK, LRADC_DELAY(0) + st);
 
 	return 0;
 }
@@ -727,29 +767,26 @@ static int mxs_lradc_buffer_preenable(struct iio_dev *iio)
 	if (ret < 0)
 		goto err_buf;
 
-	writel(LRADC_CTRL1_MX28_LRADC_IRQ_EN_MASK,
-		lradc->base + LRADC_CTRL1 + STMP_OFFSET_REG_CLR);
-	writel(0xff, lradc->base + LRADC_CTRL0 + STMP_OFFSET_REG_CLR);
+	mxs_lradc_reg_clear(lradc, LRADC_CTRL1_MX28_LRADC_IRQ_EN_MASK,
+							LRADC_CTRL1);
+	mxs_lradc_reg_clear(lradc, 0xff, LRADC_CTRL0);
 
 	for_each_set_bit(chan, iio->active_scan_mask, LRADC_MAX_TOTAL_CHANS) {
 		ctrl4_set |= chan << LRADC_CTRL4_LRADCSELECT_OFFSET(ofs);
 		ctrl4_clr |= LRADC_CTRL4_LRADCSELECT_MASK(ofs);
 		ctrl1_irq |= LRADC_CTRL1_LRADC_IRQ_EN(ofs);
-		writel(chan_value, lradc->base + LRADC_CH(ofs));
+		mxs_lradc_reg(lradc, chan_value, LRADC_CH(ofs));
 		bitmap_set(&enable, ofs, 1);
 		ofs++;
 	}
 
-	writel(LRADC_DELAY_TRIGGER_LRADCS_MASK | LRADC_DELAY_KICK,
-		lradc->base + LRADC_DELAY(0) + STMP_OFFSET_REG_CLR);
-
-	writel(ctrl4_clr, lradc->base + LRADC_CTRL4 + STMP_OFFSET_REG_CLR);
-	writel(ctrl4_set, lradc->base + LRADC_CTRL4 + STMP_OFFSET_REG_SET);
-
-	writel(ctrl1_irq, lradc->base + LRADC_CTRL1 + STMP_OFFSET_REG_SET);
-
-	writel(enable << LRADC_DELAY_TRIGGER_LRADCS_OFFSET,
-		lradc->base + LRADC_DELAY(0) + STMP_OFFSET_REG_SET);
+	mxs_lradc_reg_clear(lradc, LRADC_DELAY_TRIGGER_LRADCS_MASK |
+					LRADC_DELAY_KICK, LRADC_DELAY(0));
+	mxs_lradc_reg_clear(lradc, ctrl4_clr, LRADC_CTRL4);
+	mxs_lradc_reg_set(lradc, ctrl4_set, LRADC_CTRL4);
+	mxs_lradc_reg_set(lradc, ctrl1_irq, LRADC_CTRL1);
+	mxs_lradc_reg_set(lradc, enable << LRADC_DELAY_TRIGGER_LRADCS_OFFSET,
+					LRADC_DELAY(0));
 
 	return 0;
 
@@ -764,12 +801,12 @@ static int mxs_lradc_buffer_postdisable(struct iio_dev *iio)
 {
 	struct mxs_lradc *lradc = iio_priv(iio);
 
-	writel(LRADC_DELAY_TRIGGER_LRADCS_MASK | LRADC_DELAY_KICK,
-		lradc->base + LRADC_DELAY(0) + STMP_OFFSET_REG_CLR);
+	mxs_lradc_reg_clear(lradc, LRADC_DELAY_TRIGGER_LRADCS_MASK |
+					LRADC_DELAY_KICK, LRADC_DELAY(0));
 
-	writel(0xff, lradc->base + LRADC_CTRL0 + STMP_OFFSET_REG_CLR);
-	writel(LRADC_CTRL1_MX28_LRADC_IRQ_EN_MASK,
-		lradc->base + LRADC_CTRL1 + STMP_OFFSET_REG_CLR);
+	mxs_lradc_reg_clear(lradc, 0xff, LRADC_CTRL0);
+	mxs_lradc_reg_clear(lradc, LRADC_CTRL1_MX28_LRADC_IRQ_EN_MASK,
+					LRADC_CTRL1);
 
 	kfree(lradc->buffer);
 	mutex_unlock(&lradc->lock);
@@ -864,24 +901,24 @@ static int mxs_lradc_hw_init(struct mxs_lradc *lradc)
 		return ret;
 
 	/* Configure DELAY CHANNEL 0 for generic ADC sampling. */
-	writel(adc_cfg, lradc->base + LRADC_DELAY(0));
+	mxs_lradc_reg(lradc, adc_cfg, LRADC_DELAY(0));
 
 	/* Disable remaining DELAY CHANNELs */
-	writel(0, lradc->base + LRADC_DELAY(1));
-	writel(0, lradc->base + LRADC_DELAY(2));
-	writel(0, lradc->base + LRADC_DELAY(3));
+	mxs_lradc_reg(lradc, 0, LRADC_DELAY(1));
+	mxs_lradc_reg(lradc, 0, LRADC_DELAY(2));
+	mxs_lradc_reg(lradc, 0, LRADC_DELAY(3));
 
 	/* Configure the touchscreen type */
-	writel(LRADC_CTRL0_MX28_TOUCH_SCREEN_TYPE,
-		lradc->base + LRADC_CTRL0 + STMP_OFFSET_REG_CLR);
+	mxs_lradc_reg_clear(lradc, LRADC_CTRL0_MX28_TOUCH_SCREEN_TYPE,
+							LRADC_CTRL0);
 
-	if (lradc->use_touchscreen == MXS_LRADC_TOUCHSCREEN_5WIRE) {
-		writel(LRADC_CTRL0_MX28_TOUCH_SCREEN_TYPE,
-			lradc->base + LRADC_CTRL0 + STMP_OFFSET_REG_SET);
+	if (lradc->use_touchscreen == MXS_LRADC_TOUCHSCREEN_5WIRE)
+		mxs_lradc_reg_set(lradc, LRADC_CTRL0_MX28_TOUCH_SCREEN_TYPE,
+				LRADC_CTRL0);
 	}
 
 	/* Start internal temperature sensing. */
-	writel(0, lradc->base + LRADC_CTRL2);
+	mxs_lradc_reg(lradc, 0, LRADC_CTRL2);
 
 	return 0;
 }
@@ -890,11 +927,10 @@ static void mxs_lradc_hw_stop(struct mxs_lradc *lradc)
 {
 	int i;
 
-	writel(LRADC_CTRL1_MX28_LRADC_IRQ_EN_MASK,
-		lradc->base + LRADC_CTRL1 + STMP_OFFSET_REG_CLR);
+	mxs_lradc_reg_clear(lradc, mxs_lradc_irq_en_mask(lradc), LRADC_CTRL1);
 
 	for (i = 0; i < LRADC_MAX_DELAY_CHANS; i++)
-		writel(0, lradc->base + LRADC_DELAY(i));
+		mxs_lradc_reg(lradc, 0, LRADC_DELAY(i));
 }
 
 static const struct of_device_id mxs_lradc_dt_ids[] = {
Signature · 1 line
1.8.4.rc3
maintainer
#5 lore raw

PATCH 3/6 Staging/iio/adc/touchscreen/MXS: simplify register access

Quoted 9 lines · Juergen Beisert

Replace the individual register access by a few shared access function to make the code easier to read and in order to add the i.MX23 SoC in the next step.

One little suggestion inline but I'm basically happy with this.

Quoted 12 lines
---
 drivers/staging/iio/adc/mxs-lradc.c | 204 +++++++++++++++++++++---------------
 1 file changed, 120 insertions(+), 84 deletions(-)
drivers/staging/iio/adc/mxs-lradc.c +0 -0
index 5535fed..4317fee 100644
@@ -235,6 +235,56 @@ struct mxs_lradc {
 #define LRADC_RESOLUTION			12
 #define LRADC_SINGLE_SAMPLE_MASK		((1 << LRADC_RESOLUTION) - 1)
 

drivers/staging/iio/adc/mxs-lradc.c struct mxs_lradc { · line 247

Quoted 10 lines
drivers/staging/iio/adc/mxs-lradc.c +10 -0
+static void mxs_lradc_reg_set(struct mxs_lradc *lradc, u32 val, u32 reg)
+{
+	writel(val, lradc->base + reg + STMP_OFFSET_REG_SET);
+}
+
+static void mxs_lradc_reg_clear(struct mxs_lradc *lradc, u32 val, u32 reg)
+{
+	writel(val, lradc->base + reg + STMP_OFFSET_REG_CLR);
+}
+

mxs_lradc_reg_write might be clearer?

Quoted 4 lines
drivers/staging/iio/adc/mxs-lradc.c +4 -0
+static void mxs_lradc_reg(struct mxs_lradc *lradc, u32 val, u32 reg)
+{
+	writel(val, lradc->base + reg);
+}
#6 lore raw

PATCH 3/6 Staging/iio/adc/touchscreen/MXS: simplify register access

Hi Jonathan,

Quoted 13 lines · On Sunday 15 September 2013 12:35:29 Jonathan Cameron wrote:

[...]

drivers/staging/iio/adc/mxs-lradc.c struct mxs_lradc { · line 247

Quoted 10 lines
drivers/staging/iio/adc/mxs-lradc.c +10 -0
+static void mxs_lradc_reg_set(struct mxs_lradc *lradc, u32 val, u32 reg)
+{
+	writel(val, lradc->base + reg + STMP_OFFSET_REG_SET);
+}
+
+static void mxs_lradc_reg_clear(struct mxs_lradc *lradc, u32 val, u32 reg)
+{ 
+	writel(val, lradc->base + reg + STMP_OFFSET_REG_CLR);
+}
+

mxs_lradc_reg_write might be clearer?

I would prefer the shorter name. Due to long macro names and long function names the lines in the code below needs more and more line breaks which is IMHO less helpfull to read the code.

Regards,
Juergen

Signature · 2 lines
Pengutronix e.K. ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?| Juergen Beisert ? ? ? ? ? ? |
Linux Solutions for Science and Industry ? ? ?| http://www.pengutronix.de/  |
maintainer
#7 lore raw

PATCH 3/6 Staging/iio/adc/touchscreen/MXS: simplify register access

Quoted 17 lines · Jürgen Beisert

Hi Jonathan,

Quoted 13 lines · On Sunday 15 September 2013 12:35:29 Jonathan Cameron wrote:

[...]

drivers/staging/iio/adc/mxs-lradc.c struct mxs_lradc { · line 247

Quoted 10 lines
drivers/staging/iio/adc/mxs-lradc.c +10 -0
+static void mxs_lradc_reg_set(struct mxs_lradc *lradc, u32 val, u32 reg)
+{
+	writel(val, lradc->base + reg + STMP_OFFSET_REG_SET);
+}
+
+static void mxs_lradc_reg_clear(struct mxs_lradc *lradc, u32 val, u32 reg)
+{ 
+	writel(val, lradc->base + reg + STMP_OFFSET_REG_CLR);
+}
+

mxs_lradc_reg_write might be clearer?

Quoted 3 lines

I would prefer the shorter name. Due to long macro names and long function names the lines in the code below needs more and more line breaks which is IMHO less helpfull to read the code.

Hmm. It's not entirely obvious what else this might be doing, but it is also not obvious from the name that it is writing to the register...

I remain unconvinced by the short name!

#8 lore raw

PATCH 3/6 Staging/iio/adc/touchscreen/MXS: simplify register access

In reply to Juergen Beisert

Dear Juergen Beisert,

Quoted 27 lines

Replace the individual register access by a few shared access function to make the code easier to read and in order to add the i.MX23 SoC in the next step.

CC linux-arm-kernel at lists.infradead.org
CC devel at driverdev.osuosl.org
CC Marek Vasut <[email protected]>
CC Fabio Estevam <[email protected]>
CC Jonathan Cameron <[email protected]>
---
 drivers/staging/iio/adc/mxs-lradc.c | 204

+++++++++++++++++++++--------------- 1 file changed, 120 insertions(+), 84 deletions(-)

(quoted diff) +0 -0

b/drivers/staging/iio/adc/mxs-lradc.c index 5535fed..4317fee 100644

drivers/staging/iio/adc/mxs-lradc.c +4 -0
@@ -235,6 +235,56 @@ struct mxs_lradc {
 #define LRADC_RESOLUTION			12
 #define LRADC_SINGLE_SAMPLE_MASK		((1 << LRADC_RESOLUTION) - 1)
 
+static void mxs_lradc_reg_set(struct mxs_lradc *lradc, u32 val, u32 reg)
+{
+	writel(val, lradc->base + reg + STMP_OFFSET_REG_SET);
+}

drivers/staging/iio/adc/mxs-lradc.c struct mxs_lradc { · line 251

Quoted 10 lines
drivers/staging/iio/adc/mxs-lradc.c +10 -0
+
+static void mxs_lradc_reg_clear(struct mxs_lradc *lradc, u32 val, u32 reg)
+{
+	writel(val, lradc->base + reg + STMP_OFFSET_REG_CLR);
+}
+
+static void mxs_lradc_reg(struct mxs_lradc *lradc, u32 val, u32 reg)
+{
+	writel(val, lradc->base + reg);
+}

Idea for later patch: Should we not move these functions to a MXS-specific header _later_ on so other drivers can leverage them too ?

[...]

Best regards,
Marek Vasut

#9 lore raw

PATCH 4/6 Staging/iio/adc/touchscreen/MXS: add i.MX23 support to the LRADC touchscreen driver

In reply to Juergen Beisert

Distinguish i.MX23 and i.MX28 at runtime and do the same for both SoC at least for the 4 wire touchscreen.

Note: support for the remaining LRADC channels is not tested on an i.MX23 yet.

