pinctrl: single: add low powr mode support
Subsystems (3)
PATCH 1/1 pinctrl: single: add low powr mode support
From: Chao Xie <[email protected]>
For some silicons, the pin configuration register can control the output of the pin when the pad including the pin enter low power mode.
For example, the pin can be "Drive 1", "Drive 0", "Float" when the pad including the pin enter low power mode.
It is very useful when you want to control the power leakeage when the SOC enter low power mode, and can save more power for the low power mode.
--- Documentation/devicetree/bindings/pinctrl/pinctrl-single.txt | 7 +++++++ drivers/pinctrl/pinctrl-single.c | 3 +++ 2 files changed, 10 insertions(+)
Documentation/devicetree/bindings/pinctrl/pinctrl-single.txt +7 -0
@@ -63,6 +63,13 @@ Optional properties: /* input, enable bits, disable bits, mask */ pinctrl-single,input-schmitt-enable = <0x30 0x40 0 0x70>; +- pinctrl-single,low-power-mode : array of value that are used to configure + low power mode of this pin. For some silicons, the low power mode will + control the output of the pin when the pad including the pin enter low + power mode. + /* low power mode value, mask */ + pinctrl-single,low-power-mode = <0x288 0x388>; + - pinctrl-single,gpio-range : list of value that are used to configure a GPIO range. They're value of subnode phandle, pin base in pinctrl device, pin number in this range, GPIO function value of this GPIO range.
drivers/pinctrl/pinctrl-single.c +3 -0
@@ -661,6 +661,7 @@ static int pcs_pinconf_get(struct pinctrl_dev *pctldev,break ;case PIN_CONFIG_DRIVE_STRENGTH :case PIN_CONFIG_SLEW_RATE : +case PIN_CONFIG_LOW_POWER_MODE :default : *config = data;break ;
@@ -698,6 +699,7 @@ static int pcs_pinconf_set(struct pinctrl_dev *pctldev,case PIN_CONFIG_INPUT_SCHMITT :case PIN_CONFIG_DRIVE_STRENGTH :case PIN_CONFIG_SLEW_RATE : +case PIN_CONFIG_LOW_POWER_MODE : shift =ffs (func->conf[i].mask) -1 ; data &= ~func->conf[i].mask; data |= (arg << shift) & func->conf[i].mask;
@@ -1100,6 +1102,7 @@ static int pcs_parse_pinconf(struct pcs_device *pcs, struct device_node *np, { "pinctrl-single,drive-strength", PIN_CONFIG_DRIVE_STRENGTH, }, { "pinctrl-single,slew-rate", PIN_CONFIG_SLEW_RATE, }, { "pinctrl-single,input-schmitt", PIN_CONFIG_INPUT_SCHMITT, }, + { "pinctrl-single,low-power-mode", PIN_CONFIG_LOW_POWER_MODE, }, };struct pcs_conf_type prop4[] = { { "pinctrl-single,bias-pullup", PIN_CONFIG_BIAS_PULL_UP, },
Signature · 1 line
1.8.3.2
PATCH 1/1 pinctrl: single: add low powr mode support
Quoted 11 lines · Chao Xie
From: Chao Xie <[email protected]>
For some silicons, the pin configuration register can control the output of the pin when the pad including the pin enter low power mode.
For example, the pin can be "Drive 1", "Drive 0", "Float" when the pad including the pin enter low power mode.
It is very useful when you want to control the power leakeage when the SOC enter low power mode, and can save more power for the low power mode.
Quoted 1 line
Signed-off-by Chao Xie <[email protected]>
Looks similar to the other pin config stuff, patch applied unless Tony protests.
Yours,
Linus Walleij
Tony Lindgren
maintainerPATCH 1/1 pinctrl: single: add low powr mode support
Quoted 13 lines · Linus Walleij
Quoted 11 lines · Chao Xie
From: Chao Xie <[email protected]>
For some silicons, the pin configuration register can control the output of the pin when the pad including the pin enter low power mode.
For example, the pin can be "Drive 1", "Drive 0", "Float" when the pad including the pin enter low power mode.
It is very useful when you want to control the power leakeage when the SOC enter low power mode, and can save more power for the low power mode.
Quoted 4 lines
Quoted 1 line
Signed-off-by Chao Xie <[email protected]>Looks similar to the other pin config stuff, patch applied unless Tony protests.
Seems fine to me: