spi: mxc: Fix data loss for non aligned write buffers.
Subsystems (2)
PATCH 1/1 spi: mxc: Fix data loss for non aligned write buffers.
When writing buffers that are not 32 bit aligned data loss occurs.
This can also occur when the total transfer size is not a multiple of 4 bytes since the extra bytes are written first causing the rest to be unaligned.
This can be seen by writing to SPI flash a 57 byte file containing 00 01 .. 38:
U-Boot > dhcp data.bin
...
Bytes transferred = 57 (39 hex)
U-Boot > md.b $loadaddr
72000000: 00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f ................
72000010: 10 11 12 13 14 15 16 17 18 19 1a 1b 1c 1d 1e 1f ................
72000020: 20 21 22 23 24 25 26 27 28 29 2a 2b 2c 2d 2e 2f !"#$%&'()*+,-./
72000030: 30 31 32 33 34 35 36 37 38 ff ff ff ff ff ff ff 012345678.......
U-Boot > sf write $loadaddr 0 $filesize
U-Boot > mw.b $loadaddr ff 100
U-Boot > sf read $loadaddr 0 100
U-Boot > md.b $loadaddr
72000000: 00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f ................
72000010: 10 11 12 13 14 15 16 17 18 19 1a 1b 1c 1d 1e 1f ................
72000020: 20 21 22 23 24 29 2a 2b 2c 31 32 33 34 ff ff ff !"#$)*+,1234...
72000030: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ................
[bytes 25-28, 2d-30, 35-38 are missing]
Activating debug in the write command gave:spi_xchg_single: bitlen 256 dout 0x72000000 din 0x0 Sending SPI 0x10203
Sending SPI 0x4050607
Sending SPI 0x8090a0b
Sending SPI 0xc0d0e0f
Sending SPI 0x10111213
Sending SPI 0x14151617
Sending SPI 0x18191a1b
Sending SPI 0x1c1d1e1f
SPI Rx: 0xffffffff 0xffffffff
...
SPI Rx: 0xffffffff 0xffffffffspi_xchg_single: bitlen 200 dout 0x72000020 din 0x0 Sending SPI 0x20
Sending SPI 0x21222324
Sending SPI 0x292a2b2c <=== What happened to 25262728?
Sending SPI 0x31323334
Sending SPI 0xffffffff
...
SF: program success 57 bytes @ 0x0
The problem was that the pointer was being incremented twice for the non aligned case.
--- drivers/spi/mxc_spi.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/spi/mxc_spi.c +1 -1
@@ -274,8 +274,8 @@ int spi_xchg_single(struct spi_slave *slave, unsigned int bitlen, }else { data = *(u32 *)dout; data =cpu_to_be32 (data); + dout +=4 ; } - dout +=4 ; }debug ("Sending SPI 0x%x\n" , data);reg_write (®s->txdata, data);
PATCH 1/1 spi: mxc: Fix data loss for non aligned write buffers.
Hi,
Quoted 40 lines · Martin Fuzzey
When writing buffers that are not 32 bit aligned data loss occurs.
This can also occur when the total transfer size is not a multiple of 4 bytes since the extra bytes are written first causing the rest to be unaligned.
This can be seen by writing to SPI flash a 57 byte file containing 00 01 .. 38:
U-Boot > dhcp data.bin
...
Bytes transferred = 57 (39 hex)
U-Boot > md.b $loadaddr
72000000: 00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f ................
72000010: 10 11 12 13 14 15 16 17 18 19 1a 1b 1c 1d 1e 1f ................
72000020: 20 21 22 23 24 25 26 27 28 29 2a 2b 2c 2d 2e 2f !"#$%&'()*+,-./
72000030: 30 31 32 33 34 35 36 37 38 ff ff ff ff ff ff ff 012345678.......
U-Boot > sf write $loadaddr 0 $filesizeU-Boot > mw.b $loadaddr ff 100
U-Boot > sf read $loadaddr 0 100
U-Boot > md.b $loadaddr
72000000: 00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f ................