CC linux-arm-kernel at lists.infradead.org
CC devel at driverdev.osuosl.org
CC Marek Vasut <[email protected]>
CC Fabio Estevam <[email protected]>
CC Jonathan Cameron <[email protected]>
---
 drivers/staging/iio/adc/mxs-lradc.c | 45 +++++++++++++++++++++++++++++++++----
 1 file changed, 41 insertions(+), 4 deletions(-)
drivers/staging/iio/adc/mxs-lradc.c +41 -4
index 4317fee..c81b186 100644
@@ -188,20 +188,33 @@ struct mxs_lradc {
 # define LRADC_CTRL0_MX28_XNPSW	/* XM */	(1 << 17)
 # define LRADC_CTRL0_MX28_XPPSW	/* XP */	(1 << 16)
 
+# define LRADC_CTRL0_MX23_TOUCH_DETECT_ENABLE	(1 << 20)
+# define LRADC_CTRL0_MX23_YM			(1 << 19)
+# define LRADC_CTRL0_MX23_XM			(1 << 18)
+# define LRADC_CTRL0_MX23_YP			(1 << 17)
+# define LRADC_CTRL0_MX23_XP			(1 << 16)
+
 # define LRADC_CTRL0_MX28_PLATE_MASK \
 		(LRADC_CTRL0_MX28_TOUCH_DETECT_ENABLE | \
 		LRADC_CTRL0_MX28_YNNSW | LRADC_CTRL0_MX28_YPNSW | \
 		LRADC_CTRL0_MX28_YPPSW | LRADC_CTRL0_MX28_XNNSW | \
 		LRADC_CTRL0_MX28_XNPSW | LRADC_CTRL0_MX28_XPPSW)
 
+# define LRADC_CTRL0_MX23_PLATE_MASK \
+		(LRADC_CTRL0_MX23_TOUCH_DETECT_ENABLE | \
+		LRADC_CTRL0_MX23_YM | LRADC_CTRL0_MX23_XM | \
+		LRADC_CTRL0_MX23_YP | LRADC_CTRL0_MX23_XP)
+
 #define	LRADC_CTRL1				0x10
 #define	LRADC_CTRL1_TOUCH_DETECT_IRQ_EN		(1 << 24)
 #define	LRADC_CTRL1_LRADC_IRQ_EN(n)		(1 << ((n) + 16))
 #define	LRADC_CTRL1_MX28_LRADC_IRQ_EN_MASK	(0x1fff << 16)
+#define	LRADC_CTRL1_MX23_LRADC_IRQ_EN_MASK	(0x01ff << 16)
 #define	LRADC_CTRL1_LRADC_IRQ_EN_OFFSET		16
 #define	LRADC_CTRL1_TOUCH_DETECT_IRQ		(1 << 8)
 #define	LRADC_CTRL1_LRADC_IRQ(n)		(1 << (n))
 #define	LRADC_CTRL1_MX28_LRADC_IRQ_MASK		0x1fff
+#define	LRADC_CTRL1_MX23_LRADC_IRQ_MASK		0x01ff
 #define	LRADC_CTRL1_LRADC_IRQ_OFFSET		0
 
 #define	LRADC_CTRL2				0x20
@@ -252,36 +265,50 @@ static void mxs_lradc_reg(struct mxs_lradc *lradc, u32 val, u32 reg)
 
 static u32 mxs_lradc_plate_mask(struct mxs_lradc *lradc)
 {
+	if (lradc->soc == IMX23_LRADC)
+		return LRADC_CTRL0_MX23_PLATE_MASK;
 	return LRADC_CTRL0_MX28_PLATE_MASK;
 }
 
 static u32 mxs_lradc_irq_en_mask(struct mxs_lradc *lradc)
 {
+	if (lradc->soc == IMX23_LRADC)
+		return LRADC_CTRL1_MX23_LRADC_IRQ_EN_MASK;
 	return LRADC_CTRL1_MX28_LRADC_IRQ_EN_MASK;
 }
 
 static u32 mxs_lradc_irq_mask(struct mxs_lradc *lradc)
 {
+	if (lradc->soc == IMX23_LRADC)
+		return LRADC_CTRL1_MX23_LRADC_IRQ_MASK;
 	return LRADC_CTRL1_MX28_LRADC_IRQ_MASK;
 }
 
 static u32 mxs_lradc_touch_detect_bit(struct mxs_lradc *lradc)
 {
+	if (lradc->soc == IMX23_LRADC)
+		return LRADC_CTRL0_MX23_TOUCH_DETECT_ENABLE;
 	return LRADC_CTRL0_MX28_TOUCH_DETECT_ENABLE;
 }
 
 static u32 mxs_lradc_drive_x_plate(struct mxs_lradc *lradc)
 {
+	if (lradc->soc == IMX23_LRADC)
+		return LRADC_CTRL0_MX23_XP | LRADC_CTRL0_MX23_XM;
 	return LRADC_CTRL0_MX28_XPPSW | LRADC_CTRL0_MX28_XNNSW;
 }
 
 static u32 mxs_lradc_drive_y_plate(struct mxs_lradc *lradc)
 {
+	if (lradc->soc == IMX23_LRADC)
+		return LRADC_CTRL0_MX23_YP | LRADC_CTRL0_MX23_YM;
 	return LRADC_CTRL0_MX28_YPPSW | LRADC_CTRL0_MX28_YNNSW;
 }
 
 static u32 mxs_lradc_drive_pressure(struct mxs_lradc *lradc)
 {
+	if (lradc->soc == IMX23_LRADC)
+		return LRADC_CTRL0_MX23_YP | LRADC_CTRL0_MX23_XM;
 	return LRADC_CTRL0_MX28_YPPSW | LRADC_CTRL0_MX28_XNNSW;
 }
 
@@ -319,7 +346,8 @@ static int mxs_lradc_read_raw(struct iio_dev *iio_dev,
 	 * Virtual channel 0 is always used here as the others are always not
 	 * used if doing raw sampling.
 	 */
-	mxs_lradc_reg_clear(lradc, LRADC_CTRL1_MX28_LRADC_IRQ_EN_MASK,
+	if (lradc->soc == IMX28_LRADC)
+		mxs_lradc_reg_clear(lradc, LRADC_CTRL1_MX28_LRADC_IRQ_EN_MASK,
 			LRADC_CTRL1);
 	mxs_lradc_reg_clear(lradc, 0xff, LRADC_CTRL0);
 
@@ -767,7 +795,8 @@ static int mxs_lradc_buffer_preenable(struct iio_dev *iio)
 	if (ret < 0)
 		goto err_buf;
 
-	mxs_lradc_reg_clear(lradc, LRADC_CTRL1_MX28_LRADC_IRQ_EN_MASK,
+	if (lradc->soc == IMX28_LRADC)
+		mxs_lradc_reg_clear(lradc, LRADC_CTRL1_MX28_LRADC_IRQ_EN_MASK,
 							LRADC_CTRL1);
 	mxs_lradc_reg_clear(lradc, 0xff, LRADC_CTRL0);
 
@@ -805,7 +834,8 @@ static int mxs_lradc_buffer_postdisable(struct iio_dev *iio)
 					LRADC_DELAY_KICK, LRADC_DELAY(0));
 
 	mxs_lradc_reg_clear(lradc, 0xff, LRADC_CTRL0);
-	mxs_lradc_reg_clear(lradc, LRADC_CTRL1_MX28_LRADC_IRQ_EN_MASK,
+	if (lradc->soc == IMX28_LRADC)
+		mxs_lradc_reg_clear(lradc, LRADC_CTRL1_MX28_LRADC_IRQ_EN_MASK,
 					LRADC_CTRL1);
 
 	kfree(lradc->buffer);
@@ -909,7 +939,8 @@ static int mxs_lradc_hw_init(struct mxs_lradc *lradc)
 	mxs_lradc_reg(lradc, 0, LRADC_DELAY(3));
 
 	/* Configure the touchscreen type */
-	mxs_lradc_reg_clear(lradc, LRADC_CTRL0_MX28_TOUCH_SCREEN_TYPE,
+	if (lradc->soc == IMX28_LRADC) {
+		mxs_lradc_reg_clear(lradc, LRADC_CTRL0_MX28_TOUCH_SCREEN_TYPE,
 							LRADC_CTRL0);
 
 	if (lradc->use_touchscreen == MXS_LRADC_TOUCHSCREEN_5WIRE)
@@ -987,6 +1018,12 @@ static int mxs_lradc_probe(struct platform_device *pdev)
 		dev_warn(dev, "Unsupported number of touchscreen wires (%d)\n",
 				ts_wires);
 
+	if ((lradc->soc == IMX23_LRADC) && (ts_wires == 5)) {
+		dev_warn(dev, "No support for 5 wire touches on i.MX23\n");
+		dev_warn(dev, "Falling back to 4 wire\n");
+		ts_wires = 4;
+	}
+
 	/* Grab all IRQ sources */
 	for (i = 0; i < of_cfg->irq_count; i++) {
 		lradc->irq[i] = platform_get_irq(pdev, i);
Signature · 1 line
1.8.4.rc3
maintainer
#10 lore raw

PATCH 4/6 Staging/iio/adc/touchscreen/MXS: add i.MX23 support to the LRADC touchscreen driver

Quoted 5 lines · Juergen Beisert

Distinguish i.MX23 and i.MX28 at runtime and do the same for both SoC at least for the 4 wire touchscreen.

Note: support for the remaining LRADC channels is not tested on an i.MX23 yet.

An ominous comment. Are you likely to test them soon?

Minor code layout comment inline but otherwise I'm just looking for an ack from Marek.

Quoted 88 lines
---
 drivers/staging/iio/adc/mxs-lradc.c | 45 +++++++++++++++++++++++++++++++++----
 1 file changed, 41 insertions(+), 4 deletions(-)
drivers/staging/iio/adc/mxs-lradc.c +23 -0
index 4317fee..c81b186 100644
@@ -188,20 +188,33 @@ struct mxs_lradc {
 # define LRADC_CTRL0_MX28_XNPSW	/* XM */	(1 << 17)
 # define LRADC_CTRL0_MX28_XPPSW	/* XP */	(1 << 16)
 
+# define LRADC_CTRL0_MX23_TOUCH_DETECT_ENABLE	(1 << 20)
+# define LRADC_CTRL0_MX23_YM			(1 << 19)
+# define LRADC_CTRL0_MX23_XM			(1 << 18)
+# define LRADC_CTRL0_MX23_YP			(1 << 17)
+# define LRADC_CTRL0_MX23_XP			(1 << 16)
+
 # define LRADC_CTRL0_MX28_PLATE_MASK \
 		(LRADC_CTRL0_MX28_TOUCH_DETECT_ENABLE | \
 		LRADC_CTRL0_MX28_YNNSW | LRADC_CTRL0_MX28_YPNSW | \
 		LRADC_CTRL0_MX28_YPPSW | LRADC_CTRL0_MX28_XNNSW | \
 		LRADC_CTRL0_MX28_XNPSW | LRADC_CTRL0_MX28_XPPSW)
 
+# define LRADC_CTRL0_MX23_PLATE_MASK \
+		(LRADC_CTRL0_MX23_TOUCH_DETECT_ENABLE | \
+		LRADC_CTRL0_MX23_YM | LRADC_CTRL0_MX23_XM | \
+		LRADC_CTRL0_MX23_YP | LRADC_CTRL0_MX23_XP)
+
 #define	LRADC_CTRL1				0x10
 #define	LRADC_CTRL1_TOUCH_DETECT_IRQ_EN		(1 << 24)
 #define	LRADC_CTRL1_LRADC_IRQ_EN(n)		(1 << ((n) + 16))
 #define	LRADC_CTRL1_MX28_LRADC_IRQ_EN_MASK	(0x1fff << 16)
+#define	LRADC_CTRL1_MX23_LRADC_IRQ_EN_MASK	(0x01ff << 16)
 #define	LRADC_CTRL1_LRADC_IRQ_EN_OFFSET		16
 #define	LRADC_CTRL1_TOUCH_DETECT_IRQ		(1 << 8)
 #define	LRADC_CTRL1_LRADC_IRQ(n)		(1 << (n))
 #define	LRADC_CTRL1_MX28_LRADC_IRQ_MASK		0x1fff
+#define	LRADC_CTRL1_MX23_LRADC_IRQ_MASK		0x01ff
 #define	LRADC_CTRL1_LRADC_IRQ_OFFSET		0
 
 #define	LRADC_CTRL2				0x20
@@ -252,36 +265,50 @@ static void mxs_lradc_reg(struct mxs_lradc *lradc, u32 val, u32 reg)
 
 static u32 mxs_lradc_plate_mask(struct mxs_lradc *lradc)
 {
+	if (lradc->soc == IMX23_LRADC)
+		return LRADC_CTRL0_MX23_PLATE_MASK;
 	return LRADC_CTRL0_MX28_PLATE_MASK;
 }
 
 static u32 mxs_lradc_irq_en_mask(struct mxs_lradc *lradc)
 {
+	if (lradc->soc == IMX23_LRADC)
+		return LRADC_CTRL1_MX23_LRADC_IRQ_EN_MASK;
 	return LRADC_CTRL1_MX28_LRADC_IRQ_EN_MASK;
 }
 
 static u32 mxs_lradc_irq_mask(struct mxs_lradc *lradc)
 {
+	if (lradc->soc == IMX23_LRADC)
+		return LRADC_CTRL1_MX23_LRADC_IRQ_MASK;
 	return LRADC_CTRL1_MX28_LRADC_IRQ_MASK;
 }
 
 static u32 mxs_lradc_touch_detect_bit(struct mxs_lradc *lradc)
 {
+	if (lradc->soc == IMX23_LRADC)
+		return LRADC_CTRL0_MX23_TOUCH_DETECT_ENABLE;
 	return LRADC_CTRL0_MX28_TOUCH_DETECT_ENABLE;
 }
 
 static u32 mxs_lradc_drive_x_plate(struct mxs_lradc *lradc)
 {
+	if (lradc->soc == IMX23_LRADC)
+		return LRADC_CTRL0_MX23_XP | LRADC_CTRL0_MX23_XM;
 	return LRADC_CTRL0_MX28_XPPSW | LRADC_CTRL0_MX28_XNNSW;
 }
 
 static u32 mxs_lradc_drive_y_plate(struct mxs_lradc *lradc)
 {

drivers/staging/iio/adc/mxs-lradc.c static void mxs_lradc_reg(struct mxs_lradc *lradc, u32 val, u32 reg) · line 312

Quoted 10 lines
drivers/staging/iio/adc/mxs-lradc.c +4 -0
+	if (lradc->soc == IMX23_LRADC)
+		return LRADC_CTRL0_MX23_YP | LRADC_CTRL0_MX23_YM;
 	return LRADC_CTRL0_MX28_YPPSW | LRADC_CTRL0_MX28_YNNSW;
 }
 
 static u32 mxs_lradc_drive_pressure(struct mxs_lradc *lradc)
 {
+	if (lradc->soc == IMX23_LRADC)
+		return LRADC_CTRL0_MX23_YP | LRADC_CTRL0_MX23_XM;
 	return LRADC_CTRL0_MX28_YPPSW | LRADC_CTRL0_MX28_XNNSW;

Whilst it obviously doesn't actually matter, having an else in there would make the code more consistent so personally I would prefer it to be there.

Quoted 56 lines
drivers/staging/iio/adc/mxs-lradc.c +14 -4
 }
 
@@ -319,7 +346,8 @@ static int mxs_lradc_read_raw(struct iio_dev *iio_dev,
 	 * Virtual channel 0 is always used here as the others are always not
 	 * used if doing raw sampling.
 	 */
-	mxs_lradc_reg_clear(lradc, LRADC_CTRL1_MX28_LRADC_IRQ_EN_MASK,
+	if (lradc->soc == IMX28_LRADC)
+		mxs_lradc_reg_clear(lradc, LRADC_CTRL1_MX28_LRADC_IRQ_EN_MASK,
 			LRADC_CTRL1);
 	mxs_lradc_reg_clear(lradc, 0xff, LRADC_CTRL0);
 
@@ -767,7 +795,8 @@ static int mxs_lradc_buffer_preenable(struct iio_dev *iio)
 	if (ret < 0)
 		goto err_buf;
 
-	mxs_lradc_reg_clear(lradc, LRADC_CTRL1_MX28_LRADC_IRQ_EN_MASK,
+	if (lradc->soc == IMX28_LRADC)
+		mxs_lradc_reg_clear(lradc, LRADC_CTRL1_MX28_LRADC_IRQ_EN_MASK,
 							LRADC_CTRL1);
 	mxs_lradc_reg_clear(lradc, 0xff, LRADC_CTRL0);
 
@@ -805,7 +834,8 @@ static int mxs_lradc_buffer_postdisable(struct iio_dev *iio)
 					LRADC_DELAY_KICK, LRADC_DELAY(0));
 
 	mxs_lradc_reg_clear(lradc, 0xff, LRADC_CTRL0);
-	mxs_lradc_reg_clear(lradc, LRADC_CTRL1_MX28_LRADC_IRQ_EN_MASK,
+	if (lradc->soc == IMX28_LRADC)
+		mxs_lradc_reg_clear(lradc, LRADC_CTRL1_MX28_LRADC_IRQ_EN_MASK,
 					LRADC_CTRL1);
 
 	kfree(lradc->buffer);
@@ -909,7 +939,8 @@ static int mxs_lradc_hw_init(struct mxs_lradc *lradc)
 	mxs_lradc_reg(lradc, 0, LRADC_DELAY(3));
 
 	/* Configure the touchscreen type */
-	mxs_lradc_reg_clear(lradc, LRADC_CTRL0_MX28_TOUCH_SCREEN_TYPE,
+	if (lradc->soc == IMX28_LRADC) {
+		mxs_lradc_reg_clear(lradc, LRADC_CTRL0_MX28_TOUCH_SCREEN_TYPE,
 							LRADC_CTRL0);
 
 	if (lradc->use_touchscreen == MXS_LRADC_TOUCHSCREEN_5WIRE)
@@ -987,6 +1018,12 @@ static int mxs_lradc_probe(struct platform_device *pdev)
 		dev_warn(dev, "Unsupported number of touchscreen wires (%d)\n",
 				ts_wires);
 
+	if ((lradc->soc == IMX23_LRADC) && (ts_wires == 5)) {
+		dev_warn(dev, "No support for 5 wire touches on i.MX23\n");
+		dev_warn(dev, "Falling back to 4 wire\n");
+		ts_wires = 4;
+	}
+
 	/* Grab all IRQ sources */
 	for (i = 0; i < of_cfg->irq_count; i++) {
 		lradc->irq[i] = platform_get_irq(pdev, i);
#11 lore raw

PATCH 4/6 Staging/iio/adc/touchscreen/MXS: add i.MX23 support to the LRADC touchscreen driver

Hi Jonathan,

Quoted 8 lines · On Sunday 15 September 2013 12:50:09 Jonathan Cameron wrote:
Quoted 5 lines · Juergen Beisert

Distinguish i.MX23 and i.MX28 at runtime and do the same for both SoC at least for the 4 wire touchscreen.

