ARM: l2x0: add prefetch and power ctrl registers configuration support
Subsystems (2)
PATCH 1/1 ARM: l2x0: add prefetch and power ctrl registers configuration support
PL310 supports Prefetch offset/control register from r2p0 and Power control register from r3p0. This patch adds the support to configure these two registers if there are. The dt binding document is also updated.
--- Documentation/devicetree/bindings/arm/l2cc.txt | 4 ++++ arch/arm/mm/cache-l2x0.c | 19 +++++++++++++++++++ 2 files changed, 23 insertions(+)
Documentation/devicetree/bindings/arm/l2cc.txt +4 -0
@@ -39,6 +39,10 @@ Optional properties: - arm,filter-ranges : <start length> Starting address and length of window to filter. Addresses in the filter window are directed to the M1 port. Other addresses will go to the M0 port. +- arm,prefetch-ctrl : The value for Prefetch Offset/Control Register if there + is. This is a single cell. +- arm,pwr-ctrl : The value for Power Control Register if there is. This is a + single cell. - interrupts : 1 combined interrupt. - cache-id-part: cache id part number to be used if it is not present on hardware
arch/arm/mm/cache-l2x0.c +19 -0
@@ -704,6 +704,8 @@ static void __init pl310_of_setup(const struct device_node *np,u32 data[3 ] = {0 ,0 ,0 };u32 tag[3 ] = {0 ,0 ,0 };u32 filter[2 ] = {0 ,0 }; +u32 l2x0_revision =readl_relaxed (l2x0_base +L2X0_CACHE_ID ) & +L2X0_CACHE_ID_RTL_MASK ;of_property_read_u32_array (np,"arm,tag-latency" , tag,ARRAY_SIZE (tag));if (tag[0 ] && tag[1 ] && tag[2 ])
@@ -730,6 +732,23 @@ static void __init pl310_of_setup(const struct device_node *np,writel_relaxed ((filter[0 ] & ~(SZ_1M -1 )) |L2X0_ADDR_FILTER_EN , l2x0_base +L2X0_ADDR_FILTER_START ); } + +if (l2x0_revision >=L2X0_CACHE_ID_RTL_R2P0 ) { +u32 prefetch_ctrl =0 ; + +of_property_read_u32 (np,"arm,prefetch-ctrl" , + &prefetch_ctrl); +if (prefetch_ctrl) +writel_relaxed (prefetch_ctrl, l2x0_base + +L2X0_PREFETCH_CTRL ); +if (l2x0_revision >=L2X0_CACHE_ID_RTL_R3P0 ) { +u32 pwr_ctrl =0 ; +of_property_read_u32 (np,"arm,pwr-ctrl" , &pwr_ctrl); +if (pwr_ctrl) +writel_relaxed (pwr_ctrl, l2x0_base + +L2X0_POWER_CTRL ); + } + } }static void __init pl310_save (void )
Signature · 1 line
1.8.4.2
Quoted 15 lines · Jisheng Zhang
PL310 supports Prefetch offset/control register from r2p0 and Power control register from r3p0. This patch adds the support to configure these two registers if there are. The dt binding document is also updated.
Signed-off-by Jisheng Zhang <[email protected]>--- Documentation/devicetree/bindings/arm/l2cc.txt | 4 ++++ arch/arm/mm/cache-l2x0.c | 19 +++++++++++++++++++ 2 files changed, 23 insertions(+)Documentation/devicetree/bindings/arm/l2cc.txt +0
-0
Documentation/devicetree/bindings/arm/l2cc.txt Optional properties: · line 45
Quoted 7 lines
Documentation/devicetree/bindings/arm/l2cc.txt +4
-0@@ -39,6 +39,10 @@ Optional properties: - arm,filter-ranges : <start length> Starting address and length of window to filter. Addresses in the filter window are directed to the M1 port. Other addresses will go to the M0 port. +- arm,prefetch-ctrl : The value for Prefetch Offset/Control Register if there + is. This is a single cell. +- arm,pwr-ctrl : The value for Power Control Register if there is. This is a + single cell.
Jisheng,
I did some research over L2x0/L310 aux-ctrl registers and possible properties for them. Both properties introduced here, just allow you to put in a magic number, while IMHO properties should better reflect the actual function rather than hard-coded values.