72000010: 10 11 12 13 14 15 16 17 18 19 1a 1b 1c 1d 1e 1f ................
72000020: 20 21 22 23 24 29 2a 2b 2c 31 32 33 34 ff ff ff !"#$)*+,1234...
72000030: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ................[bytes 25-28, 2d-30, 35-38 are missing]
Activating debug in the write command gave:
spi_xchg_single: bitlen 256 dout0x72000000din0x0Sending SPI0x10203
Sending SPI0x4050607
Sending SPI0x8090a0b
Sending SPI0xc0d0e0f
Sending SPI0x10111213
Sending SPI0x14151617
Sending SPI0x18191a1b
Sending SPI0x1c1d1e1f
SPI Rx:0xffffffff0xffffffff
...
SPI Rx:0xffffffff0xffffffff
Quoted 8 lines
spi_xchg_single: bitlen 200 dout0x72000020din0x0Sending SPI0x20
Sending SPI0x21222324
Sending SPI0x292a2b2c<=== What happened to 25262728? Sending SPI0x31323334
Sending SPI0xffffffff
...
SF: program success 57 bytes @0x0
Thanks for your log, for showing the exact issues.
Quoted 15 lines
The problem was that the pointer was being incremented twice for the non aligned case.
Signed-off-by Martin Fuzzey <[email protected]>--- drivers/spi/mxc_spi.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)drivers/spi/mxc_spi.c +0
-0
drivers/spi/mxc_spi.c int spi_xchg_single(struct spi_slave *slave, unsigned int bitlen, · line 281
Quoted 9 lines
drivers/spi/mxc_spi.c +1
-1@@ -274,8 +274,8 @@ int spi_xchg_single(struct spi_slave *slave, unsigned int bitlen, }else { data = *(u32 *)dout; data =cpu_to_be32 (data); + dout +=4 ; } - dout +=4 ; }debug ("Sending SPI 0x%x\n" , data);reg_write (®s->txdata, data);
This patch pushed on master, please check it on
http://git.denx.de/?p=u-boot.git;a=commitdiff;h=6d5ce1bd0048617d48c05de1a84fae8696081127
Signature · 8 lines
Thanks, Jagan. -------- Jagannadha Sutradharudu Teki, E: jagannadh.teki at gmail.com, P: +91-9676773388 Engineer - System Software Hacker U-boot - SPI Custodian and Zynq APSOC Ln: http://www.linkedin.com/in/jaganteki
PATCH 1/1 spi: mxc: Fix data loss for non aligned write buffers.
Hi Jagan,
Quoted 51 lines · Jagan Teki
Hi,
Quoted 40 lines · Martin Fuzzey
When writing buffers that are not 32 bit aligned data loss occurs.
This can also occur when the total transfer size is not a multiple of 4 bytes since the extra bytes are written first causing the rest to be unaligned.
This can be seen by writing to SPI flash a 57 byte file containing 00 01 .. 38:
U-Boot > dhcp data.bin
...
Bytes transferred = 57 (39 hex)
U-Boot > md.b $loadaddr
72000000: 00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f ................
72000010: 10 11 12 13 14 15 16 17 18 19 1a 1b 1c 1d 1e 1f ................
72000020: 20 21 22 23 24 25 26 27 28 29 2a 2b 2c 2d 2e 2f !"#$%&'()*+,-./
72000030: 30 31 32 33 34 35 36 37 38 ff ff ff ff ff ff ff 012345678.......
U-Boot > sf write $loadaddr 0 $filesizeU-Boot > mw.b $loadaddr ff 100
U-Boot > sf read $loadaddr 0 100
U-Boot > md.b $loadaddr
72000000: 00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f ................
72000010: 10 11 12 13 14 15 16 17 18 19 1a 1b 1c 1d 1e 1f ................
