v7-M support using MULTIPLATFORM
cover v7-M support using MULTIPLATFORM
Hello,
this series makes it possible to benefit from the MULTIPLATFORM stuff also for my v7-M machine (that is not yet supported in mainline).
Best regards
Uwe
Uwe Kleine-K?nig (3):
ARM: drop !ARCH_MULTIPLATFORM dependency of XIP_KERNEL
ARM: allow MULTIPLATFORM on no-MMU machines [RFC] ARM: prepare ARMv7-M for MULTIPLATFORM use
arch/arm/Kconfig | 16 ++++++++++------ arch/arm/kernel/entry-v7m.S | 6 ++++-- 2 files changed, 14 insertions(+), 8 deletions(-)
Signature · 1 line
1.8.4.rc3
PATCH 1/3 ARM: drop !ARCH_MULTIPLATFORM dependency of XIP_KERNEL
Enabling XIP_KERNEL requires specifying the physical address of the readonly memory. As these addresses vary among different SoCs and even machines with the same SoC enabling XIP_KERNEL might restrict the set of machines that can run the resulting kernel to a subset of the configured in machines.
Still allowing XIP_KERNEL for a MULTIPLATFORM kernel makes sense as for some platforms MULTIPLATFORM is mandatory (e.g. bcm, highbank or imx). So to allow compiling a XIP kernel for these platforms, allow selecting XIP in the presence of ARCH_MULTIPLATFORM.
---
This patch might be problematic for compile coverage testing according to Arnd. Still I need XIP for my efm32 machine as it only features 4 MiB of RAM.
--- arch/arm/Kconfig | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
arch/arm/Kconfig +1 -1
@@ -2092,7 +2092,7 @@ endchoice config XIP_KERNEL bool "Kernel Execute-In-Place from ROM" - depends on !ZBOOT_ROM && !ARM_LPAE && !ARCH_MULTIPLATFORM + depends on !ZBOOT_ROM && !ARM_LPAE help Execute-In-Place allows the kernel to run from non-volatile storage directly addressable by the CPU, such as NOR flash. This saves RAM
Signature · 1 line
1.8.4.rc3
PATCH 2/3 ARM: allow MULTIPLATFORM on no-MMU machines
In reply to Uwe Kleine-KönigThere is no technical reason to not use the benefits of MULTIPLATFORM on a no-MMU machine and my not-yet-mainline efm32 port does work just fine with it. So drop the dependency.
--- arch/arm/Kconfig | 3 +-- 1 file changed, 1 insertion(+), 2 deletions(-)
arch/arm/Kconfig +1 -2
@@ -296,8 +296,7 @@ choice config ARCH_MULTIPLATFORM bool "Allow multiple platforms to be selected" - depends on MMU - select ARM_PATCH_PHYS_VIRT + select ARM_PATCH_PHYS_VIRT if MMU && !XIP_KERNEL select AUTO_ZRELADDR select COMMON_CLK select MULTI_IRQ_HANDLER
Signature · 1 line
1.8.4.rc3
PATCH 2/3 ARM: allow MULTIPLATFORM on no-MMU machines
Quoted 15 lines · Uwe Kleine-K?nig
There is no technical reason to not use the benefits of MULTIPLATFORM on a no-MMU machine and my not-yet-mainline efm32 port does work just fine with it. So drop the dependency.
Signed-off-by Uwe Kleine-K?nig <[email protected]>--- arch/arm/Kconfig | 3 +-- 1 file changed, 1 insertion(+), 2 deletions(-)arch/arm/Kconfig +0
-0
arch/arm/Kconfig choice · line 302
Quoted 9 lines
arch/arm/Kconfig +1
-2@@ -296,8 +296,7 @@ choice config ARCH_MULTIPLATFORM bool "Allow multiple platforms to be selected" - depends on MMU - select ARM_PATCH_PHYS_VIRT + select ARM_PATCH_PHYS_VIRT if MMU && !XIP_KERNEL select AUTO_ZRELADDR select COMMON_CLK select MULTI_IRQ_HANDLER
A patch much like this has been submitted in the past by Arnd and me, and Russell wasn't too happy with the idea because ARCH_MULTIPLATFORM doesn't really make sense for !MMU.
However, back then we were talking R/A class. For M-class the memory map is more clearly mandated, the idea of V7M platforms that are ARCH_MULTIPLATFORM compatible is much more feasible. One of the big issues for !MMU/ARCH_MULTIPLATFORM in the past was the need to select the vector configuration at build time - not something we need to worry about with V7M (where we have a configurable vector base), so from that point of view, this change makes sense.
But I'm not sure about the XIP_KERNEL part. Once you're using XIP_KERNEL again, multi-platform doesn't make much sense. Uwe, can you correct me on that?
Jonny
RFC PATCH 3/3 ARM: prepare ARMv7-M for MULTIPLATFORM use
In reply to Uwe Kleine-Königv7-M is a third group that is incompatible with both v4/v5 and v6/v7.
---
This behaves strange but I think is robust not to allow broken configs:
When v4/v5 is selected, v6/v7 and v7m are available for enabling, too. When v6/v7 is selected the other choices are disabled
When v7m is selected only v6/v7 are available for enabling.
--- arch/arm/Kconfig | 11 ++++++++--- arch/arm/kernel/entry-v7m.S | 6 ++++-- 2 files changed, 12 insertions(+), 5 deletions(-)
arch/arm/Kconfig +8 -3
@@ -881,7 +881,7 @@ comment "CPU Core family selection" config ARCH_MULTI_V4T bool "ARMv4T based platforms (ARM720T, ARM920T, ...)" - depends on !ARCH_MULTI_V6_V7 + depends on !ARCH_MULTI_V6_V7 && !ARCH_MULTI_V7M select ARCH_MULTI_V4_V5 select CPU_ARM920T if !(CPU_ARM7TDMI || CPU_ARM720T || \ CPU_ARM740T || CPU_ARM9TDMI || CPU_ARM922T || \
@@ -889,7 +889,7 @@ config ARCH_MULTI_V4T config ARCH_MULTI_V5 bool "ARMv5 based platforms (ARM926T, XSCALE, PJ1, ...)" - depends on !ARCH_MULTI_V6_V7 + depends on !ARCH_MULTI_V6_V7 && !ARCH_MULTI_V7M select ARCH_MULTI_V4_V5 select CPU_ARM926T if (!CPU_ARM946E || CPU_ARM1020 || \ CPU_ARM1020E || CPU_ARM1022 || CPU_ARM1026 || \
@@ -912,8 +912,13 @@ config ARCH_MULTI_V7 config ARCH_MULTI_V6_V7 bool +config ARCH_MULTI_V7M + bool "ARMv7-M based platforms (Cortex-M)" + depends on !ARCH_MULTI_V6_V7 && !MMU + select CPU_V7M + config ARCH_MULTI_CPU_AUTO - def_bool !(ARCH_MULTI_V4 || ARCH_MULTI_V4T || ARCH_MULTI_V6_V7) + def_bool !(ARCH_MULTI_V4 || ARCH_MULTI_V4T || ARCH_MULTI_V6_V7 || ARCH_MULTI_V7M) select ARCH_MULTI_V5 endmenu
arch/arm/kernel/entry-v7m.S +4 -2
@@ -14,8 +14,6 @@ #include <asm/thread_notify.h> #include <asm/v7m.h> -#include <mach/entry-macro.S> - #include "entry-header.S" #ifdef CONFIG_TRACE_IRQFLAGS
@@ -141,3 +139,7 @@ ENTRY(vector_table) .rept 64 - 16 .long __irq_entry @ 16..64 - External Interrupts .endr + + .globl handle_arch_irq +handle_arch_irq: + .long 0
Signature · 1 line
1.8.4.rc3
RFC PATCH 3/3 ARM: prepare ARMv7-M for MULTIPLATFORM use
Quoted 9 lines · Uwe Kleine-K?nig
v7-M is a third group that is incompatible with both v4/v5 and v6/v7.
Signed-off-by Uwe Kleine-K?nig <[email protected]>---
This behaves strange but I think is robust not to allow broken configs:When v4/v5 is selected, v6/v7 and v7m are available for enabling, too. When v6/v7 is selected the other choices are disabled
When v7m is selected only v6/v7 are available for enabling.
The Kconfig stuff all looks good,
Quoted 23 lines
arch/arm/kernel/entry-v7m.S +4
-2@@ -14,8 +14,6 @@ #include <asm/thread_notify.h> #include <asm/v7m.h> -#include <mach/entry-macro.S> - #include "entry-header.S" #ifdef CONFIG_TRACE_IRQFLAGS@@ -141,3 +139,7 @@ ENTRY(vector_table) .rept 64 - 16 .long __irq_entry @ 16..64 - External Interrupts .endr + + .globl handle_arch_irq +handle_arch_irq: + .long 0Signature · 1 line
1.8.4.rc3
I'm not sure about this part. I guess you should either make it a separate patch, or describe what it's for in the patch description above.
Also, I'd put all of the text you have in the comment into the actual changeset text, above the --- line, as others might find that useful later.
Arnd
RFC PATCH 3/3 ARM: prepare ARMv7-M for MULTIPLATFORM use
Hello Arnd,
Quoted 7 lines · Arnd Bergmann
Quoted 6 lines · Uwe Kleine-K?nig
v7-M is a third group that is incompatible with both v4/v5 and v6/v7.
Signed-off-by Uwe Kleine-K?nig <[email protected]>---
This behaves strange but I think is robust not to allow broken configs:
Quoted 7 lines
Quoted 3 lines
When v4/v5 is selected, v6/v7 and v7m are available for enabling, too. When v6/v7 is selected the other choices are disabled
When v7m is selected only v6/v7 are available for enabling.The
Kconfigstuff all looks good,Acked-by Arnd Bergmann <[email protected]>
Thanks
Quoted 5 lines
Quoted 5 lines
arch/arm/kernel/entry-v7m.S +1
-0@@ -141,3 +139,7 @@ ENTRY(vector_table) .rept 64 - 16 .long __irq_entry @ 16..64 - External Interrupts .endr +
Quoted 8 lines
Quoted 5 lines
arch/arm/kernel/entry-v7m.S +3
-0+ .globl handle_arch_irq +handle_arch_irq: + .long 0Signature · 1 line
1.8.4.rc3I'm not sure about this part. I guess you should either make it a separate patch, or describe what it's for in the patch description above.
This is needed because ARCH_MULTIPLATFORM selects MULTI_IRQ_HANDLER which v7-M didn't use up to now. I will wait for a while for more feedback then respin with a better changelog.
Quoted 3 lines
Also, I'd put all of the text you have in the comment into the actual changeset text, above the --- line, as others might find that useful later.
ok
Uwe
Signature · 2 lines
Pengutronix e.K. | Uwe Kleine-K?nig | Industrial Linux Solutions | http://www.pengutronix.de/ |
RFC PATCH 3/3 ARM: prepare ARMv7-M for MULTIPLATFORM use
In reply to Arnd BergmannQuoted 7 lines · Arnd Bergmann
Quoted 6 lines · Uwe Kleine-K?nig
v7-M is a third group that is incompatible with both v4/v5 and v6/v7.
Signed-off-by Uwe Kleine-K?nig <[email protected]>---
This behaves strange but I think is robust not to allow broken configs:
Quoted 5 lines
Quoted 3 lines
When v4/v5 is selected, v6/v7 and v7m are available for enabling, too. When v6/v7 is selected the other choices are disabled
When v7m is selected only v6/v7 are available for enabling.The
Kconfigstuff all looks good,
Actually this is a choice implemented using normal configs. Why not a using a choice here:
choice
prompt "CPU Core family selection"
config ARCH_MULTI_V4_V5
bool "..."
config ARCH_MULTI_V6_V7
bool "..."
config ARCH_MULTI_V7M
bool "..."
endchoice
config ARCH_MULTI_V4T
bool "ARMv4T based platforms (ARM720T, ARM920T, ...)" depends on ARCH_MULTI_V4_V5
config ARCH_MULTI_V5
bool "ARMv5 based platforms (ARM926T, XSCALE, PJ1, ...)" if ARCH_MULTI_V4T depends on ARCH_MULTI_V4_V5
default y if !ARCH_MULTI_V4T
config ARCH_MULTI_V6
...
config ARCH_MULTI_V7
...
Best regards
Uwe
Signature · 2 lines
Pengutronix e.K. | Uwe Kleine-K?nig | Industrial Linux Solutions | http://www.pengutronix.de/ |
cover v7-M support using MULTIPLATFORM
In reply to Uwe Kleine-KönigQuoted 4 lines · Uwe Kleine-K?nig
Hello,
this series makes it possible to benefit from the MULTIPLATFORM stuff also for my v7-M machine (that is not yet supported in mainline).
