Move DT kirkwood into mach-mvebu
Subsystems (14)
Andrew Lunn
maintainerv2 cover Move DT kirkwood into mach-mvebu
The process of making most kirkwood boards boot using DT is nearly complete. We can now move these boards into mach-mvebu, freeing them of the legacy code needed for none-DT systems. At the same time, they can become part of ARCH_MULTI_V5.
Since v1:mv88f6281gtw_ge switch really does now use DT.
The L2 Cache binding has been re-written. kirkwood.dtsi changes have been placed into there own patch. Added mvebu_v5_defconfig
Fixed a few typos in changelogs
Added a few Cc:s
Andrew Lunn (23):
ARM: Kirkwood: Give pm.c its own header file.
IRQ: Orion: Fix getting generic chip pointer.
ARM: Kirkwood: Convert mv88f6281gtw_ge switch setup to DT
ARM: Kirkwood: Drop printing the SoC type and revision
ARM: Kirkwood: Seperate board-dt from common and pcie code.
ARM: Kirkwood: ioremap the cpu_config register before using it.
ARM: Kirkwood: ioremap memory control register
ARM: MVEBU: Add ARCH_MULTI_V7 to SoCs
ARM: Orion: Move cache-feroceon-l2.h out of plat-orion
ARM: MM: Add DT binding for Feroceon L2 cache
ARM: Kirkwood: Instantiate L2 cache from DT.
ARM: Fix default CPU selection for ARCH_MULTI_V5
ARM: Fix MULTI_TLB for feroceon
ARM: MM Enable building Feroceon L2 cache controller with ARCH_MVEBU
ARM: Move kirkwood DT boards into mach-mvebu
ARM: MVEBU: Let kirkwood use the system controller for restart
ARM: MVEBU: Instantiate system controller in kirkwood.dtsi
drivers: Enable building of Kirkwood drivers for mach-mvebu
ARM: MVEBU: Enable mvebu-soc-id on Kirkwood
ARM: config: Add a multi_v5_defconfig
ARM: MVEBU: Simplifiy headers and make local
ARM: config: Add mvebu_v5_defconfig
ARM: Kirkwood: Remove DT support
.../devicetree/bindings/arm/mrvl/feroceon.txt | 17 ++ arch/arm/Kconfig | 2 +- arch/arm/boot/dts/Makefile | 34 ++-- arch/arm/boot/dts/kirkwood-mv88f6281gtw-ge.dts | 62 +++++++ arch/arm/boot/dts/kirkwood.dtsi | 10 ++ arch/arm/configs/kirkwood_defconfig | 6 - arch/arm/configs/multi_v5_defconfig | 183 ++++++++++++++++++++ arch/arm/configs/mvebu_v5_defconfig | 166 ++++++++++++++++++ arch/arm/include/asm/hardware/cache-feroceon-l2.h | 13 ++ arch/arm/mach-kirkwood/Kconfig | 25 --- arch/arm/mach-kirkwood/Makefile | 6 +- arch/arm/mach-kirkwood/board-dt.c | 150 ---------------- arch/arm/mach-kirkwood/board-mv88f6281gtw_ge.c | 50 ------ arch/arm/mach-kirkwood/common.c | 3 +- arch/arm/mach-kirkwood/common.h | 13 -- arch/arm/mach-kirkwood/include/mach/bridge-regs.h | 2 + arch/arm/mach-kirkwood/pm.c | 9 +- arch/arm/mach-kirkwood/pm.h | 26 +++ arch/arm/mach-mv78xx0/common.c | 2 +- arch/arm/mach-mvebu/Kconfig | 28 ++- arch/arm/mach-mvebu/Makefile | 1 + arch/arm/mach-mvebu/kirkwood-pm.c | 76 +++++++++ arch/arm/mach-mvebu/kirkwood-pm.h | 26 +++ arch/arm/mach-mvebu/kirkwood.c | 189 +++++++++++++++++++++ arch/arm/mach-mvebu/kirkwood.h | 22 +++ arch/arm/mach-mvebu/mvebu-soc-id.c | 1 + arch/arm/mm/Kconfig | 2 +- arch/arm/mm/cache-feroceon-l2.c | 54 +++++- arch/arm/mm/proc-feroceon.S | 2 +- arch/arm/mm/tlb-v4wbi.S | 3 + .../plat-orion/include/plat/cache-feroceon-l2.h | 11 -- drivers/cpufreq/Kconfig.arm | 2 +- drivers/cpuidle/Kconfig.arm | 2 +- drivers/irqchip/irq-orion.c | 3 +- drivers/leds/Kconfig | 4 +- drivers/phy/Kconfig | 2 +- drivers/thermal/Kconfig | 2 +- sound/soc/kirkwood/Kconfig | 2 +- 38 files changed, 914 insertions(+), 297 deletions(-) create mode 100644 Documentation/devicetree/bindings/arm/mrvl/feroceon.txt create mode 100644 arch/arm/configs/multi_v5_defconfig create mode 100644 arch/arm/configs/mvebu_v5_defconfig create mode 100644 arch/arm/include/asm/hardware/cache-feroceon-l2.h delete mode 100644 arch/arm/mach-kirkwood/board-dt.c delete mode 100644 arch/arm/mach-kirkwood/board-mv88f6281gtw_ge.c create mode 100644 arch/arm/mach-kirkwood/pm.h create mode 100644 arch/arm/mach-mvebu/kirkwood-pm.c create mode 100644 arch/arm/mach-mvebu/kirkwood-pm.h create mode 100644 arch/arm/mach-mvebu/kirkwood.c create mode 100644 arch/arm/mach-mvebu/kirkwood.h delete mode 100644 arch/arm/plat-orion/include/plat/cache-feroceon-l2.h
Signature · 1 line
1.8.5.3
Andrew Lunn
maintainerPATCH v2 1/23 ARM: Kirkwood: Give pm.c its own header file.
The pm code needs to be seperated from common.h in order to split DT and non-DT systems apart. Move the declarations into a header file of its own and include it where needed.
--- arch/arm/mach-kirkwood/board-dt.c | 1 + arch/arm/mach-kirkwood/common.c | 1 + arch/arm/mach-kirkwood/common.h | 6 ------ arch/arm/mach-kirkwood/pm.h | 26 ++++++++++++++++++++++++++ 4 files changed, 28 insertions(+), 6 deletions(-) create mode 100644 arch/arm/mach-kirkwood/pm.h
arch/arm/mach-kirkwood/board-dt.c +1 -0
@@ -24,6 +24,7 @@#include <mach/bridge-regs.h> #include <plat/common.h> #include "common.h" +#include "pm.h" #define MV643XX_ETH_MAC_ADDR_LOW 0x0414#define MV643XX_ETH_MAC_ADDR_HIGH 0x0418
arch/arm/mach-kirkwood/common.c +1 -0
@@ -36,6 +36,7 @@#include <plat/time.h> #include <linux/platform_data/dma-mv_xor.h> #include "common.h" +#include "pm.h" /* These can go away once Kirkwood uses the mvebu-mbus DT binding */ #define KIRKWOOD_MBUS_NAND_TARGET 0x01
arch/arm/mach-kirkwood/common.h +0 -6
@@ -58,12 +58,6 @@ void kirkwood_cpufreq_init(void);void kirkwood_restart (enum reboot_mode ,const char *);void kirkwood_clk_init (void ); -#ifdef CONFIG_PM -void kirkwood_pm_init (void ); -#else -static inline void kirkwood_pm_init (void ) {}; -#endif -/* board init functions for boards not fully converted to fdt */ #ifdef CONFIG_MACH_MV88F6281GTW_GE_DT void mv88f6281gtw_ge_init (void );
arch/arm/mach-kirkwood/pm.h new file +26 -0
@@ -0,0 +1,26 @@ +/* +* Power Management driver for Marvell Kirkwood SoCs +* +* Copyright (C) 2013 Ezequiel Garcia <[email protected]> +* Copyright (C) 2010 Simon Guinot <[email protected]> +* +* This program is free software; you can redistribute it and/or modify +* it under the terms of the GNU General Public License, +* version 2 of the License. +* +* This program is distributed in the hope that it will be useful, +* but WITHOUT ANY WARRANTY; without even the implied warranty of +* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +* GNU General Public License for more details. +*/ + +#ifndef __ARCH_KIRKWOOD_PM_H +#define __ARCH_KIRKWOOD_PM_H + +#ifdef CONFIG_PM +void kirkwood_pm_init (void ); +#else +static inline void kirkwood_pm_init (void ) {}; +#endif + +#endif
Signature · 1 line
1.8.5.3
PATCH v2 1/23 ARM: Kirkwood: Give pm.c its own header file.
Quoted 4 lines · Andrew Lunn
The pm code needs to be seperated from
common.hin order to split DT and non-DT systems apart. Move the declarations into a header file of its own and include it where needed.
s/seperated/separated
Other than that:
Signature · 3 lines
Ezequiel Garc?a, Free Electrons Embedded Linux, Kernel and Android Engineering http://free-electrons.com
Andrew Lunn
maintainerPATCH v2 2/23 IRQ: Orion: Fix getting generic chip pointer.
In reply to Andrew LunnEnabling SPARSE_IRQ shows up a bug in the irq-orion bridge interrupt handler. The bridge interrupt is implemented using a single generic chip. Thus the parameter passed to irq_get_domain_generic_chip() should always be zero.
--- drivers/irqchip/irq-orion.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-)
drivers/irqchip/irq-orion.c +2 -1
@@ -111,7 +111,8 @@ IRQCHIP_DECLARE(orion_intc, "marvell,orion-intc", orion_irq_init);static void orion_bridge_irq_handler (unsigned int irq,struct irq_desc *desc) {struct irq_domain *d =irq_get_handler_data (irq); -struct irq_chip_generic *gc =irq_get_domain_generic_chip (d, irq); + +struct irq_chip_generic *gc =irq_get_domain_generic_chip (d,0 );u32 stat =readl_relaxed (gc->reg_base +ORION_BRIDGE_IRQ_CAUSE ) & gc->mask_cache;
Signature · 1 line
1.8.5.3
Andrew Lunn
maintainerPATCH v2 3/23 ARM: Kirkwood: Convert mv88f6281gtw_ge switch setup to DT
In reply to Andrew LunnThe mv88f6281gtw_ge has a ethernet switch connected to the ethernet port of the SoC. Convert the platform device instantiation to a DT instantiation.
---
v2
Remove the spurius Module.symvers
Really do describe the switch in DT.
--- arch/arm/boot/dts/kirkwood-mv88f6281gtw-ge.dts | 62 ++++++++++++++++++++++++++ arch/arm/mach-kirkwood/Kconfig | 7 --- arch/arm/mach-kirkwood/Makefile | 1 - arch/arm/mach-kirkwood/board-dt.c | 3 -- arch/arm/mach-kirkwood/board-mv88f6281gtw_ge.c | 50 --------------------- arch/arm/mach-kirkwood/common.h | 7 --- 6 files changed, 62 insertions(+), 68 deletions(-) delete mode 100644 arch/arm/mach-kirkwood/board-mv88f6281gtw_ge.c
arch/arm/boot/dts/kirkwood-mv88f6281gtw-ge.dts +62 -0
@@ -122,4 +122,66 @@ gpios = <&gpio1 14 GPIO_ACTIVE_LOW>; }; }; + + dsa at 0 { + compatible = "marvell,dsa"; + #address-cells = <2>; + #size-cells = <0>; + + dsa,ethernet = <ð0>; + dsa,mii-bus = <ðphy0>; + + switch at 0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0 0>; /* MDIO address 0, switch 0 in tree */ + + port at 0 { + reg = <0>; + label = "lan1"; + }; + + port at 1 { + reg = <1>; + label = "lan2"; + }; + + port at 2 { + reg = <2>; + label = "lan3"; + }; + + port at 3 { + reg = <3>; + label = "lan4"; + }; + + port at 4 { + reg = <4>; + label = "wan"; + }; + + port at 5 { + reg = <5>; + label = "cpu"; + }; + }; + }; +}; + +&mdio { + status = "okay"; + + ethphy0: ethernet-phy at ff { + reg = <0xff>; /* No phy attached */ + speed = <1000>; + duplex = <1>; + }; +}; + +ð0 { + status = "okay"; + ethernet0-port at 0 { + phy-handle = <ðphy0>; + }; };
arch/arm/mach-kirkwood/Kconfig +0 -7
@@ -106,13 +106,6 @@ config ARCH_KIRKWOOD_DT Say 'Y' here if you want your kernel to support the Marvell Kirkwood using flattened device tree. -config MACH_MV88F6281GTW_GE_DT - bool "Marvell 88F6281 GTW GE Board (Flattened Device Tree)" - depends on ARCH_KIRKWOOD_DT - help - Say 'Y' here if you want your kernel to support the - Marvell 88F6281 GTW GE Board (Flattened Device Tree). - endmenu endif
arch/arm/mach-kirkwood/Makefile +0 -1
@@ -13,4 +13,3 @@ obj-$(CONFIG_MACH_TS219) += ts219-setup.o tsx1x-common.o obj-$(CONFIG_MACH_TS41X) += ts41x-setup.o tsx1x-common.o obj-$(CONFIG_ARCH_KIRKWOOD_DT) += board-dt.o -obj-$(CONFIG_MACH_MV88F6281GTW_GE_DT) += board-mv88f6281gtw_ge.o
arch/arm/mach-kirkwood/board-dt.c +0 -3
@@ -131,9 +131,6 @@ static void __init kirkwood_dt_init(void) kexec_reinit = kirkwood_enable_pcie;#endif -if (of_machine_is_compatible ("marvell,mv88f6281gtw-ge" )) -mv88f6281gtw_ge_init (); -of_platform_populate (NULL , of_default_bus_match_table,NULL ,NULL ); }
arch/arm/mach-kirkwood/board-mv88f6281gtw_ge.c deleted +0 -50
50 lines not on this page · raw message
arch/arm/mach-kirkwood/common.h +0 -7
@@ -58,13 +58,6 @@ void kirkwood_cpufreq_init(void);void kirkwood_restart (enum reboot_mode ,const char *);void kirkwood_clk_init (void ); -/* board init functions for boards not fully converted to fdt */ -#ifdef CONFIG_MACH_MV88F6281GTW_GE_DT -void mv88f6281gtw_ge_init (void ); -#else -static inline void mv88f6281gtw_ge_init (void ) {}; -#endif -/* early init functions not converted to fdt yet */ char *kirkwood_id (void );void kirkwood_l2_init (void );
Signature · 1 line
1.8.5.3
Andrew Lunn
maintainerPATCH v2 4/23 ARM: Kirkwood: Drop printing the SoC type and revision
In reply to Andrew LunnThis will be added back using the mach-mvebu equivelent once the move has been made.
--- arch/arm/mach-kirkwood/board-dt.c | 2 -- 1 file changed, 2 deletions(-)
arch/arm/mach-kirkwood/board-dt.c +0 -2
@@ -107,8 +107,6 @@ eth_fixup_skip:static void __init kirkwood_dt_init (void ) { -pr_info ("Kirkwood: %s.\n" ,kirkwood_id ()); -/* * Disable propagation of mbus errors to the CPU local bus, * as this causes mbus errors (which can occur for example
Signature · 1 line
1.8.5.3
PATCH v2 4/23 ARM: Kirkwood: Drop printing the SoC type and revision
Quoted 3 lines · Andrew Lunn
This will be added back using the mach-mvebu equivelent once the move has been made.
Minor typo: s/equivelent/equivalent
Signature · 3 lines
Ezequiel Garc?a, Free Electrons Embedded Linux, Kernel and Android Engineering http://free-electrons.com
Andrew Lunn
maintainerPATCH v2 5/23 ARM: Kirkwood: Seperate board-dt from common and pcie code.
