gpio: twl4030: fix regression for twl gpio outputs for led pins
PATCH 1/1 gpio: twl4030: fix regression for twl gpio outputs for led pins
Commit 0b2aa8b (gpio: twl4030: Fix regression for twl gpio output) introduces yet another regression by ignoring the fact that we use twl gpio even for LED. For example, leda (offset 18) is used for USB port2 power on beagleboard-xm.
The original logic was supposed to setup the TWL4030 GPIO direction if the offset was < TWL4030_GPIO_MAX, and anything greater used twl4030_led_set_value as part of twl_set to setup the LED pin. However, with the commit mentioned above, LEDa pin request will result in fail as the GPIO number for LEDa is equal to TWL4030_GPIO_MAX and USB fails to function on beagleboard-xm. This is reported in the log as:hsusb2_vbus: Failed to request enable GPIO510: -22
To fix this, we should handle the fail case of twl4030_set_gpio_direction independent of the offset < TWL4030_GPIO_MAX check.
---
Applies on v3.13-rc3
Tested on beagleboard-xm which uses ethernet over usb:
before the patch (USB regression): http://pastebin.mozilla.org/3769443
After this patch: http://pastebin.mozilla.org/3769454
drivers/gpio/gpio-twl4030.c | 9 +++++++-- 1 file changed, 7 insertions(+), 2 deletions(-)
drivers/gpio/gpio-twl4030.c +7 -2
@@ -354,11 +354,16 @@ static void twl_set(struct gpio_chip *chip, unsigned offset, int value)static int twl_direction_out (struct gpio_chip *chip,unsigned offset,int value) {struct gpio_twl4030_priv *priv =to_gpio_twl4030 (chip); -int ret = -EINVAL ; +int ret =0 ;mutex_lock (&priv->mutex); -if (offset <TWL4030_GPIO_MAX ) +if (offset <TWL4030_GPIO_MAX ) { ret =twl4030_set_gpio_direction (offset,0 ); +if (ret) { +mutex_unlock (&priv->mutex); +return ret; + } + } priv->direction |=BIT (offset);mutex_unlock (&priv->mutex);
Signature · 1 line
1.7.9.5
Quoted 13 lines · Nishanth Menon
Commit 0b2aa8b (gpio: twl4030: Fix regression for twl gpio output) introduces yet another regression by ignoring the fact that we use twl gpio even for LED. For example, leda (offset 18) is used for USB port2 power on beagleboard-xm.
The original logic was supposed to setup the TWL4030 GPIO direction if the offset was <
TWL4030_GPIO_MAX, and anything greater usedtwl4030_led_set_valueas part oftwl_setto setup the LED pin. However, with the commit mentioned above, LEDa pin request will result in fail as the GPIO number for LEDa is equal toTWL4030_GPIO_MAXand USB fails to function on beagleboard-xm. This is reported in the log as:hsusb2_vbus: Failed to request enable GPIO510: -22
Quoted 3 lines
To fix this, we should handle the fail case of
twl4030_set_gpio_directionindependent of the offset <TWL4030_GPIO_MAXcheck.
Heh again :) Linus has already queued a similar fix, see "[PATCH v2 1/1] gpio: twl4030: Fix regression for twl gpio LED output".
Regards,
Tony
Quoted 37 lines
Signed-off-by Nishanth Menon <[email protected]>---
Applies on v3.13-rc3Tested on beagleboard-xm which uses ethernet over usb:
before the patch (USB regression): http://pastebin.mozilla.org/3769443
After this patch: http://pastebin.mozilla.org/3769454drivers/gpio/gpio-twl4030.c | 9 +++++++-- 1 file changed, 7 insertions(+), 2 deletions(-)drivers/gpio/gpio-twl4030.c +7
-2@@ -354,11 +354,16 @@ static void twl_set(struct gpio_chip *chip, unsigned offset, int value)static int twl_direction_out (struct gpio_chip *chip,unsigned offset,int value) {struct gpio_twl4030_priv *priv =to_gpio_twl4030 (chip); -int ret = -EINVAL ; +int ret =0 ;mutex_lock (&priv->mutex); -if (offset <TWL4030_GPIO_MAX ) +if (offset <TWL4030_GPIO_MAX ) { ret =twl4030_set_gpio_direction (offset,0 ); +if (ret) { +mutex_unlock (&priv->mutex); +return ret; + } + } priv->direction |=BIT (offset);mutex_unlock (&priv->mutex);Signature · 1 line
1.7.9.5
Quoted 14 lines · Tony Lindgren
Quoted 13 lines · Nishanth Menon
Commit 0b2aa8b (gpio: twl4030: Fix regression for twl gpio output) introduces yet another regression by ignoring the fact that we use twl gpio even for LED. For example, leda (offset 18) is used for USB port2 power on beagleboard-xm.
The original logic was supposed to setup the TWL4030 GPIO direction if the offset was <
TWL4030_GPIO_MAX, and anything greater usedtwl4030_led_set_valueas part oftwl_setto setup the LED pin. However, with the commit mentioned above, LEDa pin request will result in fail as the GPIO number for LEDa is equal toTWL4030_GPIO_MAXand USB fails to function on beagleboard-xm. This is reported in the log as:hsusb2_vbus: Failed to request enable GPIO510: -22
Quoted 7 lines
Quoted 3 lines
To fix this, we should handle the fail case of
twl4030_set_gpio_directionindependent of the offset <TWL4030_GPIO_MAXcheck.Heh again :) Linus has already queued a similar fix, see "[PATCH v2 1/1] gpio: twl4030: Fix regression for twl gpio LED output".
Alrite, I admit it, I need a vacation ;).. Sigh..
http://marc.info/?l=linux-gpio&w=2&r=1&s=twl4030&q=t is not good enough :(..
Signature · 2 lines
Regards, Nishanth Menon