hw/gpio/max7310.c : add output register property and update the outputports level when necessary
PATCH 1/1 hw/gpio/max7310.c : add output register property and update the outputports level when necessary
From: Zhouy <[email protected]>
To: [email protected]
Date: Fri, 11 Oct 2013 15:54:47 -0400
Subject: [PATCH 1/1] add output register property and update the
outputports level when necessary
--- qemu-master/hw/gpio/max7310.c | 33 ++++++++++++++++++++++----------- 1 files changed, 22 insertions(+), 11 deletions(-)
qemu-master/hw/gpio/max7310.c +16 -0
@@ -19,10 +19,25 @@ typedef struct {uint8_t polarity;uint8_t status;uint8_t command; +uint8_t output;qemu_irq handler[8 ];qemu_irq *gpio_in; } MAX7310State; +/*this function to update outputports level*/ +static void max7310_update (MAX7310State *s) +{ +uint8_t diff =0 ; +uint8_t line =0 ; +for (diff = (s->output ^ s->level) & ~s->direction; diff; + diff &= ~(1 << line)) { + line =ffs (diff) -1 ; +if (s->handler[line]) { +qemu_set_irq (s->handler[line], (s->output >> line) &1 ); + } + } + s->level = (s->level & s->direction) | (s->level & ~s->direction); +} +static void max7310_reset (DeviceState *dev) {
MAX7310State *s = FROM_I2C_SLAVE(MAX7310State, I2C_SLAVE(dev));
@@ -31,6 +46,8 @@ static void max7310_reset(DeviceState *dev)
s->polarity = 0xf0;
s->status = 0x01;
s->command = 0x00;+ s->output = 0x00;
+ max7310_update(s);
}
static int max7310_rx(I2CSlave *i2c)
@@ -43,7 +60,7 @@ static int max7310_rx(I2CSlave *i2c)
break;
case 0x01: /* Output port */
- return s->level & ~s->direction;
+ return s->output;
break;
case 0x02: /* Polarity inversion */
@@ -71,8 +88,6 @@ static int max7310_rx(I2CSlave *i2c)
static int max7310_tx(I2CSlave *i2c, uint8_t data)
{
MAX7310State *s = (MAX7310State *) i2c;- uint8_t diff;
- int line;
if (s->len ++ > 1) { #ifdef VERBOSE
@@ -89,13 +104,8 @@ static int max7310_tx(I2CSlave *i2c, uint8_t data)
switch (s->command) {
case 0x01: /* Output port */- for (diff = (data ^ s->level) & ~s->direction; diff;
- diff &= ~(1 << line)) {
- line = ffs(diff) - 1;
- if (s->handler[line])
- qemu_set_irq(s->handler[line], (data >> line) & 1);
- }
- s->level = (s->level & s->direction) | (data & ~s->direction);
+ s->output = data;
+ max7310_update(s);
break;
case 0x02: /* Polarity inversion */
@@ -103,8 +113,8 @@ static int max7310_tx(I2CSlave *i2c, uint8_t data)
break;
case 0x03: /* Configuration */
- s->level &= ~(s->direction ^ data);
s->direction = data;
+ max7310_update(s);
break;
case 0x04: /* Timeout */
@@ -156,6 +166,7 @@ static const VMStateDescription vmstate_max7310 = {
VMSTATE_UINT8(polarity, MAX7310State),
VMSTATE_UINT8(status, MAX7310State),
VMSTATE_UINT8(command, MAX7310State),
+ VMSTATE_UINT8(output, MAX7310State),
VMSTATE_I2C_SLAVE(i2c, MAX7310State),
VMSTATE_END_OF_LIST()
}Signature · 18 lines
1.7.6 -------------- A new email address of FJWAN is launched from Apr.1 2007. The updated address is: [email protected] -------------------------------------------------- Zhou Yuan Nanjing Fujitsu Nanda Software Tech. Co., Ltd.(FNST) No. 6 Wenzhu Road, Nanjing, 210012, China TEL:+86+25-86630566-9555 FUJITSU INTERNAL:7998-9555 FAX:+86+25-83317685 EMail:[email protected] -------------------------------------------------- This communication is for use by the intended recipient(s) only and may contain information that is privileged, confidential and exempt from disclosure under applicable law. If you are not an intended recipient of this communication, you are hereby notified that any dissemination, distribution or copying hereof is strictly prohibited. If you have received this communication in error, please notify me by reply e-mail, permanently delete this communication from your system, and destroy any hard copies you may have printed. [email protected] 16:34:14
PATCH 1/1 hw/gpio/max7310.c : add the reset-pin in Max7310 and the GPIO will be reseted by the reset signal(active low) when necessary
From: zhouy <[email protected]>
Date: Sun, 17 Nov 2013 09:24:38 -0500
Subject: [PATCH 4/4] add the reset-pin in Max7310 and the GPIO will be
reseted by the reset signal(active low) when necessary
---
qemu-master/hw/gpio/max7310.c | 8 ++++++-- 1 files changed, 6 insertions(+), 2 deletions(-)
qemu-master/hw/gpio/max7310.c +6 -2
@@ -166,7 +166,11 @@ static void max7310_gpio_set(void *opaque, int line, int level)MAX7310State *s = (MAX7310State *) opaque;if (line >=ARRAY_SIZE (s->handler) || line <0 )hw_error ("bad GPIO line" ); - +/* add reset-pin (active low) as the 9th gpio-in*/ +if (line ==8 && level ==0 ) { +max7310_reset (s); +return ; + }if (level) s->level |= s->direction & (1 << line);else
@@ -179,7 +183,7 @@ static int max7310_init(I2CSlave *i2c) {MAX7310State *s =FROM_I2C_SLAVE (MAX7310State, i2c); -qdev_init_gpio_in (&i2c->qdev, max7310_gpio_set,8 ); +qdev_init_gpio_in (&i2c->qdev, max7310_gpio_set,9 );qdev_init_gpio_out (&i2c->qdev, s->handler,8 );return 0 ;
Signature · 6 lines
1.7.6 -------------- A new email address of FJWAN is launched from Apr.1 2007. The updated address is: [email protected] --------------------------------------------------