Skip to contentSkip to conversation

USB Host support for OMAP5 uEVM (for 3.14)

PATCH Superseded Roger Quadros 2 participants 12 messages Jan 20, 2014 – Jan 21, 2014

Subsystems (5)

v6 of 9 Superseded Latest is v9 →

lore
Share & tools
lore
#0 lore raw

v6 cover USB Host support for OMAP5 uEVM (for 3.14)

Hi Benoit & Tony,

This patchset brings up USB Host ports and Ethernet port on the OMAP5 uEVM board.

It depends on the TI Clock DT conversion patches [1] and is based on 3.13

[1] - http://article.gmane.org/gmane.linux.ports.arm.kernel/293147

Tested on:
- OMAP5 uEVM
- Pandaboard ES Rev. B1
- Beagleboard-XM Rev C2
- Beagleboard Rev C4.

cheers,
-roger

Changelog:

v6:
- Initialized clocks to -ENODEV and split patch 3.

v5:
- Expose all clocks in the DT binding document for mfd:omap-usb-host and mfd:omap-usb-tll

v4:
- Updated DT binding document for clock binding

v3:
- Rebased on top of 3.13-rc7

cheers,
-roger

Roger Quadros (10):
mfd: omap-usb-host: Use resource managed clk_get()
mfd: omap-usb-host: Get clocks based on hardware revision
mfd: omap-usb-host: Use clock names as per function for reference
clocks
mfd: omap-usb-host: Update DT clock binding information
mfd: omap-usb-tll: Update DT clock binding information
ARM: dts: omap4: Update omap-usb-host node
ARM: dts: omap5: Update omap-usb-host node
ARM: dts: omap4-panda: Provide USB PHY clock
ARM: dts: omap5-uevm: Provide USB PHY clock
ARM: OMAP2+: Remove legacy_init_ehci_clk()

 .../devicetree/bindings/mfd/omap-usb-host.txt      |  23 +++
 .../devicetree/bindings/mfd/omap-usb-tll.txt       |  10 ++
 arch/arm/boot/dts/omap4-panda-common.dtsi          |   8 +-
 arch/arm/boot/dts/omap4.dtsi                       |   6 +
 arch/arm/boot/dts/omap5-uevm.dts                   |   8 +-
 arch/arm/boot/dts/omap5.dtsi                       |   6 +
 arch/arm/mach-omap2/pdata-quirks.c                 |  16 --
 drivers/mfd/omap-usb-host.c                        | 171 ++++++++++-----------
 8 files changed, 128 insertions(+), 120 deletions(-)
Signature · 1 line
1.8.3.2
#1 lore raw

PATCH v6 1/10 mfd: omap-usb-host: Use resource managed clk_get()

Use devm_clk_get() instead of clk_get().

---
 drivers/mfd/omap-usb-host.c | 81 +++++++++------------------------------------
 1 file changed, 16 insertions(+), 65 deletions(-)
drivers/mfd/omap-usb-host.c +16 -65
index 142650f..1c9bca2 100644
@@ -674,46 +674,46 @@ static int usbhs_omap_probe(struct platform_device *pdev)
 
 	omap->ehci_logic_fck = ERR_PTR(-EINVAL);
 	if (need_logic_fck) {
-		omap->ehci_logic_fck = clk_get(dev, "ehci_logic_fck");
+		omap->ehci_logic_fck = devm_clk_get(dev, "ehci_logic_fck");
 		if (IS_ERR(omap->ehci_logic_fck)) {
 			ret = PTR_ERR(omap->ehci_logic_fck);
 			dev_dbg(dev, "ehci_logic_fck failed:%d\n", ret);
 		}
 	}
 
-	omap->utmi_p1_gfclk = clk_get(dev, "utmi_p1_gfclk");
+	omap->utmi_p1_gfclk = devm_clk_get(dev, "utmi_p1_gfclk");
 	if (IS_ERR(omap->utmi_p1_gfclk)) {
 		ret = PTR_ERR(omap->utmi_p1_gfclk);
 		dev_err(dev, "utmi_p1_gfclk failed error:%d\n", ret);
-		goto err_p1_gfclk;
+		goto err_mem;
 	}
 
-	omap->utmi_p2_gfclk = clk_get(dev, "utmi_p2_gfclk");
+	omap->utmi_p2_gfclk = devm_clk_get(dev, "utmi_p2_gfclk");
 	if (IS_ERR(omap->utmi_p2_gfclk)) {
 		ret = PTR_ERR(omap->utmi_p2_gfclk);
 		dev_err(dev, "utmi_p2_gfclk failed error:%d\n", ret);
-		goto err_p2_gfclk;
+		goto err_mem;
 	}
 
-	omap->xclk60mhsp1_ck = clk_get(dev, "xclk60mhsp1_ck");
+	omap->xclk60mhsp1_ck = devm_clk_get(dev, "xclk60mhsp1_ck");
 	if (IS_ERR(omap->xclk60mhsp1_ck)) {
 		ret = PTR_ERR(omap->xclk60mhsp1_ck);
 		dev_err(dev, "xclk60mhsp1_ck failed error:%d\n", ret);
-		goto err_xclk60mhsp1;
+		goto err_mem;
 	}
 
-	omap->xclk60mhsp2_ck = clk_get(dev, "xclk60mhsp2_ck");
+	omap->xclk60mhsp2_ck = devm_clk_get(dev, "xclk60mhsp2_ck");
 	if (IS_ERR(omap->xclk60mhsp2_ck)) {
 		ret = PTR_ERR(omap->xclk60mhsp2_ck);
 		dev_err(dev, "xclk60mhsp2_ck failed error:%d\n", ret);
-		goto err_xclk60mhsp2;
+		goto err_mem;
 	}
 
-	omap->init_60m_fclk = clk_get(dev, "init_60m_fclk");
+	omap->init_60m_fclk = devm_clk_get(dev, "init_60m_fclk");
 	if (IS_ERR(omap->init_60m_fclk)) {
 		ret = PTR_ERR(omap->init_60m_fclk);
 		dev_err(dev, "init_60m_fclk failed error:%d\n", ret);
-		goto err_init60m;
+		goto err_mem;
 	}
 
 	for (i = 0; i < omap->nports; i++) {
@@ -727,21 +727,21 @@ static int usbhs_omap_probe(struct platform_device *pdev)
 		 * platforms have all clocks and we can function without
 		 * them
 		 */
-		omap->utmi_clk[i] = clk_get(dev, clkname);
+		omap->utmi_clk[i] = devm_clk_get(dev, clkname);
 		if (IS_ERR(omap->utmi_clk[i]))
 			dev_dbg(dev, "Failed to get clock : %s : %ld\n",
 				clkname, PTR_ERR(omap->utmi_clk[i]));
 
 		snprintf(clkname, sizeof(clkname),
 				"usb_host_hs_hsic480m_p%d_clk", i + 1);
-		omap->hsic480m_clk[i] = clk_get(dev, clkname);
+		omap->hsic480m_clk[i] = devm_clk_get(dev, clkname);
 		if (IS_ERR(omap->hsic480m_clk[i]))
 			dev_dbg(dev, "Failed to get clock : %s : %ld\n",
 				clkname, PTR_ERR(omap->hsic480m_clk[i]));
 
 		snprintf(clkname, sizeof(clkname),
 				"usb_host_hs_hsic60m_p%d_clk", i + 1);
-		omap->hsic60m_clk[i] = clk_get(dev, clkname);
+		omap->hsic60m_clk[i] = devm_clk_get(dev, clkname);
 		if (IS_ERR(omap->hsic60m_clk[i]))
 			dev_dbg(dev, "Failed to get clock : %s : %ld\n",
 				clkname, PTR_ERR(omap->hsic60m_clk[i]));
@@ -784,7 +784,7 @@ static int usbhs_omap_probe(struct platform_device *pdev)
 
 		if (ret) {
 			dev_err(dev, "Failed to create DT children: %d\n", ret);
-			goto err_alloc;
+			goto err_mem;
 		}
 
 	} else {
@@ -792,40 +792,12 @@ static int usbhs_omap_probe(struct platform_device *pdev)
 		if (ret) {
 			dev_err(dev, "omap_usbhs_alloc_children failed: %d\n",
 						ret);
-			goto err_alloc;
+			goto err_mem;
 		}
 	}
 
 	return 0;
 
