ARM: Kirkwood: Add 6192 DTSI file
PATCH 1/2 ARM: Kirkwood: Add 6192 DTSI file
This file is mainly a copy of kirkwood-6281.dtsi.
The pinctrl seems to be the same.
These platforms differs only with their CPU, memory capabilities and the number of GPIO available (36 on 6192, 50 on 6281).
--- arch/arm/boot/dts/kirkwood-6192.dtsi | 107 +++++++++++++++++++++++++++++++++++ 1 file changed, 107 insertions(+) create mode 100644 arch/arm/boot/dts/kirkwood-6192.dtsi
arch/arm/boot/dts/kirkwood-6192.dtsi new file +107 -0
@@ -0,0 +1,107 @@ +/ { + mbus { + pcie-controller { + compatible = "marvell,kirkwood-pcie"; + status = "disabled"; + device_type = "pci"; + + #address-cells = <3>; + #size-cells = <2>; + + bus-range = <0x00 0xff>; + + ranges = + <0x82000000 0 0x40000 MBUS_ID(0xf0, 0x01) 0x40000 0 0x00002000 + 0x82000000 0x1 0 MBUS_ID(0x04, 0xe8) 0 1 0 /* Port 0.0 MEM */ + 0x81000000 0x1 0 MBUS_ID(0x04, 0xe0) 0 1 0 /* Port 0.0 IO */>; + + pcie at 1,0 { + device_type = "pci"; + assigned-addresses = <0x82000800 0 0x00040000 0 0x2000>; + reg = <0x0800 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0 + 0x81000000 0 0 0x81000000 0x1 0 1 0>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &intc 9>; + marvell,pcie-port = <0>; + marvell,pcie-lane = <0>; + clocks = <&gate_clk 2>; + status = "disabled"; + }; + }; + }; + + ocp at f1000000 { + pinctrl: pinctrl at 10000 { + compatible = "marvell,88f6192-pinctrl"; + reg = <0x10000 0x20>; + + pmx_nand: pmx-nand { + marvell,pins = "mpp0", "mpp1", "mpp2", "mpp3", + "mpp4", "mpp5", "mpp18", + "mpp19"; + marvell,function = "nand"; + }; + pmx_sata0: pmx-sata0 { + marvell,pins = "mpp5", "mpp21", "mpp23"; + marvell,function = "sata0"; + }; + pmx_sata1: pmx-sata1 { + marvell,pins = "mpp4", "mpp20", "mpp22"; + marvell,function = "sata1"; + }; + pmx_spi: pmx-spi { + marvell,pins = "mpp0", "mpp1", "mpp2", "mpp3"; + marvell,function = "spi"; + }; + pmx_twsi0: pmx-twsi0 { + marvell,pins = "mpp8", "mpp9"; + marvell,function = "twsi0"; + }; + pmx_uart0: pmx-uart0 { + marvell,pins = "mpp10", "mpp11"; + marvell,function = "uart0"; + }; + pmx_uart1: pmx-uart1 { + marvell,pins = "mpp13", "mpp14"; + marvell,function = "uart1"; + }; + pmx_sdio: pmx-sdio { + marvell,pins = "mpp12", "mpp13", "mpp14", + "mpp15", "mpp16", "mpp17"; + marvell,function = "sdio"; + }; + }; + + rtc at 10300 { + compatible = "marvell,kirkwood-rtc", "marvell,orion-rtc"; + reg = <0x10300 0x20>; + interrupts = <53>; + clocks = <&gate_clk 7>; + }; + + sata at 80000 { + compatible = "marvell,orion-sata"; + reg = <0x80000 0x5000>; + interrupts = <21>; + clocks = <&gate_clk 14>, <&gate_clk 15>; + clock-names = "0", "1"; + status = "disabled"; + }; + + mvsdio at 90000 { + compatible = "marvell,orion-sdio"; + reg = <0x90000 0x200>; + interrupts = <28>; + clocks = <&gate_clk 4>; + bus-width = <4>; + cap-sdio-irq; + cap-sd-highspeed; + cap-mmc-highspeed; + status = "disabled"; + }; + }; +};
Signature · 1 line
1.8.5.1
PATCH 2/2 ARM: Kirkwood: DT board setup for LaPlug
This patch adds DT board setup for the LaCie NAS LaPlug.
