Skip to contentSkip to conversation

powerpc/t2080qds: add support for t2080qds board

PATCH Superseded Shengzhou Liu 3 participants 3 messages Nov 14, 2013 – Nov 25, 2013 PowerPC

v1 of 2 Superseded Latest is v2 →

lore
Share & tools
lore
#0 lore raw

PATCH 3/4 powerpc/t2080qds: add support for t2080qds board

The T2080QDS is a high-performance computing evaluation, development and test platform supporting the T2080 QorIQ Power Architecture processor.

T2080QDS feature overview
Processor:
- T2080 SoC integrating four 64-bit dual-threads e6500 cores up to 1.8GHz
Memory:
- Single memory controller capable of supporting DDR3 and DDR3-LV devices
- Two DDR3 DIMMs up to 4GB, Dual rank @ 2133MT/s and ECC support
Ethernet interfaces:
- Two 1Gbps RGMII on-board ports
- Four 10Gbps XFI on-board cages
- 1Gbps/2.5Gbps SGMII Riser card
- 10Gbps XAUI Riser card
Accelerator:
- DPAA components consist of FMan, BMan, QMan, PME, DCE and SEC
SerDes:
- 16 lanes up to 10.3125GHz
- Supports Aurora debug, PEX, SATA, SGMII, sRIO, HiGig, XFI and XAUI
IFC:
- 128MB NOR Flash, 512MB NAND Flash, PromJet debug port and FPGA
eSPI:
- Three SPI flash (16MB N25Q128A + 16MB EN25S64 + 512KB SST25WF040)
USB:
- Two USB2.0 ports with internal PHY (one Type-A + one micro Type-AB)
PCIE:
- Four PCI Express controllers (two PCIe 2.0 and two PCIe 3.0 with SR-IOV)
SATA:
- Two SATA 2.0 ports on-board
SRIO:
- Two Serial RapidIO 2.0 ports up to 5 GHz
eSDHC:
- Supports SD/SDHC/SDXC/eMMC Card
I2C:
- Four I2C controllers.
UART:
- Dual 4-pins UART serial ports
System Logic:
- QIXIS-II FPGA system controll
Debug Features:
- Support Legacy, COP/JTAG, Aurora, Event and EVT

---
Against master branch of upstream.

 arch/powerpc/include/asm/config_mpc85xx.h |   1 +
 board/freescale/t2080qds/Makefile         |  13 +
 board/freescale/t2080qds/ddr.c            | 127 +++++
 board/freescale/t2080qds/ddr.h            |  85 ++++
 board/freescale/t2080qds/eth_t2080qds.c   | 514 +++++++++++++++++++
 board/freescale/t2080qds/law.c            |  34 ++
 board/freescale/t2080qds/pci.c            |  23 +
 board/freescale/t2080qds/t2080qds.c       | 327 ++++++++++++
 board/freescale/t2080qds/t2080qds.h       |  13 +
 board/freescale/t2080qds/t2080qds_qixis.h |  47 ++
 board/freescale/t2080qds/tlb.c            | 146 ++++++
 boards.cfg                                |   5 +
 include/configs/T2080QDS.h                | 806 ++++++++++++++++++++++++++++++
 13 files changed, 2141 insertions(+)
 create mode 100644 board/freescale/t2080qds/Makefile
 create mode 100644 board/freescale/t2080qds/ddr.c
 create mode 100644 board/freescale/t2080qds/ddr.h
 create mode 100644 board/freescale/t2080qds/eth_t2080qds.c
 create mode 100644 board/freescale/t2080qds/law.c
 create mode 100644 board/freescale/t2080qds/pci.c
 create mode 100644 board/freescale/t2080qds/t2080qds.c
 create mode 100644 board/freescale/t2080qds/t2080qds.h
 create mode 100644 board/freescale/t2080qds/t2080qds_qixis.h
 create mode 100644 board/freescale/t2080qds/tlb.c
 create mode 100644 include/configs/T2080QDS.h
arch/powerpc/include/asm/config_mpc85xx.h +1 -0
index 8400f71..cc10d19 100644
@@ -724,6 +724,7 @@
 #define CONFIG_SYS_FSL_CLUSTER_CLOCKS   { 2 }
 #define CONFIG_SYS_FSL_SRDS_1
 #define CONFIG_SYS_FSL_PCI_VER_3_X
+#define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33
 #if defined(CONFIG_PPC_T2080)
 #define CONFIG_SYS_NUM_FM1_DTSEC	8
 #define CONFIG_SYS_NUM_FM1_10GEC	4
board/freescale/t2080qds/Makefile new file +13 -0
new file mode 100644
index 0000000..fdf35f1
@@ -0,0 +1,13 @@
+#
+# Copyright 2013 Freescale Semiconductor, Inc.
+#
+# SPDX-License-Identifier:      GPL-2.0+
+#
+
+obj-$(CONFIG_T2080QDS) += t2080qds.o
+obj-$(CONFIG_T2080QDS) += eth_t2080qds.o
+obj-$(CONFIG_PCI)      += pci.o
+obj-y   += ddr.o
+obj-y   += law.o
+obj-y   += tlb.o
+
board/freescale/t2080qds/ddr.c new file +127 -0

