Skip to contentSkip to conversation

3.10.22-stable review

PATCH In review Greg Kroah-Hartman 5 participants 180 messages Dec 2, 2013 – Dec 4, 2013 Page 2 of 2

Subsystems (2)
lore
Share & tools
lore
author maintainer
#158 lore raw

PATCH 156/173 media: dvb-frontends: again, Dont use dynamic static allocation

In reply to Greg Kroah-Hartman

3.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Mauro Carvalho Chehab <[email protected]>

commit 8393796dfa4cf5dffcceec464c7789bec3a2f471 upstream.

Dynamic static allocation is evil, as Kernel stack is too low, and
compilation complains about it on some archs:
drivers/media/dvb-frontends/bcm3510.c:230:1: warning: 'bcm3510_do_hab_cmd' uses dynamic stack allocation [enabled by default] drivers/media/dvb-frontends/itd1000.c:69:1: warning: 'itd1000_write_regs.constprop.0' uses dynamic stack allocation [enabled by default] drivers/media/dvb-frontends/mt312.c:126:1: warning: 'mt312_write' uses dynamic stack allocation [enabled by default] drivers/media/dvb-frontends/nxt200x.c:111:1: warning: 'nxt200x_writebytes' uses dynamic stack allocation [enabled by default] drivers/media/dvb-frontends/stb6100.c:216:1: warning: 'stb6100_write_reg_range.constprop.3' uses dynamic stack allocation [enabled by default] drivers/media/dvb-frontends/stv6110.c:98:1: warning: 'stv6110_write_regs' uses dynamic stack allocation [enabled by default] drivers/media/dvb-frontends/stv6110x.c:85:1: warning: 'stv6110x_write_regs' uses dynamic stack allocation [enabled by default] drivers/media/dvb-frontends/tda18271c2dd.c:147:1: warning: 'WriteRegs' uses dynamic stack allocation [enabled by default] drivers/media/dvb-frontends/zl10039.c:119:1: warning: 'zl10039_write' uses dynamic stack allocation [enabled by default]
Instead, let's enforce a limit for the buffer. Considering that I2C
transfers are generally limited, and that devices used on USB has a
max data length of 64 bytes for the control URBs.
So, it seem safe to use 64 bytes as the hard limit for all those devices.
On most cases, the limit is a way lower than that, but this limit
is small enough to not affect the Kernel stack, and it is a no brain
limit, as using smaller ones would require to either carefully each
driver or to take a look on each datasheet.

---
 drivers/media/dvb-frontends/bcm3510.c      |   15 ++++++++++++++-
 drivers/media/dvb-frontends/itd1000.c      |   13 ++++++++++++-
 drivers/media/dvb-frontends/mt312.c        |   10 +++++++++-
 drivers/media/dvb-frontends/nxt200x.c      |   11 ++++++++++-
 drivers/media/dvb-frontends/stb6100.c      |   11 ++++++++++-
 drivers/media/dvb-frontends/stv6110.c      |   12 +++++++++++-
 drivers/media/dvb-frontends/stv6110x.c     |   13 ++++++++++++-
 drivers/media/dvb-frontends/tda18271c2dd.c |   14 ++++++++++++--
 drivers/media/dvb-frontends/zl10039.c      |   12 +++++++++++-
 9 files changed, 101 insertions(+), 10 deletions(-)
drivers/media/dvb-frontends/bcm3510.c +14 -1
@@ -44,6 +44,9 @@
 #include "bcm3510.h"
 #include "bcm3510_priv.h"
 
+/* Max transfer size done by bcm3510_do_hab_cmd() function */
+#define MAX_XFER_SIZE	128
+
 struct bcm3510_state {
 
 	struct i2c_adapter* i2c;
@@ -201,9 +204,19 @@ static int bcm3510_hab_send_request(stru
 
 static int bcm3510_do_hab_cmd(struct bcm3510_state *st, u8 cmd, u8 msgid, u8 *obuf, u8 olen, u8 *ibuf, u8 ilen)
 {
-	u8 ob[olen+2],ib[ilen+2];
+	u8 ob[MAX_XFER_SIZE], ib[MAX_XFER_SIZE];
 	int ret = 0;
 
+	if (ilen + 2 > sizeof(ib)) {
+		deb_hab("do_hab_cmd: ilen=%d is too big!\n", ilen);
+		return -EINVAL;
+	}
+
+	if (olen + 2 > sizeof(ob)) {
+		deb_hab("do_hab_cmd: olen=%d is too big!\n", olen);
+		return -EINVAL;
+	}
+
 	ob[0] = cmd;
 	ob[1] = msgid;
 	memcpy(&ob[2],obuf,olen);
drivers/media/dvb-frontends/itd1000.c +12 -1
@@ -31,6 +31,9 @@
 #include "itd1000.h"
 #include "itd1000_priv.h"
 
+/* Max transfer size done by I2C transfer functions */
+#define MAX_XFER_SIZE  64
+
 static int debug;
 module_param(debug, int, 0644);
 MODULE_PARM_DESC(debug, "Turn on/off debugging (default:off).");
@@ -52,10 +55,18 @@ MODULE_PARM_DESC(debug, "Turn on/off deb
 /* don't write more than one byte with flexcop behind */
 static int itd1000_write_regs(struct itd1000_state *state, u8 reg, u8 v[], u8 len)
 {
-	u8 buf[1+len];
+	u8 buf[MAX_XFER_SIZE];
 	struct i2c_msg msg = {
 		.addr = state->cfg->i2c_address, .flags = 0, .buf = buf, .len = len+1
 	};
+
+	if (1 + len > sizeof(buf)) {
+		printk(KERN_WARNING
+		       "itd1000: i2c wr reg=%04x: len=%d is too big!\n",
+		       reg, len);
+		return -EINVAL;
+	}
+
 	buf[0] = reg;
 	memcpy(&buf[1], v, len);
 
drivers/media/dvb-frontends/mt312.c +9 -1
@@ -36,6 +36,8 @@
 #include "mt312_priv.h"
 #include "mt312.h"
 
+/* Max transfer size done by I2C transfer functions */
+#define MAX_XFER_SIZE  64
 
 struct mt312_state {
 	struct i2c_adapter *i2c;
@@ -96,9 +98,15 @@ static int mt312_write(struct mt312_stat
 		       const u8 *src, const size_t count)
 {
 	int ret;
-	u8 buf[count + 1];
+	u8 buf[MAX_XFER_SIZE];
 	struct i2c_msg msg;
 