In reply to Andrew LunnIn order to be able to move DT support into mach-mvebu, the DT code needs to be cleanly separated from common and pcie code. Import the needed bits of these files into board-dt.c. The "common" code then becomes purely legacy, supporting none DT boards, so reflect this in the Makefile targets.
--- arch/arm/mach-kirkwood/Makefile | 3 +- arch/arm/mach-kirkwood/board-dt.c | 88 ++++++++++++++++++++++++++++++++++++++- 2 files changed, 88 insertions(+), 3 deletions(-)
arch/arm/mach-kirkwood/Makefile +1 -2
@@ -1,5 +1,4 @@ -obj-y += common.o pcie.o -obj-$(CONFIG_KIRKWOOD_LEGACY) += irq.o mpp.o +obj-$(CONFIG_KIRKWOOD_LEGACY) += irq.o mpp.o common.o pcie.o obj-$(CONFIG_PM) += pm.o obj-$(CONFIG_MACH_D2NET_V2) += d2net_v2-setup.o lacie_v2-common.o
arch/arm/mach-kirkwood/board-dt.c +87 -1
98 lines not on this page · raw message
Signature · 1 line
1.8.5.3
Arnd Bergmann
maintainerPATCH v2 5/23 ARM: Kirkwood: Seperate board-dt from common and pcie code.
arch/arm/mach-kirkwood/board-dt.c line 56
Quoted 12 lines · On Saturday 15 February 2014 11:20:03 Andrew Lunn wrote:
arch/arm/mach-kirkwood/board-dt.c +12
-0+static void __init kirkwood_l2_init (void ) +{ +#ifdef CONFIG_CACHE_FEROCEON_L2 +#ifdef CONFIG_CACHE_FEROCEON_L2_WRITETHROUGH +writel (readl (L2_CONFIG_REG ) |L2_WRITETHROUGH ,L2_CONFIG_REG ); +feroceon_l2_init (1 ); +#else +writel (readl (L2_CONFIG_REG ) & ~L2_WRITETHROUGH ,L2_CONFIG_REG ); +feroceon_l2_init (0 ); +#endif +#endif +}
I assume this is correct, but I don't understand it. Why is there a configuration option for this? Do both write-through and write-back work on all machines, or could there be a case where some machine actually requires a particular mode? If not, isn't write-back normally "better", so you won't actually ever want to set write-through mode?
Arnd
Andrew Lunn
maintainerPATCH v2 5/23 ARM: Kirkwood: Seperate board-dt from common and pcie code.
Quoted 12 lines · Arnd Bergmann
Quoted 11 lines · On Saturday 15 February 2014 11:20:03 Andrew Lunn wrote:
arch/arm/mach-kirkwood/board-dt.c +11
-0+static void __init kirkwood_l2_init (void ) +{ +#ifdef CONFIG_CACHE_FEROCEON_L2 +#ifdef CONFIG_CACHE_FEROCEON_L2_WRITETHROUGH +writel (readl (L2_CONFIG_REG ) |L2_WRITETHROUGH ,L2_CONFIG_REG ); +feroceon_l2_init (1 ); +#else +writel (readl (L2_CONFIG_REG ) & ~L2_WRITETHROUGH ,L2_CONFIG_REG ); +feroceon_l2_init (0 ); +#endif +#endif
Quoted 8 lines
Quoted 1 line
+}
I assume this is correct, but I don't understand it. Why is there a configuration option for this? Do both write-through and write-back work on all machines, or could there be a case where some machine actually requires a particular mode? If not, isn't write-back normally "better", so you won't actually ever want to set write-through mode?
Hi Arnd
The honest answer is, i've no idea. I'm just shuffling code around in this patch, and not applying my brain as to what this code does....
Maybe JasonG has a better idea of this history of this?
Andrew
PATCH v2 5/23 ARM: Kirkwood: Seperate board-dt from common and pcie code.
Quoted 22 lines · Andrew Lunn
Quoted 12 lines · Arnd Bergmann
Quoted 11 lines · On Saturday 15 February 2014 11:20:03 Andrew Lunn wrote:
arch/arm/mach-kirkwood/board-dt.c +11
-0+static void __init kirkwood_l2_init (void ) +{ +#ifdef CONFIG_CACHE_FEROCEON_L2 +#ifdef CONFIG_CACHE_FEROCEON_L2_WRITETHROUGH +writel (readl (L2_CONFIG_REG ) |L2_WRITETHROUGH ,L2_CONFIG_REG ); +feroceon_l2_init (1 ); +#else +writel (readl (L2_CONFIG_REG ) & ~L2_WRITETHROUGH ,L2_CONFIG_REG ); +feroceon_l2_init (0 ); +#endif +#endif Quoted 8 lines
Quoted 1 line
+}
I assume this is correct, but I don't understand it. Why is there a configuration option for this? Do both write-through and write-back work on all machines, or could there be a case where some machine actually requires a particular mode? If not, isn't write-back normally "better", so you won't actually ever want to set write-through mode?
Quoted 6 lines
Hi Arnd
The honest answer is, i've no idea. I'm just shuffling code around in this patch, and not applying my brain as to what this code does....
Maybe JasonG has a better idea of this history of this?
No idea of the history, but for DMA heavy work loads write-through is better since you spend less cpu cycles doing cache flushing, while for CPU centric work loads write-back is better since you spend less time waiting for memory.
Since these SOCs are popular for storage and networking apps I'm not surprised to see this option.
But a static config option is not really in-line with current thinking on these sorts of things. A DT option would be better (IMHO), but even that is probably not going to be universally loved.
Can we worry about this after Andrew's shuffling is done?
Regards,
Jason
Andrew Lunn
maintainerPATCH v2 5/23 ARM: Kirkwood: Seperate board-dt from common and pcie code.
Quoted 1 line
Can we worry about this after Andrew's shuffling is done?
Hi Jason
I think so. I plan to keep to a config option for the moment and remove the wt-override from DT. We can put it back again later.
Andrew
Arnd Bergmann
maintainerPATCH v2 5/23 ARM: Kirkwood: Seperate board-dt from common and pcie code.
In reply to Jason GunthorpeQuoted 8 lines · On Tuesday 18 February 2014 11:37:46 Jason Gunthorpe wrote:
No idea of the history, but for DMA heavy work loads write-through is better since you spend less cpu cycles doing cache flushing, while for CPU centric work loads write-back is better since you spend less time waiting for memory.
Since these SOCs are popular for storage and networking apps I'm not surprised to see this option.
Ok, that makes much more sense than anything I could come up with ;-)
Quoted 3 lines
But a static config option is not really in-line with current thinking on these sorts of things. A DT option would be better (IMHO), but even that is probably not going to be universally loved.
One of the later patches actually introduced a DT property for it, but the implementation of that seemed incomplete, so the current plan is to keep the Kconfig option for now.
Quoted 1 line
Can we worry about this after Andrew's shuffling is done?
Sure.
Arnd
Andrew Lunn
maintainerPATCH v2 6/23 ARM: Kirkwood: ioremap the cpu_config register before using it.
In reply to Andrew LunnWith the move to mach-mvebu and MULTI_V5, the global iomap for all registers will be going away. So explicitly map the CPU configuration register before using it.
--- arch/arm/mach-kirkwood/board-dt.c | 22 +++++++++++++++------- arch/arm/mach-kirkwood/include/mach/bridge-regs.h | 1 + 2 files changed, 16 insertions(+), 7 deletions(-)
arch/arm/mach-kirkwood/board-dt.c +15 -7
@@ -191,15 +191,23 @@ eth_fixup_skip: } } +/* +* Disable propagation of mbus errors to the CPU local bus, as this +* causes mbus errors (which can occur for example for PCI aborts) to +* throw CPU aborts, which we're not set up to deal with. +*/ +void kirkwood_disable_mbus_error_propagation (void ) +{ +void __iomem *cpu_config; + + cpu_config =ioremap (CPU_CONFIG_PHYS ,4 ); +writel (readl (cpu_config) & ~CPU_CONFIG_ERROR_PROP , cpu_config); +} + +static void __init kirkwood_dt_init (void ) { -/* -* Disable propagation of mbus errors to the CPU local bus, -* as this causes mbus errors (which can occur for example -* for PCI aborts) to throw CPU aborts, which we're not set -* up to deal with. -*/ -writel (readl (CPU_CONFIG ) & ~CPU_CONFIG_ERROR_PROP ,CPU_CONFIG ); +kirkwood_disable_mbus_error_propagation ();BUG_ON (mvebu_mbus_dt_init ());
arch/arm/mach-kirkwood/include/mach/bridge-regs.h +1 -0
@@ -14,6 +14,7 @@#include <mach/kirkwood.h> #define CPU_CONFIG (BRIDGE_VIRT_BASE + 0x0100) +#define CPU_CONFIG_PHYS (BRIDGE_PHYS_BASE + 0x0100)#define CPU_CONFIG_ERROR_PROP 0x00000004#define CPU_CONTROL (BRIDGE_VIRT_BASE + 0x0104)
Signature · 1 line
1.8.5.3
PATCH v2 6/23 ARM: Kirkwood: ioremap the cpu_config register before using it.
Hi Andrew,
On Sat, Feb 15, 2014 at 11:20:04AM +0100, Andrew Lunn wrote:
[..]
Quoted 4 lines
arch/arm/mach-kirkwood/board-dt.c +3
-0+/* +* Disable propagation of mbus errors to the CPU local bus, as this +* causes mbus errors (which can occur for example for PCI aborts) to
arch/arm/mach-kirkwood/board-dt.c eth_fixup_skip: · line 206
Quoted 10 lines
arch/arm/mach-kirkwood/board-dt.c +10
-0+* throw CPU aborts, which we're not set up to deal with. +*/ +void kirkwood_disable_mbus_error_propagation (void ) +{ +void __iomem *cpu_config; + + cpu_config =ioremap (CPU_CONFIG_PHYS ,4 ); +writel (readl (cpu_config) & ~CPU_CONFIG_ERROR_PROP , cpu_config); +} +
Any reason why this function above is not static __init?
And then: any reason why you're not unmapping the region?
(Sorry if this was already discussed)
Signature · 3 lines
Ezequiel Garc?a, Free Electrons Embedded Linux, Kernel and Android Engineering http://free-electrons.com
Andrew Lunn
maintainerPATCH v2 7/23 ARM: Kirkwood: ioremap memory control register
In reply to Andrew LunnTo allow removal of the global map of registers, make the pm code ioremap the registers it needs.
--- arch/arm/mach-kirkwood/include/mach/bridge-regs.h | 1 + arch/arm/mach-kirkwood/pm.c | 9 ++++++--- 2 files changed, 7 insertions(+), 3 deletions(-)
arch/arm/mach-kirkwood/include/mach/bridge-regs.h +1 -0
@@ -80,5 +80,6 @@#define CGC_RESERVED (0x6 << 21)#define MEMORY_PM_CTRL (BRIDGE_VIRT_BASE + 0x118) +#define MEMORY_PM_CTRL_PHYS (BRIDGE_PHYS_BASE + 0x118)#endif
arch/arm/mach-kirkwood/pm.c +6 -3
@@ -21,15 +21,16 @@#include "common.h" static void __iomem *ddr_operation_base; +static void __iomem *memory_pm_ctrl;static void kirkwood_low_power (void ) {u32 mem_pm_ctrl; - mem_pm_ctrl =readl (MEMORY_PM_CTRL ); + mem_pm_ctrl =readl (memory_pm_ctrl);/* Set peripherals to low-power mode */ -writel_relaxed (~0 ,MEMORY_PM_CTRL ); +writel_relaxed (~0 , memory_pm_ctrl);/* Set DDR in self-refresh */ writel_relaxed (0x7 , ddr_operation_base);
@@ -41,7 +42,7 @@ static void kirkwood_low_power(void)*/ cpu_do_idle (); -writel_relaxed (mem_pm_ctrl,MEMORY_PM_CTRL ); +writel_relaxed (mem_pm_ctrl, memory_pm_ctrl); }static int kirkwood_suspend_enter (suspend_state_t state)
@@ -69,5 +70,7 @@ static const struct platform_suspend_ops kirkwood_suspend_ops = {void __init kirkwood_pm_init (void ) { ddr_operation_base =ioremap (DDR_OPERATION_BASE ,4 ); + memory_pm_ctrl =ioremap (MEMORY_PM_CTRL_PHYS ,4 ); +suspend_set_ops (&kirkwood_suspend_ops); }
Signature · 1 line
1.8.5.3
PATCH v2 7/23 ARM: Kirkwood: ioremap memory control register
Quoted 9 lines · Andrew Lunn
To allow removal of the global map of registers, make the pm code ioremap the registers it needs.
Signed-off-by Andrew Lunn <[email protected]>--- arch/arm/mach-kirkwood/include/mach/bridge-regs.h | 1 + arch/arm/mach-kirkwood/pm.c | 9 ++++++--- 2 files changed, 7 insertions(+), 3 deletions(-)
Signature · 3 lines
Ezequiel Garc?a, Free Electrons Embedded Linux, Kernel and Android Engineering http://free-electrons.com
Andrew Lunn
maintainerPATCH v2 8/23 ARM: MVEBU: Add ARCH_MULTI_V7 to SoCs
In reply to Andrew LunnPrepare mach-mvebu to house both ARCH_MULTI_V7 and ARCH_MULTI_V5 systems by adding ARCH_MULTI_V7 to the existing SOCs.
--- arch/arm/mach-mvebu/Kconfig | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-)
arch/arm/mach-mvebu/Kconfig +2 -2
@@ -29,7 +29,7 @@ config MACH_ARMADA_370_XP select CPU_PJ4B config MACH_ARMADA_370 - bool "Marvell Armada 370 boards" + bool "Marvell Armada 370 boards" if ARCH_MULTI_V7 select ARMADA_370_CLK select MACH_ARMADA_370_XP select PINCTRL_ARMADA_370
@@ -38,7 +38,7 @@ config MACH_ARMADA_370 on the Marvell Armada 370 SoC with device tree. config MACH_ARMADA_XP - bool "Marvell Armada XP boards" + bool "Marvell Armada XP boards" if ARCH_MULTI_V7 select ARMADA_XP_CLK select MACH_ARMADA_370_XP select PINCTRL_ARMADA_XP
Signature · 1 line
1.8.5.3
Andrew Lunn
maintainerPATCH v2 9/23 ARM: Orion: Move cache-feroceon-l2.h out of plat-orion
In reply to Andrew LunnWith the gradual move to DT, kirkwood has become a lot less dependent on plat-orion. cache-feroceon-l2.h is the last dependency. Move it out so we can drop plat-orion when building DT only kirkwood boards.
