Make few omap3 boards device tree only

new file mode 100644
index 0000000..9c18adf
@@ -0,0 +1,52 @@
+/*
+ * Common file for GPMC connected smsc911x on omaps
+ *
+ * Note that the board specifc DTS file needs to specify
+ * ranges, pinctrl, reg, interrupt parent and interrupts.
+ */
+
+/ {
+	vddvario: regulator-vddvario {
+		  compatible = "regulator-fixed";
+		  regulator-name = "vddvario";
+		  regulator-always-on;
+	};
+
+	vdd33a: regulator-vdd33a {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd33a";
+		regulator-always-on;
+	};
+};
+
+&gpmc {
+	ethernet at gpmc {
+		compatible = "smsc,lan9221", "smsc,lan9115";
+		bank-width = <2>;
+		gpmc,mux-add-data;
+		gpmc,cs-on-ns = <0>;
+		gpmc,cs-rd-off-ns = <186>;
+		gpmc,cs-wr-off-ns = <186>;
+		gpmc,adv-on-ns = <12>;
+		gpmc,adv-rd-off-ns = <48>;
+		gpmc,adv-wr-off-ns = <48>;
+		gpmc,oe-on-ns = <54>;
+		gpmc,oe-off-ns = <168>;
+		gpmc,we-on-ns = <54>;
+		gpmc,we-off-ns = <168>;
+		gpmc,rd-cycle-ns = <186>;
+		gpmc,wr-cycle-ns = <186>;
+		gpmc,access-ns = <114>;
+		gpmc,page-burst-access-ns = <6>;
+		gpmc,bus-turnaround-ns = <12>;
+		gpmc,cycle2cycle-delay-ns = <18>;
+		gpmc,wr-data-mux-bus-ns = <90>;
+		gpmc,wr-access-ns = <186>;
+		gpmc,cycle2cycle-samecsen;
+		gpmc,cycle2cycle-diffcsen;
+		vmmc-supply = <&vddvario>;
+		vmmc_aux-supply = <&vdd33a>;
+		reg-io-width = <4>;
+		smsc,save-mac-address;
+	};
+};

67 lines not on this page · raw message

new file mode 100644
index 0000000..75753bb
@@ -0,0 +1,60 @@
+/*
+ * Common support for omap3 EVM boards
+ */
+
+/ {
+	cpus {
+		cpu at 0 {
+			cpu0-supply = <&vcc>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		ledb {
+			label = "omap3evm::ledb";
+			gpios = <&twl_gpio 19 GPIO_ACTIVE_HIGH>; /* LEDB */
+			linux,default-trigger = "default-on";
+		};
+	};
+};
+
+&i2c1 {
+	clock-frequency = <2600000>;
+
+	twl: twl at 48 {
+		reg = <0x48>;
+		interrupts = <7>; /* SYS_NIRQ cascaded to intc */
+		interrupt-parent = <&intc>;
+	};
+};
+
+#include "twl4030.dtsi"
+#include "twl4030_omap3.dtsi"
+
+&i2c2 {
+	clock-frequency = <400000>;
+};
+
+&i2c3 {
+	clock-frequency = <400000>;
+
+	/*
+	 * TVP5146 Video decoder-in for analog input support.
+	 */
+	tvp5146 at 5c {
+		compatible = "ti,tvp5146m2";
+		reg = <0x5c>;
+	};
+};
+
+&twl_gpio {
+	ti,use-leds;
+};
+
+&usb_otg_hs {
+	interface-type = <0>;
+	usb-phy = <&usb2_phy>;
+	mode = <3>;
+	power = <50>;
+};

70 lines not on this page · raw message

index 802720e..3c4e105 100644
@@ -172,6 +172,7 @@ dtb-$(CONFIG_ARCH_OMAP2PLUS) += omap2420-h4.dtb \
 	omap3-devkit8000.dtb \
 	omap3-beagle-xm.dtb \
 	omap3-evm.dtb \
+	omap3-evm-37xx.dtb \
 	omap3-tobi.dtb \
 	omap3-igep0020.dtb \
 	omap3-igep0030.dtb \

146 lines not on this page · raw message

index 75753bb..0020b1d 100644
@@ -2,6 +2,8 @@
  * Common support for omap3 EVM boards
  */
 
