Skip to contentSkip to conversation

staging/iio/adc: change the MXS touchscreen driver implementation

PATCH Superseded Juergen Beisert 8 participants 44 messages Sep 23, 2013 – Feb 24, 2014

Subsystems (6)
lore
Share & tools
lore
#0 lore raw

PATCH v6 1/1 staging/iio/adc: change the MXS touchscreen driver implementation

The following series replaces the current busy loop touchscreen implementation for i.MX28/i.MX23 SoCs by a fully interrupt driven implementation.

Since i.MX23 and i.MX28 silicon differs, the existing implementation can be used for the i.MX28 SoC only.

The first patch adds proper clock handling. Various platforms seems to disable the internal 2 kHz clock which is used by the LRADC delay units.

The next two patches of this series move the i.MX28 specific definitions out of the way. The forth patch simplifies the register access to make it easier to add the i.MX23 support. Then the i.MX23 specific definitions are added, also the code to distinguish both SoCs at run-time.
Up to here the existing touchscreen driver will now run on an i.MX23 Soc as well.

When these i.MX SoCs are running from battery it seems not to be a good idea to run a busy loop to detect touches and their location. The 6th patch adds a fully interrupt driven implementation which makes use of the built-in delay and multiple sample features of the touchscreen controller. This will reduce the interrupt load to a minimum.

The remaining patches in this series just removes the existing busy loop implementation, add a proposal for devicetree binding and a reminder what has still to be done with the LRADC driver.

Changes since v5:

- add missing clock handling which prevents the delay units from work (this should make it work on the MX28EVK and M28EVK as well)

Changes since v4:

- honor Jonathan's comments about function names
- honor Dmitry's comments about workqueue canceling and interrupts
- adding devicetree bindings proposal

Changes since v3:

- split adding register access functions and i.MX23 support into two patches

Changes since v2:

- useless debug output removed

Changes since v1:

- adding register access functions to make the existing code more readable
- adding some functions to distinguish the SoCs at run-time to avoid if-else contructs whenever differences in the register layout between i.MX23 and i.MX28 must be handled

Comments are welcome.

Juergen

#1 lore raw

PATCH 1/9 Staging/iio/adc/touchscreen/MXS: add proper clock handling

The delay units inside the LRADC depend on the presence of a 2 kHz clock. This change enables the clock to be able to use the delay unit for the touchscreen part of the driver.

---
 arch/arm/boot/dts/imx23.dtsi        | 1 +
 arch/arm/boot/dts/imx28.dtsi        | 1 +
 drivers/staging/iio/adc/mxs-lradc.c | 7 +++++++
 3 files changed, 9 insertions(+)
arch/arm/boot/dts/imx23.dtsi +1 -0
index 28b5ce2..07caf76 100644
@@ -430,6 +430,7 @@
 				reg = <0x80050000 0x2000>;
 				interrupts = <36 37 38 39 40 41 42 43 44>;
 				status = "disabled";
+				clocks = <&clks 26>;
 			};
 
 			spdif at 80054000 {
arch/arm/boot/dts/imx28.dtsi +1 -0
index 7363fde..175deef 100644
@@ -902,6 +902,7 @@
 				interrupts = <10 14 15 16 17 18 19
 						20 21 22 23 24 25>;
 				status = "disabled";
+				clocks = <&clks 41>;
 			};
 
 			spdif: spdif at 80054000 {
drivers/staging/iio/adc/mxs-lradc.c +7 -0
index a08c173..00b61ac 100644
@@ -35,6 +35,7 @@
 #include <linux/completion.h>
 #include <linux/delay.h>
 #include <linux/input.h>
+#include <linux/clk.h>
 
 #include <linux/iio/iio.h>
 #include <linux/iio/buffer.h>
@@ -134,6 +135,8 @@ struct mxs_lradc {
 	void __iomem		*base;
 	int			irq[13];
 
+	struct clk		*clk;
+
 	uint32_t		*buffer;
 	struct iio_trigger	*trig;
 
@@ -928,6 +931,9 @@ static int mxs_lradc_probe(struct platform_device *pdev)
 	if (IS_ERR(lradc->base))
 		return PTR_ERR(lradc->base);
 
+	lradc->clk = devm_clk_get(&pdev->dev, NULL);
+	clk_prepare_enable(lradc->clk);
+
 	INIT_WORK(&lradc->ts_work, mxs_lradc_ts_work);
 
 	/* Check if touchscreen is enabled in DT. */
@@ -1020,6 +1026,7 @@ static int mxs_lradc_remove(struct platform_device *pdev)
 	iio_triggered_buffer_cleanup(iio);
 	mxs_lradc_trigger_remove(iio);
 
+	clk_disable_unprepare(lradc->clk);
 	return 0;
 }
 
Signature · 1 line
1.8.4.rc3
#2 lore raw

PATCH 1/9 Staging/iio/adc/touchscreen/MXS: add proper clock handling

drivers/staging/iio/adc/mxs-lradc.c static int mxs_lradc_probe(struct platform_device *pdev) · line 935

Quoted 2 lines · Juergen Beisert
drivers/staging/iio/adc/mxs-lradc.c +2 -0
+	lradc->clk = devm_clk_get(&pdev->dev, NULL);
+	clk_prepare_enable(lradc->clk);

clk_prepare_enable() may fail, so better check its return value.

#3 lore raw

PATCH 1/9 Staging/iio/adc/touchscreen/MXS: add proper clock handling

Hi Fabio,

Quoted 5 lines · On Monday 23 September 2013 17:13:03 Fabio Estevam wrote:

Review

Quoted 2 lines · Juergen Beisert
(quoted diff) +2 -0
+	lradc->clk = devm_clk_get(&pdev->dev, NULL);
+	clk_prepare_enable(lradc->clk);

clk_prepare_enable() may fail, so better check its return value.

Thanks for the comment. Better this way?

commit 825c5bb787a0dc9d25d480178e117be08810639c

Author: Juergen Beisert <[email protected]>
Date:   Mon Sep 23 16:10:56 2013 +0200

Staging/iio/adc/touchscreen/MXS: add proper clock handling

The delay units inside the LRADC depend on the presence of a 2 kHz clock. This change enables the clock to be able to use the delay unit for the touchscreen part of the driver.

arch/arm/boot/dts/imx23.dtsi +1 -0
index 28b5ce2..07caf76 100644
@@ -430,6 +430,7 @@
 				reg = <0x80050000 0x2000>;
 				interrupts = <36 37 38 39 40 41 42 43 44>;
 				status = "disabled";
+				clocks = <&clks 26>;
 			};
 
 			spdif@80054000 {
arch/arm/boot/dts/imx28.dtsi +1 -0
index 7363fde..175deef 100644
@@ -902,6 +902,7 @@
 				interrupts = <10 14 15 16 17 18 19
 						20 21 22 23 24 25>;
 				status = "disabled";
+				clocks = <&clks 41>;
 			};
 
 			spdif: spdif@80054000 {
drivers/staging/iio/adc/mxs-lradc.c +15 -0
index a08c173..eaca1ae 100644
@@ -35,6 +35,7 @@
 #include <linux/completion.h>
 #include <linux/delay.h>
 #include <linux/input.h>
+#include <linux/clk.h>
 
 #include <linux/iio/iio.h>
 #include <linux/iio/buffer.h>
@@ -134,6 +135,8 @@ struct mxs_lradc {
 	void __iomem		*base;
 	int			irq[13];
 
+	struct clk		*clk;
+
 	uint32_t		*buffer;
 	struct iio_trigger	*trig;
 
@@ -928,6 +931,17 @@ static int mxs_lradc_probe(struct platform_device *pdev)
 	if (IS_ERR(lradc->base))
 		return PTR_ERR(lradc->base);
 
+	lradc->clk = devm_clk_get(&pdev->dev, NULL);
+	if (IS_ERR(lradc->clk)) {
+		dev_err(dev, "Failed to get the delay unit clock\n");
+		return PTR_ERR(lradc->clk);
+	}
+	ret = clk_prepare_enable(lradc->clk);
+	if (ret != 0) {
+		dev_err(dev, "Failed to enable the delay unit clock\n");
+		return ret;
+	}
+
 	INIT_WORK(&lradc->ts_work, mxs_lradc_ts_work);
 
 	/* Check if touchscreen is enabled in DT. */
@@ -1020,6 +1034,7 @@ static int mxs_lradc_remove(struct platform_device *pdev)
 	iio_triggered_buffer_cleanup(iio);
 	mxs_lradc_trigger_remove(iio);
 
+	clk_disable_unprepare(lradc->clk);
 	return 0;
 }
 

Juergen

Signature · 2 lines
Pengutronix e.K.                              | Juergen Beisert             |
Linux Solutions for Science and Industry      | http://www.pengutronix.de/  |
reviewer
#4 lore raw

PATCH 1/9 Staging/iio/adc/touchscreen/MXS: add proper clock handling

Quoted 10 lines · J?rgen Beisert

Hi Fabio,

Quoted 5 lines · On Monday 23 September 2013 17:13:03 Fabio Estevam wrote:

Review

Quoted 2 lines · Juergen Beisert
(quoted diff) +2 -0
+   lradc->clk = devm_clk_get(&pdev->dev, NULL);
+   clk_prepare_enable(lradc->clk);

clk_prepare_enable() may fail, so better check its return value.

Thanks for the comment. Better this way?

Yes, looks better.

Thanks,

Fabio Estevam

maintainer Applied
#5 lore raw

PATCH 1/9 Staging/iio/adc/touchscreen/MXS: add proper clock handling

In reply to Jürgen Beisert
Quoted 9 lines · Jürgen Beisert

Hi Fabio,

Quoted 5 lines · On Monday 23 September 2013 17:13:03 Fabio Estevam wrote:

Review

Quoted 2 lines · Juergen Beisert
(quoted diff) +2 -0
+	lradc->clk = devm_clk_get(&pdev->dev, NULL);
+	clk_prepare_enable(lradc->clk);

clk_prepare_enable() may fail, so better check its return value.

Quoted 5 lines

Thanks for the comment. Better this way?

commit 825c5bb787a0dc9d25d480178e117be08810639c

Author: Juergen Beisert <[email protected]>
Date:   Mon Sep 23 16:10:56 2013 +0200

Applied. If you are going to have a new patch version in the middle of the thread please generate it with git format-patch and then send it as a reply to the email you are responding to. Applying a patch like this is no where near as easy.

Applied to the togreg branch of iio.git

Thanks

Quoted 82 lines

Staging/iio/adc/touchscreen/MXS: add proper clock handling

The delay units inside the LRADC depend on the presence of a 2 kHz clock. This change enables the clock to be able to use the delay unit for the touchscreen part of the driver.

arch/arm/boot/dts/imx23.dtsi +1 -0
index 28b5ce2..07caf76 100644
@@ -430,6 +430,7 @@
 				reg = <0x80050000 0x2000>;
 				interrupts = <36 37 38 39 40 41 42 43 44>;
 				status = "disabled";
+				clocks = <&clks 26>;
 			};
 
 			spdif@80054000 {
arch/arm/boot/dts/imx28.dtsi +1 -0
index 7363fde..175deef 100644
@@ -902,6 +902,7 @@
 				interrupts = <10 14 15 16 17 18 19
 						20 21 22 23 24 25>;
 				status = "disabled";
+				clocks = <&clks 41>;
 			};
 
 			spdif: spdif@80054000 {
drivers/staging/iio/adc/mxs-lradc.c +15 -0
index a08c173..eaca1ae 100644
@@ -35,6 +35,7 @@
 #include <linux/completion.h>
 #include <linux/delay.h>
 #include <linux/input.h>
+#include <linux/clk.h>
 
 #include <linux/iio/iio.h>
 #include <linux/iio/buffer.h>
@@ -134,6 +135,8 @@ struct mxs_lradc {
 	void __iomem		*base;
 	int			irq[13];
 
+	struct clk		*clk;
+
 	uint32_t		*buffer;
 	struct iio_trigger	*trig;
 
@@ -928,6 +931,17 @@ static int mxs_lradc_probe(struct platform_device *pdev)
 	if (IS_ERR(lradc->base))
 		return PTR_ERR(lradc->base);
 
+	lradc->clk = devm_clk_get(&pdev->dev, NULL);
+	if (IS_ERR(lradc->clk)) {
+		dev_err(dev, "Failed to get the delay unit clock\n");
+		return PTR_ERR(lradc->clk);
+	}
+	ret = clk_prepare_enable(lradc->clk);
+	if (ret != 0) {
+		dev_err(dev, "Failed to enable the delay unit clock\n");
+		return ret;
+	}
+
 	INIT_WORK(&lradc->ts_work, mxs_lradc_ts_work);
 
 	/* Check if touchscreen is enabled in DT. */
@@ -1020,6 +1034,7 @@ static int mxs_lradc_remove(struct platform_device *pdev)
 	iio_triggered_buffer_cleanup(iio);
 	mxs_lradc_trigger_remove(iio);
 
+	clk_disable_unprepare(lradc->clk);
 	return 0;
 }
 

Juergen

#6 lore raw

PATCH 1/9 Staging/iio/adc/touchscreen/MXS: add proper clock handling

In reply to Juergen Beisert

Hi,

Quoted 22 lines · Juergen Beisert
drivers/staging/iio/adc/mxs-lradc.c +3 -0
index a08c173..00b61ac 100644
@@ -35,6 +35,7 @@
 #include <linux/completion.h>
 #include <linux/delay.h>
 #include <linux/input.h>
+#include <linux/clk.h>
 
 #include <linux/iio/iio.h>
 #include <linux/iio/buffer.h>
@@ -134,6 +135,8 @@ struct mxs_lradc {
 	void __iomem		*base;
 	int			irq[13];
 
+	struct clk		*clk;
+
 	uint32_t		*buffer;
 	struct iio_trigger	*trig;
 

drivers/staging/iio/adc/mxs-lradc.c static int mxs_lradc_probe(struct platform_device *pdev) · line 936

Quoted 6 lines
drivers/staging/iio/adc/mxs-lradc.c +3 -0
@@ -928,6 +931,9 @@ static int mxs_lradc_probe(struct platform_device *pdev)
 	if (IS_ERR(lradc->base))
 		return PTR_ERR(lradc->base);
 
+	lradc->clk = devm_clk_get(&pdev->dev, NULL);
+	clk_prepare_enable(lradc->clk);
+

Wouldn't it make sense to enable the clock only when the device is opened to save power while not actually in use?

Lothar Wa?mann

Signature · 9 lines
___________________________________________________________

Ka-Ro electronics GmbH | Pascalstra?e 22 | D - 52076 Aachen
Phone: +49 2408 1402-0 | Fax: +49 2408 1402-10
Gesch?ftsf?hrer: Matthias Kaussen
Handelsregistereintrag: Amtsgericht Aachen, HRB 4996

www.karo-electronics.de | info at karo-electronics.de
___________________________________________________________
#7 lore raw

PATCH 1/9 Staging/iio/adc/touchscreen/MXS: add proper clock handling

Hi Lothar,

Quoted 11 lines · On Monday 23 September 2013 17:30:18 Lothar Waßmann wrote:

drivers/staging/iio/adc/mxs-lradc.c static int mxs_lradc_probe(struct platform_device · line 936

Quoted 8 lines

[...]

drivers/staging/iio/adc/mxs-lradc.c +3 -0
@@ -928,6 +931,9 @@ static int mxs_lradc_probe(struct platform_device
 *pdev) if (IS_ERR(lradc->base))
 		return PTR_ERR(lradc->base);
 
+	lradc->clk = devm_clk_get(&pdev->dev, NULL);
+	clk_prepare_enable(lradc->clk);
+

Wouldn't it make sense to enable the clock only when the device is opened to save power while not actually in use?

Sure. But I haven't analyzed yet if the IIO part of the driver also uses the delay units and - more important - when it use them.

@Marek: can you tell us, where the clock should be enabled in your part of the driver (if required)?

BTW: do we also need to get and enable the 24 MHz clock (used by the ADC itself)? I'm not sure if this clock is the "CLK_ANA24M" shown in their "Logical Diagram of Clock Domains". The datasheets also mention the "clk_xtal24m" clock for "analog 24 MHz clock domains". But does "Fixed clock domains" mean they are not switchable and thus always enabled?

Regards,
Juergen

Signature · 2 lines
Pengutronix e.K.                              | Juergen Beisert             |
Linux Solutions for Science and Industry      | http://www.pengutronix.de/  |
#8 lore raw

PATCH 2/9 Staging/iio/adc/touchscreen/MXS: distinguish i.MX23's and i.MX28's LRADC

In reply to Juergen Beisert

The LRADC units in i.MX23 and i.MX28 differ and we need to distinguish both SoC variants in order to make the touchscreen work on i.MX23

CC linux-arm-kernel at lists.infradead.org
CC linux-input at vger.kernel.org
CC devel at driverdev.osuosl.org
CC Marek Vasut <[email protected]>
CC Fabio Estevam <[email protected]>
CC Jonathan Cameron <[email protected]>
---
 drivers/staging/iio/adc/mxs-lradc.c | 3 +++
 1 file changed, 3 insertions(+)
drivers/staging/iio/adc/mxs-lradc.c +3 -0
index 00b61ac..3abc91f 100644
@@ -177,6 +177,8 @@ struct mxs_lradc {
 
 	struct input_dev	*ts_input;
 	struct work_struct	ts_work;
+
+	enum mxs_lradc_id	soc;
 };
 
 #define	LRADC_CTRL0				0x00
@@ -923,6 +925,7 @@ static int mxs_lradc_probe(struct platform_device *pdev)
 	}
 
 	lradc = iio_priv(iio);
+	lradc->soc = (enum mxs_lradc_id)of_id->data;
 
 	/* Grab the memory area */
 	iores = platform_get_resource(pdev, IORESOURCE_MEM, 0);
Signature · 1 line
1.8.4.rc3
maintainer Applied
#9 lore raw

PATCH 2/9 Staging/iio/adc/touchscreen/MXS: distinguish i.MX23's and i.MX28's LRADC

Quoted 10 lines · Juergen Beisert

The LRADC units in i.MX23 and i.MX28 differ and we need to distinguish both SoC variants in order to make the touchscreen work on i.MX23

Applied to the togreg branch of iio.git

Thanks

Quoted 26 lines
---
 drivers/staging/iio/adc/mxs-lradc.c | 3 +++
 1 file changed, 3 insertions(+)
drivers/staging/iio/adc/mxs-lradc.c +3 -0
index 00b61ac..3abc91f 100644
@@ -177,6 +177,8 @@ struct mxs_lradc {
 
 	struct input_dev	*ts_input;
 	struct work_struct	ts_work;
+
+	enum mxs_lradc_id	soc;
 };
 
 #define	LRADC_CTRL0				0x00
@@ -923,6 +925,7 @@ static int mxs_lradc_probe(struct platform_device *pdev)
 	}
 
 	lradc = iio_priv(iio);
+	lradc->soc = (enum mxs_lradc_id)of_id->data;
 
 	/* Grab the memory area */
 	iores = platform_get_resource(pdev, IORESOURCE_MEM, 0);
#10 lore raw

PATCH 3/9 Staging/iio/adc/touchscreen/MXS: separate i.MX28 specific register bits

In reply to Juergen Beisert

In order to support i.MX23 and i.MX28 within one driver we need to separate the register definitions which differ in both SoC variants.

CC linux-arm-kernel at lists.infradead.org
CC linux-input at vger.kernel.org
CC devel at driverdev.osuosl.org
CC Marek Vasut <[email protected]>
CC Fabio Estevam <[email protected]>
CC Jonathan Cameron <[email protected]>
---
 drivers/staging/iio/adc/mxs-lradc.c | 61 ++++++++++++++++++++-----------------
 1 file changed, 33 insertions(+), 28 deletions(-)
drivers/staging/iio/adc/mxs-lradc.c +33 -28
index 3abc91f..f2fb10a 100644
@@ -182,24 +182,29 @@ struct mxs_lradc {
 };
 
 #define	LRADC_CTRL0				0x00
-#define	LRADC_CTRL0_TOUCH_DETECT_ENABLE		(1 << 23)
-#define	LRADC_CTRL0_TOUCH_SCREEN_TYPE		(1 << 22)
-#define	LRADC_CTRL0_YNNSW	/* YM */	(1 << 21)
-#define	LRADC_CTRL0_YPNSW	/* YP */	(1 << 20)
-#define	LRADC_CTRL0_YPPSW	/* YP */	(1 << 19)
-#define	LRADC_CTRL0_XNNSW	/* XM */	(1 << 18)
-#define	LRADC_CTRL0_XNPSW	/* XM */	(1 << 17)
-#define	LRADC_CTRL0_XPPSW	/* XP */	(1 << 16)
-#define	LRADC_CTRL0_PLATE_MASK			(0x3f << 16)
+# define LRADC_CTRL0_MX28_TOUCH_DETECT_ENABLE	(1 << 23)
+# define LRADC_CTRL0_MX28_TOUCH_SCREEN_TYPE	(1 << 22)
+# define LRADC_CTRL0_MX28_YNNSW	/* YM */	(1 << 21)
+# define LRADC_CTRL0_MX28_YPNSW	/* YP */	(1 << 20)
+# define LRADC_CTRL0_MX28_YPPSW	/* YP */	(1 << 19)
+# define LRADC_CTRL0_MX28_XNNSW	/* XM */	(1 << 18)
+# define LRADC_CTRL0_MX28_XNPSW	/* XM */	(1 << 17)
+# define LRADC_CTRL0_MX28_XPPSW	/* XP */	(1 << 16)
+
+# define LRADC_CTRL0_MX28_PLATE_MASK \
+		(LRADC_CTRL0_MX28_TOUCH_DETECT_ENABLE | \
+		LRADC_CTRL0_MX28_YNNSW | LRADC_CTRL0_MX28_YPNSW | \
+		LRADC_CTRL0_MX28_YPPSW | LRADC_CTRL0_MX28_XNNSW | \
+		LRADC_CTRL0_MX28_XNPSW | LRADC_CTRL0_MX28_XPPSW)
 
 #define	LRADC_CTRL1				0x10
 #define	LRADC_CTRL1_TOUCH_DETECT_IRQ_EN		(1 << 24)
 #define	LRADC_CTRL1_LRADC_IRQ_EN(n)		(1 << ((n) + 16))
-#define	LRADC_CTRL1_LRADC_IRQ_EN_MASK		(0x1fff << 16)
+#define	LRADC_CTRL1_MX28_LRADC_IRQ_EN_MASK	(0x1fff << 16)
 #define	LRADC_CTRL1_LRADC_IRQ_EN_OFFSET		16
 #define	LRADC_CTRL1_TOUCH_DETECT_IRQ		(1 << 8)
 #define	LRADC_CTRL1_LRADC_IRQ(n)		(1 << (n))
-#define	LRADC_CTRL1_LRADC_IRQ_MASK		0x1fff
+#define	LRADC_CTRL1_MX28_LRADC_IRQ_MASK		0x1fff
 #define	LRADC_CTRL1_LRADC_IRQ_OFFSET		0
 
