ahci: imx: Pull out the clock enable/disable calls
Subsystems (7)
PATCH 1/5 ahci: imx: Pull out the clock enable/disable calls
The same code for enabling and disabling SATA clock was found in multiple places in the driver. Implement functions that enable/disable the SATA clock and use them in such places instead of duplicating the code.
--- drivers/ata/ahci_imx.c | 133 ++++++++++++++++++++++++++++--------------------- 1 file changed, 75 insertions(+), 58 deletions(-)
drivers/ata/ahci_imx.c +75 -58
@@ -47,6 +47,73 @@ static int ahci_imx_hotplug;module_param_named (hotplug, ahci_imx_hotplug, int,0644 );MODULE_PARM_DESC (hotplug,"AHCI IMX hot-plug support (0=Don't support, 1=support)" ); +static int imx_sata_clock_enable (struct device *dev,bool config) +{ +struct imx_ahci_priv *imxpriv =dev_get_drvdata (dev->parent); +int ret; + + imxpriv->gpr = +syscon_regmap_lookup_by_compatible ("fsl,imx6q-iomuxc-gpr" ); +if (IS_ERR (imxpriv->gpr)) { +dev_err (dev,"failed to find fsl,imx6q-iomux-gpr regmap\n" ); +return PTR_ERR (imxpriv->gpr); + } + + ret =clk_prepare_enable (imxpriv->sata_ref_clk); +if (ret <0 ) { +dev_err (dev,"prepare-enable sata_ref clock err:%d\n" , ret); +return ret; + } + +/* +* set PHY Paremeters, two steps to configure the GPR13, +* one write for rest of parameters, mask of first write +* is 0x07fffffd, and the other one write for setting +* the mpll_clk_en. +*/ +if (config) { +regmap_update_bits (imxpriv->gpr,IOMUXC_GPR13 , +IMX6Q_GPR13_SATA_RX_EQ_VAL_MASK + |IMX6Q_GPR13_SATA_RX_LOS_LVL_MASK + |IMX6Q_GPR13_SATA_RX_DPLL_MODE_MASK + |IMX6Q_GPR13_SATA_SPD_MODE_MASK + |IMX6Q_GPR13_SATA_MPLL_SS_EN + |IMX6Q_GPR13_SATA_TX_ATTEN_MASK + |IMX6Q_GPR13_SATA_TX_BOOST_MASK + |IMX6Q_GPR13_SATA_TX_LVL_MASK + |IMX6Q_GPR13_SATA_TX_EDGE_RATE + ,IMX6Q_GPR13_SATA_RX_EQ_VAL_3_0_DB + |IMX6Q_GPR13_SATA_RX_LOS_LVL_SATA2M + |IMX6Q_GPR13_SATA_RX_DPLL_MODE_2P_4F + |IMX6Q_GPR13_SATA_SPD_MODE_3P0G + |IMX6Q_GPR13_SATA_MPLL_SS_EN + |IMX6Q_GPR13_SATA_TX_ATTEN_9_16 + |IMX6Q_GPR13_SATA_TX_BOOST_3_33_DB + |IMX6Q_GPR13_SATA_TX_LVL_1_025_V ); + } +regmap_update_bits (imxpriv->gpr,IOMUXC_GPR13 , +IMX6Q_GPR13_SATA_MPLL_CLK_EN , +IMX6Q_GPR13_SATA_MPLL_CLK_EN ); + + ret =clk_prepare_enable (imxpriv->sata_ref_clk); +if (ret <0 ) { +dev_err (dev,"prepare-enable sata_ref clock err:%d\n" , ret); +return ret; + } + +return 0 ; +} + +static void imx_sata_clock_disable (struct device *dev) +{ +struct imx_ahci_priv *imxpriv =dev_get_drvdata (dev->parent); + +regmap_update_bits (imxpriv->gpr,IOMUXC_GPR13 , +IMX6Q_GPR13_SATA_MPLL_CLK_EN , + !IMX6Q_GPR13_SATA_MPLL_CLK_EN ); +clk_disable_unprepare (imxpriv->sata_ref_clk); +} +static void ahci_imx_error_handler (struct ata_port *ap) {u32 reg_val;
@@ -72,10 +139,7 @@ static void ahci_imx_error_handler(struct ata_port *ap)*/ reg_val =readl (mmio +PORT_PHY_CTL );writel (reg_val |PORT_PHY_CTL_PDDQ_LOC , mmio +PORT_PHY_CTL ); -regmap_update_bits (imxpriv->gpr,IOMUXC_GPR13 , -IMX6Q_GPR13_SATA_MPLL_CLK_EN , - !IMX6Q_GPR13_SATA_MPLL_CLK_EN ); -clk_disable_unprepare (imxpriv->sata_ref_clk); +imx_sata_clock_disable (ap->dev); imxpriv->no_device = true; }
@@ -97,44 +161,10 @@ static int imx6q_sata_init(struct device *dev, void __iomem *mmio)unsigned int reg_val;struct imx_ahci_priv *imxpriv =dev_get_drvdata (dev->parent); - imxpriv->gpr = -syscon_regmap_lookup_by_compatible ("fsl,imx6q-iomuxc-gpr" ); -if (IS_ERR (imxpriv->gpr)) { -dev_err (dev,"failed to find fsl,imx6q-iomux-gpr regmap\n" ); -return PTR_ERR (imxpriv->gpr); - } - - ret =clk_prepare_enable (imxpriv->sata_ref_clk); -if (ret <0 ) { -dev_err (dev,"prepare-enable sata_ref clock err:%d\n" , ret); + ret =imx_sata_clock_enable (dev, true); +if (ret <0 )return ret; - } -/* -* set PHY Paremeters, two steps to configure the GPR13, -* one write for rest of parameters, mask of first write -* is 0x07fffffd, and the other one write for setting -* the mpll_clk_en. -*/ -regmap_update_bits (imxpriv->gpr,0x34 ,IMX6Q_GPR13_SATA_RX_EQ_VAL_MASK - |IMX6Q_GPR13_SATA_RX_LOS_LVL_MASK - |IMX6Q_GPR13_SATA_RX_DPLL_MODE_MASK - |IMX6Q_GPR13_SATA_SPD_MODE_MASK - |IMX6Q_GPR13_SATA_MPLL_SS_EN - |IMX6Q_GPR13_SATA_TX_ATTEN_MASK - |IMX6Q_GPR13_SATA_TX_BOOST_MASK - |IMX6Q_GPR13_SATA_TX_LVL_MASK - |IMX6Q_GPR13_SATA_TX_EDGE_RATE - ,IMX6Q_GPR13_SATA_RX_EQ_VAL_3_0_DB - |IMX6Q_GPR13_SATA_RX_LOS_LVL_SATA2M - |IMX6Q_GPR13_SATA_RX_DPLL_MODE_2P_4F - |IMX6Q_GPR13_SATA_SPD_MODE_3P0G - |IMX6Q_GPR13_SATA_MPLL_SS_EN - |IMX6Q_GPR13_SATA_TX_ATTEN_9_16 - |IMX6Q_GPR13_SATA_TX_BOOST_3_33_DB - |IMX6Q_GPR13_SATA_TX_LVL_1_025_V ); -regmap_update_bits (imxpriv->gpr,0x34 ,IMX6Q_GPR13_SATA_MPLL_CLK_EN , -IMX6Q_GPR13_SATA_MPLL_CLK_EN );usleep_range (100 ,200 );/*
@@ -163,11 +193,7 @@ static int imx6q_sata_init(struct device *dev, void __iomem *mmio)static void imx6q_sata_exit (struct device *dev) { -struct imx_ahci_priv *imxpriv =dev_get_drvdata (dev->parent); - -regmap_update_bits (imxpriv->gpr,0x34 ,IMX6Q_GPR13_SATA_MPLL_CLK_EN , - !IMX6Q_GPR13_SATA_MPLL_CLK_EN ); -clk_disable_unprepare (imxpriv->sata_ref_clk); +imx_sata_clock_disable (dev); }static int imx_ahci_suspend (struct device *dev)
@@ -178,12 +204,8 @@ static int imx_ahci_suspend(struct device *dev)* If no_device is set, The CLKs had been gated off in the * initialization so don't do it again here. */ -if (!imxpriv->no_device) { -regmap_update_bits (imxpriv->gpr,IOMUXC_GPR13 , -IMX6Q_GPR13_SATA_MPLL_CLK_EN , - !IMX6Q_GPR13_SATA_MPLL_CLK_EN ); -clk_disable_unprepare (imxpriv->sata_ref_clk); - } +if (!imxpriv->no_device) +imx_sata_clock_disable (dev);return 0 ; }
@@ -194,15 +216,10 @@ static int imx_ahci_resume(struct device *dev)int ret;if (!imxpriv->no_device) { - ret =clk_prepare_enable (imxpriv->sata_ref_clk); -if (ret <0 ) { -dev_err (dev,"pre-enable sata_ref clock err:%d\n" , ret); + ret =imx_sata_clock_enable (dev, false); +if (ret <0 )return ret; - } -regmap_update_bits (imxpriv->gpr,IOMUXC_GPR13 , -IMX6Q_GPR13_SATA_MPLL_CLK_EN , -IMX6Q_GPR13_SATA_MPLL_CLK_EN );usleep_range (1000 ,2000 ); }
Signature · 1 line
1.8.4.2
PATCH 2/5 ahci: imx: Add i.MX53 support
Add minor adjustments to support i.MX53 SATA port as well as i.MX6Q one. The difference here is mostly the clock which need to be enabled and also the lack of need of programming IOMUXC registers on i.MX53. All of which is well handles in the clock enable/disable functions. Note that this patch also cleans up the names of the common functions, so they don't read imx6q_* but imx_* instead.
--- drivers/ata/ahci_imx.c | 198 ++++++++++++++++++++++++++++++++----------------- 1 file changed, 128 insertions(+), 70 deletions(-)
drivers/ata/ahci_imx.c +128 -70
@@ -34,10 +34,23 @@ enum { HOST_TIMER1MS = 0xe0, /* Timer 1-ms */ }; +enum ahci_imx_type { +AHCI_IMX53 , +AHCI_IMX6Q , +}; +struct imx_ahci_priv {struct platform_device *ahci_pdev; +enum ahci_imx_type type; + +/* i.MX53 clock */ +struct clk *sata_gate_clk; +struct clk *sata_phy_clk; +/* i.MX6Q clock */ struct clk *sata_ref_clk; +/* Common clock */ struct clk *ahb_clk; +struct regmap *gpr;bool no_device;bool first_time;
@@ -52,53 +65,73 @@ static int imx_sata_clock_enable(struct device *dev, bool config)struct imx_ahci_priv *imxpriv =dev_get_drvdata (dev->parent);int ret; - imxpriv->gpr = -syscon_regmap_lookup_by_compatible ("fsl,imx6q-iomuxc-gpr" ); -if (IS_ERR (imxpriv->gpr)) { -dev_err (dev,"failed to find fsl,imx6q-iomux-gpr regmap\n" ); -return PTR_ERR (imxpriv->gpr); - } - - ret =clk_prepare_enable (imxpriv->sata_ref_clk); -if (ret <0 ) { -dev_err (dev,"prepare-enable sata_ref clock err:%d\n" , ret); -return ret; - } +if (imxpriv->type ==AHCI_IMX53 ) { + ret =clk_prepare_enable (imxpriv->sata_gate_clk); +if (ret <0 ) { +dev_err (dev,"prepare-enable sata_gate clock err:%d\n" , + ret); +return ret; + } -/* -* set PHY Paremeters, two steps to configure the GPR13, -* one write for rest of parameters, mask of first write -* is 0x07fffffd, and the other one write for setting -* the mpll_clk_en. -*/ -if (config) { + ret =clk_prepare_enable (imxpriv->sata_phy_clk); +if (ret <0 ) { +clk_disable_unprepare (imxpriv->sata_gate_clk); +dev_err (dev,"prepare-enable sata_phy clock err:%d\n" , + ret); +return ret; + } + }else if (imxpriv->type ==AHCI_IMX6Q ) { + imxpriv->gpr =syscon_regmap_lookup_by_compatible ( +"fsl,imx6q-iomuxc-gpr" ); +if (IS_ERR (imxpriv->gpr)) { +dev_err (dev, +"failed to find fsl,imx6q-iomux-gpr regmap\n" ); +return PTR_ERR (imxpriv->gpr); + } + + ret =clk_prepare_enable (imxpriv->sata_ref_clk); +if (ret <0 ) { +dev_err (dev,"prepare-enable sata_ref clock err:%d\n" , + ret); +return ret; + } + +/* +* set PHY Paremeters, two steps to configure the GPR13, +* one write for rest of parameters, mask of first write +* is 0x07fffffd, and the other one write for setting +* the mpll_clk_en. +*/ +if (config) { +regmap_update_bits (imxpriv->gpr,IOMUXC_GPR13 , +IMX6Q_GPR13_SATA_RX_EQ_VAL_MASK + |IMX6Q_GPR13_SATA_RX_LOS_LVL_MASK + |IMX6Q_GPR13_SATA_RX_DPLL_MODE_MASK + |IMX6Q_GPR13_SATA_SPD_MODE_MASK + |IMX6Q_GPR13_SATA_MPLL_SS_EN + |IMX6Q_GPR13_SATA_TX_ATTEN_MASK + |IMX6Q_GPR13_SATA_TX_BOOST_MASK + |IMX6Q_GPR13_SATA_TX_LVL_MASK + |IMX6Q_GPR13_SATA_TX_EDGE_RATE + ,IMX6Q_GPR13_SATA_RX_EQ_VAL_3_0_DB + |IMX6Q_GPR13_SATA_RX_LOS_LVL_SATA2M + |IMX6Q_GPR13_SATA_RX_DPLL_MODE_2P_4F + |IMX6Q_GPR13_SATA_SPD_MODE_3P0G + |IMX6Q_GPR13_SATA_MPLL_SS_EN + |IMX6Q_GPR13_SATA_TX_ATTEN_9_16 + |IMX6Q_GPR13_SATA_TX_BOOST_3_33_DB + |IMX6Q_GPR13_SATA_TX_LVL_1_025_V ); + }regmap_update_bits (imxpriv->gpr,IOMUXC_GPR13 , -IMX6Q_GPR13_SATA_RX_EQ_VAL_MASK - |IMX6Q_GPR13_SATA_RX_LOS_LVL_MASK - |IMX6Q_GPR13_SATA_RX_DPLL_MODE_MASK - |IMX6Q_GPR13_SATA_SPD_MODE_MASK - |IMX6Q_GPR13_SATA_MPLL_SS_EN - |IMX6Q_GPR13_SATA_TX_ATTEN_MASK - |IMX6Q_GPR13_SATA_TX_BOOST_MASK - |IMX6Q_GPR13_SATA_TX_LVL_MASK - |IMX6Q_GPR13_SATA_TX_EDGE_RATE - ,IMX6Q_GPR13_SATA_RX_EQ_VAL_3_0_DB - |IMX6Q_GPR13_SATA_RX_LOS_LVL_SATA2M - |IMX6Q_GPR13_SATA_RX_DPLL_MODE_2P_4F - |IMX6Q_GPR13_SATA_SPD_MODE_3P0G - |IMX6Q_GPR13_SATA_MPLL_SS_EN - |IMX6Q_GPR13_SATA_TX_ATTEN_9_16 - |IMX6Q_GPR13_SATA_TX_BOOST_3_33_DB - |IMX6Q_GPR13_SATA_TX_LVL_1_025_V ); - } -regmap_update_bits (imxpriv->gpr,IOMUXC_GPR13 , -IMX6Q_GPR13_SATA_MPLL_CLK_EN , -IMX6Q_GPR13_SATA_MPLL_CLK_EN ); +IMX6Q_GPR13_SATA_MPLL_CLK_EN , +IMX6Q_GPR13_SATA_MPLL_CLK_EN ); - ret =clk_prepare_enable (imxpriv->sata_ref_clk); -if (ret <0 ) { -dev_err (dev,"prepare-enable sata_ref clock err:%d\n" , ret); -return ret; + ret =clk_prepare_enable (imxpriv->sata_ref_clk); +if (ret <0 ) { +dev_err (dev,"prepare-enable sata_ref clock err:%d\n" , + ret); +return ret; + } }return 0 ;
@@ -108,10 +141,15 @@ static void imx_sata_clock_disable(struct device *dev) {struct imx_ahci_priv *imxpriv =dev_get_drvdata (dev->parent); -regmap_update_bits (imxpriv->gpr,IOMUXC_GPR13 , -IMX6Q_GPR13_SATA_MPLL_CLK_EN , - !IMX6Q_GPR13_SATA_MPLL_CLK_EN ); -clk_disable_unprepare (imxpriv->sata_ref_clk); +if (imxpriv->type ==AHCI_IMX53 ) { +clk_disable_unprepare (imxpriv->sata_phy_clk); +clk_disable_unprepare (imxpriv->sata_gate_clk); + }else if (imxpriv->type ==AHCI_IMX6Q ) { +regmap_update_bits (imxpriv->gpr,IOMUXC_GPR13 , +IMX6Q_GPR13_SATA_MPLL_CLK_EN , + !IMX6Q_GPR13_SATA_MPLL_CLK_EN ); +clk_disable_unprepare (imxpriv->sata_ref_clk); + } }static void ahci_imx_error_handler (struct ata_port *ap)
@@ -155,7 +193,7 @@ static const struct ata_port_info ahci_imx_port_info = { .port_ops = &ahci_imx_ops, }; -static int imx6q_sata_init (struct device *dev,void __iomem *mmio) +static int imx_sata_init (struct device *dev,void __iomem *mmio) {int ret =0 ;unsigned int reg_val;
@@ -191,7 +229,7 @@ static int imx6q_sata_init(struct device *dev, void __iomem *mmio)return 0 ; } -static void imx6q_sata_exit (struct device *dev) +static void imx_sata_exit (struct device *dev) {imx_sata_clock_disable (dev); }
@@ -226,16 +264,18 @@ static int imx_ahci_resume(struct device *dev)return 0 ; } -static struct ahci_platform_data imx6q_sata_pdata = { - .init = imx6q_sata_init, - .exit = imx6q_sata_exit, - .ata_port_info = &ahci_imx_port_info, - .suspend = imx_ahci_suspend, - .resume = imx_ahci_resume, +static struct ahci_platform_data imx_sata_pdata = { + .init = imx_sata_init, + .exit = imx_sata_exit, + .ata_port_info = &ahci_imx_port_info, + .suspend = imx_ahci_suspend, + .resume = imx_ahci_resume, + };static const struct of_device_id imx_ahci_of_match[] = { - { .compatible ="fsl,imx6q-ahci" , .data = &imx6q_sata_pdata}, + { .compatible ="fsl,imx53-ahci" , .data = (void *)AHCI_IMX53 }, + { .compatible ="fsl,imx6q-ahci" , .data = (void *)AHCI_IMX6Q }, {}, };MODULE_DEVICE_TABLE (of, imx_ahci_of_match);
@@ -245,12 +285,20 @@ static int imx_ahci_probe(struct platform_device *pdev)struct device *dev = &pdev->dev;struct resource *mem, *irq, res[2 ];const struct of_device_id *of_id; +enum ahci_imx_type type;const struct ahci_platform_data *pdata =NULL ;struct imx_ahci_priv *imxpriv;struct device *ahci_dev;struct platform_device *ahci_pdev;int ret; + of_id =of_match_device (imx_ahci_of_match, dev); +if (!of_id) +return -EINVAL ; + + type = (enum ahci_imx_type )of_id->data; + pdata = &imx_sata_pdata; + imxpriv =devm_kzalloc (dev,sizeof (*imxpriv),GFP_KERNEL );if (!imxpriv) {dev_err (dev,"can't alloc ahci_host_priv\n" );
@@ -266,6 +314,8 @@ static int imx_ahci_probe(struct platform_device *pdev) imxpriv->no_device = false; imxpriv->first_time = true; + imxpriv->type = type; + imxpriv->ahb_clk =devm_clk_get (dev,"ahb" );if (IS_ERR (imxpriv->ahb_clk)) {dev_err (dev,"can't get ahb clock.\n" );
