Skip to contentSkip to conversation

mfd: rtsx: decrease driver size and add new device

PATCH In review [email protected] 3 participants 5 messages Dec 18, 2013 Multifunction devices (MFD)

lore
Share & tools
lore
#0 lore raw

v4 cover mfd: rtsx: decrease driver size and add new device

From: Micky Ching <[email protected]>

we add a macro to simplify setting pull control, and use a common init function to init the common params for 8411-like chips. at last we add support for rtl8402 chip.

Micky Ching (2):
mfd: rtsx: add set pull control macro and simplify rtl8411
mfd: rtsx: add support for card reader rtl8402

 drivers/mfd/rtl8411.c  |   95 ++++++++++++++++++++++++++----------------------
 drivers/mfd/rtsx_pcr.c |    5 +++
 drivers/mfd/rtsx_pcr.h |    9 +++++
 3 files changed, 66 insertions(+), 43 deletions(-)

--
1.7.9.5

#1 lore raw

PATCH v4 1/2 mfd: rtsx: add set pull control macro and simplify rtl8411

From: Micky Ching <[email protected]>

add set pull control macro to reduce code for setting pull control, and use a common init function to reduce code for rtl8411.c. So this patch is used to just simplify code.

---
 drivers/mfd/rtl8411.c  |   53 ++++++++++++------------------------------------
 drivers/mfd/rtsx_pcr.h |    8 ++++++++
 2 files changed, 21 insertions(+), 40 deletions(-)
drivers/mfd/rtl8411.c +13 -40
index 5280135..00ecf6b 100644
@@ -441,12 +441,10 @@ static const u32 rtl8411b_qfn48_ms_pull_ctl_disable_tbl[] = {
 	0,
 };
 
-void rtl8411_init_params(struct rtsx_pcr *pcr)
+void rtl8411_init_common_params(struct rtsx_pcr *pcr)
 {
 	pcr->extra_caps = EXTRA_CAPS_SD_SDR50 | EXTRA_CAPS_SD_SDR104;
 	pcr->num_slots = 2;
-	pcr->ops = &rtl8411_pcr_ops;
-
 	pcr->flags = 0;
 	pcr->card_drive_sel = RTL8411_CARD_DRIVE_DEFAULT;
 	pcr->sd30_drive_sel_1v8 = DRIVER_TYPE_B;
@@ -454,47 +452,22 @@ void rtl8411_init_params(struct rtsx_pcr *pcr)
 	pcr->aspm_en = ASPM_L1_EN;
 	pcr->tx_initial_phase = SET_CLOCK_PHASE(23, 7, 14);
 	pcr->rx_initial_phase = SET_CLOCK_PHASE(4, 3, 10);
-
 	pcr->ic_version = rtl8411_get_ic_version(pcr);
-	pcr->sd_pull_ctl_enable_tbl = rtl8411_sd_pull_ctl_enable_tbl;
-	pcr->sd_pull_ctl_disable_tbl = rtl8411_sd_pull_ctl_disable_tbl;
-	pcr->ms_pull_ctl_enable_tbl = rtl8411_ms_pull_ctl_enable_tbl;
-	pcr->ms_pull_ctl_disable_tbl = rtl8411_ms_pull_ctl_disable_tbl;
+}
+
+void rtl8411_init_params(struct rtsx_pcr *pcr)
+{
+	rtl8411_init_common_params(pcr);
+	pcr->ops = &rtl8411_pcr_ops;
+	set_pull_ctrl_tables(pcr, rtl8411);
 }
 
