board: Add support for B&R KWB Motherboard
PATCH 1/1 board: Add support for B&R KWB Motherboard
Adds support for Bernecker & Rainer Industrieelektronik GmbH KWB Motherboard, using TI's AM3352 SoC.
Most of code is derived from TI's AM335x_EVM
--- board/BuR/bur_kwb/Makefile | 16 ++ board/BuR/bur_kwb/am335xScreen.c | 548 ++++++++++++++++++++++++++++++++++++++ board/BuR/bur_kwb/am335xScreen.h | 45 ++++ board/BuR/bur_kwb/board.c | 522 ++++++++++++++++++++++++++++++++++++ board/BuR/bur_kwb/board.h | 18 ++ board/BuR/bur_kwb/mux.c | 213 +++++++++++++++ board/BuR/bur_kwb/u-boot.lds | 101 +++++++ boards.cfg | 1 + include/configs/bur_kwb.h | 352 ++++++++++++++++++++++++ 9 files changed, 1816 insertions(+) create mode 100644 board/BuR/bur_kwb/Makefile create mode 100644 board/BuR/bur_kwb/am335xScreen.c create mode 100644 board/BuR/bur_kwb/am335xScreen.h create mode 100644 board/BuR/bur_kwb/board.c create mode 100644 board/BuR/bur_kwb/board.h create mode 100644 board/BuR/bur_kwb/mux.c create mode 100644 board/BuR/bur_kwb/u-boot.lds create mode 100644 include/configs/bur_kwb.h
board/BuR/bur_kwb/Makefile new file +16 -0
@@ -0,0 +1,16 @@ +# +# Makefile +# +# Copyright (C) 2014 Hannes Petermaier <[email protected]> - +# Bernecker & Rainer Industrielektronik GmbH - http://www.br-automation.com/ +# +# SPDX-License-Identifier: GPL-2.0+ +# + +ifeq ($(CONFIG_SPL_BUILD),y) +obj-y := mux.o +endif +ifeq ($(CONFIG_SYS_SCREEN),y) +obj-y += am335xScreen.o +endif +obj-y += board.o
board/BuR/bur_kwb/am335xScreen.c new file +548 -0
548 lines not on this page · raw message
board/BuR/bur_kwb/am335xScreen.h new file +45 -0
45 lines not on this page · raw message
board/BuR/bur_kwb/board.c new file +522 -0
522 lines not on this page · raw message
board/BuR/bur_kwb/board.h new file +18 -0
@@ -0,0 +1,18 @@ +/* +* board.h +* +* BUR-KWB boards information header +* +* Copyright (C) 2013, Bernecker & Rainer Industrieelektronik GmbH - +* http://www.br-automation.com +* +* SPDX-License-Identifier: GPL-2.0+ +*/ + +#ifndef _BOARD_H_ +#define _BOARD_H_ + +void enable_uart0_pin_mux (void ); +void enable_i2c0_pin_mux (void ); +void enable_board_pin_mux (void ); +#endif
board/BuR/bur_kwb/mux.c new file +213 -0
213 lines not on this page · raw message
board/BuR/bur_kwb/u-boot.lds new file +101 -0
101 lines not on this page · raw message
boards.cfg +1 -0
@@ -255,6 +255,7 @@ Active arm armv7 am33xx phytec pcm051 Active arm armv7 am33xx siemens dxr2 dxr2 - Roger Meier <[email protected]> Active arm armv7 am33xx siemens pxm2 pxm2 - Roger Meier <[email protected]> Active arm armv7 am33xx siemens rut rut - Roger Meier <[email protected]> +Active arm armv7 am33xx BuR bur_kwb bur_kwb bur_kwb:SERIAL1,CONS_INDEX=1,EMMC_BOOT Hannes Petermaier <[email protected]> Active arm armv7 am33xx ti am335x am335x_boneblack am335x_evm:SERIAL1,CONS_INDEX=1,EMMC_BOOT Tom Rini <[email protected]> Active arm armv7 am33xx ti am335x am335x_evm am335x_evm:SERIAL1,CONS_INDEX=1,NAND Tom Rini <[email protected]> Active arm armv7 am33xx ti am335x am335x_evm_nor am335x_evm:SERIAL1,CONS_INDEX=1,NAND,NOR Tom Rini <[email protected]>
include/configs/bur_kwb.h new file +352 -0
352 lines not on this page · raw message
Signature · 1 line
1.7.9.5
PATCH 1/1 board: Add support for B&R KWB Motherboard
Quoted 11 lines · Hannes Petermaier
Adds support for Bernecker & Rainer Industrieelektronik GmbH KWB Motherboard, using TI's AM3352 SoC.