Chipset list:
- CPU MARVELL 88FR131 800Mhz
- SDRAM memory: 128MB DDR2-800 400Mhz
- 1 Ethernet Gigabit port (PHY MARVELL 88E1318)
- 1 Mini PCI-Express port
- 1 NAND 512 MB
- 1 push button
- 2 LEDs (red and blue)
- 4 USB Ports
---
Changes v1 -> v2:
- Rename the board from ns-plug to laplug, changes everywhere accordingly
- Retab the files
- Use defines for GPIO active state and key input's name.
- Remove #*-cells in gpio-keys as this is not a bus
- Use kirkwood-6192.dtsi
--- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/kirkwood-laplug.dts | 175 ++++++++++++++++++++++++++++++++++ 2 files changed, 176 insertions(+) create mode 100644 arch/arm/boot/dts/kirkwood-laplug.dts
arch/arm/boot/dts/Makefile +1 -0
@@ -85,6 +85,7 @@ dtb-$(CONFIG_ARCH_KIRKWOOD) += kirkwood-cloudbox.dtb \ kirkwood-iomega_ix2_200.dtb \ kirkwood-is2.dtb \ kirkwood-km_kirkwood.dtb \ + kirkwood-laplug.dtb \ kirkwood-lschlv2.dtb \ kirkwood-lsxhl.dtb \ kirkwood-mplcec4.dtb \
arch/arm/boot/dts/kirkwood-laplug.dts new file +175 -0
175 lines not on this page · raw message
Signature · 1 line
1.8.5.1
PATCH 2/2 ARM: Kirkwood: DT board setup for LaPlug
I have a slight issue which I could not resolve regarding the Hynix NAND on this platform. Although it worked perfectly well with 3.12, the device is not detected anymore with the current head of master.
There is no warning nor bug that I could find. It just not detected. Since I don't really know how to debug this, maybe doing git bisect ? Some advice would be greatly welcomed !
Quoted 223 lines · Maxime Hadjinlian
This patch adds DT board setup for the LaCie NAS LaPlug.
Chipset list:
- CPU MARVELL 88FR131 800Mhz
- SDRAM memory: 128MB DDR2-800 400Mhz
- 1 Ethernet Gigabit port (PHY MARVELL 88E1318)
- 1 Mini PCI-Express port
- 1 NAND 512 MB
- 1 push button
- 2 LEDs (red and blue)
- 4 USB PortsSigned-off-by Maxime Hadjinlian <[email protected]>---
Changes v1 -> v2:
- Rename the board from ns-plug to laplug, changes everywhere accordingly
- Retab the files
- Use defines for GPIO active state and key input's name.
- Remove #*-cells in gpio-keys as this is not a bus
- Usekirkwood-6192.dtsi--- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/kirkwood-laplug.dts | 175 ++++++++++++++++++++++++++++++++++ 2 files changed, 176 insertions(+) create mode 100644 arch/arm/boot/dts/kirkwood-laplug.dtsarch/arm/boot/dts/Makefile +1
-0@@ -85,6 +85,7 @@ dtb-$(CONFIG_ARCH_KIRKWOOD) += kirkwood-cloudbox.dtb \ kirkwood-iomega_ix2_200.dtb \ kirkwood-is2.dtb \ kirkwood-km_kirkwood.dtb \ + kirkwood-laplug.dtb \ kirkwood-lschlv2.dtb \ kirkwood-lsxhl.dtb \ kirkwood-mplcec4.dtb \arch/arm/boot/dts/kirkwood-laplug.dts new file +175
-1@@ -0,0 +1,175 @@ +/* + * Copyright (C) 2013 Maxime Hadjinlian <[email protected]> + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +/dts-v1/; + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> +#include "kirkwood.dtsi" +#include "kirkwood-6192.dtsi" + +/ { + model = "LaCie LaPlug"; + compatible = "lacie,laplug", "marvell,kirkwood-88f6192", "marvell,kirkwood"; + + memory { + device_type = "memory"; + reg = <0x00000000 0x8000000>; /* 128 MB */ + }; + + chosen { + bootargs = "console=ttyS0,115200n8 earlyprintk"; + }; + + mbus { + ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000>; + pcie-controller { + status = "okay"; + pcie at 1,0 { + status = "okay"; + }; + }; + }; + + ocp at f1000000 { + serial at 12000 { + pinctrl-0 = <&pmx_uart0>; + pinctrl-names = "default"; + status = "okay"; + }; + + i2c at 11000 { + pinctrl-0 = <&pmx_twsi0>; + pinctrl-names = "default"; + status = "okay"; + + eeprom at 50 { + compatible = "at,24c04"; + pagesize = <16>; + reg = <0x50>; + }; + }; + + pinctrl: pinctrl at 10000 { + pmx_usb_power_enable: pmx-usb-power-enable { + marvell,pins = "mpp14"; + marvell,function = "gpio"; + }; + }; + }; + + gpio_keys { + compatible = "gpio-keys"; + + button at 1{ + label = "Power push button"; + linux,code = <KEY_POWER>; + gpios = <&gpio1 0 GPIO_ACTIVE_HIGH>; + }; + }; + + gpio-leds { + compatible = "gpio-leds"; + + red-fail { + label = "laplug_v2:red:power"; + gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>; + }; + blue-power { + label = "laplug_v2:blue:power"; + gpios = <&gpio0 29 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "default-on"; + }; + }; + + gpio_poweroff { + compatible = "gpio-poweroff"; + gpios = <&gpio0 31 GPIO_ACTIVE_HIGH>; + }; + + regulators { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; + pinctrl-0 = <&pmx_usb_power_enable>; + pinctrl-names = "default"; + + usb_power_back1: regulator at 1 { + compatible = "regulator-fixed"; + reg = <1>; + regulator-name = "USB Power Back 1"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + regulator-always-on; + regulator-boot-on; + gpio = <&gpio0 15 GPIO_ACTIVE_HIGH>; + }; + + usb_power_back2: regulator at 2 { + compatible = "regulator-fixed"; + reg = <2>; + regulator-name = "USB Power Back 2"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + regulator-always-on; + regulator-boot-on; + gpio = <&gpio0 28 GPIO_ACTIVE_HIGH>; + }; + + usb_power_front: regulator at 3 { + compatible = "regulator-fixed"; + reg = <3>; + regulator-name = "USB Power Front"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + regulator-always-on; + regulator-boot-on; + gpio = <&gpio1 3 GPIO_ACTIVE_HIGH>; + }; + }; +}; + +&nand { + /* Total size : 512MB */ + status = "okay"; + + partition at 0 { + label = "u-boot"; + reg = <0x0 0x100000>; /* 1MB */ + read-only; + }; + + partition at 100000 { + label = "uImage"; + reg = <0x100000 0x1000000>; /* 16MB */ + }; + + partition at 1100000 { + label = "rootfs"; + reg = <0x1100000 0x1EF00000>; /* 495MB */ + }; +}; + +&mdio { + status = "okay"; + + ethphy0: ethernet-phy at 0 { + device_type = "ethernet-phy"; + reg = <0>; + }; +}; + +ð0 { + status = "okay"; + ethernet0-port at 0 { + phy-handle = <ðphy0>; + }; +}; --1.8.5.1
PATCH 2/2 ARM: Kirkwood: DT board setup for LaPlug
Quoted 7 lines · Maxime Hadjinlian
I have a slight issue which I could not resolve regarding the Hynix NAND on this platform. Although it worked perfectly well with 3.12, the device is not detected anymore with the current head of master.
There is no warning nor bug that I could find. It just not detected. Since I don't really know how to debug this, maybe doing git bisect ? Some advice would be greatly welcomed !
Hi Maxime
git bisect sounds like the right thing to do. Once we know which patch introduced the issue it becomes a lot easier to fix.
Thanks
Andrew
PATCH 2/2 ARM: Kirkwood: DT board setup for LaPlug
In reply to Maxime HadjinlianHi Maxime,
Quoted 4 lines · Maxime Hadjinlian
I have a slight issue which I could not resolve regarding the Hynix NAND on this platform. Although it worked perfectly well with 3.12, the device is not detected anymore with the current head of master.
If you do a "git log v3.12..v3.13-rc4 -- drivers/mtd/nand/orion_nand.c" you'll see that no changes have been made.
So maybe this new dts v2 is the problem. And if you look in detail you'll find you've been bitten by the subtleties of the devicetree!
See below...
Quoted 9 lines
arch/arm/boot/dts/kirkwood-laplug.dts line 37
Quoted 9 lines
arch/arm/boot/dts/kirkwood-laplug.dts new file +9
-0+ mbus { + ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000>; + pcie-controller { + status = "okay"; + pcie at 1,0 { + status = "okay"; + }; + }; + };
^^^^
Here's the problem: there's two wrong things with the above:
1. You can't do this... a ranges properties doesn't add on the included (dtsi) ranges properties. Instead it replaces the included one, so you have to write the entries all over again.
Yes, we know: it sucks! And given we know it sucks, there was a nice message warning you about this. From the kirkwood.dtsi
/* If a board file needs to change this ranges it must replace it completely */ ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000 /* internal-regs */ MBUS_ID(0x01, 0x2f) 0 0xf4000000 0x10000 /* nand flash */ MBUS_ID(0x03, 0x01) 0 0xf5000000 0x10000 /* crypto sram */ >;
2. Looking in yet more detail, you're re-adding the internal-regs window. I guess it's just a typo, no?
Anyway, I *think* that's what prevented you from getting the NAND to work. The correct mbus node should be:
mbus {
pcie-controller {
status = "okay";
pcie at 1,0 {
status = "okay";
};
};
};Quoted 4 lines
arch/arm/boot/dts/kirkwood-laplug.dts line 143
Quoted 4 lines
+&nand {
arch/arm/boot/dts/kirkwood-laplug.dts new file +3
-0+ /* Total size : 512MB */ + status = "okay"; +
And here: don't you need to add the pinmuxing? Maybe you don't need it, but I guess it's the right thing to do.
I hope this helps!
Merry Christmas...
Signature · 3 lines
Ezequiel Garc?a, Free Electrons Embedded Linux, Kernel and Android Engineering http://free-electrons.com
PATCH 2/2 ARM: Kirkwood: DT board setup for LaPlug
Quoted 1 line · Ezequiel Garcia
Hi Maxime,
Hi Ezequiel
Quoted 61 lines · Maxime Hadjinlian
Quoted 4 lines
I have a slight issue which I could not resolve regarding the Hynix NAND on this platform. Although it worked perfectly well with 3.12, the device is not detected anymore with the current head of master.
If you do a "git log v3.12..v3.13-rc4 --
drivers/mtd/nand/orion_nand.c" you'll see that no changes have been made.So maybe this new dts v2 is the problem. And if you look in detail you'll find you've been bitten by the subtleties of the devicetree!
See below...
Quoted 9 lines
arch/arm/boot/dts/kirkwood-laplug.dts line 37
Quoted 9 lines
arch/arm/boot/dts/kirkwood-laplug.dts new file +9
-0+ mbus { + ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000>; + pcie-controller { + status = "okay"; + pcie at 1,0 { + status = "okay"; + }; + }; + };^^^^
Here's the problem: there's two wrong things with the above:1. You can't do this... a ranges properties doesn't add on the included (dtsi) ranges properties. Instead it replaces the included one, so you have to write the entries all over again.
Yes, we know: it sucks! And given we know it sucks, there was a nice message warning you about this. From the
kirkwood.dtsi/* If a board file needs to change this ranges it must replace it completely */ ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000 /* internal-regs */ MBUS_ID(0x01, 0x2f) 0 0xf4000000 0x10000 /* nand flash */ MBUS_ID(0x03, 0x01) 0 0xf5000000 0x10000 /* crypto sram */ >;2. Looking in yet more detail, you're re-adding the internal-regs window. I guess it's just a typo, no?
Anyway, I *think* that's what prevented you from getting the NAND to work. The correct mbus node should be:
mbus { pcie-controller { status = "okay"; pcie at 1,0 { status = "okay"; }; }; };Quoted 4 lines
arch/arm/boot/dts/kirkwood-laplug.dts line 143
Quoted 4 lines
+&nand {
arch/arm/boot/dts/kirkwood-laplug.dts new file +3
-0+ /* Total size : 512MB */ + status = "okay"; +
Quoted 4 lines
And here: don't you need to add the pinmuxing? Maybe you don't need it, but I guess it's the right thing to do.
