mvebu support for kirkwood HP T5325
Subsystems (5)
Andrew Lunn
maintainercover mvebu support for kirkwood HP T5325
This patchset adds support to mvebu for the HP T5325 thin client. This is the first kirkwood device using device tree which supports audio. However the audio codec is missing a device tree binding, and simple-audio-card does not yet quite support all the properties needed for this hardware. So C code is used for the audio devices.
Andrew Lunn (4):
ARM: Kirkwood: Add audio node to kirkwood.dtsi
ARM: mvebu: Add i2c alias so setting bus number
ARM: mvebu: Add HP T5325 thin client
ARM: mvebu: Add HP T5325 devices to {multi|mvebu}_v5_defconfig
arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/kirkwood-t5325.dts | 209 +++++++++++++++++++++++++++++++++++ arch/arm/boot/dts/kirkwood.dtsi | 12 +- arch/arm/configs/multi_v5_defconfig | 9 ++ arch/arm/configs/mvebu_v5_defconfig | 9 ++ arch/arm/mach-mvebu/Kconfig | 7 ++ arch/arm/mach-mvebu/Makefile | 1 + arch/arm/mach-mvebu/board-t5325.c | 41 +++++++ arch/arm/mach-mvebu/board.h | 22 ++++ arch/arm/mach-mvebu/kirkwood.c | 11 +- 10 files changed, 320 insertions(+), 2 deletions(-) create mode 100644 arch/arm/boot/dts/kirkwood-t5325.dts create mode 100644 arch/arm/mach-mvebu/board-t5325.c create mode 100644 arch/arm/mach-mvebu/board.h
Signature · 1 line
1.8.5.3
Andrew Lunn
maintainerPATCH 1/4 ARM: Kirkwood: Add audio node to kirkwood.dtsi
The binding has existed for a while, so add the missing node so it can be used by devices.
--- arch/arm/boot/dts/kirkwood.dtsi | 9 +++++++++ 1 file changed, 9 insertions(+)
arch/arm/boot/dts/kirkwood.dtsi +9 -0
@@ -310,5 +310,14 @@ #phy-cells = <0>; status = "ok"; }; + + audio0: audio-controller at a0000 { + compatible = "marvell,kirkwood-audio"; + reg = <0xa0000 0x2210>; + interrupts = <24>; + clocks = <&gate_clk 9>; + clock-names = "internal"; + status = "disabled"; + }; }; };
Signature · 1 line
1.8.5.3
PATCH 1/4 ARM: Kirkwood: Add audio node to kirkwood.dtsi
Dear Andrew Lunn,
Quoted 14 lines · Andrew Lunn
The binding has existed for a while, so add the missing node so it can be used by devices.
Signed-off-by Andrew Lunn <[email protected]>--- arch/arm/boot/dts/kirkwood.dtsi | 9 +++++++++ 1 file changed, 9 insertions(+)arch/arm/boot/dts/kirkwood.dtsi +0
-0@@ -310,5 +310,14 @@ #phy-cells = <0>;
arch/arm/boot/dts/kirkwood.dtsi line 320
Quoted 10 lines
arch/arm/boot/dts/kirkwood.dtsi +8
-0status = "ok"; }; + + audio0: audio-controller at a0000 { + compatible = "marvell,kirkwood-audio"; + reg = <0xa0000 0x2210>; + interrupts = <24>; + clocks = <&gate_clk 9>; + clock-names = "internal"; + status = "disabled";
Bad indentation for all properties except the first one.
Thomas
Signature · 3 lines
Thomas Petazzoni, CTO, Free Electrons Embedded Linux, Kernel and Android engineering http://free-electrons.com
PATCH 1/4 ARM: Kirkwood: Add audio node to kirkwood.dtsi
In reply to Andrew LunnHello.
Quoted 15 lines · Andrew Lunn
The binding has existed for a while, so add the missing node so it can be used by devices.
Signed-off-by Andrew Lunn <[email protected]>--- arch/arm/boot/dts/kirkwood.dtsi | 9 +++++++++ 1 file changed, 9 insertions(+)arch/arm/boot/dts/kirkwood.dtsi +0
-0@@ -310,5 +310,14 @@ #phy-cells = <0>; status = "ok";
arch/arm/boot/dts/kirkwood.dtsi line 321
Quoted 10 lines
arch/arm/boot/dts/kirkwood.dtsi +9
-0}; + + audio0: audio-controller at a0000 { + compatible = "marvell,kirkwood-audio"; + reg = <0xa0000 0x2210>; + interrupts = <24>; + clocks = <&gate_clk 9>; + clock-names = "internal"; + status = "disabled"; + };
Could you uniformly indent the node with tabs (like at least the one
above it)?
WBR, Sergei
Andrew Lunn
maintainerPATCH 2/4 ARM: mvebu: Add i2c alias so setting bus number
In reply to Andrew LunnWhen using platform_driver instantiation, the i2c bus was given bus number 0. The kirkwood-t5325 audio driver has this bus number hard coded for the address of the codec. However by default device tree i2c busses are dynamically allocated a bus number, starting from 1. Thus the kirkwood-t5325 cannot find its audio codec. By adding an alias in the DT file we can control the bus number and set it to 0. The codec can then be found.
--- arch/arm/boot/dts/kirkwood.dtsi | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-)
arch/arm/boot/dts/kirkwood.dtsi +2 -1
@@ -24,6 +24,7 @@ aliases { gpio0 = &gpio0; gpio1 = &gpio1; + i2c0 = &i2c0; }; mbus {
@@ -111,7 +112,7 @@ clocks = <&gate_clk 7>; }; - i2c at 11000 { + i2c0: i2c at 11000 { compatible = "marvell,mv64xxx-i2c"; reg = <0x11000 0x20>; #address-cells = <1>;
Signature · 1 line
1.8.5.3
Andrew Lunn
maintainerPATCH 3/4 ARM: mvebu: Add HP T5325 thin client
In reply to Andrew LunnConvert the kirkwood t5325-setup.c to mostly device tree for mach-mvebu. Part of the audio setup needs to remain in C for the moment until suitable bindings are designed and implemented. So add board code, triggered by the compatibility string.
The first version of the dts file was created by Thomas Petazzoni.
--- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/kirkwood-t5325.dts | 209 +++++++++++++++++++++++++++++++++++ arch/arm/mach-mvebu/Kconfig | 7 ++ arch/arm/mach-mvebu/Makefile | 1 + arch/arm/mach-mvebu/board-t5325.c | 41 +++++++ arch/arm/mach-mvebu/board.h | 22 ++++ arch/arm/mach-mvebu/kirkwood.c | 11 +- 7 files changed, 291 insertions(+), 1 deletion(-) create mode 100644 arch/arm/boot/dts/kirkwood-t5325.dts create mode 100644 arch/arm/mach-mvebu/board-t5325.c create mode 100644 arch/arm/mach-mvebu/board.h
arch/arm/boot/dts/Makefile +1 -0
@@ -132,6 +132,7 @@ kirkwood := \ kirkwood-rs411.dtb \ kirkwood-sheevaplug.dtb \ kirkwood-sheevaplug-esata.dtb \ + kirkwood-t5325.dtb \ kirkwood-topkick.dtb \ kirkwood-ts219-6281.dtb \ kirkwood-ts219-6282.dtb \
arch/arm/boot/dts/kirkwood-t5325.dts new file +209 -0
209 lines not on this page · raw message
arch/arm/mach-mvebu/Kconfig +7 -0
@@ -92,6 +92,13 @@ config MACH_KIRKWOOD Say 'Y' here if you want your kernel to support boards based on the Marvell Kirkwood device tree. +config MACH_T5325 + bool "HP T5325 thin client" + depends on MACH_KIRKWOOD + help + Say 'Y' here if you want your kernel to support the + HP T5325 Thin client + endmenu endif
arch/arm/mach-mvebu/Makefile +1 -0
@@ -9,3 +9,4 @@ obj-$(CONFIG_ARCH_MVEBU) += coherency.o coherency_ll.o pmsu.o obj-$(CONFIG_SMP) += platsmp.o headsmp.o obj-$(CONFIG_HOTPLUG_CPU) += hotplug.o obj-$(CONFIG_MACH_KIRKWOOD) += kirkwood.o kirkwood-pm.o +obj-$(CONFIG_MACH_T5325) += board-t5325.o
arch/arm/mach-mvebu/board-t5325.c new file +41 -0
41 lines not on this page · raw message
arch/arm/mach-mvebu/board.h new file +22 -0
@@ -0,0 +1,22 @@ +/* +* Board functions for Marvell System On Chip +* +* Copyright (C) 2014 +* +* Andrew Lunn <[email protected]> +* +* This file is licensed under the terms of the GNU General Public +* License version 2. This program is licensed "as is" without any +* warranty of any kind, whether express or implied. +*/ + +#ifndef __ARCH_MVEBU_BOARD_H +#define __ARCH_MVEBU_BOARD_H + +#ifdef CONFIG_MACH_T5325 +void t5325_init (void ); +#else +static inline void t5325_init (void ) {}; +#endif + +#endif