Most of code is derived from TI's
AM335x_EVMSigned-off-by Hannes Petermaier <[email protected]>Cc trini at ti.com--- board/BuR/bur_kwb/Makefile | 16 ++ board/BuR/bur_kwb/am335xScreen.c | 548 ++++++++++++++++++++++++++++++++++++++ board/BuR/bur_kwb/am335xScreen.h | 45 ++++
Minor nit, this should be am335x_screen.[ch]
board/BuR/bur_kwb/Makefile line 16
Quoted 7 lines
board/BuR/bur_kwb/Makefile new file +7
-0+ifeq ($(CONFIG_SPL_BUILD),y) +obj-y := mux.o +endif +ifeq ($(CONFIG_SYS_SCREEN),y) +obj-y += am335xScreen.o +endif +obj-y += board.o
obj-$(CONFIG_SPL_BUILD) +=
obj-$(CONFIG_SYS_SCREEN) +=
Quoted 1 line
board/BuR/bur_kwb/am335xScreen.c +0
-0
[snip]
Quoted 1 line
+#if
defined(CONFIG_SYS_SCREEN)&& !defined(CONFIG_SPL_BUILD)
You shouldn't need this. It'll be discarded if unused.
board/BuR/bur_kwb/am335xScreen.c line 43
Quoted 7 lines
board/BuR/bur_kwb/am335xScreen.c +7
-0+ +#define DEBUG +#ifdef DEBUG +#define DBG (...) printf(__VA_ARGS__) +#else +#define DBG (...) +#endif /* DEBUG */
We provide debug(...) already.
board/BuR/bur_kwb/am335xScreen.c line 46
Quoted 2 lines
board/BuR/bur_kwb/am335xScreen.c +2
-0+#define SCREEN_HMAX 1366 +#define SCREEN_VMAX 768
For consistency, please '#define<space>' globally, thanks.
Quoted 1 line
+static const unsigned char char_tab2[257*8] = {
A comment about what this is please.
board/BuR/bur_kwb/am335xScreen.c line 371
Quoted 10 lines
board/BuR/bur_kwb/am335xScreen.c +10
-0+static void setPix (struct screen_typ *pscr, +unsigned int x,unsigned int y,unsigned int color) +{ +unsigned int addroffset =0 ; + +/* braces not for function, only for better reading by human :-) */ + addroffset = y * (pscr->resx*4 ) + (x*4 ); + *(unsigned int *)(pscr->pfb+addroffset) = (color &0x00FFFFFF ); +} +static void outch(struct screen_typ *pscr,
Newline after functions, fix globally. Also set_pix(), etc, also fix globally.
Quoted 1 line
+++
b/board/BuR/bur_kwb/board.c
[snip]
board/BuR/bur_kwb/am335xScreen.c
Quoted 3 lines
board/BuR/bur_kwb/am335xScreen.c +3
-0+if (i2c_probe (TPS65217_CHIP_PM )) { +printf ("PMIC (0x%02x) not found! skip further initalization.\n" , +TPS65217_CHIP_PM );
You should be able to do this with puts() since it's all constants.
board/BuR/bur_kwb/am335xScreen.c
Quoted 11 lines
board/BuR/bur_kwb/am335xScreen.c +11
-0+/* +* Increase USB current limit to 1300mA or 1800mA and set +* the MPU voltage controller as needed. +*/ +if (dpll_mpu_opp100.m ==MPUPLL_M_1000 ) { + usb_cur_lim =TPS65217_USB_INPUT_CUR_LIMIT_1800MA ; + mpu_vdd =TPS65217_DCDC_VOLT_SEL_1325MV ; + }else { + usb_cur_lim =TPS65217_USB_INPUT_CUR_LIMIT_1300MA ; + mpu_vdd =TPS65217_DCDC_VOLT_SEL_1275MV ; + }
Since you've got a tps65217 (like beaglebone) you can drop the tps65250 include earlier in the file.
Quoted 1 line
+++
b/board/BuR/bur_kwb/u-boot.lds
Since you don't support NOR, you should be able to use the generic linker script.
Quoted 1 line
+++
b/include/configs/bur_kwb.h
[snip]
board/BuR/bur_kwb/am335xScreen.c
Quoted 10 lines
board/BuR/bur_kwb/am335xScreen.c +10
-0+#include <config_cmd_default.h> +/* -------------------------------------------------------------------------*/ +/* -- undefinig unused features -- */ +/* prior defined from config_defaults.h */ +#undef CONFIG_BOOTM_LINUX +#undef CONFIG_BOOTM_NETBSD +#undef CONFIG_BOOTM_PLAN9 +#undef CONFIG_BOOTM_RTEMS +#undef CONFIG_GZIP +#undef CONFIG_ZLIB
Space not tab please.
Quoted 1 line
+#define
CONFIG_SYS_NO_FLASH
Duplicate.
board/BuR/bur_kwb/am335xScreen.c
Quoted 2 lines
board/BuR/bur_kwb/am335xScreen.c +2
-0+/* MMC/SD IP block */ +#if defined(CONFIG_EMMC_BOOT )
So, CONFIG_EMMC_BOOT is used in am335x_evm.h since we have to support building for a few different variants. In this case it looks like you can just drop setting EMMC_BOOT in boards.cfg and then simplify a lot of the logic in the config file too.
Quoted 5 lines
+ #define
CONFIG_MMC
+ #defineCONFIG_GENERIC_MMC
+ #defineCONFIG_OMAP_HSMMC
+ #defineCONFIG_CMD_MMC
+ #defineCONFIG_SUPPORT_EMMC_BOOT
So, are you making use of 'mmc open' / 'mmc close' on this platform to work with the eMMC boot partitions today?
board/BuR/bur_kwb/am335xScreen.c
Quoted 11 lines
board/BuR/bur_kwb/am335xScreen.c +11
-0+/* +* Our platforms make use of SPL to initalize the hardware (primarily +* memory) enough for full U-Boot to be loaded. We also support Falcon +* Mode so that the Linux kernel can be booted directly from SPL +* instead, if desired. We make use of the general SPL framework found +* under common/spl/. Given our generally common memory map, we set a +* number of related defaults and sizes here. +*/ +#define CONFIG_SPL +#define CONFIG_SPL_FRAMEWORK +#undef CONFIG_SPL_OS_BOOT
Just don't set CONFIG_SPL_OS_BOOT, and drop the function from board.c that you've got too.
board/BuR/bur_kwb/am335xScreen.c
Quoted 6 lines
board/BuR/bur_kwb/am335xScreen.c +6
-0+#define CONFIG_SYS_NS16550_COM1 0x44e09000/* Base EVM has UART0 */ +#define CONFIG_SYS_NS16550_COM2 0x48022000/* UART1 */ +#define CONFIG_SYS_NS16550_COM3 0x48024000/* UART2 */ +#define CONFIG_SYS_NS16550_COM4 0x481a6000/* UART3 */ +#define CONFIG_SYS_NS16550_COM5 0x481a8000/* UART4 */ +#define CONFIG_SYS_NS16550_COM6 0x481aa000/* UART5 */
Do you use / care about all uarts?
And it looks like there's other parts of the config file that could be cleaned up a bit too. Perhaps you can leverage include/configs/ti_armv7_common.h ? If not, I'd really like to hear about the shortcomings there as one of the goals with it is to make adding new boards easier and have a smaller code footprint.
Thanks!
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: not available Type: application/pgp-signature Size: 836 bytes Desc: Digital signature URL: <http://lists.denx.de/pipermail/u-boot/attachments/20140205/5e53f258/attachment.pgp>
PATCH 1/1 board: Add support for B&R KWB Motherboard
In reply to Hannes PetermaierDear Hannes,
Quoted 7 lines · In message <[email protected]> you wrote:
Adds support for Bernecker & Rainer Industrieelektronik GmbH KWB Motherboard, using TI's AM3352 SoC.
Most of code is derived from TI's
AM335x_EVMSigned-off-by Hannes Petermaier <[email protected]>Cc trini at ti.com
Quoted 8 lines
--- board/BuR/bur_kwb/Makefile | 16 ++ board/BuR/bur_kwb/am335xScreen.c | 548 ++++++++++++++++++++++++++++++++++++++ board/BuR/bur_kwb/am335xScreen.h | 45 ++++ board/BuR/bur_kwb/board.c | 522 ++++++++++++++++++++++++++++++++++++ board/BuR/bur_kwb/board.h | 18 ++ board/BuR/bur_kwb/mux.c | 213 +++++++++++++++ board/BuR/bur_kwb/u-boot.lds | 101 +++++++
See previous comments. Repeating the "bur_" part in the board directory name is redundant; I recommend to drop that.