--- arch/arm/include/asm/hardware/cache-feroceon-l2.h | 11 +++++++++++ arch/arm/mach-kirkwood/board-dt.c | 2 +- arch/arm/mach-kirkwood/common.c | 2 +- arch/arm/mach-mv78xx0/common.c | 2 +- arch/arm/mm/cache-feroceon-l2.c | 2 +- arch/arm/plat-orion/include/plat/cache-feroceon-l2.h | 11 ----------- 6 files changed, 15 insertions(+), 15 deletions(-) create mode 100644 arch/arm/include/asm/hardware/cache-feroceon-l2.h delete mode 100644 arch/arm/plat-orion/include/plat/cache-feroceon-l2.h
arch/arm/include/asm/hardware/cache-feroceon-l2.h new file +11 -0
@@ -0,0 +1,11 @@ +/* +* arch/arm/include/asm/hardware/cache-feroceon-l2.h +* +* Copyright (C) 2008 Marvell Semiconductor +* +* This file is licensed under the terms of the GNU General Public +* License version 2. This program is licensed "as is" without any +* warranty of any kind, whether express or implied. +*/ + +extern void __init feroceon_l2_init (int l2_wt_override);
arch/arm/mach-kirkwood/board-dt.c +1 -1
@@ -20,11 +20,11 @@#include <linux/dma-mapping.h> #include <linux/irqchip.h> #include <linux/kexec.h> +#include <asm/hardware/cache-feroceon-l2.h> #include <asm/mach/arch.h> #include <asm/mach/map.h> #include <mach/bridge-regs.h> #include <plat/common.h> -#include <plat/cache-feroceon-l2.h> #include <plat/pcie.h> #include "pm.h"
arch/arm/mach-kirkwood/common.c +1 -1
@@ -25,10 +25,10 @@#include <asm/page.h> #include <asm/mach/map.h> #include <asm/mach/time.h> +#include <asm/hardware/cache-feroceon-l2.h> #include <mach/kirkwood.h> #include <mach/bridge-regs.h> #include <linux/platform_data/asoc-kirkwood.h> -#include <plat/cache-feroceon-l2.h> #include <linux/platform_data/mmc-mvsdio.h> #include <linux/platform_data/mtd-orion_nand.h> #include <linux/platform_data/usb-ehci-orion.h>
arch/arm/mach-mv78xx0/common.c +1 -1
@@ -15,11 +15,11 @@#include <linux/ata_platform.h> #include <linux/clk-provider.h> #include <linux/ethtool.h> +#include <asm/hardware/cache-feroceon-l2.h> #include <asm/mach/map.h> #include <asm/mach/time.h> #include <mach/mv78xx0.h> #include <mach/bridge-regs.h> -#include <plat/cache-feroceon-l2.h> #include <linux/platform_data/usb-ehci-orion.h> #include <linux/platform_data/mtd-orion_nand.h> #include <plat/time.h>
arch/arm/mm/cache-feroceon-l2.c +1 -1
@@ -16,7 +16,7 @@#include <linux/highmem.h> #include <asm/cacheflush.h> #include <asm/cp15.h> -#include <plat/cache-feroceon-l2.h> +#include <asm/hardware/cache-feroceon-l2.h> /* * Low-level cache maintenance operations.
arch/arm/plat-orion/include/plat/cache-feroceon-l2.h deleted +0 -11
@@ -1,11 +0,0 @@ -/* -* arch/arm/plat-orion/include/plat/cache-feroceon-l2.h -* -* Copyright (C) 2008 Marvell Semiconductor -* -* This file is licensed under the terms of the GNU General Public -* License version 2. This program is licensed "as is" without any -* warranty of any kind, whether express or implied. -*/ - -extern void __init feroceon_l2_init (int l2_wt_override);
Signature · 1 line
1.8.5.3
Andrew Lunn
maintainerPATCH v2 10/23 ARM: MM: Add DT binding for Feroceon L2 cache
In reply to Andrew LunnInstantiate the L2 cache from DT. Indicate in DT where the cache control register is and if write through should be made.
---
v2:
Change compatible strings to follow l2x0 convention Only expect register for kirkwood-cache.
Default to write through if no DT node.
Rename writethrough to wt-override to follow l2cc binding. Split kirkwood.dtsi change into a patch of its own.
--- .../devicetree/bindings/arm/mrvl/feroceon.txt | 17 +++++++ arch/arm/include/asm/hardware/cache-feroceon-l2.h | 2 + arch/arm/mach-kirkwood/board-dt.c | 15 +------ arch/arm/mm/cache-feroceon-l2.c | 52 ++++++++++++++++++++++ 4 files changed, 72 insertions(+), 14 deletions(-) create mode 100644 Documentation/devicetree/bindings/arm/mrvl/feroceon.txt
Documentation/devicetree/bindings/arm/mrvl/feroceon.txt new file +17 -0
@@ -0,0 +1,17 @@ +* Marvell Feroceon Cache + +Required properties: +- compatible : Should be either "marvell,ferocean-cache" or + "marvell,kirkwood-cache". + +Optional properties: +- wt-override: If present then L2 is forced to Write through mode +- reg : Address of the L2 cache control register. Mandatory for + "marvell,kirkwood-cache", not used by "marvell,ferocean-cache" + + +Example: + l2: l2-cache at 20128 { + compatible = "marvell,kirkwood-cache"; + reg = <0x20128 0x4>; + };
arch/arm/include/asm/hardware/cache-feroceon-l2.h +2 -0
@@ -9,3 +9,5 @@*/ extern void __init feroceon_l2_init (int l2_wt_override); +extern int __init feroceon_of_init (void ); +
arch/arm/mach-kirkwood/board-dt.c +1 -14
@@ -42,19 +42,6 @@ static void __init kirkwood_map_io(void)iotable_init (kirkwood_io_desc,ARRAY_SIZE (kirkwood_io_desc)); } -static void __init kirkwood_l2_init (void ) -{ -#ifdef CONFIG_CACHE_FEROCEON_L2 -#ifdef CONFIG_CACHE_FEROCEON_L2_WRITETHROUGH -writel (readl (L2_CONFIG_REG ) |L2_WRITETHROUGH ,L2_CONFIG_REG ); -feroceon_l2_init (1 ); -#else -writel (readl (L2_CONFIG_REG ) & ~L2_WRITETHROUGH ,L2_CONFIG_REG ); -feroceon_l2_init (0 ); -#endif -#endif -} -static struct resource kirkwood_cpufreq_resources[] = { [0 ] = { .start =CPU_CONTROL_PHYS ,
@@ -211,7 +198,7 @@ static void __init kirkwood_dt_init(void)BUG_ON (mvebu_mbus_dt_init ()); -kirkwood_l2_init (); +feroceon_of_init ();kirkwood_cpufreq_init ();kirkwood_cpuidle_init ();
arch/arm/mm/cache-feroceon-l2.c +52 -0
66 lines not on this page · raw message
Signature · 1 line
1.8.5.3
Arnd Bergmann
maintainerPATCH v2 10/23 ARM: MM: Add DT binding for Feroceon L2 cache
Quoted 6 lines · On Saturday 15 February 2014 11:20:08 Andrew Lunn wrote:
Instantiate the L2 cache from DT. Indicate in DT where the cache control register is and if write through should be made.
Signed-off-by Andrew Lunn <[email protected]>cc devicetree at vger.kernel.org
I guess this answers part of my question for patch 5, but I also wonder if the run-time setting is correct now with the hardcoded #ifdef in arch/arm/mm/proc-feroceon.S checkign for the Kconfig option. Presumably the code should match whatever is set in the cache control register.
Arnd
Andrew Lunn
maintainerPATCH v2 10/23 ARM: MM: Add DT binding for Feroceon L2 cache
Quoted 8 lines · Arnd Bergmann
Quoted 6 lines · On Saturday 15 February 2014 11:20:08 Andrew Lunn wrote:
Instantiate the L2 cache from DT. Indicate in DT where the cache control register is and if write through should be made.
Signed-off-by Andrew Lunn <[email protected]>cc devicetree at vger.kernel.org
Quoted 5 lines
I guess this answers part of my question for patch 5, but I also wonder if the run-time setting is correct now with the hardcoded #ifdef in
arch/arm/mm/proc-feroceon.Scheckign for theKconfigoption. Presumably the code should match whatever is set in the cache control register.
Humm, yes, good point.
None of the _defconfig's ever turn on CACHE_FEROCEON_L2_WRITETHROUGH. I also did a quick google and could not find any usage of it.
So i see two options:
1) Remove the wr-override from the DT binding and use CACHE_FEROCEON_L2_WRITETHROUGH.
2) Remove CACHE_FEROCEON_L2_WRITETHROUGH and make proc-feroceon.S do the right thing at runtime.
I suspect i will go for 1), it is simpler.
Thanks
Andrew
Arnd Bergmann
maintainerPATCH v2 10/23 ARM: MM: Add DT binding for Feroceon L2 cache
Quoted 6 lines · Andrew Lunn
None of the _defconfig's ever turn on
CACHE_FEROCEON_L2_WRITETHROUGH. I also did a quick google and could not find any usage of it.So i see two options:
Quoted 7 lines
1) Remove the wr-override from the DT binding and use
CACHE_FEROCEON_L2_WRITETHROUGH.2) Remove
CACHE_FEROCEON_L2_WRITETHROUGHand makeproc-feroceon.Sdo the right thing at runtime.I suspect i will go for 1), it is simpler.
Yes, fair enough. I'd hope we could just kill the option altogether, but it's probably hard to find anyone who would remember what it was introduced for, unless Nico knows.
Git history points to
commit 4360bb41920ffacd4a935fa692768129ee5bef4e
Author: Ronen Shitrit <[email protected]> Date: Tue Sep 23 15:28:10 2008 +0300
[ARM] Kirkwood: add support for L2 cache WB/WT selection
Feroceon L2 cache can work in eighther write through or write back mode on Kirkwood. Add the option to configure this mode according to Kconfig.
Arnd
PATCH v2 10/23 ARM: MM: Add DT binding for Feroceon L2 cache
Quoted 10 lines · Arnd Bergmann
Quoted 9 lines · Andrew Lunn
None of the _defconfig's ever turn on
CACHE_FEROCEON_L2_WRITETHROUGH. I also did a quick google and could not find any usage of it.So i see two options:
1) Remove the wr-override from the DT binding and use
CACHE_FEROCEON_L2_WRITETHROUGH.
Quoted 8 lines
Quoted 4 lines
2) Remove
CACHE_FEROCEON_L2_WRITETHROUGHand makeproc-feroceon.Sdo the right thing at runtime.I suspect i will go for 1), it is simpler.
Yes, fair enough. I'd hope we could just kill the option altogether, but it's probably hard to find anyone who would remember what it was introduced for, unless Nico knows.
There was a time when we didn't know what cache mode was the best performance wise. The right answer is "it depends on the work load" of course. Hence it was made optional for people to play with and choose for themselves.
Nicolas
PATCH v2 10/23 ARM: MM: Add DT binding for Feroceon L2 cache
In reply to Andrew LunnQuoted 26 lines · Andrew Lunn
Instantiate the L2 cache from DT. Indicate in DT where the cache control register is and if write through should be made.
Signed-off-by Andrew Lunn <[email protected]>cc devicetree at vger.kernel.org---
v2:
Change compatible strings to follow l2x0 convention Only expect register for kirkwood-cache.
Default to write through if no DT node.
Rename writethrough to wt-override to follow l2cc binding. Splitkirkwood.dtsichange into a patch of its own.--- .../devicetree/bindings/arm/mrvl/feroceon.txt | 17 +++++++ arch/arm/include/asm/hardware/cache-feroceon-l2.h | 2 + arch/arm/mach-kirkwood/board-dt.c | 15 +------ arch/arm/mm/cache-feroceon-l2.c | 52 ++++++++++++++++++++++ 4 files changed, 72 insertions(+), 14 deletions(-) create mode 100644 Documentation/devicetree/bindings/arm/mrvl/feroceon.txtDocumentation/devicetree/bindings/arm/mrvl/feroceon.txt new file +0
-0
Documentation/devicetree/bindings/arm/mrvl/feroceon.txt line 10
Quoted 10 lines
Documentation/devicetree/bindings/arm/mrvl/feroceon.txt new file +10
-0@@ -0,0 +1,17 @@ +* Marvell Feroceon Cache + +Required properties: +- compatible : Should be either "marvell,ferocean-cache" or + "marvell,kirkwood-cache". + +Optional properties: +- wt-override: If present then L2 is forced to Write through mode +- reg : Address of the L2 cache control register. Mandatory for + "marvell,kirkwood-cache", not used by "marvell,ferocean-cache"
s/ferocean/feroceon/
If there's nothing else deserving a new series, I'll tweak this (and the other spelling nits that matter) when I pull in the series.
thx,
Jason.
Quoted 130 lines
Documentation/devicetree/bindings/arm/mrvl/feroceon.txt new file +7
-0+ + +Example: + l2: l2-cache at 20128 { + compatible = "marvell,kirkwood-cache"; + reg = <0x20128 0x4>; + };arch/arm/include/asm/hardware/cache-feroceon-l2.h +2
-0@@ -9,3 +9,5 @@*/ extern void __init feroceon_l2_init (int l2_wt_override); +extern int __init feroceon_of_init (void ); +arch/arm/mach-kirkwood/board-dt.c +1
-14@@ -42,19 +42,6 @@ static void __init kirkwood_map_io(void)iotable_init (kirkwood_io_desc,ARRAY_SIZE (kirkwood_io_desc)); } -static void __init kirkwood_l2_init (void ) -{ -#ifdef CONFIG_CACHE_FEROCEON_L2 -#ifdef CONFIG_CACHE_FEROCEON_L2_WRITETHROUGH -writel (readl (L2_CONFIG_REG ) |L2_WRITETHROUGH ,L2_CONFIG_REG ); -feroceon_l2_init (1 ); -#else -writel (readl (L2_CONFIG_REG ) & ~L2_WRITETHROUGH ,L2_CONFIG_REG ); -feroceon_l2_init (0 ); -#endif -#endif -} -static struct resource kirkwood_cpufreq_resources[] = { [0 ] = { .start =CPU_CONTROL_PHYS ,@@ -211,7 +198,7 @@ static void __init kirkwood_dt_init(void)BUG_ON (mvebu_mbus_dt_init ()); -kirkwood_l2_init (); +feroceon_of_init ();kirkwood_cpufreq_init ();kirkwood_cpuidle_init ();arch/arm/mm/cache-feroceon-l2.c +52
-0@@ -13,11 +13,16 @@*/ #include <linux/init.h> +#include <linux/of.h> +#include <linux/of_address.h> #include <linux/highmem.h> +#include <linux/io.h> #include <asm/cacheflush.h> #include <asm/cp15.h> #include <asm/hardware/cache-feroceon-l2.h> +#define L2_WRITETHROUGH_KIRKWOOD BIT(4) +/* * Low-level cache maintenance operations. * @@ -350,3 +355,50 @@ void __init feroceon_l2_init(int __l2_wt_override)printk (KERN_INFO "Feroceon L2: Cache support initialised%s.\n" , l2_wt_override ?", in WT override mode" :"" ); } +#ifdef CONFIG_OF +static const struct of_device_id feroceon_ids[]__initconst = { + { .compatible ="marvell,kirkwood-cache" }, + { .compatible ="marvell,feroceon-cache" }, + {} +}; + +int __init feroceon_of_init (void ) +{ +struct device_node *node; +void __iomem *base; +bool l2_wt_override = false; +struct resource res; + + node =of_find_matching_node (NULL , feroceon_ids); +if (!node) { +/* +* If we don't know the write through state then +* assume it is write back, as that is the safest +* option. +*/ +feroceon_l2_init (0 ); +return 0 ; + } + +if (of_device_is_compatible (node,"marvell,kirkwood-cache" )) { +if (of_property_read_bool (node,"wt-override" )) + l2_wt_override = true; + +if (of_address_to_resource (node,0 , &res)) +return -ENODEV ; + + base =ioremap (res.start,resource_size (&res)); +if (!base) +return -ENOMEM ; + +if (l2_wt_override) +writel (readl (base) |L2_WRITETHROUGH_KIRKWOOD , base); +else +writel (readl (base) & ~L2_WRITETHROUGH_KIRKWOOD , base); + } + +feroceon_l2_init (l2_wt_override); + +return 0 ; +} +#endif Signature · 7 lines
1.8.5.3 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel at lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Andrew Lunn
maintainerPATCH v2 10/23 ARM: MM: Add DT binding for Feroceon L2 cache
Quoted 10 lines
Documentation/devicetree/bindings/arm/mrvl/feroceon.txt line 10
Quoted 8 lines
Documentation/devicetree/bindings/arm/mrvl/feroceon.txt new file +8
-0+Required properties: +- compatible : Should be either "marvell,ferocean-cache" or + "marvell,kirkwood-cache". + +Optional properties: +- wt-override: If present then L2 is forced to Write through mode +- reg : Address of the L2 cache control register. Mandatory for + "marvell,kirkwood-cache", not used by "marvell,ferocean-cache"s/ferocean/feroceon/
Arg. I thought i had fixed all of those.