 #define	LRADC_CTRL2				0x20
@@ -267,7 +272,7 @@ static int mxs_lradc_read_raw(struct iio_dev *iio_dev,
 	 * Virtual channel 0 is always used here as the others are always not
 	 * used if doing raw sampling.
 	 */
-	writel(LRADC_CTRL1_LRADC_IRQ_EN_MASK,
+	writel(LRADC_CTRL1_MX28_LRADC_IRQ_EN_MASK,
 		lradc->base + LRADC_CTRL1 + STMP_OFFSET_REG_CLR);
 	writel(0xff, lradc->base + LRADC_CTRL0 + STMP_OFFSET_REG_CLR);
 
@@ -322,9 +327,9 @@ static int mxs_lradc_ts_touched(struct mxs_lradc *lradc)
 	uint32_t reg;
 
 	/* Enable touch detection. */
-	writel(LRADC_CTRL0_PLATE_MASK,
+	writel(LRADC_CTRL0_MX28_PLATE_MASK,
 		lradc->base + LRADC_CTRL0 + STMP_OFFSET_REG_CLR);
-	writel(LRADC_CTRL0_TOUCH_DETECT_ENABLE,
+	writel(LRADC_CTRL0_MX28_TOUCH_DETECT_ENABLE,
 		lradc->base + LRADC_CTRL0 + STMP_OFFSET_REG_SET);
 
 	msleep(LRADC_TS_SAMPLE_DELAY_MS);
@@ -370,21 +375,21 @@ static int32_t mxs_lradc_ts_sample(struct mxs_lradc *lradc,
 	 */
 	switch (plate) {
 	case LRADC_SAMPLE_X:
-		ctrl0 = LRADC_CTRL0_XPPSW | LRADC_CTRL0_XNNSW;
+		ctrl0 = LRADC_CTRL0_MX28_XPPSW | LRADC_CTRL0_MX28_XNNSW;
 		chan = 3;
 		break;
 	case LRADC_SAMPLE_Y:
-		ctrl0 = LRADC_CTRL0_YPPSW | LRADC_CTRL0_YNNSW;
+		ctrl0 = LRADC_CTRL0_MX28_YPPSW | LRADC_CTRL0_MX28_YNNSW;
 		chan = 4;
 		break;
 	case LRADC_SAMPLE_PRESSURE:
-		ctrl0 = LRADC_CTRL0_YPPSW | LRADC_CTRL0_XNNSW;
+		ctrl0 = LRADC_CTRL0_MX28_YPPSW | LRADC_CTRL0_MX28_XNNSW;
 		chan = 5;
 		break;
 	}
 
 	if (change) {
-		writel(LRADC_CTRL0_PLATE_MASK,
+		writel(LRADC_CTRL0_MX28_PLATE_MASK,
 			lradc->base + LRADC_CTRL0 + STMP_OFFSET_REG_CLR);
 		writel(ctrl0, lradc->base + LRADC_CTRL0 + STMP_OFFSET_REG_SET);
 
@@ -445,7 +450,7 @@ static void mxs_lradc_ts_work(struct work_struct *ts_work)
 
 	while (mxs_lradc_ts_touched(lradc)) {
 		/* Disable touch detector so we can sample the touchscreen. */
-		writel(LRADC_CTRL0_TOUCH_DETECT_ENABLE,
+		writel(LRADC_CTRL0_MX28_TOUCH_DETECT_ENABLE,
 			lradc->base + LRADC_CTRL0 + STMP_OFFSET_REG_CLR);
 
 		if (likely(valid)) {
@@ -494,7 +499,7 @@ static int mxs_lradc_ts_open(struct input_dev *dev)
 	lradc->stop_touchscreen = false;
 
 	/* Enable the touch-detect circuitry. */
-	writel(LRADC_CTRL0_TOUCH_DETECT_ENABLE,
+	writel(LRADC_CTRL0_MX28_TOUCH_DETECT_ENABLE,
 		lradc->base + LRADC_CTRL0 + STMP_OFFSET_REG_SET);
 
 	/* Enable the touch-detect IRQ. */
@@ -520,7 +525,7 @@ static void mxs_lradc_ts_close(struct input_dev *dev)
 		lradc->base + LRADC_CTRL1 + STMP_OFFSET_REG_CLR);
 
 	/* Power-down touchscreen touch-detect circuitry. */
-	writel(LRADC_CTRL0_TOUCH_DETECT_ENABLE,
+	writel(LRADC_CTRL0_MX28_TOUCH_DETECT_ENABLE,
 		lradc->base + LRADC_CTRL0 + STMP_OFFSET_REG_CLR);
 }
 
@@ -584,7 +589,7 @@ static irqreturn_t mxs_lradc_handle_irq(int irq, void *data)
 		LRADC_CTRL1_TOUCH_DETECT_IRQ_EN |
 		LRADC_CTRL1_TOUCH_DETECT_IRQ;
 
-	if (!(reg & LRADC_CTRL1_LRADC_IRQ_MASK))
+	if (!(reg & LRADC_CTRL1_MX28_LRADC_IRQ_MASK))
 		return IRQ_NONE;
 
 	/*
@@ -604,7 +609,7 @@ static irqreturn_t mxs_lradc_handle_irq(int irq, void *data)
 	else if (reg & LRADC_CTRL1_LRADC_IRQ(0))
 		complete(&lradc->completion);
 
-	writel(reg & LRADC_CTRL1_LRADC_IRQ_MASK,
+	writel(reg & LRADC_CTRL1_MX28_LRADC_IRQ_MASK,
 		lradc->base + LRADC_CTRL1 + STMP_OFFSET_REG_CLR);
 
 	return IRQ_HANDLED;
@@ -725,7 +730,7 @@ static int mxs_lradc_buffer_preenable(struct iio_dev *iio)
 	if (ret < 0)
 		goto err_buf;
 
-	writel(LRADC_CTRL1_LRADC_IRQ_EN_MASK,
+	writel(LRADC_CTRL1_MX28_LRADC_IRQ_EN_MASK,
 		lradc->base + LRADC_CTRL1 + STMP_OFFSET_REG_CLR);
 	writel(0xff, lradc->base + LRADC_CTRL0 + STMP_OFFSET_REG_CLR);
 
@@ -766,7 +771,7 @@ static int mxs_lradc_buffer_postdisable(struct iio_dev *iio)
 		lradc->base + LRADC_DELAY(0) + STMP_OFFSET_REG_CLR);
 
 	writel(0xff, lradc->base + LRADC_CTRL0 + STMP_OFFSET_REG_CLR);
-	writel(LRADC_CTRL1_LRADC_IRQ_EN_MASK,
+	writel(LRADC_CTRL1_MX28_LRADC_IRQ_EN_MASK,
 		lradc->base + LRADC_CTRL1 + STMP_OFFSET_REG_CLR);
 
 	kfree(lradc->buffer);
@@ -870,11 +875,11 @@ static int mxs_lradc_hw_init(struct mxs_lradc *lradc)
 	writel(0, lradc->base + LRADC_DELAY(3));
 
 	/* Configure the touchscreen type */
-	writel(LRADC_CTRL0_TOUCH_SCREEN_TYPE,
+	writel(LRADC_CTRL0_MX28_TOUCH_SCREEN_TYPE,
 		lradc->base + LRADC_CTRL0 + STMP_OFFSET_REG_CLR);
 
 	if (lradc->use_touchscreen == MXS_LRADC_TOUCHSCREEN_5WIRE) {
-		writel(LRADC_CTRL0_TOUCH_SCREEN_TYPE,
+		writel(LRADC_CTRL0_MX28_TOUCH_SCREEN_TYPE,
 			lradc->base + LRADC_CTRL0 + STMP_OFFSET_REG_SET);
 	}
 
@@ -888,7 +893,7 @@ static void mxs_lradc_hw_stop(struct mxs_lradc *lradc)
 {
 	int i;
 
-	writel(LRADC_CTRL1_LRADC_IRQ_EN_MASK,
+	writel(LRADC_CTRL1_MX28_LRADC_IRQ_EN_MASK,
 		lradc->base + LRADC_CTRL1 + STMP_OFFSET_REG_CLR);
 
 	for (i = 0; i < LRADC_MAX_DELAY_CHANS; i++)
Signature · 1 line
1.8.4.rc3
maintainer Applied
#11 lore raw

PATCH 3/9 Staging/iio/adc/touchscreen/MXS: separate i.MX28 specific register bits

Quoted 10 lines · Juergen Beisert

In order to support i.MX23 and i.MX28 within one driver we need to separate the register definitions which differ in both SoC variants.

Applied to the togreg branch of iio.git

Thanks

Quoted 183 lines
---
 drivers/staging/iio/adc/mxs-lradc.c | 61 ++++++++++++++++++++-----------------
 1 file changed, 33 insertions(+), 28 deletions(-)
drivers/staging/iio/adc/mxs-lradc.c +33 -28
index 3abc91f..f2fb10a 100644
@@ -182,24 +182,29 @@ struct mxs_lradc {
 };
 
 #define	LRADC_CTRL0				0x00
-#define	LRADC_CTRL0_TOUCH_DETECT_ENABLE		(1 << 23)
-#define	LRADC_CTRL0_TOUCH_SCREEN_TYPE		(1 << 22)
-#define	LRADC_CTRL0_YNNSW	/* YM */	(1 << 21)
-#define	LRADC_CTRL0_YPNSW	/* YP */	(1 << 20)
-#define	LRADC_CTRL0_YPPSW	/* YP */	(1 << 19)
-#define	LRADC_CTRL0_XNNSW	/* XM */	(1 << 18)
-#define	LRADC_CTRL0_XNPSW	/* XM */	(1 << 17)
-#define	LRADC_CTRL0_XPPSW	/* XP */	(1 << 16)
-#define	LRADC_CTRL0_PLATE_MASK			(0x3f << 16)
+# define LRADC_CTRL0_MX28_TOUCH_DETECT_ENABLE	(1 << 23)
+# define LRADC_CTRL0_MX28_TOUCH_SCREEN_TYPE	(1 << 22)
+# define LRADC_CTRL0_MX28_YNNSW	/* YM */	(1 << 21)
+# define LRADC_CTRL0_MX28_YPNSW	/* YP */	(1 << 20)
+# define LRADC_CTRL0_MX28_YPPSW	/* YP */	(1 << 19)
+# define LRADC_CTRL0_MX28_XNNSW	/* XM */	(1 << 18)
+# define LRADC_CTRL0_MX28_XNPSW	/* XM */	(1 << 17)
+# define LRADC_CTRL0_MX28_XPPSW	/* XP */	(1 << 16)
+
+# define LRADC_CTRL0_MX28_PLATE_MASK \
+		(LRADC_CTRL0_MX28_TOUCH_DETECT_ENABLE | \
+		LRADC_CTRL0_MX28_YNNSW | LRADC_CTRL0_MX28_YPNSW | \
+		LRADC_CTRL0_MX28_YPPSW | LRADC_CTRL0_MX28_XNNSW | \
+		LRADC_CTRL0_MX28_XNPSW | LRADC_CTRL0_MX28_XPPSW)
 
 #define	LRADC_CTRL1				0x10
 #define	LRADC_CTRL1_TOUCH_DETECT_IRQ_EN		(1 << 24)
 #define	LRADC_CTRL1_LRADC_IRQ_EN(n)		(1 << ((n) + 16))
-#define	LRADC_CTRL1_LRADC_IRQ_EN_MASK		(0x1fff << 16)
+#define	LRADC_CTRL1_MX28_LRADC_IRQ_EN_MASK	(0x1fff << 16)
 #define	LRADC_CTRL1_LRADC_IRQ_EN_OFFSET		16
 #define	LRADC_CTRL1_TOUCH_DETECT_IRQ		(1 << 8)
 #define	LRADC_CTRL1_LRADC_IRQ(n)		(1 << (n))
-#define	LRADC_CTRL1_LRADC_IRQ_MASK		0x1fff
+#define	LRADC_CTRL1_MX28_LRADC_IRQ_MASK		0x1fff
 #define	LRADC_CTRL1_LRADC_IRQ_OFFSET		0
 
 #define	LRADC_CTRL2				0x20
@@ -267,7 +272,7 @@ static int mxs_lradc_read_raw(struct iio_dev *iio_dev,
 	 * Virtual channel 0 is always used here as the others are always not
 	 * used if doing raw sampling.
 	 */
-	writel(LRADC_CTRL1_LRADC_IRQ_EN_MASK,
+	writel(LRADC_CTRL1_MX28_LRADC_IRQ_EN_MASK,
 		lradc->base + LRADC_CTRL1 + STMP_OFFSET_REG_CLR);
 	writel(0xff, lradc->base + LRADC_CTRL0 + STMP_OFFSET_REG_CLR);
 
@@ -322,9 +327,9 @@ static int mxs_lradc_ts_touched(struct mxs_lradc *lradc)
 	uint32_t reg;
 
 	/* Enable touch detection. */
-	writel(LRADC_CTRL0_PLATE_MASK,
+	writel(LRADC_CTRL0_MX28_PLATE_MASK,
 		lradc->base + LRADC_CTRL0 + STMP_OFFSET_REG_CLR);
-	writel(LRADC_CTRL0_TOUCH_DETECT_ENABLE,
+	writel(LRADC_CTRL0_MX28_TOUCH_DETECT_ENABLE,
 		lradc->base + LRADC_CTRL0 + STMP_OFFSET_REG_SET);
 
 	msleep(LRADC_TS_SAMPLE_DELAY_MS);
@@ -370,21 +375,21 @@ static int32_t mxs_lradc_ts_sample(struct mxs_lradc *lradc,
 	 */
 	switch (plate) {
 	case LRADC_SAMPLE_X:
-		ctrl0 = LRADC_CTRL0_XPPSW | LRADC_CTRL0_XNNSW;
+		ctrl0 = LRADC_CTRL0_MX28_XPPSW | LRADC_CTRL0_MX28_XNNSW;
 		chan = 3;
 		break;
 	case LRADC_SAMPLE_Y:
-		ctrl0 = LRADC_CTRL0_YPPSW | LRADC_CTRL0_YNNSW;
+		ctrl0 = LRADC_CTRL0_MX28_YPPSW | LRADC_CTRL0_MX28_YNNSW;
 		chan = 4;
 		break;
 	case LRADC_SAMPLE_PRESSURE:
-		ctrl0 = LRADC_CTRL0_YPPSW | LRADC_CTRL0_XNNSW;
+		ctrl0 = LRADC_CTRL0_MX28_YPPSW | LRADC_CTRL0_MX28_XNNSW;
 		chan = 5;
 		break;
 	}
 
 	if (change) {
-		writel(LRADC_CTRL0_PLATE_MASK,
+		writel(LRADC_CTRL0_MX28_PLATE_MASK,
 			lradc->base + LRADC_CTRL0 + STMP_OFFSET_REG_CLR);
 		writel(ctrl0, lradc->base + LRADC_CTRL0 + STMP_OFFSET_REG_SET);
 
@@ -445,7 +450,7 @@ static void mxs_lradc_ts_work(struct work_struct *ts_work)
 
 	while (mxs_lradc_ts_touched(lradc)) {
 		/* Disable touch detector so we can sample the touchscreen. */
-		writel(LRADC_CTRL0_TOUCH_DETECT_ENABLE,
+		writel(LRADC_CTRL0_MX28_TOUCH_DETECT_ENABLE,
 			lradc->base + LRADC_CTRL0 + STMP_OFFSET_REG_CLR);
 
 		if (likely(valid)) {
@@ -494,7 +499,7 @@ static int mxs_lradc_ts_open(struct input_dev *dev)
 	lradc->stop_touchscreen = false;
 
 	/* Enable the touch-detect circuitry. */
-	writel(LRADC_CTRL0_TOUCH_DETECT_ENABLE,
+	writel(LRADC_CTRL0_MX28_TOUCH_DETECT_ENABLE,
 		lradc->base + LRADC_CTRL0 + STMP_OFFSET_REG_SET);
 
 	/* Enable the touch-detect IRQ. */
@@ -520,7 +525,7 @@ static void mxs_lradc_ts_close(struct input_dev *dev)
 		lradc->base + LRADC_CTRL1 + STMP_OFFSET_REG_CLR);
 
 	/* Power-down touchscreen touch-detect circuitry. */
-	writel(LRADC_CTRL0_TOUCH_DETECT_ENABLE,
+	writel(LRADC_CTRL0_MX28_TOUCH_DETECT_ENABLE,
 		lradc->base + LRADC_CTRL0 + STMP_OFFSET_REG_CLR);
 }
 
@@ -584,7 +589,7 @@ static irqreturn_t mxs_lradc_handle_irq(int irq, void *data)
 		LRADC_CTRL1_TOUCH_DETECT_IRQ_EN |
 		LRADC_CTRL1_TOUCH_DETECT_IRQ;
 
-	if (!(reg & LRADC_CTRL1_LRADC_IRQ_MASK))
+	if (!(reg & LRADC_CTRL1_MX28_LRADC_IRQ_MASK))
 		return IRQ_NONE;
 
 	/*
@@ -604,7 +609,7 @@ static irqreturn_t mxs_lradc_handle_irq(int irq, void *data)
 	else if (reg & LRADC_CTRL1_LRADC_IRQ(0))
 		complete(&lradc->completion);
 
-	writel(reg & LRADC_CTRL1_LRADC_IRQ_MASK,
+	writel(reg & LRADC_CTRL1_MX28_LRADC_IRQ_MASK,
 		lradc->base + LRADC_CTRL1 + STMP_OFFSET_REG_CLR);
 
 	return IRQ_HANDLED;
@@ -725,7 +730,7 @@ static int mxs_lradc_buffer_preenable(struct iio_dev *iio)
 	if (ret < 0)
 		goto err_buf;
 
-	writel(LRADC_CTRL1_LRADC_IRQ_EN_MASK,
+	writel(LRADC_CTRL1_MX28_LRADC_IRQ_EN_MASK,
 		lradc->base + LRADC_CTRL1 + STMP_OFFSET_REG_CLR);
 	writel(0xff, lradc->base + LRADC_CTRL0 + STMP_OFFSET_REG_CLR);
 
@@ -766,7 +771,7 @@ static int mxs_lradc_buffer_postdisable(struct iio_dev *iio)
 		lradc->base + LRADC_DELAY(0) + STMP_OFFSET_REG_CLR);
 
 	writel(0xff, lradc->base + LRADC_CTRL0 + STMP_OFFSET_REG_CLR);
-	writel(LRADC_CTRL1_LRADC_IRQ_EN_MASK,
+	writel(LRADC_CTRL1_MX28_LRADC_IRQ_EN_MASK,
 		lradc->base + LRADC_CTRL1 + STMP_OFFSET_REG_CLR);
 
 	kfree(lradc->buffer);
@@ -870,11 +875,11 @@ static int mxs_lradc_hw_init(struct mxs_lradc *lradc)
 	writel(0, lradc->base + LRADC_DELAY(3));
 
 	/* Configure the touchscreen type */
-	writel(LRADC_CTRL0_TOUCH_SCREEN_TYPE,
+	writel(LRADC_CTRL0_MX28_TOUCH_SCREEN_TYPE,
 		lradc->base + LRADC_CTRL0 + STMP_OFFSET_REG_CLR);
 
 	if (lradc->use_touchscreen == MXS_LRADC_TOUCHSCREEN_5WIRE) {
-		writel(LRADC_CTRL0_TOUCH_SCREEN_TYPE,
+		writel(LRADC_CTRL0_MX28_TOUCH_SCREEN_TYPE,
 			lradc->base + LRADC_CTRL0 + STMP_OFFSET_REG_SET);
 	}
 
@@ -888,7 +893,7 @@ static void mxs_lradc_hw_stop(struct mxs_lradc *lradc)
 {
 	int i;
 
-	writel(LRADC_CTRL1_LRADC_IRQ_EN_MASK,
+	writel(LRADC_CTRL1_MX28_LRADC_IRQ_EN_MASK,
 		lradc->base + LRADC_CTRL1 + STMP_OFFSET_REG_CLR);
 
 	for (i = 0; i < LRADC_MAX_DELAY_CHANS; i++)
#12 lore raw

PATCH 4/9 Staging/iio/adc/touchscreen/MXS: simplify register access

In reply to Juergen Beisert

Replace the individual register access by a few shared access function to make the code easier to read and in order to add the i.MX23 SoC in the next step.