@@ -273,24 +323,32 @@ static int imx_ahci_probe(struct platform_device *pdev) goto err_out; } - imxpriv->sata_ref_clk =devm_clk_get (dev,"sata_ref" ); -if (IS_ERR (imxpriv->sata_ref_clk)) { -dev_err (dev,"can't get sata_ref clock.\n" ); - ret =PTR_ERR (imxpriv->sata_ref_clk); - goto err_out; +if (type ==AHCI_IMX53 ) { + imxpriv->sata_gate_clk =devm_clk_get (dev,"sata_gate" ); +if (IS_ERR (imxpriv->sata_gate_clk)) { +dev_err (dev,"can't get sata_gate clock.\n" ); + ret =PTR_ERR (imxpriv->sata_gate_clk); + goto err_out; + } + + imxpriv->sata_phy_clk =devm_clk_get (dev,"sata_phy" ); +if (IS_ERR (imxpriv->sata_phy_clk)) { +dev_err (dev,"can't get sata_phy clock.\n" ); + ret =PTR_ERR (imxpriv->sata_phy_clk); + goto err_out; + } + }else if (type ==AHCI_IMX6Q ) { + imxpriv->sata_ref_clk =devm_clk_get (dev,"sata_ref" ); +if (IS_ERR (imxpriv->sata_ref_clk)) { +dev_err (dev,"can't get sata_ref clock.\n" ); + ret =PTR_ERR (imxpriv->sata_ref_clk); + goto err_out; + } } imxpriv->ahci_pdev = ahci_pdev;platform_set_drvdata (pdev, imxpriv); - of_id =of_match_device (imx_ahci_of_match, dev); -if (of_id) { - pdata = of_id->data; - }else { - ret = -EINVAL ; - goto err_out; - } - mem =platform_get_resource (pdev,IORESOURCE_MEM ,0 ); irq =platform_get_resource (pdev,IORESOURCE_IRQ ,0 );if (!mem || !irq) {
Signature · 1 line
1.8.4.2
PATCH 3/5 ARM: imx: imx53: Add SATA PHY clock
In reply to Marek VasutAdd SATA PHY clock which are derived from the USB PHY1 clock. Note that this patch derives the SATA PHY clock from USB PHY1 clock gate so that the SATA driver can ungate both the SATA PHY clock and USB PHY1 clock for the SATA to work correctly.
--- Documentation/devicetree/bindings/clock/imx5-clock.txt | 1 + arch/arm/mach-imx/clk-imx51-imx53.c | 3 ++- 2 files changed, 3 insertions(+), 1 deletion(-)
Documentation/devicetree/bindings/clock/imx5-clock.txt +1 -0
@@ -199,6 +199,7 @@ clocks and IDs. spdif_ipg_gate 185 ocram 186 sahara_ipg_gate 187 + sata_phy 188 Examples (for mx53):
arch/arm/mach-imx/clk-imx51-imx53.c +2 -1
@@ -122,7 +122,7 @@ enum imx5_clks { srtc_gate, pata_gate, sata_gate, spdif_xtal_sel, spdif0_sel, spdif1_sel, spdif0_pred, spdif0_podf, spdif1_pred, spdif1_podf, spdif0_com_s, spdif1_com_sel, spdif0_gate, spdif1_gate, spdif_ipg_gate, - ocram, sahara_ipg_gate, clk_max + ocram, sahara_ipg_gate, sata_phy, clk_max };static struct clk *clk[clk_max];
@@ -588,6 +588,7 @@ static void __init mx53_clocks_init(struct device_node *np) clk[cko2] =imx_clk_gate2 ("cko2" ,"cko2_podf" ,MXC_CCM_CCOSR ,24 ); clk[spdif_xtal_sel] =imx_clk_mux ("spdif_xtal_sel" ,MXC_CCM_CSCMR1 ,2 ,2 , mx53_spdif_xtal_sel,ARRAY_SIZE (mx53_spdif_xtal_sel)); + clk[sata_phy] =imx_clk_fixed_factor ("sata_phy" ,"usb_phy1_gate" ,1 ,1 );for (i =0 ; i <ARRAY_SIZE (clk); i++)if (IS_ERR (clk[i]))
Signature · 1 line
1.8.4.2
PATCH 4/5 ARM: dts: imx53: Add AHCI SATA binding
In reply to Marek VasutThe AHCI-IMX driver now supports i.MX53 as well. Add DT binding.
--- arch/arm/boot/dts/imx53.dtsi | 9 +++++++++ 1 file changed, 9 insertions(+)
arch/arm/boot/dts/imx53.dtsi +9 -0
@@ -85,6 +85,15 @@ interrupt-parent = <&tzic>; ranges; + sata: sata at 10000000 { + compatible = "fsl,imx53-ahci"; + reg = <0x10000000 0x1000>; + interrupts = <28>; + clocks = <&clks 173>, <&clks 188>, <&clks 5>; + clock-names = "sata_gate", "sata_phy", "ahb"; + status = "disabled"; + }; + ipu: ipu at 18000000 { #crtc-cells = <1>; compatible = "fsl,imx53-ipu";
Signature · 1 line
1.8.4.2
PATCH 4/5 ARM: dts: imx53: Add AHCI SATA binding
Quoted 1 line · Marek Vasut
The AHCI-IMX driver now supports i.MX53 as well. Add DT binding.
I think this patch can be merged independently without the driver changes in place. Also, I understand that the term 'binding' is referred as binding doc, while what you're patching here is device tree source.
Shawn
Quoted 33 lines
Signed-off-by Marek Vasut <[email protected]>Cc Shawn Guo <[email protected]>Cc Richard Zhu <[email protected]>Cc Tejun Heo <[email protected]>Cc Linux-IDE <[email protected]>--- arch/arm/boot/dts/imx53.dtsi | 9 +++++++++ 1 file changed, 9 insertions(+)arch/arm/boot/dts/imx53.dtsi +9
-0@@ -85,6 +85,15 @@ interrupt-parent = <&tzic>; ranges; + sata: sata@10000000 { + compatible = "fsl,imx53-ahci"; + reg = <0x10000000 0x1000>; + interrupts = <28>; + clocks = <&clks 173>, <&clks 188>, <&clks 5>; + clock-names = "sata_gate", "sata_phy", "ahb"; + status = "disabled"; + }; + ipu: ipu@18000000 { #crtc-cells = <1>; compatible = "fsl,imx53-ipu";Signature · 1 line
1.8.4.2
PATCH 4/5 ARM: dts: imx53: Add AHCI SATA binding
Dear Shawn Guo,
Quoted 7 lines · Marek Vasut
Quoted 1 line
The AHCI-IMX driver now supports i.MX53 as well. Add DT binding.