+	if (1 + count > sizeof(buf)) {
+		printk(KERN_WARNING
+		       "mt312: write: len=%zd is too big!\n", count);
+		return -EINVAL;
+	}
+
 	if (debug) {
 		int i;
 		dprintk("W(%d):", reg & 0x7f);
drivers/media/dvb-frontends/nxt200x.c +10 -1
@@ -39,6 +39,9 @@
  */
 #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
 
+/* Max transfer size done by I2C transfer functions */
+#define MAX_XFER_SIZE  64
+
 #define NXT2002_DEFAULT_FIRMWARE "dvb-fe-nxt2002.fw"
 #define NXT2004_DEFAULT_FIRMWARE "dvb-fe-nxt2004.fw"
 #define CRC_CCIT_MASK 0x1021
@@ -95,10 +98,16 @@ static int i2c_readbytes(struct nxt200x_
 static int nxt200x_writebytes (struct nxt200x_state* state, u8 reg,
 			       const u8 *buf, u8 len)
 {
-	u8 buf2 [len+1];
+	u8 buf2[MAX_XFER_SIZE];
 	int err;
 	struct i2c_msg msg = { .addr = state->config->demod_address, .flags = 0, .buf = buf2, .len = len + 1 };
 
+	if (1 + len > sizeof(buf2)) {
+		pr_warn("%s: i2c wr reg=%04x: len=%d is too big!\n",
+			 __func__, reg, len);
+		return -EINVAL;
+	}
+
 	buf2[0] = reg;
 	memcpy(&buf2[1], buf, len);
 
drivers/media/dvb-frontends/stb6100.c +10 -1
@@ -31,6 +31,8 @@
 static unsigned int verbose;
 module_param(verbose, int, 0644);
 
+/* Max transfer size done by I2C transfer functions */
+#define MAX_XFER_SIZE  64
 
 #define FE_ERROR		0
 #define FE_NOTICE		1
@@ -183,7 +185,7 @@ static int stb6100_read_reg(struct stb61
 static int stb6100_write_reg_range(struct stb6100_state *state, u8 buf[], int start, int len)
 {
 	int rc;
-	u8 cmdbuf[len + 1];
+	u8 cmdbuf[MAX_XFER_SIZE];
 	struct i2c_msg msg = {
 		.addr	= state->config->tuner_address,
 		.flags	= 0,
@@ -191,6 +193,13 @@ static int stb6100_write_reg_range(struc
 		.len	= len + 1
 	};
 
+	if (1 + len > sizeof(buf)) {
+		printk(KERN_WARNING
+		       "%s: i2c wr: len=%d is too big!\n",
+		       KBUILD_MODNAME, len);
+		return -EINVAL;
+	}
+
 	if (unlikely(start < 1 || start + len > STB6100_NUMREGS)) {
 		dprintk(verbose, FE_ERROR, 1, "Invalid register range %d:%d",
 			start, len);
drivers/media/dvb-frontends/stv6110.c +11 -1
@@ -30,6 +30,9 @@
 
 #include "stv6110.h"
 
+/* Max transfer size done by I2C transfer functions */
+#define MAX_XFER_SIZE  64
+
 static int debug;
 
 struct stv6110_priv {
@@ -68,7 +71,7 @@ static int stv6110_write_regs(struct dvb
 {
 	struct stv6110_priv *priv = fe->tuner_priv;
 	int rc;
-	u8 cmdbuf[len + 1];
+	u8 cmdbuf[MAX_XFER_SIZE];
 	struct i2c_msg msg = {
 		.addr	= priv->i2c_address,
 		.flags	= 0,
@@ -78,6 +81,13 @@ static int stv6110_write_regs(struct dvb
 
 	dprintk("%s\n", __func__);
 
+	if (1 + len > sizeof(cmdbuf)) {
+		printk(KERN_WARNING
+		       "%s: i2c wr: len=%d is too big!\n",
+		       KBUILD_MODNAME, len);
+		return -EINVAL;
+	}
+
 	if (start + len > 8)
 		return -EINVAL;
 
drivers/media/dvb-frontends/stv6110x.c +12 -1
@@ -32,6 +32,9 @@
 #include "stv6110x.h"
 #include "stv6110x_priv.h"
 
+/* Max transfer size done by I2C transfer functions */
+#define MAX_XFER_SIZE  64
+
 static unsigned int verbose;
 module_param(verbose, int, 0644);
 MODULE_PARM_DESC(verbose, "Set Verbosity level");
@@ -61,7 +64,8 @@ static int stv6110x_write_regs(struct st
 {
 	int ret;
 	const struct stv6110x_config *config = stv6110x->config;
-	u8 buf[len + 1];
+	u8 buf[MAX_XFER_SIZE];
+
 	struct i2c_msg msg = {
 		.addr = config->addr,
 		.flags = 0,
@@ -69,6 +73,13 @@ static int stv6110x_write_regs(struct st
 		.len = len + 1
 	};
 
+	if (1 + len > sizeof(buf)) {
+		printk(KERN_WARNING
+		       "%s: i2c wr: len=%d is too big!\n",
+		       KBUILD_MODNAME, len);
+		return -EINVAL;
+	}
+
 	if (start + len > 8)
 		return -EINVAL;
 
drivers/media/dvb-frontends/tda18271c2dd.c +12 -2
@@ -34,6 +34,9 @@
 #include "dvb_frontend.h"
 #include "tda18271c2dd.h"
 
+/* Max transfer size done by I2C transfer functions */
+#define MAX_XFER_SIZE  64
+
 struct SStandardParam {
 	s32   m_IFFrequency;
 	u32   m_BandWidth;
@@ -139,11 +142,18 @@ static int i2c_write(struct i2c_adapter
 static int WriteRegs(struct tda_state *state,
 		     u8 SubAddr, u8 *Regs, u16 nRegs)
 {
-	u8 data[nRegs+1];
+	u8 data[MAX_XFER_SIZE];
+
+	if (1 + nRegs > sizeof(data)) {
+		printk(KERN_WARNING
+		       "%s: i2c wr: len=%d is too big!\n",
+		       KBUILD_MODNAME, nRegs);
+		return -EINVAL;
+	}
 
 	data[0] = SubAddr;
 	memcpy(data + 1, Regs, nRegs);
-	return i2c_write(state->i2c, state->adr, data, nRegs+1);
+	return i2c_write(state->i2c, state->adr, data, nRegs + 1);
 }
 
 static int WriteReg(struct tda_state *state, u8 SubAddr, u8 Reg)
drivers/media/dvb-frontends/zl10039.c +11 -1
@@ -30,6 +30,9 @@
 
 static int debug;
 