Note: support for the remaining LRADC channels is not tested on an i.MX23 yet.

An ominous comment. Are you likely to test them soon?

Sorry, currently no i.MX28 hardware available. Someone out here with an i.MX28 based system with a touchscreen to test?

Quoted 13 lines

Minor code layout comment inline but otherwise I'm just looking for an ack from Marek.

drivers/staging/iio/adc/mxs-lradc.c static void mxs_lradc_reg(struct mxs_lradc *lradc, u32 val, u32 reg) · line 312

Quoted 6 lines

[...]
static u32 mxs_lradc_drive_pressure(struct mxs_lradc *lradc) {

drivers/staging/iio/adc/mxs-lradc.c +2 -0
+	if (lradc->soc == IMX23_LRADC)
+		return LRADC_CTRL0_MX23_YP | LRADC_CTRL0_MX23_XM;
 	return LRADC_CTRL0_MX28_YPPSW | LRADC_CTRL0_MX28_XNNSW;

Whilst it obviously doesn't actually matter, having an else in there would make the code more consistent so personally I would prefer it to be there.

I can change it. Anyone here with objections against such a change?

Regards
Juergen

Signature · 2 lines
Pengutronix e.K.                              | Juergen Beisert             |
Linux Solutions for Science and Industry      | http://www.pengutronix.de/  |
#12 lore raw

PATCH 4/6 Staging/iio/adc/touchscreen/MXS: add i.MX23 support to the LRADC touchscreen driver

Dear J?rgen Beisert,

Quoted 7 lines

Hi Jonathan,

Quoted 4 lines · On Sunday 15 September 2013 12:50:09 Jonathan Cameron wrote:
Quoted 3 lines · Juergen Beisert

Distinguish i.MX23 and i.MX28 at runtime and do the same for both SoC at least for the 4 wire touchscreen.

Quoted 7 lines
Quoted 4 lines
Quoted 2 lines

Note: support for the remaining LRADC channels is not tested on an i.MX23 yet.

An ominous comment. Are you likely to test them soon?

Sorry, currently no i.MX28 hardware available. Someone out here with an i.MX28 based system with a touchscreen to test?

You mean 23, no? I can test both, I have the DENX EVK as well as both MX23EVK and MX28EVK. Just need to find some more time to do my maintainance rounds, but that should happen this week nonetheless. If I do forget, please ping me again.

Quoted 17 lines
Quoted 8 lines

Minor code layout comment inline but otherwise I'm just looking for an ack from Marek.

Quoted 5 lines

[...]

static u32 mxs_lradc_drive_pressure(struct mxs_lradc *lradc) {

Quoted 8 lines

drivers/staging/iio/adc/mxs-lradc.c static void mxs_lradc_reg(struct mxs_lradc *lradc, u32 val, u32 reg)

Quoted 4 lines
drivers/staging/iio/adc/mxs-lradc.c +2 -0
+	if (lradc->soc == IMX23_LRADC)
+		return LRADC_CTRL0_MX23_YP | LRADC_CTRL0_MX23_XM;
 
 	return LRADC_CTRL0_MX28_YPPSW | LRADC_CTRL0_MX28_XNNSW;

Whilst it obviously doesn't actually matter, having an else in there would make the code more consistent so personally I would prefer it to be there.

Quoted 4 lines

I can change it. Anyone here with objections against such a change?

Regards
Juergen

Best regards,
Marek Vasut

#13 lore raw

PATCH 5/6 Staging/iio/adc/touchscreen/MXS: add interrupt driven touch detection

In reply to Juergen Beisert

For battery driven systems it is a very bad idea to collect the touchscreen data within a kernel busy loop.

This change uses the features of the hardware to delay and accumulate samples in hardware to avoid a high interrupt and CPU load.

Note: this is only tested on an i.MX23 SoC yet.

CC linux-arm-kernel at lists.infradead.org
CC devel at driverdev.osuosl.org
CC Marek Vasut <[email protected]>
CC Fabio Estevam <[email protected]>
CC Jonathan Cameron <[email protected]>
---
 drivers/staging/iio/adc/mxs-lradc.c | 530 ++++++++++++++++++++++++++++++++----
 1 file changed, 476 insertions(+), 54 deletions(-)
drivers/staging/iio/adc/mxs-lradc.c +476 -54
index c81b186..185f068 100644
@@ -129,6 +129,17 @@ enum mxs_lradc_ts {
 	MXS_LRADC_TOUCHSCREEN_5WIRE,
 };
 
+/*
+ * Touchscreen handling
+ */
+enum lradc_ts_plate {
+	LRADC_TOUCH = 0,
+	LRADC_SAMPLE_X,
+	LRADC_SAMPLE_Y,
+	LRADC_SAMPLE_PRESSURE,
+	LRADC_SAMPLE_VALID,
+};
+
 struct mxs_lradc {
 	struct device		*dev;
 	void __iomem		*base;
@@ -169,13 +180,25 @@ struct mxs_lradc {
 #define CHAN_MASK_TOUCHSCREEN_4WIRE	(0xf << 2)
 #define CHAN_MASK_TOUCHSCREEN_5WIRE	(0x1f << 2)
 	enum mxs_lradc_ts	use_touchscreen;
-	bool			stop_touchscreen;
 	bool			use_touchbutton;
 
 	struct input_dev	*ts_input;
 	struct work_struct	ts_work;
 
 	enum mxs_lradc_id	soc;
+	enum lradc_ts_plate	cur_plate; /* statemachine */
+	bool			ts_valid;
+	unsigned		ts_x_pos;
+	unsigned		ts_y_pos;
+	unsigned		ts_pressure;
+
+	/* handle touchscreen's physical behaviour */
+	/* samples per coordinate */
+	unsigned		over_sample_cnt;
+	/* time clocks between samples */
+	unsigned		over_sample_delay;
+	/* time in clocks to wait after the plates where switched */
+	unsigned		settling_delay;
 };
 
 #define	LRADC_CTRL0				0x00
@@ -227,19 +250,33 @@ struct mxs_lradc {
 #define	LRADC_CH_ACCUMULATE			(1 << 29)
 #define	LRADC_CH_NUM_SAMPLES_MASK		(0x1f << 24)
 #define	LRADC_CH_NUM_SAMPLES_OFFSET		24
+#define	LRADC_CH_NUM_SAMPLES(x) \
+				((x) << LRADC_CH_NUM_SAMPLES_OFFSET)
 #define	LRADC_CH_VALUE_MASK			0x3ffff
 #define	LRADC_CH_VALUE_OFFSET			0
 
 #define	LRADC_DELAY(n)				(0xd0 + (0x10 * (n)))
 #define	LRADC_DELAY_TRIGGER_LRADCS_MASK		(0xff << 24)
 #define	LRADC_DELAY_TRIGGER_LRADCS_OFFSET	24
+#define	LRADC_DELAY_TRIGGER(x) \
+				(((x) << LRADC_DELAY_TRIGGER_LRADCS_OFFSET) & \
+				LRADC_DELAY_TRIGGER_LRADCS_MASK)
 #define	LRADC_DELAY_KICK			(1 << 20)
 #define	LRADC_DELAY_TRIGGER_DELAYS_MASK		(0xf << 16)
 #define	LRADC_DELAY_TRIGGER_DELAYS_OFFSET	16
+#define	LRADC_DELAY_TRIGGER_DELAYS(x) \
+				(((x) << LRADC_DELAY_TRIGGER_DELAYS_OFFSET) & \
+				LRADC_DELAY_TRIGGER_DELAYS_MASK)
 #define	LRADC_DELAY_LOOP_COUNT_MASK		(0x1f << 11)
 #define	LRADC_DELAY_LOOP_COUNT_OFFSET		11
+#define	LRADC_DELAY_LOOP(x) \
+				(((x) << LRADC_DELAY_LOOP_COUNT_OFFSET) & \
+				LRADC_DELAY_LOOP_COUNT_MASK)
 #define	LRADC_DELAY_DELAY_MASK			0x7ff
 #define	LRADC_DELAY_DELAY_OFFSET		0
+#define	LRADC_DELAY_DELAY(x) \
+				(((x) << LRADC_DELAY_DELAY_OFFSET) & \
+				LRADC_DELAY_DELAY_MASK)
 
 #define	LRADC_CTRL4				0x140
 #define	LRADC_CTRL4_LRADCSELECT_MASK(n)		(0xf << ((n) * 4))
@@ -312,6 +349,404 @@ static u32 mxs_lradc_drive_pressure(struct mxs_lradc *lradc)
 	return LRADC_CTRL0_MX28_YPPSW | LRADC_CTRL0_MX28_XNNSW;
 }
 
+static bool mxs_lradc_check_touch_event(struct mxs_lradc *lradc)
+{
+	return !!(readl(lradc->base + LRADC_STATUS) &
+					LRADC_STATUS_TOUCH_DETECT_RAW);
+}
+
+static void mxs_lradc_setup_ts_channel(struct mxs_lradc *lradc, unsigned ch)
+{
+	/*
+	 * prepare for oversampling conversion
+	 *
+	 * from the datasheet:
+	 * "The ACCUMULATE bit in the appropriate channel register
+	 * HW_LRADC_CHn must be set to 1 if NUM_SAMPLES is greater then 0;
+	 * otherwise, the IRQs will not fire."
+	 */
+	mxs_lradc_reg(lradc, LRADC_CH_ACCUMULATE |
+			LRADC_CH_NUM_SAMPLES(lradc->over_sample_cnt - 1),
+			LRADC_CH(ch));
+
+	/* from the datasheet:
+	 * "Software must clear this register in preparation for a
+	 * multi-cycle accumulation.
+	 */
+	mxs_lradc_reg_clear(lradc, LRADC_CH_VALUE_MASK, LRADC_CH(ch));
+
+	/* prepare the delay/loop unit according to the oversampling count */
+	mxs_lradc_reg(lradc, LRADC_DELAY_TRIGGER(1 << ch) |
+		LRADC_DELAY_TRIGGER_DELAYS(0) |
+		LRADC_DELAY_LOOP(lradc->over_sample_cnt - 1) |
+		LRADC_DELAY_DELAY(lradc->over_sample_delay - 1),
+			LRADC_DELAY(3));
+
+	mxs_lradc_reg_clear(lradc, LRADC_CTRL1_LRADC_IRQ(2) |
+			LRADC_CTRL1_LRADC_IRQ(3) | LRADC_CTRL1_LRADC_IRQ(4) |
+			LRADC_CTRL1_LRADC_IRQ(5), LRADC_CTRL1);
+
+	/* wake us again, when the complete conversion is done */
+	mxs_lradc_reg_set(lradc, LRADC_CTRL1_LRADC_IRQ_EN(ch), LRADC_CTRL1);
+	/*
+	 * after changing the touchscreen plates setting
+	 * the signals need some initial time to settle. Start the
+	 * SoC's delay unit and start the conversion later
+	 * and automatically.
+	 */
+	mxs_lradc_reg(lradc, LRADC_DELAY_TRIGGER(0) | /* don't trigger ADC */
+		LRADC_DELAY_TRIGGER_DELAYS(1 << 3) | /* trigger DELAY unit#3 */
+		LRADC_DELAY_KICK |
+		LRADC_DELAY_DELAY(lradc->settling_delay),
+			LRADC_DELAY(2));
+}
+
+/*
+ * Pressure detection is special:
+ * We want to do both required measurements for the pressure detection in
+ * one turn. Use the hardware features to chain both conversions and let the
+ * hardware report one interrupt if both conversions are done
+ */
+static void mxs_lradc_setup_ts_pressure(struct mxs_lradc *lradc, unsigned ch1,
+							unsigned ch2)
+{
+	u32 reg;
+
+	/*
+	 * prepare for oversampling conversion
+	 *
+	 * from the datasheet:
+	 * "The ACCUMULATE bit in the appropriate channel register
+	 * HW_LRADC_CHn must be set to 1 if NUM_SAMPLES is greater then 0;
+	 * otherwise, the IRQs will not fire."
+	 */
+	reg = LRADC_CH_ACCUMULATE |
+		LRADC_CH_NUM_SAMPLES(lradc->over_sample_cnt - 1);
+	mxs_lradc_reg(lradc, reg, LRADC_CH(ch1));
+	mxs_lradc_reg(lradc, reg, LRADC_CH(ch2));
+
+	/* from the datasheet:
+	 * "Software must clear this register in preparation for a
+	 * multi-cycle accumulation.
+	 */
+	mxs_lradc_reg_clear(lradc, LRADC_CH_VALUE_MASK, LRADC_CH(ch1));
+	mxs_lradc_reg_clear(lradc, LRADC_CH_VALUE_MASK, LRADC_CH(ch2));
+
+	/* prepare the delay/loop unit according to the oversampling count */
+	mxs_lradc_reg(lradc, LRADC_DELAY_TRIGGER(1 << ch1) |
+		LRADC_DELAY_TRIGGER(1 << ch2) | /* start both channels */
+		LRADC_DELAY_TRIGGER_DELAYS(0) |
+		LRADC_DELAY_LOOP(lradc->over_sample_cnt - 1) |
+		LRADC_DELAY_DELAY(lradc->over_sample_delay - 1),
+					LRADC_DELAY(3));
+
+	mxs_lradc_reg_clear(lradc, LRADC_CTRL1_LRADC_IRQ(2) |
+			LRADC_CTRL1_LRADC_IRQ(3) | LRADC_CTRL1_LRADC_IRQ(4) |
+			LRADC_CTRL1_LRADC_IRQ(5), LRADC_CTRL1);
+
+	/* wake us again, when the conversions are done */
+	mxs_lradc_reg_set(lradc, LRADC_CTRL1_LRADC_IRQ_EN(ch2), LRADC_CTRL1);
+	/*
+	 * after changing the touchscreen plates setting
+	 * the signals need some initial time to settle. Start the
+	 * SoC's delay unit and start the conversion later
+	 * and automatically.
+	 */
+	mxs_lradc_reg(lradc, LRADC_DELAY_TRIGGER(0) | /* don't trigger ADC */
+		LRADC_DELAY_TRIGGER_DELAYS(1 << 3) | /* trigger DELAY unit#3 */
+		LRADC_DELAY_KICK |
+		LRADC_DELAY_DELAY(lradc->settling_delay), LRADC_DELAY(2));
+}
+
+static unsigned mxs_lradc_read_raw_channel(struct mxs_lradc *lradc,
+							unsigned channel)
+{
+	u32 reg;
+	unsigned num_samples, val;
+
+	reg = readl(lradc->base + LRADC_CH(channel));
+	if (reg & LRADC_CH_ACCUMULATE)
+		num_samples = lradc->over_sample_cnt;
+	else
+		num_samples = 1;
+
+	val = (reg & LRADC_CH_VALUE_MASK) >> LRADC_CH_VALUE_OFFSET;
+	return val / num_samples;
+}
+
+static unsigned mxs_lradc_read_ts_pressure(struct mxs_lradc *lradc,
+						unsigned ch1, unsigned ch2)
+{
+	u32 reg, mask;
+	unsigned pressure, m1, m2;
+
+	mask = LRADC_CTRL1_LRADC_IRQ(ch1) | LRADC_CTRL1_LRADC_IRQ(ch2);
+	reg = readl(lradc->base + LRADC_CTRL1) & mask;
+
+	while (reg != mask) {
+		reg = readl(lradc->base + LRADC_CTRL1) & mask;
+		dev_dbg(lradc->dev, "One channel is still busy: %X\n", reg);
+	}
+
+	m1 = mxs_lradc_read_raw_channel(lradc, ch1);
+	m2 = mxs_lradc_read_raw_channel(lradc, ch2);
+
+	if (m2 == 0) {
+		dev_warn(lradc->dev, "Cannot calculate pressure\n");
+		return 1 << (LRADC_RESOLUTION - 1);
+	}
+
+	/* simply scale the value from 0 ... max ADC resolution */
+	pressure = m1;
+	pressure *= (1 << LRADC_RESOLUTION);
+	pressure /= m2;
+
+	dev_dbg(lradc->dev, "Pressure = %u\n", pressure);
+	return pressure;
+}
+
+#define TS_CH_XP 2
+#define TS_CH_YP 3
+#define TS_CH_XM 4
+#define TS_CH_YM 5
+
+static int mxs_lradc_read_ts_channel(struct mxs_lradc *lradc)
+{
+	u32 reg;
+	int val;
+
+	reg = readl(lradc->base + LRADC_CTRL1);
+
+	/* only channels 3 to 5 are of interest here */
+	if (reg & LRADC_CTRL1_LRADC_IRQ(TS_CH_YP)) {
+		mxs_lradc_reg_clear(lradc, LRADC_CTRL1_LRADC_IRQ_EN(TS_CH_YP) |
+			LRADC_CTRL1_LRADC_IRQ(TS_CH_YP), LRADC_CTRL1);
+		val = mxs_lradc_read_raw_channel(lradc, TS_CH_YP);
+	} else if (reg & LRADC_CTRL1_LRADC_IRQ(TS_CH_XM)) {
+		mxs_lradc_reg_clear(lradc, LRADC_CTRL1_LRADC_IRQ_EN(TS_CH_XM) |
+			LRADC_CTRL1_LRADC_IRQ(TS_CH_XM), LRADC_CTRL1);
+		val = mxs_lradc_read_raw_channel(lradc, TS_CH_XM);
+	} else if (reg & LRADC_CTRL1_LRADC_IRQ(TS_CH_YM)) {
+		mxs_lradc_reg_clear(lradc, LRADC_CTRL1_LRADC_IRQ_EN(TS_CH_YM) |
+			LRADC_CTRL1_LRADC_IRQ(TS_CH_YM), LRADC_CTRL1);
+		val = mxs_lradc_read_raw_channel(lradc, TS_CH_YM);
+	} else {
+		return -EIO;
+	}
+
+	mxs_lradc_reg(lradc, 0, LRADC_DELAY(2));
+	mxs_lradc_reg(lradc, 0, LRADC_DELAY(3));
+
+	return val;
+}
+
+/*
+ * YP(open)--+-------------+
+ *           |             |--+
+ *           |             |  |
+ *    YM(-)--+-------------+  |
+ *             +--------------+
+ *             |              |
+ *         XP(weak+)        XM(open)
+ *
+ * "weak+" means 200k Ohm VDDIO
+ * (-) means GND
+ */
+static void mxs_lradc_setup_touch_detection(struct mxs_lradc *lradc)
+{
+	/*
+	 * In order to detect a touch event the 'touch detect enable' bit
+	 * enables:
+	 *  - a weak pullup to the X+ connector
+	 *  - a strong ground at the Y- connector
+	 */
+	mxs_lradc_reg_clear(lradc, mxs_lradc_plate_mask(lradc), LRADC_CTRL0);
+	mxs_lradc_reg_set(lradc, mxs_lradc_touch_detect_bit(lradc),
+				LRADC_CTRL0);
+}
+
+/*
+ * YP(meas)--+-------------+
+ *           |             |--+
+ *           |             |  |
+ * YM(open)--+-------------+  |
+ *             +--------------+
+ *             |              |
+ *           XP(+)          XM(-)
+ *
+ * (+) means here 1.85 V
+ * (-) means here GND
+ */
+static void mxs_lradc_prepare_x_pos(struct mxs_lradc *lradc)
+{
+	mxs_lradc_reg_clear(lradc, mxs_lradc_plate_mask(lradc), LRADC_CTRL0);
+	mxs_lradc_reg_set(lradc, mxs_lradc_drive_x_plate(lradc), LRADC_CTRL0);
+
+	lradc->cur_plate = LRADC_SAMPLE_X;
+	mxs_lradc_setup_ts_channel(lradc, TS_CH_YP);
+}
+
+/*
+ *   YP(+)--+-------------+
+ *          |             |--+
+ *          |             |  |
+ *   YM(-)--+-------------+  |
+ *            +--------------+
+ *            |              |
+ *         XP(open)        XM(meas)
+ *
+ * (+) means here 1.85 V
+ * (-) means here GND
+ */
+static void mxs_lradc_prepare_y_pos(struct mxs_lradc *lradc)
+{
+	mxs_lradc_reg_clear(lradc, mxs_lradc_plate_mask(lradc), LRADC_CTRL0);
+	mxs_lradc_reg_set(lradc, mxs_lradc_drive_y_plate(lradc), LRADC_CTRL0);
+
+	lradc->cur_plate = LRADC_SAMPLE_Y;
+	mxs_lradc_setup_ts_channel(lradc, TS_CH_XM);
+}
+
+/*
+ *    YP(+)--+-------------+
+ *           |             |--+
+ *           |             |  |
+ * YM(meas)--+-------------+  |
+ *             +--------------+
+ *             |              |
+ *          XP(meas)        XM(-)
+ *
+ * (+) means here 1.85 V
+ * (-) means here GND
+ */
+static void mxs_lradc_prepare_pressure(struct mxs_lradc *lradc)
+{
+	mxs_lradc_reg_clear(lradc, mxs_lradc_plate_mask(lradc), LRADC_CTRL0);
+	mxs_lradc_reg_set(lradc, mxs_lradc_drive_pressure(lradc), LRADC_CTRL0);
+
+	lradc->cur_plate = LRADC_SAMPLE_PRESSURE;
+	mxs_lradc_setup_ts_pressure(lradc, TS_CH_XP, TS_CH_YM);
+}
+
+static void mxs_lradc_enable_touch_detection(struct mxs_lradc *lradc)
+{
+	mxs_lradc_setup_touch_detection(lradc);
+
+	lradc->cur_plate = LRADC_TOUCH;
+	mxs_lradc_reg_clear(lradc, LRADC_CTRL1_TOUCH_DETECT_IRQ |
+				LRADC_CTRL1_TOUCH_DETECT_IRQ_EN, LRADC_CTRL1);
+	mxs_lradc_reg_set(lradc, LRADC_CTRL1_TOUCH_DETECT_IRQ_EN, LRADC_CTRL1);
+}
+
+static void mxs_lradc_report_ts_event(struct mxs_lradc *lradc)
+{
+	input_report_abs(lradc->ts_input, ABS_X, lradc->ts_x_pos);
+	input_report_abs(lradc->ts_input, ABS_Y, lradc->ts_y_pos);
+	input_report_abs(lradc->ts_input, ABS_PRESSURE, lradc->ts_pressure);
+	input_report_key(lradc->ts_input, BTN_TOUCH, 1);
+	input_sync(lradc->ts_input);
+}
+
+static void mxs_lradc_complete_touch_event(struct mxs_lradc *lradc)
+{
+	mxs_lradc_setup_touch_detection(lradc);
+	lradc->cur_plate = LRADC_SAMPLE_VALID;
+	/*
+	 * start a dummy conversion to burn time to settle the signals
+	 * note: we are not interested in the conversion's value
+	 */
+	mxs_lradc_reg(lradc, 0, LRADC_CH(5));
+	mxs_lradc_reg_clear(lradc, LRADC_CTRL1_LRADC_IRQ(5), LRADC_CTRL1);
+	mxs_lradc_reg_set(lradc, LRADC_CTRL1_LRADC_IRQ_EN(5), LRADC_CTRL1);
+	mxs_lradc_reg(lradc, LRADC_DELAY_TRIGGER(1 << 5) |
+		LRADC_DELAY_KICK | LRADC_DELAY_DELAY(10), /* waste 5 ms */
+			LRADC_DELAY(2));
+}
+
+/*
+ * in order to avoid false measurements, report only samples where
+ * the surface is still touched after the position measurement
+ */
+static void mxs_lradc_finish_touch_event(struct mxs_lradc *lradc, bool valid)
+{
+	/* if it is still touched, report the sample */
+	if (valid && mxs_lradc_check_touch_event(lradc)) {
+		lradc->ts_valid = true;
+		mxs_lradc_report_ts_event(lradc);
+	}
+
+	/* if it is even still touched, continue with the next measurement */
+	if (mxs_lradc_check_touch_event(lradc)) {
+		mxs_lradc_prepare_y_pos(lradc);
+		return;
+	}
+
+	if (lradc->ts_valid) {
+		/* signal the release */
+		lradc->ts_valid = false;
+		input_report_key(lradc->ts_input, BTN_TOUCH, 0);
+		input_sync(lradc->ts_input);
+	}
+
+	/* if it is released, wait for the next touch via IRQ */
+	mxs_lradc_reg_clear(lradc, LRADC_CTRL1_TOUCH_DETECT_IRQ, LRADC_CTRL1);
+	mxs_lradc_reg_set(lradc, LRADC_CTRL1_TOUCH_DETECT_IRQ_EN, LRADC_CTRL1);
+}
+
+/* touchscreen's state machine */
+static void mxs_lradc_handle_touch(struct mxs_lradc *lradc)
+{
+	int val;
+
+	switch (lradc->cur_plate) {
+	case LRADC_TOUCH:
+		/*
+		 * start with the Y-pos, because it uses nearly the same plate
+		 * settings like the touch detection
+		 */
+		if (mxs_lradc_check_touch_event(lradc)) {
+			mxs_lradc_reg_clear(lradc,
+					LRADC_CTRL1_TOUCH_DETECT_IRQ_EN,
+					LRADC_CTRL1);
+			mxs_lradc_prepare_y_pos(lradc);
+		}
+		mxs_lradc_reg_clear(lradc, LRADC_CTRL1_TOUCH_DETECT_IRQ,
+					LRADC_CTRL1);
+		return;
+
+	case LRADC_SAMPLE_Y:
+		val = mxs_lradc_read_ts_channel(lradc);
+		if (val < 0) {
+			mxs_lradc_enable_touch_detection(lradc); /* re-start */
+			return;
+		}
+		lradc->ts_y_pos = val;
+		mxs_lradc_prepare_x_pos(lradc);
+		return;
+
+	case LRADC_SAMPLE_X:
+		val = mxs_lradc_read_ts_channel(lradc);
+		if (val < 0) {
+			mxs_lradc_enable_touch_detection(lradc); /* re-start */
+			return;
+		}
+		lradc->ts_x_pos = val;
+		mxs_lradc_prepare_pressure(lradc);
+		return;
+
+	case LRADC_SAMPLE_PRESSURE:
+		lradc->ts_pressure =
+			mxs_lradc_read_ts_pressure(lradc, TS_CH_XP, TS_CH_YM);
+		mxs_lradc_complete_touch_event(lradc);
+		return;
+
+	case LRADC_SAMPLE_VALID:
+		val = mxs_lradc_read_ts_channel(lradc); /* ignore the value */
+		mxs_lradc_finish_touch_event(lradc, 1);
+		break;
+	}
+}
+
 /*
  * Raw I/O operations
  */
@@ -385,15 +820,6 @@ static const struct iio_info mxs_lradc_iio_info = {
 	.read_raw		= mxs_lradc_read_raw,
 };
 
-/*
- * Touchscreen handling
- */
-enum lradc_ts_plate {
-	LRADC_SAMPLE_X,
-	LRADC_SAMPLE_Y,
-	LRADC_SAMPLE_PRESSURE,
-};
-
 static int mxs_lradc_ts_touched(struct mxs_lradc *lradc)
 {
 	uint32_t reg;
@@ -551,10 +977,6 @@ static void mxs_lradc_ts_work(struct work_struct *ts_work)
 	input_report_key(lradc->ts_input, BTN_TOUCH, 0);
 	input_sync(lradc->ts_input);
 
-	/* Do not restart the TS IRQ if the driver is shutting down. */
-	if (lradc->stop_touchscreen)
-		return;
-
 	/* Restart the touchscreen interrupts. */
 	mxs_lradc_reg_clear(lradc, LRADC_CTRL1_TOUCH_DETECT_IRQ, LRADC_CTRL1);
 	mxs_lradc_reg_set(lradc, LRADC_CTRL1_TOUCH_DETECT_IRQ_EN, LRADC_CTRL1);
@@ -564,36 +986,29 @@ static int mxs_lradc_ts_open(struct input_dev *dev)
 {
 	struct mxs_lradc *lradc = input_get_drvdata(dev);
 
-	/* The touchscreen is starting. */
-	lradc->stop_touchscreen = false;
-
 	/* Enable the touch-detect circuitry. */
-	mxs_lradc_reg_set(lradc, mxs_lradc_touch_detect_bit(lradc),
-						LRADC_CTRL0);
-
-	/* Enable the touch-detect IRQ. */
-	mxs_lradc_reg_set(lradc, LRADC_CTRL1_TOUCH_DETECT_IRQ_EN, LRADC_CTRL1);
+	mxs_lradc_enable_touch_detection(lradc);
 
 	return 0;
 }
 
-static void mxs_lradc_ts_close(struct input_dev *dev)
+static void mxs_lradc_disable_ts(struct mxs_lradc *lradc)
 {
-	struct mxs_lradc *lradc = input_get_drvdata(dev);
-
-	/* Indicate the touchscreen is stopping. */
-	lradc->stop_touchscreen = true;
-	mb();
+	/* stop all interrupts from firing */
+	mxs_lradc_reg_clear(lradc, LRADC_CTRL1_TOUCH_DETECT_IRQ_EN |
+		LRADC_CTRL1_LRADC_IRQ_EN(2) | LRADC_CTRL1_LRADC_IRQ_EN(3) |
+		LRADC_CTRL1_LRADC_IRQ_EN(4) | LRADC_CTRL1_LRADC_IRQ_EN(5),
+		LRADC_CTRL1);
 
-	/* Wait until touchscreen thread finishes any possible remnants. */
-	cancel_work_sync(&lradc->ts_work);
+	/* Power-down touchscreen touch-detect circuitry. */
+	mxs_lradc_reg_clear(lradc, mxs_lradc_plate_mask(lradc), LRADC_CTRL0);
+}
 
-	/* Disable touchscreen touch-detect IRQ. */
-	mxs_lradc_reg_clear(lradc, LRADC_CTRL1_TOUCH_DETECT_IRQ_EN,
-						LRADC_CTRL1);
+static void mxs_lradc_ts_close(struct input_dev *dev)
+{
+	struct mxs_lradc *lradc = input_get_drvdata(dev);
 
-	/* Power-down touchscreen touch-detect circuitry. */
-	mxs_lradc_reg_clear(lradc, mxs_lradc_touch_detect_bit(lradc), LRADC_CTRL0);
+	mxs_lradc_disable_ts(lradc);
 }
 
 static int mxs_lradc_ts_register(struct mxs_lradc *lradc)
@@ -641,6 +1056,7 @@ static void mxs_lradc_ts_unregister(struct mxs_lradc *lradc)
 
 	cancel_work_sync(&lradc->ts_work);
 
+	mxs_lradc_disable_ts(lradc);
 	input_unregister_device(lradc->ts_input);
 }
 
@@ -653,30 +1069,23 @@ static irqreturn_t mxs_lradc_handle_irq(int irq, void *data)
 	struct mxs_lradc *lradc = iio_priv(iio);
 	unsigned long reg = readl(lradc->base + LRADC_CTRL1);
 	const uint32_t ts_irq_mask =
-		LRADC_CTRL1_TOUCH_DETECT_IRQ_EN |
-		LRADC_CTRL1_TOUCH_DETECT_IRQ;
+		LRADC_CTRL1_TOUCH_DETECT_IRQ |
+		LRADC_CTRL1_LRADC_IRQ(2) |
+		LRADC_CTRL1_LRADC_IRQ(3) |
+		LRADC_CTRL1_LRADC_IRQ(4) |
+		LRADC_CTRL1_LRADC_IRQ(5);
 
 	if (!(reg & mxs_lradc_irq_mask(lradc)))
 		return IRQ_NONE;
 
-	/*
-	 * Touchscreen IRQ handling code has priority and therefore
-	 * is placed here. In case touchscreen IRQ arrives, disable
-	 * it ASAP
-	 */
-	if (reg & LRADC_CTRL1_TOUCH_DETECT_IRQ) {
-		mxs_lradc_reg_clear(lradc, ts_irq_mask, LRADC_CTRL1);
-		if (!lradc->stop_touchscreen)
-			schedule_work(&lradc->ts_work);
-	}
+	if (lradc->use_touchscreen && (reg & ts_irq_mask))
+		mxs_lradc_handle_touch(lradc);
 
 	if (iio_buffer_enabled(iio))
 		iio_trigger_poll(iio->trig, iio_get_time_ns());
 	else if (reg & LRADC_CTRL1_LRADC_IRQ(0))
 		complete(&lradc->completion);
 
-	mxs_lradc_reg_clear(lradc, reg & mxs_lradc_irq_mask(lradc), LRADC_CTRL1);
-
 	return IRQ_HANDLED;
 }
 
@@ -971,6 +1380,17 @@ static const struct of_device_id mxs_lradc_dt_ids[] = {
 };
 MODULE_DEVICE_TABLE(of, mxs_lradc_dt_ids);
 
+static int mxs_lradc_probe_touchscreen(struct mxs_lradc *lradc,
+						struct device_node *lradc_node)
+{
+	/* TODO retrieve from device tree */
+	lradc->over_sample_cnt = 4;
+	lradc->over_sample_delay = 2;
+	lradc->settling_delay = 10;
+
+	return 0;
+}
+
 static int mxs_lradc_probe(struct platform_device *pdev)
 {
 	const struct of_device_id *of_id =
@@ -983,7 +1403,7 @@ static int mxs_lradc_probe(struct platform_device *pdev)
 	struct iio_dev *iio;
 	struct resource *iores;
 	uint32_t ts_wires = 0;
-	int ret = 0;
+	int ret = 0, touch_ret;
 	int i;
 
 	/* Allocate the IIO device. */
@@ -1003,7 +1423,7 @@ static int mxs_lradc_probe(struct platform_device *pdev)
 	if (IS_ERR(lradc->base))
 		return PTR_ERR(lradc->base);
 
-	INIT_WORK(&lradc->ts_work, mxs_lradc_ts_work);
+	touch_ret = mxs_lradc_probe_touchscreen(lradc, node);
 
 	/* Check if touchscreen is enabled in DT. */
 	ret = of_property_read_u32(node, "fsl,lradc-touchscreen-wires",
@@ -1066,9 +1486,11 @@ static int mxs_lradc_probe(struct platform_device *pdev)
 		goto err_dev;
 
 	/* Register the touchscreen input device. */
-	ret = mxs_lradc_ts_register(lradc);
-	if (ret)
-		goto err_dev;
+	if (touch_ret == 0) {
+		ret = mxs_lradc_ts_register(lradc);
+		if (ret)
+			goto err_dev;
+	}
 
 	/* Register IIO device. */
 	ret = iio_device_register(iio);
Signature · 1 line
1.8.4.rc3
maintainer
#14 lore raw

PATCH 5/6 Staging/iio/adc/touchscreen/MXS: add interrupt driven touch detection

Quoted 6 lines · Juergen Beisert

For battery driven systems it is a very bad idea to collect the touchscreen data within a kernel busy loop.

This change uses the features of the hardware to delay and accumulate samples in hardware to avoid a high interrupt and CPU load.

Quoted 8 lines

Note: this is only tested on an i.MX23 SoC yet.

While this driver is placed in IIO within staging at the moment, these changes are definitely input related. Hence I have cc'd Dmitry and the input list.

I am personaly a little uncomfortable that we have such a complex bit of input code sat within an IIO driver but such is life.

Quoted 668 lines
---
 drivers/staging/iio/adc/mxs-lradc.c | 530 ++++++++++++++++++++++++++++++++----
 1 file changed, 476 insertions(+), 54 deletions(-)
drivers/staging/iio/adc/mxs-lradc.c +476 -54
index c81b186..185f068 100644
@@ -129,6 +129,17 @@ enum mxs_lradc_ts {
 	MXS_LRADC_TOUCHSCREEN_5WIRE,
 };
 
+/*
+ * Touchscreen handling
+ */
+enum lradc_ts_plate {
+	LRADC_TOUCH = 0,
+	LRADC_SAMPLE_X,
+	LRADC_SAMPLE_Y,
+	LRADC_SAMPLE_PRESSURE,
+	LRADC_SAMPLE_VALID,
+};
+
 struct mxs_lradc {
 	struct device		*dev;
 	void __iomem		*base;
@@ -169,13 +180,25 @@ struct mxs_lradc {
 #define CHAN_MASK_TOUCHSCREEN_4WIRE	(0xf << 2)
 #define CHAN_MASK_TOUCHSCREEN_5WIRE	(0x1f << 2)
 	enum mxs_lradc_ts	use_touchscreen;
-	bool			stop_touchscreen;
 	bool			use_touchbutton;
 
 	struct input_dev	*ts_input;
 	struct work_struct	ts_work;
 
 	enum mxs_lradc_id	soc;
+	enum lradc_ts_plate	cur_plate; /* statemachine */
+	bool			ts_valid;
+	unsigned		ts_x_pos;
+	unsigned		ts_y_pos;
+	unsigned		ts_pressure;
+
+	/* handle touchscreen's physical behaviour */
+	/* samples per coordinate */
+	unsigned		over_sample_cnt;
+	/* time clocks between samples */
+	unsigned		over_sample_delay;
+	/* time in clocks to wait after the plates where switched */
+	unsigned		settling_delay;
 };
 
 #define	LRADC_CTRL0				0x00
@@ -227,19 +250,33 @@ struct mxs_lradc {
 #define	LRADC_CH_ACCUMULATE			(1 << 29)
 #define	LRADC_CH_NUM_SAMPLES_MASK		(0x1f << 24)
 #define	LRADC_CH_NUM_SAMPLES_OFFSET		24
+#define	LRADC_CH_NUM_SAMPLES(x) \
+				((x) << LRADC_CH_NUM_SAMPLES_OFFSET)
 #define	LRADC_CH_VALUE_MASK			0x3ffff
 #define	LRADC_CH_VALUE_OFFSET			0
 
 #define	LRADC_DELAY(n)				(0xd0 + (0x10 * (n)))
 #define	LRADC_DELAY_TRIGGER_LRADCS_MASK		(0xff << 24)
 #define	LRADC_DELAY_TRIGGER_LRADCS_OFFSET	24
+#define	LRADC_DELAY_TRIGGER(x) \
+				(((x) << LRADC_DELAY_TRIGGER_LRADCS_OFFSET) & \
+				LRADC_DELAY_TRIGGER_LRADCS_MASK)
 #define	LRADC_DELAY_KICK			(1 << 20)
 #define	LRADC_DELAY_TRIGGER_DELAYS_MASK		(0xf << 16)
 #define	LRADC_DELAY_TRIGGER_DELAYS_OFFSET	16
+#define	LRADC_DELAY_TRIGGER_DELAYS(x) \
+				(((x) << LRADC_DELAY_TRIGGER_DELAYS_OFFSET) & \
+				LRADC_DELAY_TRIGGER_DELAYS_MASK)
 #define	LRADC_DELAY_LOOP_COUNT_MASK		(0x1f << 11)
 #define	LRADC_DELAY_LOOP_COUNT_OFFSET		11
+#define	LRADC_DELAY_LOOP(x) \
+				(((x) << LRADC_DELAY_LOOP_COUNT_OFFSET) & \
+				LRADC_DELAY_LOOP_COUNT_MASK)
 #define	LRADC_DELAY_DELAY_MASK			0x7ff
 #define	LRADC_DELAY_DELAY_OFFSET		0
+#define	LRADC_DELAY_DELAY(x) \
+				(((x) << LRADC_DELAY_DELAY_OFFSET) & \
+				LRADC_DELAY_DELAY_MASK)
 
 #define	LRADC_CTRL4				0x140
 #define	LRADC_CTRL4_LRADCSELECT_MASK(n)		(0xf << ((n) * 4))
@@ -312,6 +349,404 @@ static u32 mxs_lradc_drive_pressure(struct mxs_lradc *lradc)
 	return LRADC_CTRL0_MX28_YPPSW | LRADC_CTRL0_MX28_XNNSW;
 }
 