72000020: 20 21 22 23 24 29 2a 2b 2c 31 32 33 34 ff ff ff !"#$)*+,1234...
72000030: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ................[bytes 25-28, 2d-30, 35-38 are missing]
Activating debug in the write command gave:
spi_xchg_single: bitlen 256 dout0x72000000din0x0Sending SPI0x10203
Sending SPI0x4050607
Sending SPI0x8090a0b
Sending SPI0xc0d0e0f
Sending SPI0x10111213
Sending SPI0x14151617
Sending SPI0x18191a1b
Sending SPI0x1c1d1e1f
SPI Rx:0xffffffff0xffffffff
...
SPI Rx:0xffffffff0xffffffffQuoted 8 lines
spi_xchg_single: bitlen 200 dout0x72000020din0x0Sending SPI0x20
Sending SPI0x21222324
Sending SPI0x292a2b2c<=== What happened to 25262728? Sending SPI0x31323334
Sending SPI0xffffffff
...
SF: program success 57 bytes @0x0
Quoted 1 line
Thanks for your log, for showing the exact issues.
Agreed, but I think this log could go in a comment below the '---' line, so that the commit message focuses on describing what the patch does, rather than how it was found out necessary.
Amicalement,
Signature · 1 line
Albert.
PATCH 1/1 spi: mxc: Fix data loss for non aligned write buffers.
Hi Amicalement,
Quoted 56 lines · Albert ARIBAUD
Hi Jagan,
Quoted 51 lines · Jagan Teki
Hi,
Quoted 48 lines · Martin Fuzzey
When writing buffers that are not 32 bit aligned data loss occurs.
This can also occur when the total transfer size is not a multiple of 4 bytes since the extra bytes are written first causing the rest to be unaligned.
This can be seen by writing to SPI flash a 57 byte file containing 00 01 .. 38:
U-Boot > dhcp data.bin
...
Bytes transferred = 57 (39 hex)
U-Boot > md.b $loadaddr
72000000: 00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f ................
72000010: 10 11 12 13 14 15 16 17 18 19 1a 1b 1c 1d 1e 1f ................
72000020: 20 21 22 23 24 25 26 27 28 29 2a 2b 2c 2d 2e 2f !"#$%&'()*+,-./
72000030: 30 31 32 33 34 35 36 37 38 ff ff ff ff ff ff ff 012345678.......
U-Boot > sf write $loadaddr 0 $filesizeU-Boot > mw.b $loadaddr ff 100
U-Boot > sf read $loadaddr 0 100
U-Boot > md.b $loadaddr
72000000: 00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f ................
72000010: 10 11 12 13 14 15 16 17 18 19 1a 1b 1c 1d 1e 1f ................
72000020: 20 21 22 23 24 29 2a 2b 2c 31 32 33 34 ff ff ff !"#$)*+,1234...
72000030: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ................[bytes 25-28, 2d-30, 35-38 are missing]
Activating debug in the write command gave:
spi_xchg_single: bitlen 256 dout0x72000000din0x0Sending SPI0x10203
Sending SPI0x4050607
Sending SPI0x8090a0b
Sending SPI0xc0d0e0f
Sending SPI0x10111213
Sending SPI0x14151617
Sending SPI0x18191a1b
Sending SPI0x1c1d1e1f
SPI Rx:0xffffffff0xffffffff
...
SPI Rx:0xffffffff0xffffffffspi_xchg_single: bitlen 200 dout0x72000020din0x0Sending SPI0x20
Sending SPI0x21222324
Sending SPI0x292a2b2c<=== What happened to 25262728? Sending SPI0x31323334
Sending SPI0xffffffff
...
SF: program success 57 bytes @0x0
Quoted 5 lines
Quoted 1 line
Thanks for your log, for showing the exact issues.
Agreed, but I think this log could go in a comment below the '---' line, so that the commit message focuses on describing what the patch does, rather than how it was found out necessary.