Quoted 2 lines
If there's nothing else deserving a new series, I'll tweak this (and the other spelling nits that matter) when I pull in the series.
This patch needs a major bit of re-working. There will definitely be a new series.
Andrew
Andrew Lunn
maintainerPATCH v2 11/23 ARM: Kirkwood: Instantiate L2 cache from DT.
In reply to Andrew LunnNow that the Ferocean L2 cache has a DT binding, make use of it.
--- arch/arm/boot/dts/kirkwood.dtsi | 5 +++++ 1 file changed, 5 insertions(+)
arch/arm/boot/dts/kirkwood.dtsi +5 -0
@@ -161,6 +161,11 @@ #clock-cells = <1>; }; + l2: l2-cache at 20128 { + compatible = "marvell,kirkwood-cache"; + reg = <0x20128 0x4>; + }; + intc: main-interrupt-ctrl at 20200 { compatible = "marvell,orion-intc"; interrupt-controller;
Signature · 1 line
1.8.5.3
Andrew Lunn
maintainerPATCH v2 12/23 ARM: Fix default CPU selection for ARCH_MULTI_V5
In reply to Andrew LunnCPU_ARM926T should be selected if no other CPU is. Put the ! in the right place so this works.
--- arch/arm/Kconfig | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
arch/arm/Kconfig +1 -1
@@ -898,7 +898,7 @@ config ARCH_MULTI_V5 bool "ARMv5 based platforms (ARM926T, XSCALE, PJ1, ...)" depends on !ARCH_MULTI_V6_V7 select ARCH_MULTI_V4_V5 - select CPU_ARM926T if (!CPU_ARM946E || CPU_ARM1020 || \ + select CPU_ARM926T if !(CPU_ARM946E || CPU_ARM1020 || \ CPU_ARM1020E || CPU_ARM1022 || CPU_ARM1026 || \ CPU_XSCALE || CPU_XSC3 || CPU_MOHAWK || CPU_FEROCEON)
Signature · 1 line
1.8.5.3
Arnd Bergmann
maintainerPATCH v2 12/23 ARM: Fix default CPU selection for ARCH_MULTI_V5
Quoted 5 lines · Andrew Lunn
CPU_ARM926Tshould be selected if no other CPU is. Put the ! in the right place so this works.Signed-off-by Andrew Lunn <[email protected]>cc Arnd Bergmann <[email protected]>
PATCH v2 12/23 ARM: Fix default CPU selection for ARCH_MULTI_V5
In reply to Andrew LunnAndrew,
12, 13, and 14 should go into rmk's patch tracker.
Russell, we'd really like to move kirkwood DT into mach-mvebu for v3.15. Is there any possibility you could create a topic branch for us containing the this patch and the other two I mentioned, above?
Or, if you don't think there will be any significant conflicts, would you mind Acking these three for us to take through mvebu/arm-soc?
thx,
Jason.
Quoted 30 lines · Andrew Lunn
CPU_ARM926Tshould be selected if no other CPU is. Put the ! in the right place so this works.Signed-off-by Andrew Lunn <[email protected]>cc Arnd Bergmann <[email protected]>--- arch/arm/Kconfig | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)arch/arm/Kconfig +1
-1@@ -898,7 +898,7 @@ config ARCH_MULTI_V5 bool "ARMv5 based platforms (ARM926T, XSCALE, PJ1, ...)" depends on !ARCH_MULTI_V6_V7 select ARCH_MULTI_V4_V5 - select CPU_ARM926T if (!CPU_ARM946E || CPU_ARM1020 || \ + select CPU_ARM926T if !(CPU_ARM946E || CPU_ARM1020 || \ CPU_ARM1020E || CPU_ARM1022 || CPU_ARM1026 || \ CPU_XSCALE || CPU_XSC3 || CPU_MOHAWK || CPU_FEROCEON)Signature · 7 lines
1.8.5.3 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel at lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Andrew Lunn
maintainerPATCH v2 13/23 ARM: Fix MULTI_TLB for feroceon
In reply to Andrew LunnFeroceon has the same flush operations as v4wbi, but has an additional flag, TLB_L2CLEAN_FR. When building with MULTI_TLB this flag is placed into cpu_tlb.tlb_flags, so there needs to be a cpu_tlb specifically for feroceon, rather than sharing the v4wbi.
--- arch/arm/mm/proc-feroceon.S | 2 +- arch/arm/mm/tlb-v4wbi.S | 3 +++ 2 files changed, 4 insertions(+), 1 deletion(-)
arch/arm/mm/proc-feroceon.S +1 -1
@@ -607,7 +607,7 @@ __\name\()_proc_info: .long HWCAP_SWP|HWCAP_HALF|HWCAP_THUMB|HWCAP_FAST_MULT|HWCAP_EDSP .long \cpu_name .long feroceon_processor_functions - .long v4wbi_tlb_fns + .long fr_tlb_fns .long feroceon_user_fns .long \cache .size __\name\()_proc_info, . - __\name\()_proc_info
arch/arm/mm/tlb-v4wbi.S +3 -0
@@ -28,6 +28,7 @@ * - mm - mm_struct describing address space */ .align 5 +ENTRY(fr_flush_user_tlb_range) ENTRY(v4wbi_flush_user_tlb_range) vma_vm_mm ip, r2 act_mm r3 @ get current->active_mm
@@ -46,6 +47,7 @@ ENTRY(v4wbi_flush_user_tlb_range) blo 1b mov pc, lr +ENTRY(fr_flush_kern_tlb_range) ENTRY(v4wbi_flush_kern_tlb_range) mov r3, #0 mcr p15, 0, r3, c7, c10, 4 @ drain WB
@@ -62,3 +64,4 @@ ENTRY(v4wbi_flush_kern_tlb_range) /* define struct cpu_tlb_fns (see <asm/tlbflush.h> and proc-macros.S) */ define_tlb_functions v4wbi, v4wbi_tlb_flags + define_tlb_functions fr, fr_tlb_flags
Signature · 1 line
1.8.5.3
Andrew Lunn
maintainerPATCH v2 14/23 ARM: MM Enable building Feroceon L2 cache controller with ARCH_MVEBU
In reply to Andrew LunnKirkwood, which uses the Feroceon L2 cache controller will soon be moving into mach-mvebu. Allow the cache controller to be built in this situration.
--- arch/arm/mm/Kconfig | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
arch/arm/mm/Kconfig +1 -1
@@ -855,7 +855,7 @@ config OUTER_CACHE_SYNC config CACHE_FEROCEON_L2 bool "Enable the Feroceon L2 cache controller" - depends on ARCH_KIRKWOOD || ARCH_MV78XX0 + depends on ARCH_KIRKWOOD || ARCH_MV78XX0 || ARCH_MVEBU default y select OUTER_CACHE help
Signature · 1 line
1.8.5.3
Andrew Lunn
maintainerPATCH v2 15/23 ARM: Move kirkwood DT boards into mach-mvebu
In reply to Andrew LunnMove the kirkwood DT support into mach-mvebu, and make them part of ARCH_MULTI_V5. Minimal changes have been made in order to make it boot. Cleanup of the header files and intergration with mvebu will take place in following patches.
--- arch/arm/boot/dts/Makefile | 34 ++-- arch/arm/mach-mvebu/Kconfig | 24 ++- arch/arm/mach-mvebu/Makefile | 1 + arch/arm/mach-mvebu/include/mach/bridge-regs.h | 85 ++++++++++ arch/arm/mach-mvebu/include/mach/kirkwood.h | 142 +++++++++++++++++ arch/arm/mach-mvebu/kirkwood-pm.c | 76 +++++++++ arch/arm/mach-mvebu/kirkwood-pm.h | 26 ++++ arch/arm/mach-mvebu/kirkwood.c | 208 +++++++++++++++++++++++++ 8 files changed, 578 insertions(+), 18 deletions(-) create mode 100644 arch/arm/mach-mvebu/include/mach/bridge-regs.h create mode 100644 arch/arm/mach-mvebu/include/mach/kirkwood.h create mode 100644 arch/arm/mach-mvebu/kirkwood-pm.c create mode 100644 arch/arm/mach-mvebu/kirkwood-pm.h create mode 100644 arch/arm/mach-mvebu/kirkwood.c
arch/arm/boot/dts/Makefile +17 -17
@@ -82,7 +82,23 @@ dtb-$(CONFIG_ARCH_HIGHBANK) += highbank.dtb \ dtb-$(CONFIG_ARCH_INTEGRATOR) += integratorap.dtb \ integratorcp.dtb dtb-$(CONFIG_ARCH_LPC32XX) += ea3250.dtb phy3250.dtb -dtb-$(CONFIG_ARCH_KIRKWOOD) += kirkwood-cloudbox.dtb \ +dtb-$(CONFIG_ARCH_MARCO) += marco-evb.dtb +dtb-$(CONFIG_ARCH_MOXART) += moxart-uc7112lx.dtb +dtb-$(CONFIG_ARCH_MSM) += qcom-msm8660-surf.dtb \ + qcom-msm8960-cdp.dtb \ + qcom-apq8074-dragonboard.dtb +dtb-$(CONFIG_ARCH_MVEBU) += armada-370-db.dtb \ + armada-370-mirabox.dtb \ + armada-370-netgear-rn102.dtb \ + armada-370-netgear-rn104.dtb \ + armada-370-rd.dtb \ + armada-xp-axpwifiap.dtb \ + armada-xp-db.dtb \ + armada-xp-gp.dtb \ + armada-xp-netgear-rn2120.dtb \ + armada-xp-matrix.dtb \ + armada-xp-openblocks-ax3-4.dtb \ + kirkwood-cloudbox.dtb \ kirkwood-db-88f6281.dtb \ kirkwood-db-88f6282.dtb \ kirkwood-dns320.dtb \
@@ -116,22 +132,6 @@ dtb-$(CONFIG_ARCH_KIRKWOOD) += kirkwood-cloudbox.dtb \ kirkwood-topkick.dtb \ kirkwood-ts219-6281.dtb \ kirkwood-ts219-6282.dtb -dtb-$(CONFIG_ARCH_MARCO) += marco-evb.dtb -dtb-$(CONFIG_ARCH_MOXART) += moxart-uc7112lx.dtb -dtb-$(CONFIG_ARCH_MSM) += qcom-msm8660-surf.dtb \ - qcom-msm8960-cdp.dtb \ - qcom-apq8074-dragonboard.dtb -dtb-$(CONFIG_ARCH_MVEBU) += armada-370-db.dtb \ - armada-370-mirabox.dtb \ - armada-370-netgear-rn102.dtb \ - armada-370-netgear-rn104.dtb \ - armada-370-rd.dtb \ - armada-xp-axpwifiap.dtb \ - armada-xp-db.dtb \ - armada-xp-gp.dtb \ - armada-xp-netgear-rn2120.dtb \ - armada-xp-matrix.dtb \ - armada-xp-openblocks-ax3-4.dtb dtb-$(CONFIG_ARCH_MXC) += \ imx25-karo-tx25.dtb \ imx25-pdk.dtb \
arch/arm/mach-mvebu/Kconfig +23 -1
@@ -1,5 +1,5 @@ config ARCH_MVEBU - bool "Marvell SOCs with Device Tree support" if ARCH_MULTI_V7 + bool "Marvell SOCs with Device Tree support" if (ARCH_MULTI_V7 || ARCH_MULTI_V5) select ARCH_SUPPORTS_BIG_ENDIAN select CLKSRC_MMIO select COMMON_CLK
@@ -46,6 +46,28 @@ config MACH_ARMADA_XP Say 'Y' here if you want your kernel to support boards based on the Marvell Armada XP SoC with device tree. +config MACH_KIRKWOOD + bool "Marvell Kirkwood boards" if ARCH_MULTI_V5 + select ARCH_HAS_CPUFREQ + select ARCH_REQUIRE_GPIOLIB + select CPU_FEROCEON + select KIRKWOOD_CLK + select OF_IRQ + select ORION_IRQCHIP + select ORION_TIMER + select PCI + select PCI_QUIRKS + select PINCTRL_KIRKWOOD + select POWER_SUPPLY + select POWER_RESET + select POWER_RESET_GPIO + select REGULATOR + select REGULATOR_FIXED_VOLTAGE + select USE_OF + help + Say 'Y' here if you want your kernel to support boards based + on the Marvell Kirkwood device tree. + endmenu endif
arch/arm/mach-mvebu/Makefile +1 -0
@@ -8,3 +8,4 @@ obj-$(CONFIG_MACH_ARMADA_370_XP) += armada-370-xp.o obj-$(CONFIG_ARCH_MVEBU) += coherency.o coherency_ll.o pmsu.o obj-$(CONFIG_SMP) += platsmp.o headsmp.o obj-$(CONFIG_HOTPLUG_CPU) += hotplug.o +obj-$(CONFIG_MACH_KIRKWOOD) += kirkwood.o kirkwood-pm.o
arch/arm/mach-mvebu/include/mach/bridge-regs.h new file +85 -0
85 lines not on this page · raw message
arch/arm/mach-mvebu/include/mach/kirkwood.h new file +142 -0
142 lines not on this page · raw message
arch/arm/mach-mvebu/kirkwood-pm.c new file +76 -0
76 lines not on this page · raw message
arch/arm/mach-mvebu/kirkwood-pm.h new file +26 -0
@@ -0,0 +1,26 @@ +/* +* Power Management driver for Marvell Kirkwood SoCs +* +* Copyright (C) 2013 Ezequiel Garcia <[email protected]> +* Copyright (C) 2010 Simon Guinot <[email protected]> +* +* This program is free software; you can redistribute it and/or modify +* it under the terms of the GNU General Public License, +* version 2 of the License. +* +* This program is distributed in the hope that it will be useful, +* but WITHOUT ANY WARRANTY; without even the implied warranty of +* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +* GNU General Public License for more details. +*/ + +#ifndef __ARCH_KIRKWOOD_PM_H +#define __ARCH_KIRKWOOD_PM_H + +#ifdef CONFIG_PM +void kirkwood_pm_init (void ); +#else +static inline void kirkwood_pm_init (void ) {}; +#endif + +#endif
arch/arm/mach-mvebu/kirkwood.c new file +208 -0
208 lines not on this page · raw message
Signature · 1 line
1.8.5.3
Andrew Lunn
maintainerPATCH v2 16/23 ARM: MVEBU: Let kirkwood use the system controller for restart
In reply to Andrew LunnThe mvebu system controller already supports restarting orion systems. Remove all the C code which will be replaced by the system controller.
---
Split the patch into two, DT goes into a new patch
--- arch/arm/mach-mvebu/kirkwood.c | 20 ++------------------ 1 file changed, 2 insertions(+), 18 deletions(-)
arch/arm/mach-mvebu/kirkwood.c +2 -18
@@ -27,6 +27,7 @@#include <plat/common.h> #include <plat/pcie.h> #include "kirkwood-pm.h" +#include "common.h" static struct resource kirkwood_cpufreq_resources[] = { [0 ] = {
@@ -68,23 +69,6 @@ static void __init kirkwood_cpuidle_init(void)platform_device_register (&kirkwood_cpuidle); } -/* Temporary here since mach-mvebu has a function we can use */ -static void kirkwood_restart (enum reboot_mode mode,const char *cmd) -{ -/* -* Enable soft reset to assert RSTOUTn. -*/ -writel (SOFT_RESET_OUT_EN , RSTOUTn_MASK); - -/* -* Assert soft reset. -*/ -writel (SOFT_RESET ,SYSTEM_SOFT_RESET ); - -while (1 ) - ; -} -#define MV643XX_ETH_MAC_ADDR_LOW 0x0414#define MV643XX_ETH_MAC_ADDR_HIGH 0x0418
@@ -203,6 +187,6 @@ static const char * const kirkwood_dt_board_compat[] = {DT_MACHINE_START (KIRKWOOD_DT ,"Marvell Kirkwood (Flattened Device Tree)" )/* Maintainer: Jason Cooper <[email protected]> */ .init_machine = kirkwood_dt_init, - .restart = kirkwood_restart, + .restart = mvebu_restart, .dt_compat = kirkwood_dt_board_compat,MACHINE_END
Signature · 1 line
1.8.5.3
Andrew Lunn
maintainerPATCH v2 17/23 ARM: MVEBU: Instantiate system controller in kirkwood.dtsi
In reply to Andrew LunnMake use of the mvebu system controller, by placing a node into the dtsi file.
--- arch/arm/boot/dts/kirkwood.dtsi | 5 +++++ 1 file changed, 5 insertions(+)
arch/arm/boot/dts/kirkwood.dtsi +5 -0
@@ -145,6 +145,11 @@ reg = <0x20000 0x80>, <0x1500 0x20>; }; + system-controller at 20000 { + compatible = "marvell,orion-system-controller"; + reg = <0x20000 0x120>; + }; + bridge_intc: bridge-interrupt-ctrl at 20110 { compatible = "marvell,orion-bridge-intc"; interrupt-controller;
Signature · 1 line
1.8.5.3
Andrew Lunn
maintainerPATCH v2 18/23 drivers: Enable building of Kirkwood drivers for mach-mvebu
In reply to Andrew LunnWith the move to mach-mvebu, drivers Kconfig need tweeking to allow the kirkwood specific drivers to be built.
v2
Simplify cpufreq/Kconfig.arm
--- drivers/cpufreq/Kconfig.arm | 2 +- drivers/cpuidle/Kconfig.arm | 2 +- drivers/leds/Kconfig | 4 ++-- drivers/phy/Kconfig | 2 +- drivers/thermal/Kconfig | 2 +- sound/soc/kirkwood/Kconfig | 2 +- 6 files changed, 7 insertions(+), 7 deletions(-)
drivers/cpufreq/Kconfig.arm +1 -1
@@ -113,7 +113,7 @@ config ARM_INTEGRATOR If in doubt, say Y. config ARM_KIRKWOOD_CPUFREQ - def_bool ARCH_KIRKWOOD && OF + def_bool MACH_KIRKWOOD help This adds the CPUFreq driver for Marvell Kirkwood SoCs.
drivers/cpuidle/Kconfig.arm +1 -1
@@ -22,7 +22,7 @@ config ARM_HIGHBANK_CPUIDLE config ARM_KIRKWOOD_CPUIDLE bool "CPU Idle Driver for Marvell Kirkwood SoCs" - depends on ARCH_KIRKWOOD + depends on ARCH_KIRKWOOD || MACH_KIRKWOOD help This adds the CPU Idle driver for Marvell Kirkwood SoCs.
drivers/leds/Kconfig +2 -2
@@ -421,7 +421,7 @@ config LEDS_MC13783 config LEDS_NS2 tristate "LED support for Network Space v2 GPIO LEDs" depends on LEDS_CLASS - depends on ARCH_KIRKWOOD + depends on ARCH_KIRKWOOD || MACH_KIRKWOOD default y help This option enable support for the dual-GPIO LED found on the
@@ -431,7 +431,7 @@ config LEDS_NS2 config LEDS_NETXBIG tristate "LED support for Big Network series LEDs" depends on LEDS_CLASS - depends on ARCH_KIRKWOOD + depends on ARCH_KIRKWOOD || MACH_KIRKWOOD default y help This option enable support for LEDs found on the LaCie 2Big
drivers/phy/Kconfig +1 -1
@@ -24,7 +24,7 @@ config PHY_EXYNOS_MIPI_VIDEO config PHY_MVEBU_SATA def_bool y - depends on ARCH_KIRKWOOD || ARCH_DOVE + depends on ARCH_KIRKWOOD || ARCH_DOVE || MACH_KIRKWOOD depends on OF select GENERIC_PHY
drivers/thermal/Kconfig +1 -1
@@ -142,7 +142,7 @@ config RCAR_THERMAL config KIRKWOOD_THERMAL tristate "Temperature sensor on Marvell Kirkwood SoCs" - depends on ARCH_KIRKWOOD + depends on ARCH_KIRKWOOD || MACH_KIRKWOOD depends on OF help Support for the Kirkwood thermal sensor driver into the Linux thermal
sound/soc/kirkwood/Kconfig +1 -1
@@ -1,6 +1,6 @@ config SND_KIRKWOOD_SOC tristate "SoC Audio for the Marvell Kirkwood and Dove chips" - depends on ARCH_KIRKWOOD || ARCH_DOVE || COMPILE_TEST + depends on ARCH_KIRKWOOD || ARCH_DOVE || MACH_KIRKWOOD || COMPILE_TEST help Say Y or M if you want to add support for codecs attached to the Kirkwood I2S interface. You will also need to select the
Signature · 1 line
1.8.5.3
PATCH v2 18/23 drivers: Enable building of Kirkwood drivers for mach-mvebu
Andrew,
Please Cc; this to all of the relevant maintainers to collect Acks.
thx,
Jason.
Quoted 109 lines · Andrew Lunn
With the move to mach-mvebu, drivers
Kconfigneed tweeking to allow the kirkwood specific drivers to be built.Signed-off-by Andrew Lunn <[email protected]>v2
Simplify cpufreq/Kconfig.arm--- drivers/cpufreq/Kconfig.arm | 2 +- drivers/cpuidle/Kconfig.arm | 2 +- drivers/leds/Kconfig | 4 ++-- drivers/phy/Kconfig | 2 +- drivers/thermal/Kconfig | 2 +- sound/soc/kirkwood/Kconfig | 2 +- 6 files changed, 7 insertions(+), 7 deletions(-)drivers/cpufreq/Kconfig.arm +1
-1@@ -113,7 +113,7 @@ config ARM_INTEGRATOR If in doubt, say Y. config ARM_KIRKWOOD_CPUFREQ - def_bool ARCH_KIRKWOOD && OF + def_bool MACH_KIRKWOOD help This adds the CPUFreq driver for Marvell Kirkwood SoCs.drivers/cpuidle/Kconfig.arm +1
-1@@ -22,7 +22,7 @@ config ARM_HIGHBANK_CPUIDLE config ARM_KIRKWOOD_CPUIDLE bool "CPU Idle Driver for Marvell Kirkwood SoCs" - depends on ARCH_KIRKWOOD + depends on ARCH_KIRKWOOD || MACH_KIRKWOOD help This adds the CPU Idle driver for Marvell Kirkwood SoCs.drivers/leds/Kconfig +2
-2@@ -421,7 +421,7 @@ config LEDS_MC13783 config LEDS_NS2 tristate "LED support for Network Space v2 GPIO LEDs" depends on LEDS_CLASS - depends on ARCH_KIRKWOOD + depends on ARCH_KIRKWOOD || MACH_KIRKWOOD default y help This option enable support for the dual-GPIO LED found on the@@ -431,7 +431,7 @@ config LEDS_NS2 config LEDS_NETXBIG tristate "LED support for Big Network series LEDs" depends on LEDS_CLASS - depends on ARCH_KIRKWOOD + depends on ARCH_KIRKWOOD || MACH_KIRKWOOD default y help This option enable support for LEDs found on the LaCie 2Bigdrivers/phy/Kconfig +1
-1@@ -24,7 +24,7 @@ config PHY_EXYNOS_MIPI_VIDEO config PHY_MVEBU_SATA def_bool y - depends on ARCH_KIRKWOOD || ARCH_DOVE + depends on ARCH_KIRKWOOD || ARCH_DOVE || MACH_KIRKWOOD depends on OF select GENERIC_PHYdrivers/thermal/Kconfig +1
-1@@ -142,7 +142,7 @@ config RCAR_THERMAL config KIRKWOOD_THERMAL tristate "Temperature sensor on Marvell Kirkwood SoCs" - depends on ARCH_KIRKWOOD + depends on ARCH_KIRKWOOD || MACH_KIRKWOOD depends on OF help Support for the Kirkwood thermal sensor driver into the Linux thermalsound/soc/kirkwood/Kconfig +1
-1@@ -1,6 +1,6 @@ config SND_KIRKWOOD_SOC tristate "SoC Audio for the Marvell Kirkwood and Dove chips" - depends on ARCH_KIRKWOOD || ARCH_DOVE || COMPILE_TEST + depends on ARCH_KIRKWOOD || ARCH_DOVE || MACH_KIRKWOOD || COMPILE_TEST help Say Y or M if you want to add support for codecs attached to the Kirkwood I2S interface. You will also need to select theSignature · 7 lines
1.8.5.3 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel at lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Andrew Lunn
maintainerPATCH v2 19/23 ARM: MVEBU: Enable mvebu-soc-id on Kirkwood
In reply to Andrew LunnAdd the Kirkwood PCIe compatibility string to mvebu-soc-id, so that it can get the SoC ID and revision from the PCIe endpoints.
--- arch/arm/mach-mvebu/mvebu-soc-id.c | 1 + 1 file changed, 1 insertion(+)
arch/arm/mach-mvebu/mvebu-soc-id.c +1 -0
@@ -38,6 +38,7 @@ static bool is_id_valid;static const struct of_device_id mvebu_pcie_of_match_table[] = { { .compatible ="marvell,armada-xp-pcie" , }, { .compatible ="marvell,armada-370-pcie" , }, + { .compatible ="marvell,kirkwood-pcie" }, {}, };
Signature · 1 line
1.8.5.3
Andrew Lunn
maintainerPATCH v2 20/23 ARM: config: Add a multi_v5_defconfig
In reply to Andrew LunnTo allow regression build testing of multi v5 systems, add a multi_v5_defconfig, similar to the multi_v7_defconfig. This is based on kirkwood_defconfig, but with a few other boards added which claim to be MULTI_v5.
--- arch/arm/configs/multi_v5_defconfig | 183 ++++++++++++++++++++++++++++++++++++ 1 file changed, 183 insertions(+) create mode 100644 arch/arm/configs/multi_v5_defconfig
arch/arm/configs/multi_v5_defconfig new file +183 -0
@@ -0,0 +1,183 @@ +CONFIG_SYSVIPC=y +CONFIG_NO_HZ=y +CONFIG_HIGH_RES_TIMERS=y +CONFIG_LOG_BUF_SHIFT=19 +CONFIG_PROFILING=y +CONFIG_OPROFILE=y +CONFIG_KPROBES=y +CONFIG_MODULES=y +CONFIG_MODULE_UNLOAD=y +# CONFIG_BLK_DEV_BSG is not set +# CONFIG_ARCH_MULTI_V7 is not set +CONFIG_ARCH_MVEBU=y +CONFIG_MACH_KIRKWOOD=y +CONFIG_ARCH_MXC=y +CONFIG_MACH_IMX25_DT=y +CONFIG_MACH_IMX27_DT=y +CONFIG_ARCH_U300=y +CONFIG_PCI_MVEBU=y +CONFIG_PREEMPT=y +CONFIG_AEABI=y +CONFIG_HIGHMEM=y +CONFIG_ZBOOT_ROM_TEXT=0x0 +CONFIG_ZBOOT_ROM_BSS=0x0 +CONFIG_ARM_APPENDED_DTB=y +CONFIG_ARM_ATAG_DTB_COMPAT=y +CONFIG_CPU_FREQ=y +CONFIG_CPU_FREQ_STAT_DETAILS=y +CONFIG_CPU_FREQ_DEFAULT_GOV_ONDEMAND=y +CONFIG_CPU_IDLE=y +CONFIG_ARM_KIRKWOOD_CPUIDLE=y +CONFIG_NET=y +CONFIG_PACKET=y +CONFIG_UNIX=y +CONFIG_INET=y +CONFIG_IP_MULTICAST=y +CONFIG_IP_PNP=y +CONFIG_IP_PNP_DHCP=y +CONFIG_IP_PNP_BOOTP=y +# CONFIG_IPV6 is not set +CONFIG_NET_PKTGEN=m +CONFIG_CFG80211=y +CONFIG_MAC80211=y +CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" +CONFIG_MTD=y +CONFIG_MTD_CMDLINE_PARTS=y +CONFIG_MTD_BLOCK=y +CONFIG_MTD_CFI=y +CONFIG_MTD_JEDECPROBE=y +CONFIG_MTD_CFI_ADV_OPTIONS=y +CONFIG_MTD_CFI_GEOMETRY=y +# CONFIG_MTD_MAP_BANK_WIDTH_4 is not set +CONFIG_MTD_CFI_INTELEXT=y +CONFIG_MTD_CFI_STAA=y +CONFIG_MTD_PHYSMAP=y +CONFIG_MTD_M25P80=y +CONFIG_MTD_NAND=y +CONFIG_MTD_NAND_ORION=y +CONFIG_BLK_DEV_LOOP=y +CONFIG_EEPROM_AT24=y +# CONFIG_SCSI_PROC_FS is not set +CONFIG_BLK_DEV_SD=y +CONFIG_BLK_DEV_SR=m +CONFIG_CHR_DEV_SG=m +CONFIG_ATA=y +CONFIG_SATA_AHCI=y +CONFIG_SATA_MV=y +CONFIG_NETDEVICES=y +CONFIG_NET_DSA_MV88E6123_61_65=y +CONFIG_MV643XX_ETH=y +CONFIG_R8169=y +CONFIG_MARVELL_PHY=y +CONFIG_LIBERTAS=y +CONFIG_LIBERTAS_SDIO=y +CONFIG_INPUT_EVDEV=y +CONFIG_KEYBOARD_GPIO=y +# CONFIG_INPUT_MOUSE is not set +CONFIG_LEGACY_PTY_COUNT=16 +# CONFIG_DEVKMEM is not set +CONFIG_SERIAL_8250=y +CONFIG_SERIAL_8250_CONSOLE=y +CONFIG_SERIAL_8250_RUNTIME_UARTS=2 +CONFIG_SERIAL_OF_PLATFORM=y +# CONFIG_HW_RANDOM is not set +CONFIG_I2C=y +# CONFIG_I2C_COMPAT is not set +CONFIG_I2C_CHARDEV=y +CONFIG_I2C_MV64XXX=y +CONFIG_I2C_NOMADIK=y +CONFIG_SPI=y +CONFIG_SPI_ORION=y +CONFIG_GPIO_SYSFS=y +CONFIG_POWER_RESET_QNAP=y +CONFIG_SENSORS_ADT7475=y +CONFIG_SENSORS_LM63=y +CONFIG_SENSORS_LM75=y +CONFIG_SENSORS_LM85=y +CONFIG_THERMAL=y +CONFIG_KIRKWOOD_THERMAL=y +CONFIG_WATCHDOG=y +# CONFIG_ABX500_CORE is not set +CONFIG_SOUND=y +CONFIG_SND=y +CONFIG_SND_SOC=y +CONFIG_SND_KIRKWOOD_SOC=y +CONFIG_HID_DRAGONRISE=y +CONFIG_HID_GYRATION=y +CONFIG_HID_TWINHAN=y +CONFIG_HID_NTRIG=y +CONFIG_HID_PANTHERLORD=y +CONFIG_HID_PETALYNX=y +CONFIG_HID_SAMSUNG=y +CONFIG_HID_SONY=y +CONFIG_HID_SUNPLUS=y +CONFIG_HID_GREENASIA=y +CONFIG_HID_SMARTJOYPLUS=y +CONFIG_HID_TOPSEED=y +CONFIG_HID_THRUSTMASTER=y +CONFIG_HID_ZEROPLUS=y +CONFIG_USB=y +CONFIG_USB_XHCI_HCD=y +CONFIG_USB_EHCI_HCD=y +CONFIG_USB_EHCI_ROOT_HUB_TT=y +CONFIG_USB_PRINTER=m +CONFIG_USB_STORAGE=y +CONFIG_USB_STORAGE_DATAFAB=y +CONFIG_USB_STORAGE_FREECOM=y +CONFIG_USB_STORAGE_SDDR09=y +CONFIG_USB_STORAGE_SDDR55=y +CONFIG_USB_STORAGE_JUMPSHOT=y +CONFIG_MMC=y +CONFIG_SDIO_UART=y +CONFIG_MMC_MVSDIO=y +CONFIG_NEW_LEDS=y +CONFIG_LEDS_CLASS=y +CONFIG_LEDS_GPIO=y +CONFIG_LEDS_TRIGGERS=y +CONFIG_LEDS_TRIGGER_TIMER=y +CONFIG_LEDS_TRIGGER_HEARTBEAT=y +CONFIG_LEDS_TRIGGER_DEFAULT_ON=y +CONFIG_RTC_CLASS=y +CONFIG_RTC_DRV_RS5C372=y +CONFIG_RTC_DRV_PCF8563=y +CONFIG_RTC_DRV_S35390A=y +CONFIG_RTC_DRV_MV=y +CONFIG_DMADEVICES=y +CONFIG_MV_XOR=y +CONFIG_EXT2_FS=y +CONFIG_EXT3_FS=y +# CONFIG_EXT3_FS_XATTR is not set +CONFIG_EXT4_FS=y +CONFIG_ISO9660_FS=m +CONFIG_JOLIET=y +CONFIG_UDF_FS=m +CONFIG_MSDOS_FS=y +CONFIG_VFAT_FS=y +CONFIG_TMPFS=y +CONFIG_JFFS2_FS=y +CONFIG_CRAMFS=y +CONFIG_NFS_FS=y +CONFIG_ROOT_NFS=y +CONFIG_NLS_CODEPAGE_437=y +CONFIG_NLS_CODEPAGE_850=y +CONFIG_NLS_ISO8859_1=y +CONFIG_NLS_ISO8859_2=y +CONFIG_NLS_UTF8=y +CONFIG_DEBUG_INFO=y +CONFIG_DEBUG_FS=y +CONFIG_MAGIC_SYSRQ=y +CONFIG_DEBUG_KERNEL=y +# CONFIG_SCHED_DEBUG is not set +# CONFIG_DEBUG_PREEMPT is not set +# CONFIG_FTRACE is not set +CONFIG_DEBUG_USER=y +CONFIG_DEBUG_LL=y +CONFIG_DEBUG_MVEBU_UART_ALTERNATE=y +CONFIG_DEBUG_UART_VIRT=0xfed12000 +CONFIG_EARLY_PRINTK=y +CONFIG_CRYPTO_CBC=m +CONFIG_CRYPTO_PCBC=m +# CONFIG_CRYPTO_ANSI_CPRNG is not set +CONFIG_CRYPTO_DEV_MV_CESA=y +CONFIG_CRC_CCITT=y +CONFIG_LIBCRC32C=y
Signature · 1 line
1.8.5.3
Arnd Bergmann
maintainerPATCH v2 20/23 ARM: config: Add a multi_v5_defconfig
Quoted 6 lines · On Saturday 15 February 2014 11:20:18 Andrew Lunn wrote:
To allow regression build testing of multi v5 systems, add a
multi_v5_defconfig, similar to themulti_v7_defconfig. This is based onkirkwood_defconfig, but with a few other boards added which claim to beMULTI_v5.Signed-off-by Andrew Lunn <[email protected]>
How about making this a multi_v4_v5_defconfig? We have a much smaller number of v4/v4t platforms (moxart, i.MX1) that are multiplatform capable or could besome so in the future (clps711x, gemini, at91rm9200, some s3c24xx, omap15xx, integrator) compared to the multitude of v5 platforms, so it might not be useful to start a separate multi_v4_defconfig.