I think this patch can be merged independently without the driver changes in place. Also, I understand that the term 'binding' is referred as binding doc, while what you're patching here is device tree source.
Ah right, shall I change it?
Best regards,
Marek Vasut
PATCH 5/5 ARM: dts: imx53: Enable AHCI SATA for M53EVK
In reply to Marek Vasut--- arch/arm/boot/dts/imx53-m53evk.dts | 4 ++++ 1 file changed, 4 insertions(+)
arch/arm/boot/dts/imx53-m53evk.dts +4 -0
@@ -44,6 +44,10 @@ }; }; }; + + sata at 10000000 { + status = "okay"; + }; }; backlight {
Signature · 1 line
1.8.4.2
PATCH 5/5 ARM: dts: imx53: Enable AHCI SATA for M53EVK
Quoted 14 lines · Marek Vasut
Signed-off-by Marek Vasut <[email protected]>Cc Shawn Guo <[email protected]>Cc Richard Zhu <[email protected]>Cc Tejun Heo <[email protected]>Cc Linux-IDE <[email protected]>--- arch/arm/boot/dts/imx53-m53evk.dts | 4 ++++ 1 file changed, 4 insertions(+)arch/arm/boot/dts/imx53-m53evk.dts +0
-0
arch/arm/boot/dts/imx53-m53evk.dts line 50
Quoted 7 lines
arch/arm/boot/dts/imx53-m53evk.dts +4
-0@@ -44,6 +44,10 @@ }; }; }; + + sata@10000000 { + status = "okay"; + };
Why not
&sata {
status = "okay"; };
just like what other devices in this file are doing?
Shawn
PATCH 1/5 ahci: imx: Pull out the clock enable/disable calls
In reply to Marek VasutHi,
Quoted 48 lines · Marek Vasut
The same code for enabling and disabling SATA clock was found in multiple places in the driver. Implement functions that enable/disable the SATA clock and use them in such places instead of duplicating the code.
Signed-off-by Marek Vasut <[email protected]>Cc Shawn Guo <[email protected]>Cc Richard Zhu <[email protected]>Cc Tejun Heo <[email protected]>Cc Linux-IDE <[email protected]>--- drivers/ata/ahci_imx.c | 133 ++++++++++++++++++++++++++++--------------------- 1 file changed, 75 insertions(+), 58 deletions(-)drivers/ata/ahci_imx.c +27
-0@@ -47,6 +47,73 @@ static int ahci_imx_hotplug;module_param_named (hotplug, ahci_imx_hotplug, int,0644 );MODULE_PARM_DESC (hotplug,"AHCI IMX hot-plug support (0=Don't support, 1=support)" ); +static int imx_sata_clock_enable (struct device *dev,bool config) +{ +struct imx_ahci_priv *imxpriv =dev_get_drvdata (dev->parent); +int ret; + + imxpriv->gpr = +syscon_regmap_lookup_by_compatible ("fsl,imx6q-iomuxc-gpr" ); +if (IS_ERR (imxpriv->gpr)) { +dev_err (dev,"failed to find fsl,imx6q-iomux-gpr regmap\n" ); +return PTR_ERR (imxpriv->gpr); + } + + ret =clk_prepare_enable (imxpriv->sata_ref_clk); +if (ret <0 ) { +dev_err (dev,"prepare-enable sata_ref clock err:%d\n" , ret); +return ret; + } + +/* +* set PHY Paremeters, two steps to configure the GPR13, +* one write for rest of parameters, mask of first write +* is 0x07fffffd, and the other one write for setting +* the mpll_clk_en. +*/ +if (config) { +regmap_update_bits (imxpriv->gpr,IOMUXC_GPR13 , + IMX6Q_GPR13_SATA_RX_EQ_VAL_MASK
drivers/ata/ahci_imx.c static int ahci_imx_hotplug; · line 86
Quoted 10 lines
drivers/ata/ahci_imx.c +9
-0+ | IMX6Q_GPR13_SATA_RX_LOS_LVL_MASK + |IMX6Q_GPR13_SATA_RX_DPLL_MODE_MASK + |IMX6Q_GPR13_SATA_SPD_MODE_MASK + |IMX6Q_GPR13_SATA_MPLL_SS_EN + |IMX6Q_GPR13_SATA_TX_ATTEN_MASK + |IMX6Q_GPR13_SATA_TX_BOOST_MASK + |IMX6Q_GPR13_SATA_TX_LVL_MASK + |IMX6Q_GPR13_SATA_TX_EDGE_RATE + ,IMX6Q_GPR13_SATA_RX_EQ_VAL_3_0_DB
I would prefer the comma to be at the end of the line where one usually looks for it. Also '#define'ing constants for these bitmasks would make the code more readable.
Lothar Wa?mann
Signature · 9 lines
___________________________________________________________ Ka-Ro electronics GmbH | Pascalstra?e 22 | D - 52076 Aachen Phone: +49 2408 1402-0 | Fax: +49 2408 1402-10 Gesch?ftsf?hrer: Matthias Kaussen Handelsregistereintrag: Amtsgericht Aachen, HRB 4996 www.karo-electronics.de | info at karo-electronics.de ___________________________________________________________
PATCH 1/5 ahci: imx: Pull out the clock enable/disable calls
In reply to Marek VasutHi Marek,
Quoted 19 lines · Marek Vasut
The same code for enabling and disabling SATA clock was found in multiple places in the driver. Implement functions that enable/disable the SATA clock and use them in such places instead of duplicating the code.
Signed-off-by Marek Vasut <[email protected]>Cc Shawn Guo <[email protected]>Cc Richard Zhu <[email protected]>Cc Tejun Heo <[email protected]>Cc Linux-IDE <[email protected]>--- drivers/ata/ahci_imx.c | 133 ++++++++++++++++++++++++++++--------------------- 1 file changed, 75 insertions(+), 58 deletions(-)drivers/ata/ahci_imx.c +0
-0
drivers/ata/ahci_imx.c static int ahci_imx_hotplug; · line 49
Quoted 4 lines
drivers/ata/ahci_imx.c +0
-0@@ -47,6 +47,73 @@ static int ahci_imx_hotplug;module_param_named (hotplug, ahci_imx_hotplug, int,0644 );MODULE_PARM_DESC (hotplug,"AHCI IMX hot-plug support (0=Don't support, 1=support)" );
I haven't traced through all of this, but if you're copying from the Freescale 3.0.35 kernel, note that there's a bug in it, and the 0x7FFFFFFD really wanted to be an 0x7FFFFFFF.
