Skip to contentSkip to conversation

usb: Fix error handling in musb_hcd.c

PATCH New Andrew Murray 2 participants 2 messages Oct 1, 2013 – Oct 3, 2013

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

PATCH 1/1 usb: Fix error handling in musb_hcd.c

The wait_until_[rx|tx]ep_ready functions return a u8 to indicate success containing the value 0, 1 or -1. This patch changes the return type to an int to accommodate the negative return values.

These functions are used in the file using calls such as if (!wait_until... Where a -1 is returned it is mishandled and treated as success instead of a CRC error. This patch addresses this.

---
 drivers/usb/musb/musb_hcd.c |   10 +++++-----
 1 file changed, 5 insertions(+), 5 deletions(-)
drivers/usb/musb/musb_hcd.c +5 -5
index ae39c4a..708fa12 100644
@@ -267,7 +267,7 @@ static int wait_until_ep0_ready(struct usb_device *dev, u32 bit_mask)
 /*
  * waits until tx ep is ready. Returns 1 when ep is ready and 0 on error.
  */
-static u8 wait_until_txep_ready(struct usb_device *dev, u8 ep)
+static int wait_until_txep_ready(struct usb_device *dev, u8 ep)
 {
 	u16 csr;
 	int timeout = CONFIG_MUSB_TIMEOUT;
@@ -299,7 +299,7 @@ static u8 wait_until_txep_ready(struct usb_device *dev, u8 ep)
 /*
  * waits until rx ep is ready. Returns 1 when ep is ready and 0 on error.
  */
-static u8 wait_until_rxep_ready(struct usb_device *dev, u8 ep)
+static int wait_until_rxep_ready(struct usb_device *dev, u8 ep)
 {
 	u16 csr;
 	int timeout = CONFIG_MUSB_TIMEOUT;
@@ -1018,7 +1018,7 @@ int submit_bulk_msg(struct usb_device *dev, unsigned long pipe,
 			writew(csr | MUSB_TXCSR_TXPKTRDY, &musbr->txcsr);
 
 			/* Wait until the TxPktRdy bit is cleared */
-			if (!wait_until_txep_ready(dev, MUSB_BULK_EP)) {
+			if (wait_until_txep_ready(dev, MUSB_BULK_EP) != 1) {
 				readw(&musbr->txcsr);
 				usb_settoggle(dev, ep, dir_out,
 				(csr >> MUSB_TXCSR_H_DATATOGGLE_SHIFT) & 1);
@@ -1053,7 +1053,7 @@ int submit_bulk_msg(struct usb_device *dev, unsigned long pipe,
 			writew(csr | MUSB_RXCSR_H_REQPKT, &musbr->rxcsr);
 
 			/* Wait until the RxPktRdy bit is set */
-			if (!wait_until_rxep_ready(dev, MUSB_BULK_EP)) {
+			if (wait_until_rxep_ready(dev, MUSB_BULK_EP) != 1) {
 				csr = readw(&musbr->rxcsr);
 				usb_settoggle(dev, ep, dir_out,
 				(csr >> MUSB_S_RXCSR_H_DATATOGGLE) & 1);
@@ -1226,7 +1226,7 @@ int submit_int_msg(struct usb_device *dev, unsigned long pipe,
 			writew(csr | MUSB_RXCSR_H_REQPKT, &musbr->rxcsr);
 
 			/* Wait until the RxPktRdy bit is set */
-			if (!wait_until_rxep_ready(dev, MUSB_INTR_EP)) {
+			if (wait_until_rxep_ready(dev, MUSB_INTR_EP) != 1) {
 				csr = readw(&musbr->rxcsr);
 				usb_settoggle(dev, ep, dir_out,
 				(csr >> MUSB_S_RXCSR_H_DATATOGGLE) & 1);
Signature · 1 line
1.7.9.5
#1 lore raw

PATCH 1/1 usb: Fix error handling in musb_hcd.c

Dear Andrew Murray,

Quoted 11 lines

The wait_until_[rx|tx]ep_ready functions return a u8 to indicate success containing the value 0, 1 or -1. This patch changes the return type to an int to accommodate the negative return values.

These functions are used in the file using calls such as if (!wait_until... Where a -1 is returned it is mishandled and treated as success instead of a CRC error. This patch addresses this.

Tom, feel free to pick this up if it's ok on this omap hardware.

Best regards,
Marek Vasut