pcm051: Support for revision 3
PATCH 1/1 pcm051: Support for revision 3
From: Lars Poeschel <[email protected]>
Phytec sells revision or version 3 of pcm051. It is labeled 1358.3 on the board. The difference for u-boot is that is has other DDR3 RAM on it:
1 x MT41K256M16HA125E instead of 2 x MT41J256M8HX15E on revisions 1 and
2. Both configurations are 512 MiB.
Configure your u-boot build with pcm051_rev3 for the new RAM and pcm051_rev1 for the old RAM configuration. Board revision 2 has to use pcm051_rev1 also.
--- board/phytec/pcm051/board.c | 53 ++++++++++++++++++++++++++++++++++++++++----- boards.cfg | 3 ++- 2 files changed, 49 insertions(+), 7 deletions(-)
board/phytec/pcm051/board.c +47 -6
@@ -49,6 +49,7 @@ const struct dpll_params *get_dpll_ddr_params(void)return &dpll_ddr; } +#ifdef CONFIG_REV1 static const struct ddr_data ddr3_data = { .datardsratio0 =MT41J256M8HX15E_RD_DQS , .datawdsratio0 = MT41J256M8HX15E_WR_DQS,
@@ -82,6 +83,52 @@ static struct emif_regs ddr3_emif_reg_data = { PHY_EN_DYN_PWRDN, }; +void sdram_init (void ) +{ +config_ddr (DDR_CLK_MHZ ,MT41J256M8HX15E_IOCTRL_VALUE , &ddr3_data, + &ddr3_cmd_ctrl_data, &ddr3_emif_reg_data,0 ); +} +#else +static const struct ddr_data ddr3_data = { + .datardsratio0 =MT41K256M16HA125E_RD_DQS , + .datawdsratio0 =MT41K256M16HA125E_WR_DQS , + .datafwsratio0 =MT41K256M16HA125E_PHY_FIFO_WE , + .datawrsratio0 =MT41K256M16HA125E_PHY_WR_DATA , + .datadldiff0 =PHY_DLL_LOCK_DIFF , +}; + +static const struct cmd_control ddr3_cmd_ctrl_data = { + .cmd0csratio =MT41K256M16HA125E_RATIO , + .cmd0dldiff =MT41K256M16HA125E_DLL_LOCK_DIFF , + .cmd0iclkout =MT41K256M16HA125E_INVERT_CLKOUT , + + .cmd1csratio =MT41K256M16HA125E_RATIO , + .cmd1dldiff =MT41K256M16HA125E_DLL_LOCK_DIFF , + .cmd1iclkout =MT41K256M16HA125E_INVERT_CLKOUT , + + .cmd2csratio =MT41K256M16HA125E_RATIO , + .cmd2dldiff =MT41K256M16HA125E_DLL_LOCK_DIFF , + .cmd2iclkout =MT41K256M16HA125E_INVERT_CLKOUT , +}; + +static struct emif_regs ddr3_emif_reg_data = { + .sdram_config =MT41K256M16HA125E_EMIF_SDCFG , + .ref_ctrl =MT41K256M16HA125E_EMIF_SDREF , + .sdram_tim1 =MT41K256M16HA125E_EMIF_TIM1 , + .sdram_tim2 =MT41K256M16HA125E_EMIF_TIM2 , + .sdram_tim3 =MT41K256M16HA125E_EMIF_TIM3 , + .zq_config =MT41K256M16HA125E_ZQ_CFG , + .emif_ddr_phy_ctlr_1 =MT41K256M16HA125E_EMIF_READ_LATENCY | +PHY_EN_DYN_PWRDN , +}; + +void sdram_init (void ) +{ +config_ddr (DDR_CLK_MHZ ,MT41K256M16HA125E_IOCTRL_VALUE , &ddr3_data, + &ddr3_cmd_ctrl_data, &ddr3_emif_reg_data,0 ); +} +#endif +void set_uart_mux_conf (void ) {enable_uart0_pin_mux ();
@@ -95,12 +142,6 @@ void set_mux_conf_regs(void) enable_board_pin_mux(); } - -void sdram_init (void ) -{ -config_ddr (DDR_CLK_MHZ ,MT41J256M8HX15E_IOCTRL_VALUE , &ddr3_data, - &ddr3_cmd_ctrl_data, &ddr3_emif_reg_data,0 ); -}#endif /*
boards.cfg +2 -1