-err_alloc:
-	for (i = 0; i < omap->nports; i++) {
-		if (!IS_ERR(omap->utmi_clk[i]))
-			clk_put(omap->utmi_clk[i]);
-		if (!IS_ERR(omap->hsic60m_clk[i]))
-			clk_put(omap->hsic60m_clk[i]);
-		if (!IS_ERR(omap->hsic480m_clk[i]))
-			clk_put(omap->hsic480m_clk[i]);
-	}
-
-	clk_put(omap->init_60m_fclk);
-
-err_init60m:
-	clk_put(omap->xclk60mhsp2_ck);
-
-err_xclk60mhsp2:
-	clk_put(omap->xclk60mhsp1_ck);
-
-err_xclk60mhsp1:
-	clk_put(omap->utmi_p2_gfclk);
-
-err_p2_gfclk:
-	clk_put(omap->utmi_p1_gfclk);
-
-err_p1_gfclk:
-	if (!IS_ERR(omap->ehci_logic_fck))
-		clk_put(omap->ehci_logic_fck);
-
 err_mem:
 	pm_runtime_disable(dev);
 
@@ -847,27 +819,6 @@ static int usbhs_omap_remove_child(struct device *dev, void *data)
  */
 static int usbhs_omap_remove(struct platform_device *pdev)
 {
-	struct usbhs_hcd_omap *omap = platform_get_drvdata(pdev);
-	int i;
-
-	for (i = 0; i < omap->nports; i++) {
-		if (!IS_ERR(omap->utmi_clk[i]))
-			clk_put(omap->utmi_clk[i]);
-		if (!IS_ERR(omap->hsic60m_clk[i]))
-			clk_put(omap->hsic60m_clk[i]);
-		if (!IS_ERR(omap->hsic480m_clk[i]))
-			clk_put(omap->hsic480m_clk[i]);
-	}
-
-	clk_put(omap->init_60m_fclk);
-	clk_put(omap->utmi_p1_gfclk);
-	clk_put(omap->utmi_p2_gfclk);
-	clk_put(omap->xclk60mhsp2_ck);
-	clk_put(omap->xclk60mhsp1_ck);
-
-	if (!IS_ERR(omap->ehci_logic_fck))
-		clk_put(omap->ehci_logic_fck);
-
 	pm_runtime_disable(&pdev->dev);
 
 	/* remove children */
Signature · 1 line
1.8.3.2
#2 lore raw

PATCH v6 2/10 mfd: omap-usb-host: Get clocks based on hardware revision

In reply to Roger Quadros

Not all revisions have all the clocks so get the necessary clocks based on hardware revision.

This should avoid un-necessary clk_get failure messages that were observed earlier.

Be more strict and always fail on clk_get() error.

CC Lee Jones <[email protected]>
CC Samuel Ortiz <[email protected]>
---
 drivers/mfd/omap-usb-host.c | 92 +++++++++++++++++++++++++++++++--------------
 1 file changed, 64 insertions(+), 28 deletions(-)
drivers/mfd/omap-usb-host.c +64 -28
index 1c9bca2..eaafd2e 100644
@@ -665,22 +665,41 @@ static int usbhs_omap_probe(struct platform_device *pdev)
 		goto err_mem;
 	}
 
-	need_logic_fck = false;
+	/* Set all clocks as invalid to begin with */
+	omap->ehci_logic_fck = omap->init_60m_fclk = ERR_PTR(-ENODEV);
+	omap->utmi_p1_gfclk = omap->utmi_p2_gfclk = ERR_PTR(-ENODEV);
+	omap->xclk60mhsp1_ck = omap->xclk60mhsp2_ck = ERR_PTR(-ENODEV);
+
 	for (i = 0; i < omap->nports; i++) {
-		if (is_ehci_phy_mode(i) || is_ehci_tll_mode(i) ||
-			is_ehci_hsic_mode(i))
-				need_logic_fck |= true;
+		omap->utmi_clk[i] = ERR_PTR(-ENODEV);
+		omap->hsic480m_clk[i] = ERR_PTR(-ENODEV);
+		omap->hsic60m_clk[i] = ERR_PTR(-ENODEV);
 	}
 