A quick look at L310 TRM for Power Control Register gives:
Bit 1: dynamic_clk_gating_en (1=enabled, 0=masked) Bit 0: standby mode en (1=enabled, 0=masked)
So, properties should one of:
(a) arm,dynamic-clock-gating = <0/1>
arm,standby-mode = <0/1>
(b) arm,dynamic-clock-gating-enable/-disable;
arm,standby-mode-enable/-disable
If we want to have set/clear/don't touch behavior, I'd prefer (a) as it is easier to deal with in code. Moreover, -enable/-disable of (b) may not always fit the property name, so there will also be arm,no-feature-foo or arm,force-feature-bar.
The same also applies for Prefetch Control register, too.
Sebastian
Quoted 41 lines
Documentation/devicetree/bindings/arm/l2cc.txt +0
-0- interrupts : 1 combined interrupt. - cache-id-part: cache id part number to be used if it is not present on hardwarearch/arm/mm/cache-l2x0.c +19
-0@@ -704,6 +704,8 @@ static void __init pl310_of_setup(const struct device_node *np,u32 data[3 ] = {0 ,0 ,0 };u32 tag[3 ] = {0 ,0 ,0 };u32 filter[2 ] = {0 ,0 }; +u32 l2x0_revision =readl_relaxed (l2x0_base +L2X0_CACHE_ID ) & +L2X0_CACHE_ID_RTL_MASK ;of_property_read_u32_array (np,"arm,tag-latency" , tag,ARRAY_SIZE (tag));if (tag[0 ] && tag[1 ] && tag[2 ])@@ -730,6 +732,23 @@ static void __init pl310_of_setup(const struct device_node *np,writel_relaxed ((filter[0 ] & ~(SZ_1M -1 )) |L2X0_ADDR_FILTER_EN , l2x0_base +L2X0_ADDR_FILTER_START ); } + +if (l2x0_revision >=L2X0_CACHE_ID_RTL_R2P0 ) { +u32 prefetch_ctrl =0 ; + +of_property_read_u32 (np,"arm,prefetch-ctrl" , + &prefetch_ctrl); +if (prefetch_ctrl) +writel_relaxed (prefetch_ctrl, l2x0_base + +L2X0_PREFETCH_CTRL ); +if (l2x0_revision >=L2X0_CACHE_ID_RTL_R3P0 ) { +u32 pwr_ctrl =0 ; +of_property_read_u32 (np,"arm,pwr-ctrl" , &pwr_ctrl); +if (pwr_ctrl) +writel_relaxed (pwr_ctrl, l2x0_base + +L2X0_POWER_CTRL ); + } + } }static void __init pl310_save (void )
Quoted 39 lines · Sebastian Hesselbarth
Quoted 15 lines · Jisheng Zhang
PL310 supports Prefetch offset/control register from r2p0 and Power control register from r3p0. This patch adds the support to configure these two registers if there are. The dt binding document is also updated.
Signed-off-by Jisheng Zhang <[email protected]>--- Documentation/devicetree/bindings/arm/l2cc.txt | 4 ++++ arch/arm/mm/cache-l2x0.c | 19 +++++++++++++++++++ 2 files changed, 23 insertions(+)Documentation/devicetree/bindings/arm/l2cc.txt +0
-0Documentation/devicetree/bindings/arm/l2cc.txt Optional properties: · line 45
Quoted 7 lines
Documentation/devicetree/bindings/arm/l2cc.txt +4
-0@@ -39,6 +39,10 @@ Optional properties: - arm,filter-ranges : <start length> Starting address and length of window to filter. Addresses in the filter window are directed to the M1 port. Other addresses will go to the M0 port. +- arm,prefetch-ctrl : The value for Prefetch Offset/Control Register if there + is. This is a single cell. +- arm,pwr-ctrl : The value for Power Control Register if there is. This is a + single cell.Jisheng,
I did some research over L2x0/L310 aux-ctrl registers and possible properties for them. Both properties introduced here, just allow you to put in a magic number, while IMHO properties should better reflect the actual function rather than hard-coded values.
A quick look at L310 TRM for Power Control Register gives:
Bit 1:
dynamic_clk_gating_en(1=enabled, 0=masked) Bit 0: standby mode en (1=enabled, 0=masked)So, properties should one of:
(a) arm,dynamic-clock-gating = <0/1>
Quoted 8 lines
arm,standby-mode = <0/1>(b) arm,dynamic-clock-gating-enable/-disable;
arm,standby-mode-enable/-disableIf we want to have set/clear/don't touch behavior, I'd prefer (a) as it is easier to deal with in code. Moreover, -enable/-disable of (b) may not always fit the property name, so there will also be arm,no-feature-foo or arm,force-feature-bar.