@@ -244,7 +244,8 @@ Active arm armv7 - armltd vexpress Active arm armv7 - armltd vexpress vexpress_ca5x2 - Matt Waddel <[email protected]> Active arm armv7 - armltd vexpress vexpress_ca9x4 - Matt Waddel <[email protected]> Active arm armv7 am33xx isee igep0033 igep0033 - Enric Balletbo i Serra <[email protected]> -Active arm armv7 am33xx phytec pcm051 pcm051 pcm051 Lars Poeschel <[email protected]> +Active arm armv7 am33xx phytec pcm051 pcm051_rev1 pcm051:REV1 Lars Poeschel <[email protected]> +Active arm armv7 am33xx phytec pcm051 pcm051_rev3 pcm051:REV3 Lars Poeschel <[email protected]> Active arm armv7 am33xx siemens dxr2 dxr2 - Roger Meier <[email protected]> Active arm armv7 am33xx siemens pxm2 pxm2 - Roger Meier <[email protected]> Active arm armv7 am33xx siemens rut rut - Roger Meier <[email protected]>
Signature · 1 line
1.8.4.2
PATCH 1/1 pcm051: Support for revision 3
Quoted 11 lines · Lars Poeschel
From: Lars Poeschel <[email protected]>
Phytec sells revision or version 3 of pcm051. It is labeled 1358.3 on the board. The difference for u-boot is that is has other DDR3 RAM on it:
1 x MT41K256M16HA125E instead of 2 x MT41J256M8HX15E on revisions 1 and
2. Both configurations are 512 MiB.
Configure your u-boot build withpcm051_rev3for the new RAM andpcm051_rev1for the old RAM configuration. Board revision 2 has to usepcm051_rev1also.Signed-off-by Lars Poeschel <[email protected]>
Is there no run-time way to tell if we're on rev1/2/3?
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: not available Type: application/pgp-signature Size: 836 bytes Desc: Digital signature URL: <http://lists.denx.de/pipermail/u-boot/attachments/20131119/1e711fce/attachment.pgp>
PATCH 1/1 pcm051: Support for revision 3
Am Dienstag, 19. November 2013, 15:08:27 schrieb Tom Rini:
Quoted 11 lines · Lars Poeschel
Quoted 10 lines
From: Lars Poeschel <[email protected]>
Phytec sells revision or version 3 of pcm051. It is labeled 1358.3 on the board. The difference for u-boot is that is has other DDR3 RAM on it:
1 x MT41K256M16HA125E instead of 2 x MT41J256M8HX15E on revisions 1 and
2. Both configurations are 512 MiB.
Configure your u-boot build withpcm051_rev3for the new RAM andpcm051_rev1for the old RAM configuration. Board revision 2 has to usepcm051_rev1also.
Quoted 3 lines
Quoted 1 line
Signed-off-by Lars Poeschel <[email protected]>Is there no run-time way to tell if we're on rev1/2/3?
Unfortunately I am not aware of a 100% bullet proof one.
One way would be to read the AM3359 silicon ID. I have two boards here: rev1 and rev3. The phytec rev3 board has a newer silicon on it. I don't know about rev2's silicon ID. And I am not sure if the rev3 silicon change directly corresponds to the DDR RAM change and if all rev3 boards have the new silicon. What I know for sure is that the RAM change was with rev3. Nevertheless phytec itself supplies a patched barebox as bootloader. And they have a compile time config option for different RAM configurations of the board. And they even seem to have more RAM configurations than the two I have seen yet.
Lars
PATCH 1/1 pcm051: Support for revision 3
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1
Quoted 16 lines · Lars Poeschel
Am Dienstag, 19. November 2013, 15:08:27 schrieb Tom Rini:
Quoted 11 lines · Lars Poeschel
Quoted 10 lines
From: Lars Poeschel <[email protected]>
Phytec sells revision or version 3 of pcm051. It is labeled 1358.3 on the board. The difference for u-boot is that is has other DDR3 RAM on it: 1 x MT41K256M16HA125E instead of 2 x MT41J256M8HX15E on revisions 1 and 2. Both configurations are 512 MiB. Configure your u-boot build with
pcm051_rev3for the new RAM andpcm051_rev1for the old RAM configuration. Board revision 2 has to usepcm051_rev1also.Quoted 3 lines
Quoted 1 line
Signed-off-by Lars Poeschel <[email protected]>Is there no run-time way to tell if we're on rev1/2/3?
Quoted 10 lines
Unfortunately I am not aware of a 100% bullet proof one. One way would be to read the AM3359 silicon ID. I have two boards here:
rev1 and rev3. The phytec rev3 board has a newer silicon on it. I don't know about rev2's silicon ID. And I am not sure if the rev3 silicon change directly corresponds to the DDR RAM change and if all rev3 boards have the new silicon. What I know for sure is that the RAM change was with rev3. Nevertheless phytec itself supplies a patched barebox as bootloader. And they have a compile time config option for different RAM configurations of the board. And they even seem to have more RAM configurations than the two I have seen yet.
OK, thanks.
- --
Tom
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
Comment: Using GnuPG with Thunderbird - http://www.enigmail.net/
iQIcBAEBAgAGBQJSjggcAAoJENk4IS6UOR1WOFcQAJmvkp5P2nkvSRhYAgqupGBL EczfkW/hERfExMHjzas+UUGUcr7WJgX4lnFMZOou0hdTBilkjl4gI1xVQfuoUMQA fw0Gya8R6dI8I9x7rtoFRM69+mbA2HXNei040aqlX7mmqK5BSUA85IFlTUf7//A8 zXsiUDNzze6V0+TvzM/IFdA9ma1aQnNDoiuMEjcwFKC5/d4wgC0Lntx6SfwlFiKD BuddoIglkMHDJ1ZjAhGgrZU0Jt4LuctD+mHRdN4GRo9evO8sXpbDU95ZsEefbza0 eT0mvXXy/gUEg7LUnRmmAKgOstLmX4ttC+9PxMWpmdO4LX8b4zEGPfI3Ev39KTj1 GwiKlmNudhBHIcCgfoj9dYTgXdpgGgw5KVU1sms1Nn/uTEvAG9wVIeiibzzHLmh3 XgibqSjMD3FosqG+tnliELJKnh/yAqpYVAV7ldVpKXP2VeKAdSRHwffTgbkYUYhS KI2G+JXvQjOYS176uTTRkwDwPOSwx8A7cs/fkbTkPyWkzlyzn6ZDemmcLnv48f6F XD+HBtcFpfplAxg4kJ9bws97tKgtYYJK0eoC6C82eM/k8XFkb/lJ7FaLusU4KGtM 4njiBYktv8I3J/kh2fOe2r9ACJpyBJFm+ffFJlN+x1GInMHiJ9tYpDliA0+Pw5Jm vjbvV/rGHT9Lo1o73FUY
=hMkr
-----END PGP SIGNATURE-----
Quoted 11 lines · Lars Poeschel
From: Lars Poeschel <[email protected]>
Phytec sells revision or version 3 of pcm051. It is labeled 1358.3 on the board. The difference for u-boot is that is has other DDR3 RAM on it:
1 x MT41K256M16HA125E instead of 2 x MT41J256M8HX15E on revisions 1 and
2. Both configurations are 512 MiB.
Configure your u-boot build withpcm051_rev3for the new RAM andpcm051_rev1for the old RAM configuration. Board revision 2 has to usepcm051_rev1also.Signed-off-by Lars Poeschel <[email protected]>
Applied to u-boot-ti/master, after adapting to my change about not touching some EMIF4D registers, :thanks!
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: not available Type: application/pgp-signature Size: 836 bytes Desc: Digital signature URL: <http://lists.denx.de/pipermail/u-boot/attachments/20131204/9b82cb6a/attachment.pgp>