ARM: dts: AM4372: Add more nodes
Subsystems (2)
cover ARM: dts: AM4372: Add more nodes
This patch series add nodes for l2-cache-controller, EDMA, mailbox, mmc, sham, and updates the properties for cpsw, i2c0, matrix-keypad.
These patches are applied on top of Benoit's for_3.13/dts branchgit://git.kernel.org/pub/scm/linux/kernel/git/bcousson/linux-omap-dt.git for_3.13/dts
Testing:
Tested EDMA, mmc, sham, aes, des, i2c0, cpsw, matric-keypad on AM4372 EPOS EVM with the addition of following two series:
-> Tero's V8 of OMAP DT clock conversion
http://www.mail-archive.com/linux-omap at vger.kernel.org/msg96769.html
-> Afzal's V5 of AM43x PRCM basic support
http://www.mail-archive.com/linux-omap at vger.kernel.org/msg96275.html
Lokesh Vutla (1):
ARM: dts: AM4372: Add more nodes
Mugunthan V N (1):
ARM: dts: AM4372: Update Support for EPOS EVM
arch/arm/boot/dts/am4372.dtsi | 210 +++++++++++++++++++++++++++++++++- arch/arm/boot/dts/am43x-epos-evm.dts | 168 +++++++++++++++++++++++++++ include/dt-bindings/pinctrl/am43xx.h | 31 +++++ 3 files changed, 408 insertions(+), 1 deletion(-) create mode 100644 include/dt-bindings/pinctrl/am43xx.h
Signature · 1 line
1.7.9.5
PATCH 1/2 ARM: dts: AM4372: Add more nodes
Populate nodes for l2-cache-controller, EDMA, mailbox, mmc, sham.
And also updating dt properties for epwmss, aes, des.
Few nodes are taken from a different tree that are added by Suman Anna <[email protected]> (Mailbox)
Balaji T K <[email protected]> (MMC)
Mugunthan V N <[email protected]> (Pinmux, Ethernet)
--- arch/arm/boot/dts/am4372.dtsi | 210 ++++++++++++++++++++++++++++++++++++++++- 1 file changed, 209 insertions(+), 1 deletion(-)
arch/arm/boot/dts/am4372.dtsi +209 -1
@@ -19,6 +19,8 @@ aliases { serial0 = &uart0; + ethernet0 = &cpsw_emac0; + ethernet1 = &cpsw_emac1; }; cpus {
@@ -39,11 +41,42 @@ <0x48240100 0x0100>; }; + l2-cache-controller at 48242000 { + compatible = "arm,pl310-cache"; + reg = <0x48242000 0x1000>; + cache-unified; + cache-level = <2>; + }; + + am43xx_pinmux: pinmux at 44e10800 { + compatible = "pinctrl-single"; + reg = <0x44e10800 0x31c>; + #address-cells = <1>; + #size-cells = <0>; + pinctrl-single,register-width = <32>; + pinctrl-single,function-mask = <0xffffffff>; + }; + ocp { compatible = "simple-bus"; #address-cells = <1>; #size-cells = <1>; ranges; + ti,hwmods = "l3_main"; + + edma: edma at 49000000 { + compatible = "ti,edma3"; + ti,hwmods = "tpcc", "tptc0", "tptc1", "tptc2"; + reg = <0x49000000 0x10000>, + <0x44e10f90 0x10>; + interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>; + #dma-cells = <1>; + dma-channels = <64>; + ti,edma-regions = <4>; + ti,edma-slots = <256>; + }; uart0: serial at 44e09000 { compatible = "ti,am4372-uart","ti,omap2-uart";
@@ -92,6 +125,18 @@ status = "disabled"; }; + mailbox: mailbox at 480C8000 { + compatible = "ti,omap4-mailbox"; + reg = <0x480C8000 0x200>; + interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>; + ti,hwmods = "mailbox"; + ti,mbox-num-users = <4>; + ti,mbox-num-fifos = <8>; + ti,mbox-names = "wkup_m3"; + ti,mbox-data = <0 0 0 0>; + status = "disabled"; + }; + timer1: timer at 44e31000 { compatible = "ti,am4372-timer-1ms","ti,am335x-timer-1ms"; reg = <0x44e31000 0x400>;
@@ -203,7 +248,6 @@ reg = <0x44e35000 0x1000>; interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>; ti,hwmods = "wd_timer2"; - status = "disabled"; }; gpio0: gpio at 44e07000 {
