Wandboard support for Future Eletronics 7" WVGA LCD extension board
cover Wandboard support for Future Eletronics 7" WVGA LCD extension board
This patchset adds support for the Future Eletronics 7" WVGA LCD extension board and implements its auto-detection using i2c to check for it's touch controller presence.
The IOMUXC change is included here as it makes both SoC type MUX settings in line to each other and took a while to figure out why it worked with one and failed with another SoC.
Otavio Salvador (4):
mx6: Remove PAD_CTL_DSE_120ohm from i.MX6DL's IPU1_DI0_PIN4 pin
wandboard: add Future Eletronics 7" WVGA LCD extension board
wandboard: Use '0' as bootdelay but interruptable
wandboard: Pass 'quiet' bootparam by default
arch/arm/include/asm/arch-mx6/mx6dl_pins.h | 2 +- board/wandboard/wandboard.c | 238 ++++++++++++++++++++++++++--- include/configs/wandboard.h | 38 ++++- 3 files changed, 254 insertions(+), 24 deletions(-)
Signature · 1 line
1.8.4.rc3
PATCH 1/4 mx6: Remove PAD_CTL_DSE_120ohm from i.MX6DL's IPU1_DI0_PIN4 pin
This removes the PAD_CTL_DSE_120ohm as done for i.MX6Q's IPU1_DI0_PIN4 pin definition and makes it aligned with 3.0.35-4.1.0 and 3.12 mainline kernel.
--- arch/arm/include/asm/arch-mx6/mx6dl_pins.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
arch/arm/include/asm/arch-mx6/mx6dl_pins.h +1 -1
@@ -210,7 +210,7 @@ enum {MX6_PAD_DI0_PIN3__MMDC_MMDC_DEBUG_3 =IOMUX_PAD (0x03BC ,0x00A8 ,6 ,0x0000 ,0 ,0 ),MX6_PAD_DI0_PIN3__PL301_SIM_MX6DL_PER1_HADDR_10 =IOMUX_PAD (0x03BC ,0x00A8 ,7 ,0x0000 ,0 ,0 ),MX6_PAD_DI0_PIN3__LCDIF_CS =IOMUX_PAD (0x03BC ,0x00A8 ,8 ,0x0000 ,0 ,0 ), -MX6_PAD_DI0_PIN4__IPU1_DI0_PIN4 =IOMUX_PAD (0x03C0 ,0x00AC ,0 ,0x0000 ,0 , PAD_CTL_DSE_120ohm), +MX6_PAD_DI0_PIN4__IPU1_DI0_PIN4 =IOMUX_PAD (0x03C0 ,0x00AC ,0 ,0x0000 ,0 ,0 ),MX6_PAD_DI0_PIN4__LCDIF_BUSY =IOMUX_PAD (0x03C0 ,0x00AC ,1 ,0x08D8 ,1 ,0 ),MX6_PAD_DI0_PIN4__AUDMUX_AUD6_RXD =IOMUX_PAD (0x03C0 ,0x00AC ,2 ,0x0000 ,0 ,0 ), MX6_PAD_DI0_PIN4__USDHC1_WP = IOMUX_PAD(0x03C0, 0x00AC, 3, 0x092C, 0, 0),
Signature · 1 line
1.8.4.rc3
PATCH 1/4 mx6: Remove PAD_CTL_DSE_120ohm from i.MX6DL's IPU1_DI0_PIN4 pin
Quoted 6 lines · Otavio Salvador
This removes the
PAD_CTL_DSE_120ohmas done for i.MX6Q'sIPU1_DI0_PIN4pin definition and makes it aligned with 3.0.35-4.1.0 and 3.12 mainline kernel.Signed-off-by Otavio Salvador <[email protected]>---
Applied to u-boot-imx, thanks !
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de =====================================================================
PATCH 2/4 wandboard: add Future Eletronics 7" WVGA LCD extension board
In reply to Otavio SalvadorThis adds support for the 7" WVGA produced by Future Eletronics and make it dynamically detect if it is connected or not based on the touchscreen controller.