arch/arm/mach-mvebu/kirkwood.c +10 -1
@@ -25,6 +25,7 @@#include "kirkwood.h" #include "kirkwood-pm.h" #include "common.h" +#include "board.h" static struct resource kirkwood_cpufreq_resources[] = { [0 ] = {
@@ -158,6 +159,11 @@ void kirkwood_disable_mbus_error_propagation(void)writel (readl (cpu_config) & ~CPU_CONFIG_ERROR_PROP , cpu_config); } +static struct of_dev_auxdata auxdata[]__initdata = { +OF_DEV_AUXDATA ("marvell,kirkwood-audio" ,0xf10a0000 , +"mvebu-audio" ,NULL ), + {/* sentinel */ } +};static void __init kirkwood_dt_init (void ) {
@@ -174,7 +180,10 @@ static void __init kirkwood_dt_init(void)kirkwood_pm_init ();kirkwood_dt_eth_fixup (); -of_platform_populate (NULL , of_default_bus_match_table,NULL ,NULL ); +if (of_machine_is_compatible ("hp,t5325" )) +t5325_init (); + +of_platform_populate (NULL , of_default_bus_match_table, auxdata,NULL ); }static const char *const kirkwood_dt_board_compat[] = {
Signature · 1 line
1.8.5.3
PATCH 3/4 ARM: mvebu: Add HP T5325 thin client
Quoted 11 lines · Andrew Lunn
Convert the kirkwood
t5325-setup.cto mostly device tree for mach-mvebu. Part of the audio setup needs to remain in C for the moment until suitable bindings are designed and implemented. So add board code, triggered by the compatibility string.The first version of the dts file was created by Thomas Petazzoni.
Signed-off-by Andrew Lunn <[email protected]>--- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/kirkwood-t5325.dts | 209 +++++++++++++++++++++++++++++++++++
Please split this in two. dts|mach-mvebu
thx,
Jason.
Quoted 378 lines
arch/arm/mach-mvebu/Kconfig | 7 ++ arch/arm/mach-mvebu/Makefile | 1 + arch/arm/mach-mvebu/board-t5325.c | 41 +++++++ arch/arm/mach-mvebu/board.h | 22 ++++ arch/arm/mach-mvebu/kirkwood.c | 11 +- 7 files changed, 291 insertions(+), 1 deletion(-) create mode 100644 arch/arm/boot/dts/kirkwood-t5325.dts create mode 100644 arch/arm/mach-mvebu/board-t5325.c create mode 100644 arch/arm/mach-mvebu/board.harch/arm/boot/dts/Makefile +1
-0@@ -132,6 +132,7 @@ kirkwood := \ kirkwood-rs411.dtb \ kirkwood-sheevaplug.dtb \ kirkwood-sheevaplug-esata.dtb \ + kirkwood-t5325.dtb \ kirkwood-topkick.dtb \ kirkwood-ts219-6281.dtb \ kirkwood-ts219-6282.dtb \arch/arm/boot/dts/kirkwood-t5325.dts new file +209
-0@@ -0,0 +1,209 @@ +/* + * Device Tree file for HP t5325 Thin Client" + * + * Copyright (C) 2014 + * + * Thomas Petazzoni <[email protected]> + * Andrew Lunn <[email protected]> + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. +*/ + +/dts-v1/; + +#include "kirkwood.dtsi" +#include "kirkwood-6281.dtsi" + +/ { + model = "HP t5325 Thin Client"; + compatible = "hp,t5325", "marvell,kirkwood-88f6281", "marvell,kirkwood"; + + memory { + device_type = "memory"; + reg = <0x00000000 0x20000000>; + }; + + chosen { + bootargs = "console=ttyS0,115200n8"; + }; + + mbus { + pcie-controller { + status = "okay"; + + pcie at 1,0 { + status = "okay"; + }; + }; + }; + + ocp at f1000000 { + pinctrl: pinctrl at 10000 { + pinctrl-0 = <&pmx_i2s &pmx_sysrst>; + pinctrl-names = "default"; + + pmx_button_power: pmx-button_power { + marvell,pins = "mpp45"; + marvell,function = "gpio"; + }; + + pmx_power_off: pmx-power-off { + marvell,pins = "mpp48"; + marvell,function = "gpio"; + }; + + pmx_led: pmx-led { + marvell,pins = "mpp21"; + marvell,function = "gpio"; + }; + + pmx_usb_sata_power_enable: pmx-usb-sata-power-enable { + marvell,pins = "mpp44"; + marvell,function = "gpio"; + }; + + /* + * Redefined from kirkwood-6281.dtsi, because + * we don't use SPI CS on MPP0, but on MPP7. + */ + pmx_spi: pmx-spi { + marvell,pins = "mpp1", "mpp2", "mpp3", "mpp7"; + marvell,function = "spi"; + }; + + pmx_sysrst: pmx-sysrst { + marvell,pins = "mpp6"; + marvell,function = "sysrst"; + }; + + pmx_i2s: pmx-i2s { + marvell,pins = "mpp39", "mpp40", "mpp41", "mpp42", + "mpp43"; + marvell,function = "audio"; + }; + }; + + spi at 10600 { + pinctrl-0 = <&pmx_spi>; + pinctrl-names = "default"; + status = "okay"; + + flash at 0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "st,m25p80"; + spi-max-frequency = <86000000>; + reg = <0>; + mode = <0>; + + partition at 0 { + reg = <0x0 0x80000>; + label = "u-boot"; + }; + + partition at 1 { + reg = <0x80000 0x40000>; + label = "SSD firmware"; + }; + + partition at 2 { + reg = <0xc0000 0x10000>; + label = "u-boot env"; + }; + + partition at 3 { + reg = <0xd0000 0x10000>; + label = "permanent u-boot env"; + }; + + partition at 4 { + reg = <0xd0000 0x10000>; + label = "permanent u-boot env"; + }; + }; + }; + + i2c at 11000 { + status = "okay"; + + alc5621: alc5621 at 1a { + compatible = "realtek,alc5621"; + reg = <0x1a>; + }; + }; + + serial at 12000 { + status = "okay"; + }; + + sata at 80000 { + status = "okay"; + nr-ports = <2>; + }; + + audio: audio-controller at a0000 { + status = "okay"; + }; + }; + + regulators { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; + pinctrl-0 = <&pmx_usb_sata_power_enable>; + pinctrl-names = "default"; + + usb_power: regulator at 1 { + compatible = "regulator-fixed"; + reg = <1>; + regulator-name = "USB-SATA Power"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + regulator-always-on; + regulator-boot-on; + gpio = <&gpio1 12 GPIO_ACTIVE_HIGH>; + }; + }; + + gpio_keys { + compatible = "gpio-keys"; + #address-cells = <1>; + #size-cells = <0>; + pinctrl-0 = <&pmx_button_power>; + pinctrl-names = "default"; + + button at 1 { + label = "Power Button"; + linux,code = < KEY_POWER >; + gpios = <&gpio1 13 GPIO_ACTIVE_HIGH>; + }; + }; + + gpio_poweroff { + compatible = "gpio-poweroff"; + pinctrl-0 = <&pmx_power_off>; + pinctrl-names = "default"; + gpios = <&gpio1 17 GPIO_ACTIVE_HIGH>; + }; + +}; + +&mdio { + status = "okay"; + + ethphy0: ethernet-phy { + device_type = "ethernet-phy"; + reg = <8>; + }; +}; + +ð0 { + status = "okay"; + ethernet0-port at 0 { + phy-handle = <ðphy0>; + }; +}; +arch/arm/mach-mvebu/Kconfig +7
-0@@ -92,6 +92,13 @@ config MACH_KIRKWOOD Say 'Y' here if you want your kernel to support boards based on the Marvell Kirkwood device tree. +config MACH_T5325 + bool "HP T5325 thin client" + depends on MACH_KIRKWOOD + help + Say 'Y' here if you want your kernel to support the + HP T5325 Thin client + endmenu endifarch/arm/mach-mvebu/Makefile +1
-0@@ -9,3 +9,4 @@ obj-$(CONFIG_ARCH_MVEBU) += coherency.o coherency_ll.o pmsu.o obj-$(CONFIG_SMP) += platsmp.o headsmp.o obj-$(CONFIG_HOTPLUG_CPU) += hotplug.o obj-$(CONFIG_MACH_KIRKWOOD) += kirkwood.o kirkwood-pm.o +obj-$(CONFIG_MACH_T5325) += board-t5325.oarch/arm/mach-mvebu/board-t5325.c new file +41