Quoted 3 lines
+ * History
+ * =======
+ * 17.12.2013 hpm created
Please drop this. Please fix globally.
board/BuR/bur_kwb/am335xScreen.c line 43
Quoted 6 lines
board/BuR/bur_kwb/am335xScreen.c new file +6
-0+#define DEBUG +#ifdef DEBUG +#define DBG (...) printf(__VA_ARGS__) +#else +#define DBG (...) +#endif /* DEBUG */
We already have debug(); please use existing standard facilities.
Quoted 1 line
board/BuR/bur_kwb/am335xScreen.c new file +1
-0+if ('\r' == *str) {
...
board/BuR/bur_kwb/am335xScreen.c line 395
Quoted 1 line
board/BuR/bur_kwb/am335xScreen.c new file +1
-0+ }else if ('\n' == *str) {
Please avoid this reversed notation style. Please fix globally.
...
board/BuR/bur_kwb/am335xScreen.c line 462
Quoted 4 lines
board/BuR/bur_kwb/am335xScreen.c new file +4
-0+} +int drawrecticle (unsigned int x,unsigned int y, +unsigned int w,unsigned int h,unsigned int color) +{
CodingStyle says: "In source files, separate functions with one blank line." Please fix globally.
board/BuR/bur_kwb/am335xScreen.c line 467
Quoted 1 line
board/BuR/bur_kwb/am335xScreen.c new file +1
-0+setPix (&screen, j, i, color);
We do not allow CamelCase identifiers. Please fix globally.
Quoted 1 line
+int
prints(const char *fmt, ...)
...
Quoted 1 line
+int
printsxy(unsigned int x, unsigned int y, const char *fmt, ...)
etc.
BTW - are you not reinventing the wheel here? What about functions like video_drawstring(), video_putchar(), ... ?
board/BuR/bur_kwb/board.c
Quoted 4 lines
index 0000000..5a1b15f
board/BuR/bur_kwb/board.c new file +0
-0@@ -0,0 +1,522 @@
Pretty significant parts of this file appear to be identical to code in board/BuR/bur_tseries/board.c as added by your earlier patch. Please factor out such common code into a common/ directory so it can be shared across boards.
Quoted 5 lines
board/BuR/bur_kwb/board.c new file +5
-0+* History +* ======= +* xx.10.2013 hpm - created, adopted from ti_am335x_evm +* 06.12.2013 hpm - setting MPU_PLL to 600 MHz (as required for +* industrial)
board/BuR/bur_kwb/board.c line 29
Quoted 10 lines
board/BuR/bur_kwb/board.c new file +10
-0+* - implemented simple boot-mode detection +* - reduced resetpulse for USB2SD controller +* from 5ms to 1ms +* 10.12.2013 hpm - switch OFF LCD-Screen within SPL-Stage +* (due to invalid 3V3 pullup resistor) +* - powerUP 3V3 via I2C-Resetcontroller within SPL-Stage +* 16.12.2013 hpm - V1.10: changed bootaddr of VxWorks from +* 0x82000000 to 0x80100000 +* 24.12.2013 hpm - V1.11: added LCD-support +* 30.01.2014 hpm - V2.00: ported to new U-Boot (2014) sources
As mentioned before: please drop globally!
board/BuR/bur_kwb/board.c line 421
Quoted 10 lines
board/BuR/bur_kwb/board.c new file +10
-0+printf ("echo setting PMIC Register in the RTC.\n" ); + *(unsigned int *)0x44e3e098 =0x1f010 ; +printf ("read back PMIC Register: 0x%08x\n" , + *(unsigned int *)0x44e3e098 ); + + year = *(unsigned int *)0x44e3e014 ; + mon = *(unsigned int *)0x44e3e010 ; + d = *(unsigned int *)0x44e3e00C ; + h = *(unsigned int *)0x44e3e008 ; + min = *(unsigned int *)0x44e3e004 ;
Please use proper I/O accessors to access hardware registers, and declare a proper C struct to describe the register layout. Please fix globally.