+/* Max transfer size done by I2C transfer functions */
+#define MAX_XFER_SIZE  64
+
 #define dprintk(args...) \
 	do { \
 		if (debug) \
@@ -98,7 +101,7 @@ static int zl10039_write(struct zl10039_
 			const enum zl10039_reg_addr reg, const u8 *src,
 			const size_t count)
 {
-	u8 buf[count + 1];
+	u8 buf[MAX_XFER_SIZE];
 	struct i2c_msg msg = {
 		.addr = state->i2c_addr,
 		.flags = 0,
@@ -106,6 +109,13 @@ static int zl10039_write(struct zl10039_
 		.len = count + 1,
 	};
 
+	if (1 + count > sizeof(buf)) {
+		printk(KERN_WARNING
+		       "%s: i2c wr reg=%04x: len=%zd is too big!\n",
+		       KBUILD_MODNAME, reg, count);
+		return -EINVAL;
+	}
+
 	dprintk("%s\n", __func__);
 	/* Write register address and data in one go */
 	buf[0] = reg;
author maintainer
#159 lore raw

PATCH 157/173 media: s5h1420: Dont use dynamic static allocation

In reply to Greg Kroah-Hartman

3.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Mauro Carvalho Chehab <[email protected]>

commit 9736a89dafe07359d9c86bf9c3b815a250b354bc upstream.

Dynamic static allocation is evil, as Kernel stack is too low, and
compilation complains about it on some archs:
drivers/media/dvb-frontends/s5h1420.c:851:1: warning: 's5h1420_tuner_i2c_tuner_xfer' uses dynamic stack allocation [enabled by default]
Instead, let's enforce a limit for the buffer.
In the specific case of this frontend, only ttpci uses it. The maximum
number of messages there is two, on I2C read operations. As the logic
can add an extra operation, change the size to 3.

---
 drivers/media/dvb-frontends/s5h1420.c |   11 +++++++++--
 1 file changed, 9 insertions(+), 2 deletions(-)
drivers/media/dvb-frontends/s5h1420.c +9 -2
@@ -836,9 +836,16 @@ static u32 s5h1420_tuner_i2c_func(struct
 static int s5h1420_tuner_i2c_tuner_xfer(struct i2c_adapter *i2c_adap, struct i2c_msg msg[], int num)
 {
 	struct s5h1420_state *state = i2c_get_adapdata(i2c_adap);
-	struct i2c_msg m[1 + num];
+	struct i2c_msg m[3];
 	u8 tx_open[2] = { CON_1, state->CON_1_val | 1 }; /* repeater stops once there was a stop condition */
 
+	if (1 + num > ARRAY_SIZE(m)) {
+		printk(KERN_WARNING
+		       "%s: i2c xfer: num=%d is too big!\n",
+		       KBUILD_MODNAME, num);
+		return  -EOPNOTSUPP;
+	}
+
 	memset(m, 0, sizeof(struct i2c_msg) * (1 + num));
 
 	m[0].addr = state->config->demod_address;
@@ -847,7 +854,7 @@ static int s5h1420_tuner_i2c_tuner_xfer(
 
 	memcpy(&m[1], msg, sizeof(struct i2c_msg) * num);
 
-	return i2c_transfer(state->i2c, m, 1+num) == 1 + num ? num : -EIO;
+	return i2c_transfer(state->i2c, m, 1 + num) == 1 + num ? num : -EIO;
 }
 
 static struct i2c_algorithm s5h1420_tuner_i2c_algo = {
author maintainer
#160 lore raw

PATCH 158/173 X.509: Remove certificate date checks

In reply to Greg Kroah-Hartman

3.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: David Howells <[email protected]>

commit 124df926090b32a998483f6e43ebeccdbe5b5302 upstream.

Remove the certificate date checks that are performed when a certificate is parsed. There are two checks: a valid from and a valid to. The first check is causing a lot of problems with system clocks that don't keep good time and the second places an implicit expiry date upon the kernel when used for module signing, so do we really need them?

cc David Woodhouse <[email protected]>
cc Rusty Russell <[email protected]>
cc Josh Boyer <[email protected]>
cc Alexander Holler <[email protected]>
---
 crypto/asymmetric_keys/x509_public_key.c |   38 -------------------------------
 1 file changed, 38 deletions(-)
crypto/asymmetric_keys/x509_public_key.c +0 -38
@@ -106,7 +106,6 @@ error_no_sig:
 static int x509_key_preparse(struct key_preparsed_payload *prep)
 {
 	struct x509_certificate *cert;
-	struct tm now;
 	size_t srlen, sulen;
 	char *desc = NULL;
 	int ret;
@@ -137,43 +136,6 @@ static int x509_key_preparse(struct key_
 		goto error_free_cert;
 	}
 
-	time_to_tm(CURRENT_TIME.tv_sec, 0, &now);
-	pr_devel("Now: %04ld-%02d-%02d %02d:%02d:%02d\n",
-		 now.tm_year + 1900, now.tm_mon + 1, now.tm_mday,
-		 now.tm_hour, now.tm_min,  now.tm_sec);
-	if (now.tm_year < cert->valid_from.tm_year ||
-	    (now.tm_year == cert->valid_from.tm_year &&
-	     (now.tm_mon < cert->valid_from.tm_mon ||
-	      (now.tm_mon == cert->valid_from.tm_mon &&
-	       (now.tm_mday < cert->valid_from.tm_mday ||
-		(now.tm_mday == cert->valid_from.tm_mday &&
-		 (now.tm_hour < cert->valid_from.tm_hour ||
-		  (now.tm_hour == cert->valid_from.tm_hour &&
-		   (now.tm_min < cert->valid_from.tm_min ||
-		    (now.tm_min == cert->valid_from.tm_min &&
-		     (now.tm_sec < cert->valid_from.tm_sec
-		      ))))))))))) {
-		pr_warn("Cert %s is not yet valid\n", cert->fingerprint);
-		ret = -EKEYREJECTED;
-		goto error_free_cert;
-	}
-	if (now.tm_year > cert->valid_to.tm_year ||
-	    (now.tm_year == cert->valid_to.tm_year &&
-	     (now.tm_mon > cert->valid_to.tm_mon ||
-	      (now.tm_mon == cert->valid_to.tm_mon &&
-	       (now.tm_mday > cert->valid_to.tm_mday ||
-		(now.tm_mday == cert->valid_to.tm_mday &&
-		 (now.tm_hour > cert->valid_to.tm_hour ||
-		  (now.tm_hour == cert->valid_to.tm_hour &&
-		   (now.tm_min > cert->valid_to.tm_min ||
-		    (now.tm_min == cert->valid_to.tm_min &&
-		     (now.tm_sec > cert->valid_to.tm_sec
-		      ))))))))))) {
-		pr_warn("Cert %s has expired\n", cert->fingerprint);
-		ret = -EKEYEXPIRED;
-		goto error_free_cert;
-	}
-
 	cert->pub->algo = x509_public_key_algorithms[cert->pkey_algo];
 	cert->pub->id_type = PKEY_ID_X509;
 
author maintainer
#161 lore raw

PATCH 159/173 HID: roccat: add new device return value

In reply to Greg Kroah-Hartman

3.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Stefan Achatz <[email protected]>

commit 14fc4290df2fb94a28f39dab9ed32feaa5527bef upstream.