+static bool mxs_lradc_check_touch_event(struct mxs_lradc *lradc)
+{
+	return !!(readl(lradc->base + LRADC_STATUS) &
+					LRADC_STATUS_TOUCH_DETECT_RAW);
+}
+
+static void mxs_lradc_setup_ts_channel(struct mxs_lradc *lradc, unsigned ch)
+{
+	/*
+	 * prepare for oversampling conversion
+	 *
+	 * from the datasheet:
+	 * "The ACCUMULATE bit in the appropriate channel register
+	 * HW_LRADC_CHn must be set to 1 if NUM_SAMPLES is greater then 0;
+	 * otherwise, the IRQs will not fire."
+	 */
+	mxs_lradc_reg(lradc, LRADC_CH_ACCUMULATE |
+			LRADC_CH_NUM_SAMPLES(lradc->over_sample_cnt - 1),
+			LRADC_CH(ch));
+
+	/* from the datasheet:
+	 * "Software must clear this register in preparation for a
+	 * multi-cycle accumulation.
+	 */
+	mxs_lradc_reg_clear(lradc, LRADC_CH_VALUE_MASK, LRADC_CH(ch));
+
+	/* prepare the delay/loop unit according to the oversampling count */
+	mxs_lradc_reg(lradc, LRADC_DELAY_TRIGGER(1 << ch) |
+		LRADC_DELAY_TRIGGER_DELAYS(0) |
+		LRADC_DELAY_LOOP(lradc->over_sample_cnt - 1) |
+		LRADC_DELAY_DELAY(lradc->over_sample_delay - 1),
+			LRADC_DELAY(3));
+
+	mxs_lradc_reg_clear(lradc, LRADC_CTRL1_LRADC_IRQ(2) |
+			LRADC_CTRL1_LRADC_IRQ(3) | LRADC_CTRL1_LRADC_IRQ(4) |
+			LRADC_CTRL1_LRADC_IRQ(5), LRADC_CTRL1);
+
+	/* wake us again, when the complete conversion is done */
+	mxs_lradc_reg_set(lradc, LRADC_CTRL1_LRADC_IRQ_EN(ch), LRADC_CTRL1);
+	/*
+	 * after changing the touchscreen plates setting
+	 * the signals need some initial time to settle. Start the
+	 * SoC's delay unit and start the conversion later
+	 * and automatically.
+	 */
+	mxs_lradc_reg(lradc, LRADC_DELAY_TRIGGER(0) | /* don't trigger ADC */
+		LRADC_DELAY_TRIGGER_DELAYS(1 << 3) | /* trigger DELAY unit#3 */
+		LRADC_DELAY_KICK |
+		LRADC_DELAY_DELAY(lradc->settling_delay),
+			LRADC_DELAY(2));
+}
+
+/*
+ * Pressure detection is special:
+ * We want to do both required measurements for the pressure detection in
+ * one turn. Use the hardware features to chain both conversions and let the
+ * hardware report one interrupt if both conversions are done
+ */
+static void mxs_lradc_setup_ts_pressure(struct mxs_lradc *lradc, unsigned ch1,
+							unsigned ch2)
+{
+	u32 reg;
+
+	/*
+	 * prepare for oversampling conversion
+	 *
+	 * from the datasheet:
+	 * "The ACCUMULATE bit in the appropriate channel register
+	 * HW_LRADC_CHn must be set to 1 if NUM_SAMPLES is greater then 0;
+	 * otherwise, the IRQs will not fire."
+	 */
+	reg = LRADC_CH_ACCUMULATE |
+		LRADC_CH_NUM_SAMPLES(lradc->over_sample_cnt - 1);
+	mxs_lradc_reg(lradc, reg, LRADC_CH(ch1));
+	mxs_lradc_reg(lradc, reg, LRADC_CH(ch2));
+
+	/* from the datasheet:
+	 * "Software must clear this register in preparation for a
+	 * multi-cycle accumulation.
+	 */
+	mxs_lradc_reg_clear(lradc, LRADC_CH_VALUE_MASK, LRADC_CH(ch1));
+	mxs_lradc_reg_clear(lradc, LRADC_CH_VALUE_MASK, LRADC_CH(ch2));
+
+	/* prepare the delay/loop unit according to the oversampling count */
+	mxs_lradc_reg(lradc, LRADC_DELAY_TRIGGER(1 << ch1) |
+		LRADC_DELAY_TRIGGER(1 << ch2) | /* start both channels */
+		LRADC_DELAY_TRIGGER_DELAYS(0) |
+		LRADC_DELAY_LOOP(lradc->over_sample_cnt - 1) |
+		LRADC_DELAY_DELAY(lradc->over_sample_delay - 1),
+					LRADC_DELAY(3));
+
+	mxs_lradc_reg_clear(lradc, LRADC_CTRL1_LRADC_IRQ(2) |
+			LRADC_CTRL1_LRADC_IRQ(3) | LRADC_CTRL1_LRADC_IRQ(4) |
+			LRADC_CTRL1_LRADC_IRQ(5), LRADC_CTRL1);
+
+	/* wake us again, when the conversions are done */
+	mxs_lradc_reg_set(lradc, LRADC_CTRL1_LRADC_IRQ_EN(ch2), LRADC_CTRL1);
+	/*
+	 * after changing the touchscreen plates setting
+	 * the signals need some initial time to settle. Start the
+	 * SoC's delay unit and start the conversion later
+	 * and automatically.
+	 */
+	mxs_lradc_reg(lradc, LRADC_DELAY_TRIGGER(0) | /* don't trigger ADC */
+		LRADC_DELAY_TRIGGER_DELAYS(1 << 3) | /* trigger DELAY unit#3 */
+		LRADC_DELAY_KICK |
+		LRADC_DELAY_DELAY(lradc->settling_delay), LRADC_DELAY(2));
+}
+
+static unsigned mxs_lradc_read_raw_channel(struct mxs_lradc *lradc,
+							unsigned channel)
+{
+	u32 reg;
+	unsigned num_samples, val;
+
+	reg = readl(lradc->base + LRADC_CH(channel));
+	if (reg & LRADC_CH_ACCUMULATE)
+		num_samples = lradc->over_sample_cnt;
+	else
+		num_samples = 1;
+
+	val = (reg & LRADC_CH_VALUE_MASK) >> LRADC_CH_VALUE_OFFSET;
+	return val / num_samples;
+}
+
+static unsigned mxs_lradc_read_ts_pressure(struct mxs_lradc *lradc,
+						unsigned ch1, unsigned ch2)
+{
+	u32 reg, mask;
+	unsigned pressure, m1, m2;
+
+	mask = LRADC_CTRL1_LRADC_IRQ(ch1) | LRADC_CTRL1_LRADC_IRQ(ch2);
+	reg = readl(lradc->base + LRADC_CTRL1) & mask;
+
+	while (reg != mask) {
+		reg = readl(lradc->base + LRADC_CTRL1) & mask;
+		dev_dbg(lradc->dev, "One channel is still busy: %X\n", reg);
+	}
+
+	m1 = mxs_lradc_read_raw_channel(lradc, ch1);
+	m2 = mxs_lradc_read_raw_channel(lradc, ch2);
+
+	if (m2 == 0) {
+		dev_warn(lradc->dev, "Cannot calculate pressure\n");
+		return 1 << (LRADC_RESOLUTION - 1);
+	}
+
+	/* simply scale the value from 0 ... max ADC resolution */
+	pressure = m1;
+	pressure *= (1 << LRADC_RESOLUTION);
+	pressure /= m2;
+
+	dev_dbg(lradc->dev, "Pressure = %u\n", pressure);
+	return pressure;
+}
+
+#define TS_CH_XP 2
+#define TS_CH_YP 3
+#define TS_CH_XM 4
+#define TS_CH_YM 5
+
+static int mxs_lradc_read_ts_channel(struct mxs_lradc *lradc)
+{
+	u32 reg;
+	int val;
+
+	reg = readl(lradc->base + LRADC_CTRL1);
+
+	/* only channels 3 to 5 are of interest here */
+	if (reg & LRADC_CTRL1_LRADC_IRQ(TS_CH_YP)) {
+		mxs_lradc_reg_clear(lradc, LRADC_CTRL1_LRADC_IRQ_EN(TS_CH_YP) |
+			LRADC_CTRL1_LRADC_IRQ(TS_CH_YP), LRADC_CTRL1);
+		val = mxs_lradc_read_raw_channel(lradc, TS_CH_YP);
+	} else if (reg & LRADC_CTRL1_LRADC_IRQ(TS_CH_XM)) {
+		mxs_lradc_reg_clear(lradc, LRADC_CTRL1_LRADC_IRQ_EN(TS_CH_XM) |
+			LRADC_CTRL1_LRADC_IRQ(TS_CH_XM), LRADC_CTRL1);
+		val = mxs_lradc_read_raw_channel(lradc, TS_CH_XM);
+	} else if (reg & LRADC_CTRL1_LRADC_IRQ(TS_CH_YM)) {
+		mxs_lradc_reg_clear(lradc, LRADC_CTRL1_LRADC_IRQ_EN(TS_CH_YM) |
+			LRADC_CTRL1_LRADC_IRQ(TS_CH_YM), LRADC_CTRL1);
+		val = mxs_lradc_read_raw_channel(lradc, TS_CH_YM);
+	} else {
+		return -EIO;
+	}
+
+	mxs_lradc_reg(lradc, 0, LRADC_DELAY(2));
+	mxs_lradc_reg(lradc, 0, LRADC_DELAY(3));
+
+	return val;
+}
+
+/*
+ * YP(open)--+-------------+
+ *           |             |--+
+ *           |             |  |
+ *    YM(-)--+-------------+  |
+ *             +--------------+
+ *             |              |
+ *         XP(weak+)        XM(open)
+ *
+ * "weak+" means 200k Ohm VDDIO
+ * (-) means GND
+ */
+static void mxs_lradc_setup_touch_detection(struct mxs_lradc *lradc)
+{
+	/*
+	 * In order to detect a touch event the 'touch detect enable' bit
+	 * enables:
+	 *  - a weak pullup to the X+ connector
+	 *  - a strong ground at the Y- connector
+	 */
+	mxs_lradc_reg_clear(lradc, mxs_lradc_plate_mask(lradc), LRADC_CTRL0);
+	mxs_lradc_reg_set(lradc, mxs_lradc_touch_detect_bit(lradc),
+				LRADC_CTRL0);
+}
+
+/*
+ * YP(meas)--+-------------+
+ *           |             |--+
+ *           |             |  |
+ * YM(open)--+-------------+  |
+ *             +--------------+
+ *             |              |
+ *           XP(+)          XM(-)
+ *
+ * (+) means here 1.85 V
+ * (-) means here GND
+ */
+static void mxs_lradc_prepare_x_pos(struct mxs_lradc *lradc)
+{
+	mxs_lradc_reg_clear(lradc, mxs_lradc_plate_mask(lradc), LRADC_CTRL0);
+	mxs_lradc_reg_set(lradc, mxs_lradc_drive_x_plate(lradc), LRADC_CTRL0);
+
+	lradc->cur_plate = LRADC_SAMPLE_X;
+	mxs_lradc_setup_ts_channel(lradc, TS_CH_YP);
+}
+
+/*
+ *   YP(+)--+-------------+
+ *          |             |--+
+ *          |             |  |
+ *   YM(-)--+-------------+  |
+ *            +--------------+
+ *            |              |
+ *         XP(open)        XM(meas)
+ *
+ * (+) means here 1.85 V
+ * (-) means here GND
+ */
+static void mxs_lradc_prepare_y_pos(struct mxs_lradc *lradc)
+{
+	mxs_lradc_reg_clear(lradc, mxs_lradc_plate_mask(lradc), LRADC_CTRL0);
+	mxs_lradc_reg_set(lradc, mxs_lradc_drive_y_plate(lradc), LRADC_CTRL0);
+
+	lradc->cur_plate = LRADC_SAMPLE_Y;
+	mxs_lradc_setup_ts_channel(lradc, TS_CH_XM);
+}
+
+/*
+ *    YP(+)--+-------------+
+ *           |             |--+
+ *           |             |  |
+ * YM(meas)--+-------------+  |
+ *             +--------------+
+ *             |              |
+ *          XP(meas)        XM(-)
+ *
+ * (+) means here 1.85 V
+ * (-) means here GND
+ */
+static void mxs_lradc_prepare_pressure(struct mxs_lradc *lradc)
+{
+	mxs_lradc_reg_clear(lradc, mxs_lradc_plate_mask(lradc), LRADC_CTRL0);
+	mxs_lradc_reg_set(lradc, mxs_lradc_drive_pressure(lradc), LRADC_CTRL0);
+
+	lradc->cur_plate = LRADC_SAMPLE_PRESSURE;
+	mxs_lradc_setup_ts_pressure(lradc, TS_CH_XP, TS_CH_YM);
+}
+
+static void mxs_lradc_enable_touch_detection(struct mxs_lradc *lradc)
+{
+	mxs_lradc_setup_touch_detection(lradc);
+
+	lradc->cur_plate = LRADC_TOUCH;
+	mxs_lradc_reg_clear(lradc, LRADC_CTRL1_TOUCH_DETECT_IRQ |
+				LRADC_CTRL1_TOUCH_DETECT_IRQ_EN, LRADC_CTRL1);
+	mxs_lradc_reg_set(lradc, LRADC_CTRL1_TOUCH_DETECT_IRQ_EN, LRADC_CTRL1);
+}
+
+static void mxs_lradc_report_ts_event(struct mxs_lradc *lradc)
+{
+	input_report_abs(lradc->ts_input, ABS_X, lradc->ts_x_pos);
+	input_report_abs(lradc->ts_input, ABS_Y, lradc->ts_y_pos);
+	input_report_abs(lradc->ts_input, ABS_PRESSURE, lradc->ts_pressure);
+	input_report_key(lradc->ts_input, BTN_TOUCH, 1);
+	input_sync(lradc->ts_input);
+}
+
+static void mxs_lradc_complete_touch_event(struct mxs_lradc *lradc)
+{
+	mxs_lradc_setup_touch_detection(lradc);
+	lradc->cur_plate = LRADC_SAMPLE_VALID;
+	/*
+	 * start a dummy conversion to burn time to settle the signals
+	 * note: we are not interested in the conversion's value
+	 */
+	mxs_lradc_reg(lradc, 0, LRADC_CH(5));
+	mxs_lradc_reg_clear(lradc, LRADC_CTRL1_LRADC_IRQ(5), LRADC_CTRL1);
+	mxs_lradc_reg_set(lradc, LRADC_CTRL1_LRADC_IRQ_EN(5), LRADC_CTRL1);
+	mxs_lradc_reg(lradc, LRADC_DELAY_TRIGGER(1 << 5) |
+		LRADC_DELAY_KICK | LRADC_DELAY_DELAY(10), /* waste 5 ms */
+			LRADC_DELAY(2));
+}
+
+/*
+ * in order to avoid false measurements, report only samples where
+ * the surface is still touched after the position measurement
+ */
+static void mxs_lradc_finish_touch_event(struct mxs_lradc *lradc, bool valid)
+{
+	/* if it is still touched, report the sample */
+	if (valid && mxs_lradc_check_touch_event(lradc)) {
+		lradc->ts_valid = true;
+		mxs_lradc_report_ts_event(lradc);
+	}
+
+	/* if it is even still touched, continue with the next measurement */
+	if (mxs_lradc_check_touch_event(lradc)) {
+		mxs_lradc_prepare_y_pos(lradc);
+		return;
+	}
+
+	if (lradc->ts_valid) {
+		/* signal the release */
+		lradc->ts_valid = false;
+		input_report_key(lradc->ts_input, BTN_TOUCH, 0);
+		input_sync(lradc->ts_input);
+	}
+
+	/* if it is released, wait for the next touch via IRQ */
+	mxs_lradc_reg_clear(lradc, LRADC_CTRL1_TOUCH_DETECT_IRQ, LRADC_CTRL1);
+	mxs_lradc_reg_set(lradc, LRADC_CTRL1_TOUCH_DETECT_IRQ_EN, LRADC_CTRL1);
+}
+
+/* touchscreen's state machine */
+static void mxs_lradc_handle_touch(struct mxs_lradc *lradc)
+{
+	int val;
+
+	switch (lradc->cur_plate) {
+	case LRADC_TOUCH:
+		/*
+		 * start with the Y-pos, because it uses nearly the same plate
+		 * settings like the touch detection
+		 */
+		if (mxs_lradc_check_touch_event(lradc)) {
+			mxs_lradc_reg_clear(lradc,
+					LRADC_CTRL1_TOUCH_DETECT_IRQ_EN,
+					LRADC_CTRL1);
+			mxs_lradc_prepare_y_pos(lradc);
+		}
+		mxs_lradc_reg_clear(lradc, LRADC_CTRL1_TOUCH_DETECT_IRQ,
+					LRADC_CTRL1);
+		return;
+
+	case LRADC_SAMPLE_Y:
+		val = mxs_lradc_read_ts_channel(lradc);
+		if (val < 0) {
+			mxs_lradc_enable_touch_detection(lradc); /* re-start */
+			return;
+		}
+		lradc->ts_y_pos = val;
+		mxs_lradc_prepare_x_pos(lradc);
+		return;
+
+	case LRADC_SAMPLE_X:
+		val = mxs_lradc_read_ts_channel(lradc);
+		if (val < 0) {
+			mxs_lradc_enable_touch_detection(lradc); /* re-start */
+			return;
+		}
+		lradc->ts_x_pos = val;
+		mxs_lradc_prepare_pressure(lradc);
+		return;
+
+	case LRADC_SAMPLE_PRESSURE:
+		lradc->ts_pressure =
+			mxs_lradc_read_ts_pressure(lradc, TS_CH_XP, TS_CH_YM);
+		mxs_lradc_complete_touch_event(lradc);
+		return;
+
+	case LRADC_SAMPLE_VALID:
+		val = mxs_lradc_read_ts_channel(lradc); /* ignore the value */
+		mxs_lradc_finish_touch_event(lradc, 1);
+		break;
+	}
+}
+
 /*
  * Raw I/O operations
  */
@@ -385,15 +820,6 @@ static const struct iio_info mxs_lradc_iio_info = {
 	.read_raw		= mxs_lradc_read_raw,
 };
 
-/*
- * Touchscreen handling
- */
-enum lradc_ts_plate {
-	LRADC_SAMPLE_X,
-	LRADC_SAMPLE_Y,
-	LRADC_SAMPLE_PRESSURE,
-};
-
 static int mxs_lradc_ts_touched(struct mxs_lradc *lradc)
 {
 	uint32_t reg;
@@ -551,10 +977,6 @@ static void mxs_lradc_ts_work(struct work_struct *ts_work)
 	input_report_key(lradc->ts_input, BTN_TOUCH, 0);
 	input_sync(lradc->ts_input);
 
-	/* Do not restart the TS IRQ if the driver is shutting down. */
-	if (lradc->stop_touchscreen)
-		return;
-
 	/* Restart the touchscreen interrupts. */
 	mxs_lradc_reg_clear(lradc, LRADC_CTRL1_TOUCH_DETECT_IRQ, LRADC_CTRL1);
 	mxs_lradc_reg_set(lradc, LRADC_CTRL1_TOUCH_DETECT_IRQ_EN, LRADC_CTRL1);
@@ -564,36 +986,29 @@ static int mxs_lradc_ts_open(struct input_dev *dev)
 {
 	struct mxs_lradc *lradc = input_get_drvdata(dev);
 
-	/* The touchscreen is starting. */
-	lradc->stop_touchscreen = false;
-
 	/* Enable the touch-detect circuitry. */
-	mxs_lradc_reg_set(lradc, mxs_lradc_touch_detect_bit(lradc),
-						LRADC_CTRL0);
-
-	/* Enable the touch-detect IRQ. */
-	mxs_lradc_reg_set(lradc, LRADC_CTRL1_TOUCH_DETECT_IRQ_EN, LRADC_CTRL1);
+	mxs_lradc_enable_touch_detection(lradc);
 
 	return 0;
 }
 
-static void mxs_lradc_ts_close(struct input_dev *dev)
+static void mxs_lradc_disable_ts(struct mxs_lradc *lradc)
 {
-	struct mxs_lradc *lradc = input_get_drvdata(dev);
-
-	/* Indicate the touchscreen is stopping. */
-	lradc->stop_touchscreen = true;
-	mb();
+	/* stop all interrupts from firing */
+	mxs_lradc_reg_clear(lradc, LRADC_CTRL1_TOUCH_DETECT_IRQ_EN |
+		LRADC_CTRL1_LRADC_IRQ_EN(2) | LRADC_CTRL1_LRADC_IRQ_EN(3) |
+		LRADC_CTRL1_LRADC_IRQ_EN(4) | LRADC_CTRL1_LRADC_IRQ_EN(5),
+		LRADC_CTRL1);
 
-	/* Wait until touchscreen thread finishes any possible remnants. */
-	cancel_work_sync(&lradc->ts_work);
+	/* Power-down touchscreen touch-detect circuitry. */
+	mxs_lradc_reg_clear(lradc, mxs_lradc_plate_mask(lradc), LRADC_CTRL0);
+}
 
-	/* Disable touchscreen touch-detect IRQ. */
-	mxs_lradc_reg_clear(lradc, LRADC_CTRL1_TOUCH_DETECT_IRQ_EN,
-						LRADC_CTRL1);
+static void mxs_lradc_ts_close(struct input_dev *dev)
+{
+	struct mxs_lradc *lradc = input_get_drvdata(dev);
 
-	/* Power-down touchscreen touch-detect circuitry. */
-	mxs_lradc_reg_clear(lradc, mxs_lradc_touch_detect_bit(lradc), LRADC_CTRL0);
+	mxs_lradc_disable_ts(lradc);
 }
 
 static int mxs_lradc_ts_register(struct mxs_lradc *lradc)
@@ -641,6 +1056,7 @@ static void mxs_lradc_ts_unregister(struct mxs_lradc *lradc)
 
 	cancel_work_sync(&lradc->ts_work);
 
+	mxs_lradc_disable_ts(lradc);
 	input_unregister_device(lradc->ts_input);
 }
 
@@ -653,30 +1069,23 @@ static irqreturn_t mxs_lradc_handle_irq(int irq, void *data)
 	struct mxs_lradc *lradc = iio_priv(iio);
 	unsigned long reg = readl(lradc->base + LRADC_CTRL1);
 	const uint32_t ts_irq_mask =
-		LRADC_CTRL1_TOUCH_DETECT_IRQ_EN |
-		LRADC_CTRL1_TOUCH_DETECT_IRQ;
+		LRADC_CTRL1_TOUCH_DETECT_IRQ |
+		LRADC_CTRL1_LRADC_IRQ(2) |
+		LRADC_CTRL1_LRADC_IRQ(3) |
+		LRADC_CTRL1_LRADC_IRQ(4) |
+		LRADC_CTRL1_LRADC_IRQ(5);
 
 	if (!(reg & mxs_lradc_irq_mask(lradc)))
 		return IRQ_NONE;
 