-	omap->ehci_logic_fck = ERR_PTR(-EINVAL);
-	if (need_logic_fck) {
-		omap->ehci_logic_fck = devm_clk_get(dev, "ehci_logic_fck");
-		if (IS_ERR(omap->ehci_logic_fck)) {
-			ret = PTR_ERR(omap->ehci_logic_fck);
-			dev_dbg(dev, "ehci_logic_fck failed:%d\n", ret);
+	/* for OMAP3 i.e. USBHS REV1 */
+	if (omap->usbhs_rev == OMAP_USBHS_REV1) {
+		need_logic_fck = false;
+		for (i = 0; i < omap->nports; i++) {
+			if (is_ehci_phy_mode(pdata->port_mode[i]) ||
+			    is_ehci_tll_mode(pdata->port_mode[i]) ||
+			    is_ehci_hsic_mode(pdata->port_mode[i]))
+
+				need_logic_fck |= true;
+		}
+
+		if (need_logic_fck) {
+			omap->ehci_logic_fck = clk_get(dev, "usbhost_120m_fck");
+			if (IS_ERR(omap->ehci_logic_fck)) {
+				ret = PTR_ERR(omap->ehci_logic_fck);
+				dev_err(dev, "usbhost_120m_fck failed:%d\n",
+					ret);
+				goto err_mem;
+			}
 		}
+		goto initialize;
 	}
 
+	/* for OMAP4+ i.e. USBHS REV2+ */
 	omap->utmi_p1_gfclk = devm_clk_get(dev, "utmi_p1_gfclk");
 	if (IS_ERR(omap->utmi_p1_gfclk)) {
 		ret = PTR_ERR(omap->utmi_p1_gfclk);
@@ -728,54 +747,71 @@ static int usbhs_omap_probe(struct platform_device *pdev)
 		 * them
 		 */
 		omap->utmi_clk[i] = devm_clk_get(dev, clkname);
-		if (IS_ERR(omap->utmi_clk[i]))
-			dev_dbg(dev, "Failed to get clock : %s : %ld\n",
-				clkname, PTR_ERR(omap->utmi_clk[i]));
+		if (IS_ERR(omap->utmi_clk[i])) {
+			ret = PTR_ERR(omap->utmi_clk[i]);
+			dev_err(dev, "Failed to get clock : %s : %d\n",
+				clkname, ret);
+			goto err_mem;
+		}
 
 		snprintf(clkname, sizeof(clkname),
 				"usb_host_hs_hsic480m_p%d_clk", i + 1);
 		omap->hsic480m_clk[i] = devm_clk_get(dev, clkname);
-		if (IS_ERR(omap->hsic480m_clk[i]))
-			dev_dbg(dev, "Failed to get clock : %s : %ld\n",
-				clkname, PTR_ERR(omap->hsic480m_clk[i]));
+		if (IS_ERR(omap->hsic480m_clk[i])) {
+			ret = PTR_ERR(omap->hsic480m_clk[i]);
+			dev_err(dev, "Failed to get clock : %s : %d\n",
+				clkname, ret);
+			goto err_mem;
+		}
 
 		snprintf(clkname, sizeof(clkname),
 				"usb_host_hs_hsic60m_p%d_clk", i + 1);
 		omap->hsic60m_clk[i] = devm_clk_get(dev, clkname);
-		if (IS_ERR(omap->hsic60m_clk[i]))
-			dev_dbg(dev, "Failed to get clock : %s : %ld\n",
-				clkname, PTR_ERR(omap->hsic60m_clk[i]));
+		if (IS_ERR(omap->hsic60m_clk[i])) {
+			ret = PTR_ERR(omap->hsic60m_clk[i]);
+			dev_err(dev, "Failed to get clock : %s : %d\n",
+				clkname, ret);
+			goto err_mem;
+		}
 	}
 
 	if (is_ehci_phy_mode(pdata->port_mode[0])) {
-		/* for OMAP3, clk_set_parent fails */
 		ret = clk_set_parent(omap->utmi_p1_gfclk,
 					omap->xclk60mhsp1_ck);
-		if (ret != 0)
-			dev_dbg(dev, "xclk60mhsp1_ck set parent failed: %d\n",
+		if (ret != 0) {
+			dev_err(dev, "xclk60mhsp1_ck set parent failed: %d\n",
 					ret);
+			goto err_mem;
+		}
 	} else if (is_ehci_tll_mode(pdata->port_mode[0])) {
 		ret = clk_set_parent(omap->utmi_p1_gfclk,
 					omap->init_60m_fclk);
-		if (ret != 0)
-			dev_dbg(dev, "P0 init_60m_fclk set parent failed: %d\n",
+		if (ret != 0) {
+			dev_err(dev, "P0 init_60m_fclk set parent failed: %d\n",
 					ret);
+			goto err_mem;
+		}
 	}
 
 	if (is_ehci_phy_mode(pdata->port_mode[1])) {
 		ret = clk_set_parent(omap->utmi_p2_gfclk,
 					omap->xclk60mhsp2_ck);
-		if (ret != 0)
-			dev_dbg(dev, "xclk60mhsp2_ck set parent failed: %d\n",
+		if (ret != 0) {
+			dev_err(dev, "xclk60mhsp2_ck set parent failed: %d\n",
 					ret);
+			goto err_mem;
+		}
 	} else if (is_ehci_tll_mode(pdata->port_mode[1])) {
 		ret = clk_set_parent(omap->utmi_p2_gfclk,
 						omap->init_60m_fclk);
-		if (ret != 0)
-			dev_dbg(dev, "P1 init_60m_fclk set parent failed: %d\n",
+		if (ret != 0) {
+			dev_err(dev, "P1 init_60m_fclk set parent failed: %d\n",
 					ret);
+			goto err_mem;
+		}
 	}
 
+initialize:
 	omap_usbhs_init(dev);
 
 	if (dev->of_node) {
Signature · 1 line
1.8.3.2
#3 lore raw

PATCH v6 3/10 mfd: omap-usb-host: Use clock names as per function for reference clocks

In reply to Roger Quadros

Use a meaningful name for the reference clocks so that it indicates the function.

CC Lee Jones <[email protected]>
CC Samuel Ortiz <[email protected]>
---
 drivers/mfd/omap-usb-host.c | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)
drivers/mfd/omap-usb-host.c +3 -3
index eaafd2e..d6fab3e 100644
@@ -714,21 +714,21 @@ static int usbhs_omap_probe(struct platform_device *pdev)
 		goto err_mem;
 	}
 
-	omap->xclk60mhsp1_ck = devm_clk_get(dev, "xclk60mhsp1_ck");
+	omap->xclk60mhsp1_ck = devm_clk_get(dev, "refclk_60m_ext_p1");
 	if (IS_ERR(omap->xclk60mhsp1_ck)) {
 		ret = PTR_ERR(omap->xclk60mhsp1_ck);
 		dev_err(dev, "xclk60mhsp1_ck failed error:%d\n", ret);
 		goto err_mem;
 	}
 
-	omap->xclk60mhsp2_ck = devm_clk_get(dev, "xclk60mhsp2_ck");
+	omap->xclk60mhsp2_ck = devm_clk_get(dev, "refclk_60m_ext_p2");
 	if (IS_ERR(omap->xclk60mhsp2_ck)) {
 		ret = PTR_ERR(omap->xclk60mhsp2_ck);
 		dev_err(dev, "xclk60mhsp2_ck failed error:%d\n", ret);
 		goto err_mem;
 	}
 
-	omap->init_60m_fclk = devm_clk_get(dev, "init_60m_fclk");
+	omap->init_60m_fclk = devm_clk_get(dev, "refclk_60m_int");
 	if (IS_ERR(omap->init_60m_fclk)) {
 		ret = PTR_ERR(omap->init_60m_fclk);
 		dev_err(dev, "init_60m_fclk failed error:%d\n", ret);
Signature · 1 line
1.8.3.2
#4 lore raw

PATCH v6 4/10 mfd: omap-usb-host: Update DT clock binding information

In reply to Roger Quadros

The omap-usb-host driver expects certained named clocks. Add this information to the DT binding document.

CC Lee Jones <[email protected]>
CC Samuel Ortiz <[email protected]>
---
 .../devicetree/bindings/mfd/omap-usb-host.txt      | 23 ++++++++++++++++++++++
 1 file changed, 23 insertions(+)
Documentation/devicetree/bindings/mfd/omap-usb-host.txt +23 -0
index b381fa6..4721b2d 100644
@@ -32,6 +32,29 @@ Optional properties:
 - single-ulpi-bypass: Must be present if the controller contains a single
   ULPI bypass control bit. e.g. OMAP3 silicon <= ES2.1
 