--- board/wandboard/wandboard.c | 238 ++++++++++++++++++++++++++++++++++++++++---- include/configs/wandboard.h | 35 ++++++- 2 files changed, 251 insertions(+), 22 deletions(-)
board/wandboard/wandboard.c +217 -21
@@ -15,6 +15,7 @@#include <asm/arch/sys_proto.h> #include <asm/gpio.h> #include <asm/imx-common/iomux-v3.h> +#include <asm/imx-common/mxc_i2c.h> #include <asm/imx-common/boot_mode.h> #include <asm/io.h> #include <asm/sizes.h>
@@ -25,6 +26,7 @@#include <miiphy.h> #include <netdev.h> #include <linux/fb.h> +#include <i2c.h> DECLARE_GLOBAL_DATA_PTR ;
@@ -39,6 +41,10 @@ DECLARE_GLOBAL_DATA_PTR;#define ENET_PAD_CTRL (PAD_CTL_PUS_100K_UP | \ PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS) +#define I2C_PAD_CTRL (PAD_CTL_PUS_100K_UP | \ + PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS | \ + PAD_CTL_ODE | PAD_CTL_SRE_FAST) +#define USDHC1_CD_GPIO IMX_GPIO_NR(1, 2)#define USDHC3_CD_GPIO IMX_GPIO_NR(3, 9)#define ETH_PHY_RESET IMX_GPIO_NR(3, 29)
@@ -208,48 +214,236 @@ int board_phy_config(struct phy_device *phydev) }#if defined(CONFIG_VIDEO_IPUV3 ) -static struct fb_videomode const hdmi = { - .name ="HDMI" , - .refresh =60 , - .xres =1024 , - .yres =768 , - .pixclock =15385 , - .left_margin =220 , - .right_margin =40 , - .upper_margin =21 , - .lower_margin =7 , - .hsync_len =60 , - .vsync_len =10 , - .sync =FB_SYNC_EXT , - .vmode =FB_VMODE_NONINTERLACED +struct i2c_pads_info i2c_pad_info = { + .scl = { + .i2c_mode =MX6_PAD_KEY_COL3__I2C2_SCL + |MUX_PAD_CTRL (I2C_PAD_CTRL ), + .gpio_mode =MX6_PAD_KEY_COL3__GPIO_4_12 + |MUX_PAD_CTRL (I2C_PAD_CTRL ), + .gp =IMX_GPIO_NR (4 ,12 ) + }, + .sda = { + .i2c_mode =MX6_PAD_KEY_ROW3__I2C2_SDA + |MUX_PAD_CTRL (I2C_PAD_CTRL ), + .gpio_mode =MX6_PAD_KEY_ROW3__GPIO_4_13 + |MUX_PAD_CTRL (I2C_PAD_CTRL ), + .gp =IMX_GPIO_NR (4 ,13 ) + } }; -int board_video_skip (void ) -{ -int ret; +static iomux_v3_cfg_t const fwadapt_7wvga_pads[] = { +MX6_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK , +MX6_PAD_DI0_PIN2__IPU1_DI0_PIN2 ,/* HSync */ +MX6_PAD_DI0_PIN3__IPU1_DI0_PIN3 ,/* VSync */ +MX6_PAD_DI0_PIN4__IPU1_DI0_PIN4 + |MUX_PAD_CTRL (PAD_CTL_DSE_120ohm),/* Contrast */ +MX6_PAD_DI0_PIN15__IPU1_DI0_PIN15 ,/* DISP0_DRDY */ + +MX6_PAD_DISP0_DAT0__IPU1_DISP0_DAT_0 , +MX6_PAD_DISP0_DAT1__IPU1_DISP0_DAT_1 , +MX6_PAD_DISP0_DAT2__IPU1_DISP0_DAT_2 , +MX6_PAD_DISP0_DAT3__IPU1_DISP0_DAT_3 , +MX6_PAD_DISP0_DAT4__IPU1_DISP0_DAT_4 , +MX6_PAD_DISP0_DAT5__IPU1_DISP0_DAT_5 , +MX6_PAD_DISP0_DAT6__IPU1_DISP0_DAT_6 , +MX6_PAD_DISP0_DAT7__IPU1_DISP0_DAT_7 , +MX6_PAD_DISP0_DAT8__IPU1_DISP0_DAT_8 , +MX6_PAD_DISP0_DAT9__IPU1_DISP0_DAT_9 , +MX6_PAD_DISP0_DAT10__IPU1_DISP0_DAT_10 , +MX6_PAD_DISP0_DAT11__IPU1_DISP0_DAT_11 , +MX6_PAD_DISP0_DAT12__IPU1_DISP0_DAT_12 , +MX6_PAD_DISP0_DAT13__IPU1_DISP0_DAT_13 , +MX6_PAD_DISP0_DAT14__IPU1_DISP0_DAT_14 , +MX6_PAD_DISP0_DAT15__IPU1_DISP0_DAT_15 , +MX6_PAD_DISP0_DAT16__IPU1_DISP0_DAT_16 , +MX6_PAD_DISP0_DAT17__IPU1_DISP0_DAT_17 , + +MX6_PAD_SD4_DAT2__GPIO_2_10 + |MUX_PAD_CTRL (NO_PAD_CTRL ),/* DISP0_BKLEN */ +MX6_PAD_SD4_DAT3__GPIO_2_11 + |MUX_PAD_CTRL (NO_PAD_CTRL ),/* DISP0_VDDEN */ +}; - ret =ipuv3_fb_init (&hdmi,0 ,IPU_PIX_FMT_RGB24 ); +struct display_info_t { +int bus; +int addr; +int pixfmt; +int (*detect)(struct display_info_t const *dev); +void (*enable)(struct display_info_t const *dev); +struct fb_videomode mode; +}; -if (ret) -printf ("HDMI cannot be configured: %d\n" , ret); +static int detect_hdmi (struct display_info_t const *dev) +{ +struct hdmi_regs *hdmi = (struct hdmi_regs *)HDMI_ARB_BASE_ADDR ; +return readb (&hdmi->phy_stat0) &HDMI_DVI_STAT ; +} +static void do_enable_hdmi (struct display_info_t const *dev) +{imx_enable_hdmi_phy (); +} -return ret; +static int detect_i2c (struct display_info_t const *dev) +{ +return ((0 ==i2c_set_bus_num (dev->bus)) && + (0 ==i2c_probe (dev->addr))); +} + +static void enable_fwadapt_7wvga (struct display_info_t const *dev) +{ +imx_iomux_v3_setup_multiple_pads ( + fwadapt_7wvga_pads, +ARRAY_SIZE (fwadapt_7wvga_pads)); + +gpio_direction_output (IMX_GPIO_NR (2 ,10 ),1 ); +gpio_direction_output (IMX_GPIO_NR (2 ,11 ),1 ); +} + +static struct display_info_t const displays[] = {{ + .bus =-1 , + .addr =0 , + .pixfmt =IPU_PIX_FMT_RGB24 , + .detect = detect_hdmi, + .enable = do_enable_hdmi, + .mode = { + .name ="HDMI" , + .refresh =60 , + .xres =1024 , + .yres =768 , + .pixclock =15385 , + .left_margin =220 , + .right_margin =40 , + .upper_margin =21 , + .lower_margin =7 , + .hsync_len =60 , + .vsync_len =10 , + .sync =FB_SYNC_EXT , + .vmode =FB_VMODE_NONINTERLACED +} }, { + .bus =0 , + .addr =0x10 , + .pixfmt =IPU_PIX_FMT_RGB666 , + .detect = detect_i2c, + .enable = enable_fwadapt_7wvga, + .mode = { + .name ="FWBADAPT-LCD-F07A-0102" , + .refresh =60 , + .xres =800 , + .yres =480 , + .pixclock =33260 , + .left_margin =128 , + .right_margin =128 , + .upper_margin =22 , + .lower_margin =22 , + .hsync_len =1 , + .vsync_len =1 , + .sync =0 , + .vmode =FB_VMODE_NONINTERLACED +} } }; + +int board_video_skip (void ) +{ +int i; +int ret; +int detected =0 ; +char const *panel =getenv ("panel" ); +if (!panel) { +for (i =0 ; i <ARRAY_SIZE (displays); i++) { +struct display_info_t const *dev = displays+i; +if (dev->detect && dev->detect (dev)) { + panel = dev->mode.name; + detected =1 ; +break ; + } + } +if (!panel) { + panel = displays[0 ].mode.name; +printf ("No panel detected: default to %s\n" , panel); + i =0 ; + } + }else { +for (i =0 ; i <ARRAY_SIZE (displays); i++) { +if (!strcmp (panel, displays[i].mode.name)) +break ; + } + } +if (i <ARRAY_SIZE (displays)) { + ret =ipuv3_fb_init (&displays[i].mode,0 , + displays[i].pixfmt); + +if (!ret) { + displays[i].enable (displays+i); +printf ("Display: %s (%ux%u) %s\n" , + displays[i].mode.name, + displays[i].mode.xres, + displays[i].mode.yres, + (detected ?"[auto]" :"" )); + }else +printf ("LCD %s cannot be configured: %d\n" , + displays[i].mode.name, ret); + }else { +printf ("unsupported panel %s\n" , panel); +return -EINVAL ; + } + +return 0 ; }static void setup_display (void ) {struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR ; +struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR ;int reg;enable_ipu_clock ();imx_setup_hdmi (); +/* Turn on LDB0, LDB1, IPU,IPU DI0 clocks */ + reg =__raw_readl (&mxc_ccm->CCGR3); + reg |=MXC_CCM_CCGR3_LDB_DI0_MASK |MXC_CCM_CCGR3_LDB_DI1_MASK ; +writel (reg, &mxc_ccm->CCGR3); + +/* set LDB0, LDB1 clk select to 011/011 */ + reg =readl (&mxc_ccm->cs2cdr); + reg &= ~(MXC_CCM_CS2CDR_LDB_DI0_CLK_SEL_MASK + |MXC_CCM_CS2CDR_LDB_DI1_CLK_SEL_MASK ); + reg |= (3 <<MXC_CCM_CS2CDR_LDB_DI0_CLK_SEL_OFFSET ) + | (3 <<MXC_CCM_CS2CDR_LDB_DI1_CLK_SEL_OFFSET ); +writel (reg, &mxc_ccm->cs2cdr); + + reg =readl (&mxc_ccm->cscmr2); + reg |=MXC_CCM_CSCMR2_LDB_DI0_IPU_DIV |MXC_CCM_CSCMR2_LDB_DI1_IPU_DIV ; +writel (reg, &mxc_ccm->cscmr2); + reg =readl (&mxc_ccm->chsccdr); reg |= (CHSCCDR_CLK_SEL_LDB_DI0 <<MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_OFFSET ); + reg |= (CHSCCDR_CLK_SEL_LDB_DI0 + <<MXC_CCM_CHSCCDR_IPU1_DI1_CLK_SEL_OFFSET );writel (reg, &mxc_ccm->chsccdr); + + reg =IOMUXC_GPR2_BGREF_RRMODE_EXTERNAL_RES + |IOMUXC_GPR2_DI1_VS_POLARITY_ACTIVE_LOW + |IOMUXC_GPR2_DI0_VS_POLARITY_ACTIVE_LOW + |IOMUXC_GPR2_BIT_MAPPING_CH1_SPWG + |IOMUXC_GPR2_DATA_WIDTH_CH1_18BIT + |IOMUXC_GPR2_BIT_MAPPING_CH0_SPWG + |IOMUXC_GPR2_DATA_WIDTH_CH0_18BIT + |IOMUXC_GPR2_LVDS_CH0_MODE_DISABLED + |IOMUXC_GPR2_LVDS_CH1_MODE_ENABLED_DI0 ; +writel (reg, &iomux->gpr[2 ]); + + reg =readl (&iomux->gpr[3 ]); + reg = (reg & ~(IOMUXC_GPR3_LVDS1_MUX_CTL_MASK + |IOMUXC_GPR3_HDMI_MUX_CTL_MASK )) + | (IOMUXC_GPR3_MUX_SRC_IPU1_DI0 + <<IOMUXC_GPR3_LVDS1_MUX_CTL_OFFSET ); +writel (reg, &iomux->gpr[3 ]); + +/* Disable LCD backlight */ +imx_iomux_v3_setup_pad (MX6_PAD_DI0_PIN4__GPIO_4_20 ); +gpio_direction_input (IMX_GPIO_NR (4 ,20 )); }#endif /* CONFIG_VIDEO_IPUV3 */
@@ -307,6 +501,8 @@ int board_init(void)/* address of boot parameters */ gd->bd->bi_boot_params =PHYS_SDRAM +0x100 ; +setup_i2c (1 ,CONFIG_SYS_I2C_SPEED ,0x7f , &i2c_pad_info); +return 0 ; }
include/configs/wandboard.h +34 -1
@@ -55,6 +55,12 @@#define CONFIG_LOADADDR 0x12000000#define CONFIG_SYS_TEXT_BASE 0x17800000 +/* I2C Configs */ +#define CONFIG_CMD_I2C +#define CONFIG_I2C_MULTI_BUS +#define CONFIG_I2C_MXC +#define CONFIG_SYS_I2C_SPEED 100000 +/* MMC Configuration */ #define CONFIG_FSL_ESDHC #define CONFIG_FSL_USDHC
@@ -97,6 +103,7 @@#define CONFIG_VIDEO_LOGO #define CONFIG_VIDEO_BMP_LOGO #define CONFIG_IPUV3_CLK 260000000 +#define CONFIG_CMD_HDMIDETECT #define CONFIG_IMX_HDMI #if defined(CONFIG_MX6DL ) || defined(CONFIG_MX6S )
@@ -134,7 +141,33 @@"fi; " \"fi\0" \"mmcargs=setenv bootargs console=${console},${baudrate} " \ -"root=${mmcroot}\0" \ +"root=${mmcroot}; run videoargs\0" \ +"videoargs=" \ +"setenv nextcon 0; " \ +"if hdmidet; then " \ +"setenv bootargs ${bootargs} " \ +"video=mxcfb${nextcon}:dev=hdmi,1280x720M at 60," \ +"if=RGB24; " \ +"setenv fbmen fbmem=28M; " \ +"setexpr nextcon ${nextcon} + 1; " \ +"else " \ +"echo - no HDMI monitor;" \ +"fi; " \ +"i2c dev 0; " \ +"if i2c probe 0x10; then " \ +"setenv bootargs ${bootargs} " \ +"video=mxcfb${nextcon}:dev=lcd,800x480 at 60," \ +"if=RGB666; " \ +"if test 0 -eq ${nextcon}; then " \ +"setenv fbmem fbmem=10M; " \ +"else " \ +"setenv fbmem ${fbmem},10M; " \ +"fi; " \ +"setexpr nextcon ${nextcon} + 1; " \ +"else " \ +"echo '- no FWBADAPT-7WVGA-LCD-F07A-0102 display';" \ +"fi; " \ +"setenv bootargs ${bootargs} ${fbmem}\0" \"loadbootscript=" \"fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \"bootscript=echo Running bootscript from mmc ...; " \
Signature · 1 line
1.8.4.rc3
PATCH 2/4 wandboard: add Future Eletronics 7" WVGA LCD extension board
Quoted 5 lines · On Mon, 21 Oct 2013 21:34:58 -0200 Otavio Salvador <[email protected]>…
This adds support for the 7" WVGA produced by Future Eletronics and make it dynamically detect if it is connected or not based on the touchscreen controller.
Signed-off-by Otavio Salvador <[email protected]>
Nice!
PATCH 3/4 wandboard: Use '0' as bootdelay but interruptable
In reply to Otavio SalvadorThe '0' as bootdelay reduces a lot the boot time while we still allow the boot to be interruptable if need.
--- include/configs/wandboard.h | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-)
include/configs/wandboard.h +2 -1
@@ -48,7 +48,8 @@#define CONFIG_CMD_BMODE #define CONFIG_CMD_SETEXPR -#define CONFIG_BOOTDELAY 5 +#define CONFIG_BOOTDELAY 0 +#define CONFIG_ZERO_BOOTDELAY_CHECK #define CONFIG_SYS_MEMTEST_START 0x10000000#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + 500 * SZ_1M)
Signature · 1 line
1.8.4.rc3
PATCH 4/4 wandboard: Pass 'quiet' bootparam by default
In reply to Otavio SalvadorThis reduces the boot time and makes easier to spot important images.