CC linux-arm-kernel at lists.infradead.org
CC linux-input at vger.kernel.org
CC devel at driverdev.osuosl.org
CC Marek Vasut <[email protected]>
CC Fabio Estevam <[email protected]>
CC Jonathan Cameron <[email protected]>
---
 drivers/staging/iio/adc/mxs-lradc.c | 204 +++++++++++++++++++++---------------
 1 file changed, 120 insertions(+), 84 deletions(-)
drivers/staging/iio/adc/mxs-lradc.c +120 -84
index f2fb10a..dd47ec2 100644
@@ -238,6 +238,56 @@ struct mxs_lradc {
 #define LRADC_RESOLUTION			12
 #define LRADC_SINGLE_SAMPLE_MASK		((1 << LRADC_RESOLUTION) - 1)
 
+static void mxs_lradc_reg_set(struct mxs_lradc *lradc, u32 val, u32 reg)
+{
+	writel(val, lradc->base + reg + STMP_OFFSET_REG_SET);
+}
+
+static void mxs_lradc_reg_clear(struct mxs_lradc *lradc, u32 val, u32 reg)
+{
+	writel(val, lradc->base + reg + STMP_OFFSET_REG_CLR);
+}
+
+static void mxs_lradc_reg_wrt(struct mxs_lradc *lradc, u32 val, u32 reg)
+{
+	writel(val, lradc->base + reg);
+}
+
+static u32 mxs_lradc_plate_mask(struct mxs_lradc *lradc)
+{
+	return LRADC_CTRL0_MX28_PLATE_MASK;
+}
+
+static u32 mxs_lradc_irq_en_mask(struct mxs_lradc *lradc)
+{
+	return LRADC_CTRL1_MX28_LRADC_IRQ_EN_MASK;
+}
+
+static u32 mxs_lradc_irq_mask(struct mxs_lradc *lradc)
+{
+	return LRADC_CTRL1_MX28_LRADC_IRQ_MASK;
+}
+
+static u32 mxs_lradc_touch_detect_bit(struct mxs_lradc *lradc)
+{
+	return LRADC_CTRL0_MX28_TOUCH_DETECT_ENABLE;
+}
+
+static u32 mxs_lradc_drive_x_plate(struct mxs_lradc *lradc)
+{
+	return LRADC_CTRL0_MX28_XPPSW | LRADC_CTRL0_MX28_XNNSW;
+}
+
+static u32 mxs_lradc_drive_y_plate(struct mxs_lradc *lradc)
+{
+	return LRADC_CTRL0_MX28_YPPSW | LRADC_CTRL0_MX28_YNNSW;
+}
+
+static u32 mxs_lradc_drive_pressure(struct mxs_lradc *lradc)
+{
+	return LRADC_CTRL0_MX28_YPPSW | LRADC_CTRL0_MX28_XNNSW;
+}
+
 /*
  * Raw I/O operations
  */
@@ -272,21 +322,19 @@ static int mxs_lradc_read_raw(struct iio_dev *iio_dev,
 	 * Virtual channel 0 is always used here as the others are always not
 	 * used if doing raw sampling.
 	 */
-	writel(LRADC_CTRL1_MX28_LRADC_IRQ_EN_MASK,
-		lradc->base + LRADC_CTRL1 + STMP_OFFSET_REG_CLR);
-	writel(0xff, lradc->base + LRADC_CTRL0 + STMP_OFFSET_REG_CLR);
+	mxs_lradc_reg_clear(lradc, LRADC_CTRL1_MX28_LRADC_IRQ_EN_MASK,
+			LRADC_CTRL1);
+	mxs_lradc_reg_clear(lradc, 0xff, LRADC_CTRL0);
 
 	/* Clean the slot's previous content, then set new one. */
-	writel(LRADC_CTRL4_LRADCSELECT_MASK(0),
-		lradc->base + LRADC_CTRL4 + STMP_OFFSET_REG_CLR);
-	writel(chan->channel, lradc->base + LRADC_CTRL4 + STMP_OFFSET_REG_SET);
+	mxs_lradc_reg_clear(lradc, LRADC_CTRL4_LRADCSELECT_MASK(0), LRADC_CTRL4);
+	mxs_lradc_reg_set(lradc, chan->channel, LRADC_CTRL4);
 
-	writel(0, lradc->base + LRADC_CH(0));
+	mxs_lradc_reg_wrt(lradc, 0, LRADC_CH(0));
 
 	/* Enable the IRQ and start sampling the channel. */
-	writel(LRADC_CTRL1_LRADC_IRQ_EN(0),
-		lradc->base + LRADC_CTRL1 + STMP_OFFSET_REG_SET);
-	writel(1 << 0, lradc->base + LRADC_CTRL0 + STMP_OFFSET_REG_SET);
+	mxs_lradc_reg_set(lradc, LRADC_CTRL1_LRADC_IRQ_EN(0), LRADC_CTRL1);
+	mxs_lradc_reg_set(lradc, 1 << 0, LRADC_CTRL0);
 
 	/* Wait for completion on the channel, 1 second max. */
 	ret = wait_for_completion_killable_timeout(&lradc->completion, HZ);
@@ -300,8 +348,7 @@ static int mxs_lradc_read_raw(struct iio_dev *iio_dev,
 	ret = IIO_VAL_INT;
 
 err:
-	writel(LRADC_CTRL1_LRADC_IRQ_EN(0),
-		lradc->base + LRADC_CTRL1 + STMP_OFFSET_REG_CLR);
+	mxs_lradc_reg_clear(lradc, LRADC_CTRL1_LRADC_IRQ_EN(0), LRADC_CTRL1);
 
 	mutex_unlock(&lradc->lock);
 
@@ -327,10 +374,9 @@ static int mxs_lradc_ts_touched(struct mxs_lradc *lradc)
 	uint32_t reg;
 
 	/* Enable touch detection. */
-	writel(LRADC_CTRL0_MX28_PLATE_MASK,
-		lradc->base + LRADC_CTRL0 + STMP_OFFSET_REG_CLR);
-	writel(LRADC_CTRL0_MX28_TOUCH_DETECT_ENABLE,
-		lradc->base + LRADC_CTRL0 + STMP_OFFSET_REG_SET);
+	mxs_lradc_reg_clear(lradc, mxs_lradc_plate_mask(lradc), LRADC_CTRL0);
+	mxs_lradc_reg_set(lradc, mxs_lradc_touch_detect_bit(lradc),
+								LRADC_CTRL0);
 
 	msleep(LRADC_TS_SAMPLE_DELAY_MS);
 
@@ -375,32 +421,33 @@ static int32_t mxs_lradc_ts_sample(struct mxs_lradc *lradc,
 	 */
 	switch (plate) {
 	case LRADC_SAMPLE_X:
-		ctrl0 = LRADC_CTRL0_MX28_XPPSW | LRADC_CTRL0_MX28_XNNSW;
+		ctrl0 = mxs_lradc_drive_x_plate(lradc);
 		chan = 3;
 		break;
 	case LRADC_SAMPLE_Y:
-		ctrl0 = LRADC_CTRL0_MX28_YPPSW | LRADC_CTRL0_MX28_YNNSW;
+		ctrl0 = mxs_lradc_drive_y_plate(lradc);
 		chan = 4;
 		break;
 	case LRADC_SAMPLE_PRESSURE:
-		ctrl0 = LRADC_CTRL0_MX28_YPPSW | LRADC_CTRL0_MX28_XNNSW;
+		ctrl0 = mxs_lradc_drive_pressure(lradc);
 		chan = 5;
 		break;
 	}
 
 	if (change) {
-		writel(LRADC_CTRL0_MX28_PLATE_MASK,
-			lradc->base + LRADC_CTRL0 + STMP_OFFSET_REG_CLR);
-		writel(ctrl0, lradc->base + LRADC_CTRL0 + STMP_OFFSET_REG_SET);
-
-		writel(LRADC_CTRL4_LRADCSELECT_MASK(slot),
-			lradc->base + LRADC_CTRL4 + STMP_OFFSET_REG_CLR);
-		writel(chan << LRADC_CTRL4_LRADCSELECT_OFFSET(slot),
-			lradc->base + LRADC_CTRL4 + STMP_OFFSET_REG_SET);
+		mxs_lradc_reg_clear(lradc, mxs_lradc_plate_mask(lradc),
+						LRADC_CTRL0);
+		mxs_lradc_reg_set(lradc, ctrl0, LRADC_CTRL0);
+
+		mxs_lradc_reg_clear(lradc, LRADC_CTRL4_LRADCSELECT_MASK(slot),
+						LRADC_CTRL4);
+		mxs_lradc_reg_set(lradc,
+				chan << LRADC_CTRL4_LRADCSELECT_OFFSET(slot),
+				LRADC_CTRL4);
 	}
 
-	writel(0xffffffff, lradc->base + LRADC_CH(slot) + STMP_OFFSET_REG_CLR);
-	writel(1 << slot, lradc->base + LRADC_CTRL0 + STMP_OFFSET_REG_SET);
+	mxs_lradc_reg_clear(lradc, 0xffffffff, LRADC_CH(slot));
+	mxs_lradc_reg_set(lradc, 1 << slot, LRADC_CTRL0);
 
 	delay = jiffies + msecs_to_jiffies(LRADC_TS_SAMPLE_DELAY_MS);
 	do {
@@ -410,8 +457,7 @@ static int32_t mxs_lradc_ts_sample(struct mxs_lradc *lradc,
 			break;
 	} while (time_before(jiff, delay));
 
-	writel(LRADC_CTRL1_LRADC_IRQ(slot),
-		lradc->base + LRADC_CTRL1 + STMP_OFFSET_REG_CLR);
+	mxs_lradc_reg_clear(lradc, LRADC_CTRL1_LRADC_IRQ(slot), LRADC_CTRL1);
 
 	if (time_after_eq(jiff, delay))
 		return -ETIMEDOUT;
@@ -450,8 +496,8 @@ static void mxs_lradc_ts_work(struct work_struct *ts_work)
 
 	while (mxs_lradc_ts_touched(lradc)) {
 		/* Disable touch detector so we can sample the touchscreen. */
-		writel(LRADC_CTRL0_MX28_TOUCH_DETECT_ENABLE,
-			lradc->base + LRADC_CTRL0 + STMP_OFFSET_REG_CLR);
+		mxs_lradc_reg_clear(lradc, mxs_lradc_touch_detect_bit(lradc),
+						LRADC_CTRL0);
 
 		if (likely(valid)) {
 			input_report_abs(lradc->ts_input, ABS_X, val_x);
@@ -485,10 +531,8 @@ static void mxs_lradc_ts_work(struct work_struct *ts_work)
 		return;
 
 	/* Restart the touchscreen interrupts. */
-	writel(LRADC_CTRL1_TOUCH_DETECT_IRQ,
-		lradc->base + LRADC_CTRL1 + STMP_OFFSET_REG_CLR);
-	writel(LRADC_CTRL1_TOUCH_DETECT_IRQ_EN,
-		lradc->base + LRADC_CTRL1 + STMP_OFFSET_REG_SET);
+	mxs_lradc_reg_clear(lradc, LRADC_CTRL1_TOUCH_DETECT_IRQ, LRADC_CTRL1);
+	mxs_lradc_reg_set(lradc, LRADC_CTRL1_TOUCH_DETECT_IRQ_EN, LRADC_CTRL1);
 }
 
 static int mxs_lradc_ts_open(struct input_dev *dev)
@@ -499,12 +543,11 @@ static int mxs_lradc_ts_open(struct input_dev *dev)
 	lradc->stop_touchscreen = false;
 
 	/* Enable the touch-detect circuitry. */
-	writel(LRADC_CTRL0_MX28_TOUCH_DETECT_ENABLE,
-		lradc->base + LRADC_CTRL0 + STMP_OFFSET_REG_SET);
+	mxs_lradc_reg_set(lradc, mxs_lradc_touch_detect_bit(lradc),
+						LRADC_CTRL0);
 
 	/* Enable the touch-detect IRQ. */
-	writel(LRADC_CTRL1_TOUCH_DETECT_IRQ_EN,
-		lradc->base + LRADC_CTRL1 + STMP_OFFSET_REG_SET);
+	mxs_lradc_reg_set(lradc, LRADC_CTRL1_TOUCH_DETECT_IRQ_EN, LRADC_CTRL1);
 
 	return 0;
 }
@@ -521,12 +564,11 @@ static void mxs_lradc_ts_close(struct input_dev *dev)
 	cancel_work_sync(&lradc->ts_work);
 
 	/* Disable touchscreen touch-detect IRQ. */
-	writel(LRADC_CTRL1_TOUCH_DETECT_IRQ_EN,
-		lradc->base + LRADC_CTRL1 + STMP_OFFSET_REG_CLR);
+	mxs_lradc_reg_clear(lradc, LRADC_CTRL1_TOUCH_DETECT_IRQ_EN,
+						LRADC_CTRL1);
 
 	/* Power-down touchscreen touch-detect circuitry. */
-	writel(LRADC_CTRL0_MX28_TOUCH_DETECT_ENABLE,
-		lradc->base + LRADC_CTRL0 + STMP_OFFSET_REG_CLR);
+	mxs_lradc_reg_clear(lradc, mxs_lradc_touch_detect_bit(lradc), LRADC_CTRL0);
 }
 
 static int mxs_lradc_ts_register(struct mxs_lradc *lradc)
@@ -589,7 +631,7 @@ static irqreturn_t mxs_lradc_handle_irq(int irq, void *data)
 		LRADC_CTRL1_TOUCH_DETECT_IRQ_EN |
 		LRADC_CTRL1_TOUCH_DETECT_IRQ;
 
-	if (!(reg & LRADC_CTRL1_MX28_LRADC_IRQ_MASK))
+	if (!(reg & mxs_lradc_irq_mask(lradc)))
 		return IRQ_NONE;
 
 	/*
@@ -598,8 +640,7 @@ static irqreturn_t mxs_lradc_handle_irq(int irq, void *data)
 	 * it ASAP
 	 */
 	if (reg & LRADC_CTRL1_TOUCH_DETECT_IRQ) {
-		writel(ts_irq_mask,
-			lradc->base + LRADC_CTRL1 + STMP_OFFSET_REG_CLR);
+		mxs_lradc_reg_clear(lradc, ts_irq_mask, LRADC_CTRL1);
 		if (!lradc->stop_touchscreen)
 			schedule_work(&lradc->ts_work);
 	}
@@ -609,8 +650,7 @@ static irqreturn_t mxs_lradc_handle_irq(int irq, void *data)
 	else if (reg & LRADC_CTRL1_LRADC_IRQ(0))
 		complete(&lradc->completion);
 
-	writel(reg & LRADC_CTRL1_MX28_LRADC_IRQ_MASK,
-		lradc->base + LRADC_CTRL1 + STMP_OFFSET_REG_CLR);
+	mxs_lradc_reg_clear(lradc, reg & mxs_lradc_irq_mask(lradc), LRADC_CTRL1);
 
 	return IRQ_HANDLED;
 }
@@ -629,7 +669,7 @@ static irqreturn_t mxs_lradc_trigger_handler(int irq, void *p)
 
 	for_each_set_bit(i, iio->active_scan_mask, LRADC_MAX_TOTAL_CHANS) {
 		lradc->buffer[j] = readl(lradc->base + LRADC_CH(j));
-		writel(chan_value, lradc->base + LRADC_CH(j));
+		mxs_lradc_reg_wrt(lradc, chan_value, LRADC_CH(j));
 		lradc->buffer[j] &= LRADC_CH_VALUE_MASK;
 		lradc->buffer[j] /= LRADC_DELAY_TIMER_LOOP;
 		j++;
@@ -654,7 +694,7 @@ static int mxs_lradc_configure_trigger(struct iio_trigger *trig, bool state)
 	struct mxs_lradc *lradc = iio_priv(iio);
 	const uint32_t st = state ? STMP_OFFSET_REG_SET : STMP_OFFSET_REG_CLR;
 
-	writel(LRADC_DELAY_KICK, lradc->base + LRADC_DELAY(0) + st);
+	mxs_lradc_reg_wrt(lradc, LRADC_DELAY_KICK, LRADC_DELAY(0) + st);
 
 	return 0;
 }
@@ -730,29 +770,26 @@ static int mxs_lradc_buffer_preenable(struct iio_dev *iio)
 	if (ret < 0)
 		goto err_buf;
 
-	writel(LRADC_CTRL1_MX28_LRADC_IRQ_EN_MASK,
-		lradc->base + LRADC_CTRL1 + STMP_OFFSET_REG_CLR);
-	writel(0xff, lradc->base + LRADC_CTRL0 + STMP_OFFSET_REG_CLR);
+	mxs_lradc_reg_clear(lradc, LRADC_CTRL1_MX28_LRADC_IRQ_EN_MASK,
+							LRADC_CTRL1);
+	mxs_lradc_reg_clear(lradc, 0xff, LRADC_CTRL0);
 
 	for_each_set_bit(chan, iio->active_scan_mask, LRADC_MAX_TOTAL_CHANS) {
 		ctrl4_set |= chan << LRADC_CTRL4_LRADCSELECT_OFFSET(ofs);
 		ctrl4_clr |= LRADC_CTRL4_LRADCSELECT_MASK(ofs);
 		ctrl1_irq |= LRADC_CTRL1_LRADC_IRQ_EN(ofs);
-		writel(chan_value, lradc->base + LRADC_CH(ofs));
+		mxs_lradc_reg_wrt(lradc, chan_value, LRADC_CH(ofs));
 		bitmap_set(&enable, ofs, 1);
 		ofs++;
 	}
 
-	writel(LRADC_DELAY_TRIGGER_LRADCS_MASK | LRADC_DELAY_KICK,
-		lradc->base + LRADC_DELAY(0) + STMP_OFFSET_REG_CLR);
-
-	writel(ctrl4_clr, lradc->base + LRADC_CTRL4 + STMP_OFFSET_REG_CLR);
-	writel(ctrl4_set, lradc->base + LRADC_CTRL4 + STMP_OFFSET_REG_SET);
-
-	writel(ctrl1_irq, lradc->base + LRADC_CTRL1 + STMP_OFFSET_REG_SET);
-
-	writel(enable << LRADC_DELAY_TRIGGER_LRADCS_OFFSET,
-		lradc->base + LRADC_DELAY(0) + STMP_OFFSET_REG_SET);
+	mxs_lradc_reg_clear(lradc, LRADC_DELAY_TRIGGER_LRADCS_MASK |
+					LRADC_DELAY_KICK, LRADC_DELAY(0));
+	mxs_lradc_reg_clear(lradc, ctrl4_clr, LRADC_CTRL4);
+	mxs_lradc_reg_set(lradc, ctrl4_set, LRADC_CTRL4);
+	mxs_lradc_reg_set(lradc, ctrl1_irq, LRADC_CTRL1);
+	mxs_lradc_reg_set(lradc, enable << LRADC_DELAY_TRIGGER_LRADCS_OFFSET,
+					LRADC_DELAY(0));
 
 	return 0;
 
@@ -767,12 +804,12 @@ static int mxs_lradc_buffer_postdisable(struct iio_dev *iio)
 {
 	struct mxs_lradc *lradc = iio_priv(iio);
 
-	writel(LRADC_DELAY_TRIGGER_LRADCS_MASK | LRADC_DELAY_KICK,
-		lradc->base + LRADC_DELAY(0) + STMP_OFFSET_REG_CLR);
+	mxs_lradc_reg_clear(lradc, LRADC_DELAY_TRIGGER_LRADCS_MASK |
+					LRADC_DELAY_KICK, LRADC_DELAY(0));
 
-	writel(0xff, lradc->base + LRADC_CTRL0 + STMP_OFFSET_REG_CLR);
-	writel(LRADC_CTRL1_MX28_LRADC_IRQ_EN_MASK,
-		lradc->base + LRADC_CTRL1 + STMP_OFFSET_REG_CLR);
+	mxs_lradc_reg_clear(lradc, 0xff, LRADC_CTRL0);
+	mxs_lradc_reg_clear(lradc, LRADC_CTRL1_MX28_LRADC_IRQ_EN_MASK,
+					LRADC_CTRL1);
 
 	kfree(lradc->buffer);
 	mutex_unlock(&lradc->lock);
@@ -867,24 +904,24 @@ static int mxs_lradc_hw_init(struct mxs_lradc *lradc)
 		return ret;
 
 	/* Configure DELAY CHANNEL 0 for generic ADC sampling. */
-	writel(adc_cfg, lradc->base + LRADC_DELAY(0));
+	mxs_lradc_reg_wrt(lradc, adc_cfg, LRADC_DELAY(0));
 
 	/* Disable remaining DELAY CHANNELs */
-	writel(0, lradc->base + LRADC_DELAY(1));
-	writel(0, lradc->base + LRADC_DELAY(2));
-	writel(0, lradc->base + LRADC_DELAY(3));
+	mxs_lradc_reg_wrt(lradc, 0, LRADC_DELAY(1));
+	mxs_lradc_reg_wrt(lradc, 0, LRADC_DELAY(2));
+	mxs_lradc_reg_wrt(lradc, 0, LRADC_DELAY(3));
 
 	/* Configure the touchscreen type */
-	writel(LRADC_CTRL0_MX28_TOUCH_SCREEN_TYPE,
-		lradc->base + LRADC_CTRL0 + STMP_OFFSET_REG_CLR);
+	mxs_lradc_reg_clear(lradc, LRADC_CTRL0_MX28_TOUCH_SCREEN_TYPE,
+							LRADC_CTRL0);
 
-	if (lradc->use_touchscreen == MXS_LRADC_TOUCHSCREEN_5WIRE) {
-		writel(LRADC_CTRL0_MX28_TOUCH_SCREEN_TYPE,
-			lradc->base + LRADC_CTRL0 + STMP_OFFSET_REG_SET);
+	if (lradc->use_touchscreen == MXS_LRADC_TOUCHSCREEN_5WIRE)
+		mxs_lradc_reg_set(lradc, LRADC_CTRL0_MX28_TOUCH_SCREEN_TYPE,
+				LRADC_CTRL0);
 	}
 
 	/* Start internal temperature sensing. */
-	writel(0, lradc->base + LRADC_CTRL2);
+	mxs_lradc_reg_wrt(lradc, 0, LRADC_CTRL2);
 
 	return 0;
 }
@@ -893,11 +930,10 @@ static void mxs_lradc_hw_stop(struct mxs_lradc *lradc)
 {
 	int i;
 
-	writel(LRADC_CTRL1_MX28_LRADC_IRQ_EN_MASK,
-		lradc->base + LRADC_CTRL1 + STMP_OFFSET_REG_CLR);
+	mxs_lradc_reg_clear(lradc, mxs_lradc_irq_en_mask(lradc), LRADC_CTRL1);
 
 	for (i = 0; i < LRADC_MAX_DELAY_CHANS; i++)
-		writel(0, lradc->base + LRADC_DELAY(i));
+		mxs_lradc_reg_wrt(lradc, 0, LRADC_DELAY(i));
 }
 
 static const struct of_device_id mxs_lradc_dt_ids[] = {
Signature · 1 line
1.8.4.rc3
maintainer Applied
#13 lore raw

PATCH 4/9 Staging/iio/adc/touchscreen/MXS: simplify register access

Quoted 10 lines · Juergen Beisert

Replace the individual register access by a few shared access function to make the code easier to read and in order to add the i.MX23 SoC in the next step.