I too thought the same, but the commit is already in master, any possibility to alter?
Signature · 8 lines
Thanks, Jagan. -------- Jagannadha Sutradharudu Teki, E: jagannadh.teki at gmail.com, P: +91-9676773388 Engineer - System Software Hacker U-boot - SPI Custodian and Zynq APSOC Ln: http://www.linkedin.com/in/jaganteki
PATCH 1/1 spi: mxc: Fix data loss for non aligned write buffers.
Hi Jagan,
Quoted 60 lines · Jagan Teki
Hi Amicalement,
Quoted 56 lines · Albert ARIBAUD
Hi Jagan,
Quoted 51 lines · Jagan Teki
Hi,
Quoted 48 lines · Martin Fuzzey
When writing buffers that are not 32 bit aligned data loss occurs.
This can also occur when the total transfer size is not a multiple of 4 bytes since the extra bytes are written first causing the rest to be unaligned.
This can be seen by writing to SPI flash a 57 byte file containing 00 01 .. 38:
U-Boot > dhcp data.bin
...
Bytes transferred = 57 (39 hex)
U-Boot > md.b $loadaddr
72000000: 00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f ................
72000010: 10 11 12 13 14 15 16 17 18 19 1a 1b 1c 1d 1e 1f ................
72000020: 20 21 22 23 24 25 26 27 28 29 2a 2b 2c 2d 2e 2f !"#$%&'()*+,-./
72000030: 30 31 32 33 34 35 36 37 38 ff ff ff ff ff ff ff 012345678.......
U-Boot > sf write $loadaddr 0 $filesizeU-Boot > mw.b $loadaddr ff 100
U-Boot > sf read $loadaddr 0 100
U-Boot > md.b $loadaddr
72000000: 00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f ................
72000010: 10 11 12 13 14 15 16 17 18 19 1a 1b 1c 1d 1e 1f ................
72000020: 20 21 22 23 24 29 2a 2b 2c 31 32 33 34 ff ff ff !"#$)*+,1234...
72000030: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ................[bytes 25-28, 2d-30, 35-38 are missing]
Activating debug in the write command gave:
spi_xchg_single: bitlen 256 dout0x72000000din0x0Sending SPI0x10203
Sending SPI0x4050607
Sending SPI0x8090a0b
Sending SPI0xc0d0e0f
Sending SPI0x10111213
Sending SPI0x14151617
Sending SPI0x18191a1b
Sending SPI0x1c1d1e1f
SPI Rx:0xffffffff0xffffffff
...
SPI Rx:0xffffffff0xffffffffspi_xchg_single: bitlen 200 dout0x72000020din0x0Sending SPI0x20
Sending SPI0x21222324
Sending SPI0x292a2b2c<=== What happened to 25262728? Sending SPI0x31323334
Sending SPI0xffffffff
...
SF: program success 57 bytes @0x0
Quoted 8 lines
Quoted 5 lines
Quoted 1 line
Thanks for your log, for showing the exact issues.
Agreed, but I think this log could go in a comment below the '---' line, so that the commit message focuses on describing what the patch does, rather than how it was found out necessary.
I too thought the same, but the commit is already in master, any possibility to alter?
Er... Martin's patch is already in patchwork as 283794, but its state is still "New" with no delegate, and I don't see it in any of the repos I usually read, nor does it appear on u-boot-spi. Where do you see it "in master" exactly?
Besides, it is less than 24 hours old; this is not enough time for review, and therefore, it should not be accepted yet.
Amicalement,
Signature · 1 line
Albert.
PATCH 1/1 spi: mxc: Fix data loss for non aligned write buffers.
Hi Albert,
Quoted 74 lines · Albert ARIBAUD
Hi Jagan,
Quoted 60 lines · Jagan Teki
Hi Amicalement,
Quoted 56 lines · Albert ARIBAUD
Hi Jagan,
Quoted 51 lines · Jagan Teki
Hi,
Quoted 48 lines · Martin Fuzzey
When writing buffers that are not 32 bit aligned data loss occurs.