-	/*
-	 * Touchscreen IRQ handling code has priority and therefore
-	 * is placed here. In case touchscreen IRQ arrives, disable
-	 * it ASAP
-	 */
-	if (reg & LRADC_CTRL1_TOUCH_DETECT_IRQ) {
-		mxs_lradc_reg_clear(lradc, ts_irq_mask, LRADC_CTRL1);
-		if (!lradc->stop_touchscreen)
-			schedule_work(&lradc->ts_work);
-	}
+	if (lradc->use_touchscreen && (reg & ts_irq_mask))
+		mxs_lradc_handle_touch(lradc);
 
 	if (iio_buffer_enabled(iio))
 		iio_trigger_poll(iio->trig, iio_get_time_ns());
 	else if (reg & LRADC_CTRL1_LRADC_IRQ(0))
 		complete(&lradc->completion);
 
-	mxs_lradc_reg_clear(lradc, reg & mxs_lradc_irq_mask(lradc), LRADC_CTRL1);
-
 	return IRQ_HANDLED;
 }
 
@@ -971,6 +1380,17 @@ static const struct of_device_id mxs_lradc_dt_ids[] = {
 };
 MODULE_DEVICE_TABLE(of, mxs_lradc_dt_ids);
 
+static int mxs_lradc_probe_touchscreen(struct mxs_lradc *lradc,
+						struct device_node *lradc_node)
+{
+	/* TODO retrieve from device tree */
+	lradc->over_sample_cnt = 4;
+	lradc->over_sample_delay = 2;
+	lradc->settling_delay = 10;
+
+	return 0;
+}
+
 static int mxs_lradc_probe(struct platform_device *pdev)
 {
 	const struct of_device_id *of_id =
@@ -983,7 +1403,7 @@ static int mxs_lradc_probe(struct platform_device *pdev)
 	struct iio_dev *iio;
 	struct resource *iores;
 	uint32_t ts_wires = 0;
-	int ret = 0;
+	int ret = 0, touch_ret;
 	int i;
 
 	/* Allocate the IIO device. */
@@ -1003,7 +1423,7 @@ static int mxs_lradc_probe(struct platform_device *pdev)
 	if (IS_ERR(lradc->base))
 		return PTR_ERR(lradc->base);
 
-	INIT_WORK(&lradc->ts_work, mxs_lradc_ts_work);
+	touch_ret = mxs_lradc_probe_touchscreen(lradc, node);
 
 	/* Check if touchscreen is enabled in DT. */
 	ret = of_property_read_u32(node, "fsl,lradc-touchscreen-wires",
@@ -1066,9 +1486,11 @@ static int mxs_lradc_probe(struct platform_device *pdev)
 		goto err_dev;
 
 	/* Register the touchscreen input device. */
-	ret = mxs_lradc_ts_register(lradc);
-	if (ret)
-		goto err_dev;
+	if (touch_ret == 0) {
+		ret = mxs_lradc_ts_register(lradc);
+		if (ret)
+			goto err_dev;
+	}
 
 	/* Register IIO device. */
 	ret = iio_device_register(iio);
maintainer
#15 lore raw

PATCH 5/6 Staging/iio/adc/touchscreen/MXS: add interrupt driven touch detection

Quoted 15 lines · Jonathan Cameron
Quoted 6 lines · Juergen Beisert

For battery driven systems it is a very bad idea to collect the touchscreen data within a kernel busy loop.

This change uses the features of the hardware to delay and accumulate samples in hardware to avoid a high interrupt and CPU load.

Quoted 8 lines

Note: this is only tested on an i.MX23 SoC yet.

Quoted 5 lines

While this driver is placed in IIO within staging at the moment, these changes are definitely input related. Hence I have cc'd Dmitry and the input list.

I am personaly a little uncomfortable that we have such a complex bit of input code sat within an IIO driver but such is life.

The logic in here looks reasonable to me. I am far from a specialist in how these touch screens are normally handled though.

One thing to note is that you really want to get a proposed device tree spec out asap as that can take longer to review than the driver. If you are proposing to do that as a future patch, then take into account that you'll need to ensure these are the defaults if it is not specified in the device tree for ever more (which is more painful than hammering out he device tree stuff now!)
...

Quoted 11 lines
Quoted 11 lines
drivers/staging/iio/adc/mxs-lradc.c +11 -0
+static int mxs_lradc_probe_touchscreen(struct mxs_lradc *lradc,
+						struct device_node *lradc_node)
+{
+	/* TODO retrieve from device tree */
+	lradc->over_sample_cnt = 4;
+	lradc->over_sample_delay = 2;
+	lradc->settling_delay = 10;
+
+	return 0;
+}
+

...

#16 lore raw

PATCH 5/6 Staging/iio/adc/touchscreen/MXS: add interrupt driven touch detection

Hi Jonathan,

Quoted 27 lines · On Sunday 15 September 2013 18:10:18 Jonathan Cameron wrote:
Quoted 16 lines · Jonathan Cameron
Quoted 6 lines · Juergen Beisert

For battery driven systems it is a very bad idea to collect the touchscreen data within a kernel busy loop.

This change uses the features of the hardware to delay and accumulate samples in hardware to avoid a high interrupt and CPU load.

Quoted 8 lines

Note: this is only tested on an i.MX23 SoC yet.

CC linux-arm-kernel at lists.infradead.org
CC devel at driverdev.osuosl.org
CC Marek Vasut <[email protected]>
CC Fabio Estevam <[email protected]>
CC Jonathan Cameron <[email protected]>
Quoted 6 lines

While this driver is placed in IIO within staging at the moment, these changes are definitely input related. Hence I have cc'd Dmitry and the input list.

I am personaly a little uncomfortable that we have such a complex bit of input code sat within an IIO driver but such is life.

The logic in here looks reasonable to me. I am far from a specialist in how these touch screens are normally handled though.

Quoted 7 lines

One thing to note is that you really want to get a proposed device tree spec out asap as that can take longer to review than the driver. If you are proposing to do that as a future patch, then take into account that you'll need to ensure these are the defaults if it is not specified in the device tree for ever more (which is more painful than hammering out he device tree stuff now!)
...

Will do.

Regards,
Juergen

Signature · 2 lines
Pengutronix e.K. ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?| Juergen Beisert ? ? ? ? ? ? |
Linux Solutions for Science and Industry ? ? ?| http://www.pengutronix.de/  |
#17 lore raw

PATCH 5/6 Staging/iio/adc/touchscreen/MXS: add interrupt driven touch detection

In reply to Jonathan Cameron

Hi Jonathan,

Quoted 16 lines · On Sunday 15 September 2013 12:56:25 Jonathan Cameron wrote:
Quoted 6 lines · Juergen Beisert

For battery driven systems it is a very bad idea to collect the touchscreen data within a kernel busy loop.

This change uses the features of the hardware to delay and accumulate samples in hardware to avoid a high interrupt and CPU load.

Quoted 8 lines

Note: this is only tested on an i.MX23 SoC yet.

CC linux-arm-kernel at lists.infradead.org
CC devel at driverdev.osuosl.org
CC Marek Vasut <[email protected]>
CC Fabio Estevam <[email protected]>
CC Jonathan Cameron <[email protected]>
Quoted 6 lines

While this driver is placed in IIO within staging at the moment, these changes are definitely input related. Hence I have cc'd Dmitry and the input list.

I am personaly a little uncomfortable that we have such a complex bit of input code sat within an IIO driver but such is life.

Maybe an MFD for this ADC unit would be a better way to go? Currently I have a different problem with this driver, because the ADC unit monitors the battery as well. And the charging driver from the power subsystem needs these values to charge the battery in a correct manner.

Quoted 1 line

[...]

Regards,
Juergen

Signature · 2 lines
Pengutronix e.K. ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?| Juergen Beisert ? ? ? ? ? ? |
Linux Solutions for Science and Industry ? ? ?| http://www.pengutronix.de/  |
#18 lore raw

PATCH 5/6 Staging/iio/adc/touchscreen/MXS: add interrupt driven touch detection

Hi Jonathan,

Quoted 5 lines · On Monday 16 September 2013 10:10:22 Jürgen Beisert wrote:

[...]

Quoted 4 lines

While this driver is placed in IIO within staging at the moment, these changes are definitely input related. Hence I have cc'd Dmitry and the input list.

Quoted 7 lines
Quoted 2 lines

I am personaly a little uncomfortable that we have such a complex bit of input code sat within an IIO driver but such is life.

Maybe an MFD for this ADC unit would be a better way to go? Currently I have a different problem with this driver, because the ADC unit monitors the battery as well. And the charging driver from the power subsystem needs these values to charge the battery in a correct manner.

I would suggest:

drivers/staging/iio/TODO +11 -0
index 04c2326..c22a0ed 100644
@@ -13,6 +13,17 @@ Would be nice
 3) Expand device set. Lots of other maxim adc's have very
    similar interfaces.
 
+MXS LRADC driver:
+This is a classic MFD device as it combines the following subdevices
+ - touchscreen controller (input subsystem related device)
+ - general purpose ADC channels
+ - battery voltage monitor (power subsystem related device)
+ - die temperature monitor (thermal management)
+
+At least the battery voltage and die temperature feature is required in-kernel
+by a driver of the SoC's battery charging unit to avoid any damage to the
+silicon and the battery.
+
 TSL2561
 Would be nice
 1) Open question of userspace vs kernel space balance when

Regards,
Juergen

Signature · 2 lines
Pengutronix e.K.                              | Juergen Beisert             |
Linux Solutions for Science and Industry      | http://www.pengutronix.de/  |
#19 lore raw

PATCH 5/6 Staging/iio/adc/touchscreen/MXS: add interrupt driven touch detection

In reply to Jürgen Beisert

Dear J?rgen Beisert,

Quoted 23 lines

Hi Jonathan,

Quoted 20 lines · On Sunday 15 September 2013 12:56:25 Jonathan Cameron wrote:
Quoted 6 lines · Juergen Beisert

For battery driven systems it is a very bad idea to collect the touchscreen data within a kernel busy loop.

This change uses the features of the hardware to delay and accumulate samples in hardware to avoid a high interrupt and CPU load.

Quoted 8 lines

Note: this is only tested on an i.MX23 SoC yet.

CC linux-arm-kernel at lists.infradead.org
CC devel at driverdev.osuosl.org
CC Marek Vasut <[email protected]>
CC Fabio Estevam <[email protected]>
CC Jonathan Cameron <[email protected]>

While this driver is placed in IIO within staging at the moment, these changes are definitely input related. Hence I have cc'd Dmitry and the input list.

Quoted 7 lines
Quoted 2 lines

I am personaly a little uncomfortable that we have such a complex bit of input code sat within an IIO driver but such is life.

Maybe an MFD for this ADC unit would be a better way to go? Currently I have a different problem with this driver, because the ADC unit monitors the battery as well. And the charging driver from the power subsystem needs these values to charge the battery in a correct manner.

Are you planning to post the power block patches too ?

Best regards,
Marek Vasut

#20 lore raw

PATCH 5/6 Staging/iio/adc/touchscreen/MXS: add interrupt driven touch detection

Hi Marek,

Quoted 24 lines · On Monday 16 September 2013 16:23:48 Marek Vasut wrote:
Quoted 24 lines · On Sunday 15 September 2013 12:56:25 Jonathan Cameron wrote:
Quoted 22 lines · Juergen Beisert
Quoted 6 lines

For battery driven systems it is a very bad idea to collect the touchscreen data within a kernel busy loop.

This change uses the features of the hardware to delay and accumulate samples in hardware to avoid a high interrupt and CPU load.

Quoted 8 lines

Note: this is only tested on an i.MX23 SoC yet.

While this driver is placed in IIO within staging at the moment, these changes are definitely input related. Hence I have cc'd Dmitry and the input list.

I am personaly a little uncomfortable that we have such a complex bit of input code sat within an IIO driver but such is life.

Quoted 6 lines
Quoted 4 lines

Maybe an MFD for this ADC unit would be a better way to go? Currently I have a different problem with this driver, because the ADC unit monitors the battery as well. And the charging driver from the power subsystem needs these values to charge the battery in a correct manner.

Are you planning to post the power block patches too ?

When they will work: yes. Currently it crashes all the time. The PMIC is a beast...

Regards,
Juergen

Signature · 2 lines
Pengutronix e.K.                              | Juergen Beisert             |
Linux Solutions for Science and Industry      | http://www.pengutronix.de/  |
#21 lore raw

PATCH 5/6 Staging/iio/adc/touchscreen/MXS: add interrupt driven touch detection

Dear J?rgen Beisert,

Quoted 34 lines

Hi Marek,

Quoted 31 lines · On Monday 16 September 2013 16:23:48 Marek Vasut wrote:
Quoted 30 lines · On Sunday 15 September 2013 12:56:25 Jonathan Cameron wrote:
Quoted 17 lines · Juergen Beisert
Quoted 7 lines

For battery driven systems it is a very bad idea to collect the touchscreen data within a kernel busy loop.

This change uses the features of the hardware to delay and accumulate samples in hardware to avoid a high interrupt and CPU load.

Quoted 8 lines

Note: this is only tested on an i.MX23 SoC yet.

CC linux-arm-kernel at lists.infradead.org
CC devel at driverdev.osuosl.org
CC Marek Vasut <[email protected]>
CC Fabio Estevam <[email protected]>
CC Jonathan Cameron <[email protected]>
Quoted 6 lines

While this driver is placed in IIO within staging at the moment, these changes are definitely input related. Hence I have cc'd Dmitry and the input list.

I am personaly a little uncomfortable that we have such a complex bit of input code sat within an IIO driver but such is life.

Maybe an MFD for this ADC unit would be a better way to go? Currently I have a different problem with this driver, because the ADC unit monitors the battery as well. And the charging driver from the power subsystem needs these values to charge the battery in a correct manner.

Quoted 4 lines
Quoted 1 line

Are you planning to post the power block patches too ?

When they will work: yes. Currently it crashes all the time. The PMIC is a beast...

Full ACK

Best regards,
Marek Vasut

maintainer
#22 lore raw

PATCH 5/6 Staging/iio/adc/touchscreen/MXS: add interrupt driven touch detection

In reply to Jürgen Beisert
Quoted 23 lines · J?rgen Beisert

Hi Jonathan,

Quoted 5 lines · On Sunday 15 September 2013 12:56:25 Jonathan Cameron wrote:
Quoted 4 lines · Juergen Beisert

For battery driven systems it is a very bad idea to collect the touchscreen data within a kernel busy loop.

This change uses the features of the hardware to delay and

accumulate

Quoted 4 lines
Quoted 4 lines

samples in hardware to avoid a high interrupt and CPU load.

Note: this is only tested on an i.MX23 SoC yet.

Quoted 8 lines
Quoted 6 lines
CC linux-arm-kernel at lists.infradead.org
CC devel at driverdev.osuosl.org
CC Marek Vasut <[email protected]>
CC Fabio Estevam <[email protected]>
CC Jonathan Cameron <[email protected]>

While this driver is placed in IIO within staging at the moment,

these

Quoted 1 line

changes are definitely input related. Hence I have cc'd Dmitry and

Quoted 8 lines

the

Quoted 3 lines

input list.

I am personaly a little uncomfortable that we have such a complex bit

of

Quoted 1 line

input code sat within an IIO driver but such is life.

Maybe an MFD for this ADC unit would be a better way to go?

That would be great and is definitely the preferred method.

Currently I

Quoted 6 lines

have a
different problem with this driver, because the ADC unit monitors the battery
as well. And the charging driver from the power subsystem needs these values
to charge the battery in a correct manner.

