Skip to contentSkip to conversation

remotely powering on a OMAP5 uEVM over the debug port

HACK Olof Johansson 2 participants 2 messages Dec 5, 2013

lore
Share & tools
lore
#0 lore raw

Here's a tiny hack I came up with to remote-power on an OMAP5 uEVM. I have mine in an unattended setup where I can cycle power, but it still needs a power button press to start.

Luckily two GPIO lines on the secondary FTDI channel are routed to the same buttons, so it can be done via software. It requires your board to have U37 populated though, so make sure you have it (mine did already).

The below little hack uses libmpsse, available at
https://code.google.com/p/libmpsse/.

To use it, give it the path of the FTDI device. I.e. on my system the uEVM is at 3-1.3.3. Check dmesg and lsusb (it's bus number + path).

Anyway, I figured this could be useful for others as well, so I'm posting just for that purpose. No warranties, don't come to me if you break your board with this, etc, etc.

This pulses the power button for 1 second (GPIOH5). If you want to pulse the reset instead, use GPIOH6.

#include <stdlib.h>
#include <stdio.h>
#include <unistd.h>
#include <usb.h>
#include <mpsse.h>

void usage(char *p)

{
	printf("Usage: %s <busnr>-<devpath>\n", p);
}

void fill_busdev(char *usbpath, int *bus, int *dev)

{
	char udir[PATH_MAX+1];
	FILE *fp;

	sprintf(udir, "/sys/bus/usb/devices/%s/busnum", usbpath);
	
	fp = fopen(udir, "r");
	if (!fp) {
		printf("can't open %s to find usb info\n", udir);
		exit(1);
	}
	fscanf(fp, "%d", bus);
	fclose(fp);

	sprintf(udir, "/sys/bus/usb/devices/%s/devnum", usbpath);
	
	fp = fopen(udir, "r");
	if (!fp) {
		printf("can't open %s to find usb info\n", udir);
		exit(1);
	}
	fscanf(fp, "%d", dev);
	fclose(fp);

}
int main(int argc, char **argv)

{
	struct mpsse_context *io = NULL;
	int i = 0;
	int bus, dev;

	if (argc < 1) {
		usage(argv[0]);
		exit(1);
	}

	fill_busdev(argv[1], &bus, &dev);

	while (1) {
		struct usb_device *ud;
		io = OpenIndex(0x0403, 0x6010, GPIO, 0, 0, 2, NULL, NULL, i++);
		if (!io || !io->open) {
			printf("Failed to open device %s\n", argv[1]);
			exit(1);
		}
		ud = usb_device(io->ftdi.usb_dev);
		if (ud->devnum == dev && ud->bus->location == bus) {
			printf("found: %s/%s %d\n", ud->bus->dirname, ud->filename, ud->bus->location);
			break;
		} else {
			printf("skipped: %s/%s %d\n", ud->bus->dirname, ud->filename, ud->bus->location);
		}
		Close(io);
	}

	/* Default is high */
	PinHigh(io, GPIOH5);
	PinHigh(io, GPIOH6);

	sleep(1);
	/* Pulse power */
	PinLow(io, GPIOH5);
	sleep(1);
	PinHigh(io, GPIOH5);

	Close(io);

	exit(0);
}
#1 lore raw
Quoted 3 lines · Olof Johansson

Here's a tiny hack I came up with to remote-power on an OMAP5 uEVM. I have mine in an unattended setup where I can cycle power, but it still needs a power button press to start.

Great, thanks a lot, just what I need :)

Regards,

Tony