Applied to the togreg branch of iio.git

Thanks,

Jonathan

Quoted 388 lines
---
 drivers/staging/iio/adc/mxs-lradc.c | 204 +++++++++++++++++++++---------------
 1 file changed, 120 insertions(+), 84 deletions(-)
drivers/staging/iio/adc/mxs-lradc.c +120 -84
index f2fb10a..dd47ec2 100644
@@ -238,6 +238,56 @@ struct mxs_lradc {
 #define LRADC_RESOLUTION			12
 #define LRADC_SINGLE_SAMPLE_MASK		((1 << LRADC_RESOLUTION) - 1)
 
+static void mxs_lradc_reg_set(struct mxs_lradc *lradc, u32 val, u32 reg)
+{
+	writel(val, lradc->base + reg + STMP_OFFSET_REG_SET);
+}
+
+static void mxs_lradc_reg_clear(struct mxs_lradc *lradc, u32 val, u32 reg)
+{
+	writel(val, lradc->base + reg + STMP_OFFSET_REG_CLR);
+}
+
+static void mxs_lradc_reg_wrt(struct mxs_lradc *lradc, u32 val, u32 reg)
+{
+	writel(val, lradc->base + reg);
+}
+
+static u32 mxs_lradc_plate_mask(struct mxs_lradc *lradc)
+{
+	return LRADC_CTRL0_MX28_PLATE_MASK;
+}
+
+static u32 mxs_lradc_irq_en_mask(struct mxs_lradc *lradc)
+{
+	return LRADC_CTRL1_MX28_LRADC_IRQ_EN_MASK;
+}
+
+static u32 mxs_lradc_irq_mask(struct mxs_lradc *lradc)
+{
+	return LRADC_CTRL1_MX28_LRADC_IRQ_MASK;
+}
+
+static u32 mxs_lradc_touch_detect_bit(struct mxs_lradc *lradc)
+{
+	return LRADC_CTRL0_MX28_TOUCH_DETECT_ENABLE;
+}
+
+static u32 mxs_lradc_drive_x_plate(struct mxs_lradc *lradc)
+{
+	return LRADC_CTRL0_MX28_XPPSW | LRADC_CTRL0_MX28_XNNSW;
+}
+
+static u32 mxs_lradc_drive_y_plate(struct mxs_lradc *lradc)
+{
+	return LRADC_CTRL0_MX28_YPPSW | LRADC_CTRL0_MX28_YNNSW;
+}
+
+static u32 mxs_lradc_drive_pressure(struct mxs_lradc *lradc)
+{
+	return LRADC_CTRL0_MX28_YPPSW | LRADC_CTRL0_MX28_XNNSW;
+}
+
 /*
  * Raw I/O operations
  */
@@ -272,21 +322,19 @@ static int mxs_lradc_read_raw(struct iio_dev *iio_dev,
 	 * Virtual channel 0 is always used here as the others are always not
 	 * used if doing raw sampling.
 	 */
-	writel(LRADC_CTRL1_MX28_LRADC_IRQ_EN_MASK,
-		lradc->base + LRADC_CTRL1 + STMP_OFFSET_REG_CLR);
-	writel(0xff, lradc->base + LRADC_CTRL0 + STMP_OFFSET_REG_CLR);
+	mxs_lradc_reg_clear(lradc, LRADC_CTRL1_MX28_LRADC_IRQ_EN_MASK,
+			LRADC_CTRL1);
+	mxs_lradc_reg_clear(lradc, 0xff, LRADC_CTRL0);
 
 	/* Clean the slot's previous content, then set new one. */
-	writel(LRADC_CTRL4_LRADCSELECT_MASK(0),
-		lradc->base + LRADC_CTRL4 + STMP_OFFSET_REG_CLR);
-	writel(chan->channel, lradc->base + LRADC_CTRL4 + STMP_OFFSET_REG_SET);
+	mxs_lradc_reg_clear(lradc, LRADC_CTRL4_LRADCSELECT_MASK(0), LRADC_CTRL4);
+	mxs_lradc_reg_set(lradc, chan->channel, LRADC_CTRL4);
 
-	writel(0, lradc->base + LRADC_CH(0));
+	mxs_lradc_reg_wrt(lradc, 0, LRADC_CH(0));
 
 	/* Enable the IRQ and start sampling the channel. */
-	writel(LRADC_CTRL1_LRADC_IRQ_EN(0),
-		lradc->base + LRADC_CTRL1 + STMP_OFFSET_REG_SET);
-	writel(1 << 0, lradc->base + LRADC_CTRL0 + STMP_OFFSET_REG_SET);
+	mxs_lradc_reg_set(lradc, LRADC_CTRL1_LRADC_IRQ_EN(0), LRADC_CTRL1);
+	mxs_lradc_reg_set(lradc, 1 << 0, LRADC_CTRL0);
 
 	/* Wait for completion on the channel, 1 second max. */
 	ret = wait_for_completion_killable_timeout(&lradc->completion, HZ);
@@ -300,8 +348,7 @@ static int mxs_lradc_read_raw(struct iio_dev *iio_dev,
 	ret = IIO_VAL_INT;
 
 err:
-	writel(LRADC_CTRL1_LRADC_IRQ_EN(0),
-		lradc->base + LRADC_CTRL1 + STMP_OFFSET_REG_CLR);
+	mxs_lradc_reg_clear(lradc, LRADC_CTRL1_LRADC_IRQ_EN(0), LRADC_CTRL1);
 
 	mutex_unlock(&lradc->lock);
 
@@ -327,10 +374,9 @@ static int mxs_lradc_ts_touched(struct mxs_lradc *lradc)
 	uint32_t reg;
 
 	/* Enable touch detection. */
-	writel(LRADC_CTRL0_MX28_PLATE_MASK,
-		lradc->base + LRADC_CTRL0 + STMP_OFFSET_REG_CLR);
-	writel(LRADC_CTRL0_MX28_TOUCH_DETECT_ENABLE,
-		lradc->base + LRADC_CTRL0 + STMP_OFFSET_REG_SET);
+	mxs_lradc_reg_clear(lradc, mxs_lradc_plate_mask(lradc), LRADC_CTRL0);
+	mxs_lradc_reg_set(lradc, mxs_lradc_touch_detect_bit(lradc),
+								LRADC_CTRL0);
 
 	msleep(LRADC_TS_SAMPLE_DELAY_MS);
 
@@ -375,32 +421,33 @@ static int32_t mxs_lradc_ts_sample(struct mxs_lradc *lradc,
 	 */
 	switch (plate) {
 	case LRADC_SAMPLE_X:
-		ctrl0 = LRADC_CTRL0_MX28_XPPSW | LRADC_CTRL0_MX28_XNNSW;
+		ctrl0 = mxs_lradc_drive_x_plate(lradc);
 		chan = 3;
 		break;
 	case LRADC_SAMPLE_Y:
-		ctrl0 = LRADC_CTRL0_MX28_YPPSW | LRADC_CTRL0_MX28_YNNSW;
+		ctrl0 = mxs_lradc_drive_y_plate(lradc);
 		chan = 4;
 		break;
 	case LRADC_SAMPLE_PRESSURE:
-		ctrl0 = LRADC_CTRL0_MX28_YPPSW | LRADC_CTRL0_MX28_XNNSW;
+		ctrl0 = mxs_lradc_drive_pressure(lradc);
 		chan = 5;
 		break;
 	}
 
 	if (change) {
-		writel(LRADC_CTRL0_MX28_PLATE_MASK,
-			lradc->base + LRADC_CTRL0 + STMP_OFFSET_REG_CLR);
-		writel(ctrl0, lradc->base + LRADC_CTRL0 + STMP_OFFSET_REG_SET);
-
-		writel(LRADC_CTRL4_LRADCSELECT_MASK(slot),
-			lradc->base + LRADC_CTRL4 + STMP_OFFSET_REG_CLR);
-		writel(chan << LRADC_CTRL4_LRADCSELECT_OFFSET(slot),
-			lradc->base + LRADC_CTRL4 + STMP_OFFSET_REG_SET);
+		mxs_lradc_reg_clear(lradc, mxs_lradc_plate_mask(lradc),
+						LRADC_CTRL0);
+		mxs_lradc_reg_set(lradc, ctrl0, LRADC_CTRL0);
+
+		mxs_lradc_reg_clear(lradc, LRADC_CTRL4_LRADCSELECT_MASK(slot),
+						LRADC_CTRL4);
+		mxs_lradc_reg_set(lradc,
+				chan << LRADC_CTRL4_LRADCSELECT_OFFSET(slot),
+				LRADC_CTRL4);
 	}
 
-	writel(0xffffffff, lradc->base + LRADC_CH(slot) + STMP_OFFSET_REG_CLR);
-	writel(1 << slot, lradc->base + LRADC_CTRL0 + STMP_OFFSET_REG_SET);
+	mxs_lradc_reg_clear(lradc, 0xffffffff, LRADC_CH(slot));
+	mxs_lradc_reg_set(lradc, 1 << slot, LRADC_CTRL0);
 
 	delay = jiffies + msecs_to_jiffies(LRADC_TS_SAMPLE_DELAY_MS);
 	do {
@@ -410,8 +457,7 @@ static int32_t mxs_lradc_ts_sample(struct mxs_lradc *lradc,
 			break;
 	} while (time_before(jiff, delay));
 
-	writel(LRADC_CTRL1_LRADC_IRQ(slot),
-		lradc->base + LRADC_CTRL1 + STMP_OFFSET_REG_CLR);
+	mxs_lradc_reg_clear(lradc, LRADC_CTRL1_LRADC_IRQ(slot), LRADC_CTRL1);
 
 	if (time_after_eq(jiff, delay))
 		return -ETIMEDOUT;
@@ -450,8 +496,8 @@ static void mxs_lradc_ts_work(struct work_struct *ts_work)
 
 	while (mxs_lradc_ts_touched(lradc)) {
 		/* Disable touch detector so we can sample the touchscreen. */
-		writel(LRADC_CTRL0_MX28_TOUCH_DETECT_ENABLE,
-			lradc->base + LRADC_CTRL0 + STMP_OFFSET_REG_CLR);
+		mxs_lradc_reg_clear(lradc, mxs_lradc_touch_detect_bit(lradc),
+						LRADC_CTRL0);
 
 		if (likely(valid)) {
 			input_report_abs(lradc->ts_input, ABS_X, val_x);
@@ -485,10 +531,8 @@ static void mxs_lradc_ts_work(struct work_struct *ts_work)
 		return;
 
 	/* Restart the touchscreen interrupts. */
-	writel(LRADC_CTRL1_TOUCH_DETECT_IRQ,
-		lradc->base + LRADC_CTRL1 + STMP_OFFSET_REG_CLR);
-	writel(LRADC_CTRL1_TOUCH_DETECT_IRQ_EN,
-		lradc->base + LRADC_CTRL1 + STMP_OFFSET_REG_SET);
+	mxs_lradc_reg_clear(lradc, LRADC_CTRL1_TOUCH_DETECT_IRQ, LRADC_CTRL1);
+	mxs_lradc_reg_set(lradc, LRADC_CTRL1_TOUCH_DETECT_IRQ_EN, LRADC_CTRL1);
 }
 
 static int mxs_lradc_ts_open(struct input_dev *dev)
@@ -499,12 +543,11 @@ static int mxs_lradc_ts_open(struct input_dev *dev)
 	lradc->stop_touchscreen = false;
 
 	/* Enable the touch-detect circuitry. */
-	writel(LRADC_CTRL0_MX28_TOUCH_DETECT_ENABLE,
-		lradc->base + LRADC_CTRL0 + STMP_OFFSET_REG_SET);
+	mxs_lradc_reg_set(lradc, mxs_lradc_touch_detect_bit(lradc),
+						LRADC_CTRL0);
 
 	/* Enable the touch-detect IRQ. */
-	writel(LRADC_CTRL1_TOUCH_DETECT_IRQ_EN,
-		lradc->base + LRADC_CTRL1 + STMP_OFFSET_REG_SET);
+	mxs_lradc_reg_set(lradc, LRADC_CTRL1_TOUCH_DETECT_IRQ_EN, LRADC_CTRL1);
 
 	return 0;
 }
@@ -521,12 +564,11 @@ static void mxs_lradc_ts_close(struct input_dev *dev)
 	cancel_work_sync(&lradc->ts_work);
 
 	/* Disable touchscreen touch-detect IRQ. */
-	writel(LRADC_CTRL1_TOUCH_DETECT_IRQ_EN,
-		lradc->base + LRADC_CTRL1 + STMP_OFFSET_REG_CLR);
+	mxs_lradc_reg_clear(lradc, LRADC_CTRL1_TOUCH_DETECT_IRQ_EN,
+						LRADC_CTRL1);
 
 	/* Power-down touchscreen touch-detect circuitry. */
-	writel(LRADC_CTRL0_MX28_TOUCH_DETECT_ENABLE,
-		lradc->base + LRADC_CTRL0 + STMP_OFFSET_REG_CLR);
+	mxs_lradc_reg_clear(lradc, mxs_lradc_touch_detect_bit(lradc), LRADC_CTRL0);
 }
 
 static int mxs_lradc_ts_register(struct mxs_lradc *lradc)
@@ -589,7 +631,7 @@ static irqreturn_t mxs_lradc_handle_irq(int irq, void *data)
 		LRADC_CTRL1_TOUCH_DETECT_IRQ_EN |
 		LRADC_CTRL1_TOUCH_DETECT_IRQ;
 
-	if (!(reg & LRADC_CTRL1_MX28_LRADC_IRQ_MASK))
+	if (!(reg & mxs_lradc_irq_mask(lradc)))
 		return IRQ_NONE;
 
 	/*
@@ -598,8 +640,7 @@ static irqreturn_t mxs_lradc_handle_irq(int irq, void *data)
 	 * it ASAP
 	 */
 	if (reg & LRADC_CTRL1_TOUCH_DETECT_IRQ) {
-		writel(ts_irq_mask,
-			lradc->base + LRADC_CTRL1 + STMP_OFFSET_REG_CLR);
+		mxs_lradc_reg_clear(lradc, ts_irq_mask, LRADC_CTRL1);
 		if (!lradc->stop_touchscreen)
 			schedule_work(&lradc->ts_work);
 	}
@@ -609,8 +650,7 @@ static irqreturn_t mxs_lradc_handle_irq(int irq, void *data)
 	else if (reg & LRADC_CTRL1_LRADC_IRQ(0))
 		complete(&lradc->completion);
 
-	writel(reg & LRADC_CTRL1_MX28_LRADC_IRQ_MASK,
-		lradc->base + LRADC_CTRL1 + STMP_OFFSET_REG_CLR);
+	mxs_lradc_reg_clear(lradc, reg & mxs_lradc_irq_mask(lradc), LRADC_CTRL1);
 
 	return IRQ_HANDLED;
 }
@@ -629,7 +669,7 @@ static irqreturn_t mxs_lradc_trigger_handler(int irq, void *p)
 
 	for_each_set_bit(i, iio->active_scan_mask, LRADC_MAX_TOTAL_CHANS) {
 		lradc->buffer[j] = readl(lradc->base + LRADC_CH(j));
-		writel(chan_value, lradc->base + LRADC_CH(j));
+		mxs_lradc_reg_wrt(lradc, chan_value, LRADC_CH(j));
 		lradc->buffer[j] &= LRADC_CH_VALUE_MASK;
 		lradc->buffer[j] /= LRADC_DELAY_TIMER_LOOP;
 		j++;
@@ -654,7 +694,7 @@ static int mxs_lradc_configure_trigger(struct iio_trigger *trig, bool state)
 	struct mxs_lradc *lradc = iio_priv(iio);
 	const uint32_t st = state ? STMP_OFFSET_REG_SET : STMP_OFFSET_REG_CLR;
 
-	writel(LRADC_DELAY_KICK, lradc->base + LRADC_DELAY(0) + st);
+	mxs_lradc_reg_wrt(lradc, LRADC_DELAY_KICK, LRADC_DELAY(0) + st);
 
 	return 0;
 }
@@ -730,29 +770,26 @@ static int mxs_lradc_buffer_preenable(struct iio_dev *iio)
 	if (ret < 0)
 		goto err_buf;
 
-	writel(LRADC_CTRL1_MX28_LRADC_IRQ_EN_MASK,
-		lradc->base + LRADC_CTRL1 + STMP_OFFSET_REG_CLR);
-	writel(0xff, lradc->base + LRADC_CTRL0 + STMP_OFFSET_REG_CLR);
+	mxs_lradc_reg_clear(lradc, LRADC_CTRL1_MX28_LRADC_IRQ_EN_MASK,
+							LRADC_CTRL1);
+	mxs_lradc_reg_clear(lradc, 0xff, LRADC_CTRL0);
 
 	for_each_set_bit(chan, iio->active_scan_mask, LRADC_MAX_TOTAL_CHANS) {
 		ctrl4_set |= chan << LRADC_CTRL4_LRADCSELECT_OFFSET(ofs);
 		ctrl4_clr |= LRADC_CTRL4_LRADCSELECT_MASK(ofs);
 		ctrl1_irq |= LRADC_CTRL1_LRADC_IRQ_EN(ofs);
-		writel(chan_value, lradc->base + LRADC_CH(ofs));
+		mxs_lradc_reg_wrt(lradc, chan_value, LRADC_CH(ofs));
 		bitmap_set(&enable, ofs, 1);
 		ofs++;
 	}
 
-	writel(LRADC_DELAY_TRIGGER_LRADCS_MASK | LRADC_DELAY_KICK,
-		lradc->base + LRADC_DELAY(0) + STMP_OFFSET_REG_CLR);
-
-	writel(ctrl4_clr, lradc->base + LRADC_CTRL4 + STMP_OFFSET_REG_CLR);
-	writel(ctrl4_set, lradc->base + LRADC_CTRL4 + STMP_OFFSET_REG_SET);
-
-	writel(ctrl1_irq, lradc->base + LRADC_CTRL1 + STMP_OFFSET_REG_SET);
-
-	writel(enable << LRADC_DELAY_TRIGGER_LRADCS_OFFSET,
-		lradc->base + LRADC_DELAY(0) + STMP_OFFSET_REG_SET);
+	mxs_lradc_reg_clear(lradc, LRADC_DELAY_TRIGGER_LRADCS_MASK |
+					LRADC_DELAY_KICK, LRADC_DELAY(0));
+	mxs_lradc_reg_clear(lradc, ctrl4_clr, LRADC_CTRL4);
+	mxs_lradc_reg_set(lradc, ctrl4_set, LRADC_CTRL4);
+	mxs_lradc_reg_set(lradc, ctrl1_irq, LRADC_CTRL1);
+	mxs_lradc_reg_set(lradc, enable << LRADC_DELAY_TRIGGER_LRADCS_OFFSET,
+					LRADC_DELAY(0));
 
 	return 0;
 
@@ -767,12 +804,12 @@ static int mxs_lradc_buffer_postdisable(struct iio_dev *iio)
 {
 	struct mxs_lradc *lradc = iio_priv(iio);
 
-	writel(LRADC_DELAY_TRIGGER_LRADCS_MASK | LRADC_DELAY_KICK,
-		lradc->base + LRADC_DELAY(0) + STMP_OFFSET_REG_CLR);
+	mxs_lradc_reg_clear(lradc, LRADC_DELAY_TRIGGER_LRADCS_MASK |
+					LRADC_DELAY_KICK, LRADC_DELAY(0));
 
-	writel(0xff, lradc->base + LRADC_CTRL0 + STMP_OFFSET_REG_CLR);
-	writel(LRADC_CTRL1_MX28_LRADC_IRQ_EN_MASK,
-		lradc->base + LRADC_CTRL1 + STMP_OFFSET_REG_CLR);
+	mxs_lradc_reg_clear(lradc, 0xff, LRADC_CTRL0);
+	mxs_lradc_reg_clear(lradc, LRADC_CTRL1_MX28_LRADC_IRQ_EN_MASK,
+					LRADC_CTRL1);
 
 	kfree(lradc->buffer);
 	mutex_unlock(&lradc->lock);
@@ -867,24 +904,24 @@ static int mxs_lradc_hw_init(struct mxs_lradc *lradc)
 		return ret;
 
 	/* Configure DELAY CHANNEL 0 for generic ADC sampling. */
-	writel(adc_cfg, lradc->base + LRADC_DELAY(0));
+	mxs_lradc_reg_wrt(lradc, adc_cfg, LRADC_DELAY(0));
 
 	/* Disable remaining DELAY CHANNELs */
-	writel(0, lradc->base + LRADC_DELAY(1));
-	writel(0, lradc->base + LRADC_DELAY(2));
-	writel(0, lradc->base + LRADC_DELAY(3));
+	mxs_lradc_reg_wrt(lradc, 0, LRADC_DELAY(1));
+	mxs_lradc_reg_wrt(lradc, 0, LRADC_DELAY(2));
+	mxs_lradc_reg_wrt(lradc, 0, LRADC_DELAY(3));
 
 	/* Configure the touchscreen type */
-	writel(LRADC_CTRL0_MX28_TOUCH_SCREEN_TYPE,
-		lradc->base + LRADC_CTRL0 + STMP_OFFSET_REG_CLR);
+	mxs_lradc_reg_clear(lradc, LRADC_CTRL0_MX28_TOUCH_SCREEN_TYPE,
+							LRADC_CTRL0);
 
-	if (lradc->use_touchscreen == MXS_LRADC_TOUCHSCREEN_5WIRE) {
-		writel(LRADC_CTRL0_MX28_TOUCH_SCREEN_TYPE,
-			lradc->base + LRADC_CTRL0 + STMP_OFFSET_REG_SET);
+	if (lradc->use_touchscreen == MXS_LRADC_TOUCHSCREEN_5WIRE)
+		mxs_lradc_reg_set(lradc, LRADC_CTRL0_MX28_TOUCH_SCREEN_TYPE,
+				LRADC_CTRL0);
 	}
 
 	/* Start internal temperature sensing. */
-	writel(0, lradc->base + LRADC_CTRL2);
+	mxs_lradc_reg_wrt(lradc, 0, LRADC_CTRL2);
 
 	return 0;
 }
@@ -893,11 +930,10 @@ static void mxs_lradc_hw_stop(struct mxs_lradc *lradc)
 {
 	int i;
 
-	writel(LRADC_CTRL1_MX28_LRADC_IRQ_EN_MASK,
-		lradc->base + LRADC_CTRL1 + STMP_OFFSET_REG_CLR);
+	mxs_lradc_reg_clear(lradc, mxs_lradc_irq_en_mask(lradc), LRADC_CTRL1);
 
 	for (i = 0; i < LRADC_MAX_DELAY_CHANS; i++)
-		writel(0, lradc->base + LRADC_DELAY(i));
+		mxs_lradc_reg_wrt(lradc, 0, LRADC_DELAY(i));
 }
 
 static const struct of_device_id mxs_lradc_dt_ids[] = {
#14 lore raw

PATCH 5/9 Staging/iio/adc/touchscreen/MXS: add i.MX23 support to the LRADC touchscreen driver

In reply to Juergen Beisert

Distinguish i.MX23 and i.MX28 at runtime and do the same for both SoC at least for the 4 wire touchscreen.

Note: support for the remaining LRADC channels is not tested on an i.MX23 yet.