Quoted 4 lines
board/BuR/bur_kwb/board.c new file +4
-0+static struct cpsw_slave_data cpsw_slaves[] = { + { + .slave_reg_ofs =0x208 , + .sliver_reg_ofs =0xd80 ,
...
board/BuR/bur_kwb/board.c line 455
Quoted 2 lines
board/BuR/bur_kwb/board.c new file +2
-0+ .slave_reg_ofs = 0x308, + .sliver_reg_ofs = 0xdc0,
Would it make sense to provide symboolic names for such magic numbers?
And how about some comments to explain the actual settings?
Quoted 13 lines
board/BuR/bur_kwb/board.h new file +7
-0@@ -0,0 +1,18 @@ +/* +* board.h +* +* BUR-KWB boards information header +* +* Copyright (C) 2013, Bernecker & Rainer Industrieelektronik GmbH - +* http://www.br-automation.com
board/BuR/bur_kwb/board.h line 17
Quoted 10 lines
board/BuR/bur_kwb/board.h new file +10
-0+* +* SPDX-License-Identifier: GPL-2.0+ +*/ + +#ifndef _BOARD_H_ +#define _BOARD_H_ + +void enable_uart0_pin_mux (void ); +void enable_i2c0_pin_mux (void ); +void enable_board_pin_mux (void );
This file appears to be identical to board/BuR/bur_tseries/board.h as added by your earlier patch. Please use a common header file instead.
Quoted 6 lines
board/BuR/bur_kwb/mux.c new file +0
-0
board/BuR/bur_kwb/mux.c line 110
Quoted 10 lines
board/BuR/bur_kwb/mux.c new file +9
-0@@ -0,0 +1,213 @@ +static struct module_pin_mux uart0_pin_mux[] = { +/* UART0_CTS */ + {OFFSET (uart0_ctsn), (MODE (7 ) |PULLUDEN |PULLUP_EN |RXACTIVE )}, +/* UART0_RXD */ + {OFFSET (uart0_rxd), (MODE (0 ) |PULLUDEN |PULLUP_EN |RXACTIVE )}, +/* UART0_TXD */ + {OFFSET (uart0_txd), (MODE (0 ) |PULLUDEN )}, + {-1 }, +};
Again, there is lots of duplicated code. Please factor out common parts. Please fix globally.
board/BuR/bur_kwb/u-boot.lds
Quoted 5 lines
board/BuR/bur_kwb/u-boot.lds new file +0
-0
Not needed? Drop??
include/configs/bur_kwb.h
Quoted 5 lines
include/configs/bur_kwb.h new file +0
-0
Large duplicated sections again...
Best regards,
Wolfgang Denk
Signature · 5 lines
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
If the facts don't fit the theory, change the facts.
-- Albert EinsteinPATCH v2 1/1 Add support for B&R KWB Motherboard
In reply to Hannes PetermaierAdds support for Bernecker & Rainer Industrieelektronik GmbH KWB Motherboard, using TI's AM3352 SoC.
Most of code is derived from TI's AM335x_EVM
---
---
Changes for v2:
- Coding Style cleanup
- using common/shared code sections of other B&R Motherboards
- common files are also included in tsereies board
arch/arm/include/asm/arch-am33xx/cpu.h | 6 +- board/BuR/common/bur_common.h | 22 +++ board/BuR/common/common.c | 216 ++++++++++++++++++++++++++++ board/BuR/kwb/Makefile | 12 ++ board/BuR/kwb/board.c | 240 ++++++++++++++++++++++++++++++++ board/BuR/kwb/mux.c | 195 ++++++++++++++++++++++++++ boards.cfg | 1 + include/configs/bur_am335x_common.h | 197 ++++++++++++++++++++++++++ include/configs/kwb.h | 128 +++++++++++++++++ 9 files changed, 1015 insertions(+), 2 deletions(-) create mode 100644 board/BuR/common/bur_common.h create mode 100644 board/BuR/common/common.c create mode 100644 board/BuR/kwb/Makefile create mode 100644 board/BuR/kwb/board.c create mode 100644 board/BuR/kwb/mux.c create mode 100644 include/configs/bur_am335x_common.h create mode 100644 include/configs/kwb.h
arch/arm/include/asm/arch-am33xx/cpu.h +4 -2