This can also occur when the total transfer size is not a multiple of 4 bytes since the extra bytes are written first causing the rest to be unaligned.
This can be seen by writing to SPI flash a 57 byte file containing 00 01 .. 38:
U-Boot > dhcp data.bin
...
Bytes transferred = 57 (39 hex)
U-Boot > md.b $loadaddr
72000000: 00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f ................
72000010: 10 11 12 13 14 15 16 17 18 19 1a 1b 1c 1d 1e 1f ................
72000020: 20 21 22 23 24 25 26 27 28 29 2a 2b 2c 2d 2e 2f !"#$%&'()*+,-./
72000030: 30 31 32 33 34 35 36 37 38 ff ff ff ff ff ff ff 012345678.......
U-Boot > sf write $loadaddr 0 $filesizeU-Boot > mw.b $loadaddr ff 100
U-Boot > sf read $loadaddr 0 100
U-Boot > md.b $loadaddr
72000000: 00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f ................
72000010: 10 11 12 13 14 15 16 17 18 19 1a 1b 1c 1d 1e 1f ................
72000020: 20 21 22 23 24 29 2a 2b 2c 31 32 33 34 ff ff ff !"#$)*+,1234...
72000030: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ................[bytes 25-28, 2d-30, 35-38 are missing]
Activating debug in the write command gave:
spi_xchg_single: bitlen 256 dout0x72000000din0x0Sending SPI0x10203
Sending SPI0x4050607
Sending SPI0x8090a0b
Sending SPI0xc0d0e0f
Sending SPI0x10111213
Sending SPI0x14151617
Sending SPI0x18191a1b
Sending SPI0x1c1d1e1f
SPI Rx:0xffffffff0xffffffff
...
SPI Rx:0xffffffff0xffffffffspi_xchg_single: bitlen 200 dout0x72000020din0x0Sending SPI0x20
Sending SPI0x21222324
Sending SPI0x292a2b2c<=== What happened to 25262728? Sending SPI0x31323334
Sending SPI0xffffffff
...
SF: program success 57 bytes @0x0Quoted 8 lines
Quoted 5 lines
Quoted 1 line
Thanks for your log, for showing the exact issues.
Agreed, but I think this log could go in a comment below the '---' line, so that the commit message focuses on describing what the patch does, rather than how it was found out necessary.
I too thought the same, but the commit is already in master, any possibility to alter?
Quoted 7 lines
Er... Martin's patch is already in patchwork as 283794, but its state is still "New" with no delegate, and I don't see it in any of the repos I usually read, nor does it appear on u-boot-spi. Where do you see it "in master" exactly?
Besides, it is less than 24 hours old; this is not enough time for review, and therefore, it should not be accepted yet.
I got the similar patch from Timo Herbrecher couple of weeks back, I just reviewed and sent back to v3 before apllied on u-boot-spi.
Yesterday I sent this patch as part of spi PR.
You can find the patch in master:
http://git.denx.de/?p=u-boot.git;a=commitdiff;h=6d5ce1bd0048617d48c05de1a84fae8696081127
Please let me know you still have any concerns, I agreed your concern that the commit message
have enough info for this fix. But right know i think we can't do as it's part of master.
If any possibility to alter the commit msg, please let me know.
Signature · 8 lines
Thanks, Jagan. -------- Jagannadha Sutradharudu Teki, E: jagannadh.teki at gmail.com, P: +91-9676773388 Engineer - System Software Hacker U-boot - SPI Custodian and Zynq APSOC Ln: http://www.linkedin.com/in/jaganteki
PATCH 1/1 spi: mxc: Fix data loss for non aligned write buffers.
Quoted 90 lines · Jagan Teki
Hi Albert,
Quoted 71 lines · Albert ARIBAUD
Hi Jagan,
Quoted 60 lines · Jagan Teki
Hi Amicalement,
Quoted 56 lines · Albert ARIBAUD
Hi Jagan,
Quoted 51 lines · Jagan Teki
Hi,
Quoted 48 lines · Martin Fuzzey
When writing buffers that are not 32 bit aligned data loss occurs.
This can also occur when the total transfer size is not a multiple of 4 bytes since the extra bytes are written first causing the rest to be unaligned.
This can be seen by writing to SPI flash a 57 byte file containing 00 01 .. 38:
U-Boot > dhcp data.bin
...
Bytes transferred = 57 (39 hex)
U-Boot > md.b $loadaddr
72000000: 00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f ................
72000010: 10 11 12 13 14 15 16 17 18 19 1a 1b 1c 1d 1e 1f ................
72000020: 20 21 22 23 24 25 26 27 28 29 2a 2b 2c 2d 2e 2f !"#$%&'()*+,-./
72000030: 30 31 32 33 34 35 36 37 38 ff ff ff ff ff ff ff 012345678.......
U-Boot > sf write $loadaddr 0 $filesizeU-Boot > mw.b $loadaddr ff 100
U-Boot > sf read $loadaddr 0 100
U-Boot > md.b $loadaddr
72000000: 00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f ................
72000010: 10 11 12 13 14 15 16 17 18 19 1a 1b 1c 1d 1e 1f ................
72000020: 20 21 22 23 24 29 2a 2b 2c 31 32 33 34 ff ff ff !"#$)*+,1234...
72000030: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ................[bytes 25-28, 2d-30, 35-38 are missing]
Activating debug in the write command gave:
spi_xchg_single: bitlen 256 dout0x72000000din0x0Sending SPI0x10203
Sending SPI0x4050607
Sending SPI0x8090a0b
Sending SPI0xc0d0e0f
Sending SPI0x10111213
Sending SPI0x14151617
Sending SPI0x18191a1b
Sending SPI0x1c1d1e1f
SPI Rx:0xffffffff0xffffffff
...
SPI Rx:0xffffffff0xffffffffspi_xchg_single: bitlen 200 dout0x72000020din0x0Sending SPI0x20
Sending SPI0x21222324
Sending SPI0x292a2b2c<=== What happened to 25262728? Sending SPI0x31323334
Sending SPI0xffffffff
...
SF: program success 57 bytes @0x0Quoted 6 lines
Quoted 4 lines
Quoted 1 line
Thanks for your log, for showing the exact issues.
Agreed, but I think this log could go in a comment below the '---' line, so that the commit message focuses on describing what the patch does, rather than how it was found out necessary.
I too thought the same, but the commit is already in master, any possibility to alter?
Quoted 7 lines
Er... Martin's patch is already in patchwork as 283794, but its state is still "New" with no delegate, and I don't see it in any of the repos I usually read, nor does it appear on u-boot-spi. Where do you see it "in master" exactly?
Besides, it is less than 24 hours old; this is not enough time for review, and therefore, it should not be accepted yet.
I got the similar patch from Timo Herbrecher couple of weeks back, I just reviewed and sent back to v3 before apllied on u-boot-spi.
Yesterday I sent this patch as part of spi PR.
You can find the patch in master:
http://git.denx.de/?p=u-boot.git;a=commitdiff;h=6d5ce1bd0048617d48c05de1a84fae8696081127
Quoted 7 lines
Please let me know you still have any concerns, I agreed your concern that the commit message
have enough info for this fix. But right know i think we can't do as it's part of master.If any possibility to alter the commit msg, please let me know.
Yes looks like two patches doing the same thing.
The one in master is from Timo Herbrecher not me.
I checked git master before sending my patch and it wasn't there yet but didin't check the mailing list archives.
Anyway the code is identical just the commit message changes.
Cheers,
Martin
PATCH 1/1 spi: mxc: Fix data loss for non aligned write buffers.