CC linux-arm-kernel at lists.infradead.org
CC linux-input at vger.kernel.org
CC devel at driverdev.osuosl.org
CC Marek Vasut <[email protected]>
CC Fabio Estevam <[email protected]>
CC Jonathan Cameron <[email protected]>
---
 drivers/staging/iio/adc/mxs-lradc.c | 66 ++++++++++++++++++++++++++++++-------
 1 file changed, 55 insertions(+), 11 deletions(-)
drivers/staging/iio/adc/mxs-lradc.c +55 -11
index dd47ec2..a92e810 100644
@@ -191,20 +191,33 @@ struct mxs_lradc {
 # define LRADC_CTRL0_MX28_XNPSW	/* XM */	(1 << 17)
 # define LRADC_CTRL0_MX28_XPPSW	/* XP */	(1 << 16)
 
+# define LRADC_CTRL0_MX23_TOUCH_DETECT_ENABLE	(1 << 20)
+# define LRADC_CTRL0_MX23_YM			(1 << 19)
+# define LRADC_CTRL0_MX23_XM			(1 << 18)
+# define LRADC_CTRL0_MX23_YP			(1 << 17)
+# define LRADC_CTRL0_MX23_XP			(1 << 16)
+
 # define LRADC_CTRL0_MX28_PLATE_MASK \
 		(LRADC_CTRL0_MX28_TOUCH_DETECT_ENABLE | \
 		LRADC_CTRL0_MX28_YNNSW | LRADC_CTRL0_MX28_YPNSW | \
 		LRADC_CTRL0_MX28_YPPSW | LRADC_CTRL0_MX28_XNNSW | \
 		LRADC_CTRL0_MX28_XNPSW | LRADC_CTRL0_MX28_XPPSW)
 
+# define LRADC_CTRL0_MX23_PLATE_MASK \
+		(LRADC_CTRL0_MX23_TOUCH_DETECT_ENABLE | \
+		LRADC_CTRL0_MX23_YM | LRADC_CTRL0_MX23_XM | \
+		LRADC_CTRL0_MX23_YP | LRADC_CTRL0_MX23_XP)
+
 #define	LRADC_CTRL1				0x10
 #define	LRADC_CTRL1_TOUCH_DETECT_IRQ_EN		(1 << 24)
 #define	LRADC_CTRL1_LRADC_IRQ_EN(n)		(1 << ((n) + 16))
 #define	LRADC_CTRL1_MX28_LRADC_IRQ_EN_MASK	(0x1fff << 16)
+#define	LRADC_CTRL1_MX23_LRADC_IRQ_EN_MASK	(0x01ff << 16)
 #define	LRADC_CTRL1_LRADC_IRQ_EN_OFFSET		16
 #define	LRADC_CTRL1_TOUCH_DETECT_IRQ		(1 << 8)
 #define	LRADC_CTRL1_LRADC_IRQ(n)		(1 << (n))
 #define	LRADC_CTRL1_MX28_LRADC_IRQ_MASK		0x1fff
+#define	LRADC_CTRL1_MX23_LRADC_IRQ_MASK		0x01ff
 #define	LRADC_CTRL1_LRADC_IRQ_OFFSET		0
 
 #define	LRADC_CTRL2				0x20
@@ -255,37 +268,58 @@ static void mxs_lradc_reg_wrt(struct mxs_lradc *lradc, u32 val, u32 reg)
 
 static u32 mxs_lradc_plate_mask(struct mxs_lradc *lradc)
 {
-	return LRADC_CTRL0_MX28_PLATE_MASK;
+	if (lradc->soc == IMX23_LRADC)
+		return LRADC_CTRL0_MX23_PLATE_MASK;
+	else
+		return LRADC_CTRL0_MX28_PLATE_MASK;
 }
 
 static u32 mxs_lradc_irq_en_mask(struct mxs_lradc *lradc)
 {
-	return LRADC_CTRL1_MX28_LRADC_IRQ_EN_MASK;
+	if (lradc->soc == IMX23_LRADC)
+		return LRADC_CTRL1_MX23_LRADC_IRQ_EN_MASK;
+	else
+		return LRADC_CTRL1_MX28_LRADC_IRQ_EN_MASK;
 }
 
 static u32 mxs_lradc_irq_mask(struct mxs_lradc *lradc)
 {
-	return LRADC_CTRL1_MX28_LRADC_IRQ_MASK;
+	if (lradc->soc == IMX23_LRADC)
+		return LRADC_CTRL1_MX23_LRADC_IRQ_MASK;
+	else
+		return LRADC_CTRL1_MX28_LRADC_IRQ_MASK;
 }
 
 static u32 mxs_lradc_touch_detect_bit(struct mxs_lradc *lradc)
 {
-	return LRADC_CTRL0_MX28_TOUCH_DETECT_ENABLE;
+	if (lradc->soc == IMX23_LRADC)
+		return LRADC_CTRL0_MX23_TOUCH_DETECT_ENABLE;
+	else
+		return LRADC_CTRL0_MX28_TOUCH_DETECT_ENABLE;
 }
 
 static u32 mxs_lradc_drive_x_plate(struct mxs_lradc *lradc)
 {
-	return LRADC_CTRL0_MX28_XPPSW | LRADC_CTRL0_MX28_XNNSW;
+	if (lradc->soc == IMX23_LRADC)
+		return LRADC_CTRL0_MX23_XP | LRADC_CTRL0_MX23_XM;
+	else
+		return LRADC_CTRL0_MX28_XPPSW | LRADC_CTRL0_MX28_XNNSW;
 }
 
 static u32 mxs_lradc_drive_y_plate(struct mxs_lradc *lradc)
 {
-	return LRADC_CTRL0_MX28_YPPSW | LRADC_CTRL0_MX28_YNNSW;
+	if (lradc->soc == IMX23_LRADC)
+		return LRADC_CTRL0_MX23_YP | LRADC_CTRL0_MX23_YM;
+	else
+		return LRADC_CTRL0_MX28_YPPSW | LRADC_CTRL0_MX28_YNNSW;
 }
 
 static u32 mxs_lradc_drive_pressure(struct mxs_lradc *lradc)
 {
-	return LRADC_CTRL0_MX28_YPPSW | LRADC_CTRL0_MX28_XNNSW;
+	if (lradc->soc == IMX23_LRADC)
+		return LRADC_CTRL0_MX23_YP | LRADC_CTRL0_MX23_XM;
+	else
+		return LRADC_CTRL0_MX28_YPPSW | LRADC_CTRL0_MX28_XNNSW;
 }
 
 /*
@@ -322,7 +356,8 @@ static int mxs_lradc_read_raw(struct iio_dev *iio_dev,
 	 * Virtual channel 0 is always used here as the others are always not
 	 * used if doing raw sampling.
 	 */
-	mxs_lradc_reg_clear(lradc, LRADC_CTRL1_MX28_LRADC_IRQ_EN_MASK,
+	if (lradc->soc == IMX28_LRADC)
+		mxs_lradc_reg_clear(lradc, LRADC_CTRL1_MX28_LRADC_IRQ_EN_MASK,
 			LRADC_CTRL1);
 	mxs_lradc_reg_clear(lradc, 0xff, LRADC_CTRL0);
 
@@ -770,7 +805,8 @@ static int mxs_lradc_buffer_preenable(struct iio_dev *iio)
 	if (ret < 0)
 		goto err_buf;
 
-	mxs_lradc_reg_clear(lradc, LRADC_CTRL1_MX28_LRADC_IRQ_EN_MASK,
+	if (lradc->soc == IMX28_LRADC)
+		mxs_lradc_reg_clear(lradc, LRADC_CTRL1_MX28_LRADC_IRQ_EN_MASK,
 							LRADC_CTRL1);
 	mxs_lradc_reg_clear(lradc, 0xff, LRADC_CTRL0);
 
@@ -808,7 +844,8 @@ static int mxs_lradc_buffer_postdisable(struct iio_dev *iio)
 					LRADC_DELAY_KICK, LRADC_DELAY(0));
 
 	mxs_lradc_reg_clear(lradc, 0xff, LRADC_CTRL0);
-	mxs_lradc_reg_clear(lradc, LRADC_CTRL1_MX28_LRADC_IRQ_EN_MASK,
+	if (lradc->soc == IMX28_LRADC)
+		mxs_lradc_reg_clear(lradc, LRADC_CTRL1_MX28_LRADC_IRQ_EN_MASK,
 					LRADC_CTRL1);
 
 	kfree(lradc->buffer);
@@ -912,7 +949,8 @@ static int mxs_lradc_hw_init(struct mxs_lradc *lradc)
 	mxs_lradc_reg_wrt(lradc, 0, LRADC_DELAY(3));
 
 	/* Configure the touchscreen type */
-	mxs_lradc_reg_clear(lradc, LRADC_CTRL0_MX28_TOUCH_SCREEN_TYPE,
+	if (lradc->soc == IMX28_LRADC) {
+		mxs_lradc_reg_clear(lradc, LRADC_CTRL0_MX28_TOUCH_SCREEN_TYPE,
 							LRADC_CTRL0);
 
 	if (lradc->use_touchscreen == MXS_LRADC_TOUCHSCREEN_5WIRE)
@@ -993,6 +1031,12 @@ static int mxs_lradc_probe(struct platform_device *pdev)
 		dev_warn(dev, "Unsupported number of touchscreen wires (%d)\n",
 				ts_wires);
 
+	if ((lradc->soc == IMX23_LRADC) && (ts_wires == 5)) {
+		dev_warn(dev, "No support for 5 wire touches on i.MX23\n");
+		dev_warn(dev, "Falling back to 4 wire\n");
+		ts_wires = 4;
+	}
+
 	/* Grab all IRQ sources */
 	for (i = 0; i < of_cfg->irq_count; i++) {
 		lradc->irq[i] = platform_get_irq(pdev, i);
Signature · 1 line
1.8.4.rc3
maintainer Applied
#15 lore raw

PATCH 5/9 Staging/iio/adc/touchscreen/MXS: add i.MX23 support to the LRADC touchscreen driver

Quoted 6 lines · Juergen Beisert

Distinguish i.MX23 and i.MX28 at runtime and do the same for both SoC at least for the 4 wire touchscreen.

Note: support for the remaining LRADC channels is not tested on an i.MX23 yet.

Quoted 7 lines

Applied to the togreg branch of iio.git

Thanks,

Quoted 162 lines
---
 drivers/staging/iio/adc/mxs-lradc.c | 66 ++++++++++++++++++++++++++++++-------
 1 file changed, 55 insertions(+), 11 deletions(-)
drivers/staging/iio/adc/mxs-lradc.c +55 -11
index dd47ec2..a92e810 100644
@@ -191,20 +191,33 @@ struct mxs_lradc {
 # define LRADC_CTRL0_MX28_XNPSW	/* XM */	(1 << 17)
 # define LRADC_CTRL0_MX28_XPPSW	/* XP */	(1 << 16)
 
+# define LRADC_CTRL0_MX23_TOUCH_DETECT_ENABLE	(1 << 20)
+# define LRADC_CTRL0_MX23_YM			(1 << 19)
+# define LRADC_CTRL0_MX23_XM			(1 << 18)
+# define LRADC_CTRL0_MX23_YP			(1 << 17)
+# define LRADC_CTRL0_MX23_XP			(1 << 16)
+
 # define LRADC_CTRL0_MX28_PLATE_MASK \
 		(LRADC_CTRL0_MX28_TOUCH_DETECT_ENABLE | \
 		LRADC_CTRL0_MX28_YNNSW | LRADC_CTRL0_MX28_YPNSW | \
 		LRADC_CTRL0_MX28_YPPSW | LRADC_CTRL0_MX28_XNNSW | \
 		LRADC_CTRL0_MX28_XNPSW | LRADC_CTRL0_MX28_XPPSW)
 
+# define LRADC_CTRL0_MX23_PLATE_MASK \
+		(LRADC_CTRL0_MX23_TOUCH_DETECT_ENABLE | \
+		LRADC_CTRL0_MX23_YM | LRADC_CTRL0_MX23_XM | \
+		LRADC_CTRL0_MX23_YP | LRADC_CTRL0_MX23_XP)
+
 #define	LRADC_CTRL1				0x10
 #define	LRADC_CTRL1_TOUCH_DETECT_IRQ_EN		(1 << 24)
 #define	LRADC_CTRL1_LRADC_IRQ_EN(n)		(1 << ((n) + 16))
 #define	LRADC_CTRL1_MX28_LRADC_IRQ_EN_MASK	(0x1fff << 16)
+#define	LRADC_CTRL1_MX23_LRADC_IRQ_EN_MASK	(0x01ff << 16)
 #define	LRADC_CTRL1_LRADC_IRQ_EN_OFFSET		16
 #define	LRADC_CTRL1_TOUCH_DETECT_IRQ		(1 << 8)
 #define	LRADC_CTRL1_LRADC_IRQ(n)		(1 << (n))
 #define	LRADC_CTRL1_MX28_LRADC_IRQ_MASK		0x1fff
+#define	LRADC_CTRL1_MX23_LRADC_IRQ_MASK		0x01ff
 #define	LRADC_CTRL1_LRADC_IRQ_OFFSET		0
 
 #define	LRADC_CTRL2				0x20
@@ -255,37 +268,58 @@ static void mxs_lradc_reg_wrt(struct mxs_lradc *lradc, u32 val, u32 reg)
 
 static u32 mxs_lradc_plate_mask(struct mxs_lradc *lradc)
 {
-	return LRADC_CTRL0_MX28_PLATE_MASK;
+	if (lradc->soc == IMX23_LRADC)
+		return LRADC_CTRL0_MX23_PLATE_MASK;
+	else
+		return LRADC_CTRL0_MX28_PLATE_MASK;
 }
 
 static u32 mxs_lradc_irq_en_mask(struct mxs_lradc *lradc)
 {
-	return LRADC_CTRL1_MX28_LRADC_IRQ_EN_MASK;
+	if (lradc->soc == IMX23_LRADC)
+		return LRADC_CTRL1_MX23_LRADC_IRQ_EN_MASK;
+	else
+		return LRADC_CTRL1_MX28_LRADC_IRQ_EN_MASK;
 }
 
 static u32 mxs_lradc_irq_mask(struct mxs_lradc *lradc)
 {
-	return LRADC_CTRL1_MX28_LRADC_IRQ_MASK;
+	if (lradc->soc == IMX23_LRADC)
+		return LRADC_CTRL1_MX23_LRADC_IRQ_MASK;
+	else
+		return LRADC_CTRL1_MX28_LRADC_IRQ_MASK;
 }
 
 static u32 mxs_lradc_touch_detect_bit(struct mxs_lradc *lradc)
 {
-	return LRADC_CTRL0_MX28_TOUCH_DETECT_ENABLE;
+	if (lradc->soc == IMX23_LRADC)
+		return LRADC_CTRL0_MX23_TOUCH_DETECT_ENABLE;
+	else
+		return LRADC_CTRL0_MX28_TOUCH_DETECT_ENABLE;
 }
 
 static u32 mxs_lradc_drive_x_plate(struct mxs_lradc *lradc)
 {
-	return LRADC_CTRL0_MX28_XPPSW | LRADC_CTRL0_MX28_XNNSW;
+	if (lradc->soc == IMX23_LRADC)
+		return LRADC_CTRL0_MX23_XP | LRADC_CTRL0_MX23_XM;
+	else
+		return LRADC_CTRL0_MX28_XPPSW | LRADC_CTRL0_MX28_XNNSW;
 }
 
 static u32 mxs_lradc_drive_y_plate(struct mxs_lradc *lradc)
 {
-	return LRADC_CTRL0_MX28_YPPSW | LRADC_CTRL0_MX28_YNNSW;
+	if (lradc->soc == IMX23_LRADC)
+		return LRADC_CTRL0_MX23_YP | LRADC_CTRL0_MX23_YM;
+	else
+		return LRADC_CTRL0_MX28_YPPSW | LRADC_CTRL0_MX28_YNNSW;
 }
 
 static u32 mxs_lradc_drive_pressure(struct mxs_lradc *lradc)
 {
-	return LRADC_CTRL0_MX28_YPPSW | LRADC_CTRL0_MX28_XNNSW;
+	if (lradc->soc == IMX23_LRADC)
+		return LRADC_CTRL0_MX23_YP | LRADC_CTRL0_MX23_XM;
+	else
+		return LRADC_CTRL0_MX28_YPPSW | LRADC_CTRL0_MX28_XNNSW;
 }
 
 /*
@@ -322,7 +356,8 @@ static int mxs_lradc_read_raw(struct iio_dev *iio_dev,
 	 * Virtual channel 0 is always used here as the others are always not
 	 * used if doing raw sampling.
 	 */
-	mxs_lradc_reg_clear(lradc, LRADC_CTRL1_MX28_LRADC_IRQ_EN_MASK,
+	if (lradc->soc == IMX28_LRADC)
+		mxs_lradc_reg_clear(lradc, LRADC_CTRL1_MX28_LRADC_IRQ_EN_MASK,
 			LRADC_CTRL1);
 	mxs_lradc_reg_clear(lradc, 0xff, LRADC_CTRL0);
 
@@ -770,7 +805,8 @@ static int mxs_lradc_buffer_preenable(struct iio_dev *iio)
 	if (ret < 0)
 		goto err_buf;
 
-	mxs_lradc_reg_clear(lradc, LRADC_CTRL1_MX28_LRADC_IRQ_EN_MASK,
+	if (lradc->soc == IMX28_LRADC)
+		mxs_lradc_reg_clear(lradc, LRADC_CTRL1_MX28_LRADC_IRQ_EN_MASK,
 							LRADC_CTRL1);
 	mxs_lradc_reg_clear(lradc, 0xff, LRADC_CTRL0);
 
@@ -808,7 +844,8 @@ static int mxs_lradc_buffer_postdisable(struct iio_dev *iio)
 					LRADC_DELAY_KICK, LRADC_DELAY(0));
 
 	mxs_lradc_reg_clear(lradc, 0xff, LRADC_CTRL0);
-	mxs_lradc_reg_clear(lradc, LRADC_CTRL1_MX28_LRADC_IRQ_EN_MASK,
+	if (lradc->soc == IMX28_LRADC)
+		mxs_lradc_reg_clear(lradc, LRADC_CTRL1_MX28_LRADC_IRQ_EN_MASK,
 					LRADC_CTRL1);
 
 	kfree(lradc->buffer);
@@ -912,7 +949,8 @@ static int mxs_lradc_hw_init(struct mxs_lradc *lradc)
 	mxs_lradc_reg_wrt(lradc, 0, LRADC_DELAY(3));
 
 	/* Configure the touchscreen type */
-	mxs_lradc_reg_clear(lradc, LRADC_CTRL0_MX28_TOUCH_SCREEN_TYPE,
+	if (lradc->soc == IMX28_LRADC) {
+		mxs_lradc_reg_clear(lradc, LRADC_CTRL0_MX28_TOUCH_SCREEN_TYPE,
 							LRADC_CTRL0);
 
 	if (lradc->use_touchscreen == MXS_LRADC_TOUCHSCREEN_5WIRE)
@@ -993,6 +1031,12 @@ static int mxs_lradc_probe(struct platform_device *pdev)
 		dev_warn(dev, "Unsupported number of touchscreen wires (%d)\n",
 				ts_wires);
 
+	if ((lradc->soc == IMX23_LRADC) && (ts_wires == 5)) {
+		dev_warn(dev, "No support for 5 wire touches on i.MX23\n");
+		dev_warn(dev, "Falling back to 4 wire\n");
+		ts_wires = 4;
+	}
+
 	/* Grab all IRQ sources */
 	for (i = 0; i < of_cfg->irq_count; i++) {
 		lradc->irq[i] = platform_get_irq(pdev, i);
#16 lore raw

PATCH 6/9 Staging/iio/adc/touchscreen/MXS: add interrupt driven touch detection

In reply to Juergen Beisert

For battery driven systems it is a very bad idea to collect the touchscreen data within a kernel busy loop.

This change uses the features of the hardware to delay and accumulate samples in hardware to avoid a high interrupt and CPU load.

Note: this is only tested on an i.MX23 SoC yet.

CC linux-arm-kernel at lists.infradead.org
CC linux-input at vger.kernel.org
CC devel at driverdev.osuosl.org
CC Marek Vasut <[email protected]>
CC Fabio Estevam <[email protected]>
CC Jonathan Cameron <[email protected]>
CC Dmitry Torokhov <[email protected]>
CC linux-input at vger.kernel.org
---
 drivers/staging/iio/adc/mxs-lradc.c | 530 ++++++++++++++++++++++++++++++++----
 1 file changed, 476 insertions(+), 54 deletions(-)
drivers/staging/iio/adc/mxs-lradc.c +476 -54
index a92e810..76a900d 100644
@@ -130,6 +130,17 @@ enum mxs_lradc_ts {
 	MXS_LRADC_TOUCHSCREEN_5WIRE,
 };
 
+/*
+ * Touchscreen handling
+ */
+enum lradc_ts_plate {
+	LRADC_TOUCH = 0,
+	LRADC_SAMPLE_X,
+	LRADC_SAMPLE_Y,
+	LRADC_SAMPLE_PRESSURE,
+	LRADC_SAMPLE_VALID,
+};
+
 struct mxs_lradc {
 	struct device		*dev;
 	void __iomem		*base;
@@ -172,13 +183,25 @@ struct mxs_lradc {
 #define CHAN_MASK_TOUCHSCREEN_4WIRE	(0xf << 2)
 #define CHAN_MASK_TOUCHSCREEN_5WIRE	(0x1f << 2)
 	enum mxs_lradc_ts	use_touchscreen;
-	bool			stop_touchscreen;
 	bool			use_touchbutton;
 
 	struct input_dev	*ts_input;
 	struct work_struct	ts_work;
 
 	enum mxs_lradc_id	soc;
+	enum lradc_ts_plate	cur_plate; /* statemachine */
+	bool			ts_valid;
+	unsigned		ts_x_pos;
+	unsigned		ts_y_pos;
+	unsigned		ts_pressure;
+
+	/* handle touchscreen's physical behaviour */
+	/* samples per coordinate */
+	unsigned		over_sample_cnt;
+	/* time clocks between samples */
+	unsigned		over_sample_delay;
+	/* time in clocks to wait after the plates where switched */
+	unsigned		settling_delay;
 };
 
 #define	LRADC_CTRL0				0x00
@@ -230,19 +253,33 @@ struct mxs_lradc {
 #define	LRADC_CH_ACCUMULATE			(1 << 29)
 #define	LRADC_CH_NUM_SAMPLES_MASK		(0x1f << 24)
 #define	LRADC_CH_NUM_SAMPLES_OFFSET		24
+#define	LRADC_CH_NUM_SAMPLES(x) \
+				((x) << LRADC_CH_NUM_SAMPLES_OFFSET)
 #define	LRADC_CH_VALUE_MASK			0x3ffff
 #define	LRADC_CH_VALUE_OFFSET			0
 
 #define	LRADC_DELAY(n)				(0xd0 + (0x10 * (n)))
 #define	LRADC_DELAY_TRIGGER_LRADCS_MASK		(0xff << 24)
 #define	LRADC_DELAY_TRIGGER_LRADCS_OFFSET	24
+#define	LRADC_DELAY_TRIGGER(x) \
+				(((x) << LRADC_DELAY_TRIGGER_LRADCS_OFFSET) & \
+				LRADC_DELAY_TRIGGER_LRADCS_MASK)
 #define	LRADC_DELAY_KICK			(1 << 20)
 #define	LRADC_DELAY_TRIGGER_DELAYS_MASK		(0xf << 16)
 #define	LRADC_DELAY_TRIGGER_DELAYS_OFFSET	16
+#define	LRADC_DELAY_TRIGGER_DELAYS(x) \
+				(((x) << LRADC_DELAY_TRIGGER_DELAYS_OFFSET) & \
+				LRADC_DELAY_TRIGGER_DELAYS_MASK)
 #define	LRADC_DELAY_LOOP_COUNT_MASK		(0x1f << 11)
 #define	LRADC_DELAY_LOOP_COUNT_OFFSET		11
+#define	LRADC_DELAY_LOOP(x) \
+				(((x) << LRADC_DELAY_LOOP_COUNT_OFFSET) & \
+				LRADC_DELAY_LOOP_COUNT_MASK)
 #define	LRADC_DELAY_DELAY_MASK			0x7ff
 #define	LRADC_DELAY_DELAY_OFFSET		0
+#define	LRADC_DELAY_DELAY(x) \
+				(((x) << LRADC_DELAY_DELAY_OFFSET) & \
+				LRADC_DELAY_DELAY_MASK)
 