+#include "omap-gpmc-smsc911x.dtsi"
+
 / {
 	cpus {
 		cpu at 0 {

@@ -17,6 +19,19 @@
 			linux,default-trigger = "default-on";
 		};
 	};
+
+	wl12xx_vmmc: wl12xx_vmmc {
+		pinctrl-names = "default";
+		pinctrl-0 = <&wl12xx_gpio>;
+		compatible = "regulator-fixed";
+		regulator-name = "vwl1271";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		gpio = <&gpio5 22 0>;	/* gpio150 */
+		startup-delay-us = <70000>;
+		enable-active-high;
+		vin-supply = <&vmmc2>;
+	};
 };
 
 &i2c1 {

@@ -48,6 +63,19 @@
 	};
 };
 
+&mmc1 {
+	vmmc-supply = <&vmmc1>;
+	vmmc_aux-supply = <&vsim>;
+	bus-width = <8>;
+};
+
+&mmc2 {
+	vmmc-supply = <&wl12xx_vmmc>;
+	non-removable;
+	bus-width = <4>;
+	cap-power-off-card;
+};
+
 &twl_gpio {
 	ti,use-leds;
 };

@@ -58,3 +86,11 @@
 	mode = <3>;
 	power = <50>;
 };
+
+&gpmc {
+	ethernet at gpmc {
+		interrupt-parent = <&gpio6>;
+		interrupts = <16 8>;
+		reg = <5 0 0xff>;
+	};
+};

@@ -94,7 +94,7 @@
 		 <5 0 0x2c000000 0x01000000>;
 
 	nand at 0,0 {
-		linux,mtd-name= "micron,mt29c4g96maz";
+		linux,mtd-name= "hynix,h8kds0un0mer-4em";
 		reg = <0 0 0>;
 		nand-bus-width = <16>;
 		ti,nand-ecc-opt = "bch8";

@@ -118,24 +118,24 @@
 		#size-cells = <1>;
 
 		partition at 0 {
-			label = "SPL";
-			reg = <0 0x100000>;
+			label = "X-Loader";
+			reg = <0 0x80000>;
 		};
 		partition at 0x80000 {
 			label = "U-Boot";
-			reg = <0x100000 0x180000>;
+			reg = <0x80000 0x1c0000>;
 		};
 		partition at 0x1c0000 {
 			label = "Environment";
-			reg = <0x280000 0x100000>;
+			reg = <0x240000 0x40000>;
 		};
 		partition at 0x280000 {
 			label = "Kernel";
-			reg = <0x380000 0x300000>;
+			reg = <0x280000 0x500000>;
 		};
 		partition at 0x780000 {
 			label = "Filesystem";
-			reg = <0x680000 0x1f980000>;
+			reg = <0x780000 0x1f880000>;
 		};
 	};
 

index 3c4e105..ce332c8 100644
@@ -176,6 +176,7 @@ dtb-$(CONFIG_ARCH_OMAP2PLUS) += omap2420-h4.dtb \
 	omap3-tobi.dtb \
 	omap3-igep0020.dtb \
 	omap3-igep0030.dtb \
+	omap3-zoom3.dtb \
 	omap4-panda.dtb \
 	omap4-panda-a4.dtb \
 	omap4-panda-es.dtb \

new file mode 100644
index 0000000..b0ee342
@@ -0,0 +1,33 @@
+/*
+ * Common features on the Zoom debug board
+ */
+
+#include "omap-gpmc-smsc911x.dtsi"
+
+&gpmc {
+	ranges = <3 0 0x10000000 0x00000400>,
+		 <7 0 0x2c000000 0x01000000>;
+
+	/*
+	 * Four port TL16CP754C serial port on GPMC,
+	 * they probably share the same GPIO IRQ
+	 * REVISIT: Add timing support from slls644g.pdf
+	 */
+	8250 at 3,0 {
+		compatible = "ns16550a";
+		reg = <3 0 0x100>;
+		bank-width = <2>;
+		reg-shift = <1>;
+		reg-io-width = <1>;
+		interrupt-parent = <&gpio4>;
+		interrupts = <6 IRQ_TYPE_EDGE_RISING>;	/* gpio102 */
+		clock-frequency = <1843200>;
+		current-speed = <115200>;
+	};
+
+	ethernet at gpmc {
+		reg = <7 0 0xff>;
+		interrupt-parent = <&gpio5>;
+		interrupts = <30 IRQ_TYPE_LEVEL_LOW>;	/* gpio158 */
+	};
+};