--- include/configs/wandboard.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
include/configs/wandboard.h +1 -1
@@ -142,7 +142,7 @@"fi; " \"fi\0" \"mmcargs=setenv bootargs console=${console},${baudrate} " \ -"root=${mmcroot}; run videoargs\0" \ +"root=${mmcroot} quiet; run videoargs\0" \"videoargs=" \"setenv nextcon 0; " \"if hdmidet; then " \
Signature · 1 line
1.8.4.rc3
cover Wandboard support for Future Eletronics 7" WVGA LCD extension board
In reply to Otavio SalvadorHi Otavio,
Quoted 15 lines · Otavio Salvador
This patchset adds support for the Future Eletronics 7" WVGA LCD extension board and implements its auto-detection using i2c to check for it's touch controller presence.
The IOMUXC change is included here as it makes both SoC type MUX settings in line to each other and took a while to figure out why it worked with one and failed with another SoC.
Otavio Salvador (4):
mx6: RemovePAD_CTL_DSE_120ohmfrom i.MX6DL'sIPU1_DI0_PIN4pin
wandboard: add Future Eletronics 7" WVGA LCD extension board
wandboard: Use '0' as bootdelay but interruptable
wandboard: Pass 'quiet' bootparam by default
Quoted 4 lines
arch/arm/include/asm/arch-mx6/mx6dl_pins.h | 2 +- board/wandboard/wandboard.c | 238 ++++++++++++++++++++++++++--- include/configs/wandboard.h | 38 ++++- 3 files changed, 254 insertions(+), 24 deletions(-)
I confess that I hoped that Simon's patches to extract the env from the board configuration file could be merged very soon into mainline, but they are not yet merged, and I am blocking some patches, mostly Otavio's. Again, there is also patches adding new feature as this one for the Future Electronics display, that contains also many additions to CONFIG_EXTRA_ENV_SETTINGS.
I will apply the patch for Future's display - it is much more as only a change to default environment - but I am still confident that we can do in the right way once and I will let the other patches in my queue.
Otavio, this regards your patches:
http://patchwork.ozlabs.org/patch/285295/ http://patchwork.ozlabs.org/patch/285296/ http://patchwork.ozlabs.org/patch/285294/
Best regards,
Stefano
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de =====================================================================
cover Wandboard support for Future Eletronics 7" WVGA LCD extension board
Quoted 30 lines · Stefano Babic
Hi Otavio,
Quoted 15 lines · Otavio Salvador
This patchset adds support for the Future Eletronics 7" WVGA LCD extension board and implements its auto-detection using i2c to check for it's touch controller presence.
The IOMUXC change is included here as it makes both SoC type MUX settings in line to each other and took a while to figure out why it worked with one and failed with another SoC.
Otavio Salvador (4):
mx6: RemovePAD_CTL_DSE_120ohmfrom i.MX6DL'sIPU1_DI0_PIN4pin
wandboard: add Future Eletronics 7" WVGA LCD extension board
wandboard: Use '0' as bootdelay but interruptable
wandboard: Pass 'quiet' bootparam by defaultQuoted 4 lines
arch/arm/include/asm/arch-mx6/mx6dl_pins.h | 2 +- board/wandboard/wandboard.c | 238 ++++++++++++++++++++++++++--- include/configs/wandboard.h | 38 ++++- 3 files changed, 254 insertions(+), 24 deletions(-)I confess that I hoped that Simon's patches to extract the env from the board configuration file could be merged very soon into mainline, but they are not yet merged, and I am blocking some patches, mostly Otavio's. Again, there is also patches adding new feature as this one for the Future Electronics display, that contains also many additions to
CONFIG_EXTRA_ENV_SETTINGS.
Quoted 8 lines
I will apply the patch for Future's display - it is much more as only a change to default environment - but I am still confident that we can do in the right way once and I will let the other patches in my queue.
Otavio, this regards your patches:
http://patchwork.ozlabs.org/patch/285295/ http://patchwork.ozlabs.org/patch/285296/ http://patchwork.ozlabs.org/patch/285294/
I think all those should go; As I already said I will rework the environments when Simon's changes are included but holding the development due it is wrong in my point of view.
In fact I stopped sending patches as they are not applied for a while... and this is unfortunate.
Anyway, not my call...
Signature · 3 lines
Otavio Salvador O.S. Systems http://www.ossystems.com.br http://code.ossystems.com.br Mobile: +55 (53) 9981-7854 Mobile: +1 (347) 903-9750