ARM: dts: imx53: Add USB support for M53EVK
Subsystems (2)
PATCH 1/1 ARM: dts: imx53: Add USB support for M53EVK
Add USB support for M53EVK. The configuration is such that USB Host1 port is used as Host and the USB OTG port is used as Peripheral thus far. Once OTG is properly fixed, the OTG will be further adjusted.
--- arch/arm/boot/dts/imx53-m53evk.dts | 22 ++++++++++++++++++++++ 1 file changed, 22 insertions(+)
arch/arm/boot/dts/imx53-m53evk.dts +22 -0
@@ -100,6 +100,15 @@ regulator-always-on; }; + reg_usbh1_vbus: regulator at 3 { + compatible = "regulator-fixed"; + reg = <3>; + regulator-name = "vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio1 2 0>; + enable-active-low; + }; }; sound {
@@ -228,6 +237,8 @@ MX53_PAD_GPIO_0__CCM_SSI_EXT1_CLK 0x80000000 MX53_PAD_EIM_EB3__GPIO2_31 0x80000000 MX53_PAD_PATA_DA_0__GPIO7_6 0x80000000 + MX53_PAD_GPIO_2__GPIO1_2 0x80000000 + MX53_PAD_GPIO_3__USBOH3_USBH1_OC 0x80000000 >; };
@@ -332,3 +343,14 @@ pinctrl-0 = <&pinctrl_uart3>; status = "okay"; }; + +&usbotg { + dr_mode = "peripheral"; + status = "okay"; +}; + +&usbh1 { + vbus-supply = <®_usbh1_vbus>; + phy_type = "utmi"; + status = "okay"; +};
Signature · 1 line
1.8.4.2
PATCH 1/1 ARM: dts: imx53: Add USB support for M53EVK
Quoted 5 lines · Marek Vasut
arch/arm/boot/dts/imx53-m53evk.dts +1
-0@@ -332,3 +343,14 @@ pinctrl-0 = <&pinctrl_uart3>; status = "okay"; }; +
arch/arm/boot/dts/imx53-m53evk.dts line 356
Quoted 10 lines
arch/arm/boot/dts/imx53-m53evk.dts +10
-0+&usbotg { + dr_mode = "peripheral"; + status = "okay"; +}; + +&usbh1 { + vbus-supply = <®_usbh1_vbus>; + phy_type = "utmi"; + status = "okay"; +};
To maintain the alphabetical order, 'usbh1' should be put before 'usbotg'. I just fixed it up and applied the patch.
Shawn
PATCH 1/1 ARM: dts: imx53: Add USB support for M53EVK
Hi Shawn,
Quoted 8 lines · Marek Vasut
Quoted 7 lines
arch/arm/boot/dts/imx53-m53evk.dts +0
-0@@ -332,3 +343,14 @@ pinctrl-0 = <&pinctrl_uart3>; status = "okay"; };
Quoted 14 lines
arch/arm/boot/dts/imx53-m53evk.dts line 356
Quoted 11 lines
arch/arm/boot/dts/imx53-m53evk.dts +11
-0+ +&usbotg { + dr_mode = "peripheral"; + status = "okay"; +}; + +&usbh1 { + vbus-supply = <®_usbh1_vbus>; + phy_type = "utmi"; + status = "okay"; +};To maintain the alphabetical order, 'usbh1' should be put before 'usbotg'. I just fixed it up and applied the patch.
Ah, you're right. Thank you and sorry for adding more burden unto you.
Best regards,
Marek Vasut