OTOH if there is a significant performance impact in enabling CPU_32v4 and CPU_32v4T, we probably want to keep them separate.
Any opinions?
Arnd
PATCH v2 20/23 ARM: config: Add a multi_v5_defconfig
Quoted 15 lines · Arnd Bergmann
Quoted 6 lines · On Saturday 15 February 2014 11:20:18 Andrew Lunn wrote:
To allow regression build testing of multi v5 systems, add a
multi_v5_defconfig, similar to themulti_v7_defconfig. This is based onkirkwood_defconfig, but with a few other boards added which claim to beMULTI_v5.Signed-off-by Andrew Lunn <[email protected]>How about making this a
multi_v4_v5_defconfig? We have a much smaller number of v4/v4t platforms (moxart, i.MX1) that are multiplatform capable or could besome so in the future (clps711x, gemini, at91rm9200, some s3c24xx, omap15xx, integrator) compared to the multitude of v5 platforms, so it might not be useful to start a separatemulti_v4_defconfig.
Quoted 4 lines
OTOH if there is a significant performance impact in enabling
CPU_32v4andCPU_32v4T, we probably want to keep them separate.Any opinions?
Other than ixp4xx, (nslu2, old gateworks boards) I'm hard pressed to think of anything v4* still in the wild possibly wanting to use mainline kernels.
I'd prefer to do multi_v5_defconfig and revise later if we find the extraordinary circumstance.
thx,
Jason.
Andrew Lunn
maintainerPATCH v2 21/23 ARM: MVEBU: Simplifiy headers and make local
In reply to Andrew Lunnkirkwood is very nearly fully DT. Remove most of the address definitions from the header files and make it a local header file.
v2
Squash in the patch which removed unneeded includes.
--- arch/arm/mach-mvebu/include/mach/bridge-regs.h | 85 --------------- arch/arm/mach-mvebu/include/mach/kirkwood.h | 142 ------------------------- arch/arm/mach-mvebu/kirkwood-pm.c | 2 +- arch/arm/mach-mvebu/kirkwood.c | 9 +- arch/arm/mach-mvebu/kirkwood.h | 22 ++++ 5 files changed, 26 insertions(+), 234 deletions(-) delete mode 100644 arch/arm/mach-mvebu/include/mach/bridge-regs.h delete mode 100644 arch/arm/mach-mvebu/include/mach/kirkwood.h create mode 100644 arch/arm/mach-mvebu/kirkwood.h
arch/arm/mach-mvebu/include/mach/bridge-regs.h deleted +0 -85
@@ -1,85 +0,0 @@ -/* -* arch/arm/mach-mvebu/include/mach/bridge-regs.h -* -* Mbus-L to Mbus Bridge Registers -* -* This file is licensed under the terms of the GNU General Public -* License version 2. This program is licensed "as is" without any -* warranty of any kind, whether express or implied. -*/ - -#ifndef __ASM_ARCH_BRIDGE_REGS_H -#define __ASM_ARCH_BRIDGE_REGS_H - -#include <mach/kirkwood.h> - -#define CPU_CONFIG (BRIDGE_VIRT_BASE + 0x0100) -#define CPU_CONFIG_PHYS (BRIDGE_PHYS_BASE + 0x0100) -#define CPU_CONFIG_ERROR_PROP 0x00000004 - -#define CPU_CONTROL (BRIDGE_VIRT_BASE + 0x0104) -#define CPU_CONTROL_PHYS (BRIDGE_PHYS_BASE + 0x0104) -#define CPU_RESET 0x00000002 - -#define RSTOUTn_MASK (BRIDGE_VIRT_BASE + 0x0108) -#define SOFT_RESET_OUT_EN 0x00000004 - -#define SYSTEM_SOFT_RESET (BRIDGE_VIRT_BASE + 0x010c) -#define SOFT_RESET 0x00000001 - -#define BRIDGE_CAUSE (BRIDGE_VIRT_BASE + 0x0110) - -#define BRIDGE_INT_TIMER1_CLR (~0x0004) - -#define IRQ_VIRT_BASE (BRIDGE_VIRT_BASE + 0x0200) -#define IRQ_CAUSE_LOW_OFF 0x0000 -#define IRQ_MASK_LOW_OFF 0x0004 -#define IRQ_CAUSE_HIGH_OFF 0x0010 -#define IRQ_MASK_HIGH_OFF 0x0014 - -#define TIMER_VIRT_BASE (BRIDGE_VIRT_BASE + 0x0300) -#define TIMER_PHYS_BASE (BRIDGE_PHYS_BASE + 0x0300) - -#define L2_CONFIG_REG (BRIDGE_VIRT_BASE + 0x0128) -#define L2_WRITETHROUGH 0x00000010 - -#define CLOCK_GATING_CTRL (BRIDGE_VIRT_BASE + 0x11c) -#define CGC_BIT_GE0 (0) -#define CGC_BIT_PEX0 (2) -#define CGC_BIT_USB0 (3) -#define CGC_BIT_SDIO (4) -#define CGC_BIT_TSU (5) -#define CGC_BIT_DUNIT (6) -#define CGC_BIT_RUNIT (7) -#define CGC_BIT_XOR0 (8) -#define CGC_BIT_AUDIO (9) -#define CGC_BIT_SATA0 (14) -#define CGC_BIT_SATA1 (15) -#define CGC_BIT_XOR1 (16) -#define CGC_BIT_CRYPTO (17) -#define CGC_BIT_PEX1 (18) -#define CGC_BIT_GE1 (19) -#define CGC_BIT_TDM (20) -#define CGC_GE0 (1 << 0) -#define CGC_PEX0 (1 << 2) -#define CGC_USB0 (1 << 3) -#define CGC_SDIO (1 << 4) -#define CGC_TSU (1 << 5) -#define CGC_DUNIT (1 << 6) -#define CGC_RUNIT (1 << 7) -#define CGC_XOR0 (1 << 8) -#define CGC_AUDIO (1 << 9) -#define CGC_POWERSAVE (1 << 11) -#define CGC_SATA0 (1 << 14) -#define CGC_SATA1 (1 << 15) -#define CGC_XOR1 (1 << 16) -#define CGC_CRYPTO (1 << 17) -#define CGC_PEX1 (1 << 18) -#define CGC_GE1 (1 << 19) -#define CGC_TDM (1 << 20) -#define CGC_RESERVED (0x6 << 21) - -#define MEMORY_PM_CTRL (BRIDGE_VIRT_BASE + 0x118) -#define MEMORY_PM_CTRL_PHYS (BRIDGE_PHYS_BASE + 0x118) - -#endif
arch/arm/mach-mvebu/include/mach/kirkwood.h deleted +0 -142
142 lines not on this page · raw message
arch/arm/mach-mvebu/kirkwood-pm.c +1 -1
@@ -17,7 +17,7 @@#include <linux/kernel.h> #include <linux/suspend.h> #include <linux/io.h> -#include <mach/bridge-regs.h> +#include "kirkwood.h" static void __iomem *ddr_operation_base;static void __iomem *memory_pm_ctrl;
arch/arm/mach-mvebu/kirkwood.c +3 -6
@@ -13,19 +13,16 @@#include <linux/clk.h> #include <linux/kernel.h> #include <linux/init.h> +#include <linux/mbus.h> #include <linux/of.h> #include <linux/of_address.h> #include <linux/of_net.h> #include <linux/of_platform.h> -#include <linux/dma-mapping.h> -#include <linux/irqchip.h> -#include <linux/kexec.h> +#include <linux/slab.h> #include <asm/hardware/cache-feroceon-l2.h> #include <asm/mach/arch.h> #include <asm/mach/map.h> -#include <mach/bridge-regs.h> -#include <plat/common.h> -#include <plat/pcie.h> +#include "kirkwood.h" #include "kirkwood-pm.h" #include "common.h"
arch/arm/mach-mvebu/kirkwood.h new file +22 -0
@@ -0,0 +1,22 @@ +/* +* arch/arm/mach-mvebu/kirkwood.h +* +* Generic definitions for Marvell Kirkwood SoC flavors: +* 88F6180, 88F6192 and 88F6281. +* +* This file is licensed under the terms of the GNU General Public +* License version 2. This program is licensed "as is" without any +* warranty of any kind, whether express or implied. +*/ + +#define KIRKWOOD_REGS_PHYS_BASE 0xf1000000 +#define DDR_PHYS_BASE (KIRKWOOD_REGS_PHYS_BASE + 0x00000) +#define BRIDGE_PHYS_BASE (KIRKWOOD_REGS_PHYS_BASE + 0x20000) + +#define DDR_OPERATION_BASE (DDR_PHYS_BASE + 0x1418) + +#define CPU_CONFIG_PHYS (BRIDGE_PHYS_BASE + 0x0100) +#define CPU_CONFIG_ERROR_PROP 0x00000004 + +#define CPU_CONTROL_PHYS (BRIDGE_PHYS_BASE + 0x0104) +#define MEMORY_PM_CTRL_PHYS (BRIDGE_PHYS_BASE + 0x0118)
Signature · 1 line
1.8.5.3
Andrew Lunn
maintainerPATCH v2 22/23 ARM: config: Add mvebu_v5_defconfig
In reply to Andrew LunnNow that there is both v5 and v7 systems in mach-mvebu, the mvebu_defconfig is not sufficient, since these systems cannot be combined. Add a v5 defconfig which is based on kirkwood_defconfig, but purely DT.
--- arch/arm/configs/mvebu_v5_defconfig | 166 ++++++++++++++++++++++++++++++++++++ 1 file changed, 166 insertions(+) create mode 100644 arch/arm/configs/mvebu_v5_defconfig
arch/arm/configs/mvebu_v5_defconfig new file +166 -0
@@ -0,0 +1,166 @@ +CONFIG_SYSVIPC=y +CONFIG_NO_HZ=y +CONFIG_HIGH_RES_TIMERS=y +CONFIG_LOG_BUF_SHIFT=19 +CONFIG_PROFILING=y +CONFIG_OPROFILE=y +CONFIG_KPROBES=y +CONFIG_MODULES=y +CONFIG_MODULE_UNLOAD=y +# CONFIG_BLK_DEV_BSG is not set +# CONFIG_ARCH_MULTI_V7 is not set +CONFIG_ARCH_MVEBU=y +CONFIG_MACH_KIRKWOOD=y +# CONFIG_CPU_FEROCEON_OLD_ID is not set +CONFIG_PCI_MVEBU=y +CONFIG_PREEMPT=y +CONFIG_AEABI=y +CONFIG_HIGHMEM=y +CONFIG_ZBOOT_ROM_TEXT=0x0 +CONFIG_ZBOOT_ROM_BSS=0x0 +CONFIG_CPU_FREQ=y +CONFIG_CPU_FREQ_STAT_DETAILS=y +CONFIG_CPU_FREQ_DEFAULT_GOV_ONDEMAND=y +CONFIG_CPU_IDLE=y +CONFIG_NET=y +CONFIG_PACKET=y +CONFIG_UNIX=y +CONFIG_INET=y +CONFIG_IP_MULTICAST=y +CONFIG_IP_PNP=y +CONFIG_IP_PNP_DHCP=y +CONFIG_IP_PNP_BOOTP=y +# CONFIG_IPV6 is not set +CONFIG_NET_PKTGEN=m +CONFIG_CFG80211=y +CONFIG_MAC80211=y +CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" +CONFIG_MTD=y +CONFIG_MTD_CMDLINE_PARTS=y +CONFIG_MTD_BLOCK=y +CONFIG_MTD_CFI=y +CONFIG_MTD_JEDECPROBE=y +CONFIG_MTD_CFI_ADV_OPTIONS=y +CONFIG_MTD_CFI_GEOMETRY=y +# CONFIG_MTD_MAP_BANK_WIDTH_4 is not set +CONFIG_MTD_CFI_INTELEXT=y +CONFIG_MTD_CFI_STAA=y +CONFIG_MTD_PHYSMAP=y +CONFIG_MTD_M25P80=y +CONFIG_MTD_NAND=y +CONFIG_MTD_NAND_ORION=y +CONFIG_BLK_DEV_LOOP=y +CONFIG_EEPROM_AT24=y +# CONFIG_SCSI_PROC_FS is not set +CONFIG_BLK_DEV_SD=y +CONFIG_BLK_DEV_SR=m +CONFIG_CHR_DEV_SG=m +CONFIG_ATA=y +CONFIG_SATA_AHCI=y +CONFIG_SATA_MV=y +CONFIG_NETDEVICES=y +CONFIG_NET_DSA_MV88E6123_61_65=y +CONFIG_MV643XX_ETH=y +CONFIG_R8169=y +CONFIG_MARVELL_PHY=y +CONFIG_LIBERTAS=y +CONFIG_LIBERTAS_SDIO=y +CONFIG_INPUT_EVDEV=y +CONFIG_KEYBOARD_GPIO=y +# CONFIG_INPUT_MOUSE is not set +CONFIG_LEGACY_PTY_COUNT=16 +# CONFIG_DEVKMEM is not set +CONFIG_SERIAL_8250=y +CONFIG_SERIAL_8250_CONSOLE=y +CONFIG_SERIAL_8250_RUNTIME_UARTS=2 +CONFIG_SERIAL_OF_PLATFORM=y +# CONFIG_HW_RANDOM is not set +CONFIG_I2C=y +# CONFIG_I2C_COMPAT is not set +CONFIG_I2C_CHARDEV=y +CONFIG_I2C_MV64XXX=y +CONFIG_SPI=y +CONFIG_SPI_ORION=y +CONFIG_GPIO_SYSFS=y +CONFIG_SENSORS_ADT7475=y +CONFIG_SENSORS_LM63=y +CONFIG_SENSORS_LM75=y +CONFIG_SENSORS_LM85=y +CONFIG_THERMAL=y +CONFIG_WATCHDOG=y +CONFIG_HID_DRAGONRISE=y +CONFIG_HID_GYRATION=y +CONFIG_HID_TWINHAN=y +CONFIG_HID_NTRIG=y +CONFIG_HID_PANTHERLORD=y +CONFIG_HID_PETALYNX=y +CONFIG_HID_SAMSUNG=y +CONFIG_HID_SONY=y +CONFIG_HID_SUNPLUS=y +CONFIG_HID_GREENASIA=y +CONFIG_HID_SMARTJOYPLUS=y +CONFIG_HID_TOPSEED=y +CONFIG_HID_THRUSTMASTER=y +CONFIG_HID_ZEROPLUS=y +CONFIG_USB=y +CONFIG_USB_XHCI_HCD=y +CONFIG_USB_EHCI_HCD=y +CONFIG_USB_EHCI_ROOT_HUB_TT=y +CONFIG_USB_PRINTER=m +CONFIG_USB_STORAGE=y +CONFIG_USB_STORAGE_DATAFAB=y +CONFIG_USB_STORAGE_FREECOM=y +CONFIG_USB_STORAGE_SDDR09=y +CONFIG_USB_STORAGE_SDDR55=y +CONFIG_USB_STORAGE_JUMPSHOT=y +CONFIG_MMC=y +CONFIG_SDIO_UART=y +CONFIG_MMC_MVSDIO=y +CONFIG_NEW_LEDS=y +CONFIG_LEDS_CLASS=y +CONFIG_LEDS_GPIO=y +CONFIG_LEDS_TRIGGERS=y +CONFIG_LEDS_TRIGGER_TIMER=y +CONFIG_LEDS_TRIGGER_HEARTBEAT=y +CONFIG_LEDS_TRIGGER_DEFAULT_ON=y +CONFIG_RTC_CLASS=y +CONFIG_RTC_DRV_RS5C372=y +CONFIG_RTC_DRV_PCF8563=y +CONFIG_RTC_DRV_S35390A=y +CONFIG_RTC_DRV_MV=y +CONFIG_DMADEVICES=y +CONFIG_MV_XOR=y +CONFIG_EXT2_FS=y +CONFIG_EXT3_FS=y +# CONFIG_EXT3_FS_XATTR is not set +CONFIG_EXT4_FS=y +CONFIG_ISO9660_FS=m +CONFIG_JOLIET=y +CONFIG_UDF_FS=m +CONFIG_MSDOS_FS=y +CONFIG_VFAT_FS=y +CONFIG_TMPFS=y +CONFIG_JFFS2_FS=y +CONFIG_CRAMFS=y +CONFIG_NFS_FS=y +CONFIG_ROOT_NFS=y +CONFIG_NLS_CODEPAGE_437=y +CONFIG_NLS_CODEPAGE_850=y +CONFIG_NLS_ISO8859_1=y +CONFIG_NLS_ISO8859_2=y +CONFIG_NLS_UTF8=y +CONFIG_DEBUG_INFO=y +CONFIG_DEBUG_FS=y +CONFIG_MAGIC_SYSRQ=y +CONFIG_DEBUG_KERNEL=y +# CONFIG_SCHED_DEBUG is not set +# CONFIG_DEBUG_PREEMPT is not set +# CONFIG_FTRACE is not set +CONFIG_DEBUG_USER=y +CONFIG_DEBUG_LL=y +CONFIG_CRYPTO_CBC=m +CONFIG_CRYPTO_PCBC=m +# CONFIG_CRYPTO_ANSI_CPRNG is not set +CONFIG_CRYPTO_DEV_MV_CESA=y +CONFIG_CRC_CCITT=y +CONFIG_LIBCRC32C=y
Signature · 1 line
1.8.5.3
PATCH v2 22/23 ARM: config: Add mvebu_v5_defconfig
Andrew,
Quoted 17 lines · Andrew Lunn
Now that there is both v5 and v7 systems in mach-mvebu, the
mvebu_defconfigis not sufficient, since these systems cannot be combined. Add a v5 defconfig which is based onkirkwood_defconfig, but purely DT.Signed-off-by Andrew Lunn <[email protected]>--- arch/arm/configs/mvebu_v5_defconfig | 166 ++++++++++++++++++++++++++++++++++++ 1 file changed, 166 insertions(+) create mode 100644 arch/arm/configs/mvebu_v5_defconfigarch/arm/configs/mvebu_v5_defconfig new file +0
-0
arch/arm/configs/mvebu_v5_defconfig line 6
Quoted 6 lines
arch/arm/configs/mvebu_v5_defconfig new file +6
-0@@ -0,0 +1,166 @@ +CONFIG_SYSVIPC=y +CONFIG_NO_HZ=y +CONFIG_HIGH_RES_TIMERS=y +CONFIG_LOG_BUF_SHIFT=19 +CONFIG_PROFILING=y +CONFIG_OPROFILE=y
You're missing CONFIG_ORION_WATCHDOG=y, probably because it doesn't build in v3.14-rc1 on ARCH_MVEBU.
I think it's safe to add it to the defconfig, so once the watchdog MVEBU changes are merged, it'll get selected.
Signature · 3 lines
Ezequiel Garc?a, Free Electrons Embedded Linux, Kernel and Android Engineering http://free-electrons.com
Andrew Lunn
maintainerPATCH v2 23/23 ARM: Kirkwood: Remove DT support
In reply to Andrew LunnNow that all the device tree support is in mach-mvebu, remove it from mach-kirkwood.
Regenerate kirkwood_defconfig, removing all DT support, and a couple of other redundent options have been removed in the process.
--- arch/arm/configs/kirkwood_defconfig | 6 - arch/arm/mach-kirkwood/Kconfig | 18 --- arch/arm/mach-kirkwood/Makefile | 2 - arch/arm/mach-kirkwood/board-dt.c | 227 ------------------------------------ 4 files changed, 253 deletions(-) delete mode 100644 arch/arm/mach-kirkwood/board-dt.c
arch/arm/configs/kirkwood_defconfig +0 -6
@@ -20,13 +20,9 @@ CONFIG_MACH_RD88F6281=y CONFIG_MACH_T5325=y CONFIG_MACH_TS219=y CONFIG_MACH_TS41X=y -CONFIG_ARCH_KIRKWOOD_DT=y -CONFIG_MACH_MV88F6281GTW_GE_DT=y # CONFIG_CPU_FEROCEON_OLD_ID is not set -CONFIG_PCI_MVEBU=y CONFIG_PREEMPT=y CONFIG_AEABI=y -# CONFIG_OABI_COMPAT is not set CONFIG_HIGHMEM=y CONFIG_ZBOOT_ROM_TEXT=0x0 CONFIG_ZBOOT_ROM_BSS=0x0
@@ -85,7 +81,6 @@ CONFIG_LEGACY_PTY_COUNT=16 CONFIG_SERIAL_8250=y CONFIG_SERIAL_8250_CONSOLE=y CONFIG_SERIAL_8250_RUNTIME_UARTS=2 -CONFIG_SERIAL_OF_PLATFORM=y # CONFIG_HW_RANDOM is not set CONFIG_I2C=y # CONFIG_I2C_COMPAT is not set
@@ -176,5 +171,4 @@ CONFIG_CRYPTO_PCBC=m # CONFIG_CRYPTO_ANSI_CPRNG is not set CONFIG_CRYPTO_DEV_MV_CESA=y CONFIG_CRC_CCITT=y -CONFIG_CRC16=y CONFIG_LIBCRC32C=y
arch/arm/mach-kirkwood/Kconfig +0 -18
@@ -88,24 +88,6 @@ config MACH_TS41X QNAP TS-410, TS-410U, TS-419P, TS-419P+ and TS-419U Turbo NAS devices. -comment "Device tree entries" - -config ARCH_KIRKWOOD_DT - bool "Marvell Kirkwood Flattened Device Tree" - select KIRKWOOD_CLK - select OF_IRQ - select ORION_IRQCHIP - select ORION_TIMER - select POWER_SUPPLY - select POWER_RESET - select POWER_RESET_GPIO - select REGULATOR - select REGULATOR_FIXED_VOLTAGE - select USE_OF - help - Say 'Y' here if you want your kernel to support the - Marvell Kirkwood using flattened device tree. - endmenu endif
arch/arm/mach-kirkwood/Makefile +0 -2
@@ -10,5 +10,3 @@ obj-$(CONFIG_MACH_RD88F6281) += rd88f6281-setup.o obj-$(CONFIG_MACH_T5325) += t5325-setup.o obj-$(CONFIG_MACH_TS219) += ts219-setup.o tsx1x-common.o obj-$(CONFIG_MACH_TS41X) += ts41x-setup.o tsx1x-common.o - -obj-$(CONFIG_ARCH_KIRKWOOD_DT) += board-dt.o
arch/arm/mach-kirkwood/board-dt.c deleted +0 -227
227 lines not on this page · raw message
Signature · 1 line
1.8.5.3
Andrew Lunn
maintainerv2 cover Move DT kirkwood into mach-mvebu
In reply to Andrew LunnQuoted 4 lines · Andrew Lunn
The process of making most kirkwood boards boot using DT is nearly complete. We can now move these boards into mach-mvebu, freeing them of the legacy code needed for none-DT systems. At the same time, they can become part of
ARCH_MULTI_V5.
Patchset can also be found in
https://github.com/lunn/linux.git v3.14-rc1-mvebu-v2
Andrew
Arnd Bergmann
maintainerv2 cover Move DT kirkwood into mach-mvebu
In reply to Andrew LunnQuoted 4 lines · On Saturday 15 February 2014 11:19:58 Andrew Lunn wrote:
The process of making most kirkwood boards boot using DT is nearly complete. We can now move these boards into mach-mvebu, freeing them of the legacy code needed for none-DT systems. At the same time, they can become part of
ARCH_MULTI_V5.
Great to see this happening at last, great work everyone who was involved!
Feel free to add 'Acked-by: Arnd Bergmann <[email protected]>' to all patches I didn't comment on.
Arnd
v2 cover Move DT kirkwood into mach-mvebu
In reply to Andrew LunnQuoted 4 lines · Andrew Lunn
The process of making most kirkwood boards boot using DT is nearly complete. We can now move these boards into mach-mvebu, freeing them of the legacy code needed for none-DT systems. At the same time, they can become part of
ARCH_MULTI_V5.
Do you have a GIT URL for this? I can test it if you make it easy :)
Thanks,
Jason
v2 cover Move DT kirkwood into mach-mvebu
Quoted 7 lines · Jason Gunthorpe
Quoted 4 lines · Andrew Lunn
The process of making most kirkwood boards boot using DT is nearly complete. We can now move these boards into mach-mvebu, freeing them of the legacy code needed for none-DT systems. At the same time, they can become part of
ARCH_MULTI_V5.Do you have a GIT URL for this? I can test it if you make it easy :)
I believe this is it (web):
https://github.com/lunn/linux/tree/v3.14-rc1-mvebu-v2
so git ...
https://github.com/lunn/linux.git v3.14-rc1-mvebu-v2
hth,
Jason.
v2 cover Move DT kirkwood into mach-mvebu
Quoted 7 lines · Jason Cooper
Quoted 6 lines · Jason Gunthorpe
Quoted 4 lines · Andrew Lunn
The process of making most kirkwood boards boot using DT is nearly complete. We can now move these boards into mach-mvebu, freeing them of the legacy code needed for none-DT systems. At the same time, they can become part of
ARCH_MULTI_V5.
Quoted 5 lines
Quoted 1 line
Do you have a GIT URL for this? I can test it if you make it easy :)
I believe this is it (web):
Thanks, I tested v3 of the patchset.
It boots, but I can't do very much because the watchdog driver doesn't build and my system is configured to watchdog timeout if there is no watchdog driver.
Presumably the watchdog patchset needs to be a dependency for this? Is there a git URL for it?
Also, reviewing my 3.13 Kconfig vs the 3.14 Kconfig with the patch, these options are now forced on, and I'd prefer them to be off:
CONFIG_ARM_PATCH_PHYS_VIRT=y
CONFIG_GENERIC_PHY=y
CONFIG_PHY_MVEBU_SATA=y
And looking at the final kconfig directly a bit:
config ARCH_MVEBU
bool "Marvell SOCs with Device Tree support" if (ARCH_MULTI_V7 || ARCH_MULTI_V5) select ARCH_SUPPORTS_BIG_ENDIAN
select CLKSRC_MMIO
select COMMON_CLK
select GENERIC_CLOCKEVENTS
select GENERIC_IRQ_CHIP
select IRQ_DOMAIN
select MULTI_IRQ_HANDLER
select PINCTRL
select PLAT_ORION
select SPARSE_IRQ
select CLKDEV_LOOKUP
select MVEBU_MBUS
select ZONE_DMA if ARM_LPAE
select ARCH_REQUIRE_GPIOLIB
select MIGHT_HAVE_PCI
select PCI_QUIRKS if PCI
^^^^^^^^^^^^^^^^^^^
This can go now, it was something I added to support the old
non-dt kirkwood PCI-E driver. The new DT MVEBU driver does not require it.
config MACH_KIRKWOOD
bool "Marvell Kirkwood boards" if ARCH_MULTI_V5 select ARCH_HAS_CPUFREQ
select ARCH_REQUIRE_GPIOLIB
select CPU_FEROCEON
select KIRKWOOD_CLK
select OF_IRQ
select ORION_IRQCHIP
select ORION_TIMER
select PCI
select PCI_QUIRKS
^^^^^
Also unecessary, see above
select PINCTRL_KIRKWOOD
select POWER_SUPPLY
select POWER_RESET
select POWER_RESET_GPIO
select REGULATOR
select REGULATOR_FIXED_VOLTAGE
select USE_OF
And I feel PCI, POWER_SUPPLY, POWER_RESET, POWER_RESET_GPIO, REGULATOR, REGULATOR_FIXED_VOLTAGE should not be forced in the master KConfig as not all boards require them.
Maybe make them forced if !EMBEDDED or something?
Shouldn't USE_OF and OF_IRQ be in ARCH_MVEBU?
These options were also switched on, but I have no opinion on them.. :)
CONFIG_SPARSE_IRQ is now mandatory CONFIG_ARCH_USE_BUILTIN_BSWAP is turned on CONFIG_HAVE_CC_STACKPROTECTOR and related are on CONFIG_NO_BOOTMEM=y
CONFIG_AUTO_ZRELADDR=y
Jason
Andrew Lunn
maintainerv2 cover Move DT kirkwood into mach-mvebu
Quoted 1 line
Thanks, I tested v3 of the patchset.
Great, thanks.
Quoted 6 lines
It boots, but I can't do very much because the watchdog driver doesn't build and my system is configured to watchdog timeout if there is no watchdog driver.
Presumably the watchdog patchset needs to be a dependency for this? Is there a git URL for it?
I don't have a tree with both combined. I guess there is a branch in
https://github.com/MISL-EBU-System-SW/mainline-public.git
with it.
Quoted 3 lines
Also, reviewing my 3.13
Kconfigvs the 3.14Kconfigwith the patch, these options are now forced on, and I'd prefer them to be off:
CONFIG_ARM_PATCH_PHYS_VIRT=y
I suspect that comes from multiplatform.
Quoted 2 lines
CONFIG_GENERIC_PHY=y
CONFIG_PHY_MVEBU_SATA=y
If you disable SATA, you can disable these two. We have had so much breakage with this, that i want to keep away from it for a while to let it settle. I can then go back and see about making it truly optional.
Quoted 16 lines
And looking at the final kconfig directly a bit:
config
ARCH_MVEBU
bool "Marvell SOCs with Device Tree support" if (ARCH_MULTI_V7||ARCH_MULTI_V5) selectARCH_SUPPORTS_BIG_ENDIAN
selectCLKSRC_MMIO
selectCOMMON_CLK
selectGENERIC_CLOCKEVENTS
selectGENERIC_IRQ_CHIP
selectIRQ_DOMAIN
selectMULTI_IRQ_HANDLER
select PINCTRL
selectPLAT_ORION
selectSPARSE_IRQ
selectCLKDEV_LOOKUP
selectMVEBU_MBUS
Quoted 8 lines
select
ZONE_DMAifARM_LPAE
selectARCH_REQUIRE_GPIOLIB
selectMIGHT_HAVE_PCI
selectPCI_QUIRKSif PCI
^^^^^^^^^^^^^^^^^^^
This can go now, it was something I added to support the old non-dt kirkwood PCI-E driver. The new DT MVEBU driver does not require it.
This has nothing directly to do with this patchset. Please could you supply a patch?
Quoted 22 lines
config
MACH_KIRKWOOD
bool "Marvell Kirkwood boards" ifARCH_MULTI_V5selectARCH_HAS_CPUFREQ
selectARCH_REQUIRE_GPIOLIB
selectCPU_FEROCEON
selectKIRKWOOD_CLK
selectOF_IRQ
selectORION_IRQCHIP
selectORION_TIMERselect PCI
selectPCI_QUIRKS
^^^^^
Also unecessary, see above
selectPINCTRL_KIRKWOOD
selectPOWER_SUPPLY
selectPOWER_RESET
selectPOWER_RESET_GPIO
select REGULATOR
selectREGULATOR_FIXED_VOLTAGE
selectUSE_OF
Quoted 3 lines
And I feel PCI,
POWER_SUPPLY,POWER_RESET,POWER_RESET_GPIO, REGULATOR,REGULATOR_FIXED_VOLTAGEshould not be forced in the master KConfig as not all boards require them.
At the moment, we need PCI in order to get the SoC ID. Gregory has a patch which will help with this, only selecting the minimum needed. However, ARCH_KIRKWOOD selected both PCI and PCI_QUIRKS, so i think removing them should be in a separate cleanup patch, which can follow once the series is accepted. I added the POWER_* and REGULATOR_* options. I will move them into mvebu_v5_defconfig and multi_v5_defconfig instead.
Quoted 1 line
Maybe make them forced if !EMBEDDED or something?
I think we first need to define what EMBEDDED means. For me a NAS is an embedded system, and it is various NAS boxes which want these.
Quoted 1 line
Shouldn't
USE_OFandOF_IRQbe inARCH_MVEBU?
Probably. I'm guessing the others are getting these from multi_v7_defconfig. I would say this again is something for a cleanup patch once the series is merged. Dove is also not too far away from moving in, so i think it makes sense to look at things like this once we have the complete picture.
Andrew
v2 cover Move DT kirkwood into mach-mvebu
Quoted 8 lines · Andrew Lunn
Quoted 2 lines
Presumably the watchdog patchset needs to be a dependency for this? Is there a git URL for it?
I don't have a tree with both combined. I guess there is a branch in
https://github.com/MISL-EBU-System-SW/mainline-public.git
with it.
Thanks, I'll take a peek
Quoted 5 lines
Quoted 3 lines
Also, reviewing my 3.13
Kconfigvs the 3.14Kconfigwith the patch, these options are now forced on, and I'd prefer them to be off:
CONFIG_ARM_PATCH_PHYS_VIRT=yI suspect that comes from multiplatform.
Right
Quoted 7 lines
Quoted 2 lines
CONFIG_GENERIC_PHY=y
CONFIG_PHY_MVEBU_SATA=yIf you disable SATA, you can disable these two. We have had so much breakage with this, that i want to keep away from it for a while to let it settle. I can then go back and see about making it truly optional.
No, I have SATA off, it is being selected unconditionally:
config PHY_MVEBU_SATA
def_bool y
depends on ARCH_KIRKWOOD || ARCH_DOVE || MACH_KIRKWOOD depends on OF
select GENERIC_PHY
Does it need 'depends on ATA'?
Quoted 8 lines
Quoted 5 lines
select
PCI_QUIRKSif PCI
^^^^^^^^^^^^^^^^^^^
This can go now, it was something I added to support the old non-dt kirkwood PCI-E driver. The new DT MVEBU driver does not require it.This has nothing directly to do with this patchset. Please could you supply a patch?
Sure, when your patchset is merged I can look at the QUIRKS setting for mvebu
Quoted 5 lines
Quoted 3 lines
And I feel PCI,
POWER_SUPPLY,POWER_RESET,POWER_RESET_GPIO, REGULATOR,REGULATOR_FIXED_VOLTAGEshould not be forced in the master KConfig as not all boards require them.At the moment, we need PCI in order to get the SoC ID.
So this is happening because mvebu-soc-id.c is being unconditionally compiled, even though it is not needed on anything except armada-370-xp ?
Quoted 4 lines
Gregory has a patch which will help with this, only selecting the minimum needed. However,
ARCH_KIRKWOODselected both PCI andPCI_QUIRKS, so i think removing them should be in a separate cleanup patch, which can follow once the series is accepted.
Agree
Quoted 2 lines
I added the POWER_* and REGULATOR_* options. I will move them into
mvebu_v5_defconfigandmulti_v5_defconfiginstead.
Thanks
Quoted 4 lines
Quoted 1 line
Maybe make them forced if !EMBEDDED or something?
I think we first need to define what EMBEDDED means. For me a NAS is an embedded system, and it is various NAS boxes which want these.
EMBEDDED is just a master option to expose KConfig choices that normal people wouldn't want to mess with (eg the ability to disable REGULATOR). It seems to have fallen out of favor these days I guess, maybe EXPERT is the way to go now?
Jason
v2 cover Move DT kirkwood into mach-mvebu
In reply to Jason GunthorpeQuoted 14 lines · Jason Gunthorpe
Quoted 7 lines · Jason Cooper
Quoted 6 lines · Jason Gunthorpe
Quoted 4 lines · Andrew Lunn
The process of making most kirkwood boards boot using DT is nearly complete. We can now move these boards into mach-mvebu, freeing them of the legacy code needed for none-DT systems. At the same time, they can become part of
ARCH_MULTI_V5.Quoted 5 lines
Quoted 1 line
Do you have a GIT URL for this? I can test it if you make it easy :)
I believe this is it (web):
Quoted 9 lines
Thanks, I tested v3 of the patchset.
It boots, but I can't do very much because the watchdog driver doesn't build and my system is configured to watchdog timeout if there is no watchdog driver.
Presumably the watchdog patchset needs to be a dependency for this? Is there a git URL for it?
I can take a look at preparing a merged branch for this today. Or at least making sure the watchdog branches in mvebu, merge cleanly with this.
After all, I also wanted to give this work a test... :)
Signature · 3 lines
Ezequiel Garc?a, Free Electrons Embedded Linux, Kernel and Android Engineering http://free-electrons.com
v2 cover Move DT kirkwood into mach-mvebu
In reply to Jason GunthorpeQuoted 14 lines · Jason Gunthorpe
Quoted 7 lines · Jason Cooper
Quoted 6 lines · Jason Gunthorpe
Quoted 4 lines · Andrew Lunn
The process of making most kirkwood boards boot using DT is nearly complete. We can now move these boards into mach-mvebu, freeing them of the legacy code needed for none-DT systems. At the same time, they can become part of
ARCH_MULTI_V5.Quoted 5 lines
Quoted 1 line
Do you have a GIT URL for this? I can test it if you make it easy :)
I believe this is it (web):
Quoted 9 lines
Thanks, I tested v3 of the patchset.
It boots, but I can't do very much because the watchdog driver doesn't build and my system is configured to watchdog timeout if there is no watchdog driver.
Presumably the watchdog patchset needs to be a dependency for this? Is there a git URL for it?
Andrew's v3 and the mvebu/watchdog branch merges without any conflicts:
https://github.com/lunn/linux/tree/v3.14-rc1-mvebu-v3
http://git.infradead.org/linux-mvebu.git/shortlog/refs/heads/mvebu/watchdog
And multi v5 works great here!
Signature · 3 lines
Ezequiel Garc?a, Free Electrons Embedded Linux, Kernel and Android Engineering http://free-electrons.com
Andrew Lunn
maintainerv2 cover Move DT kirkwood into mach-mvebu
Quoted 7 lines
Andrew's v3 and the mvebu/watchdog branch merges without any conflicts:
https://github.com/lunn/linux/tree/v3.14-rc1-mvebu-v3
http://git.infradead.org/linux-mvebu.git/shortlog/refs/heads/mvebu/watchdog
And multi v5 works great here!
Great, thanks for testing. I will add back the CONFIG for the watchdog.
Andrew
v2 cover Move DT kirkwood into mach-mvebu
In reply to Ezequiel GarciaQuoted 10 lines · Ezequiel Garcia
Quoted 9 lines
Thanks, I tested v3 of the patchset.
It boots, but I can't do very much because the watchdog driver doesn't build and my system is configured to watchdog timeout if there is no watchdog driver.
Presumably the watchdog patchset needs to be a dependency for this? Is there a git URL for it?
Quoted 7 lines
Andrew's v3 and the mvebu/watchdog branch merges without any conflicts:
https://github.com/lunn/linux/tree/v3.14-rc1-mvebu-v3
http://git.infradead.org/linux-mvebu.git/shortlog/refs/heads/mvebu/watchdog
And multi v5 works great here!
It is working now for me as well, I haven't noticed any strangeness at least..
Ezequiel, after I applied your watchdog branch the .dtsi files lacked the new 2nd register:
wdt: watchdog-timer at 20300 {
compatible = "marvell,orion-wdt";
reg = <0x20300 0x28>;
interrupt-parent = <&bridge_intc>;
interrupts = <3>;
clocks = <&gate_clk 7>;
status = "okay";
};Which creates a nasty warn-on during boot - is that expected?
BTW, for both patche sets:
Also, there seems to be some missing request_region in drivers (can be fixedup later)
f1001418-f100141b : kirkwood_cpuidle
f1001500-f100151f : /mbus/internal at f1000000/mbus-controller at 20000 f1010030-f1010033 : /mbus/internal at f1000000/core-clocks at 10030 f1020000-f102007f : /mbus/internal at f1000000/mbus-controller at 20000 f1020104-f1020107 : kirkwood-cpufreq
f1020108-f102010b : /mbus/internal at f1000000/wdt at 20300 f102011c-f102011f : /mbus/internal at f1000000/clock-gating-control at 2011c f1020128-f102012b : /mbus/internal at f1000000/l2-cache at 20128 f1020300-f102031f : /mbus/internal at f1000000/timer at 20300 f1040000-f1041fff : /mbus/pex at e0000000/pcie at 1,0 f1072000-f1075fff : /mbus/internal at f1000000/egiga0
f1072004-f1072087 : /mbus/internal at f1000000/mdio at 72000
f4000000-f40003ff : /mbus/nand at f4000000/nand at 0
In general it should be:
f1012100-f10121ff : /mbus/internal at f1000000/serial at 12100 (<-- OF stanza)
f1012100-f101211f : serial (<-- Driver request region)
Jason
v2 cover Move DT kirkwood into mach-mvebu
Quoted 34 lines · Jason Gunthorpe
Quoted 10 lines · Ezequiel Garcia
Quoted 9 lines
Thanks, I tested v3 of the patchset.
It boots, but I can't do very much because the watchdog driver doesn't build and my system is configured to watchdog timeout if there is no watchdog driver.
Presumably the watchdog patchset needs to be a dependency for this? Is there a git URL for it?
Quoted 7 lines
Andrew's v3 and the mvebu/watchdog branch merges without any conflicts:
https://github.com/lunn/linux/tree/v3.14-rc1-mvebu-v3
http://git.infradead.org/linux-mvebu.git/shortlog/refs/heads/mvebu/watchdog
And multi v5 works great here!
It is working now for me as well, I haven't noticed any strangeness at least..
Ezequiel, after I applied your watchdog branch the .dtsi files lacked the new 2nd register:
wdt: watchdog-timer at 20300 { compatible = "marvell,orion-wdt"; reg = <0x20300 0x28>; interrupt-parent = <&bridge_intc>; interrupts = <3>; clocks = <&gate_clk 7>; status = "okay"; };
Quoted 2 lines
Which creates a nasty warn-on during boot - is that expected?
Yup, that's expected. It avoids any backwards compatibility issues. The watchdog patchset has been pulled by Jason Cooper in two branches; if my memory doesn't fail me, they are: mvebu/watchdog and mvebu/dt.
However, the mvebu/dt branch seemed to conflict with Andrew's multi-v5 work, so I haven't advised you to merge it as well. And since the watchdog can work with the old DT, it's not a big issue.
Just remember to update your DTB.
Quoted 3 lines
BTW, for both patche sets:
Thanks! The watchdog work is already merged, but maybe Jason Cooper can take care of adding your tested-by.
Signature · 3 lines
Ezequiel Garc?a, Free Electrons Embedded Linux, Kernel and Android Engineering http://free-electrons.com
v2 cover Move DT kirkwood into mach-mvebu
Quoted 1 line · Ezequiel Garcia
On Fri, Feb 21, 2014 at 10:57:50AM -0700, Jason Gunthorpe wrote:
...
Quoted 6 lines
Quoted 3 lines
BTW, for both patche sets:
Thanks! The watchdog work is already merged, but maybe Jason Cooper can take care of adding your tested-by.
Done. Andrew, please add it to your series if/when there's a new version.
thx,
Jason.