The way I read this comment, the writes need to happen in two steps:
- write everything with the PHY disabled
- enable the PHY
We had reports of stalls waiting for SATA drives to be enumerated that were solved with this commit...
https://github.com/boundarydevices/linux-imx6/commit/0186ea224ce6bd1cb4757a0f83b0090e26a021f4
Quoted 20 lines
drivers/ata/ahci_imx.c +20
-0+/* +* set PHY Paremeters, two steps to configure the GPR13, +* one write for rest of parameters, mask of first write +* is 0x07fffffd, and the other one write for setting +* the mpll_clk_en. +*/ +if (config) { +regmap_update_bits (imxpriv->gpr,IOMUXC_GPR13 , +IMX6Q_GPR13_SATA_RX_EQ_VAL_MASK + |IMX6Q_GPR13_SATA_RX_LOS_LVL_MASK + |IMX6Q_GPR13_SATA_RX_DPLL_MODE_MASK + |IMX6Q_GPR13_SATA_SPD_MODE_MASK + |IMX6Q_GPR13_SATA_MPLL_SS_EN + |IMX6Q_GPR13_SATA_TX_ATTEN_MASK + |IMX6Q_GPR13_SATA_TX_BOOST_MASK + |IMX6Q_GPR13_SATA_TX_LVL_MASK + |IMX6Q_GPR13_SATA_TX_EDGE_RATE + ,IMX6Q_GPR13_SATA_RX_EQ_VAL_3_0_DB + |IMX6Q_GPR13_SATA_RX_LOS_LVL_SATA2M + | IMX6Q_GPR13_SATA_RX_DPLL_MODE_2P_4F
drivers/ata/ahci_imx.c static int ahci_imx_hotplug; · line 97
Quoted 10 lines
drivers/ata/ahci_imx.c +10
-0+ | IMX6Q_GPR13_SATA_SPD_MODE_3P0G + |IMX6Q_GPR13_SATA_MPLL_SS_EN + |IMX6Q_GPR13_SATA_TX_ATTEN_9_16 + |IMX6Q_GPR13_SATA_TX_BOOST_3_33_DB + | IMX6Q_GPR13_SATA_TX_LVL_1_025_V); + } +regmap_update_bits (imxpriv->gpr,IOMUXC_GPR13 , +IMX6Q_GPR13_SATA_MPLL_CLK_EN , +IMX6Q_GPR13_SATA_MPLL_CLK_EN ); +
Regards,
Eric
PATCH 1/5 ahci: imx: Pull out the clock enable/disable calls
Hi Eric,
Quoted 28 lines
Hi Marek,
Quoted 25 lines · Marek Vasut
The same code for enabling and disabling SATA clock was found in multiple places in the driver. Implement functions that enable/disable the SATA clock and use them in such places instead of duplicating the code.
Signed-off-by Marek Vasut <[email protected]>Cc Shawn Guo <[email protected]>Cc Richard Zhu <[email protected]>Cc Tejun Heo <[email protected]>Cc Linux-IDE <[email protected]>---
drivers/ata/ahci_imx.c | 133++++++++++++++++++++++++++++--------------------- 1 file changed, 75 insertions(+), 58 deletions(-)
drivers/ata/ahci_imx.c +0
-0@@ -47,6 +47,73 @@ static int ahci_imx_hotplug;module_param_named (hotplug, ahci_imx_hotplug, int,0644 );MODULE_PARM_DESC (hotplug,"AHCI IMX hot-plug support (0=Don't support, 1=support)");
Quoted 5 lines
Quoted 1 line
<snip>
I haven't traced through all of this, but if you're copying from the Freescale 3.0.35 kernel, note that there's a bug in it, and the
0x7FFFFFFDreally wanted to be an0x7FFFFFFF.
I'm not taking this from FSL 3.0.35, no, but thanks for pointing this out!
Quoted 9 lines
The way I read this comment, the writes need to happen in two steps:
- write everything with the PHY disabled
- enable the PHYWe had reports of stalls waiting for SATA drives to be enumerated that were solved with this commit...
imx6/commit/0186ea224ce6bd1cb4757
Quoted 1 line
a0f83b0090e26a021f4
[...]
Quoted 3 lines
drivers/ata/ahci_imx.c static int ahci_imx_hotplug; · line 96
Quoted 3 lines
drivers/ata/ahci_imx.c +3
-0+regmap_update_bits (imxpriv->gpr,IOMUXC_GPR13 , +IMX6Q_GPR13_SATA_MPLL_CLK_EN , +IMX6Q_GPR13_SATA_MPLL_CLK_EN );
Isn't this snippet doing exactly what your patch does ?
PATCH 1/5 ahci: imx: Pull out the clock enable/disable calls
Hi Marek,
Quoted 50 lines · Marek Vasut
Hi Eric,
Quoted 28 lines
Hi Marek,
Quoted 25 lines · Marek Vasut
The same code for enabling and disabling SATA clock was found in multiple places in the driver. Implement functions that enable/disable the SATA clock and use them in such places instead of duplicating the code.
Signed-off-by Marek Vasut <[email protected]>Cc Shawn Guo <[email protected]>Cc Richard Zhu <[email protected]>Cc Tejun Heo <[email protected]>Cc Linux-IDE <[email protected]>---
drivers/ata/ahci_imx.c | 133++++++++++++++++++++++++++++--------------------- 1 file changed, 75 insertions(+), 58 deletions(-)
drivers/ata/ahci_imx.c +0
-0@@ -47,6 +47,73 @@ static int ahci_imx_hotplug;module_param_named (hotplug, ahci_imx_hotplug, int,0644 );MODULE_PARM_DESC (hotplug,"AHCI IMX hot-plug support (0=Don't support, 1=support)");Quoted 5 lines
Quoted 1 line
<snip>
I haven't traced through all of this, but if you're copying from the Freescale 3.0.35 kernel, note that there's a bug in it, and the
0x7FFFFFFDreally wanted to be an0x7FFFFFFF.I'm not taking this from FSL 3.0.35, no, but thanks for pointing this out!
Quoted 9 lines
The way I read this comment, the writes need to happen in two steps:
- write everything with the PHY disabled
- enable the PHYWe had reports of stalls waiting for SATA drives to be enumerated that were solved with this commit...
imx6/commit/0186ea224ce6bd1cb4757
Quoted 1 line
a0f83b0090e26a021f4
Quoted 8 lines
[...]