Ryos uses a new return value for critical errors, others have been confirmed.

---
 drivers/hid/hid-roccat-common.c |   12 ++++++------
 1 file changed, 6 insertions(+), 6 deletions(-)
drivers/hid/hid-roccat-common.c +6 -6
@@ -65,10 +65,11 @@ int roccat_common2_send(struct usb_devic
 EXPORT_SYMBOL_GPL(roccat_common2_send);
 
 enum roccat_common2_control_states {
-	ROCCAT_COMMON_CONTROL_STATUS_OVERLOAD = 0,
+	ROCCAT_COMMON_CONTROL_STATUS_CRITICAL = 0,
 	ROCCAT_COMMON_CONTROL_STATUS_OK = 1,
 	ROCCAT_COMMON_CONTROL_STATUS_INVALID = 2,
-	ROCCAT_COMMON_CONTROL_STATUS_WAIT = 3,
+	ROCCAT_COMMON_CONTROL_STATUS_BUSY = 3,
+	ROCCAT_COMMON_CONTROL_STATUS_CRITICAL_NEW = 4,
 };
 
 static int roccat_common2_receive_control_status(struct usb_device *usb_dev)
@@ -88,13 +89,12 @@ static int roccat_common2_receive_contro
 		switch (control.value) {
 		case ROCCAT_COMMON_CONTROL_STATUS_OK:
 			return 0;
-		case ROCCAT_COMMON_CONTROL_STATUS_WAIT:
+		case ROCCAT_COMMON_CONTROL_STATUS_BUSY:
 			msleep(500);
 			continue;
 		case ROCCAT_COMMON_CONTROL_STATUS_INVALID:
-
-		case ROCCAT_COMMON_CONTROL_STATUS_OVERLOAD:
-			/* seems to be critical - replug necessary */
+		case ROCCAT_COMMON_CONTROL_STATUS_CRITICAL:
+		case ROCCAT_COMMON_CONTROL_STATUS_CRITICAL_NEW:
 			return -EINVAL;
 		default:
 			dev_err(&usb_dev->dev,
author maintainer
#162 lore raw

PATCH 160/173 HID: roccat: fix Coverity CID 141438

In reply to Greg Kroah-Hartman

3.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Stefan Achatz <[email protected]>

commit 7be63f20b00840a6f1c718dcee00855688d64acd upstream.

Add missing switch breaks.

---
 drivers/hid/hid-roccat-kovaplus.c |    4 ++++
 1 file changed, 4 insertions(+)
drivers/hid/hid-roccat-kovaplus.c +4 -0
@@ -577,9 +577,13 @@ static void kovaplus_keep_values_up_to_d
 		break;
 	case KOVAPLUS_MOUSE_REPORT_BUTTON_TYPE_CPI:
 		kovaplus->actual_cpi = kovaplus_convert_event_cpi(button_report->data1);
+		break;
 	case KOVAPLUS_MOUSE_REPORT_BUTTON_TYPE_SENSITIVITY:
 		kovaplus->actual_x_sensitivity = button_report->data1;
 		kovaplus->actual_y_sensitivity = button_report->data2;
+		break;
+	default:
+		break;
 	}
 }
 
author maintainer
#163 lore raw

PATCH 161/173 HID: roccat: add missing special driver declarations

In reply to Greg Kroah-Hartman

3.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Stefan Achatz <[email protected]>

commit e078809df5611600965f4d3420c3256260fc3e3d upstream.

Forgot two special driver declarations and sorted the list.

---
 drivers/hid/hid-core.c |    4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)
drivers/hid/hid-core.c +3 -1
@@ -1751,12 +1751,14 @@ static const struct hid_device_id hid_ha
 	{ HID_USB_DEVICE(USB_VENDOR_ID_PETALYNX, USB_DEVICE_ID_PETALYNX_MAXTER_REMOTE) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_PRIMAX, USB_DEVICE_ID_PRIMAX_KEYBOARD) },
 #if IS_ENABLED(CONFIG_HID_ROCCAT)
-	{ HID_USB_DEVICE(USB_VENDOR_ID_ROCCAT, USB_DEVICE_ID_ROCCAT_KONE) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_ROCCAT, USB_DEVICE_ID_ROCCAT_ARVO) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_ROCCAT, USB_DEVICE_ID_ROCCAT_ISKU) },
+	{ HID_USB_DEVICE(USB_VENDOR_ID_ROCCAT, USB_DEVICE_ID_ROCCAT_ISKUFX) },
+	{ HID_USB_DEVICE(USB_VENDOR_ID_ROCCAT, USB_DEVICE_ID_ROCCAT_KONE) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_ROCCAT, USB_DEVICE_ID_ROCCAT_KONEPLUS) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_ROCCAT, USB_DEVICE_ID_ROCCAT_KONEPURE) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_ROCCAT, USB_DEVICE_ID_ROCCAT_KONEPURE_OPTICAL) },
+	{ HID_USB_DEVICE(USB_VENDOR_ID_ROCCAT, USB_DEVICE_ID_ROCCAT_KONEXTD) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_ROCCAT, USB_DEVICE_ID_ROCCAT_KOVAPLUS) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_ROCCAT, USB_DEVICE_ID_ROCCAT_LUA) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_ROCCAT, USB_DEVICE_ID_ROCCAT_PYRA_WIRED) },
author maintainer
#164 lore raw

PATCH 162/173 HID: enable Mayflash USB Gamecube Adapter

In reply to Greg Kroah-Hartman

3.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Tristan Rice <[email protected]>

commit e17f5d7667c5414b8f12a93ef14aae0824bd2beb upstream.

This is a patch that adds the new Mayflash Gamecube Controller to USB adapter (ID 1a34:f705 ACRUX) to the ACRUX driver (drivers/hid/hid-axff.c) with full force feedback support.