 #define	LRADC_CTRL4				0x140
 #define	LRADC_CTRL4_LRADCSELECT_MASK(n)		(0xf << ((n) * 4))
@@ -322,6 +359,404 @@ static u32 mxs_lradc_drive_pressure(struct mxs_lradc *lradc)
 		return LRADC_CTRL0_MX28_YPPSW | LRADC_CTRL0_MX28_XNNSW;
 }
 
+static bool mxs_lradc_check_touch_event(struct mxs_lradc *lradc)
+{
+	return !!(readl(lradc->base + LRADC_STATUS) &
+					LRADC_STATUS_TOUCH_DETECT_RAW);
+}
+
+static void mxs_lradc_setup_ts_channel(struct mxs_lradc *lradc, unsigned ch)
+{
+	/*
+	 * prepare for oversampling conversion
+	 *
+	 * from the datasheet:
+	 * "The ACCUMULATE bit in the appropriate channel register
+	 * HW_LRADC_CHn must be set to 1 if NUM_SAMPLES is greater then 0;
+	 * otherwise, the IRQs will not fire."
+	 */
+	mxs_lradc_reg_wrt(lradc, LRADC_CH_ACCUMULATE |
+			LRADC_CH_NUM_SAMPLES(lradc->over_sample_cnt - 1),
+			LRADC_CH(ch));
+
+	/* from the datasheet:
+	 * "Software must clear this register in preparation for a
+	 * multi-cycle accumulation.
+	 */
+	mxs_lradc_reg_clear(lradc, LRADC_CH_VALUE_MASK, LRADC_CH(ch));
+
+	/* prepare the delay/loop unit according to the oversampling count */
+	mxs_lradc_reg_wrt(lradc, LRADC_DELAY_TRIGGER(1 << ch) |
+		LRADC_DELAY_TRIGGER_DELAYS(0) |
+		LRADC_DELAY_LOOP(lradc->over_sample_cnt - 1) |
+		LRADC_DELAY_DELAY(lradc->over_sample_delay - 1),
+			LRADC_DELAY(3));
+
+	mxs_lradc_reg_clear(lradc, LRADC_CTRL1_LRADC_IRQ(2) |
+			LRADC_CTRL1_LRADC_IRQ(3) | LRADC_CTRL1_LRADC_IRQ(4) |
+			LRADC_CTRL1_LRADC_IRQ(5), LRADC_CTRL1);
+
+	/* wake us again, when the complete conversion is done */
+	mxs_lradc_reg_set(lradc, LRADC_CTRL1_LRADC_IRQ_EN(ch), LRADC_CTRL1);
+	/*
+	 * after changing the touchscreen plates setting
+	 * the signals need some initial time to settle. Start the
+	 * SoC's delay unit and start the conversion later
+	 * and automatically.
+	 */
+	mxs_lradc_reg_wrt(lradc, LRADC_DELAY_TRIGGER(0) | /* don't trigger ADC */
+		LRADC_DELAY_TRIGGER_DELAYS(1 << 3) | /* trigger DELAY unit#3 */
+		LRADC_DELAY_KICK |
+		LRADC_DELAY_DELAY(lradc->settling_delay),
+			LRADC_DELAY(2));
+}
+
+/*
+ * Pressure detection is special:
+ * We want to do both required measurements for the pressure detection in
+ * one turn. Use the hardware features to chain both conversions and let the
+ * hardware report one interrupt if both conversions are done
+ */
+static void mxs_lradc_setup_ts_pressure(struct mxs_lradc *lradc, unsigned ch1,
+							unsigned ch2)
+{
+	u32 reg;
+
+	/*
+	 * prepare for oversampling conversion
+	 *
+	 * from the datasheet:
+	 * "The ACCUMULATE bit in the appropriate channel register
+	 * HW_LRADC_CHn must be set to 1 if NUM_SAMPLES is greater then 0;
+	 * otherwise, the IRQs will not fire."
+	 */
+	reg = LRADC_CH_ACCUMULATE |
+		LRADC_CH_NUM_SAMPLES(lradc->over_sample_cnt - 1);
+	mxs_lradc_reg_wrt(lradc, reg, LRADC_CH(ch1));
+	mxs_lradc_reg_wrt(lradc, reg, LRADC_CH(ch2));
+
+	/* from the datasheet:
+	 * "Software must clear this register in preparation for a
+	 * multi-cycle accumulation.
+	 */
+	mxs_lradc_reg_clear(lradc, LRADC_CH_VALUE_MASK, LRADC_CH(ch1));
+	mxs_lradc_reg_clear(lradc, LRADC_CH_VALUE_MASK, LRADC_CH(ch2));
+
+	/* prepare the delay/loop unit according to the oversampling count */
+	mxs_lradc_reg_wrt(lradc, LRADC_DELAY_TRIGGER(1 << ch1) |
+		LRADC_DELAY_TRIGGER(1 << ch2) | /* start both channels */
+		LRADC_DELAY_TRIGGER_DELAYS(0) |
+		LRADC_DELAY_LOOP(lradc->over_sample_cnt - 1) |
+		LRADC_DELAY_DELAY(lradc->over_sample_delay - 1),
+					LRADC_DELAY(3));
+
+	mxs_lradc_reg_clear(lradc, LRADC_CTRL1_LRADC_IRQ(2) |
+			LRADC_CTRL1_LRADC_IRQ(3) | LRADC_CTRL1_LRADC_IRQ(4) |
+			LRADC_CTRL1_LRADC_IRQ(5), LRADC_CTRL1);
+
+	/* wake us again, when the conversions are done */
+	mxs_lradc_reg_set(lradc, LRADC_CTRL1_LRADC_IRQ_EN(ch2), LRADC_CTRL1);
+	/*
+	 * after changing the touchscreen plates setting
+	 * the signals need some initial time to settle. Start the
+	 * SoC's delay unit and start the conversion later
+	 * and automatically.
+	 */
+	mxs_lradc_reg_wrt(lradc, LRADC_DELAY_TRIGGER(0) | /* don't trigger ADC */
+		LRADC_DELAY_TRIGGER_DELAYS(1 << 3) | /* trigger DELAY unit#3 */
+		LRADC_DELAY_KICK |
+		LRADC_DELAY_DELAY(lradc->settling_delay), LRADC_DELAY(2));
+}
+
+static unsigned mxs_lradc_read_raw_channel(struct mxs_lradc *lradc,
+							unsigned channel)
+{
+	u32 reg;
+	unsigned num_samples, val;
+
+	reg = readl(lradc->base + LRADC_CH(channel));
+	if (reg & LRADC_CH_ACCUMULATE)
+		num_samples = lradc->over_sample_cnt;
+	else
+		num_samples = 1;
+
+	val = (reg & LRADC_CH_VALUE_MASK) >> LRADC_CH_VALUE_OFFSET;
+	return val / num_samples;
+}
+
+static unsigned mxs_lradc_read_ts_pressure(struct mxs_lradc *lradc,
+						unsigned ch1, unsigned ch2)
+{
+	u32 reg, mask;
+	unsigned pressure, m1, m2;
+
+	mask = LRADC_CTRL1_LRADC_IRQ(ch1) | LRADC_CTRL1_LRADC_IRQ(ch2);
+	reg = readl(lradc->base + LRADC_CTRL1) & mask;
+
+	while (reg != mask) {
+		reg = readl(lradc->base + LRADC_CTRL1) & mask;
+		dev_dbg(lradc->dev, "One channel is still busy: %X\n", reg);
+	}
+
+	m1 = mxs_lradc_read_raw_channel(lradc, ch1);
+	m2 = mxs_lradc_read_raw_channel(lradc, ch2);
+
+	if (m2 == 0) {
+		dev_warn(lradc->dev, "Cannot calculate pressure\n");
+		return 1 << (LRADC_RESOLUTION - 1);
+	}
+
+	/* simply scale the value from 0 ... max ADC resolution */
+	pressure = m1;
+	pressure *= (1 << LRADC_RESOLUTION);
+	pressure /= m2;
+
+	dev_dbg(lradc->dev, "Pressure = %u\n", pressure);
+	return pressure;
+}
+
+#define TS_CH_XP 2
+#define TS_CH_YP 3
+#define TS_CH_XM 4
+#define TS_CH_YM 5
+
+static int mxs_lradc_read_ts_channel(struct mxs_lradc *lradc)
+{
+	u32 reg;
+	int val;
+
+	reg = readl(lradc->base + LRADC_CTRL1);
+
+	/* only channels 3 to 5 are of interest here */
+	if (reg & LRADC_CTRL1_LRADC_IRQ(TS_CH_YP)) {
+		mxs_lradc_reg_clear(lradc, LRADC_CTRL1_LRADC_IRQ_EN(TS_CH_YP) |
+			LRADC_CTRL1_LRADC_IRQ(TS_CH_YP), LRADC_CTRL1);
+		val = mxs_lradc_read_raw_channel(lradc, TS_CH_YP);
+	} else if (reg & LRADC_CTRL1_LRADC_IRQ(TS_CH_XM)) {
+		mxs_lradc_reg_clear(lradc, LRADC_CTRL1_LRADC_IRQ_EN(TS_CH_XM) |
+			LRADC_CTRL1_LRADC_IRQ(TS_CH_XM), LRADC_CTRL1);
+		val = mxs_lradc_read_raw_channel(lradc, TS_CH_XM);
+	} else if (reg & LRADC_CTRL1_LRADC_IRQ(TS_CH_YM)) {
+		mxs_lradc_reg_clear(lradc, LRADC_CTRL1_LRADC_IRQ_EN(TS_CH_YM) |
+			LRADC_CTRL1_LRADC_IRQ(TS_CH_YM), LRADC_CTRL1);
+		val = mxs_lradc_read_raw_channel(lradc, TS_CH_YM);
+	} else {
+		return -EIO;
+	}
+
+	mxs_lradc_reg_wrt(lradc, 0, LRADC_DELAY(2));
+	mxs_lradc_reg_wrt(lradc, 0, LRADC_DELAY(3));
+
+	return val;
+}
+
+/*
+ * YP(open)--+-------------+
+ *           |             |--+
+ *           |             |  |
+ *    YM(-)--+-------------+  |
+ *             +--------------+
+ *             |              |
+ *         XP(weak+)        XM(open)
+ *
+ * "weak+" means 200k Ohm VDDIO
+ * (-) means GND
+ */
+static void mxs_lradc_setup_touch_detection(struct mxs_lradc *lradc)
+{
+	/*
+	 * In order to detect a touch event the 'touch detect enable' bit
+	 * enables:
+	 *  - a weak pullup to the X+ connector
+	 *  - a strong ground at the Y- connector
+	 */
+	mxs_lradc_reg_clear(lradc, mxs_lradc_plate_mask(lradc), LRADC_CTRL0);
+	mxs_lradc_reg_set(lradc, mxs_lradc_touch_detect_bit(lradc),
+				LRADC_CTRL0);
+}
+
+/*
+ * YP(meas)--+-------------+
+ *           |             |--+
+ *           |             |  |
+ * YM(open)--+-------------+  |
+ *             +--------------+
+ *             |              |
+ *           XP(+)          XM(-)
+ *
+ * (+) means here 1.85 V
+ * (-) means here GND
+ */
+static void mxs_lradc_prepare_x_pos(struct mxs_lradc *lradc)
+{
+	mxs_lradc_reg_clear(lradc, mxs_lradc_plate_mask(lradc), LRADC_CTRL0);
+	mxs_lradc_reg_set(lradc, mxs_lradc_drive_x_plate(lradc), LRADC_CTRL0);
+
+	lradc->cur_plate = LRADC_SAMPLE_X;
+	mxs_lradc_setup_ts_channel(lradc, TS_CH_YP);
+}
+
+/*
+ *   YP(+)--+-------------+
+ *          |             |--+
+ *          |             |  |
+ *   YM(-)--+-------------+  |
+ *            +--------------+
+ *            |              |
+ *         XP(open)        XM(meas)
+ *
+ * (+) means here 1.85 V
+ * (-) means here GND
+ */
+static void mxs_lradc_prepare_y_pos(struct mxs_lradc *lradc)
+{
+	mxs_lradc_reg_clear(lradc, mxs_lradc_plate_mask(lradc), LRADC_CTRL0);
+	mxs_lradc_reg_set(lradc, mxs_lradc_drive_y_plate(lradc), LRADC_CTRL0);
+
+	lradc->cur_plate = LRADC_SAMPLE_Y;
+	mxs_lradc_setup_ts_channel(lradc, TS_CH_XM);
+}
+
+/*
+ *    YP(+)--+-------------+
+ *           |             |--+
+ *           |             |  |
+ * YM(meas)--+-------------+  |
+ *             +--------------+
+ *             |              |
+ *          XP(meas)        XM(-)
+ *
+ * (+) means here 1.85 V
+ * (-) means here GND
+ */
+static void mxs_lradc_prepare_pressure(struct mxs_lradc *lradc)
+{
+	mxs_lradc_reg_clear(lradc, mxs_lradc_plate_mask(lradc), LRADC_CTRL0);
+	mxs_lradc_reg_set(lradc, mxs_lradc_drive_pressure(lradc), LRADC_CTRL0);
+
+	lradc->cur_plate = LRADC_SAMPLE_PRESSURE;
+	mxs_lradc_setup_ts_pressure(lradc, TS_CH_XP, TS_CH_YM);
+}
+
+static void mxs_lradc_enable_touch_detection(struct mxs_lradc *lradc)
+{
+	mxs_lradc_setup_touch_detection(lradc);
+
+	lradc->cur_plate = LRADC_TOUCH;
+	mxs_lradc_reg_clear(lradc, LRADC_CTRL1_TOUCH_DETECT_IRQ |
+				LRADC_CTRL1_TOUCH_DETECT_IRQ_EN, LRADC_CTRL1);
+	mxs_lradc_reg_set(lradc, LRADC_CTRL1_TOUCH_DETECT_IRQ_EN, LRADC_CTRL1);
+}
+
+static void mxs_lradc_report_ts_event(struct mxs_lradc *lradc)
+{
+	input_report_abs(lradc->ts_input, ABS_X, lradc->ts_x_pos);
+	input_report_abs(lradc->ts_input, ABS_Y, lradc->ts_y_pos);
+	input_report_abs(lradc->ts_input, ABS_PRESSURE, lradc->ts_pressure);
+	input_report_key(lradc->ts_input, BTN_TOUCH, 1);
+	input_sync(lradc->ts_input);
+}
+
+static void mxs_lradc_complete_touch_event(struct mxs_lradc *lradc)
+{
+	mxs_lradc_setup_touch_detection(lradc);
+	lradc->cur_plate = LRADC_SAMPLE_VALID;
+	/*
+	 * start a dummy conversion to burn time to settle the signals
+	 * note: we are not interested in the conversion's value
+	 */
+	mxs_lradc_reg_wrt(lradc, 0, LRADC_CH(5));
+	mxs_lradc_reg_clear(lradc, LRADC_CTRL1_LRADC_IRQ(5), LRADC_CTRL1);
+	mxs_lradc_reg_set(lradc, LRADC_CTRL1_LRADC_IRQ_EN(5), LRADC_CTRL1);
+	mxs_lradc_reg_wrt(lradc, LRADC_DELAY_TRIGGER(1 << 5) |
+		LRADC_DELAY_KICK | LRADC_DELAY_DELAY(10), /* waste 5 ms */
+			LRADC_DELAY(2));
+}
+
+/*
+ * in order to avoid false measurements, report only samples where
+ * the surface is still touched after the position measurement
+ */
+static void mxs_lradc_finish_touch_event(struct mxs_lradc *lradc, bool valid)
+{
+	/* if it is still touched, report the sample */
+	if (valid && mxs_lradc_check_touch_event(lradc)) {
+		lradc->ts_valid = true;
+		mxs_lradc_report_ts_event(lradc);
+	}
+
+	/* if it is even still touched, continue with the next measurement */
+	if (mxs_lradc_check_touch_event(lradc)) {
+		mxs_lradc_prepare_y_pos(lradc);
+		return;
+	}
+
+	if (lradc->ts_valid) {
+		/* signal the release */
+		lradc->ts_valid = false;
+		input_report_key(lradc->ts_input, BTN_TOUCH, 0);
+		input_sync(lradc->ts_input);
+	}
+
+	/* if it is released, wait for the next touch via IRQ */
+	mxs_lradc_reg_clear(lradc, LRADC_CTRL1_TOUCH_DETECT_IRQ, LRADC_CTRL1);
+	mxs_lradc_reg_set(lradc, LRADC_CTRL1_TOUCH_DETECT_IRQ_EN, LRADC_CTRL1);
+}
+
+/* touchscreen's state machine */
+static void mxs_lradc_handle_touch(struct mxs_lradc *lradc)
+{
+	int val;
+
+	switch (lradc->cur_plate) {
+	case LRADC_TOUCH:
+		/*
+		 * start with the Y-pos, because it uses nearly the same plate
+		 * settings like the touch detection
+		 */
+		if (mxs_lradc_check_touch_event(lradc)) {
+			mxs_lradc_reg_clear(lradc,
+					LRADC_CTRL1_TOUCH_DETECT_IRQ_EN,
+					LRADC_CTRL1);
+			mxs_lradc_prepare_y_pos(lradc);
+		}
+		mxs_lradc_reg_clear(lradc, LRADC_CTRL1_TOUCH_DETECT_IRQ,
+					LRADC_CTRL1);
+		return;
+
+	case LRADC_SAMPLE_Y:
+		val = mxs_lradc_read_ts_channel(lradc);
+		if (val < 0) {
+			mxs_lradc_enable_touch_detection(lradc); /* re-start */
+			return;
+		}
+		lradc->ts_y_pos = val;
+		mxs_lradc_prepare_x_pos(lradc);
+		return;
+
+	case LRADC_SAMPLE_X:
+		val = mxs_lradc_read_ts_channel(lradc);
+		if (val < 0) {
+			mxs_lradc_enable_touch_detection(lradc); /* re-start */
+			return;
+		}
+		lradc->ts_x_pos = val;
+		mxs_lradc_prepare_pressure(lradc);
+		return;
+
+	case LRADC_SAMPLE_PRESSURE:
+		lradc->ts_pressure =
+			mxs_lradc_read_ts_pressure(lradc, TS_CH_XP, TS_CH_YM);
+		mxs_lradc_complete_touch_event(lradc);
+		return;
+
+	case LRADC_SAMPLE_VALID:
+		val = mxs_lradc_read_ts_channel(lradc); /* ignore the value */
+		mxs_lradc_finish_touch_event(lradc, 1);
+		break;
+	}
+}
+
 /*
  * Raw I/O operations
  */
@@ -395,15 +830,6 @@ static const struct iio_info mxs_lradc_iio_info = {
 	.read_raw		= mxs_lradc_read_raw,
 };
 
-/*
- * Touchscreen handling
- */
-enum lradc_ts_plate {
-	LRADC_SAMPLE_X,
-	LRADC_SAMPLE_Y,
-	LRADC_SAMPLE_PRESSURE,
-};
-
 static int mxs_lradc_ts_touched(struct mxs_lradc *lradc)
 {
 	uint32_t reg;
@@ -561,10 +987,6 @@ static void mxs_lradc_ts_work(struct work_struct *ts_work)
 	input_report_key(lradc->ts_input, BTN_TOUCH, 0);
 	input_sync(lradc->ts_input);
 
-	/* Do not restart the TS IRQ if the driver is shutting down. */
-	if (lradc->stop_touchscreen)
-		return;
-
 	/* Restart the touchscreen interrupts. */
 	mxs_lradc_reg_clear(lradc, LRADC_CTRL1_TOUCH_DETECT_IRQ, LRADC_CTRL1);
 	mxs_lradc_reg_set(lradc, LRADC_CTRL1_TOUCH_DETECT_IRQ_EN, LRADC_CTRL1);
@@ -574,36 +996,29 @@ static int mxs_lradc_ts_open(struct input_dev *dev)
 {
 	struct mxs_lradc *lradc = input_get_drvdata(dev);
 
-	/* The touchscreen is starting. */
-	lradc->stop_touchscreen = false;
-
 	/* Enable the touch-detect circuitry. */
-	mxs_lradc_reg_set(lradc, mxs_lradc_touch_detect_bit(lradc),
-						LRADC_CTRL0);
-
-	/* Enable the touch-detect IRQ. */
-	mxs_lradc_reg_set(lradc, LRADC_CTRL1_TOUCH_DETECT_IRQ_EN, LRADC_CTRL1);
+	mxs_lradc_enable_touch_detection(lradc);
 
 	return 0;
 }
 
-static void mxs_lradc_ts_close(struct input_dev *dev)
+static void mxs_lradc_disable_ts(struct mxs_lradc *lradc)
 {
-	struct mxs_lradc *lradc = input_get_drvdata(dev);
-
-	/* Indicate the touchscreen is stopping. */
-	lradc->stop_touchscreen = true;
-	mb();
+	/* stop all interrupts from firing */
+	mxs_lradc_reg_clear(lradc, LRADC_CTRL1_TOUCH_DETECT_IRQ_EN |
+		LRADC_CTRL1_LRADC_IRQ_EN(2) | LRADC_CTRL1_LRADC_IRQ_EN(3) |
+		LRADC_CTRL1_LRADC_IRQ_EN(4) | LRADC_CTRL1_LRADC_IRQ_EN(5),
+		LRADC_CTRL1);
 
-	/* Wait until touchscreen thread finishes any possible remnants. */
-	cancel_work_sync(&lradc->ts_work);
+	/* Power-down touchscreen touch-detect circuitry. */
+	mxs_lradc_reg_clear(lradc, mxs_lradc_plate_mask(lradc), LRADC_CTRL0);
+}
 
-	/* Disable touchscreen touch-detect IRQ. */
-	mxs_lradc_reg_clear(lradc, LRADC_CTRL1_TOUCH_DETECT_IRQ_EN,
-						LRADC_CTRL1);
+static void mxs_lradc_ts_close(struct input_dev *dev)
+{
+	struct mxs_lradc *lradc = input_get_drvdata(dev);
 
-	/* Power-down touchscreen touch-detect circuitry. */
-	mxs_lradc_reg_clear(lradc, mxs_lradc_touch_detect_bit(lradc), LRADC_CTRL0);
+	mxs_lradc_disable_ts(lradc);
 }
 
 static int mxs_lradc_ts_register(struct mxs_lradc *lradc)
@@ -649,8 +1064,7 @@ static void mxs_lradc_ts_unregister(struct mxs_lradc *lradc)
 	if (!lradc->use_touchscreen)
 		return;
 
-	cancel_work_sync(&lradc->ts_work);
-
+	mxs_lradc_disable_ts(lradc);
 	input_unregister_device(lradc->ts_input);
 }
 
@@ -663,22 +1077,17 @@ static irqreturn_t mxs_lradc_handle_irq(int irq, void *data)
 	struct mxs_lradc *lradc = iio_priv(iio);
 	unsigned long reg = readl(lradc->base + LRADC_CTRL1);
 	const uint32_t ts_irq_mask =
-		LRADC_CTRL1_TOUCH_DETECT_IRQ_EN |
-		LRADC_CTRL1_TOUCH_DETECT_IRQ;
+		LRADC_CTRL1_TOUCH_DETECT_IRQ |
+		LRADC_CTRL1_LRADC_IRQ(2) |
+		LRADC_CTRL1_LRADC_IRQ(3) |
+		LRADC_CTRL1_LRADC_IRQ(4) |
+		LRADC_CTRL1_LRADC_IRQ(5);
 
 	if (!(reg & mxs_lradc_irq_mask(lradc)))
 		return IRQ_NONE;
 
-	/*
-	 * Touchscreen IRQ handling code has priority and therefore
-	 * is placed here. In case touchscreen IRQ arrives, disable
-	 * it ASAP
-	 */
-	if (reg & LRADC_CTRL1_TOUCH_DETECT_IRQ) {
-		mxs_lradc_reg_clear(lradc, ts_irq_mask, LRADC_CTRL1);
-		if (!lradc->stop_touchscreen)
-			schedule_work(&lradc->ts_work);
-	}
+	if (lradc->use_touchscreen && (reg & ts_irq_mask))
+		mxs_lradc_handle_touch(lradc);
 
 	if (iio_buffer_enabled(iio))
 		iio_trigger_poll(iio->trig, iio_get_time_ns());
@@ -981,6 +1390,17 @@ static const struct of_device_id mxs_lradc_dt_ids[] = {
 };
 MODULE_DEVICE_TABLE(of, mxs_lradc_dt_ids);
 
+static int mxs_lradc_probe_touchscreen(struct mxs_lradc *lradc,
+						struct device_node *lradc_node)
+{
+	/* TODO retrieve from device tree */
+	lradc->over_sample_cnt = 4;
+	lradc->over_sample_delay = 2;
+	lradc->settling_delay = 10;
+
+	return 0;
+}
+
 static int mxs_lradc_probe(struct platform_device *pdev)
 {
 	const struct of_device_id *of_id =
@@ -993,7 +1413,7 @@ static int mxs_lradc_probe(struct platform_device *pdev)
 	struct iio_dev *iio;
 	struct resource *iores;
 	uint32_t ts_wires = 0;
-	int ret = 0;
+	int ret = 0, touch_ret;
 	int i;
 
 	/* Allocate the IIO device. */
@@ -1016,7 +1436,7 @@ static int mxs_lradc_probe(struct platform_device *pdev)
 	lradc->clk = devm_clk_get(&pdev->dev, NULL);
 	clk_prepare_enable(lradc->clk);
 
-	INIT_WORK(&lradc->ts_work, mxs_lradc_ts_work);
+	touch_ret = mxs_lradc_probe_touchscreen(lradc, node);
 
 	/* Check if touchscreen is enabled in DT. */
 	ret = of_property_read_u32(node, "fsl,lradc-touchscreen-wires",
@@ -1079,9 +1499,11 @@ static int mxs_lradc_probe(struct platform_device *pdev)
 		goto err_dev;
 
 	/* Register the touchscreen input device. */
-	ret = mxs_lradc_ts_register(lradc);
-	if (ret)
-		goto err_dev;
+	if (touch_ret == 0) {
+		ret = mxs_lradc_ts_register(lradc);
+		if (ret)
+			goto err_dev;
+	}
 
 	/* Register IIO device. */
 	ret = iio_device_register(iio);
Signature · 1 line
1.8.4.rc3
#17 lore raw

PATCH 6/9 Staging/iio/adc/touchscreen/MXS: add interrupt driven touch detection

Hi Jonathan,

Quoted 1 line · On Tuesday 01 October 2013 11:25:46 Jonathan Cameron wrote:

a couple of the patch descriptions say that they are untested on i.MX28.

Quoted 7 lines · On Monday 23 September 2013 16:36:35 Juergen Beisert wrote:

For battery driven systems it is a very bad idea to collect the touchscreen data within a kernel busy loop.

This change uses the features of the hardware to delay and accumulate samples in hardware to avoid a high interrupt and CPU load.

Note: this is only tested on an i.MX23 SoC yet.

This note is no longer true. Marek tested it on his M28EVK, Lothar on his TX28 and myself also on an i.MX28EVK.

For the IIO part of the driver I tested on my i.MX23 based ChumbyOne and some customer hardware and it seems still to work (I can only guess if the values I read from the sysfs entries are correct, sorry).

Regards,
Juergen

Signature · 2 lines
Pengutronix e.K. ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?| Juergen Beisert ? ? ? ? ? ? |
Linux Solutions for Science and Industry ? ? ?| http://www.pengutronix.de/  |
maintainer
#18 lore raw

PATCH 6/9 Staging/iio/adc/touchscreen/MXS: add interrupt driven touch detection

Quoted 12 lines · Jürgen Beisert

Hi Jonathan,

Quoted 1 line · On Tuesday 01 October 2013 11:25:46 Jonathan Cameron wrote:

a couple of the patch descriptions say that they are untested on i.MX28.

Quoted 6 lines · On Monday 23 September 2013 16:36:35 Juergen Beisert wrote:

For battery driven systems it is a very bad idea to collect the touchscreen data within a kernel busy loop.

This change uses the features of the hardware to delay and accumulate samples in hardware to avoid a high interrupt and CPU load.

Quoted 8 lines
Quoted 1 line

Note: this is only tested on an i.MX23 SoC yet.

This note is no longer true. Marek tested it on his M28EVK, Lothar on his TX28 and myself also on an i.MX28EVK.

For the IIO part of the driver I tested on my i.MX23 based ChumbyOne and some customer hardware and it seems still to work (I can only guess if the values I read from the sysfs entries are correct, sorry).

Excellent. I'll assume everyone is happy then and add some appropriate tested-by tags. I'd missed Marek's reply saying he was fine with this.

Thanks,

Jonathan

Quoted 4 lines

Regards,
Juergen

maintainer
#19 lore raw

PATCH 6/9 Staging/iio/adc/touchscreen/MXS: add interrupt driven touch detection

Quoted 18 lines · Jonathan Cameron
Quoted 17 lines · Jürgen Beisert

Hi Jonathan,

Quoted 1 line · On Tuesday 01 October 2013 11:25:46 Jonathan Cameron wrote:

a couple of the patch descriptions say that they are untested on i.MX28.

Quoted 7 lines · On Monday 23 September 2013 16:36:35 Juergen Beisert wrote:

For battery driven systems it is a very bad idea to collect the touchscreen data within a kernel busy loop.

This change uses the features of the hardware to delay and accumulate samples in hardware to avoid a high interrupt and CPU load.

Note: this is only tested on an i.MX23 SoC yet.

This note is no longer true. Marek tested it on his M28EVK, Lothar on his TX28 and myself also on an i.MX28EVK.

Quoted 6 lines
Quoted 3 lines

For the IIO part of the driver I tested on my i.MX23 based ChumbyOne and some customer hardware and it seems still to work (I can only guess if the values I read from the sysfs entries are correct, sorry).

Excellent. I'll assume everyone is happy then and add some appropriate tested-by tags. I'd missed Marek's reply saying he was fine with this.

This one is not applying cleanly. I've merged what I think is the right fixup, but please check.

The issue is around the error handling after mxs_lradc_ts_register which has been changed in the meantime it seems.

Jonathan

Quoted 14 lines

Thanks,

Jonathan

Quoted 4 lines

Regards,
Juergen

--
To unsubscribe from this list: send the line "unsubscribe linux-iio" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html

#20 lore raw

PATCH 7/9 Staging/iio/adc/touchscreen/MXS: remove old touchscreen detection implementation

In reply to Juergen Beisert
CC linux-arm-kernel at lists.infradead.org
CC linux-input at vger.kernel.org
CC devel at driverdev.osuosl.org
CC Marek Vasut <[email protected]>
CC Fabio Estevam <[email protected]>
CC Jonathan Cameron <[email protected]>
---
 drivers/staging/iio/adc/mxs-lradc.c | 163 ------------------------------------
 1 file changed, 163 deletions(-)
drivers/staging/iio/adc/mxs-lradc.c +0 -163
index 76a900d..aa1f337 100644
@@ -186,7 +186,6 @@ struct mxs_lradc {
 	bool			use_touchbutton;
 
 	struct input_dev	*ts_input;
-	struct work_struct	ts_work;
 
 	enum mxs_lradc_id	soc;
 	enum lradc_ts_plate	cur_plate; /* statemachine */
@@ -830,168 +829,6 @@ static const struct iio_info mxs_lradc_iio_info = {
 	.read_raw		= mxs_lradc_read_raw,
 };
 
-static int mxs_lradc_ts_touched(struct mxs_lradc *lradc)
-{
-	uint32_t reg;
-
-	/* Enable touch detection. */
-	mxs_lradc_reg_clear(lradc, mxs_lradc_plate_mask(lradc), LRADC_CTRL0);
-	mxs_lradc_reg_set(lradc, mxs_lradc_touch_detect_bit(lradc),
-								LRADC_CTRL0);
-
-	msleep(LRADC_TS_SAMPLE_DELAY_MS);
-
-	reg = readl(lradc->base + LRADC_STATUS);
-
-	return reg & LRADC_STATUS_TOUCH_DETECT_RAW;
-}
-
-static int32_t mxs_lradc_ts_sample(struct mxs_lradc *lradc,
-				enum lradc_ts_plate plate, int change)
-{
-	unsigned long delay, jiff;
-	uint32_t reg, ctrl0 = 0, chan = 0;
-	/* The touchscreen always uses CTRL4 slot #7. */
-	const uint8_t slot = 7;
-	uint32_t val;
-
-	/*
-	 * There are three correct configurations of the controller sampling
-	 * the touchscreen, each of these configuration provides different
-	 * information from the touchscreen.
-	 *
-	 * The following table describes the sampling configurations:
-	 * +-------------+-------+-------+-------+
-	 * | Wire \ Axis |   X   |   Y   |   Z   |
-	 * +---------------------+-------+-------+
-	 * |   X+ (CH2)  |   HI  |   TS  |   TS  |
-	 * +-------------+-------+-------+-------+
-	 * |   X- (CH4)  |   LO  |   SH  |   HI  |
-	 * +-------------+-------+-------+-------+
-	 * |   Y+ (CH3)  |   SH  |   HI  |   HI  |
-	 * +-------------+-------+-------+-------+
-	 * |   Y- (CH5)  |   TS  |   LO  |   SH  |
-	 * +-------------+-------+-------+-------+
-	 *
-	 * HI ... strong '1'  ; LO ... strong '0'
-	 * SH ... sample here ; TS ... tri-state
-	 *
-	 * There are a few other ways of obtaining the Z coordinate
-	 * (aka. pressure), but the one in the table seems to be the
-	 * most reliable one.
-	 */
-	switch (plate) {
-	case LRADC_SAMPLE_X:
-		ctrl0 = mxs_lradc_drive_x_plate(lradc);
-		chan = 3;
-		break;
-	case LRADC_SAMPLE_Y:
-		ctrl0 = mxs_lradc_drive_y_plate(lradc);
-		chan = 4;
-		break;
-	case LRADC_SAMPLE_PRESSURE:
-		ctrl0 = mxs_lradc_drive_pressure(lradc);
-		chan = 5;
-		break;
-	}
-
-	if (change) {
-		mxs_lradc_reg_clear(lradc, mxs_lradc_plate_mask(lradc),
-						LRADC_CTRL0);
-		mxs_lradc_reg_set(lradc, ctrl0, LRADC_CTRL0);
-
-		mxs_lradc_reg_clear(lradc, LRADC_CTRL4_LRADCSELECT_MASK(slot),
-						LRADC_CTRL4);
-		mxs_lradc_reg_set(lradc,
-				chan << LRADC_CTRL4_LRADCSELECT_OFFSET(slot),
-				LRADC_CTRL4);
-	}
-
-	mxs_lradc_reg_clear(lradc, 0xffffffff, LRADC_CH(slot));
-	mxs_lradc_reg_set(lradc, 1 << slot, LRADC_CTRL0);
-
-	delay = jiffies + msecs_to_jiffies(LRADC_TS_SAMPLE_DELAY_MS);
-	do {
-		jiff = jiffies;
-		reg = readl_relaxed(lradc->base + LRADC_CTRL1);
-		if (reg & LRADC_CTRL1_LRADC_IRQ(slot))
-			break;
-	} while (time_before(jiff, delay));
-
-	mxs_lradc_reg_clear(lradc, LRADC_CTRL1_LRADC_IRQ(slot), LRADC_CTRL1);
-
-	if (time_after_eq(jiff, delay))
-		return -ETIMEDOUT;
-
-	val = readl(lradc->base + LRADC_CH(slot));
-	val &= LRADC_CH_VALUE_MASK;
-
-	return val;
-}
-
-static int32_t mxs_lradc_ts_sample_filter(struct mxs_lradc *lradc,
-				enum lradc_ts_plate plate)
-{
-	int32_t val, tot = 0;
-	int i;
-
-	val = mxs_lradc_ts_sample(lradc, plate, 1);
-
-	/* Delay a bit so the touchscreen is stable. */
-	mdelay(2);
-
-	for (i = 0; i < LRADC_TS_SAMPLE_AMOUNT; i++) {
-		val = mxs_lradc_ts_sample(lradc, plate, 0);
-		tot += val;
-	}
-
-	return tot / LRADC_TS_SAMPLE_AMOUNT;
-}
-
-static void mxs_lradc_ts_work(struct work_struct *ts_work)
-{
-	struct mxs_lradc *lradc = container_of(ts_work,
-				struct mxs_lradc, ts_work);
-	int val_x, val_y, val_p;
-	bool valid = false;
-
-	while (mxs_lradc_ts_touched(lradc)) {
-		/* Disable touch detector so we can sample the touchscreen. */
-		mxs_lradc_reg_clear(lradc, mxs_lradc_touch_detect_bit(lradc),
-						LRADC_CTRL0);
-
-		if (likely(valid)) {
-			input_report_abs(lradc->ts_input, ABS_X, val_x);
-			input_report_abs(lradc->ts_input, ABS_Y, val_y);
-			input_report_abs(lradc->ts_input, ABS_PRESSURE, val_p);
-			input_report_key(lradc->ts_input, BTN_TOUCH, 1);
-			input_sync(lradc->ts_input);
-		}
-
-		valid = false;
-
-		val_x = mxs_lradc_ts_sample_filter(lradc, LRADC_SAMPLE_X);
-		if (val_x < 0)
-			continue;
-		val_y = mxs_lradc_ts_sample_filter(lradc, LRADC_SAMPLE_Y);
-		if (val_y < 0)
-			continue;
-		val_p = mxs_lradc_ts_sample_filter(lradc, LRADC_SAMPLE_PRESSURE);
-		if (val_p < 0)
-			continue;
-
-		valid = true;
-	}
-
-	input_report_abs(lradc->ts_input, ABS_PRESSURE, 0);
-	input_report_key(lradc->ts_input, BTN_TOUCH, 0);
-	input_sync(lradc->ts_input);
-
-	/* Restart the touchscreen interrupts. */
-	mxs_lradc_reg_clear(lradc, LRADC_CTRL1_TOUCH_DETECT_IRQ, LRADC_CTRL1);
-	mxs_lradc_reg_set(lradc, LRADC_CTRL1_TOUCH_DETECT_IRQ_EN, LRADC_CTRL1);
-}
-
 static int mxs_lradc_ts_open(struct input_dev *dev)
 {
 	struct mxs_lradc *lradc = input_get_drvdata(dev);
Signature · 1 line
1.8.4.rc3
maintainer Applied
#21 lore raw

PATCH 7/9 Staging/iio/adc/touchscreen/MXS: remove old touchscreen detection implementation

Quoted 7 lines · Juergen Beisert

Applied to the togreg branch of iio.git
Thanks,

Quoted 186 lines
---
 drivers/staging/iio/adc/mxs-lradc.c | 163 ------------------------------------
 1 file changed, 163 deletions(-)
drivers/staging/iio/adc/mxs-lradc.c +0 -163
index 76a900d..aa1f337 100644
@@ -186,7 +186,6 @@ struct mxs_lradc {
 	bool			use_touchbutton;
 
 	struct input_dev	*ts_input;
-	struct work_struct	ts_work;
 
 	enum mxs_lradc_id	soc;
 	enum lradc_ts_plate	cur_plate; /* statemachine */
@@ -830,168 +829,6 @@ static const struct iio_info mxs_lradc_iio_info = {
 	.read_raw		= mxs_lradc_read_raw,
 };
 
-static int mxs_lradc_ts_touched(struct mxs_lradc *lradc)
-{
-	uint32_t reg;
-
-	/* Enable touch detection. */
-	mxs_lradc_reg_clear(lradc, mxs_lradc_plate_mask(lradc), LRADC_CTRL0);
-	mxs_lradc_reg_set(lradc, mxs_lradc_touch_detect_bit(lradc),
-								LRADC_CTRL0);
-
-	msleep(LRADC_TS_SAMPLE_DELAY_MS);
-
-	reg = readl(lradc->base + LRADC_STATUS);
-
-	return reg & LRADC_STATUS_TOUCH_DETECT_RAW;
-}
-
-static int32_t mxs_lradc_ts_sample(struct mxs_lradc *lradc,
-				enum lradc_ts_plate plate, int change)
-{
-	unsigned long delay, jiff;
-	uint32_t reg, ctrl0 = 0, chan = 0;
-	/* The touchscreen always uses CTRL4 slot #7. */
-	const uint8_t slot = 7;
-	uint32_t val;
-
-	/*
-	 * There are three correct configurations of the controller sampling
-	 * the touchscreen, each of these configuration provides different
-	 * information from the touchscreen.
-	 *
-	 * The following table describes the sampling configurations:
-	 * +-------------+-------+-------+-------+
-	 * | Wire \ Axis |   X   |   Y   |   Z   |
-	 * +---------------------+-------+-------+
-	 * |   X+ (CH2)  |   HI  |   TS  |   TS  |
-	 * +-------------+-------+-------+-------+
-	 * |   X- (CH4)  |   LO  |   SH  |   HI  |
-	 * +-------------+-------+-------+-------+
-	 * |   Y+ (CH3)  |   SH  |   HI  |   HI  |
-	 * +-------------+-------+-------+-------+
-	 * |   Y- (CH5)  |   TS  |   LO  |   SH  |
-	 * +-------------+-------+-------+-------+
-	 *
-	 * HI ... strong '1'  ; LO ... strong '0'
-	 * SH ... sample here ; TS ... tri-state
-	 *
-	 * There are a few other ways of obtaining the Z coordinate
-	 * (aka. pressure), but the one in the table seems to be the
-	 * most reliable one.
-	 */
-	switch (plate) {
-	case LRADC_SAMPLE_X:
-		ctrl0 = mxs_lradc_drive_x_plate(lradc);
-		chan = 3;
-		break;
-	case LRADC_SAMPLE_Y:
-		ctrl0 = mxs_lradc_drive_y_plate(lradc);
-		chan = 4;
-		break;
-	case LRADC_SAMPLE_PRESSURE:
-		ctrl0 = mxs_lradc_drive_pressure(lradc);
-		chan = 5;
-		break;
-	}
-
-	if (change) {
-		mxs_lradc_reg_clear(lradc, mxs_lradc_plate_mask(lradc),
-						LRADC_CTRL0);
-		mxs_lradc_reg_set(lradc, ctrl0, LRADC_CTRL0);
-
-		mxs_lradc_reg_clear(lradc, LRADC_CTRL4_LRADCSELECT_MASK(slot),
-						LRADC_CTRL4);
-		mxs_lradc_reg_set(lradc,
-				chan << LRADC_CTRL4_LRADCSELECT_OFFSET(slot),
-				LRADC_CTRL4);
-	}
-
-	mxs_lradc_reg_clear(lradc, 0xffffffff, LRADC_CH(slot));
-	mxs_lradc_reg_set(lradc, 1 << slot, LRADC_CTRL0);
-
-	delay = jiffies + msecs_to_jiffies(LRADC_TS_SAMPLE_DELAY_MS);
-	do {
-		jiff = jiffies;
-		reg = readl_relaxed(lradc->base + LRADC_CTRL1);
-		if (reg & LRADC_CTRL1_LRADC_IRQ(slot))
-			break;
-	} while (time_before(jiff, delay));
-
-	mxs_lradc_reg_clear(lradc, LRADC_CTRL1_LRADC_IRQ(slot), LRADC_CTRL1);
-
-	if (time_after_eq(jiff, delay))
-		return -ETIMEDOUT;
-
-	val = readl(lradc->base + LRADC_CH(slot));
-	val &= LRADC_CH_VALUE_MASK;
-
-	return val;
-}
-
-static int32_t mxs_lradc_ts_sample_filter(struct mxs_lradc *lradc,
-				enum lradc_ts_plate plate)
-{
-	int32_t val, tot = 0;
-	int i;
-
-	val = mxs_lradc_ts_sample(lradc, plate, 1);
-
-	/* Delay a bit so the touchscreen is stable. */
-	mdelay(2);
-
-	for (i = 0; i < LRADC_TS_SAMPLE_AMOUNT; i++) {
-		val = mxs_lradc_ts_sample(lradc, plate, 0);
-		tot += val;
-	}
-
-	return tot / LRADC_TS_SAMPLE_AMOUNT;
-}
-
-static void mxs_lradc_ts_work(struct work_struct *ts_work)
-{
-	struct mxs_lradc *lradc = container_of(ts_work,
-				struct mxs_lradc, ts_work);
-	int val_x, val_y, val_p;
-	bool valid = false;
-
-	while (mxs_lradc_ts_touched(lradc)) {
-		/* Disable touch detector so we can sample the touchscreen. */
-		mxs_lradc_reg_clear(lradc, mxs_lradc_touch_detect_bit(lradc),
-						LRADC_CTRL0);
-
-		if (likely(valid)) {
-			input_report_abs(lradc->ts_input, ABS_X, val_x);
-			input_report_abs(lradc->ts_input, ABS_Y, val_y);
-			input_report_abs(lradc->ts_input, ABS_PRESSURE, val_p);
-			input_report_key(lradc->ts_input, BTN_TOUCH, 1);
-			input_sync(lradc->ts_input);
-		}
-
-		valid = false;
-
-		val_x = mxs_lradc_ts_sample_filter(lradc, LRADC_SAMPLE_X);
-		if (val_x < 0)
-			continue;
-		val_y = mxs_lradc_ts_sample_filter(lradc, LRADC_SAMPLE_Y);
-		if (val_y < 0)
-			continue;
-		val_p = mxs_lradc_ts_sample_filter(lradc, LRADC_SAMPLE_PRESSURE);
-		if (val_p < 0)
-			continue;
-
-		valid = true;
-	}
-
-	input_report_abs(lradc->ts_input, ABS_PRESSURE, 0);
-	input_report_key(lradc->ts_input, BTN_TOUCH, 0);
-	input_sync(lradc->ts_input);
-
-	/* Restart the touchscreen interrupts. */
-	mxs_lradc_reg_clear(lradc, LRADC_CTRL1_TOUCH_DETECT_IRQ, LRADC_CTRL1);
-	mxs_lradc_reg_set(lradc, LRADC_CTRL1_TOUCH_DETECT_IRQ_EN, LRADC_CTRL1);
-}
-
 static int mxs_lradc_ts_open(struct input_dev *dev)
 {
 	struct mxs_lradc *lradc = input_get_drvdata(dev);
#22 lore raw

PATCH 8/9 Staging/iio/adc/touchscreen/MXS: provide devicetree adaption

In reply to Juergen Beisert

This is an RFC for the new touchscreen properties.

CC linux-arm-kernel at lists.infradead.org
CC linux-input at vger.kernel.org
CC devel at driverdev.osuosl.org
CC Marek Vasut <[email protected]>
CC Fabio Estevam <[email protected]>
CC Jonathan Cameron <[email protected]>
CC devicetree at vger.kernel.org
---
 .../bindings/staging/iio/adc/mxs-lradc.txt         | 36 ++++++++++++--
 arch/arm/boot/dts/imx28-evk.dts                    |  4 ++
 drivers/staging/iio/adc/mxs-lradc.c                | 57 ++++++++++++++--------
 3 files changed, 71 insertions(+), 26 deletions(-)
Documentation/devicetree/bindings/staging/iio/adc/mxs-lradc.txt +31 -5
index 4688205..ee05dc3 100644
@@ -1,7 +1,8 @@
 * Freescale i.MX28 LRADC device driver
 
 Required properties:
-- compatible: Should be "fsl,imx28-lradc"
+- compatible: Should be "fsl,imx23-lradc" for i.MX23 SoC and "fsl,imx28-lradc"
+              for i.MX28 SoC
 - reg: Address and length of the register set for the device
 - interrupts: Should contain the LRADC interrupts
 
@@ -9,13 +10,38 @@ Optional properties:
 - fsl,lradc-touchscreen-wires: Number of wires used to connect the touchscreen
                                to LRADC. Valid value is either 4 or 5. If this
                                property is not present, then the touchscreen is
-                               disabled.
+                               disabled. 5 wires is valid for i.MX28 SoC only.
+- fsl,ave-ctrl: number of samples per direction to calculate an average value.
+                Allowed value is 1 ... 31, default is 4
+- fsl,ave-delay: delay between consecutive samples. Allowed value is
+                 1 ... 2047. It is used if 'fsl,ave-ctrl' > 1, counts at
+                 2 kHz and its default is 2 (= 1 ms)
+- fsl,settling: delay between plate switch to next sample. Allowed value is
+                1 ... 2047. It counts at 2 kHz and its default is
+                10 (= 5 ms)
 
-Examples:
+Example for i.MX23 SoC:
+
+	lradc at 80050000 {
+		compatible = "fsl,imx23-lradc";
+		reg = <0x80050000 0x2000>;
+		interrupts = <36 37 38 39 40 41 42 43 44>;
+		status = "okay";
+		fsl,lradc-touchscreen-wires = <4>;
+		fsl,ave-ctrl = <4>;
+		fsl,ave-delay = <2>;
+		fsl,settling = <10>;
+	};
+
+Example for i.MX28 SoC:
 
 	lradc at 80050000 {
 		compatible = "fsl,imx28-lradc";
 		reg = <0x80050000 0x2000>;
-		interrupts = <10 14 15 16 17 18 19
-				20 21 22 23 24 25>;
+		interrupts = <10 14 15 16 17 18 19 20 21 22 23 24 25>;
+		status = "okay";
+		fsl,lradc-touchscreen-wires = <5>;
+		fsl,ave-ctrl = <4>;
+		fsl,ave-delay = <2>;
+		fsl,settling = <10>;
 	};
arch/arm/boot/dts/imx28-evk.dts +4 -0
index 15715d9..aa33393 100644
@@ -183,6 +183,10 @@
 
 			lradc at 80050000 {
 				status = "okay";
+				fsl,lradc-touchscreen-wires = <4>;
+				fsl,ave-ctrl = <4>;
+				fsl,ave-delay = <2>;
+				fsl,settling = <10>;
 			};
 
 			i2c0: i2c at 80058000 {
drivers/staging/iio/adc/mxs-lradc.c +36 -21

78 lines not on this page · raw message

Signature · 1 line
1.8.4.rc3
maintainer Applied
#23 lore raw

PATCH 8/9 Staging/iio/adc/touchscreen/MXS: provide devicetree adaption

Quoted 10 lines · Juergen Beisert

This is an RFC for the new touchscreen properties.

Applied to the togreg branch of iio.git

Thanks,

Quoted 164 lines
---
 .../bindings/staging/iio/adc/mxs-lradc.txt         | 36 ++++++++++++--
 arch/arm/boot/dts/imx28-evk.dts                    |  4 ++
 drivers/staging/iio/adc/mxs-lradc.c                | 57 ++++++++++++++--------
 3 files changed, 71 insertions(+), 26 deletions(-)
Documentation/devicetree/bindings/staging/iio/adc/mxs-lradc.txt +31 -5
index 4688205..ee05dc3 100644
@@ -1,7 +1,8 @@
 * Freescale i.MX28 LRADC device driver
 
 Required properties:
-- compatible: Should be "fsl,imx28-lradc"
+- compatible: Should be "fsl,imx23-lradc" for i.MX23 SoC and "fsl,imx28-lradc"
+              for i.MX28 SoC
 - reg: Address and length of the register set for the device
 - interrupts: Should contain the LRADC interrupts
 
@@ -9,13 +10,38 @@ Optional properties:
 - fsl,lradc-touchscreen-wires: Number of wires used to connect the touchscreen
                                to LRADC. Valid value is either 4 or 5. If this
                                property is not present, then the touchscreen is
-                               disabled.
+                               disabled. 5 wires is valid for i.MX28 SoC only.
+- fsl,ave-ctrl: number of samples per direction to calculate an average value.
+                Allowed value is 1 ... 31, default is 4
+- fsl,ave-delay: delay between consecutive samples. Allowed value is
+                 1 ... 2047. It is used if 'fsl,ave-ctrl' > 1, counts at
+                 2 kHz and its default is 2 (= 1 ms)
+- fsl,settling: delay between plate switch to next sample. Allowed value is
+                1 ... 2047. It counts at 2 kHz and its default is
+                10 (= 5 ms)
 
-Examples:
+Example for i.MX23 SoC:
+
+	lradc@80050000 {
+		compatible = "fsl,imx23-lradc";
+		reg = <0x80050000 0x2000>;
+		interrupts = <36 37 38 39 40 41 42 43 44>;
+		status = "okay";
+		fsl,lradc-touchscreen-wires = <4>;
+		fsl,ave-ctrl = <4>;
+		fsl,ave-delay = <2>;
+		fsl,settling = <10>;
+	};
+
+Example for i.MX28 SoC:
 
 	lradc@80050000 {
 		compatible = "fsl,imx28-lradc";
 		reg = <0x80050000 0x2000>;
-		interrupts = <10 14 15 16 17 18 19
-				20 21 22 23 24 25>;
+		interrupts = <10 14 15 16 17 18 19 20 21 22 23 24 25>;
+		status = "okay";
+		fsl,lradc-touchscreen-wires = <5>;
+		fsl,ave-ctrl = <4>;
+		fsl,ave-delay = <2>;
+		fsl,settling = <10>;
 	};
arch/arm/boot/dts/imx28-evk.dts +4 -0
index 15715d9..aa33393 100644
@@ -183,6 +183,10 @@
 
 			lradc@80050000 {
 				status = "okay";
+				fsl,lradc-touchscreen-wires = <4>;
+				fsl,ave-ctrl = <4>;
+				fsl,ave-delay = <2>;
+				fsl,settling = <10>;
 			};
 
 			i2c0: i2c@80058000 {
drivers/staging/iio/adc/mxs-lradc.c +36 -21
index aa1f337..dbc0af6 100644
@@ -1230,10 +1230,45 @@ MODULE_DEVICE_TABLE(of, mxs_lradc_dt_ids);
 static int mxs_lradc_probe_touchscreen(struct mxs_lradc *lradc,
 						struct device_node *lradc_node)
 {
-	/* TODO retrieve from device tree */
+	int ret;
+	u32 ts_wires = 0, adapt;
+
+	ret = of_property_read_u32(lradc_node, "fsl,lradc-touchscreen-wires",
+				&ts_wires);
+	if (ret)
+		return -ENODEV; /* touchscreen feature disabled */
+
+	switch (ts_wires) {
+	case 4:
+		lradc->use_touchscreen = MXS_LRADC_TOUCHSCREEN_4WIRE;
+		break;
+	case 5:
+		if (lradc->soc == IMX28_LRADC) {
+			lradc->use_touchscreen = MXS_LRADC_TOUCHSCREEN_5WIRE;
+			break;
+		}
+		/* fall through an error message for i.MX23 */
+	default:
+		dev_err(lradc->dev,
+			"Unsupported number of touchscreen wires (%d)\n",
+			ts_wires);
+		return -EINVAL;
+	}
+
 	lradc->over_sample_cnt = 4;
+	ret = of_property_read_u32(lradc_node, "fsl,ave-ctrl", &adapt);
+	if (ret == 0)
+		lradc->over_sample_cnt = adapt;
+
 	lradc->over_sample_delay = 2;
+	ret = of_property_read_u32(lradc_node, "fsl,ave-delay", &adapt);
+	if (ret == 0)
+		lradc->over_sample_delay = adapt;
+
 	lradc->settling_delay = 10;
+	ret = of_property_read_u32(lradc_node, "fsl,settling", &adapt);
+	if (ret == 0)
+		lradc->settling_delay = adapt;
 
 	return 0;
 }
@@ -1249,7 +1284,6 @@ static int mxs_lradc_probe(struct platform_device *pdev)
 	struct mxs_lradc *lradc;
 	struct iio_dev *iio;
 	struct resource *iores;
-	uint32_t ts_wires = 0;
 	int ret = 0, touch_ret;
 	int i;
 
@@ -1275,25 +1309,6 @@ static int mxs_lradc_probe(struct platform_device *pdev)
 
 	touch_ret = mxs_lradc_probe_touchscreen(lradc, node);
 
-	/* Check if touchscreen is enabled in DT. */
-	ret = of_property_read_u32(node, "fsl,lradc-touchscreen-wires",
-				&ts_wires);
-	if (ret)
-		dev_info(dev, "Touchscreen not enabled.\n");
-	else if (ts_wires == 4)
-		lradc->use_touchscreen = MXS_LRADC_TOUCHSCREEN_4WIRE;
-	else if (ts_wires == 5)
-		lradc->use_touchscreen = MXS_LRADC_TOUCHSCREEN_5WIRE;
-	else
-		dev_warn(dev, "Unsupported number of touchscreen wires (%d)\n",
-				ts_wires);
-
-	if ((lradc->soc == IMX23_LRADC) && (ts_wires == 5)) {
-		dev_warn(dev, "No support for 5 wire touches on i.MX23\n");
-		dev_warn(dev, "Falling back to 4 wire\n");
-		ts_wires = 4;
-	}
-
 	/* Grab all IRQ sources */
 	for (i = 0; i < of_cfg->irq_count; i++) {
 		lradc->irq[i] = platform_get_irq(pdev, i);
#24 lore raw

PATCH 9/9 Staging/iio: add TODO reminder

In reply to Juergen Beisert

Some things have still to be done to the LRADC driver.

CC linux-arm-kernel at lists.infradead.org
CC linux-input at vger.kernel.org
CC devel at driverdev.osuosl.org
CC Marek Vasut <[email protected]>
CC Fabio Estevam <[email protected]>
CC Jonathan Cameron <[email protected]>
---
 drivers/staging/iio/TODO | 11 +++++++++++
 1 file changed, 11 insertions(+)
drivers/staging/iio/TODO +11 -0
index 04c2326..c22a0ed 100644
@@ -13,6 +13,17 @@ Would be nice
 3) Expand device set. Lots of other maxim adc's have very
    similar interfaces.
 
+MXS LRADC driver:
+This is a classic MFD device as it combines the following subdevices
+ - touchscreen controller (input subsystem related device)
+ - general purpose ADC channels
+ - battery voltage monitor (power subsystem related device)
+ - die temperature monitor (thermal management)
+
+At least the battery voltage and die temperature feature is required in-kernel
+by a driver of the SoC's battery charging unit to avoid any damage to the
+silicon and the battery.
+
 TSL2561
 Would be nice
 1) Open question of userspace vs kernel space balance when
Signature · 1 line
1.8.4.rc3
maintainer Applied
#25 lore raw

PATCH 9/9 Staging/iio: add TODO reminder

Quoted 9 lines · Juergen Beisert

Some things have still to be done to the LRADC driver.

Applied to the togreg branch of iio.git

Thanks.

Please check over the entire series as it was more than a little fiddly to apply and I may well have messed it up!

Jonathan

Quoted 27 lines
---
 drivers/staging/iio/TODO | 11 +++++++++++
 1 file changed, 11 insertions(+)
drivers/staging/iio/TODO +11 -0
index 04c2326..c22a0ed 100644
@@ -13,6 +13,17 @@ Would be nice
 3) Expand device set. Lots of other maxim adc's have very
    similar interfaces.
 
+MXS LRADC driver:
+This is a classic MFD device as it combines the following subdevices
+ - touchscreen controller (input subsystem related device)
+ - general purpose ADC channels
+ - battery voltage monitor (power subsystem related device)
+ - die temperature monitor (thermal management)
+
+At least the battery voltage and die temperature feature is required in-kernel
+by a driver of the SoC's battery charging unit to avoid any damage to the
+silicon and the battery.
+
 TSL2561
 Would be nice
 1) Open question of userspace vs kernel space balance when
maintainer
#26 lore raw

PATCH 9/9 Staging/iio: add TODO reminder

Quoted 10 lines · Jonathan Cameron
Quoted 9 lines · Juergen Beisert

Some things have still to be done to the LRADC driver.

Quoted 6 lines

Applied to the togreg branch of iio.git

Thanks.

Please check over the entire series as it was more than a little fiddly to apply and I may well have messed it up!

There may be a delay on me pushing this out. Kernel.org isn't talking to me right now for some reason.

Quoted 34 lines

Jonathan

Quoted 17 lines
---
 drivers/staging/iio/TODO | 11 +++++++++++
 1 file changed, 11 insertions(+)
drivers/staging/iio/TODO +4 -0
index 04c2326..c22a0ed 100644
@@ -13,6 +13,17 @@ Would be nice
 3) Expand device set. Lots of other maxim adc's have very
    similar interfaces.
 
+MXS LRADC driver:
+This is a classic MFD device as it combines the following subdevices
+ - touchscreen controller (input subsystem related device)
+ - general purpose ADC channels

drivers/staging/iio/TODO Would be nice · line 29

Quoted 10 lines
drivers/staging/iio/TODO +7 -0
+ - battery voltage monitor (power subsystem related device)
+ - die temperature monitor (thermal management)
+
+At least the battery voltage and die temperature feature is required in-kernel
+by a driver of the SoC's battery charging unit to avoid any damage to the
+silicon and the battery.
+
 TSL2561
 Would be nice
 1) Open question of userspace vs kernel space balance when

--
To unsubscribe from this list: send the line "unsubscribe linux-iio" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html

maintainer
#27 lore raw

PATCH 9/9 Staging/iio: add TODO reminder

Quoted 11 lines · Jonathan Cameron
Quoted 10 lines · Jonathan Cameron
Quoted 9 lines · Juergen Beisert

Some things have still to be done to the LRADC driver.

CC linux-arm-kernel at lists.infradead.org
CC linux-input at vger.kernel.org
CC devel at driverdev.osuosl.org
CC Marek Vasut <[email protected]>
CC Fabio Estevam <[email protected]>
CC Jonathan Cameron <[email protected]>
Quoted 8 lines
Quoted 6 lines

Applied to the togreg branch of iio.git

Thanks.

Please check over the entire series as it was more than a little fiddly to apply and I may well have messed it up!

There may be a delay on me pushing this out. Kernel.org isn't talking to me right now for some reason.

Hmm. Typical, it worked just after I sent this.

Anyhow, all there now.

Quoted 39 lines
Quoted 25 lines

Jonathan

Quoted 23 lines
---
 drivers/staging/iio/TODO | 11 +++++++++++
 1 file changed, 11 insertions(+)
drivers/staging/iio/TODO +11 -0
index 04c2326..c22a0ed 100644
@@ -13,6 +13,17 @@ Would be nice
 3) Expand device set. Lots of other maxim adc's have very
    similar interfaces.
 
+MXS LRADC driver:
+This is a classic MFD device as it combines the following subdevices
+ - touchscreen controller (input subsystem related device)
+ - general purpose ADC channels
+ - battery voltage monitor (power subsystem related device)
+ - die temperature monitor (thermal management)
+
+At least the battery voltage and die temperature feature is required in-kernel
+by a driver of the SoC's battery charging unit to avoid any damage to the
+silicon and the battery.
+
Quoted 9 lines

drivers/staging/iio/TODO Would be nice · line 29

Quoted 4 lines
drivers/staging/iio/TODO +0 -0
 TSL2561
 Would be nice
 1) Open question of userspace vs kernel space balance when

--
To unsubscribe from this list: send the line "unsubscribe linux-iio" in the body of a message to majordomo at vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html

--
To unsubscribe from this list: send the line "unsubscribe linux-iio" in the body of a message to majordomo at vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html

#28 lore raw

PATCH v6 1/1 staging/iio/adc: change the MXS touchscreen driver implementation

In reply to Juergen Beisert

Dear Juergen Beisert,

Quoted 47 lines

The following series replaces the current busy loop touchscreen implementation for i.MX28/i.MX23 SoCs by a fully interrupt driven implementation.

Since i.MX23 and i.MX28 silicon differs, the existing implementation can be used for the i.MX28 SoC only.

The first patch adds proper clock handling. Various platforms seems to disable the internal 2 kHz clock which is used by the LRADC delay units.

The next two patches of this series move the i.MX28 specific definitions out of the way. The forth patch simplifies the register access to make it easier to add the i.MX23 support. Then the i.MX23 specific definitions are added, also the code to distinguish both SoCs at run-time.
Up to here the existing touchscreen driver will now run on an i.MX23 Soc as well.

When these i.MX SoCs are running from battery it seems not to be a good idea to run a busy loop to detect touches and their location. The 6th patch adds a fully interrupt driven implementation which makes use of the built-in delay and multiple sample features of the touchscreen controller. This will reduce the interrupt load to a minimum.

The remaining patches in this series just removes the existing busy loop implementation, add a proposal for devicetree binding and a reminder what has still to be done with the LRADC driver.

Changes since v5:

- add missing clock handling which prevents the delay units from work (this should make it work on the MX28EVK and M28EVK as well)

Changes since v4:

- honor Jonathan's comments about function names
- honor Dmitry's comments about workqueue canceling and interrupts
- adding devicetree bindings proposal

Changes since v3:

- split adding register access functions and i.MX23 support into two patches

Changes since v2:

- useless debug output removed

Quoted 8 lines

Changes since v1:

- adding register access functions to make the existing code more readable
- adding some functions to distinguish the SoCs at run-time to avoid if-else contructs whenever differences in the register layout between i.MX23 and i.MX28 must be handled

Comments are welcome.

On M28EVK:

Thanks!

Best regards,
Marek Vasut

maintainer
#29 lore raw

PATCH v6 1/1 staging/iio/adc: change the MXS touchscreen driver implementation

In reply to Juergen Beisert

I'm looking for some Tested-by: or Acks on this before applying the series. I got the impression from the comments on the previous version that the series has now been reasonably thoroughly tested on both i.MX28 and i.MX23 boards. This is not yet reflected in the sign off trail and in fact a couple of the patch descriptions say that they are untested on i.MX28.

Jonathan

Quoted 60 lines · Juergen Beisert

The following series replaces the current busy loop touchscreen implementation for i.MX28/i.MX23 SoCs by a fully interrupt driven implementation.

Since i.MX23 and i.MX28 silicon differs, the existing implementation can be used for the i.MX28 SoC only.

The first patch adds proper clock handling. Various platforms seems to disable the internal 2 kHz clock which is used by the LRADC delay units.

The next two patches of this series move the i.MX28 specific definitions out of the way. The forth patch simplifies the register access to make it easier to add the i.MX23 support. Then the i.MX23 specific definitions are added, also the code to distinguish both SoCs at run-time.
Up to here the existing touchscreen driver will now run on an i.MX23 Soc as well.

When these i.MX SoCs are running from battery it seems not to be a good idea to run a busy loop to detect touches and their location. The 6th patch adds a fully interrupt driven implementation which makes use of the built-in delay and multiple sample features of the touchscreen controller. This will reduce the interrupt load to a minimum.

The remaining patches in this series just removes the existing busy loop implementation, add a proposal for devicetree binding and a reminder what has still to be done with the LRADC driver.

Changes since v5:

- add missing clock handling which prevents the delay units from work (this should make it work on the MX28EVK and M28EVK as well)

Changes since v4:

- honor Jonathan's comments about function names
- honor Dmitry's comments about workqueue canceling and interrupts
- adding devicetree bindings proposal

Changes since v3:

- split adding register access functions and i.MX23 support into two patches

Changes since v2:

- useless debug output removed

Changes since v1:

- adding register access functions to make the existing code more readable
- adding some functions to distinguish the SoCs at run-time to avoid if-else contructs whenever differences in the register layout between i.MX23 and i.MX28 must be handled

Comments are welcome.

Juergen

--
To unsubscribe from this list: send the line "unsubscribe linux-iio" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html

#30 lore raw

PATCH v6 1/1 staging/iio/adc: change the MXS touchscreen driver implementation

Dear Jonathan Cameron,

Quoted 8 lines

I'm looking for some Tested-by: or Acks on this before applying the series. I got the impression from the comments on the previous version that the series has now been reasonably thoroughly tested on both i.MX28 and i.MX23 boards. This is not yet reflected in the sign off trail and in fact a couple of the patch descriptions say that they are untested on i.MX28.

Jonathan

on M28EVK

Best regards,
Marek Vasut

#31 lore raw

PATCH v6 1/1 staging/iio/adc: change the MXS touchscreen driver implementation

In reply to Juergen Beisert

Hi,

Sorry to chime in only now but it seems that this series is breaking the touchscreen calibration on 3.13 (and -rc7 is out so it might be too late).

At first, I though I became a terrible clicker ;) but I found some evidences:

xinput_calibrator is complaining about misclicks, debug output:
DEBUG: Adding click 0 (X=105, Y=59)
DEBUG: Not adding click 1 (X=100, