: serial: 8250_pci: add support for Fintek 4, 8, and 12 port cards
Greg Kroah-Hartman
maintainerPATCH 1/1 : serial: 8250_pci: add support for Fintek 4, 8, and 12 port cards
From: Greg Kroah-Hartman <[email protected]>
This adds support for Fintek's 4, 8, and 12 port PCIE serial cards.
Thanks to Fintek for the sample devices, and the spec needed in order to implement this.
--- drivers/tty/serial/8250/8250_pci.c | 112 +++++++++++++++++++++++++++++++++++++ 1 file changed, 112 insertions(+)
drivers/tty/serial/8250/8250_pci.c +112 -0
@@ -1343,6 +1343,71 @@ pci_brcm_trumanage_setup(struct serial_preturn ret; } +static int pci_fintek_setup (struct serial_private *priv, +const struct pciserial_board *board, +struct uart_8250_port *port,int idx) +{ +struct pci_dev *pdev = priv->dev; +unsigned long base; +unsigned long iobase; +unsigned long ciobase =0 ; +u8 config_base; + +/* +* We are supposed to be able to read these from the PCI config space, +* but the values there don't seem to match what we need to use, so +* just use these hard-coded values for now, as they are correct. +*/ +switch (idx) { +case 0 : iobase =0xe000 ; config_base =0x40 ;break ; +case 1 : iobase =0xe008 ; config_base =0x48 ;break ; +case 2 : iobase =0xe010 ; config_base =0x50 ;break ; +case 3 : iobase =0xe018 ; config_base =0x58 ;break ; +case 4 : iobase =0xe020 ; config_base =0x60 ;break ; +case 5 : iobase =0xe028 ; config_base =0x68 ;break ; +case 6 : iobase =0xe030 ; config_base =0x70 ;break ; +case 7 : iobase =0xe038 ; config_base =0x78 ;break ; +case 8 : iobase =0xe040 ; config_base =0x80 ;break ; +case 9 : iobase =0xe048 ; config_base =0x88 ;break ; +case 10 : iobase =0xe050 ; config_base =0x90 ;break ; +case 11 : iobase =0xe058 ; config_base =0x98 ;break ; +default : +/* Unknown number of ports, get out of here */ +return -EINVAL ; + } + +if (idx <4 ) { + base =pci_resource_start (priv->dev,3 ); + ciobase = (int )(base + (0x8 * idx)); + } + +dev_dbg (&pdev->dev,"%s: idx=%d iobase=0x%lx ciobase=0x%lx config_base=0x%2x\n" , + __func__, idx, iobase, ciobase, config_base); + +/* Enable UART I/O port */ +pci_write_config_byte (pdev, config_base +0x00 ,0x01 ); + +/* Select 128-byte FIFO and 8x FIFO threshold */ +pci_write_config_byte (pdev, config_base +0x01 ,0x33 ); + +/* LSB UART */ +pci_write_config_byte (pdev, config_base +0x04 , (u8)(iobase &0xff )); + +/* MSB UART */ +pci_write_config_byte (pdev, config_base +0x05 , (u8)((iobase &0xff00 ) >>8 )); + +/* irq number, this usually fails, but the spec says to do it anyway. */ +pci_write_config_byte (pdev, config_base +0x06 , pdev->irq); + + port->port.iotype =UPIO_PORT ; + port->port.iobase = iobase; + port->port.mapbase =0 ; + port->port.membase =NULL ; + port->port.regshift =0 ; + +return 0 ; +} +static int skip_tx_en_setup (struct serial_private *priv,const struct pciserial_board *board,struct uart_8250_port *port,int idx)
@@ -2252,6 +2317,27 @@ static struct pci_serial_quirk pci_seria .subdevice = PCI_ANY_ID, .setup = pci_brcm_trumanage_setup, }, + { + .vendor = 0x1c29, + .device = 0x1104, + .subvendor = PCI_ANY_ID, + .subdevice = PCI_ANY_ID, + .setup = pci_fintek_setup, + }, + { + .vendor = 0x1c29, + .device = 0x1108, + .subvendor = PCI_ANY_ID, + .subdevice = PCI_ANY_ID, + .setup = pci_fintek_setup, + }, + { + .vendor = 0x1c29, + .device = 0x1112, + .subvendor = PCI_ANY_ID, + .subdevice = PCI_ANY_ID, + .setup = pci_fintek_setup, + }, /* * Default "match everything" terminator entry
@@ -2449,6 +2535,9 @@ enum pci_board_num_t { pbn_omegapci, pbn_NETMOS9900_2s_115200, pbn_brcm_trumanage, + pbn_fintek_4, + pbn_fintek_8, + pbn_fintek_12, };/*
@@ -3199,6 +3288,24 @@ static struct pciserial_board pci_boards .reg_shift = 2, .base_baud = 115200, }, + [pbn_fintek_4] = { + .num_ports = 4, + .uart_offset = 8, + .base_baud = 115200, + .first_offset = 0x40, + }, + [pbn_fintek_8] = { + .num_ports = 8, + .uart_offset = 8, + .base_baud = 115200, + .first_offset = 0x40, + }, + [pbn_fintek_12] = { + .num_ports = 12, + .uart_offset = 8, + .base_baud = 115200, + .first_offset = 0x40, + }, };static const struct pci_device_id blacklist[] = {
@@ -4916,6 +5023,11 @@ static struct pci_device_id serial_pci_t0 , 0, pbn_exar_XR17V358 }, +/* Fintek PCI serial cards */ + { PCI_DEVICE(0x1c29, 0x1104), .driver_data = pbn_fintek_4 }, + { PCI_DEVICE(0x1c29, 0x1108), .driver_data = pbn_fintek_8 }, + { PCI_DEVICE(0x1c29, 0x1112), .driver_data = pbn_fintek_12 }, +/* * These entries match devices with class COMMUNICATION_SERIAL, * COMMUNICATION_MODEM or COMMUNICATION_MULTISERIAL
Hi Ginger,
如電話中所提的, 可以使用F81504 GPIO來控制F81438 Mode的切換, GPIO register可以從spec page 49看到相關說明, Fintek PCIE to UART programming guide 130601PA.pdf有GPIO register設定方法, 請看附件檔
Best Regards,
Felix Shih
精拓科技股份有限公司
Feature Integration Technology
TEL: 03-5600168 # 812
-----Original Message-----
From: Greg Kroah-Hartman [mailto:[email protected]]
Sent: Friday, October 18, 2013 1:44 AM
To: [email protected]
Cc: [email protected]; PM10 AMANDA YING 尹文婷; PA11 FELIX SHIH 施宏宜
Subject: [PATCH]: serial: 8250_pci: add support for Fintek 4, 8, and 12 port cards
From: Greg Kroah-Hartman <[email protected]>
This adds support for Fintek's 4, 8, and 12 port PCIE serial cards.
Thanks to Fintek for the sample devices, and the spec needed in order to implement this.
--- drivers/tty/serial/8250/8250_pci.c | 112 +++++++++++++++++++++++++++++++++++++ 1 file changed, 112 insertions(+)
drivers/tty/serial/8250/8250_pci.c +65 -0
@@ -1343,6 +1343,71 @@ pci_brcm_trumanage_setup(struct serial_preturn ret; } +static int pci_fintek_setup (struct serial_private *priv, +const struct pciserial_board *board, +struct uart_8250_port *port,int idx) { +struct pci_dev *pdev = priv->dev; +unsigned long base; +unsigned long iobase; +unsigned long ciobase =0 ; +u8 config_base; + +/* +* We are supposed to be able to read these from the PCI config space, +* but the values there don't seem to match what we need to use, so +* just use these hard-coded values for now, as they are correct. +*/ +switch (idx) { +case 0 : iobase =0xe000 ; config_base =0x40 ;break ; +case 1 : iobase =0xe008 ; config_base =0x48 ;break ; +case 2 : iobase =0xe010 ; config_base =0x50 ;break ; +case 3 : iobase =0xe018 ; config_base =0x58 ;break ; +case 4 : iobase =0xe020 ; config_base =0x60 ;break ; +case 5 : iobase =0xe028 ; config_base =0x68 ;break ; +case 6 : iobase =0xe030 ; config_base =0x70 ;break ; +case 7 : iobase =0xe038 ; config_base =0x78 ;break ; +case 8 : iobase =0xe040 ; config_base =0x80 ;break ; +case 9 : iobase =0xe048 ; config_base =0x88 ;break ; +case 10 : iobase =0xe050 ; config_base =0x90 ;break ; +case 11 : iobase =0xe058 ; config_base =0x98 ;break ; +default : +/* Unknown number of ports, get out of here */ +return -EINVAL ; + } + +if (idx <4 ) { + base =pci_resource_start (priv->dev,3 ); + ciobase = (int )(base + (0x8 * idx)); + } + +dev_dbg (&pdev->dev,"%s: idx=%d iobase=0x%lx ciobase=0x%lx config_base=0x%2x\n" , + __func__, idx, iobase, ciobase, config_base); + +/* Enable UART I/O port */ +pci_write_config_byte (pdev, config_base +0x00 ,0x01 ); + +/* Select 128-byte FIFO and 8x FIFO threshold */ +pci_write_config_byte (pdev, config_base +0x01 ,0x33 ); + +/* LSB UART */ +pci_write_config_byte (pdev, config_base +0x04 , (u8)(iobase &0xff )); + +/* MSB UART */ +pci_write_config_byte (pdev, config_base +0x05 , (u8)((iobase &0xff00 ) +>>8 )); + +/* irq number, this usually fails, but the spec says to do it anyway. */ +pci_write_config_byte (pdev, config_base +0x06 , pdev->irq); + + port->port.iotype =UPIO_PORT ; + port->port.iobase = iobase; + port->port.mapbase =0 ; + port->port.membase =NULL ; + port->port.regshift =0 ; + +return 0 ; +} +static int skip_tx_en_setup (struct serial_private *priv,const struct pciserial_board *board, struct uart_8250_port *port, int idx) @@ -2252,6 +2317,27 @@ static struct pci_serial_quirk pci_seria
.subdevice = PCI_ANY_ID,
.setup = pci_brcm_trumanage_setup,
},
+ {
+ .vendor = 0x1c29,
+ .device = 0x1104,
+ .subvendor = PCI_ANY_ID,
+ .subdevice = PCI_ANY_ID,
+ .setup = pci_fintek_setup,
+ },
+ {
+ .vendor = 0x1c29,
+ .device = 0x1108,
+ .subvendor = PCI_ANY_ID,
+ .subdevice = PCI_ANY_ID,
+ .setup = pci_fintek_setup,
+ },
+ {
+ .vendor = 0x1c29,
+ .device = 0x1112,
+ .subvendor = PCI_ANY_ID,
+ .subdevice = PCI_ANY_ID,
+ .setup = pci_fintek_setup,
+ },
/*
* Default "match everything" terminator entry @@ -2449,6 +2535,9 @@ enum pci_board_num_t {
pbn_omegapci,
pbn_NETMOS9900_2s_115200,
pbn_brcm_trumanage,
+ pbn_fintek_4,
+ pbn_fintek_8,
+ pbn_fintek_12,
};
/*
@@ -3199,6 +3288,24 @@ static struct pciserial_board pci_boards
.reg_shift = 2,
.base_baud = 115200,
},
+ [pbn_fintek_4] = {
+ .num_ports = 4,
+ .uart_offset = 8,
+ .base_baud = 115200,
+ .first_offset = 0x40,
+ },
+ [pbn_fintek_8] = {
+ .num_ports = 8,
+ .uart_offset = 8,
+ .base_baud = 115200,
+ .first_offset = 0x40,
+ },
+ [pbn_fintek_12] = {
+ .num_ports = 12,
+ .uart_offset = 8,
+ .base_baud = 115200,
+ .first_offset = 0x40,
+ },
};
static const struct pci_device_id blacklist[] = { @@ -4916,6 +5023,11 @@ static struct pci_device_id serial_pci_t
0,
0, pbn_exar_XR17V358 },
+ /* Fintek PCI serial cards */
+ { PCI_DEVICE(0x1c29, 0x1104), .driver_data = pbn_fintek_4 },
+ { PCI_DEVICE(0x1c29, 0x1108), .driver_data = pbn_fintek_8 },
+ { PCI_DEVICE(0x1c29, 0x1112), .driver_data = pbn_fintek_12 },
+
/*
* These entries match devices with class COMMUNICATION_SERIAL,
* COMMUNICATION_MODEM or COMMUNICATION_MULTISERIAL