@@ -318,6 +362,40 @@ status = "disabled"; }; + mmc1: mmc at 48060000 { + compatible = "ti,omap4-hsmmc"; + reg = <0x48060000 0x1000>; + ti,hwmods = "mmc1"; + ti,dual-volt; + ti,needs-special-reset; + dmas = <&edma 24 + &edma 25>; + dma-names = "tx", "rx"; + interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + mmc2: mmc at 481d8000 { + compatible = "ti,omap4-hsmmc"; + reg = <0x481d8000 0x1000>; + ti,hwmods = "mmc2"; + ti,needs-special-reset; + dmas = <&edma 2 + &edma 3>; + dma-names = "tx", "rx"; + interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + mmc3: mmc at 47810000 { + compatible = "ti,omap4-hsmmc"; + reg = <0x47810000 0x1000>; + ti,hwmods = "mmc3"; + ti,needs-special-reset; + interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + spi1: spi at 481a0000 { compatible = "ti,am4372-mcspi","ti,omap4-mcspi"; reg = <0x481a0000 0x400>;
@@ -366,50 +444,173 @@ GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <1>; ti,hwmods = "cpgmac0"; status = "disabled"; + cpdma_channels = <8>; + ale_entries = <1024>; + bd_ram_size = <0x2000>; + no_bd_ram = <0>; + rx_descs = <64>; + mac_control = <0x20>; + slaves = <2>; + active_slave = <0>; + cpts_clock_mult = <0x80000000>; + cpts_clock_shift = <29>; + ranges; + + davinci_mdio: mdio at 4a101000 { + compatible = "ti,am4372-mdio","ti,davinci_mdio"; + reg = <0x4a101000 0x100>; + #address-cells = <1>; + #size-cells = <0>; + ti,hwmods = "davinci_mdio"; + bus_freq = <1000000>; + status = "disabled"; + }; + + cpsw_emac0: slave at 4a100200 { + /* Filled in by U-Boot */ + mac-address = [ 00 00 00 00 00 00 ]; + }; + + cpsw_emac1: slave at 4a100300 { + /* Filled in by U-Boot */ + mac-address = [ 00 00 00 00 00 00 ]; + }; }; epwmss0: epwmss at 48300000 { compatible = "ti,am4372-pwmss","ti,am33xx-pwmss"; reg = <0x48300000 0x10>; + #address-cells = <1>; + #size-cells = <1>; + ranges; ti,hwmods = "epwmss0"; status = "disabled"; + + ecap0: ecap at 48300100 { + compatible = "ti,am4372-ecap","ti,am33xx-ecap"; + reg = <0x48300100 0x80>; + ti,hwmods = "ecap0"; + status = "disabled"; + }; + + ehrpwm0: ehrpwm at 48300200 { + compatible = "ti,am4372-ehrpwm","ti,am33xx-ehrpwm"; + reg = <0x48300200 0x80>; + ti,hwmods = "ehrpwm0"; + status = "disabled"; + }; }; epwmss1: epwmss at 48302000 { compatible = "ti,am4372-pwmss","ti,am33xx-pwmss"; reg = <0x48302000 0x10>; + #address-cells = <1>; + #size-cells = <1>; + ranges; ti,hwmods = "epwmss1"; status = "disabled"; + + ecap1: ecap at 48302100 { + compatible = "ti,am4372-ecap","ti,am33xx-ecap"; + reg = <0x48302100 0x80>; + ti,hwmods = "ecap1"; + status = "disabled"; + }; + + ehrpwm1: ehrpwm at 48302200 { + compatible = "ti,am4372-ehrpwm","ti,am33xx-ehrpwm"; + reg = <0x48302200 0x80>; + ti,hwmods = "ehrpwm1"; + status = "disabled"; + }; }; epwmss2: epwmss at 48304000 { compatible = "ti,am4372-pwmss","ti,am33xx-pwmss"; reg = <0x48304000 0x10>; + #address-cells = <1>; + #size-cells = <1>; + ranges; ti,hwmods = "epwmss2"; status = "disabled"; + + ecap2: ecap at 48304100 { + compatible = "ti,am4372-ecap","ti,am33xx-ecap"; + reg = <0x48304100 0x80>; + ti,hwmods = "ecap2"; + status = "disabled"; + }; + + ehrpwm2: ehrpwm at 48304200 { + compatible = "ti,am4372-ehrpwm","ti,am33xx-ehrpwm"; + reg = <0x48304200 0x80>; + ti,hwmods = "ehrpwm2"; + status = "disabled"; + }; }; epwmss3: epwmss at 48306000 { compatible = "ti,am4372-pwmss","ti,am33xx-pwmss"; reg = <0x48306000 0x10>; + #address-cells = <1>; + #size-cells = <1>; + ranges; ti,hwmods = "epwmss3"; status = "disabled"; + + ehrpwm3: ehrpwm at 48306200 { + compatible = "ti,am4372-ehrpwm","ti,am33xx-ehrpwm"; + reg = <0x48306200 0x80>; + ti,hwmods = "ehrpwm3"; + status = "disabled"; + }; }; epwmss4: epwmss at 48308000 { compatible = "ti,am4372-pwmss","ti,am33xx-pwmss"; reg = <0x48308000 0x10>; + #address-cells = <1>; + #size-cells = <1>; + ranges; ti,hwmods = "epwmss4"; status = "disabled"; + + ehrpwm4: ehrpwm at 48308200 { + compatible = "ti,am4372-ehrpwm","ti,am33xx-ehrpwm"; + reg = <0x48308200 0x80>; + ti,hwmods = "ehrpwm4"; + status = "disabled"; + }; }; epwmss5: epwmss at 4830a000 { compatible = "ti,am4372-pwmss","ti,am33xx-pwmss"; reg = <0x4830a000 0x10>; + #address-cells = <1>; + #size-cells = <1>; + ranges; ti,hwmods = "epwmss5"; status = "disabled"; + + ehrpwm5: ehrpwm at 4830a200 { + compatible = "ti,am4372-ehrpwm","ti,am33xx-ehrpwm"; + reg = <0x4830a200 0x80>; + ti,hwmods = "ehrpwm5"; + status = "disabled"; + }; + }; + + sham: sham at 53100000 { + compatible = "ti,omap5-sham"; + ti,hwmods = "sham"; + reg = <0x53100000 0x300>; + dmas = <&edma 36>; + dma-names = "rx"; + interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>; }; aes: aes at 53501000 {
@@ -417,6 +618,9 @@ ti,hwmods = "aes"; reg = <0x53501000 0xa0>; interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&edma 6 + &edma 5>; + dma-names = "tx", "rx"; }; des: des at 53701000 {
@@ -424,6 +628,10 @@ ti,hwmods = "des"; reg = <0x53701000 0xa0>; interrupts = <GIC_SPI 130 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&edma 34 + &edma 33>; + dma-names = "tx", "rx"; }; + }; };
Signature · 1 line
1.7.9.5
PATCH 2/2 ARM: dts: AM4372: Update Support for EPOS EVM
In reply to Lokesh VutlaFrom: Mugunthan V N <[email protected]>
-> Adding pinmux for cpsw, i2c0.
-> Enabling the modules that are present in AM4372 EPOS EVM These modules are tested on AM4372 EPOS EVM.
--- arch/arm/boot/dts/am43x-epos-evm.dts | 168 ++++++++++++++++++++++++++++++++++ include/dt-bindings/pinctrl/am43xx.h | 31 +++++++ 2 files changed, 199 insertions(+) create mode 100644 include/dt-bindings/pinctrl/am43xx.h
arch/arm/boot/dts/am43x-epos-evm.dts +168 -0
@@ -11,8 +11,176 @@ /dts-v1/; #include "am4372.dtsi" +#include <dt-bindings/pinctrl/am43xx.h> +#include <dt-bindings/gpio/gpio.h> / { model = "TI AM43x EPOS EVM"; compatible = "ti,am43x-epos-evm","ti,am4372","ti,am43"; + + vmmcsd_fixed: fixedregulator-sd { + compatible = "regulator-fixed"; + regulator-name = "vmmcsd_fixed"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + enable-active-high; + }; + + am43xx_pinmux: pinmux at 44e10800 { + cpsw_default: cpsw_default { + pinctrl-single,pins = < + /* Slave 1 */ + 0x10c (PIN_INPUT_PULLDOWN | MUX_MODE1) /* mii1_crs.rmii1_crs */ + 0x110 (PIN_INPUT_PULLDOWN | MUX_MODE1) /* mii1_rxerr.rmii1_rxerr */ + 0x114 (PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* mii1_txen.rmii1_txen */ + 0x118 (PIN_INPUT_PULLDOWN | MUX_MODE1) /* mii1_rxdv.rmii1_rxdv */ + 0x124 (PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* mii1_txd1.rmii1_txd1 */ + 0x128 (PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* mii1_txd0.rmii1_txd0 */ + 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE1) /* mii1_rxd1.rmii1_rxd1 */ + 