Quoted 3 lines
drivers/ata/ahci_imx.c static int ahci_imx_hotplug; · line 96
Quoted 3 lines
drivers/ata/ahci_imx.c +3
-0+regmap_update_bits (imxpriv->gpr,IOMUXC_GPR13 , +IMX6Q_GPR13_SATA_MPLL_CLK_EN , +IMX6Q_GPR13_SATA_MPLL_CLK_EN );Isn't this snippet doing exactly what your patch does ?
This part is doing the "set the bit" part:
https://github.com/boundarydevices/linux-imx6/blob/boundary-imx_3.0.35_4.1.0/arch/arm/mach-mx6/board-mx6_nitrogen6x.c#L728
The previous block isn't clearing the enable bit though:
+ regmap_update_bits(imxpriv->gpr, IOMUXC_GPR13,
+ IMX6Q_GPR13_SATA_RX_EQ_VAL_MASK
+ | IMX6Q_GPR13_SATA_RX_LOS_LVL_MASK + | IMX6Q_GPR13_SATA_RX_DPLL_MODE_MASK + | IMX6Q_GPR13_SATA_SPD_MODE_MASK + | IMX6Q_GPR13_SATA_MPLL_SS_EN + | IMX6Q_GPR13_SATA_TX_ATTEN_MASK + | IMX6Q_GPR13_SATA_TX_BOOST_MASK + | IMX6Q_GPR13_SATA_TX_LVL_MASK + | IMX6Q_GPR13_SATA_TX_EDGE_RATE + , IMX6Q_GPR13_SATA_RX_EQ_VAL_3_0_DB + | IMX6Q_GPR13_SATA_RX_LOS_LVL_SATA2M + | IMX6Q_GPR13_SATA_RX_DPLL_MODE_2P_4F + | IMX6Q_GPR13_SATA_SPD_MODE_3P0G + | IMX6Q_GPR13_SATA_MPLL_SS_EN + | IMX6Q_GPR13_SATA_TX_ATTEN_9_16 + | IMX6Q_GPR13_SATA_TX_BOOST_3_33_DB + | IMX6Q_GPR13_SATA_TX_LVL_1_025_V);
The explicit clearing of bit 1 is what was necessary (and I think it's what the original author was after).
This was a hard one to find, because it seems that it only shows up on some boards, and most of the time on those boards.
Here are some references:
http://boundarydevices.com/freescale-ubuntu-image-with-4-0-0-kernel/#comment-60464 http://boundarydevices.com/debian-installer-on-i-mx6-boards/#comment-76203
The symptom is (was) that U-Boot worked 100% of the time, but the kernel failed to find the drive.
Using 'mm' in U-Boot to clear the bit before kernel launch also allowed things to function.
Regards,
Eric
PATCH 1/5 ahci: imx: Pull out the clock enable/disable calls
Hi Nelson:
Quoted 108 lines
-----Original Message-----
From: linux-ide-owner at vger.kernel.org [mailto:linux-ide-owner at vger.kernel.org] On Behalf Of Eric Nelson
Sent: Tuesday, November 19, 2013 6:12 AM
To: Marek Vasut
Cc: linux-arm-kernel at lists.infradead.org; Zhu Richard-R65037; Tejun Heo; Shawn Guo; Linux-IDE
Subject: Re: [PATCH 1/5] ahci: imx: Pull out the clock enable/disable callsHi Marek,
Quoted 8 lines · Marek Vasut
Hi Eric,
Quoted 6 lines
Hi Marek,
Quoted 3 lines · Marek Vasut
The same code for enabling and disabling SATA clock was found in multiple places in the driver. Implement functions that enable/disable the SATA clock and use them in such places instead of
duplicating the code.
Quoted 42 lines
Quoted 22 lines
Quoted 22 lines
Signed-off-by Marek Vasut <[email protected]>Cc Shawn Guo <[email protected]>Cc Richard Zhu <[email protected]>Cc Tejun Heo <[email protected]>Cc Linux-IDE <[email protected]>---
drivers/ata/ahci_imx.c | 133++++++++++++++++++++++++++++--------------------- 1 file changed, 75 insertions(+), 58 deletions(-)
drivers/ata/ahci_imx.c index renamed from drivers/ata/ahci_imx.c +0
-0ae2d73f..c7ee505 100644
drivers/ata/ahci_imx.c +0
-0@@ -47,6 +47,73 @@ static int ahci_imx_hotplug;module_param_named (hotplug, ahci_imx_hotplug, int,0644 );MODULE_PARM_DESC (hotplug,"AHCI IMX hot-plug support (0=Don't support, 1=support)");Quoted 5 lines
Quoted 1 line
<snip>
I haven't traced through all of this, but if you're copying from the Freescale 3.0.35 kernel, note that there's a bug in it, and the
0x7FFFFFFDreally wanted to be an0x7FFFFFFF.I'm not taking this from FSL 3.0.35, no, but thanks for pointing this out!
Quoted 9 lines
The way I read this comment, the writes need to happen in two steps:
- write everything with the PHY disabled
- enable the PHYWe had reports of stalls waiting for SATA drives to be enumerated that were solved with this commit...
imx6/commit/0186ea224ce6bd1cb4757
Quoted 1 line
a0f83b0090e26a021f4Quoted 8 lines
[...]
Quoted 3 lines
drivers/ata/ahci_imx.c static int ahci_imx_hotplug; · line 96
Quoted 3 lines
drivers/ata/ahci_imx.c +3
-0+regmap_update_bits (imxpriv->gpr,IOMUXC_GPR13 , +IMX6Q_GPR13_SATA_MPLL_CLK_EN , +IMX6Q_GPR13_SATA_MPLL_CLK_EN );Isn't this snippet doing exactly what your patch does ?