+- clocks: a list of phandles and clock-specifier pairs, one for each entry in
+  clock-names.
+
+- clock-names: should include:
+  For OMAP3
+  * "usbhost_120m_fck" - 120MHz Functional clock.
+
+  For OMAP4+
+  * "refclk_60m_int" - 60MHz internal reference clock for UTMI clock mux
+  * "refclk_60m_ext_p1" - 60MHz external ref. clock for Port 1's UTMI clock mux.
+  * "refclk_60m_ext_p2" - 60MHz external ref. clock for Port 2's UTMI clock mux
+  * "utmi_p1_gfclk" - Port 1 UTMI clock mux.
+  * "utmi_p2_gfclk" - Port 2 UTMI clock mux.
+  * "usb_host_hs_utmi_p1_clk" - Port 1 UTMI clock gate.
+  * "usb_host_hs_utmi_p2_clk" - Port 2 UTMI clock gate.
+  * "usb_host_hs_utmi_p3_clk" - Port 3 UTMI clock gate.
+  * "usb_host_hs_hsic480m_p1_clk" - Port 1 480MHz HSIC clock gate.
+  * "usb_host_hs_hsic480m_p2_clk" - Port 2 480MHz HSIC clock gate.
+  * "usb_host_hs_hsic480m_p3_clk" - Port 3 480MHz HSIC clock gate.
+  * "usb_host_hs_hsic60m_p1_clk" - Port 1 60MHz HSIC clock gate.
+  * "usb_host_hs_hsic60m_p2_clk" - Port 2 60MHz HSIC clock gate.
+  * "usb_host_hs_hsic60m_p3_clk" - Port 3 60MHz HSIC clock gate.
+
 Required properties if child node exists:
 
 - #address-cells: Must be 1
Signature · 1 line
1.8.3.2
#5 lore raw

PATCH v6 5/10 mfd: omap-usb-tll: Update DT clock binding information

In reply to Roger Quadros

The omap-usb-tll driver needs one clock for each TLL channel. Add this information to the DT binding document.

CC Lee Jones <[email protected]>
CC Samuel Ortiz <[email protected]>
---
 Documentation/devicetree/bindings/mfd/omap-usb-tll.txt | 10 ++++++++++
 1 file changed, 10 insertions(+)
Documentation/devicetree/bindings/mfd/omap-usb-tll.txt +10 -0
index 62fe697..c58d704 100644
@@ -7,6 +7,16 @@ Required properties:
 - interrupts : should contain the TLL module's interrupt
 - ti,hwmod : must contain "usb_tll_hs"
 
+Optional properties:
+
+- clocks: a list of phandles and clock-specifier pairs, one for each entry in
+  clock-names.
+
+- clock-names: should include:
+  * "usb_tll_hs_usb_ch0_clk" - USB TLL channel 0 clock
+  * "usb_tll_hs_usb_ch1_clk" - USB TLL channel 1 clock
+  * "usb_tll_hs_usb_ch2_clk" - USB TLL channel 2 clock
+
 Example:
 
 	usbhstll: usbhstll at 4a062000 {
Signature · 1 line
1.8.3.2
#6 lore raw

PATCH v6 6/10 ARM: dts: omap4: Update omap-usb-host node

In reply to Roger Quadros

The omap-usb-host driver expects a certain name for internal and external reference clocks. Provide these clocks.

---
 arch/arm/boot/dts/omap4.dtsi | 6 ++++++
 1 file changed, 6 insertions(+)
arch/arm/boot/dts/omap4.dtsi +6 -0
index d3f8a6e..39a05ce 100644
@@ -697,6 +697,12 @@
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges;
+			clocks = <&init_60m_fclk>,
+				 <&xclk60mhsp1_ck>,
+				 <&xclk60mhsp2_ck>;
+			clock-names = "refclk_60m_int",
+				      "refclk_60m_ext_p1",
+				      "refclk_60m_ext_p2";
 
 			usbhsohci: ohci at 4a064800 {
 				compatible = "ti,ohci-omap3", "usb-ohci";
Signature · 1 line
1.8.3.2
#7 lore raw

PATCH v6 7/10 ARM: dts: omap5: Update omap-usb-host node

In reply to Roger Quadros

The omap-usb-host driver expects a certain name for internal and external reference clocks. Provide these clocks.

---
 arch/arm/boot/dts/omap5.dtsi | 6 ++++++
 1 file changed, 6 insertions(+)
arch/arm/boot/dts/omap5.dtsi +6 -0
index 2f12a47..0f82ecf 100644
@@ -765,6 +765,12 @@
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges;
+			clocks = <&l3init_60m_fclk>,
+				 <&xclk60mhsp1_ck>,
+				 <&xclk60mhsp2_ck>;
+			clock-names = "refclk_60m_int",
+				      "refclk_60m_ext_p1",
+				      "refclk_60m_ext_p2";
 
 			usbhsohci: ohci at 4a064800 {
 				compatible = "ti,ohci-omap3", "usb-ohci";
Signature · 1 line
1.8.3.2
#8 lore raw

PATCH v6 8/10 ARM: dts: omap4-panda: Provide USB PHY clock

In reply to Roger Quadros

The USB PHY gets its clock from AUXCLK3. Provide this information.

---
 arch/arm/boot/dts/omap4-panda-common.dtsi | 8 ++------
 1 file changed, 2 insertions(+), 6 deletions(-)
arch/arm/boot/dts/omap4-panda-common.dtsi +2 -6
index 88c6a05..50b72966 100644
@@ -83,12 +83,8 @@
 		compatible = "usb-nop-xceiv";
 		reset-gpios = <&gpio2 30 GPIO_ACTIVE_LOW>;   /* gpio_62 */
 		vcc-supply = <&hsusb1_power>;
-	/**
-	 * FIXME:
-	 * put the right clock phandle here when available
-	 *	clocks = <&auxclk3>;
-	 *	clock-names = "main_clk";
-	 */
+		clocks = <&auxclk3_ck>;
+		clock-names = "main_clk";
 		clock-frequency = <19200000>;
 	};
 
Signature · 1 line
1.8.3.2
#9 lore raw

PATCH v6 9/10 ARM: dts: omap5-uevm: Provide USB PHY clock

In reply to Roger Quadros

The HS USB 2 PHY gets its clock from AUXCLK1. Provide this information.

---
 arch/arm/boot/dts/omap5-uevm.dts | 8 ++------
 1 file changed, 2 insertions(+), 6 deletions(-)
arch/arm/boot/dts/omap5-uevm.dts +2 -6
index 002fa70..3b99ec2 100644
@@ -31,12 +31,8 @@
 	hsusb2_phy: hsusb2_phy {
 		compatible = "usb-nop-xceiv";
 		reset-gpios = <&gpio3 16 GPIO_ACTIVE_LOW>; /* gpio3_80 HUB_NRESET */
-	/**
-	  * FIXME
-	  * Put the right clock phandle here when available
-	  *	clocks = <&auxclk1>;
-	  *	clock-names = "main_clk";
-	  */
+		clocks = <&auxclk1_ck>;
+		clock-names = "main_clk";
 		clock-frequency = <19200000>;
 	};
 
Signature · 1 line
1.8.3.2
#10 lore raw

PATCH v6 10/10 ARM: OMAP2+: Remove legacy_init_ehci_clk()

In reply to Roger Quadros

The necessary clock phandle for the EHCI clock is now provided via device tree so we no longer need this legacy method.

---
 arch/arm/mach-omap2/pdata-quirks.c | 16 ----------------
 1 file changed, 16 deletions(-)
arch/arm/mach-omap2/pdata-quirks.c +0 -16
index 39f020c..6a4e2d1 100644
@@ -26,20 +26,6 @@ struct pdata_init {
 	void (*fn)(void);
 };
 
-/*
- * Create alias for USB host PHY clock.
- * Remove this when clock phandle can be provided via DT
- */
-static void __init __used legacy_init_ehci_clk(char *clkname)
-{
-	int ret;
-
-	ret = clk_add_alias("main_clk", NULL, clkname, NULL);
-	if (ret)
-		pr_err("%s:Failed to add main_clk alias to %s :%d\n",
-		       __func__, clkname, ret);
-}
-
 #if IS_ENABLED(CONFIG_WL12XX)
 
 static struct wl12xx_platform_data wl12xx __initdata;
@@ -105,7 +91,6 @@ static void __init omap4_sdp_legacy_init(void)
 static void __init omap4_panda_legacy_init(void)
 {
 	omap4_panda_display_init_of();
-	legacy_init_ehci_clk("auxclk3_ck");
 	legacy_init_wl12xx(WL12XX_REFCLOCK_38, 0, 53);
 }
 #endif
@@ -113,7 +98,6 @@ static void __init omap4_panda_legacy_init(void)
 #ifdef CONFIG_SOC_OMAP5
 static void __init omap5_uevm_legacy_init(void)
 {
-	legacy_init_ehci_clk("auxclk1_ck");
 }
 #endif
 
Signature · 1 line
1.8.3.2
#11 lore raw
In reply to Roger Quadros
Quoted 2 lines

This patchset brings up USB Host ports and Ethernet port on the OMAP5 uEVM board.

I'd keep hold of this and send it out again when the merge-window is closed.

Signature · 4 lines
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org ? Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog