Skip to contentSkip to conversation

ARM: sunxi: Fix interrupt trigger types in the DT

PATCH New Maxime Ripard 3 participants 8 messages Dec 7, 2013 – Dec 10, 2013

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

cover ARM: sunxi: Fix interrupt trigger types in the DT

Hi Kevin, Olof,

It would be great if you could merge these two patches by the end of the 3.13 release cycle.

Thanks!
Maxime

Maxime Ripard (2):
ARM: sun7i: dt: Fix interrupt trigger types
ARM: sun6i: dt: Fix interrupt trigger types

 arch/arm/boot/dts/sun6i-a31.dtsi | 27 ++++++++++++++------------
 arch/arm/boot/dts/sun7i-a20.dtsi | 42 ++++++++++++++++++++--------------------
 2 files changed, 36 insertions(+), 33 deletions(-)
Signature · 1 line
1.8.4.2
#1 lore raw

PATCH 1/2 ARM: sun7i: dt: Fix interrupt trigger types

The Allwinner A20 uses the ARM GIC as its internal interrupts controller. The GIC can work on several interrupt triggers, and the A20 was actually setting it up to use a rising edge as a trigger, while it was actually a level high trigger, leading to some interrupts that would be completely ignored if the edge was missed.

---
 arch/arm/boot/dts/sun7i-a20.dtsi | 42 ++++++++++++++++++++--------------------
 1 file changed, 21 insertions(+), 21 deletions(-)
arch/arm/boot/dts/sun7i-a20.dtsi +21 -21
index e46cfed..367611a 100644
@@ -170,7 +170,7 @@
 		emac: ethernet at 01c0b000 {
 			compatible = "allwinner,sun4i-emac";
 			reg = <0x01c0b000 0x1000>;
-			interrupts = <0 55 1>;
+			interrupts = <0 55 4>;
 			clocks = <&ahb_gates 17>;
 			status = "disabled";
 		};
@@ -186,7 +186,7 @@
 		pio: pinctrl at 01c20800 {
 			compatible = "allwinner,sun7i-a20-pinctrl";
 			reg = <0x01c20800 0x400>;
-			interrupts = <0 28 1>;
+			interrupts = <0 28 4>;
 			clocks = <&apb0_gates 5>;
 			gpio-controller;
 			interrupt-controller;
@@ -251,12 +251,12 @@
 		timer at 01c20c00 {
 			compatible = "allwinner,sun4i-timer";
 			reg = <0x01c20c00 0x90>;
-			interrupts = <0 22 1>,
-				     <0 23 1>,
-				     <0 24 1>,
-				     <0 25 1>,
-				     <0 67 1>,
-				     <0 68 1>;
+			interrupts = <0 22 4>,
+				     <0 23 4>,
+				     <0 24 4>,
+				     <0 25 4>,
+				     <0 67 4>,
+				     <0 68 4>;
 			clocks = <&osc24M>;
 		};
 
@@ -273,7 +273,7 @@
 		uart0: serial at 01c28000 {
 			compatible = "snps,dw-apb-uart";
 			reg = <0x01c28000 0x400>;
-			interrupts = <0 1 1>;
+			interrupts = <0 1 4>;
 			reg-shift = <2>;
 			reg-io-width = <4>;
 			clocks = <&apb1_gates 16>;
@@ -283,7 +283,7 @@
 		uart1: serial at 01c28400 {
 			compatible = "snps,dw-apb-uart";
 			reg = <0x01c28400 0x400>;
-			interrupts = <0 2 1>;
+			interrupts = <0 2 4>;
 			reg-shift = <2>;
 			reg-io-width = <4>;
 			clocks = <&apb1_gates 17>;
@@ -293,7 +293,7 @@
 		uart2: serial at 01c28800 {
 			compatible = "snps,dw-apb-uart";
 			reg = <0x01c28800 0x400>;
-			interrupts = <0 3 1>;
+			interrupts = <0 3 4>;
 			reg-shift = <2>;
 			reg-io-width = <4>;
 			clocks = <&apb1_gates 18>;
@@ -303,7 +303,7 @@
 		uart3: serial at 01c28c00 {
 			compatible = "snps,dw-apb-uart";
 			reg = <0x01c28c00 0x400>;
-			interrupts = <0 4 1>;
+			interrupts = <0 4 4>;
 			reg-shift = <2>;
 			reg-io-width = <4>;
 			clocks = <&apb1_gates 19>;
@@ -313,7 +313,7 @@
 		uart4: serial at 01c29000 {
 			compatible = "snps,dw-apb-uart";
 			reg = <0x01c29000 0x400>;
-			interrupts = <0 17 1>;
+			interrupts = <0 17 4>;
 			reg-shift = <2>;
 			reg-io-width = <4>;
 			clocks = <&apb1_gates 20>;
@@ -323,7 +323,7 @@
 		uart5: serial at 01c29400 {
 			compatible = "snps,dw-apb-uart";
 			reg = <0x01c29400 0x400>;
-			interrupts = <0 18 1>;
+			interrupts = <0 18 4>;
 			reg-shift = <2>;
 			reg-io-width = <4>;
 			clocks = <&apb1_gates 21>;
@@ -333,7 +333,7 @@
 		uart6: serial at 01c29800 {
 			compatible = "snps,dw-apb-uart";
 			reg = <0x01c29800 0x400>;
-			interrupts = <0 19 1>;
+			interrupts = <0 19 4>;
 			reg-shift = <2>;
 			reg-io-width = <4>;
 			clocks = <&apb1_gates 22>;
@@ -343,7 +343,7 @@
 		uart7: serial at 01c29c00 {
 			compatible = "snps,dw-apb-uart";
 			reg = <0x01c29c00 0x400>;
-			interrupts = <0 20 1>;
+			interrupts = <0 20 4>;
 			reg-shift = <2>;
 			reg-io-width = <4>;
 			clocks = <&apb1_gates 23>;
@@ -353,7 +353,7 @@
 		i2c0: i2c at 01c2ac00 {
 			compatible = "allwinner,sun4i-i2c";
 			reg = <0x01c2ac00 0x400>;
-			interrupts = <0 7 1>;
+			interrupts = <0 7 4>;
 			clocks = <&apb1_gates 0>;
 			clock-frequency = <100000>;
 			status = "disabled";
@@ -362,7 +362,7 @@
 		i2c1: i2c at 01c2b000 {
 			compatible = "allwinner,sun4i-i2c";
 			reg = <0x01c2b000 0x400>;
-			interrupts = <0 8 1>;
+			interrupts = <0 8 4>;
 			clocks = <&apb1_gates 1>;
 			clock-frequency = <100000>;
 			status = "disabled";
@@ -371,7 +371,7 @@
 		i2c2: i2c at 01c2b400 {
 			compatible = "allwinner,sun4i-i2c";
 			reg = <0x01c2b400 0x400>;
-			interrupts = <0 9 1>;
+			interrupts = <0 9 4>;
 			clocks = <&apb1_gates 2>;
 			clock-frequency = <100000>;
 			status = "disabled";
@@ -380,7 +380,7 @@
 		i2c3: i2c at 01c2b800 {
 			compatible = "allwinner,sun4i-i2c";
 			reg = <0x01c2b800 0x400>;
-			interrupts = <0 88 1>;
+			interrupts = <0 88 4>;
 			clocks = <&apb1_gates 3>;
 			clock-frequency = <100000>;
 			status = "disabled";
@@ -389,7 +389,7 @@
 		i2c4: i2c at 01c2bc00 {
 			compatible = "allwinner,sun4i-i2c";
 			reg = <0x01c2bc00 0x400>;
-			interrupts = <0 89 1>;
+			interrupts = <0 89 4>;
 			clocks = <&apb1_gates 15>;
 			clock-frequency = <100000>;
 			status = "disabled";
Signature · 1 line
1.8.4.2
#2 lore raw

PATCH 2/2 ARM: sun6i: dt: Fix interrupt trigger types

In reply to Maxime Ripard

The Allwinner A31 uses the ARM GIC as its internal interrupts controller. The GIC can work on several interrupt triggers, and the A31 was actually setting it up to use a rising edge as a trigger, while it was actually a level high trigger, leading to some interrupts that would be completely ignored if the edge was missed.

---
 arch/arm/boot/dts/sun6i-a31.dtsi | 27 +++++++++++++++------------
 1 file changed, 15 insertions(+), 12 deletions(-)
arch/arm/boot/dts/sun6i-a31.dtsi +15 -12
index c1751a6..7f5878c 100644
@@ -193,7 +193,10 @@
 		pio: pinctrl at 01c20800 {
 			compatible = "allwinner,sun6i-a31-pinctrl";
 			reg = <0x01c20800 0x400>;
-			interrupts = <0 11 1>, <0 15 1>, <0 16 1>, <0 17 1>;
+			interrupts = <0 11 4>,
+				     <0 15 4>,
+				     <0 16 4>,
+				     <0 17 4>;
 			clocks = <&apb1_gates 5>;
 			gpio-controller;
 			interrupt-controller;
@@ -212,11 +215,11 @@
 		timer at 01c20c00 {
 			compatible = "allwinner,sun4i-timer";
 			reg = <0x01c20c00 0xa0>;
-			interrupts = <0 18 1>,
-				     <0 19 1>,
-				     <0 20 1>,
-				     <0 21 1>,
-				     <0 22 1>;
+			interrupts = <0 18 4>,
+				     <0 19 4>,
+				     <0 20 4>,
+				     <0 21 4>,
+				     <0 22 4>;
 			clocks = <&osc24M>;
 		};
 
@@ -228,7 +231,7 @@
 		uart0: serial at 01c28000 {
 			compatible = "snps,dw-apb-uart";
 			reg = <0x01c28000 0x400>;
-			interrupts = <0 0 1>;
+			interrupts = <0 0 4>;
 			reg-shift = <2>;
 			reg-io-width = <4>;
 			clocks = <&apb2_gates 16>;
@@ -238,7 +241,7 @@
 		uart1: serial at 01c28400 {
 			compatible = "snps,dw-apb-uart";
 			reg = <0x01c28400 0x400>;
-			interrupts = <0 1 1>;
+			interrupts = <0 1 4>;
 			reg-shift = <2>;
 			reg-io-width = <4>;
 			clocks = <&apb2_gates 17>;
@@ -248,7 +251,7 @@
 		uart2: serial at 01c28800 {
 			compatible = "snps,dw-apb-uart";
 			reg = <0x01c28800 0x400>;
-			interrupts = <0 2 1>;
+			interrupts = <0 2 4>;
 			reg-shift = <2>;
 			reg-io-width = <4>;
 			clocks = <&apb2_gates 18>;
@@ -258,7 +261,7 @@
 		uart3: serial at 01c28c00 {
 			compatible = "snps,dw-apb-uart";
 			reg = <0x01c28c00 0x400>;
-			interrupts = <0 3 1>;
+			interrupts = <0 3 4>;
 			reg-shift = <2>;
 			reg-io-width = <4>;
 			clocks = <&apb2_gates 19>;
@@ -268,7 +271,7 @@
 		uart4: serial at 01c29000 {
 			compatible = "snps,dw-apb-uart";
 			reg = <0x01c29000 0x400>;
-			interrupts = <0 4 1>;
+			interrupts = <0 4 4>;
 			reg-shift = <2>;
 			reg-io-width = <4>;
 			clocks = <&apb2_gates 20>;
@@ -278,7 +281,7 @@
 		uart5: serial at 01c29400 {
 			compatible = "snps,dw-apb-uart";
 			reg = <0x01c29400 0x400>;
-			interrupts = <0 5 1>;
+			interrupts = <0 5 4>;
 			reg-shift = <2>;
 			reg-io-width = <4>;
 			clocks = <&apb2_gates 21>;
Signature · 1 line
1.8.4.2
#3 lore raw

cover ARM: sunxi: Fix interrupt trigger types in the DT

In reply to Maxime Ripard
Quoted 2 lines · Maxime Ripard

It would be great if you could merge these two patches by the end of the 3.13 release cycle.

I guess they should be marked for 'stable' backports as well, right?

Arnd

#4 lore raw

cover ARM: sunxi: Fix interrupt trigger types in the DT

Hi Arnd,

Quoted 5 lines · Arnd Bergmann
Quoted 2 lines · Maxime Ripard

It would be great if you could merge these two patches by the end of the 3.13 release cycle.

I guess they should be marked for 'stable' backports as well, right?

Aah, right.

I'll resend those patches Cc'ing stable.

Thanks,
Maxime

Signature · 10 lines
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 836 bytes
Desc: Digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20131210/b44696dc/attachment.sig>
#5 lore raw

cover ARM: sunxi: Fix interrupt trigger types in the DT

Quoted 10 lines · Maxime Ripard
Quoted 5 lines · Arnd Bergmann
Quoted 2 lines · Maxime Ripard

It would be great if you could merge these two patches by the end of the 3.13 release cycle.

I guess they should be marked for 'stable' backports as well, right?

Aah, right.

I'll resend those patches Cc'ing stable.

Ok, just to clarify: there is actually no need to Cc stable in the submission, we just need to make sure the Cc: stable is in the changeset description as it gets merged.

Arnd

#6 lore raw

cover ARM: sunxi: Fix interrupt trigger types in the DT

Quoted 8 lines · Arnd Bergmann
Quoted 7 lines · Maxime Ripard
Quoted 5 lines · Arnd Bergmann
Quoted 2 lines · Maxime Ripard

It would be great if you could merge these two patches by the end of the 3.13 release cycle.

I guess they should be marked for 'stable' backports as well, right?

Quoted 7 lines
Quoted 3 lines

Aah, right.

I'll resend those patches Cc'ing stable.

Ok, just to clarify: there is actually no need to Cc stable in the submission, we just need to make sure the Cc: stable is in the changeset description as it gets merged.

Hmmm, I guess I saw your mail a bit too late... :)

Maxime

Signature · 10 lines
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 836 bytes
Desc: Digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20131210/aded160f/attachment.sig>
#7 lore raw

cover ARM: sunxi: Fix interrupt trigger types in the DT

In reply to Maxime Ripard

Hi,

Quoted 7 lines · Maxime Ripard

Hi Kevin, Olof,

It would be great if you could merge these two patches by the end of the 3.13 release cycle.

Thanks!
Maxime

I see you've beat me to writing patches for this :) Looks good, the entire series is:

Regards,

Hans