This part is doing the "set the bit" part:
https://github.com/boundarydevices/linux-imx6/blob/boundary-
imx_3.0.35_4.1.0/arch/arm/mach-mx6/board-mx6_nitrogen6x.c#L728The previous block isn't clearing the enable bit though:
drivers/ata/ahci_imx.c +18
-0+regmap_update_bits (imxpriv->gpr,IOMUXC_GPR13 , +IMX6Q_GPR13_SATA_RX_EQ_VAL_MASK + |IMX6Q_GPR13_SATA_RX_LOS_LVL_MASK + |IMX6Q_GPR13_SATA_RX_DPLL_MODE_MASK + |IMX6Q_GPR13_SATA_SPD_MODE_MASK + |IMX6Q_GPR13_SATA_MPLL_SS_EN + |IMX6Q_GPR13_SATA_TX_ATTEN_MASK + |IMX6Q_GPR13_SATA_TX_BOOST_MASK + |IMX6Q_GPR13_SATA_TX_LVL_MASK + |IMX6Q_GPR13_SATA_TX_EDGE_RATE + ,IMX6Q_GPR13_SATA_RX_EQ_VAL_3_0_DB + |IMX6Q_GPR13_SATA_RX_LOS_LVL_SATA2M + |IMX6Q_GPR13_SATA_RX_DPLL_MODE_2P_4F + |IMX6Q_GPR13_SATA_SPD_MODE_3P0G + |IMX6Q_GPR13_SATA_MPLL_SS_EN + |IMX6Q_GPR13_SATA_TX_ATTEN_9_16 + |IMX6Q_GPR13_SATA_TX_BOOST_3_33_DB + |IMX6Q_GPR13_SATA_TX_LVL_1_025_V );The explicit clearing of bit 1 is what was necessary (and I think it's what the original author was after).
This was a hard one to find, because it seems that it only shows up on some boards, and most of the time on those boards.
Here are some references:
http://boundarydevices.com/freescale-ubuntu-image-with-4-0-0-
kernel/#comment-60464
http://boundarydevices.com/debian-installer-on-i-mx6-boards/#comment-
76203
Quoted 6 lines
The symptom is (was) that U-Boot worked 100% of the time, but the kernel failed to find the drive.
Using 'mm' in U-Boot to clear the bit before kernel launch also allowed things to function.
[Richard] Agree to explicit clearing of bit1, refer to the chapter "Power-Up Sequences" of "Serial Advanced Technology Attachment PHY (SATA PHY)" in iMX6 RM doc.
Quoted 8 lines
Regards,
Eric
--
To unsubscribe from this list: send the line "unsubscribe linux-ide" in the body of a message to majordomo at vger.kernel.org More majordomo info at
http://vger.kernel.org/majordomo-info.html
Best Regards
Richard Zhu
PATCH 1/5 ahci: imx: Pull out the clock enable/disable calls
In reply to Eric NelsonDear Eric Nelson,
Quoted 60 lines
Hi Marek,
Quoted 57 lines · Marek Vasut
Hi Eric,
Quoted 29 lines
Hi Marek,
Quoted 26 lines · Marek Vasut
The same code for enabling and disabling SATA clock was found in multiple places in the driver. Implement functions that enable/disable the SATA clock and use them in such places instead of duplicating the code.
Signed-off-by Marek Vasut <[email protected]>Cc Shawn Guo <[email protected]>Cc Richard Zhu <[email protected]>Cc Tejun Heo <[email protected]>Cc Linux-IDE <[email protected]>---
drivers/ata/ahci_imx.c | 133++++++++++++++++++++++++++++--------------------- 1 file changed, 75 insertions(+), 58 deletions(-)
drivers/ata/ahci_imx.c +0
-0@@ -47,6 +47,73 @@ static int ahci_imx_hotplug;module_param_named (hotplug, ahci_imx_hotplug, int,0644 ); MODULE_PARM_DESC(hotplug, "AHCI IMX hot-plug support (0=Don't support, 1=support)");Quoted 5 lines
Quoted 1 line
<snip>
I haven't traced through all of this, but if you're copying from the Freescale 3.0.35 kernel, note that there's a bug in it, and the
0x7FFFFFFDreally wanted to be an0x7FFFFFFF.I'm not taking this from FSL 3.0.35, no, but thanks for pointing this out!
Quoted 10 lines
The way I read this comment, the writes need to happen in two
steps:
- write everything with the PHY disabled
- enable the PHYWe had reports of stalls waiting for SATA drives to be enumerated that were solved with this commit...
imx6/commit/0186ea224ce6bd1cb4757
Quoted 1 line
a0f83b0090e26a021f4[...]
Quoted 8 lines
Quoted 5 lines
Quoted 3 lines
drivers/ata/ahci_imx.c static int ahci_imx_hotplug; · line 96
Quoted 3 lines
drivers/ata/ahci_imx.c +3
-0+regmap_update_bits (imxpriv->gpr,IOMUXC_GPR13 , +IMX6Q_GPR13_SATA_MPLL_CLK_EN , +IMX6Q_GPR13_SATA_MPLL_CLK_EN );Isn't this snippet doing exactly what your patch does ?
This part is doing the "set the bit" part:
https://github.com/boundarydevices/linux-imx6/blob/boundary-
imx_3.0.35_4.1
Quoted 23 lines
.0/arch/arm/mach-mx6/board-mx6_nitrogen6x.c#L728
The previous block isn't clearing the enable bit though:
drivers/ata/ahci_imx.c +18
-0+regmap_update_bits (imxpriv->gpr,IOMUXC_GPR13 , +IMX6Q_GPR13_SATA_RX_EQ_VAL_MASK + |IMX6Q_GPR13_SATA_RX_LOS_LVL_MASK + |IMX6Q_GPR13_SATA_RX_DPLL_MODE_MASK + |IMX6Q_GPR13_SATA_SPD_MODE_MASK + |IMX6Q_GPR13_SATA_MPLL_SS_EN + |IMX6Q_GPR13_SATA_TX_ATTEN_MASK + |IMX6Q_GPR13_SATA_TX_BOOST_MASK + |IMX6Q_GPR13_SATA_TX_LVL_MASK + |IMX6Q_GPR13_SATA_TX_EDGE_RATE + ,IMX6Q_GPR13_SATA_RX_EQ_VAL_3_0_DB + |IMX6Q_GPR13_SATA_RX_LOS_LVL_SATA2M + |IMX6Q_GPR13_SATA_RX_DPLL_MODE_2P_4F + |IMX6Q_GPR13_SATA_SPD_MODE_3P0G + |IMX6Q_GPR13_SATA_MPLL_SS_EN + |IMX6Q_GPR13_SATA_TX_ATTEN_9_16 + |IMX6Q_GPR13_SATA_TX_BOOST_3_33_DB + |IMX6Q_GPR13_SATA_TX_LVL_1_025_V );
Quoted 8 lines
The explicit clearing of bit 1 is what was necessary (and I think it's what the original author was after).
This was a hard one to find, because it seems that it only shows up on some boards, and most of the time on those boards.
Here are some references:
http://boundarydevices.com/freescale-ubuntu-image-with-4-0-0-
kernel/#comme
Quoted 8 lines
nt-60464
http://boundarydevices.com/debian-installer-on-i-mx6-boards/#comment-76203The symptom is (was) that U-Boot worked 100% of the time, but the kernel failed to find the drive.
Using 'mm' in U-Boot to clear the bit before kernel launch also allowed things to function.
Ah, now I see it. I will cook a patch, thanks!