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE1) /* mii1_rxd0.rmii1_rxd0 */ + 0x144 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* rmii1_refclk.rmii1_refclk */ + >; + }; + + cpsw_sleep: cpsw_sleep { + pinctrl-single,pins = < + /* Slave 1 reset value */ + 0x10c (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x110 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x114 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x118 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x124 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x128 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x144 (PIN_INPUT_PULLDOWN | MUX_MODE7) + >; + }; + + davinci_mdio_default: davinci_mdio_default { + pinctrl-single,pins = < + /* MDIO */ + 0x148 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* mdio_data.mdio_data */ + 0x14c (PIN_OUTPUT_PULLUP | MUX_MODE0) /* mdio_clk.mdio_clk */ + >; + }; + + davinci_mdio_sleep: davinci_mdio_sleep { + pinctrl-single,pins = < + /* MDIO reset value */ + 0x148 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x14c (PIN_INPUT_PULLDOWN | MUX_MODE7) + >; + }; + + i2c0_pins: pinmux_i2c0_pins { + pinctrl-single,pins = < + 0x188 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* i2c0_sda.i2c0_sda */ + 0x18c (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* i2c0_scl.i2c0_scl */ + >; + }; + }; + + matrix_keypad: matrix_keypad at 0 { + compatible = "gpio-matrix-keypad"; + debounce-delay-ms = <5>; + col-scan-delay-us = <2>; + + row-gpios = <&gpio0 12 GPIO_ACTIVE_HIGH /* Bank0, pin12 */ + &gpio0 13 GPIO_ACTIVE_HIGH /* Bank0, pin13 */ + &gpio0 14 GPIO_ACTIVE_HIGH /* Bank0, pin14 */ + &gpio0 15 GPIO_ACTIVE_HIGH>; /* Bank0, pin15 */ + + col-gpios = <&gpio3 9 GPIO_ACTIVE_HIGH /* Bank3, pin9 */ + &gpio3 10 GPIO_ACTIVE_HIGH /* Bank3, pin10 */ + &gpio2 18 GPIO_ACTIVE_HIGH /* Bank2, pin18 */ + &gpio2 19 GPIO_ACTIVE_HIGH>; /* Bank2, pin19 */ + + linux,keymap = <0x00000201 /* P1 */ + 0x01000204 /* P4 */ + 0x02000207 /* P7 */ + 0x0300020a /* NUMERIC_STAR */ + 0x00010202 /* P2 */ + 0x01010205 /* P5 */ + 0x02010208 /* P8 */ + 0x03010200 /* P0 */ + 0x00020203 /* P3 */ + 0x01020206 /* P6 */ + 0x02020209 /* P9 */ + 0x0302020b /* NUMERIC_POUND */ + 0x00030067 /* UP */ + 0x0103006a /* RIGHT */ + 0x0203006c /* DOWN */ + 0x03030069>; /* LEFT */ + }; +}; + +&mmc1 { + status = "okay"; + vmmc-supply = <&vmmcsd_fixed>; + bus-width = <4>; +}; + +&mac { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&cpsw_default>; + pinctrl-1 = <&cpsw_sleep>; + status = "okay"; +}; + +&davinci_mdio { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&davinci_mdio_default>; + pinctrl-1 = <&davinci_mdio_sleep>; + status = "okay"; +}; + +&cpsw_emac0 { + phy_id = <&davinci_mdio>, <16>; + phy-mode = "rmii"; +}; + +&cpsw_emac1 { + phy_id = <&davinci_mdio>, <1>; + phy-mode = "rmii"; +}; + +&i2c0 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pins>; + + at24 at 50 { + compatible = "at24,24c256"; + pagesize = <64>; + reg = <0x50>; + }; + + pixcir_ts at 5c { + compatible = "pixcir,pixcir_ts"; + reg = <0x5c>; + interrupt-parent = <&gpio1>; + interrupts = <17 0>; + + attb-gpio = <&gpio1 17 GPIO_ACTIVE_HIGH>; + + x-size = <1024>; + y-size = <768>; + }; +}; + +&gpio0 { + status = "okay"; +}; + +&gpio1 { + status = "okay"; +}; + +&gpio2 { + status = "okay"; +}; + +&gpio3 { + status = "okay"; };
include/dt-bindings/pinctrl/am43xx.h new file +31 -0
@@ -0,0 +1,31 @@ +/* +* This header provides constants specific to AM43XX pinctrl bindings. +*/ + +#ifndef _DT_BINDINGS_PINCTRL_AM43XX_H +#define _DT_BINDINGS_PINCTRL_AM43XX_H + +#define MUX_MODE0 0 +#define MUX_MODE1 1 +#define MUX_MODE2 2 +#define MUX_MODE3 3 +#define MUX_MODE4 4 +#define MUX_MODE5 5 +#define MUX_MODE6 6 +#define MUX_MODE7 7 + +#define PULL_DISABLE (1 << 16) +#define PULL_UP (1 << 17) +#define INPUT_EN (1 << 18) +#define SLEWCTRL_FAST (1 << 19) +#define DS0_PULL_UP_DOWN_EN (1 << 27) + +#define PIN_OUTPUT (PULL_DISABLE) +#define PIN_OUTPUT_PULLUP (PULL_UP) +#define PIN_OUTPUT_PULLDOWN 0 +#define PIN_INPUT (INPUT_EN | PULL_DISABLE) +#define PIN_INPUT_PULLUP (INPUT_EN | PULL_UP) +#define PIN_INPUT_PULLDOWN (INPUT_EN) + +#endif +
Signature · 1 line
1.7.9.5
cover ARM: dts: AM4372: Add more nodes
In reply to Lokesh VutlaHi,
Quoted 6 lines · Lokesh Vutla
This patch series add nodes for l2-cache-controller, EDMA, mailbox, mmc, sham, and updates the properties for cpsw, i2c0, matrix-keypad.
These patches are applied on top of Benoit's for_3.13/dts branch
git://git.kernel.org/pub/scm/linux/kernel/git/bcousson/linux-omap-dt.gitfor_3.13/dts
Quoted 7 lines
Testing:
Tested EDMA, mmc, sham, aes, des, i2c0, cpsw, matric-keypad on AM4372 EPOS EVM with the addition of following two series:
-> Tero's V8 of OMAP DT clock conversion
http://www.mail-archive.com/linux-omap at vger.kernel.org/msg96769.html
-> Afzal's V5 of AM43x PRCM basic support
http://www.mail-archive.com/linux-omap at vger.kernel.org/msg96275.html
one extra piece of info:
all these patches are fresh out of Wakeup, tested on top of v3.12-rc3.
Signature · 8 lines
balbi -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 836 bytes Desc: Digital signature URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20131010/eb11c696/attachment.sig>
cover ARM: dts: AM4372: Add more nodes
In reply to Lokesh VutlaHi Benoit,
Quoted 5 lines · Lokesh Vutla
This patch series add nodes for l2-cache-controller, EDMA, mailbox, mmc, sham, and updates the properties for cpsw, i2c0, matrix-keypad.
These patches are applied on top of Benoit's for_3.13/dts branch
git://git.kernel.org/pub/scm/linux/kernel/git/bcousson/linux-omap-dt.gitfor_3.13/dts
Can you take this patch series for 3.13?
Thanks and regards,
Lokesh
Quoted 21 lines
Testing:
Tested EDMA, mmc, sham, aes, des, i2c0, cpsw, matric-keypad on AM4372 EPOS EVM with the addition of following two series:
-> Tero's V8 of OMAP DT clock conversion
http://www.mail-archive.com/linux-omap at vger.kernel.org/msg96769.html
-> Afzal's V5 of AM43x PRCM basic support
http://www.mail-archive.com/linux-omap at vger.kernel.org/msg96275.htmlLokesh Vutla (1):
ARM: dts: AM4372: Add more nodesMugunthan V N (1):
ARM: dts: AM4372: Update Support for EPOS EVMarch/arm/boot/dts/am4372.dtsi | 210 +++++++++++++++++++++++++++++++++- arch/arm/boot/dts/am43x-epos-evm.dts | 168 +++++++++++++++++++++++++++ include/dt-bindings/pinctrl/am43xx.h | 31 +++++ 3 files changed, 408 insertions(+), 1 deletion(-) create mode 100644 include/dt-bindings/pinctrl/am43xx.h
cover ARM: dts: AM4372: Add more nodes
Hi Lokesh,
Quoted 8 lines · Lokesh Vutla
Hi Benoit,
Quoted 5 lines · Lokesh Vutla
This patch series add nodes for l2-cache-controller, EDMA, mailbox, mmc, sham, and updates the properties for cpsw, i2c0, matrix-keypad.