-0@@ -0,0 +1,41 @@ +/* +* HP T5325 Board Setup +* +* Copyright (C) 2014 +* +* Andrew Lunn <[email protected]> +* +* This file is licensed under the terms of the GNU General Public +* License version 2. This program is licensed "as is" without any +* warranty of any kind, whether express or implied. +*/ + +#include <linux/kernel.h> +#include <linux/i2c.h> +#include <linux/init.h> +#include <linux/platform_device.h> +#include <sound/alc5623.h> +#include "board.h" + +static struct platform_device hp_t5325_audio_device = { + .name ="t5325-audio" , + .id =-1 , +}; + +static struct alc5623_platform_data alc5621_data = { + .add_ctrl =0x3700 , + .jack_det_ctrl =0x4810 , +}; + +static struct i2c_board_info i2c_board_info[]__initdata = { + { +I2C_BOARD_INFO ("alc5621" ,0x1a ), + .platform_data = &alc5621_data, + }, +}; + +void __init t5325_init (void ) +{ +i2c_register_board_info (0 , i2c_board_info,ARRAY_SIZE (i2c_board_info)); +platform_device_register (&hp_t5325_audio_device); +}arch/arm/mach-mvebu/board.h new file +22
-0@@ -0,0 +1,22 @@ +/* +* Board functions for Marvell System On Chip +* +* Copyright (C) 2014 +* +* Andrew Lunn <[email protected]> +* +* This file is licensed under the terms of the GNU General Public +* License version 2. This program is licensed "as is" without any +* warranty of any kind, whether express or implied. +*/ + +#ifndef __ARCH_MVEBU_BOARD_H +#define __ARCH_MVEBU_BOARD_H + +#ifdef CONFIG_MACH_T5325 +void t5325_init (void ); +#else +static inline void t5325_init (void ) {}; +#endif + +#endif arch/arm/mach-mvebu/kirkwood.c +10
-1@@ -25,6 +25,7 @@#include "kirkwood.h" #include "kirkwood-pm.h" #include "common.h" +#include "board.h" static struct resource kirkwood_cpufreq_resources[] = { [0 ] = {@@ -158,6 +159,11 @@ void kirkwood_disable_mbus_error_propagation(void)writel (readl (cpu_config) & ~CPU_CONFIG_ERROR_PROP , cpu_config); } +static struct of_dev_auxdata auxdata[]__initdata = { +OF_DEV_AUXDATA ("marvell,kirkwood-audio" ,0xf10a0000 , +"mvebu-audio" ,NULL ), + {/* sentinel */ } +};static void __init kirkwood_dt_init (void ) {@@ -174,7 +180,10 @@ static void __init kirkwood_dt_init(void)kirkwood_pm_init ();kirkwood_dt_eth_fixup (); -of_platform_populate (NULL , of_default_bus_match_table,NULL ,NULL ); +if (of_machine_is_compatible ("hp,t5325" )) +t5325_init (); + +of_platform_populate (NULL , of_default_bus_match_table, auxdata,NULL ); }static const char *const kirkwood_dt_board_compat[] = {Signature · 1 line
1.8.5.3
PATCH 3/4 ARM: mvebu: Add HP T5325 thin client
In reply to Andrew LunnDear Andrew Lunn,
Sorry, I'm in a nitpick mood it seems :)
arch/arm/boot/dts/kirkwood-t5325.dts line 180
Quoted 3 lines · Andrew Lunn
arch/arm/boot/dts/kirkwood-t5325.dts new file +3
-0+ button at 1 { + label = "Power Button"; + linux,code = < KEY_POWER >;
Why spaces before and after KEY_POWER ?
arch/arm/mach-mvebu/Kconfig config MACH_KIRKWOOD · line 100
Quoted 6 lines
arch/arm/mach-mvebu/Kconfig +6
-0+config MACH_T5325 + bool "HP T5325 thin client" + depends on MACH_KIRKWOOD + help + Say 'Y' here if you want your kernel to support the + HP T5325 Thin client
Indentation for help text should be one tab and two spaces.
Thanks!
Thomas
Signature · 3 lines
Thomas Petazzoni, CTO, Free Electrons Embedded Linux, Kernel and Android engineering http://free-electrons.com
Andrew Lunn
maintainerPATCH 4/4 ARM: mvebu: Add HP T5325 devices to {multi|mvebu}_v5_defconfig
In reply to Andrew LunnThe HP T5325 has a PCI based VGA controller. Add the frame buffer driver, and frame buffer support to the defconfig's. Additionally add the soc audio framework and the necessary codec.
--- arch/arm/configs/multi_v5_defconfig | 9 +++++++++ arch/arm/configs/mvebu_v5_defconfig | 9 +++++++++ 2 files changed, 18 insertions(+)
arch/arm/configs/multi_v5_defconfig +9 -0
@@ -11,6 +11,7 @@ CONFIG_MODULE_UNLOAD=y # CONFIG_ARCH_MULTI_V7 is not set CONFIG_ARCH_MVEBU=y CONFIG_MACH_KIRKWOOD=y +CONFIG_MACH_T5325=y CONFIG_ARCH_MXC=y CONFIG_MACH_IMX25_DT=y CONFIG_MACH_IMX27_DT=y
@@ -101,6 +102,12 @@ CONFIG_THERMAL=y CONFIG_KIRKWOOD_THERMAL=y CONFIG_WATCHDOG=y CONFIG_ORION_WATCHDOG=y +CONFIG_FB=y +CONFIG_SOUND=y +CONFIG_SND=y +CONFIG_SND_SOC=y +CONFIG_SND_KIRKWOOD_SOC=y +CONFIG_SND_KIRKWOOD_SOC_T5325=y # CONFIG_ABX500_CORE is not set CONFIG_REGULATOR=y CONFIG_REGULATOR_FIXED_VOLTAGE=y
@@ -150,6 +157,8 @@ CONFIG_RTC_DRV_S35390A=y CONFIG_RTC_DRV_MV=y CONFIG_DMADEVICES=y CONFIG_MV_XOR=y +CONFIG_STAGING=y +CONFIG_FB_XGI=y CONFIG_EXT2_FS=y CONFIG_EXT3_FS=y # CONFIG_EXT3_FS_XATTR is not set
arch/arm/configs/mvebu_v5_defconfig +9 -0
@@ -11,6 +11,7 @@ CONFIG_MODULE_UNLOAD=y # CONFIG_ARCH_MULTI_V7 is not set CONFIG_ARCH_MVEBU=y CONFIG_MACH_KIRKWOOD=y +CONFIG_MACH_T5325=y # CONFIG_CPU_FEROCEON_OLD_ID is not set CONFIG_PCI_MVEBU=y CONFIG_PREEMPT=y
@@ -93,6 +94,12 @@ CONFIG_SENSORS_LM85=y CONFIG_THERMAL=y CONFIG_WATCHDOG=y CONFIG_ORION_WATCHDOG=y +CONFIG_FB=y +CONFIG_SOUND=y +CONFIG_SND=y +CONFIG_SND_SOC=y +CONFIG_SND_KIRKWOOD_SOC=y +CONFIG_SND_KIRKWOOD_SOC_T5325=y CONFIG_REGULATOR=y CONFIG_REGULATOR_FIXED_VOLTAGE=y CONFIG_HID_DRAGONRISE=y
@@ -137,6 +144,8 @@ CONFIG_RTC_DRV_S35390A=y CONFIG_RTC_DRV_MV=y CONFIG_DMADEVICES=y CONFIG_MV_XOR=y +CONFIG_STAGING=y +CONFIG_FB_XGI=y CONFIG_EXT2_FS=y CONFIG_EXT3_FS=y # CONFIG_EXT3_FS_XATTR is not set
Signature · 1 line
1.8.5.3
PATCH 4/4 ARM: mvebu: Add HP T5325 devices to {multi|mvebu}_v5_defconfig
Quoted 8 lines · Andrew Lunn
The HP T5325 has a PCI based VGA controller. Add the frame buffer driver, and frame buffer support to the defconfig's. Additionally add the soc audio framework and the necessary codec.
Signed-off-by Andrew Lunn <[email protected]>--- arch/arm/configs/multi_v5_defconfig | 9 +++++++++ arch/arm/configs/mvebu_v5_defconfig | 9 +++++++++
This should be fine for this window. In the future, though, we'll follow the pattern for multi_v5 as for multi_v7. Meaning those patches go straight to the arm-soc maintainers since that file tends to get riddled with conflicts.
thx,
Jason.