---
 drivers/hid/hid-axff.c |    3 ++-
 drivers/hid/hid-core.c |    1 +
 2 files changed, 3 insertions(+), 1 deletion(-)
drivers/hid/hid-axff.c +2 -1
@@ -95,7 +95,7 @@ static int axff_init(struct hid_device *
 		}
 	}
 
-	if (field_count < 4) {
+	if (field_count < 4 && hid->product != 0xf705) {
 		hid_err(hid, "not enough fields in the report: %d\n",
 			field_count);
 		return -ENODEV;
@@ -180,6 +180,7 @@ static void ax_remove(struct hid_device
 
 static const struct hid_device_id ax_devices[] = {
 	{ HID_USB_DEVICE(USB_VENDOR_ID_ACRUX, 0x0802), },
+	{ HID_USB_DEVICE(USB_VENDOR_ID_ACRUX, 0xf705), },
 	{ }
 };
 MODULE_DEVICE_TABLE(hid, ax_devices);
drivers/hid/hid-core.c +1 -0
@@ -1562,6 +1562,7 @@ static const struct hid_device_id hid_ha
 	{ HID_USB_DEVICE(USB_VENDOR_ID_A4TECH, USB_DEVICE_ID_A4TECH_X5_005D) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_A4TECH, USB_DEVICE_ID_A4TECH_RP_649) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_ACRUX, 0x0802) },
+	{ HID_USB_DEVICE(USB_VENDOR_ID_ACRUX, 0xf705) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_APPLE, USB_DEVICE_ID_APPLE_MIGHTYMOUSE) },
 	{ HID_BLUETOOTH_DEVICE(USB_VENDOR_ID_APPLE, USB_DEVICE_ID_APPLE_MAGICMOUSE) },
 	{ HID_BLUETOOTH_DEVICE(USB_VENDOR_ID_APPLE, USB_DEVICE_ID_APPLE_MAGICTRACKPAD) },
author maintainer
#165 lore raw

PATCH 163/173 HID: apple: option to swap the Option ("Alt") and Command ("Flag") keys.

In reply to Greg Kroah-Hartman

3.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Nanno Langstraat <[email protected]>

commit 43c831468b3d26dbe8f2e061ccaf1abaf9cc1b8b upstream.

Use case: people who use both Apple and PC keyboards regularly, and desire to keep&use their PC muscle memory.

A particular use case: an Apple compact external keyboard connected to a PC laptop. (This use case can't be covered well by X.org key remappings etc.)

---
 drivers/hid/hid-apple.c |   22 ++++++++++++++++++++++
 1 file changed, 22 insertions(+)
drivers/hid/hid-apple.c +22 -0
@@ -46,6 +46,12 @@ module_param(iso_layout, uint, 0644);
 MODULE_PARM_DESC(iso_layout, "Enable/Disable hardcoded ISO-layout of the keyboard. "
 		"(0 = disabled, [1] = enabled)");
 
+static unsigned int swap_opt_cmd = 0;
+module_param(swap_opt_cmd, uint, 0644);
+MODULE_PARM_DESC(swap_opt_cmd, "Swap the Option (\"Alt\") and Command (\"Flag\") keys. "
+		"(For people who want to keep Windows PC keyboard muscle memory. "
+		"[0] = as-is, Mac layout. 1 = swapped, Windows layout.)");
+
 struct apple_sc {
 	unsigned long quirks;
 	unsigned int fn_on;
@@ -150,6 +156,14 @@ static const struct apple_key_translatio
 	{ }
 };
 
+static const struct apple_key_translation swapped_option_cmd_keys[] = {
+	{ KEY_LEFTALT,	KEY_LEFTMETA },
+	{ KEY_LEFTMETA,	KEY_LEFTALT },
+	{ KEY_RIGHTALT,	KEY_RIGHTMETA },
+	{ KEY_RIGHTMETA,KEY_RIGHTALT },
+	{ }
+};
+
 static const struct apple_key_translation *apple_find_translation(
 		const struct apple_key_translation *table, u16 from)
 {
@@ -242,6 +256,14 @@ static int hidinput_apple_event(struct h
 		}
 	}
 
+	if (swap_opt_cmd) {
+		trans = apple_find_translation(swapped_option_cmd_keys, usage->code);
+		if (trans) {
+			input_event(input, usage->type, trans->to, value);
+			return 1;
+		}
+	}
+
 	return 0;
 }
 
author maintainer
#166 lore raw

PATCH 164/173 drm/radeon: use 64-bit math to calculate CTS values for audio (v2)

In reply to Greg Kroah-Hartman

3.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Alex Deucher <[email protected]>

commit 062c2e4363451d49ef840232fe65e8bff0dde2a5 upstream.

Avoid losing precision. See bug:
https://bugs.freedesktop.org/show_bug.cgi?id=69675

v2: fix math as per Anssi's comments.

---
 drivers/gpu/drm/radeon/r600_hdmi.c |   11 +++++++++--
 1 file changed, 9 insertions(+), 2 deletions(-)
drivers/gpu/drm/radeon/r600_hdmi.c +9 -2
@@ -75,8 +75,15 @@ static const struct radeon_hdmi_acr r600
  */
 static void r600_hdmi_calc_cts(uint32_t clock, int *CTS, int N, int freq)
 {
-	if (*CTS == 0)
-		*CTS = clock * N / (128 * freq) * 1000;
+	u64 n;
+	u32 d;
+
+	if (*CTS == 0) {
+		n = (u64)clock * (u64)N * 1000ULL;
+		d = 128 * freq;
+		do_div(n, d);
+		*CTS = n;
+	}
 	DRM_DEBUG("Using ACR timing N=%d CTS=%d for frequency %d\n",
 		  N, *CTS, freq);
 }
author maintainer
#167 lore raw

PATCH 165/173 drm/radeon: fix N/CTS clock matching for audio

In reply to Greg Kroah-Hartman

3.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Alex Deucher <[email protected]>

commit e7d12c2f98ae1e68c7298e5028048d150fa553a1 upstream.

The drm code that calculates the 1001 clocks rounds up rather than truncating. This allows the table to match properly on those modes.