@@ -171,7 +171,8 @@ struct cm_wkuppll {unsigned int resv11[1 ];unsigned int wkup_uart0ctrl;/* offset 0xB4 */ unsigned int wkup_i2c0ctrl;/* offset 0xB8 */ -unsigned int resv12[7 ]; +unsigned int wkup_adctscctrl;/* offset 0xBC */ +unsigned int resv12[6 ];unsigned int divm6dpllcore;/* offset 0xD8 */ };
@@ -221,7 +222,8 @@ struct cm_perpll {unsigned int tpccclkctrl;/* offset 0xBC */ unsigned int dcan0clkctrl;/* offset 0xC0 */ unsigned int dcan1clkctrl;/* offset 0xC4 */ -unsigned int resv6[2 ]; +unsigned int resv6; +unsigned int epwmss1clkctrl;/* offset 0xCC */ unsigned int emiffwclkctrl;/* offset 0xD0 */ unsigned int epwmss0clkctrl;/* offset 0xD4 */ unsigned int epwmss2clkctrl;/* offset 0xD8 */
board/BuR/common/bur_common.h new file +22 -0
@@ -0,0 +1,22 @@ +/* +* bur_comon.h +* +* common board information header for B&R boards +* +* Copyright (C) 2013 Hannes Petermaier <[email protected]> +* Bernecker & Rainer Industrieelektronik GmbH - http://www.br-automation.com +* +* SPDX-License-Identifier: GPL-2.0+ +*/ + +#ifndef _BUR_COMMON_H_ +#define _BUR_COMMON_H_ + +void blink (u32 blinks,u32 intervall,u32 pin); +void pmicsetup (u32 mpupll); +void enable_uart0_pin_mux (void ); +void enable_i2c0_pin_mux (void ); +void enable_board_pin_mux (void ); +int board_eth_init (bd_t *bis); + +#endif
board/BuR/common/common.c new file +216 -0
216 lines not on this page · raw message
board/BuR/kwb/Makefile new file +12 -0
@@ -0,0 +1,12 @@ +# +# Makefile +# +# Copyright (C) 2014 Hannes Petermaier <[email protected]> - +# Bernecker & Rainer Industrielektronik GmbH - http://www.br-automation.com/ +# +# SPDX-License-Identifier: GPL-2.0+ +# + +obj-$(CONFIG_SPL_BUILD) += mux.o +obj-y += ../common/common.o +obj-y += board.o
board/BuR/kwb/board.c new file +240 -0
240 lines not on this page · raw message
board/BuR/kwb/mux.c new file +195 -0
195 lines not on this page · raw message
boards.cfg +1 -0
@@ -255,6 +255,7 @@ Active arm armv7 am33xx phytec pcm051 Active arm armv7 am33xx siemens dxr2 dxr2 - Roger Meier <[email protected]> Active arm armv7 am33xx siemens pxm2 pxm2 - Roger Meier <[email protected]> Active arm armv7 am33xx siemens rut rut - Roger Meier <[email protected]> +Active arm armv7 am33xx BuR kwb kwb kwb:SERIAL1,CONS_INDEX=1 Hannes Petermaier <[email protected]> Active arm armv7 am33xx ti am335x am335x_boneblack am335x_evm:SERIAL1,CONS_INDEX=1,EMMC_BOOT Tom Rini <[email protected]> Active arm armv7 am33xx ti am335x am335x_evm am335x_evm:SERIAL1,CONS_INDEX=1,NAND Tom Rini <[email protected]> Active arm armv7 am33xx ti am335x am335x_evm_nor am335x_evm:SERIAL1,CONS_INDEX=1,NAND,NOR Tom Rini <[email protected]>
include/configs/bur_am335x_common.h new file +197 -0
197 lines not on this page · raw message
include/configs/kwb.h new file +128 -0
128 lines not on this page · raw message
Signature · 1 line
1.7.9.5
PATCH v2 1/1 Add support for B&R KWB Motherboard
Quoted 7 lines · Hannes Petermaier
Adds support for Bernecker & Rainer Industrieelektronik GmbH KWB Motherboard, using TI's AM3352 SoC.
Most of code is derived from TI's
AM335x_EVMSigned-off-by Hannes Petermaier <[email protected]>Cc trini at ti.com
Applied to u-boot-ti/master, thanks!
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: not available Type: application/pgp-signature Size: 836 bytes Desc: Digital signature URL: <http://lists.denx.de/pipermail/u-boot/attachments/20140221/2a9a0b11/attachment.pgp>