These patches are applied on top of Benoit's for_3.13/dts branch
git://git.kernel.org/pub/scm/linux/kernel/git/bcousson/linux-omap-dt.gitfor_3.13/dtsCan you take this patch series for 3.13?
I've just applied it after a sloght change in the subject and in the SoB list.
ARM: dts: AM4372: Add L2, EDMA, mailbox, MMC and SHAM nodes
Populate nodes for l2-cache-controller, EDMA, mailbox, mmc, sham.
Update as well DT properties for epwmss, aes, des.
I added all the author you listed in a more formal way.
Regards,
Benoit
Quoted 25 lines
Thanks and regards,
LokeshQuoted 21 lines
Testing:
Tested EDMA, mmc, sham, aes, des, i2c0, cpsw, matric-keypad on AM4372 EPOS EVM with the addition of following two series:
-> Tero's V8 of OMAP DT clock conversion
http://www.mail-archive.com/linux-omap at vger.kernel.org/msg96769.html
-> Afzal's V5 of AM43x PRCM basic support
http://www.mail-archive.com/linux-omap at vger.kernel.org/msg96275.htmlLokesh Vutla (1):
ARM: dts: AM4372: Add more nodesMugunthan V N (1):
ARM: dts: AM4372: Update Support for EPOS EVMarch/arm/boot/dts/am4372.dtsi | 210 +++++++++++++++++++++++++++++++++- arch/arm/boot/dts/am43x-epos-evm.dts | 168 +++++++++++++++++++++++++++ include/dt-bindings/pinctrl/am43xx.h | 31 +++++ 3 files changed, 408 insertions(+), 1 deletion(-)create mode 100644
include/dt-bindings/pinctrl/am43xx.h
Signature · 4 lines
Beno?t Cousson BayLibre Embedded Linux Technology Lab www.baylibre.com
cover ARM: dts: AM4372: Add more nodes
Hi Benoit,
Quoted 21 lines · Benoit Cousson
Hi Lokesh,
Quoted 8 lines · Lokesh Vutla
Hi Benoit,
Quoted 5 lines · Lokesh Vutla
This patch series add nodes for l2-cache-controller, EDMA, mailbox, mmc, sham, and updates the properties for cpsw, i2c0, matrix-keypad.
These patches are applied on top of Benoit's for_3.13/dts branch
git://git.kernel.org/pub/scm/linux/kernel/git/bcousson/linux-omap-dt.gitfor_3.13/dtsCan you take this patch series for 3.13?
I've just applied it after a sloght change in the subject and in the SoB list.
ARM: dts: AM4372: Add L2, EDMA, mailbox, MMC and SHAM nodes
Populate nodes for l2-cache-controller, EDMA, mailbox, mmc, sham.
Update as well DT properties for epwmss, aes, des.
Quoted 8 lines
Signed-off-by Suman Anna <[email protected]>Signed-off-by Balaji T K <[email protected]>Signed-off-by Mugunthan V N <[email protected]>Signed-off-by Lokesh Vutla <[email protected]>Signed-off-by Benoit Cousson <[email protected]>I added all the author you listed in a more formal way.
Thanks.
Regards,
Lokesh
Quoted 31 lines
Regards,
BenoitQuoted 25 lines
Thanks and regards,
LokeshQuoted 21 lines
Testing:
Tested EDMA, mmc, sham, aes, des, i2c0, cpsw, matric-keypad on AM4372 EPOS EVM with the addition of following two series:
-> Tero's V8 of OMAP DT clock conversion
http://www.mail-archive.com/linux-omap at vger.kernel.org/msg96769.html
-> Afzal's V5 of AM43x PRCM basic support
http://www.mail-archive.com/linux-omap at vger.kernel.org/msg96275.htmlLokesh Vutla (1):
ARM: dts: AM4372: Add more nodesMugunthan V N (1):
ARM: dts: AM4372: Update Support for EPOS EVMarch/arm/boot/dts/am4372.dtsi | 210 +++++++++++++++++++++++++++++++++- arch/arm/boot/dts/am43x-epos-evm.dts | 168 +++++++++++++++++++++++++++ include/dt-bindings/pinctrl/am43xx.h | 31 +++++ 3 files changed, 408 insertions(+), 1 deletion(-)create mode 100644
include/dt-bindings/pinctrl/am43xx.h