The big problem I have with this is that the single zImage project is forcing itself onto stuff like the small embedded stuff where it's not appropriate for it to be.
Much of the multiplatform infrastructure relies on the ability to do tricks with the MMU - placing various peripherals at known virtual addresses. Such tricks don't work on no-MMU platforms.
NoMMU platforms are inherently much more restricted and specialised, and having multiplatform on them just doesn't make sense. Yes, it may give you the ability to increase compilation coverage, but will the resulting image even work on the platform you're trying to target, or will one of the other multi-platforms take over some settings and screw it for you - like the link address.
XIP kernel is inherently limited to a single class of platforms. Think about it - it's a very specialised. XIP kernel needs several things - it needs the kernel built in a special way such that the data segment is separate from the text segment. It needs to map the flash memory storing the kernel code separately from the SDRAM. It needs to know where the IRQ controller is and how to access it to check for pending interrupts.
None of that is provided by the majority of multiplatform.
So, enabling the multiplatform Kconfig on such specialist platforms is just opening up a huge can of worms. Why anyone thinks this is a good idea is way beyond me.
Also think about the argument you're making. You need XIP kernel because you have limited RAM, but you're willing to enable multiplatform support which will allow you to build a kernel much larger than is necessary for your platform by including other platforms in it. Sorry, that's just stupid.
So no. If multiplatform gets in the way on noMMU platforms, then multiplatform has ended up being done wrongly, and its multiplatform that needs to be fixed.
cover v7-M support using MULTIPLATFORM
Hello Russell,
Quoted 6 lines · Russell King - ARM Linux
Quoted 4 lines · Uwe Kleine-K?nig
Hello,
this series makes it possible to benefit from the MULTIPLATFORM stuff also for my v7-M machine (that is not yet supported in mainline).
Quoted 7 lines
The big problem I have with this is that the single zImage project is forcing itself onto stuff like the small embedded stuff where it's not appropriate for it to be.
Much of the multiplatform infrastructure relies on the ability to do tricks with the MMU - placing various peripherals at known virtual addresses. Such tricks don't work on no-MMU platforms.
Actually it's not for the multi-platform ability itself I selected it for, but to benefit from other stuff that is currently only available for it, i.e. I don't need a Makefile.boot, I don't need some mach/ headers.
Quoted 6 lines
NoMMU platforms are inherently much more restricted and specialised, and having multiplatform on them just doesn't make sense. Yes, it may give you the ability to increase compilation coverage, but will the resulting image even work on the platform you're trying to target, or will one of the other multi-platforms take over some settings and screw it for you - like the link address.
Well, the way things are suggested in my patches you can only select other v7m machines alongside the efm32 platform. The bets are much better there not to screw it for me. But of course I cannot proof this as there is only one Cortex-M3 type supported in my tree.
Quoted 5 lines
XIP kernel is inherently limited to a single class of platforms. Think about it - it's a very specialised. XIP kernel needs several things - it needs the kernel built in a special way such that the data segment is separate from the text segment. It needs to map the flash memory storing the kernel code separately from the SDRAM.
Right, but do we agree that it should be possible to create an XIP image for i.MX6? If so: You currently cannot, because i.MX6 isn't configurable without MULTIPLATFORM. Also in the times before MULTIPLATFORM XIP was special. Already back than you could create a kernel for 2 (or more) different machines (sharing the same SoC family) with XIP enabled. That didn't necessarily made it work on both machines, maybe only one of them had NOR flash.
So maybe the only problem is that the symbol is misnamed or at least gives expectations that are not necessarily true. So you can configure a MULTIPLATFORM kernel for a single machine only just fine.
Quoted 2 lines
It needs to know where the IRQ controller is and how to access it to check for pending interrupts.
I didn't configure that, maybe this is only needed for writing to the flash holding the XIP image?
Quoted 11 lines
None of that is provided by the majority of multiplatform.
So, enabling the multiplatform
Kconfigon such specialist platforms is just opening up a huge can of worms. Why anyone thinks this is a good idea is way beyond me.Also think about the argument you're making. You need XIP kernel because you have limited RAM, but you're willing to enable multiplatform support which will allow you to build a kernel much larger than is necessary for your platform by including other platforms in it. Sorry, that's just stupid.
Right, it will allow me to build a much bigger kernel (but I don't need to). And it allows me a few more things (yes please).