 void rtl8411b_init_params(struct rtsx_pcr *pcr)
 {
-	pcr->extra_caps = EXTRA_CAPS_SD_SDR50 | EXTRA_CAPS_SD_SDR104;
-	pcr->num_slots = 2;
+	rtl8411_init_common_params(pcr);
 	pcr->ops = &rtl8411b_pcr_ops;
-
-	pcr->flags = 0;
-	pcr->card_drive_sel = RTL8411_CARD_DRIVE_DEFAULT;
-	pcr->sd30_drive_sel_1v8 = DRIVER_TYPE_B;
-	pcr->sd30_drive_sel_3v3 = DRIVER_TYPE_D;
-	pcr->aspm_en = ASPM_L1_EN;
-	pcr->tx_initial_phase = SET_CLOCK_PHASE(23, 7, 14);
-	pcr->rx_initial_phase = SET_CLOCK_PHASE(4, 3, 10);
-
-	pcr->ic_version = rtl8411_get_ic_version(pcr);
-
-	if (rtl8411b_is_qfn48(pcr)) {
-		pcr->sd_pull_ctl_enable_tbl =
-			rtl8411b_qfn48_sd_pull_ctl_enable_tbl;
-		pcr->sd_pull_ctl_disable_tbl =
-			rtl8411b_qfn48_sd_pull_ctl_disable_tbl;
-		pcr->ms_pull_ctl_enable_tbl =
-			rtl8411b_qfn48_ms_pull_ctl_enable_tbl;
-		pcr->ms_pull_ctl_disable_tbl =
-			rtl8411b_qfn48_ms_pull_ctl_disable_tbl;
-	} else {
-		pcr->sd_pull_ctl_enable_tbl =
-			rtl8411b_qfn64_sd_pull_ctl_enable_tbl;
-		pcr->sd_pull_ctl_disable_tbl =
-			rtl8411b_qfn64_sd_pull_ctl_disable_tbl;
-		pcr->ms_pull_ctl_enable_tbl =
-			rtl8411b_qfn64_ms_pull_ctl_enable_tbl;
-		pcr->ms_pull_ctl_disable_tbl =
-			rtl8411b_qfn64_ms_pull_ctl_disable_tbl;
-	}
+	if (rtl8411b_is_qfn48(pcr))
+		set_pull_ctrl_tables(pcr, rtl8411b_qfn48);
+	else
+		set_pull_ctrl_tables(pcr, rtl8411b_qfn64);
 }
drivers/mfd/rtsx_pcr.h +8 -0
index 947e79b..e9feadb 100644
@@ -63,4 +63,12 @@ static inline u8 map_sd_drive(int idx)
 #define rtl8411_reg_to_sd30_drive_sel_3v3(reg)	(((reg) >> 5) & 0x07)
 #define rtl8411b_reg_to_sd30_drive_sel_3v3(reg)	((reg) & 0x03)
 
+#define set_pull_ctrl_tables(pcr, __device)				\
+do {									\
+	pcr->sd_pull_ctl_enable_tbl  = __device##_sd_pull_ctl_enable_tbl;  \
+	pcr->sd_pull_ctl_disable_tbl = __device##_sd_pull_ctl_disable_tbl; \
+	pcr->ms_pull_ctl_enable_tbl  = __device##_ms_pull_ctl_enable_tbl;  \
+	pcr->ms_pull_ctl_disable_tbl = __device##_ms_pull_ctl_disable_tbl; \
+} while (0)
+
 #endif
Signature · 1 line
1.7.9.5
#2 lore raw

PATCH v4 2/2 mfd: rtsx: add support for card reader rtl8402

In reply to [email protected]

From: Micky Ching <[email protected]>

rtl8402 is much like rtl8411, so just add it to rtl8411.c

---
 drivers/mfd/rtl8411.c  |   44 ++++++++++++++++++++++++++++++++++++++++----
 drivers/mfd/rtsx_pcr.c |    5 +++++
 drivers/mfd/rtsx_pcr.h |    1 +
 3 files changed, 46 insertions(+), 4 deletions(-)
drivers/mfd/rtl8411.c +40 -4
index 00ecf6b..2d96552 100644
@@ -191,24 +191,25 @@ static int rtl8411_card_power_off(struct rtsx_pcr *pcr, int card)
 			BPP_LDO_POWB, BPP_LDO_SUSPEND);
 }
 