217 lines not on this page · raw message

index f6a1db1..91a65b3 100644
@@ -256,12 +256,6 @@ config MACH_OVERO
 	default y
 	select OMAP_PACKAGE_CBB
 
-config MACH_OMAP3EVM
-	bool "OMAP 3530 EVM board"
-	depends on ARCH_OMAP3
-	default y
-	select OMAP_PACKAGE_CBB
-
 config MACH_OMAP3517EVM
 	bool "OMAP3517/ AM3517 EVM board"
 	depends on ARCH_OMAP3

index f8d4a1b..7be6e3a 100644
@@ -242,7 +242,6 @@ obj-$(CONFIG_MACH_OMAP_LDP)		+= board-ldp.o
 obj-$(CONFIG_MACH_OMAP3530_LV_SOM)      += board-omap3logic.o
 obj-$(CONFIG_MACH_OMAP3_TORPEDO)        += board-omap3logic.o
 obj-$(CONFIG_MACH_OVERO)		+= board-overo.o
-obj-$(CONFIG_MACH_OMAP3EVM)		+= board-omap3evm.o
 obj-$(CONFIG_MACH_OMAP3_PANDORA)	+= board-omap3pandora.o
 obj-$(CONFIG_MACH_OMAP_3430SDP)		+= board-3430sdp.o
 obj-$(CONFIG_MACH_NOKIA_N8X0)		+= board-n8x0.o

index 91a65b3..216154d 100644
@@ -317,20 +317,6 @@ config MACH_NOKIA_RX51
 	default y
 	select OMAP_PACKAGE_CBB
 
-config MACH_OMAP_ZOOM2
-	bool "OMAP3 Zoom2 board"
-	depends on ARCH_OMAP3
-	default y
-	select OMAP_PACKAGE_CBB
-	select REGULATOR_FIXED_VOLTAGE if REGULATOR
-
-config MACH_OMAP_ZOOM3
-	bool "OMAP3630 Zoom3 board"
-	depends on ARCH_OMAP3
-	default y
-	select OMAP_PACKAGE_CBP
-	select REGULATOR_FIXED_VOLTAGE if REGULATOR
-
 config MACH_CM_T35
 	bool "CompuLab CM-T35/CM-T3730 modules"
 	depends on ARCH_OMAP3

@@ -366,12 +352,6 @@ config MACH_SBC3530
 	default y
 	select OMAP_PACKAGE_CUS
 
-config MACH_OMAP_3630SDP
-	bool "OMAP3630 SDP board"
-	depends on ARCH_OMAP3
-	default y
-	select OMAP_PACKAGE_CBP
-
 config MACH_TI8168EVM
 	bool "TI8168 Evaluation Module"
 	depends on SOC_TI81XX

index 7be6e3a..9d78b49 100644
@@ -249,15 +249,6 @@ obj-$(CONFIG_MACH_NOKIA_RM680)		+= board-rm680.o sdram-nokia.o
 obj-$(CONFIG_MACH_NOKIA_RX51)		+= board-rx51.o sdram-nokia.o
 obj-$(CONFIG_MACH_NOKIA_RX51)		+= board-rx51-peripherals.o
 obj-$(CONFIG_MACH_NOKIA_RX51)		+= board-rx51-video.o
-obj-$(CONFIG_MACH_OMAP_ZOOM2)		+= board-zoom.o board-zoom-peripherals.o
-obj-$(CONFIG_MACH_OMAP_ZOOM2)		+= board-zoom-display.o
-obj-$(CONFIG_MACH_OMAP_ZOOM2)		+= board-zoom-debugboard.o
-obj-$(CONFIG_MACH_OMAP_ZOOM3)		+= board-zoom.o board-zoom-peripherals.o
-obj-$(CONFIG_MACH_OMAP_ZOOM3)		+= board-zoom-display.o
-obj-$(CONFIG_MACH_OMAP_ZOOM3)		+= board-zoom-debugboard.o
-obj-$(CONFIG_MACH_OMAP_3630SDP)		+= board-3630sdp.o
-obj-$(CONFIG_MACH_OMAP_3630SDP)		+= board-zoom-peripherals.o
-obj-$(CONFIG_MACH_OMAP_3630SDP)		+= board-zoom-display.o
 obj-$(CONFIG_MACH_CM_T35)		+= board-cm-t35.o
 obj-$(CONFIG_MACH_CM_T3517)		+= board-cm-t3517.o
 obj-$(CONFIG_MACH_IGEP0020)		+= board-igep0020.o