127 lines not on this page · raw message

board/freescale/t2080qds/ddr.h new file +85 -0

85 lines not on this page · raw message

board/freescale/t2080qds/eth_t2080qds.c new file +514 -0

514 lines not on this page · raw message

board/freescale/t2080qds/law.c new file +34 -0
new file mode 100644
index 0000000..74e2a53
@@ -0,0 +1,34 @@
+/*
+ * Copyright 2008-2012 Freescale Semiconductor, Inc.
+ *
+ * (C) Copyright 2000
+ * Wolfgang Denk, DENX Software Engineering, [email protected].
+ *
+ * SPDX-License-Identifier:     GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/fsl_law.h>
+#include <asm/mmu.h>
+
+struct law_entry law_table[] = {
+	SET_LAW(CONFIG_SYS_FLASH_BASE_PHYS, LAW_SIZE_256M, LAW_TRGT_IF_IFC),
+#ifdef CONFIG_SYS_BMAN_MEM_PHYS
+	SET_LAW(CONFIG_SYS_BMAN_MEM_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_BMAN),
+#endif
+#ifdef CONFIG_SYS_QMAN_MEM_PHYS
+	SET_LAW(CONFIG_SYS_QMAN_MEM_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_QMAN),
+#endif
+#ifdef QIXIS_BASE_PHYS
+	SET_LAW(QIXIS_BASE_PHYS, LAW_SIZE_4K, LAW_TRGT_IF_IFC),
+#endif
+#ifdef CONFIG_SYS_DCSRBAR_PHYS
+	/* Limit DCSR to 32M to access NPC Trace Buffer */
+	SET_LAW(CONFIG_SYS_DCSRBAR_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_DCSR),
+#endif
+#ifdef CONFIG_SYS_NAND_BASE_PHYS
+	SET_LAW(CONFIG_SYS_NAND_BASE_PHYS, LAW_SIZE_1M, LAW_TRGT_IF_IFC),
+#endif
+};
+
+int num_law_entries = ARRAY_SIZE(law_table);
board/freescale/t2080qds/pci.c new file +23 -0
new file mode 100644
index 0000000..84a89da
@@ -0,0 +1,23 @@
+/*
+ * Copyright 2007-2013 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <command.h>
+#include <pci.h>
+#include <asm/fsl_pci.h>
+#include <libfdt.h>
+#include <fdt_support.h>
+#include <asm/fsl_serdes.h>
+
+void pci_init_board(void)
+{
+	fsl_pcie_init_board(0);
+}
+
+void pci_of_setup(void *blob, bd_t *bd)
+{
+	FT_FSL_PCI_SETUP;
+}
board/freescale/t2080qds/t2080qds.c new file +327 -0

327 lines not on this page · raw message

board/freescale/t2080qds/t2080qds.h new file +13 -0
new file mode 100644
index 0000000..39fcef2
@@ -0,0 +1,13 @@
+/*
+ * Copyright 2011-2013 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef __CORENET_DS_H__
+#define __CORENET_DS_H__
+
+void fdt_fixup_board_enet(void *blob);
+void pci_of_setup(void *blob, bd_t *bd);
+
+#endif
board/freescale/t2080qds/t2080qds_qixis.h new file +47 -0

47 lines not on this page · raw message

board/freescale/t2080qds/tlb.c new file +146 -0

146 lines not on this page · raw message

boards.cfg +5 -0
index caba64e..79515b8 100644
@@ -963,6 +963,11 @@ Active  powerpc     mpc85xx        -           freescale       t4qds
 Active  powerpc     mpc85xx        -           freescale       t4qds               T4240QDS_SPIFLASH                    T4240QDS:PPC_T4240,RAMBOOT_PBL,SPIFLASH,SYS_TEXT_BASE=0xFFF80000                                                                  -
 Active  powerpc     mpc85xx        -           freescale       t4qds               T4240QDS_SRIO_PCIE_BOOT              T4240QDS:PPC_T4240,SRIO_PCIE_BOOT_SLAVE,SYS_TEXT_BASE=0xFFF80000                                                                  -
 Active  powerpc     mpc85xx        -           freescale       t1040qds            T1040QDS                             T1040QDS:PPC_T1040                                                                                                                Naveen Burmi <[email protected]>
+Active  powerpc     mpc85xx        -           freescale       t2080qds            T2080QDS          T2080QDS:PPC_T2080
+Active  powerpc     mpc85xx        -           freescale       t2080qds            T2080QDS_SDCARD   T2080QDS:PPC_T2080,RAMBOOT_PBL,SDCARD,SYS_TEXT_BASE=0xFFF80000
+Active  powerpc     mpc85xx        -           freescale       t2080qds            T2080QDS_SPIFLASH T2080QDS:PPC_T2080,RAMBOOT_PBL,SPIFLASH,SYS_TEXT_BASE=0xFFF80000
+Active  powerpc     mpc85xx        -           freescale       t2080qds            T2080QDS_NAND     T2080QDS:PPC_T2080,RAMBOOT_PBL,NAND,SYS_TEXT_BASE=0xFFF80000
+Active  powerpc     mpc85xx        -           freescale       t2080qds            T2080QDS_SRIO_PCIE_BOOT T2080QDS:PPC_T2080,SRIO_PCIE_BOOT_SLAVE,SYS_TEXT_BASE=0xFFF80000
 Active  powerpc     mpc85xx        -           gdsys           p1022               controlcenterd_36BIT_SDCARD          controlcenterd:36BIT,SDCARD                                                                                                       Dirk Eibach <[email protected]>
 Active  powerpc     mpc85xx        -           gdsys           p1022               controlcenterd_36BIT_SDCARD_DEVELOP  controlcenterd:36BIT,SDCARD,DEVELOP                                                                                               Dirk Eibach <[email protected]>
 Active  powerpc     mpc85xx        -           gdsys           p1022               controlcenterd_TRAILBLAZER           controlcenterd:TRAILBLAZER,SPIFLASH                                                                                               Dirk Eibach <[email protected]>
include/configs/T2080QDS.h new file +806 -0

806 lines not on this page · raw message

Signature · 1 line
1.8.0
#1 lore raw

PATCH 3/4 powerpc/t2080qds: add support for t2080qds board

Dear Shengzhou Liu,

Quoted 2 lines · In message <[email protected]> you…

The T2080QDS is a high-performance computing evaluation, development and test platform supporting the T2080 QorIQ Power Architecture processor.

This commit has a number of checkpatch warnings (Avoid unnecessary line continuations, quoted string split across lines) that need to be fixed.

Best regards,

Wolfgang Denk

Signature · 4 lines
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
Be kind to unkind people - they need it the most.
#2 lore raw

PATCH 3/4 powerpc/t2080qds: add support for t2080qds board

In reply to Shengzhou Liu
Quoted 42 lines · Shengzhou Liu

The T2080QDS is a high-performance computing evaluation, development and test platform supporting the T2080 QorIQ Power Architecture processor.

T2080QDS feature overview
Processor:
- T2080 SoC integrating four 64-bit dual-threads e6500 cores up to 1.8GHz
Memory:
- Single memory controller capable of supporting DDR3 and DDR3-LV devices
- Two DDR3 DIMMs up to 4GB, Dual rank @ 2133MT/s and ECC support
Ethernet interfaces:
- Two 1Gbps RGMII on-board ports
- Four 10Gbps XFI on-board cages
- 1Gbps/2.5Gbps SGMII Riser card
- 10Gbps XAUI Riser card
Accelerator:
- DPAA components consist of FMan, BMan, QMan, PME, DCE and SEC
SerDes:
- 16 lanes up to 10.3125GHz
- Supports Aurora debug, PEX, SATA, SGMII, sRIO, HiGig, XFI and XAUI
IFC:
- 128MB NOR Flash, 512MB NAND Flash, PromJet debug port and FPGA
eSPI:
- Three SPI flash (16MB N25Q128A + 16MB EN25S64 + 512KB SST25WF040)
USB:
- Two USB2.0 ports with internal PHY (one Type-A + one micro Type-AB)
PCIE:
- Four PCI Express controllers (two PCIe 2.0 and two PCIe 3.0 with SR-IOV)
SATA:
- Two SATA 2.0 ports on-board
SRIO:
- Two Serial RapidIO 2.0 ports up to 5 GHz
eSDHC:
- Supports SD/SDHC/SDXC/eMMC Card
I2C:
- Four I2C controllers.
UART:
- Dual 4-pins UART serial ports
System Logic:
- QIXIS-II FPGA system controll
Debug Features:
- Support Legacy, COP/JTAG, Aurora, Event and EVT

Quoted 3 lines

---
Against master branch of upstream.

Clearly you are sharing most code between T2080 and T2081. I have seen conditional code for CONFIG_PPC_T2081, but I don't see where this macro is defined. Do you plan to post T2081QDS as a separated patch, or you missed it in this one?

York