In reply to Jagan TekiHi Jagan,
Quoted 94 lines · Jagan Teki
Hi Albert,
Quoted 74 lines · Albert ARIBAUD
Hi Jagan,
Quoted 60 lines · Jagan Teki
Hi Amicalement,
Quoted 56 lines · Albert ARIBAUD
Hi Jagan,
Quoted 51 lines · Jagan Teki
Hi,
Quoted 48 lines · Martin Fuzzey
When writing buffers that are not 32 bit aligned data loss occurs.
This can also occur when the total transfer size is not a multiple of 4 bytes since the extra bytes are written first causing the rest to be unaligned.
This can be seen by writing to SPI flash a 57 byte file containing 00 01 .. 38:
U-Boot > dhcp data.bin
...
Bytes transferred = 57 (39 hex)
U-Boot > md.b $loadaddr
72000000: 00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f ................
72000010: 10 11 12 13 14 15 16 17 18 19 1a 1b 1c 1d 1e 1f ................
72000020: 20 21 22 23 24 25 26 27 28 29 2a 2b 2c 2d 2e 2f !"#$%&'()*+,-./
72000030: 30 31 32 33 34 35 36 37 38 ff ff ff ff ff ff ff 012345678.......
U-Boot > sf write $loadaddr 0 $filesizeU-Boot > mw.b $loadaddr ff 100
U-Boot > sf read $loadaddr 0 100
U-Boot > md.b $loadaddr
72000000: 00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f ................
72000010: 10 11 12 13 14 15 16 17 18 19 1a 1b 1c 1d 1e 1f ................
72000020: 20 21 22 23 24 29 2a 2b 2c 31 32 33 34 ff ff ff !"#$)*+,1234...
72000030: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ................[bytes 25-28, 2d-30, 35-38 are missing]
Activating debug in the write command gave:
spi_xchg_single: bitlen 256 dout0x72000000din0x0Sending SPI0x10203
Sending SPI0x4050607
Sending SPI0x8090a0b
Sending SPI0xc0d0e0f
Sending SPI0x10111213
Sending SPI0x14151617
Sending SPI0x18191a1b
Sending SPI0x1c1d1e1f
SPI Rx:0xffffffff0xffffffff
...
SPI Rx:0xffffffff0xffffffffspi_xchg_single: bitlen 200 dout0x72000020din0x0Sending SPI0x20
Sending SPI0x21222324
Sending SPI0x292a2b2c<=== What happened to 25262728? Sending SPI0x31323334
Sending SPI0xffffffff
...
SF: program success 57 bytes @0x0Quoted 8 lines
Quoted 5 lines
Quoted 1 line
Thanks for your log, for showing the exact issues.
Agreed, but I think this log could go in a comment below the '---' line, so that the commit message focuses on describing what the patch does, rather than how it was found out necessary.
I too thought the same, but the commit is already in master, any possibility to alter?
Quoted 7 lines
Er... Martin's patch is already in patchwork as 283794, but its state is still "New" with no delegate, and I don't see it in any of the repos I usually read, nor does it appear on u-boot-spi. Where do you see it "in master" exactly?
Besides, it is less than 24 hours old; this is not enough time for review, and therefore, it should not be accepted yet.
I got the similar patch from Timo Herbrecher couple of weeks back, I just reviewed and sent back to v3 before apllied on u-boot-spi.
Yesterday I sent this patch as part of spi PR.
You can find the patch in master:
http://git.denx.de/?p=u-boot.git;a=commitdiff;h=6d5ce1bd0048617d48c05de1a84fae8696081127
Quoted 6 lines
Please let me know you still have any concerns, I agreed your concern that the commit message
have enough info for this fix. But right know i think we can't do as it's part of master.If any possibility to alter the commit msg, please let me know.
If it's gone in a repo, especially the main one, then you can't roll it back -- BTW Timo's commit message is ok for me.
Amicalement,
Signature · 1 line
Albert.