-static int rtl8411_switch_output_voltage(struct rtsx_pcr *pcr, u8 voltage)
+static int rtl8411_do_switch_output_voltage(struct rtsx_pcr *pcr, u8 voltage,
+		int bpp_tuned18_shift, int bpp_asic_1v8)
 {
 	u8 mask, val;
 	int err;
 
-	mask = (BPP_REG_TUNED18 << BPP_TUNED18_SHIFT_8411) | BPP_PAD_MASK;
+	mask = (BPP_REG_TUNED18 << bpp_tuned18_shift) | BPP_PAD_MASK;
 	if (voltage == OUTPUT_3V3) {
 		err = rtsx_pci_write_register(pcr,
 				SD30_DRIVE_SEL, 0x07, pcr->sd30_drive_sel_3v3);
 		if (err < 0)
 			return err;
-		val = (BPP_ASIC_3V3 << BPP_TUNED18_SHIFT_8411) | BPP_PAD_3V3;
+		val = (BPP_ASIC_3V3 << bpp_tuned18_shift) | BPP_PAD_3V3;
 	} else if (voltage == OUTPUT_1V8) {
 		err = rtsx_pci_write_register(pcr,
 				SD30_DRIVE_SEL, 0x07, pcr->sd30_drive_sel_1v8);
 		if (err < 0)
 			return err;
-		val = (BPP_ASIC_1V8 << BPP_TUNED18_SHIFT_8411) | BPP_PAD_1V8;
+		val = (bpp_asic_1v8 << bpp_tuned18_shift) | BPP_PAD_1V8;
 	} else {
 		return -EINVAL;
 	}
@@ -216,6 +217,18 @@ static int rtl8411_switch_output_voltage(struct rtsx_pcr *pcr, u8 voltage)
 	return rtsx_pci_write_register(pcr, LDO_CTL, mask, val);
 }
 
+static int rtl8411_switch_output_voltage(struct rtsx_pcr *pcr, u8 voltage)
+{
+	return rtl8411_do_switch_output_voltage(pcr, voltage,
+			BPP_TUNED18_SHIFT_8411, BPP_ASIC_1V8);
+}
+
+static int rtl8402_switch_output_voltage(struct rtsx_pcr *pcr, u8 voltage)
+{
+	return rtl8411_do_switch_output_voltage(pcr, voltage,
+			BPP_TUNED18_SHIFT_8402, BPP_ASIC_2V0);
+}
+
 static unsigned int rtl8411_cd_deglitch(struct rtsx_pcr *pcr)
 {
 	unsigned int card_exist;
@@ -295,6 +308,22 @@ static const struct pcr_ops rtl8411_pcr_ops = {
 	.force_power_down = rtl8411_force_power_down,
 };
 
+static const struct pcr_ops rtl8402_pcr_ops = {
+	.fetch_vendor_settings = rtl8411_fetch_vendor_settings,
+	.extra_init_hw = rtl8411_extra_init_hw,
+	.optimize_phy = NULL,
+	.turn_on_led = rtl8411_turn_on_led,
+	.turn_off_led = rtl8411_turn_off_led,
+	.enable_auto_blink = rtl8411_enable_auto_blink,
+	.disable_auto_blink = rtl8411_disable_auto_blink,
+	.card_power_on = rtl8411_card_power_on,
+	.card_power_off = rtl8411_card_power_off,
+	.switch_output_voltage = rtl8402_switch_output_voltage,
+	.cd_deglitch = rtl8411_cd_deglitch,
+	.conv_clk_and_div_n = rtl8411_conv_clk_and_div_n,
+	.force_power_down = rtl8411_force_power_down,
+};
+
 static const struct pcr_ops rtl8411b_pcr_ops = {
 	.fetch_vendor_settings = rtl8411b_fetch_vendor_settings,
 	.extra_init_hw = rtl8411b_extra_init_hw,
@@ -471,3 +500,10 @@ void rtl8411b_init_params(struct rtsx_pcr *pcr)
 	else
 		set_pull_ctrl_tables(pcr, rtl8411b_qfn64);
 }
+
+void rtl8402_init_params(struct rtsx_pcr *pcr)
+{
+	rtl8411_init_common_params(pcr);
+	pcr->ops = &rtl8402_pcr_ops;
+	set_pull_ctrl_tables(pcr, rtl8411);
+}
drivers/mfd/rtsx_pcr.c +5 -0
index 11e20af..2af55bb 100644
@@ -57,6 +57,7 @@ static DEFINE_PCI_DEVICE_TABLE(rtsx_pci_ids) = {
 	{ PCI_DEVICE(0x10EC, 0x5227), PCI_CLASS_OTHERS << 16, 0xFF0000 },
 	{ PCI_DEVICE(0x10EC, 0x5249), PCI_CLASS_OTHERS << 16, 0xFF0000 },
 	{ PCI_DEVICE(0x10EC, 0x5287), PCI_CLASS_OTHERS << 16, 0xFF0000 },
+	{ PCI_DEVICE(0x10EC, 0x5286), PCI_CLASS_OTHERS << 16, 0xFF0000 },
 	{ 0, }
 };
 