Note I'm not 100% convinced that multiplatform is a sane idea for v7-M, but still I see some advantages so I wouldn't call it stupid.
Best regards
Uwe
Signature · 2 lines
Pengutronix e.K. | Uwe Kleine-K?nig | Industrial Linux Solutions | http://www.pengutronix.de/ |
cover v7-M support using MULTIPLATFORM
Quoted 13 lines · Uwe Kleine-K?nig
Hello Russell,
Quoted 10 lines · Russell King - ARM Linux
Quoted 4 lines · Uwe Kleine-K?nig
Hello,
this series makes it possible to benefit from the MULTIPLATFORM stuff also for my v7-M machine (that is not yet supported in mainline).
The big problem I have with this is that the single zImage project is forcing itself onto stuff like the small embedded stuff where it's not appropriate for it to be.
Quoted 8 lines
Quoted 3 lines
Much of the multiplatform infrastructure relies on the ability to do tricks with the MMU - placing various peripherals at known virtual addresses. Such tricks don't work on no-MMU platforms.
Actually it's not for the multi-platform ability itself I selected it for, but to benefit from other stuff that is currently only available for it, i.e. I don't need a Makefile.boot, I don't need some mach/ headers.
The only include file which MULTIPLATFORM itself hides is mach/timex.h - the others are all optional wrt their individual NEED_xxx_H configs. We should probably convert mach/timex.h to the NEED_xxx_H style as well.
As for not needing Makefile.boot, I guess we should allow the 'Image' target to work if there's no Makefile.boot but disable the rest.
Quoted 10 lines
Quoted 6 lines
NoMMU platforms are inherently much more restricted and specialised, and having multiplatform on them just doesn't make sense. Yes, it may give you the ability to increase compilation coverage, but will the resulting image even work on the platform you're trying to target, or will one of the other multi-platforms take over some settings and screw it for you - like the link address.
Well, the way things are suggested in my patches you can only select other v7m machines alongside the efm32 platform. The bets are much better there not to screw it for me. But of course I cannot proof this as there is only one Cortex-M3 type supported in my tree.
Hmm. So, is it possible to build for the EFM32 platform and a SAM3N in the same kernel? The SAM3N devices are Cortex-M3 CPUs, with major regions defined as flash in the bottom .5G, SRAM, external SRAM at 0x60000000, private peripherals at 0xe0000000, which is where the system control block, system timer, nvic and so forth are located.
Quoted 4 lines
Right, but do we agree that it should be possible to create an XIP image for i.MX6? If so: You currently cannot, because i.MX6 isn't configurable without MULTIPLATFORM. Also in the times before MULTIPLATFORM XIP was special.
That's one of the consequences of pushing to multiplatform support - XIP has fallen by the way side as a result of this effort (it was discussed previously) and we had decided that almost no one uses it anymore and it would not be part of the multiplatform stuff. It was only really used by very few SA11x0 and PXA platforms anyway.
Quoted 4 lines
Already back than you could create a kernel for 2 (or more) different machines (sharing the same SoC family) with XIP enabled. That didn't necessarily made it work on both machines, maybe only one of them had NOR flash.
That's quite a different issue from enabling MULTIPLATFORM and then having a whole raft of completely different SoCs be configurable. For any one SoC, it will work if you program the kernel into memory starting at XIP_PHYS_ADDR. The majority of platforms in any one SoC group will have memory available at a fixed location. For example, on SA11x0, you can almost guarantee that there's some kind of flash memory in flash bank 0, because that's how the system boots. Same for PXA.
Quoted 4 lines
Quoted 2 lines
It needs to know where the IRQ controller is and how to access it to check for pending interrupts.
I didn't configure that, maybe this is only needed for writing to the flash holding the XIP image?
Correct, which makes the flash effectively ROM.
Quoted 6 lines
Quoted 6 lines
None of that is provided by the majority of multiplatform.
So, enabling the multiplatform
Kconfigon such specialist platforms is just opening up a huge can of worms. Why anyone thinks this is a good idea is way beyond me.
Quoted 8 lines
Quoted 5 lines
Also think about the argument you're making. You need XIP kernel because you have limited RAM, but you're willing to enable multiplatform support which will allow you to build a kernel much larger than is necessary for your platform by including other platforms in it. Sorry, that's just stupid.
Right, it will allow me to build a much bigger kernel (but I don't need to). And it allows me a few more things (yes please).
"a few more things" - I count two things which you've mentioned so far, both of which can be sorted out. Anything else?
cover v7-M support using MULTIPLATFORM
Quoted 11 lines · Russell King - ARM Linux
Quoted 4 lines · Uwe Kleine-K?nig
Right, but do we agree that it should be possible to create an XIP image for i.MX6? If so: You currently cannot, because i.MX6 isn't configurable without MULTIPLATFORM. Also in the times before MULTIPLATFORM XIP was special.
That's one of the consequences of pushing to multiplatform support - XIP has fallen by the way side as a result of this effort (it was discussed previously) and we had decided that almost no one uses it anymore and it would not be part of the multiplatform stuff. It was only really used by very few SA11x0 and PXA platforms anyway.
Semantically, MULTIPLATFORM is incompatible with XIP as well as NOMMU.
So if a platform exists only when MULTIPLATFORM is selected, preventing it from being configured as NOMMU or XIP then something is broken with MULTIPLATFORM.
Nicolas
cover v7-M support using MULTIPLATFORM
Hello Nicolas,
Quoted 14 lines · Nicolas Pitre
Quoted 11 lines · Russell King - ARM Linux
Quoted 4 lines · Uwe Kleine-K?nig
Right, but do we agree that it should be possible to create an XIP image for i.MX6? If so: You currently cannot, because i.MX6 isn't configurable without MULTIPLATFORM. Also in the times before MULTIPLATFORM XIP was special.
That's one of the consequences of pushing to multiplatform support - XIP has fallen by the way side as a result of this effort (it was discussed previously) and we had decided that almost no one uses it anymore and it would not be part of the multiplatform stuff. It was only really used by very few SA11x0 and PXA platforms anyway.
Quoted 5 lines
Semantically, MULTIPLATFORM is incompatible with XIP as well as NOMMU.
So if a platform exists only when MULTIPLATFORM is selected, preventing it from being configured as NOMMU or XIP then something is broken with MULTIPLATFORM.
Is this an Ack for patch 1 in this series?
Best regards
Uwe
Signature · 2 lines
Pengutronix e.K. | Uwe Kleine-K?nig | Industrial Linux Solutions | http://www.pengutronix.de/ |
cover v7-M support using MULTIPLATFORM
Quoted 17 lines · Uwe Kleine-K?nig
Hello Nicolas,
Quoted 14 lines · Nicolas Pitre
Quoted 11 lines · Russell King - ARM Linux
Quoted 4 lines · Uwe Kleine-K?nig
Right, but do we agree that it should be possible to create an XIP image for i.MX6? If so: You currently cannot, because i.MX6 isn't configurable without MULTIPLATFORM. Also in the times before MULTIPLATFORM XIP was special.
That's one of the consequences of pushing to multiplatform support - XIP has fallen by the way side as a result of this effort (it was discussed previously) and we had decided that almost no one uses it anymore and it would not be part of the multiplatform stuff. It was only really used by very few SA11x0 and PXA platforms anyway.
Quoted 6 lines
Quoted 5 lines
Semantically, MULTIPLATFORM is incompatible with XIP as well as NOMMU.
So if a platform exists only when MULTIPLATFORM is selected, preventing it from being configured as NOMMU or XIP then something is broken with MULTIPLATFORM.
Is this an Ack for patch 1 in this series?
Uwe, have you seen that patch that Jonathan Austin was working on to reorganize the platform selection for multiplatform? I don't know if he has gotten around the time to post it on the mailing list, if not he can probably follow up here.
Arnd
cover v7-M support using MULTIPLATFORM
In reply to Russell King - ARM LinuxHi Russell,
Quoted 21 lines · Russell King - ARM Linux
Quoted 11 lines · Uwe Kleine-K?nig
Quoted 10 lines · Russell King - ARM Linux
Quoted 4 lines · Uwe Kleine-K?nig
Hello,
this series makes it possible to benefit from the MULTIPLATFORM stuff also for my v7-M machine (that is not yet supported in mainline).
The big problem I have with this is that the single zImage project is forcing itself onto stuff like the small embedded stuff where it's not appropriate for it to be.
Quoted 8 lines
Quoted 3 lines
Much of the multiplatform infrastructure relies on the ability to do tricks with the MMU - placing various peripherals at known virtual addresses. Such tricks don't work on no-MMU platforms.
Actually it's not for the multi-platform ability itself I selected it for, but to benefit from other stuff that is currently only available for it, i.e. I don't need a Makefile.boot, I don't need some mach/ headers.
Quoted 6 lines
The only include file which MULTIPLATFORM itself hides is
mach/timex.h- the others are all optional wrt their individualNEED_xxx_Hconfigs. We should probably convertmach/timex.hto theNEED_xxx_Hstyle as well.As for not needing Makefile.boot, I guess we should allow the 'Image' target to work if there's no Makefile.boot but disable the rest.
Both suggestions sound fine for me.
Quoted 11 lines
Quoted 10 lines
Quoted 6 lines
NoMMU platforms are inherently much more restricted and specialised, and having multiplatform on them just doesn't make sense. Yes, it may give you the ability to increase compilation coverage, but will the resulting image even work on the platform you're trying to target, or will one of the other multi-platforms take over some settings and screw it for you - like the link address.
Well, the way things are suggested in my patches you can only select other v7m machines alongside the efm32 platform. The bets are much better there not to screw it for me. But of course I cannot proof this as there is only one Cortex-M3 type supported in my tree.
Quoted 5 lines
Hmm. So, is it possible to build for the EFM32 platform and a SAM3N in the same kernel? The SAM3N devices are Cortex-M3 CPUs, with major regions defined as flash in the bottom .5G, SRAM, external SRAM at
0x60000000, private peripherals at0xe0000000, which is where the system control block, system timer, nvic and so forth are located.
The block at 0xe0000000 is architecturally defined. Also flash at the bottom is quite usual I think. All M3 and M4 use the nvic as irq controller at a fixed address. So multi-arch on v7-M isn't as hard as it could be.
Quoted 10 lines
Quoted 4 lines
Right, but do we agree that it should be possible to create an XIP image for i.MX6? If so: You currently cannot, because i.MX6 isn't configurable without MULTIPLATFORM. Also in the times before MULTIPLATFORM XIP was special.
That's one of the consequences of pushing to multiplatform support - XIP has fallen by the way side as a result of this effort (it was discussed previously) and we had decided that almost no one uses it anymore and it would not be part of the multiplatform stuff. It was only really used by very few SA11x0 and PXA platforms anyway.
I assume that new machines using efm32 (or any other M3) that are targeted to run Linux will have bigger RAMs and so the XIP part will matter less here.
Quoted 5 lines
Quoted 4 lines
Already back than you could create a kernel for 2 (or more) different machines (sharing the same SoC family) with XIP enabled. That didn't necessarily made it work on both machines, maybe only one of them had NOR flash.
Quoted 8 lines
That's quite a different issue from enabling MULTIPLATFORM and then having a whole raft of completely different SoCs be configurable. For any one SoC, it will work if you program the kernel into memory starting at
XIP_PHYS_ADDR. The majority of platforms in any one SoC group will have memory available at a fixed location. For example, on SA11x0, you can almost guarantee that there's some kind of flash memory in flash bank 0, because that's how the system boots. Same for PXA.
In my eyes that's a poor excuse to drop XIP. Yes, it doesn't make sense in all configurations, but in some it does. So IMHO better allow it in all configurations than in none.
Quoted 12 lines
Quoted 12 lines
Quoted 11 lines
None of that is provided by the majority of multiplatform.
So, enabling the multiplatform
Kconfigon such specialist platforms is just opening up a huge can of worms. Why anyone thinks this is a good idea is way beyond me.Also think about the argument you're making. You need XIP kernel because you have limited RAM, but you're willing to enable multiplatform support which will allow you to build a kernel much larger than is necessary for your platform by including other platforms in it. Sorry, that's just stupid.
Quoted 5 lines
Quoted 2 lines
Right, it will allow me to build a much bigger kernel (but I don't need to). And it allows me a few more things (yes please).
"a few more things" - I count two things which you've mentioned so far, both of which can be sorted out. Anything else?
Nothing I'm aware at the moment. I will address your two suggestions soon. Still I wonder if going the multi-arch route is the right thing to do now that it is (still) easy. And if it's only because it matches what the MMU machines are doing and so uses more better tested stuff.
Best regards
Uwe
Signature · 2 lines
Pengutronix e.K. | Uwe Kleine-K?nig | Industrial Linux Solutions | http://www.pengutronix.de/ |