See bug:
https://bugs.freedesktop.org/show_bug.cgi?id=69675

---
 drivers/gpu/drm/radeon/r600_hdmi.c |    6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)
drivers/gpu/drm/radeon/r600_hdmi.c +3 -3
@@ -57,15 +57,15 @@ enum r600_hdmi_iec_status_bits {
 static const struct radeon_hdmi_acr r600_hdmi_predefined_acr[] = {
     /*	     32kHz	  44.1kHz	48kHz    */
     /* Clock      N     CTS      N     CTS      N     CTS */
-    {  25174,  4576,  28125,  7007,  31250,  6864,  28125 }, /*  25,20/1.001 MHz */
+    {  25175,  4576,  28125,  7007,  31250,  6864,  28125 }, /*  25,20/1.001 MHz */
     {  25200,  4096,  25200,  6272,  28000,  6144,  25200 }, /*  25.20       MHz */
     {  27000,  4096,  27000,  6272,  30000,  6144,  27000 }, /*  27.00       MHz */
     {  27027,  4096,  27027,  6272,  30030,  6144,  27027 }, /*  27.00*1.001 MHz */
     {  54000,  4096,  54000,  6272,  60000,  6144,  54000 }, /*  54.00       MHz */
     {  54054,  4096,  54054,  6272,  60060,  6144,  54054 }, /*  54.00*1.001 MHz */
-    {  74175, 11648, 210937, 17836, 234375, 11648, 140625 }, /*  74.25/1.001 MHz */
+    {  74176, 11648, 210937, 17836, 234375, 11648, 140625 }, /*  74.25/1.001 MHz */
     {  74250,  4096,  74250,  6272,  82500,  6144,  74250 }, /*  74.25       MHz */
-    { 148351, 11648, 421875,  8918, 234375,  5824, 140625 }, /* 148.50/1.001 MHz */
+    { 148352, 11648, 421875,  8918, 234375,  5824, 140625 }, /* 148.50/1.001 MHz */
     { 148500,  4096, 148500,  6272, 165000,  6144, 148500 }, /* 148.50       MHz */
     {      0,  4096,      0,  6272,      0,  6144,      0 }  /* Other */
 };
author maintainer
#168 lore raw

PATCH 166/173 drm/radeon: use hw generated CTS/N values for audio

In reply to Greg Kroah-Hartman

3.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Alex Deucher <[email protected]>

commit ee0fec312a1c4e26f255955da942562cd8908a4b upstream.

Use the hw generated values rather than calculating them in the driver. There may be some older r6xx asics where this doesn't work correctly. This remains to be seen.

See bug:
https://bugs.freedesktop.org/show_bug.cgi?id=69675

---
 drivers/gpu/drm/radeon/evergreen_hdmi.c |    3 +--
 drivers/gpu/drm/radeon/r600_hdmi.c      |    3 +--
 2 files changed, 2 insertions(+), 4 deletions(-)
drivers/gpu/drm/radeon/evergreen_hdmi.c +1 -2
@@ -219,8 +219,7 @@ void evergreen_hdmi_setmode(struct drm_e
 	/* fglrx clears sth in AFMT_AUDIO_PACKET_CONTROL2 here */
 
 	WREG32(HDMI_ACR_PACKET_CONTROL + offset,
-	       HDMI_ACR_AUTO_SEND | /* allow hw to sent ACR packets when required */
-	       HDMI_ACR_SOURCE); /* select SW CTS value */
+	       HDMI_ACR_AUTO_SEND); /* allow hw to sent ACR packets when required */
 
 	evergreen_hdmi_update_ACR(encoder, mode->clock);
 
drivers/gpu/drm/radeon/r600_hdmi.c +1 -2
@@ -320,8 +320,7 @@ void r600_hdmi_setmode(struct drm_encode
 	}
 
 	WREG32(HDMI0_ACR_PACKET_CONTROL + offset,
-	       HDMI0_ACR_AUTO_SEND | /* allow hw to sent ACR packets when required */
-	       HDMI0_ACR_SOURCE); /* select SW CTS value */
+	       HDMI0_ACR_AUTO_SEND); /* allow hw to sent ACR packets when required */
 
 	WREG32(HDMI0_VBI_PACKET_CONTROL + offset,
 	       HDMI0_NULL_SEND | /* send null packets when required */
author maintainer
#169 lore raw

PATCH 167/173 drm/radeon: re-enable sw ACR support on pre-DCE4

In reply to Greg Kroah-Hartman

3.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Alex Deucher <[email protected]>

commit b852c985010a77c850b7548d64bbb964ca462b02 upstream.

HW ACR support may have issues on some older chips, so use SW ACR for now until we've tested further.

---
 drivers/gpu/drm/radeon/r600_hdmi.c |    1 +
 1 file changed, 1 insertion(+)
drivers/gpu/drm/radeon/r600_hdmi.c +1 -0
@@ -320,6 +320,7 @@ void r600_hdmi_setmode(struct drm_encode
 	}
 
 	WREG32(HDMI0_ACR_PACKET_CONTROL + offset,
+	       HDMI0_ACR_SOURCE | /* select SW CTS value - XXX verify that hw CTS works on all families */
 	       HDMI0_ACR_AUTO_SEND); /* allow hw to sent ACR packets when required */
 
 	WREG32(HDMI0_VBI_PACKET_CONTROL + offset,
author maintainer
#170 lore raw

PATCH 168/173 iwlwifi: dont WARN on host commands sent when firmware is dead

In reply to Greg Kroah-Hartman

3.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Emmanuel Grumbach <[email protected]>

commit 8ca95995e64f5d270889badb3e449dca91106a2b upstream.

This triggers automatic bug reports and add no valuable information. Print a simple error instead and drop the host command.

---
 drivers/net/wireless/iwlwifi/iwl-trans.h |    6 ++++--
 1 file changed, 4 insertions(+), 2 deletions(-)
drivers/net/wireless/iwlwifi/iwl-trans.h +4 -2
@@ -605,8 +605,10 @@ static inline int iwl_trans_send_cmd(str
 {
 	int ret;
 
-	WARN_ONCE(trans->state != IWL_TRANS_FW_ALIVE,
-		  "%s bad state = %d", __func__, trans->state);
+	if (trans->state != IWL_TRANS_FW_ALIVE) {
+		IWL_ERR(trans, "%s bad state = %d", __func__, trans->state);
+		return -EIO;
+	}
 
 	if (!(cmd->flags & CMD_ASYNC))
 		lock_map_acquire_read(&trans->sync_cmd_lockdep_map);
author maintainer
#171 lore raw

PATCH 169/173 netfilter: nf_conntrack: use RCU safe kfree for conntrack extensions

In reply to Greg Kroah-Hartman

3.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Michal Kubecek <[email protected]>

commit c13a84a830a208fb3443628773c8ca0557773cc7 upstream.

Commit 68b80f11 (netfilter: nf_nat: fix RCU races) introduced RCU protection for freeing extension data when reallocation moves them to a new location. We need the same protection when freeing them in nf_ct_ext_free() in order to prevent a use-after-free by other threads referencing a NAT extension data via bysource list.

---
 include/net/netfilter/nf_conntrack_extend.h |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
include/net/netfilter/nf_conntrack_extend.h +1 -1
@@ -80,7 +80,7 @@ static inline void nf_ct_ext_destroy(str
 static inline void nf_ct_ext_free(struct nf_conn *ct)
 {
 	if (ct->ext)
-		kfree(ct->ext);
+		kfree_rcu(ct->ext, rcu);
 }
 
 /* Add this type, returns pointer to data or NULL. */
author maintainer
#172 lore raw

PATCH 170/173 media: cx23885: Fix TeVii S471 regression since introduction of ts2020

In reply to Greg Kroah-Hartman

3.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Johannes Koch <[email protected]>

commit b43ea8068d2090cb1e44632c8a938ab40d2c7419 upstream.