There is an iio client battery driver as generic_ADC_battery.c but it is currently only doing polled access. Not too hard to add buffered access though ideally we would want a generic way of combining consumers doing polled and interrupt driven accesses.

Quoted 5 lines
Quoted 2 lines

[...]

Regards,
Juergen

Signature · 1 line
Sent from my Android phone with K-9 Mail. Please excuse my brevity.
#23 lore raw

PATCH 5/6 Staging/iio/adc/touchscreen/MXS: add interrupt driven touch detection

Hi Jonathan,

Quoted 21 lines · On Monday 16 September 2013 17:30:32 Jonathan Cameron wrote:
Quoted 21 lines · On Sunday 15 September 2013 12:56:25 Jonathan Cameron wrote:
Quoted 20 lines · Juergen Beisert
Quoted 6 lines

For battery driven systems it is a very bad idea to collect the touchscreen data within a kernel busy loop.

This change uses the features of the hardware to delay and accumulate samples in hardware to avoid a high interrupt and CPU load.

Quoted 8 lines

Note: this is only tested on an i.MX23 SoC yet.

CC linux-arm-kernel at lists.infradead.org
CC devel at driverdev.osuosl.org
CC Marek Vasut <[email protected]>
CC Fabio Estevam <[email protected]>
CC Jonathan Cameron <[email protected]>

While this driver is placed in IIO within staging at the moment, these changes are definitely input related. Hence I have cc'd Dmitry and the input list.

Quoted 6 lines
Quoted 4 lines
Quoted 2 lines

I am personaly a little uncomfortable that we have such a complex bit of input code sat within an IIO driver but such is life.

Maybe an MFD for this ADC unit would be a better way to go?

That would be great and is definitely the preferred method.

Cannot continue to convert the driver into an MFD device. The project does not give me the time to do so.

Regards,
Juergen

Signature · 2 lines
Pengutronix e.K. ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?| Juergen Beisert ? ? ? ? ? ? |
Linux Solutions for Science and Industry ? ? ?| http://www.pengutronix.de/  |
maintainer
#24 lore raw

PATCH 5/6 Staging/iio/adc/touchscreen/MXS: add interrupt driven touch detection

.

Quoted 32 lines · J?rgen Beisert

Hi Jonathan,

Quoted 7 lines · On Monday 16 September 2013 17:30:32 Jonathan Cameron wrote:
Quoted 7 lines · On Sunday 15 September 2013 12:56:25 Jonathan ,,, wrote:
Quoted 6 lines · Juergen Beisert
Quoted 5 lines

For battery driven systems it is a very bad idea to collect the touchscreen data within a kernel busy loop.

This change uses the features of the hardware to delay and accumulate samples in hardware to avoid a high interrupt and CPU

load.

Quoted 10 lines
Quoted 10 lines
Quoted 10 lines
Quoted 9 lines

Note: this is only tested on an i.MX23 SoC yet.

CC linux-arm-kernel at lists.infradead.org
CC devel at driverdev.osuosl.org
CC Marek Vasut <[email protected]>
CC Fabio Estevam <[email protected]>
CC Jonathan Cameron <[email protected]>
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines

While this driver is placed in IIO within staging at the moment, these changes are definitely input related. Hence I have cc'd

Dmitry and

Quoted 3 lines
Quoted 3 lines
Quoted 3 lines

the input list.

I am personaly a little uncomfortable that we have such a complex

bit

Quoted 4 lines
Quoted 3 lines
Quoted 1 line

of input code sat within an IIO driver but such is life.

Maybe an MFD for this ADC unit would be a better way to go?

Quoted 8 lines
Quoted 1 line

That would be great and is definitely the preferred method.

Cannot continue to convert the driver into an MFD device. The project does not
give me the time to do so.

Regards,
Juergen

Fair enough. Perhaps someone else will pick up the gauntlet :) The old call of why there isn't enough time in the day!

Signature · 1 line
Sent from my Android phone with K-9 Mail. Please excuse my brevity.
#25 lore raw

PATCH 5/6 Staging/iio/adc/touchscreen/MXS: add interrupt driven touch detection

In reply to Jonathan Cameron
Quoted 21 lines · Jonathan Cameron
Quoted 6 lines · Juergen Beisert

For battery driven systems it is a very bad idea to collect the touchscreen data within a kernel busy loop.

This change uses the features of the hardware to delay and accumulate samples in hardware to avoid a high interrupt and CPU load.

Quoted 8 lines

Note: this is only tested on an i.MX23 SoC yet.

CC linux-arm-kernel at lists.infradead.org
CC devel at driverdev.osuosl.org
CC Marek Vasut <[email protected]>
CC Fabio Estevam <[email protected]>
CC Jonathan Cameron <[email protected]>

While this driver is placed in IIO within staging at the moment, these changes are definitely input related. Hence I have cc'd Dmitry and the input list.

I am personaly a little uncomfortable that we have such a complex bit of input code sat within an IIO driver but such is life.

...

Quoted 9 lines

drivers/staging/iio/adc/mxs-lradc.c static void mxs_lradc_ts_unregister(struct mxs_lradc *lradc) · line 1061

Quoted 9 lines

static int mxs_lradc_ts_register(struct mxs_lradc *lradc)

drivers/staging/iio/adc/mxs-lradc.c +1 -0
@@ -641,6 +1056,7 @@ static void mxs_lradc_ts_unregister(struct mxs_lradc *lradc)
 
 	cancel_work_sync(&lradc->ts_work);
 
+	mxs_lradc_disable_ts(lradc);
 	input_unregister_device(lradc->ts_input);
 }

This looks iffy... Normally you disable the device so that it does not generate more interrupts, and then cancel outstanding work(s), otherwise newly generated interrupts may cause more work to be scheduled. Or I missed some of the context and this is not a concern here?

Thanks.

Signature · 1 line
Dmitry
#26 lore raw

PATCH 5/6 Staging/iio/adc/touchscreen/MXS: add interrupt driven touch detection

Hi Dmitry,

Quoted 7 lines · On Monday 16 September 2013 17:28:46 Dmitry Torokhov wrote:

[...]

Quoted 6 lines
Quoted 6 lines

static int mxs_lradc_ts_register(struct mxs_lradc *lradc)

drivers/staging/iio/adc/mxs-lradc.c +0 -0
@@ -641,6 +1056,7 @@ static void mxs_lradc_ts_unregister(struct
 mxs_lradc *lradc)
 
 	cancel_work_sync(&lradc->ts_work);
 
Quoted 8 lines
Quoted 3 lines

drivers/staging/iio/adc/mxs-lradc.c static void mxs_lradc_ts_unregister(struct mxs_lradc *lradc) · line 1061

Quoted 3 lines
drivers/staging/iio/adc/mxs-lradc.c +1 -0
+	mxs_lradc_disable_ts(lradc);
 	input_unregister_device(lradc->ts_input);
 }

This looks iffy... Normally you disable the device so that it does not generate more interrupts, and then cancel outstanding work(s), otherwise newly generated interrupts may cause more work to be scheduled. Or I missed some of the context and this is not a concern here?

This part gets removed in patch 6/6:

@@ -1054,8 +891,6 @@ static void mxs_lradc_ts_unregister(struct mxs_lradc *lradc) if (!lradc->use_touchscreen)
                return;

-       cancel_work_sync(&lradc->ts_work);
-
        mxs_lradc_disable_ts(lradc); input_unregister_device(lradc->ts_input);
 }

But you are right, I should move this into patch 5/6.

Thanks

Regards,
Juergen

Signature · 2 lines
Pengutronix e.K.                              | Juergen Beisert             |
Linux Solutions for Science and Industry      | http://www.pengutronix.de/  |
#27 lore raw

PATCH 6/6 Staging/iio/adc/touchscreen/MXS: Remove old touchscreen detection implementation

In reply to Juergen Beisert
CC linux-arm-kernel at lists.infradead.org
CC devel at driverdev.osuosl.org
CC Marek Vasut <[email protected]>
CC Fabio Estevam <[email protected]>
CC Jonathan Cameron <[email protected]>
---
 drivers/staging/iio/adc/mxs-lradc.c | 165 ------------------------------------
 1 file changed, 165 deletions(-)
drivers/staging/iio/adc/mxs-lradc.c +0 -165
index 185f068..cb791c8 100644
@@ -183,7 +183,6 @@ struct mxs_lradc {
 	bool			use_touchbutton;
 
 	struct input_dev	*ts_input;
-	struct work_struct	ts_work;
 
 	enum mxs_lradc_id	soc;
 	enum lradc_ts_plate	cur_plate; /* statemachine */
@@ -820,168 +819,6 @@ static const struct iio_info mxs_lradc_iio_info = {
 	.read_raw		= mxs_lradc_read_raw,
 };
 
-static int mxs_lradc_ts_touched(struct mxs_lradc *lradc)
-{
-	uint32_t reg;
-
-	/* Enable touch detection. */
-	mxs_lradc_reg_clear(lradc, mxs_lradc_plate_mask(lradc), LRADC_CTRL0);
-	mxs_lradc_reg_set(lradc, mxs_lradc_touch_detect_bit(lradc),
-								LRADC_CTRL0);
-
-	msleep(LRADC_TS_SAMPLE_DELAY_MS);
-
-	reg = readl(lradc->base + LRADC_STATUS);
-
-	return reg & LRADC_STATUS_TOUCH_DETECT_RAW;
-}
-
-static int32_t mxs_lradc_ts_sample(struct mxs_lradc *lradc,
-				enum lradc_ts_plate plate, int change)
-{
-	unsigned long delay, jiff;
-	uint32_t reg, ctrl0 = 0, chan = 0;
-	/* The touchscreen always uses CTRL4 slot #7. */
-	const uint8_t slot = 7;
-	uint32_t val;
-
-	/*
-	 * There are three correct configurations of the controller sampling
-	 * the touchscreen, each of these configuration provides different
-	 * information from the touchscreen.
-	 *
-	 * The following table describes the sampling configurations:
-	 * +-------------+-------+-------+-------+
-	 * | Wire \ Axis |   X   |   Y   |   Z   |
-	 * +---------------------+-------+-------+
-	 * |   X+ (CH2)  |   HI  |   TS  |   TS  |
-	 * +-------------+-------+-------+-------+
-	 * |   X- (CH4)  |   LO  |   SH  |   HI  |
-	 * +-------------+-------+-------+-------+
-	 * |   Y+ (CH3)  |   SH  |   HI  |   HI  |
-	 * +-------------+-------+-------+-------+
-	 * |   Y- (CH5)  |   TS  |   LO  |   SH  |
-	 * +-------------+-------+-------+-------+
-	 *
-	 * HI ... strong '1'  ; LO ... strong '0'
-	 * SH ... sample here ; TS ... tri-state
-	 *
-	 * There are a few other ways of obtaining the Z coordinate
-	 * (aka. pressure), but the one in the table seems to be the
-	 * most reliable one.
-	 */
-	switch (plate) {
-	case LRADC_SAMPLE_X:
-		ctrl0 = mxs_lradc_drive_x_plate(lradc);
-		chan = 3;
-		break;
-	case LRADC_SAMPLE_Y:
-		ctrl0 = mxs_lradc_drive_y_plate(lradc);
-		chan = 4;
-		break;
-	case LRADC_SAMPLE_PRESSURE:
-		ctrl0 = mxs_lradc_drive_pressure(lradc);
-		chan = 5;
-		break;
-	}
-
-	if (change) {
-		mxs_lradc_reg_clear(lradc, mxs_lradc_plate_mask(lradc),
-						LRADC_CTRL0);
-		mxs_lradc_reg_set(lradc, ctrl0, LRADC_CTRL0);
-
-		mxs_lradc_reg_clear(lradc, LRADC_CTRL4_LRADCSELECT_MASK(slot),
-						LRADC_CTRL4);
-		mxs_lradc_reg_set(lradc,
-				chan << LRADC_CTRL4_LRADCSELECT_OFFSET(slot),
-				LRADC_CTRL4);
-	}
-
-	mxs_lradc_reg_clear(lradc, 0xffffffff, LRADC_CH(slot));
-	mxs_lradc_reg_set(lradc, 1 << slot, LRADC_CTRL0);
-
-	delay = jiffies + msecs_to_jiffies(LRADC_TS_SAMPLE_DELAY_MS);
-	do {
-		jiff = jiffies;
-		reg = readl_relaxed(lradc->base + LRADC_CTRL1);
-		if (reg & LRADC_CTRL1_LRADC_IRQ(slot))
-			break;
-	} while (time_before(jiff, delay));
-
-	mxs_lradc_reg_clear(lradc, LRADC_CTRL1_LRADC_IRQ(slot), LRADC_CTRL1);
-
-	if (time_after_eq(jiff, delay))
-		return -ETIMEDOUT;
-
-	val = readl(lradc->base + LRADC_CH(slot));
-	val &= LRADC_CH_VALUE_MASK;
-
-	return val;
-}
-
-static int32_t mxs_lradc_ts_sample_filter(struct mxs_lradc *lradc,
-				enum lradc_ts_plate plate)
-{
-	int32_t val, tot = 0;
-	int i;
-
-	val = mxs_lradc_ts_sample(lradc, plate, 1);
-
-	/* Delay a bit so the touchscreen is stable. */
-	mdelay(2);
-
-	for (i = 0; i < LRADC_TS_SAMPLE_AMOUNT; i++) {
-		val = mxs_lradc_ts_sample(lradc, plate, 0);
-		tot += val;
-	}
-
-	return tot / LRADC_TS_SAMPLE_AMOUNT;
-}
-
-static void mxs_lradc_ts_work(struct work_struct *ts_work)
-{
-	struct mxs_lradc *lradc = container_of(ts_work,
-				struct mxs_lradc, ts_work);
-	int val_x, val_y, val_p;
-	bool valid = false;
-
-	while (mxs_lradc_ts_touched(lradc)) {
-		/* Disable touch detector so we can sample the touchscreen. */
-		mxs_lradc_reg_clear(lradc, mxs_lradc_touch_detect_bit(lradc),
-						LRADC_CTRL0);
-
-		if (likely(valid)) {
-			input_report_abs(lradc->ts_input, ABS_X, val_x);
-			input_report_abs(lradc->ts_input, ABS_Y, val_y);
-			input_report_abs(lradc->ts_input, ABS_PRESSURE, val_p);
-			input_report_key(lradc->ts_input, BTN_TOUCH, 1);
-			input_sync(lradc->ts_input);
-		}
-
-		valid = false;
-
-		val_x = mxs_lradc_ts_sample_filter(lradc, LRADC_SAMPLE_X);
-		if (val_x < 0)
-			continue;
-		val_y = mxs_lradc_ts_sample_filter(lradc, LRADC_SAMPLE_Y);
-		if (val_y < 0)
-			continue;
-		val_p = mxs_lradc_ts_sample_filter(lradc, LRADC_SAMPLE_PRESSURE);
-		if (val_p < 0)
-			continue;
-
-		valid = true;
-	}
-
-	input_report_abs(lradc->ts_input, ABS_PRESSURE, 0);
-	input_report_key(lradc->ts_input, BTN_TOUCH, 0);
-	input_sync(lradc->ts_input);
-
-	/* Restart the touchscreen interrupts. */
-	mxs_lradc_reg_clear(lradc, LRADC_CTRL1_TOUCH_DETECT_IRQ, LRADC_CTRL1);
-	mxs_lradc_reg_set(lradc, LRADC_CTRL1_TOUCH_DETECT_IRQ_EN, LRADC_CTRL1);
-}
-
 static int mxs_lradc_ts_open(struct input_dev *dev)
 {
 	struct mxs_lradc *lradc = input_get_drvdata(dev);
@@ -1054,8 +891,6 @@ static void mxs_lradc_ts_unregister(struct mxs_lradc *lradc)
 	if (!lradc->use_touchscreen)
 		return;
 
-	cancel_work_sync(&lradc->ts_work);
-
 	mxs_lradc_disable_ts(lradc);
 	input_unregister_device(lradc->ts_input);
 }
Signature · 1 line
1.8.4.rc3