I hope this helps!
That was it ! Thank you very much, I will resend a v3. Thank you very much. I will be more carefarch/arm/boot/dts/kirkwood-laplug.dtsull about this next time.
Quoted 2 lines
Merry Christmas...
Merry Christmas to you.
Quoted 4 lines
--
Ezequiel Garc?a, Free Electrons
Embedded Linux, Kernel and Android Engineering
http://free-electrons.com
PATCH 2/2 ARM: Kirkwood: DT board setup for LaPlug
In reply to Maxime HadjinlianQuoted 49 lines · Maxime Hadjinlian
This patch adds DT board setup for the LaCie NAS LaPlug.
Chipset list:
- CPU MARVELL 88FR131 800Mhz
- SDRAM memory: 128MB DDR2-800 400Mhz
- 1 Ethernet Gigabit port (PHY MARVELL 88E1318)
- 1 Mini PCI-Express port
- 1 NAND 512 MB
- 1 push button
- 2 LEDs (red and blue)
- 4 USB PortsSigned-off-by Maxime Hadjinlian <[email protected]>---
Changes v1 -> v2:
- Rename the board from ns-plug to laplug, changes everywhere accordingly
- Retab the files
- Use defines for GPIO active state and key input's name.
- Remove #*-cells in gpio-keys as this is not a bus
- Usekirkwood-6192.dtsi--- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/kirkwood-laplug.dts | 175 ++++++++++++++++++++++++++++++++++ 2 files changed, 176 insertions(+) create mode 100644 arch/arm/boot/dts/kirkwood-laplug.dtsarch/arm/boot/dts/Makefile +1
-0@@ -85,6 +85,7 @@ dtb-$(CONFIG_ARCH_KIRKWOOD) += kirkwood-cloudbox.dtb \ kirkwood-iomega_ix2_200.dtb \ kirkwood-is2.dtb \ kirkwood-km_kirkwood.dtb \ + kirkwood-laplug.dtb \ kirkwood-lschlv2.dtb \ kirkwood-lsxhl.dtb \ kirkwood-mplcec4.dtb \arch/arm/boot/dts/kirkwood-laplug.dts new file +4
-0@@ -0,0 +1,175 @@ +/* + * Copyright (C) 2013 Maxime Hadjinlian <[email protected]> + * + * This file is licensed under the terms of the GNU General Public
arch/arm/boot/dts/kirkwood-laplug.dts line 14
Quoted 10 lines
arch/arm/boot/dts/kirkwood-laplug.dts new file +10
-0+ * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +/dts-v1/; + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> +#include "kirkwood.dtsi" +#include "kirkwood-6192.dtsi"
Hi Maxime
Thanks for the v2. Looks good.
When using Jason's DT branch, the includes for gpio and input are no longer needed, kirkwood.dtsi has them.
Quoted 164 lines
arch/arm/boot/dts/kirkwood-laplug.dts new file +161
-0+ +/ { + model = "LaCie LaPlug"; + compatible = "lacie,laplug", "marvell,kirkwood-88f6192", "marvell,kirkwood"; + + memory { + device_type = "memory"; + reg = <0x00000000 0x8000000>; /* 128 MB */ + }; + + chosen { + bootargs = "console=ttyS0,115200n8 earlyprintk"; + }; + + mbus { + ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000>; + pcie-controller { + status = "okay"; + pcie at 1,0 { + status = "okay"; + }; + }; + }; + + ocp at f1000000 { + serial at 12000 { + pinctrl-0 = <&pmx_uart0>; + pinctrl-names = "default"; + status = "okay"; + }; + + i2c at 11000 { + pinctrl-0 = <&pmx_twsi0>; + pinctrl-names = "default"; + status = "okay"; + + eeprom at 50 { + compatible = "at,24c04"; + pagesize = <16>; + reg = <0x50>; + }; + }; + + pinctrl: pinctrl at 10000 { + pmx_usb_power_enable: pmx-usb-power-enable { + marvell,pins = "mpp14"; + marvell,function = "gpio"; + }; + }; + }; + + gpio_keys { + compatible = "gpio-keys"; + + button at 1{ + label = "Power push button"; + linux,code = <KEY_POWER>; + gpios = <&gpio1 0 GPIO_ACTIVE_HIGH>; + }; + }; + + gpio-leds { + compatible = "gpio-leds"; + + red-fail { + label = "laplug_v2:red:power"; + gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>; + }; + blue-power { + label = "laplug_v2:blue:power"; + gpios = <&gpio0 29 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "default-on"; + }; + }; + + gpio_poweroff { + compatible = "gpio-poweroff"; + gpios = <&gpio0 31 GPIO_ACTIVE_HIGH>; + }; + + regulators { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; + pinctrl-0 = <&pmx_usb_power_enable>; + pinctrl-names = "default"; + + usb_power_back1: regulator at 1 { + compatible = "regulator-fixed"; + reg = <1>; + regulator-name = "USB Power Back 1"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + regulator-always-on; + regulator-boot-on; + gpio = <&gpio0 15 GPIO_ACTIVE_HIGH>; + }; + + usb_power_back2: regulator at 2 { + compatible = "regulator-fixed"; + reg = <2>; + regulator-name = "USB Power Back 2"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + regulator-always-on; + regulator-boot-on; + gpio = <&gpio0 28 GPIO_ACTIVE_HIGH>; + }; + + usb_power_front: regulator at 3 { + compatible = "regulator-fixed"; + reg = <3>; + regulator-name = "USB Power Front"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + regulator-always-on; + regulator-boot-on; + gpio = <&gpio1 3 GPIO_ACTIVE_HIGH>; + }; + }; +}; + +&nand { + /* Total size : 512MB */ + status = "okay"; + + partition at 0 { + label = "u-boot"; + reg = <0x0 0x100000>; /* 1MB */ + read-only; + }; + + partition at 100000 { + label = "uImage"; + reg = <0x100000 0x1000000>; /* 16MB */ + }; + + partition at 1100000 { + label = "rootfs"; + reg = <0x1100000 0x1EF00000>; /* 495MB */ + }; +}; + +&mdio { + status = "okay"; + + ethphy0: ethernet-phy at 0 { + device_type = "ethernet-phy"; + reg = <0>; + }; +}; + +ð0 { + status = "okay"; + ethernet0-port at 0 { + phy-handle = <ðphy0>; + }; +};Signature · 1 line
1.8.5.1
Thanks
Andrew
PATCH 1/2 ARM: Kirkwood: Add 6192 DTSI file
In reply to Maxime HadjinlianQuoted 10 lines · Maxime Hadjinlian
This file is mainly a copy of
kirkwood-6281.dtsi.
The pinctrl seems to be the same.
These platforms differs only with their CPU, memory capabilities and the number of GPIO available (36 on 6192, 50 on 6281).Signed-off-by Maxime Hadjinlian <[email protected]>--- arch/arm/boot/dts/kirkwood-6192.dtsi | 107 +++++++++++++++++++++++++++++++++++ 1 file changed, 107 insertions(+) create mode 100644 arch/arm/boot/dts/kirkwood-6192.dtsi
Hi Maxime
Jason recently sorted both 6181 and 6182. It would be nice if this file also used the same order. Take a look Jason's DT branch.
Thanks
Andrew
PATCH 1/2 ARM: Kirkwood: Add 6192 DTSI file
Quoted 6 lines · Andrew Lunn
Quoted 5 lines · Maxime Hadjinlian
This file is mainly a copy of
kirkwood-6281.dtsi.
The pinctrl seems to be the same.
These platforms differs only with their CPU, memory capabilities and the number of GPIO available (36 on 6192, 50 on 6281).
Quoted 7 lines
Quoted 5 lines
Signed-off-by Maxime Hadjinlian <[email protected]>--- arch/arm/boot/dts/kirkwood-6192.dtsi | 107 +++++++++++++++++++++++++++++++++++ 1 file changed, 107 insertions(+) create mode 100644 arch/arm/boot/dts/kirkwood-6192.dtsiHi Maxime
Hi Andrew
Quoted 3 lines
Jason recently sorted both 6181 and 6182. It would be nice if this file also used the same order. Take a look Jason's DT branch.
Sure thing, could you please give a link to Jason's branch ?
Quoted 3 lines
Thanks
Andrew