Patch to make TeVii S471 cards use the ts2020 tuner, since ds3000 driver no longer contains tuning code.

---
 drivers/media/pci/cx23885/cx23885-dvb.c |    4 ++++
 1 file changed, 4 insertions(+)
drivers/media/pci/cx23885/cx23885-dvb.c +4 -0
@@ -1249,6 +1249,10 @@ static int dvb_register(struct cx23885_t
 		fe0->dvb.frontend = dvb_attach(ds3000_attach,
 					&tevii_ds3000_config,
 					&i2c_bus->i2c_adap);
+		if (fe0->dvb.frontend != NULL) {
+			dvb_attach(ts2020_attach, fe0->dvb.frontend,
+				&tevii_ts2020_config, &i2c_bus->i2c_adap);
+		}
 		break;
 	case CX23885_BOARD_PROF_8000:
 		i2c_bus = &dev->i2c_bus[0];
author maintainer
#173 lore raw

PATCH 171/173 iwl3945: better skb management in rx path

In reply to Greg Kroah-Hartman

3.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Eric Dumazet <[email protected]>

commit 45fe142cefa864b685615bcb930159f6749c3667 upstream.

Steinar reported reallocations of skb->head with IPv6, leading to a warning in skb_try_coalesce()

It turns out iwl3945 has several problems :

1) skb->truesize is underestimated.
We really consume PAGE_SIZE bytes for a fragment,
not the frame length.
2) 128 bytes of initial headroom is a bit low and forces reallocations.
3) We can avoid consuming a full page for small enough frames.

---
 drivers/net/wireless/iwlegacy/3945.c |   31 +++++++++++++++++++------------
 1 file changed, 19 insertions(+), 12 deletions(-)
drivers/net/wireless/iwlegacy/3945.c +19 -12
@@ -462,6 +462,8 @@ il3945_is_network_packet(struct il_priv
 	}
 }
 
+#define SMALL_PACKET_SIZE 256
+
 static void
 il3945_pass_packet_to_mac80211(struct il_priv *il, struct il_rx_buf *rxb,
 			       struct ieee80211_rx_status *stats)
@@ -470,14 +472,13 @@ il3945_pass_packet_to_mac80211(struct il
 	struct ieee80211_hdr *hdr = (struct ieee80211_hdr *)IL_RX_DATA(pkt);
 	struct il3945_rx_frame_hdr *rx_hdr = IL_RX_HDR(pkt);
 	struct il3945_rx_frame_end *rx_end = IL_RX_END(pkt);
-	u16 len = le16_to_cpu(rx_hdr->len);
+	u32 len = le16_to_cpu(rx_hdr->len);
 	struct sk_buff *skb;
 	__le16 fc = hdr->frame_control;
+	u32 fraglen = PAGE_SIZE << il->hw_params.rx_page_order;
 
 	/* We received data from the HW, so stop the watchdog */
-	if (unlikely
-	    (len + IL39_RX_FRAME_SIZE >
-	     PAGE_SIZE << il->hw_params.rx_page_order)) {
+	if (unlikely(len + IL39_RX_FRAME_SIZE > fraglen)) {
 		D_DROP("Corruption detected!\n");
 		return;
 	}
@@ -488,26 +489,32 @@ il3945_pass_packet_to_mac80211(struct il
 		return;
 	}
 
-	skb = dev_alloc_skb(128);
+	skb = dev_alloc_skb(SMALL_PACKET_SIZE);
 	if (!skb) {
 		IL_ERR("dev_alloc_skb failed\n");
 		return;
 	}
 
 	if (!il3945_mod_params.sw_crypto)
-		il_set_decrypted_flag(il, (struct ieee80211_hdr *)rxb_addr(rxb),
+		il_set_decrypted_flag(il, (struct ieee80211_hdr *)pkt,
 				      le32_to_cpu(rx_end->status), stats);
 
-	skb_add_rx_frag(skb, 0, rxb->page,
-			(void *)rx_hdr->payload - (void *)pkt, len,
-			len);
-
+	/* If frame is small enough to fit into skb->head, copy it
+	 * and do not consume a full page
+	 */
+	if (len <= SMALL_PACKET_SIZE) {
+		memcpy(skb_put(skb, len), rx_hdr->payload, len);
+	} else {
+		skb_add_rx_frag(skb, 0, rxb->page,
+				(void *)rx_hdr->payload - (void *)pkt, len,
+				fraglen);
+		il->alloc_rxb_page--;
+		rxb->page = NULL;
+	}
 	il_update_stats(il, false, fc, len);
 	memcpy(IEEE80211_SKB_RXCB(skb), stats, sizeof(*stats));
 
 	ieee80211_rx(il->hw, skb);
-	il->alloc_rxb_page--;
-	rxb->page = NULL;
 }
 
 #define IL_DELAY_NEXT_SCAN_AFTER_ASSOC (HZ*6)
author maintainer
#174 lore raw

PATCH 172/173 iwl4965: better skb management in rx path

In reply to Greg Kroah-Hartman

3.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Stanislaw Gruszka <[email protected]>

commit c1de4a9557d9e25e41fc4ba034b9659152205539 upstream.

4965 version of Eric patch "iwl3945: better skb management in rx path". It fixes several problems :

1) skb->truesize is underestimated.
We really consume PAGE_SIZE bytes for a fragment,
not the frame length.
2) 128 bytes of initial headroom is a bit low and forces reallocations.
3) We can avoid consuming a full page for small enough frames.

---
 drivers/net/wireless/iwlegacy/4965-mac.c |   18 ++++++++++++------
 1 file changed, 12 insertions(+), 6 deletions(-)
drivers/net/wireless/iwlegacy/4965-mac.c +12 -6
@@ -574,9 +574,11 @@ il4965_translate_rx_status(struct il_pri
 	return decrypt_out;
 }
 
+#define SMALL_PACKET_SIZE 256
+
 static void
 il4965_pass_packet_to_mac80211(struct il_priv *il, struct ieee80211_hdr *hdr,
-			       u16 len, u32 ampdu_status, struct il_rx_buf *rxb,
+			       u32 len, u32 ampdu_status, struct il_rx_buf *rxb,
 			       struct ieee80211_rx_status *stats)
 {
 	struct sk_buff *skb;
@@ -593,21 +595,25 @@ il4965_pass_packet_to_mac80211(struct il
 	    il_set_decrypted_flag(il, hdr, ampdu_status, stats))
 		return;
 
-	skb = dev_alloc_skb(128);
+	skb = dev_alloc_skb(SMALL_PACKET_SIZE);
 	if (!skb) {
 		IL_ERR("dev_alloc_skb failed\n");
 		return;
 	}
 
-	skb_add_rx_frag(skb, 0, rxb->page, (void *)hdr - rxb_addr(rxb), len,
-			len);
+	if (len <= SMALL_PACKET_SIZE) {
+		memcpy(skb_put(skb, len), hdr, len);
+	} else {
+		skb_add_rx_frag(skb, 0, rxb->page, (void *)hdr - rxb_addr(rxb),
+				len, PAGE_SIZE << il->hw_params.rx_page_order);
+		il->alloc_rxb_page--;
+		rxb->page = NULL;
+	}
 
 	il_update_stats(il, false, fc, len);
 	memcpy(IEEE80211_SKB_RXCB(skb), stats, sizeof(*stats));
 
 	ieee80211_rx(il->hw, skb);
-	il->alloc_rxb_page--;
-	rxb->page = NULL;
 }
 
 /* Called for N_RX (legacy ABG frames), or
author maintainer
#175 lore raw

PATCH 173/173 xen-netback: fix refcnt unbalance for 3.10

In reply to Greg Kroah-Hartman

3.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Wei Liu <[email protected]>

With the introduction of "xen-netback: Don't destroy the netdev until the vif is shut down" (upstream commit id 279f438e36), vif disconnect and free are separated. However in the backported version reference counting code was not correctly modified, and the reset of vif->irq was lost. If frontend goes through vif life cycle more than once the reference counting is skewed.

This patch adds back the missing vif->irq reset line. It also moves several lines of the reference counting code to vif_free, so the moved code corresponds to the counterpart in vif_alloc, thus the reference counting is balanced.

---
 drivers/net/xen-netback/interface.c |   10 ++++++----
 1 file changed, 6 insertions(+), 4 deletions(-)
drivers/net/xen-netback/interface.c +6 -4
@@ -365,17 +365,19 @@ void xenvif_disconnect(struct xenvif *vi
 	if (netif_carrier_ok(vif->dev))
 		xenvif_carrier_off(vif);
 
-	atomic_dec(&vif->refcnt);
-	wait_event(vif->waiting_to_free, atomic_read(&vif->refcnt) == 0);
-
-	if (vif->irq)
+	if (vif->irq) {
 		unbind_from_irqhandler(vif->irq, vif);
+		vif->irq = 0;
+	}
 
 	xen_netbk_unmap_frontend_rings(vif);
 }
 
 void xenvif_free(struct xenvif *vif)
 {
+	atomic_dec(&vif->refcnt);
+	wait_event(vif->waiting_to_free, atomic_read(&vif->refcnt) == 0);
+
 	unregister_netdev(vif->dev);
 
 	free_netdev(vif->dev);
#176 lore raw
In reply to Greg Kroah-Hartman
Quoted 8 lines · Greg Kroah-Hartman

This is the start of the stable review cycle for the 3.10.22 release. There are 173 patches in this series, all will be posted as a response to this one. If anyone has any issues with these being applied, please let me know.

Responses should be made by Wed Dec 4 19:10:16 UTC 2013. Anything received after that time might be too late.

Build results:

	total: 110 pass: 109 skipped: 0 fail: 1

qemu tests all passed.

The build failure is new. avr32:atngw100mkii_evklcd101_defconfig fails to build with

lib/lib.a(vsprintf.o): In function `pointer':
vsprintf.c:(.text+0x17dc): relocation truncated to fit: R_AVR32_16N_PCREL against symbol `_ctype' defined in .text section in lib/lib.a(ctype.o)
make: *** [vmlinux] Error 1

Guenter

author maintainer
#177 lore raw
Quoted 12 lines · Guenter Roeck
Quoted 8 lines · Greg Kroah-Hartman

This is the start of the stable review cycle for the 3.10.22 release. There are 173 patches in this series, all will be posted as a response to this one. If anyone has any issues with these being applied, please let me know.

Responses should be made by Wed Dec 4 19:10:16 UTC 2013. Anything received after that time might be too late.

Build results:

	total: 110 pass: 109 skipped: 0 fail: 1
Quoted 8 lines

qemu tests all passed.

The build failure is new. avr32:atngw100mkii_evklcd101_defconfig fails to build with

lib/lib.a(vsprintf.o): In function `pointer':
vsprintf.c:(.text+0x17dc): relocation truncated to fit: R_AVR32_16N_PCREL against symbol `_ctype' defined in .text section in lib/lib.a(ctype.o)
make: *** [vmlinux] Error 1

Thanks, hopefully one of the avr32 people can look into this...

greg k-h

#178 lore raw
In reply to Greg Kroah-Hartman
Quoted 8 lines · Greg Kroah-Hartman

This is the start of the stable review cycle for the 3.10.22 release. There are 173 patches in this series, all will be posted as a response to this one. If anyone has any issues with these being applied, please let me know.

Responses should be made by Wed Dec 4 19:10:16 UTC 2013. Anything received after that time might be too late.

Quoted 8 lines

The whole patch series can be found in one patch at:

	kernel.org/pub/linux/kernel/v3.0/stable-review/patch-3.10.22-rc1.gz

and the diffstat can be found below.

thanks,

greg k-h

Patch applied cleanly
compile and boot tests - passed
dmesg regression testing - passed

dmesgs look good. No regressions compared to the previous dmesgs for this release. dmesg emerg, crit, alert, err are clean. No regressions in warn.

Test systems

Samsung Series 9 900X4C Intel Corei5 (3.4 and later) HP ProBook 6475b AMD A10-4600M APU with Radeon(tm) HD Graphics Dell OptiPlex 790 Intel(R) Core(TM) i5-2400

-- Shuah

Signature · 4 lines
Shuah Khan
Senior Linux Kernel Developer - Open Source Group
Samsung Research America(Silicon Valley)
[email protected] | (970) 672-0658
#179 lore raw
In reply to Greg Kroah-Hartman

At Mon, 2 Dec 2013 11:09:43 -0800,

Quoted 8 lines · Greg Kroah-Hartman

This is the start of the stable review cycle for the 3.10.22 release. There are 173 patches in this series, all will be posted as a response to this one. If anyone has any issues with these being applied, please let me know.

Responses should be made by Wed Dec 4 19:10:16 UTC 2013. Anything received after that time might be too late.

This kernel can be built and boot without any problem. Building a kernel with this kernel also works fine.

- Build Machine: debian jessy x86_64
CPU: Intel(R) Core(TM) i5-2400 CPU @ 3.10GHz x 4
memory: 8GB

- Test machine: debian jessy x86_64(KVM guest on the Build Machine)
vCPU: x2
memory: 2GB

Thanks,
Satoru