@@ -1061,6 +1062,10 @@ static int rtsx_pci_init_chip(struct rtsx_pcr *pcr)
 	case 0x5287:
 		rtl8411b_init_params(pcr);
 		break;
+
+	case 0x5286:
+		rtl8402_init_params(pcr);
+		break;
 	}
 
 	dev_dbg(&(pcr->pci->dev), "PID: 0x%04x, IC version: 0x%02x\n",
drivers/mfd/rtsx_pcr.h +1 -0
index e9feadb..07e4c2e 100644
@@ -30,6 +30,7 @@
 void rts5209_init_params(struct rtsx_pcr *pcr);
 void rts5229_init_params(struct rtsx_pcr *pcr);
 void rtl8411_init_params(struct rtsx_pcr *pcr);
+void rtl8402_init_params(struct rtsx_pcr *pcr);
 void rts5227_init_params(struct rtsx_pcr *pcr);
 void rts5249_init_params(struct rtsx_pcr *pcr);
 void rtl8411b_init_params(struct rtsx_pcr *pcr);
Signature · 1 line
1.7.9.5
Reviewed-by on the v4 series
#3 lore raw
In reply to [email protected]
Quoted 6 lines · On Wed, Dec 18, 2013 at 10:03:11AM +0800, [email protected] wrote:

From: Micky Ching <[email protected]>

we add a macro to simplify setting pull control, and use a common init function to init the common params for 8411-like chips. at last we add support for rtl8402 chip.

Quoted 9 lines

Micky Ching (2):
mfd: rtsx: add set pull control macro and simplify rtl8411
mfd: rtsx: add support for card reader rtl8402

 drivers/mfd/rtl8411.c  |   95 ++++++++++++++++++++++++++----------------------
 drivers/mfd/rtsx_pcr.c |    5 +++
 drivers/mfd/rtsx_pcr.h |    9 +++++
 3 files changed, 66 insertions(+), 43 deletions(-)

Great. Looks good to me.

regards,
dan carpenter

#4 lore raw
In reply to [email protected]
Quoted 6 lines · On Wed, 18 Dec 2013, [email protected] wrote:

From: Micky Ching <[email protected]>

we add a macro to simplify setting pull control, and use a common init function to init the common params for 8411-like chips. at last we add support for rtl8402 chip.

Quoted 8 lines

Micky Ching (2):
mfd: rtsx: add set pull control macro and simplify rtl8411
mfd: rtsx: add support for card reader rtl8402

 drivers/mfd/rtl8411.c  |   95 ++++++++++++++++++++++++++----------------------
 drivers/mfd/rtsx_pcr.c |    5 +++
 drivers/mfd/rtsx_pcr.h |    9 +++++
 3 files changed, 66 insertions(+), 43 deletions(-)

Nice.

Applied with Dan's Reviewed-by.

Signature · 4 lines
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog