dma: sdma: Add imx25 compatible
Subsystems (3)
PATCH 1/1 dma: sdma: Add imx25 compatible
imx25 did not work without a firmware previously.
This patch adds a DT compatible to pass the correct data with the default script addresses for imx25.
Add imx25 compatible to the list of compatibles in the binding documentation.
--- Documentation/devicetree/bindings/dma/fsl-imx-sdma.txt | 16 ++++++++++------ drivers/dma/imx-sdma.c | 1 + 2 files changed, 11 insertions(+), 6 deletions(-)
Documentation/devicetree/bindings/dma/fsl-imx-sdma.txt +10 -6
@@ -1,12 +1,16 @@ * Freescale Smart Direct Memory Access (SDMA) Controller for i.MX Required properties: -- compatible : Should be "fsl,imx31-sdma", "fsl,imx31-to1-sdma", - "fsl,imx31-to2-sdma", "fsl,imx35-sdma", "fsl,imx35-to1-sdma", - "fsl,imx35-to2-sdma", "fsl,imx51-sdma", "fsl,imx53-sdma" or - "fsl,imx6q-sdma". The -to variants should be preferred since they - allow to determnine the correct ROM script addresses needed for - the driver to work without additional firmware. +- compatible : Should be one of + "fsl,imx25-sdma" + "fsl,imx31-sdma", "fsl,imx31-to1-sdma", "fsl,imx31-to2-sdma" + "fsl,imx35-sdma", "fsl,imx35-to1-sdma", "fsl,imx35-to2-sdma" + "fsl,imx51-sdma" + "fsl,imx53-sdma" + "fsl,imx6q-sdma" + The -to variants should be preferred since they allow to determnine the + correct ROM script addresses needed for the driver to work without additional + firmware. - reg : Should contain SDMA registers location and length - interrupts : Should contain SDMA interrupt - #dma-cells : Must be <3>.
drivers/dma/imx-sdma.c +1 -0
@@ -449,6 +449,7 @@ static const struct of_device_id sdma_dt_ids[] = { { .compatible = "fsl,imx51-sdma", .data = &sdma_imx51, }, { .compatible = "fsl,imx35-sdma", .data = &sdma_imx35, }, { .compatible = "fsl,imx31-sdma", .data = &sdma_imx31, }, + { .compatible = "fsl,imx25-sdma", .data = &sdma_imx25, }, { /* sentinel */ } }; MODULE_DEVICE_TABLE(of, sdma_dt_ids);
Signature · 1 line
1.8.5.3
PATCH 1/1 dma: sdma: Add imx25 compatible
Quoted 9 lines · Markus Pargmann
imx25 did not work without a firmware previously.
This patch adds a DT compatible to pass the correct data with the default script addresses for imx25.
Add imx25 compatible to the list of compatibles in the binding documentation.
Signed-off-by Markus Pargmann <[email protected]>
PATCH 1/1 dma: sdma: Add imx25 compatible
In reply to Markus PargmannQuoted 9 lines · Markus Pargmann
imx25 did not work without a firmware previously.
This patch adds a DT compatible to pass the correct data with the default script addresses for imx25.
Add imx25 compatible to the list of compatibles in the binding documentation.
Signed-off-by Markus Pargmann <[email protected]>
Applie,d thanks
Signature · 1 line
~Vinod