Hi Sebastian
There have been some comments about properties with Boolean values. Rather than having a Boolean, you simply don't list the property.
What you have here is slightly different, since you have set/clear/don't touch. How to represent this should be decided once by the DT folks, and used consistently in all bindings.
Andrew
Quoted 3 lines · Jisheng Zhang
PL310 supports Prefetch offset/control register from r2p0 and Power control register from r3p0. This patch adds the support to configure these two registers if there are. The dt binding document is also updated.
I'd like to see a reasoning as to _why_ these should be in the DT.
While we have tag and data RAM latency information, those are hardware properties that we cannot probe. I'm not so clear on the filter-ranges property.
These bits seem to be configuration rather than a hardware description. If there are some portions of this that we can describe with higher level properties, I'd prefer to do that.
But primarily, the question to answer is do we need these, and if so do they belong in the DT?
Quoted 38 lines
Signed-off-by Jisheng Zhang <[email protected]>--- Documentation/devicetree/bindings/arm/l2cc.txt | 4 ++++ arch/arm/mm/cache-l2x0.c | 19 +++++++++++++++++++ 2 files changed, 23 insertions(+)Documentation/devicetree/bindings/arm/l2cc.txt +4
-0@@ -39,6 +39,10 @@ Optional properties: - arm,filter-ranges : <start length> Starting address and length of window to filter. Addresses in the filter window are directed to the M1 port. Other addresses will go to the M0 port. +- arm,prefetch-ctrl : The value for Prefetch Offset/Control Register if there + is. This is a single cell. +- arm,pwr-ctrl : The value for Power Control Register if there is. This is a + single cell. - interrupts : 1 combined interrupt. - cache-id-part: cache id part number to be used if it is not present on hardwarearch/arm/mm/cache-l2x0.c +2
-0@@ -704,6 +704,8 @@ static void __init pl310_of_setup(const struct device_node *np,u32 data[3 ] = {0 ,0 ,0 };u32 tag[3 ] = {0 ,0 ,0 };u32 filter[2 ] = {0 ,0 }; +u32 l2x0_revision =readl_relaxed (l2x0_base +L2X0_CACHE_ID ) & +L2X0_CACHE_ID_RTL_MASK ;of_property_read_u32_array (np,"arm,tag-latency" , tag,ARRAY_SIZE (tag));if (tag[0 ] && tag[1 ] && tag[2 ])@@ -730,6 +732,23 @@ static void __init pl310_of_setup(const struct device_node *np,writel_relaxed ((filter[0 ] & ~(SZ_1M -1 )) |L2X0_ADDR_FILTER_EN , l2x0_base +L2X0_ADDR_FILTER_START );
arch/arm/mm/cache-l2x0.c static void __init pl310_of_setup(const struct device_node *np, · line 743
Quoted 10 lines
arch/arm/mm/cache-l2x0.c +9
-0} + +if (l2x0_revision >=L2X0_CACHE_ID_RTL_R2P0 ) { +u32 prefetch_ctrl =0 ; + +of_property_read_u32 (np,"arm,prefetch-ctrl" , + &prefetch_ctrl); +if (prefetch_ctrl) +writel_relaxed (prefetch_ctrl, l2x0_base + +L2X0_PREFETCH_CTRL );
Some of the prefetch control regsiter bits are reserved, and the prefetch offset may only take a subset of possible values. I wouldn't want to poke the hardware without performing some sanity checking on these values.
arch/arm/mm/cache-l2x0.c static void __init pl310_of_setup(const struct device_node *np, · line 749
Quoted 6 lines
arch/arm/mm/cache-l2x0.c +6
-0+if (l2x0_revision >=L2X0_CACHE_ID_RTL_R3P0 ) { +u32 pwr_ctrl =0 ; +of_property_read_u32 (np,"arm,pwr-ctrl" , &pwr_ctrl); +if (pwr_ctrl) +writel_relaxed (pwr_ctrl, l2x0_base + +L2X0_POWER_CTRL );
Similarly, all but the lower 2 bits are reserved...
Thanks,
Mark.
Hi Mark,
Quoted 11 lines · On Wed, 27 Nov 2013 09:42:04 -0800 Mark Rutland <[email protected]> wrote:
Quoted 3 lines · Jisheng Zhang
PL310 supports Prefetch offset/control register from r2p0 and Power control register from r3p0. This patch adds the support to configure these two registers if there are. The dt binding document is also updated.
I'd like to see a reasoning as to _why_ these should be in the DT.
While we have tag and data RAM latency information, those are hardware properties that we cannot probe. I'm not so clear on the filter-ranges property.
Quoted 6 lines
These bits seem to be configuration rather than a hardware description. If there are some portions of this that we can describe with higher level properties, I'd prefer to do that.
But primarily, the question to answer is do we need these, and if so do they belong in the DT?
After more consideration, configuring these two registers in bootloader or TrustZone firmware is more reasonable since the prefetch controller can only be written in Secure World.
PS: the tag/ram latency must also be written in secure world, and IMHO, the latency and filter-ranges are also configurations
Thanks for having look at this patch,
Jisheng
Quoted 69 lines
Quoted 41 lines
Signed-off-by Jisheng Zhang <[email protected]>--- Documentation/devicetree/bindings/arm/l2cc.txt | 4 ++++ arch/arm/mm/cache-l2x0.c | 19 +++++++++++++++++++ 2 files changed, 23 insertions(+)(quoted diff) +0
-0
b/Documentation/devicetree/bindings/arm/l2cc.txtindex c0c7626..32cd08c 100644 ---a/Documentation/devicetree/bindings/arm/l2cc.txt+++b/Documentation/devicetree/bindings/arm/l2cc.txt(quoted diff) +0
-0@@ -39,6 +39,10 @@ Optional properties: - arm,filter-ranges : <start length> Starting address and length ofwindow to filter. Addresses in the filter window are directed to the M1 port. Other addresses will go to the M0 port.
+- arm,prefetch-ctrl : The value for Prefetch Offset/Control Register if there
+ is. This is a single cell.
+- arm,pwr-ctrl : The value for Power Control Register if there is. This is aDocumentation/devicetree/bindings/arm/l2cc.txt +1
-0+ single cell. - interrupts : 1 combined interrupt. - cache-id-part: cache id part number to be used if it is not present on hardwarearch/arm/mm/cache-l2x0.c +2
-0@@ -704,6 +704,8 @@ static void __init pl310_of_setup(const struct device_node *np, u32 data[3] = { 0, 0, 0 };u32 tag[3 ] = {0 ,0 ,0 };u32 filter[2 ] = {0 ,0 }; +u32 l2x0_revision =readl_relaxed (l2x0_base +L2X0_CACHE_ID ) & +L2X0_CACHE_ID_RTL_MASK ;of_property_read_u32_array (np,"arm,tag-latency" , tag,ARRAY_SIZE (tag));if (tag[0 ] && tag[1 ] && tag[2 ])@@ -730,6 +732,23 @@ static void __init pl310_of_setup(const struct
device_node*np,writel_relaxed((filter[0] & ~(SZ_1M - 1)) | L2X0_ADDR_FILTER_EN, l2x0_base + L2X0_ADDR_FILTER_START);arch/arm/mm/cache-l2x0.c static void __init pl310_of_setup(const struct device_node *np, · line 743
Quoted 10 lines
arch/arm/mm/cache-l2x0.c +9
-0} + +if (l2x0_revision >=L2X0_CACHE_ID_RTL_R2P0 ) { +u32 prefetch_ctrl =0 ; + +of_property_read_u32 (np,"arm,prefetch-ctrl" , + &prefetch_ctrl); +if (prefetch_ctrl) +writel_relaxed (prefetch_ctrl, l2x0_base + +L2X0_PREFETCH_CTRL );Some of the prefetch control regsiter bits are reserved, and the prefetch offset may only take a subset of possible values. I wouldn't want to poke the hardware without performing some sanity checking on these values.
arch/arm/mm/cache-l2x0.c static void __init pl310_of_setup(const struct device_node *np, · line 749
Quoted 7 lines
arch/arm/mm/cache-l2x0.c +3
-0+if (l2x0_revision >=L2X0_CACHE_ID_RTL_R3P0 ) { +u32 pwr_ctrl =0 ; + of_property_read_u32(np, "arm,pwr-ctrl",
&pwr_ctrl);arch/arm/mm/cache-l2x0.c +3
-0+if (pwr_ctrl) +writel_relaxed (pwr_ctrl, l2x0_base + +L2X0_POWER_CTRL );Similarly, all but the lower 2 bits are reserved...
Thanks,
Mark.