Skip to contentSkip to conversation

mtd: gpmi: Revert "mtd: gpmi: scan two nand chips"

PATCH In review Fabio Estevam 4 participants 8 messages Nov 6, 2013 – Nov 7, 2013

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

PATCH 1/2 mtd: gpmi: Revert "mtd: gpmi: scan two nand chips"

From: Fabio Estevam <[email protected]>

This revert is needed so that the revert of commit f720e7ce5 ("mtd: gpmi: remove the nand_scan()") can be succesfully applied.

This reverts commit cdef39de399fc6806f85c60ef97c9e394b3a92d4.

---
 drivers/mtd/nand/gpmi-nand/gpmi-nand.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/mtd/nand/gpmi-nand/gpmi-nand.c +1 -1
index 7ac2280..a5c60c4 100644
@@ -1674,7 +1674,7 @@ static int gpmi_nfc_init(struct gpmi_nand_data *this)
 	if (ret)
 		goto err_out;
 
-	ret = nand_scan_ident(mtd, 2, NULL);
+	ret = nand_scan_ident(mtd, 1, NULL);
 	if (ret)
 		goto err_out;
 
Signature · 1 line
1.8.1.2
#1 lore raw

PATCH 2/2 mtd: gpmi: Revert "mtd: gpmi: remove the nand_scan()"

From: Fabio Estevam <[email protected]>

Commit f720e7ce (mtd: gpmi: remove the nand_scan()) caused the following regression on mx23:

[    1.150000] NAND device: Manufacturer ID: 0xec, Chip ID: 0xd7 (Samsung NAND 4GiB 3,3V 8-bit), 4096MiB, page size: 4096, OOB size: 8
[    1.160000] Unable to handle kernel NULL pointer dereference at virtual address 000005d0
[    1.170000] pgd = c0004000
[    1.170000] [000005d0] *pgd=00000000
[    1.180000] Internal error: Oops: 5 [#1] ARM
[    1.180000] Modules linked in:
[    1.180000] CPU: 0 PID: 1 Comm: swapper Not tainted 3.12.0 #89
[    1.180000] task: c7440000 ti: c743a000 task.ti: c743a000
[    1.180000] PC is at memcmp+0x10/0x54
[    1.180000] LR is at gpmi_nand_probe+0x42c/0x894
[    1.180000] pc : [<c025fcb0>]    lr : [<c02f6a68>]    psr: 20000053
[    1.180000] sp : c743be2c  ip : 600000d3  fp : ffffffff
[    1.180000] r10: 000005d0  r9 : c02f5f08  r8 : 00000000
[    1.180000] r7 : c75858a8  r6 : c75858a8  r5 : c7585b18  r4 : c7585800
[    1.180000] r3 : 000005d0  r2 : 00000004  r1 : c05c33e4  r0 : 000005d0
[    1.180000] Flags: nzCv  IRQs on  FIQs off  Mode SVC_32  ISA ARM  Segment kernel
[    1.180000] Control: 0005317f  Table: 40004000  DAC: 00000017
[    1.180000] Process swapper (pid: 1, stack limit = 0xc743a1c0)
[    1.180000] Stack: (0xc743be2c to 0xc743c000)
[    1.180000] be20:                            c7585800 c05c316c c7585800 00000000 c012bad0
[    1.180000] be40: c7471810 c0276dd0 c761494c c76149a0 00000000 00000000 00000000 c7471810
[    1.180000] be60: 00000000 c0c09bf8 c06bf6e0 c06a9144 00000079 c06625bc 00000000 c02bfd68
[    1.180000] be80: c02bfd54 c02bebd4 c7471810 c06a9144 c7471844 c06bf6e0 00000000 c02bed84
[    1.180000] bea0: 00000000 c06a9144 c02becf0 c02bd1bc c74038a8 c7467bd0 c06a9144 c759ef80
[    1.180000] bec0: c06a23b8 c02be2a8 c05c3160 c06a9144 c06a9144 00000006 c066ec34 c06bf6e0
[    1.180000] bee0: c743a000 c02bf3ac 00000000 c06777bc 00000006 c00088ac c7440000 c0686908
[    1.180000] bf00: 60000053 c025f4b8 00000000 00000000 00000000 00000000 00000000 c045f4a8
[    1.180000] bf20: 00000002 c743a000 c0d2190e c049e9e4 00000079 c0037c20 c0617e98 00000006
[    1.180000] bf40: c0d21916 00000006 60000053 c06777bc 00000006 c066ec34 c06bf6e0 c0640480
[    1.180000] bf60: 00000079 c066ec40 00000000 c0640ac4 00000006 00000006 c0640480 6559f550
[    1.180000] bf80: 00000000 c04559ec 00000000 c04559ec 00000000 00000000 00000000 00000000
[    1.180000] bfa0: 00000000 c04559f4 00000000 c000ee60 00000000 00000000 00000000 00000000
[    1.180000] bfc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[    1.180000] bfe0: 00000000 00000000 00000000 00000000 00000013 00000000 54555574 57555555
[    1.180000] [<c025fcb0>] (memcmp+0x10/0x54) from [<c05c316c>] (__func__.15198+0x103c94/0x1254e8)
[    1.180000] Code: e3520000 e52d4004 e1a03000 0a00000e (e5d0c000) 
[    1.390000] ---[ end trace 0aae7882440a8ce8 ]---
[    1.400000] Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b

This reverts commit f720e7ce510bf79f029be45ce200ccfce5551280.

---
Kernel 3.11 boots fine on mx23, but 3.12 fails because of this commit.

 drivers/mtd/nand/gpmi-nand/gpmi-nand.c | 65 ++++++++++++++++------------------
 1 file changed, 30 insertions(+), 35 deletions(-)
drivers/mtd/nand/gpmi-nand/gpmi-nand.c +30 -35
index a5c60c4..5eaefdb 100644
@@ -217,6 +217,7 @@ static bool set_geometry_by_ecc_info(struct gpmi_nand_data *this)
 	if (geo->page_size < mtd->writesize + mtd->oobsize) {
 		of->offset = geo->page_size - mtd->writesize;
 		of->length = mtd->oobsize - of->offset;
+		mtd->oobavail = gpmi_hw_ecclayout.oobavail = of->length;
 	}
 
 	geo->payload_size = mtd->writesize;
@@ -1591,22 +1592,19 @@ static int gpmi_pre_bbt_scan(struct gpmi_nand_data  *this)
 	if (ret)
 		return ret;
 
+	/* Adjust the ECC strength according to the chip. */
+	this->nand.ecc.strength = this->bch_geometry.ecc_strength;
+	this->mtd.ecc_strength = this->bch_geometry.ecc_strength;
+	this->mtd.bitflip_threshold = this->bch_geometry.ecc_strength;
+
 	/* NAND boot init, depends on the gpmi_set_geometry(). */
 	return nand_boot_init(this);
 }
 
-static void gpmi_nfc_exit(struct gpmi_nand_data *this)
-{
-	nand_release(&this->mtd);
-	gpmi_free_dma_buffer(this);
-}
-
-static int gpmi_init_last(struct gpmi_nand_data *this)
+static int gpmi_scan_bbt(struct mtd_info *mtd)
 {
-	struct mtd_info *mtd = &this->mtd;
 	struct nand_chip *chip = mtd->priv;
-	struct nand_ecc_ctrl *ecc = &chip->ecc;
-	struct bch_geometry *bch_geo = &this->bch_geometry;
+	struct gpmi_nand_data *this = chip->priv;
 	int ret;
 
 	/* Prepare for the BBT scan. */
@@ -1614,16 +1612,6 @@ static int gpmi_init_last(struct gpmi_nand_data *this)
 	if (ret)
 		return ret;
 
-	/* Init the nand_ecc_ctrl{} */
-	ecc->read_page	= gpmi_ecc_read_page;
-	ecc->write_page	= gpmi_ecc_write_page;
-	ecc->read_oob	= gpmi_ecc_read_oob;
-	ecc->write_oob	= gpmi_ecc_write_oob;
-	ecc->mode	= NAND_ECC_HW;
-	ecc->size	= bch_geo->ecc_chunk_size;
-	ecc->strength	= bch_geo->ecc_strength;
-	ecc->layout	= &gpmi_hw_ecclayout;
-
 	/*
 	 * Can we enable the extra features? such as EDO or Sync mode.
 	 *
@@ -1632,7 +1620,14 @@ static int gpmi_init_last(struct gpmi_nand_data *this)
 	 */
 	gpmi_extra_init(this);
 
-	return 0;
+	/* use the default BBT implementation */
+	return nand_default_bbt(mtd);
+}
+
+static void gpmi_nfc_exit(struct gpmi_nand_data *this)
+{
+	nand_release(&this->mtd);
+	gpmi_free_dma_buffer(this);
 }
 
 static int gpmi_nfc_init(struct gpmi_nand_data *this)
@@ -1658,33 +1653,33 @@ static int gpmi_nfc_init(struct gpmi_nand_data *this)
 	chip->read_byte		= gpmi_read_byte;
 	chip->read_buf		= gpmi_read_buf;
 	chip->write_buf		= gpmi_write_buf;
+	chip->ecc.read_page	= gpmi_ecc_read_page;
+	chip->ecc.write_page	= gpmi_ecc_write_page;
+	chip->ecc.read_oob	= gpmi_ecc_read_oob;
+	chip->ecc.write_oob	= gpmi_ecc_write_oob;
+	chip->scan_bbt		= gpmi_scan_bbt;
 	chip->badblock_pattern	= &gpmi_bbt_descr;
 	chip->block_markbad	= gpmi_block_markbad;
 	chip->options		|= NAND_NO_SUBPAGE_WRITE;
+	chip->ecc.mode		= NAND_ECC_HW;
+	chip->ecc.size		= 1;
+	chip->ecc.strength	= 8;
+	chip->ecc.layout	= &gpmi_hw_ecclayout;
 	if (of_get_nand_on_flash_bbt(this->dev->of_node))
 		chip->bbt_options |= NAND_BBT_USE_FLASH | NAND_BBT_NO_OOB;
 
-	/*
-	 * Allocate a temporary DMA buffer for reading ID in the
-	 * nand_scan_ident().
-	 */
+	/* Allocate a temporary DMA buffer for reading ID in the nand_scan() */
 	this->bch_geometry.payload_size = 1024;
 	this->bch_geometry.auxiliary_size = 128;
 	ret = gpmi_alloc_dma_buffer(this);
 	if (ret)
 		goto err_out;
 
-	ret = nand_scan_ident(mtd, 1, NULL);
-	if (ret)
-		goto err_out;
-
-	ret = gpmi_init_last(this);
-	if (ret)
-		goto err_out;
-
-	ret = nand_scan_tail(mtd);
-	if (ret)
+	ret = nand_scan(mtd, 1);
+	if (ret) {
+		pr_err("Chip scan failed\n");
 		goto err_out;
+	}
 
 	ppdata.of_node = this->pdev->dev.of_node;
 	ret = mtd_device_parse_register(mtd, NULL, &ppdata, NULL, 0);
Signature · 1 line
1.8.1.2
#2 lore raw

Re: [PATCH 2/2] mtd: gpmi: Revert "mtd: gpmi: remove the nand_scan()"

Quoted 4 lines · Fabio Estevam

From: Fabio Estevam <[email protected]>

Commit f720e7ce (mtd: gpmi: remove the nand_scan()) caused the following regression on mx23:

...

Quoted 6 lines

This reverts commit f720e7ce510bf79f029be45ce200ccfce5551280.

---
Kernel 3.11 boots fine on mx23, but 3.12 fails because of this commit.

I seriously doubt that a total revert is the correct answer to this problem. Can you pick up the discussion with Huang on the mailing list, or at least explain what the actual root cause is? Have you been going through some private communication on this issue? A proper bugfix with an identified issue is preferable to a blind revert.

Huang, is the DMA patch you sent related, or is it a totally different bug?

Brian

#3 lore raw

Re: [PATCH 2/2] mtd: gpmi: Revert "mtd: gpmi: remove the nand_scan()"

Hi Brian,

Quoted 2 lines · Brian Norris

I seriously doubt that a total revert is the correct answer to this problem. Can you pick up the discussion with Huang on the mailing

Agree that it would be better to come up with a better localized fix rather than the complete revert, but I currently don't have the time to spend on debugging this issue.

On the other hand, I would not like to see mx23 broken in 3.12 because of this. It can't even reach the prompt.

Quoted 3 lines

list, or at least explain what the actual root cause is? Have you been going through some private communication on this issue? A proper bugfix with an identified issue is preferable to a blind revert.

No private communication. I reported this issue in the mailing list:
http://lists.infradead.org/pipermail/linux-mtd/2013-November/049641.html

Regards,

Fabio Estevam

#4 lore raw

Re: [PATCH 2/2] mtd: gpmi: Revert "mtd: gpmi: remove the nand_scan()"

Quoted 8 lines · Fabio Estevam
Quoted 2 lines · Brian Norris

I seriously doubt that a total revert is the correct answer to this problem. Can you pick up the discussion with Huang on the mailing

Agree that it would be better to come up with a better localized fix rather than the complete revert, but I currently don't have the time to spend on debugging this issue.

OK. And if Huang doesn't have the time to clean up his mess, then we will have to revert things.

Quoted 2 lines

On the other hand, I would not like to see mx23 broken in 3.12 because of this. It can't even reach the prompt.

3.12 is already out the door, so we now have some time to get a proper fix into -stable.

Quoted 6 lines
Quoted 3 lines

list, or at least explain what the actual root cause is? Have you been going through some private communication on this issue? A proper bugfix with an identified issue is preferable to a blind revert.

No private communication. I reported this issue in the mailing list:
http://lists.infradead.org/pipermail/linux-mtd/2013-November/049641.html

Right. But this ended with you pointing Huang to the right U-boot setup, then everything went silent. And today, I get a blunt revert request from you as well as an independent DMA fix from Huang. Since you guys are both from Freescale, I wasn't sure if there was any coordination/correlation, or if this is really as uncoordinated as it looks.

Brian

#5 lore raw

Re: [PATCH 2/2] mtd: gpmi: Revert "mtd: gpmi: remove the nand_scan()"

Hi Brian,

Quoted 9 lines · Brian Norris
Quoted 2 lines

No private communication. I reported this issue in the mailing list:
http://lists.infradead.org/pipermail/linux-mtd/2013-November/049641.html

Right. But this ended with you pointing Huang to the right U-boot setup, then everything went silent. And today, I get a blunt revert request from you as well as an independent DMA fix from Huang. Since you guys are both from Freescale, I wasn't sure if there was any coordination/correlation, or if this is really as uncoordinated as it looks.

Sorry for the confusion.

The DMA fix Huang sent today is unrelated to this mx23 kernel crash on boot.

Regards,

Fabio Estevam

#6 lore raw

Re: [PATCH 2/2] mtd: gpmi: Revert "mtd: gpmi: remove the nand_scan()"

In reply to Brian Norris

Dear Brian Norris,

Quoted 7 lines · Fabio Estevam
Quoted 6 lines

On Wed, Nov 6, 2013 at 4:08 PM, Brian Norris

Quoted 2 lines · <[email protected]> wrote:

I seriously doubt that a total revert is the correct answer to this problem. Can you pick up the discussion with Huang on the mailing

Quoted 6 lines
Quoted 3 lines

Agree that it would be better to come up with a better localized fix rather than the complete revert, but I currently don't have the time to spend on debugging this issue.

OK. And if Huang doesn't have the time to clean up his mess, then we will have to revert things.

I have an MX23EVK here, don't make me use it! ;-)

Quoted 13 lines
Quoted 2 lines

On the other hand, I would not like to see mx23 broken in 3.12 because of this. It can't even reach the prompt.

3.12 is already out the door, so we now have some time to get a proper fix into -stable.

Quoted 6 lines
Quoted 3 lines

list, or at least explain what the actual root cause is? Have you been going through some private communication on this issue? A proper bugfix with an identified issue is preferable to a blind revert.

No private communication. I reported this issue in the mailing list:
http://lists.infradead.org/pipermail/linux-mtd/2013-November/049641.html

Quoted 6 lines

Right. But this ended with you pointing Huang to the right U-boot setup, then everything went silent. And today, I get a blunt revert request from you as well as an independent DMA fix from Huang. Since you guys are both from Freescale, I wasn't sure if there was any coordination/correlation, or if this is really as uncoordinated as it looks.

Left hand doesn't know what the right one does in such big companies :(

Best regards,
Marek Vasut

#7 lore raw
In reply to Fabio Estevam
Quoted 17 lines · Fabio Estevam

From: Fabio Estevam <[email protected]>

This revert is needed so that the revert of commit f720e7ce5 ("mtd: gpmi: remove the nand_scan()") can be succesfully applied.

This reverts commit cdef39de399fc6806f85c60ef97c9e394b3a92d4.

---
 drivers/mtd/nand/gpmi-nand/gpmi-nand.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/mtd/nand/gpmi-nand/gpmi-nand.c +0 -0
index 7ac2280..a5c60c4 100644

drivers/mtd/nand/gpmi-nand/gpmi-nand.c static int gpmi_nfc_init(struct gpmi_nand_data *this) · line 1680

Quoted 8 lines
drivers/mtd/nand/gpmi-nand/gpmi-nand.c +1 -1
@@ -1674,7 +1674,7 @@ static int gpmi_nfc_init(struct gpmi_nand_data *this)
 	if (ret)
 		goto err_out;
 
-	ret = nand_scan_ident(mtd, 2, NULL);
+	ret = nand_scan_ident(mtd, 1, NULL);
 	if (ret)
 		goto err_out;
 

Please do not revert the patches.

It's not the right way to fix this.
I will spend some time to this bug today.

thanks

Huang Shijie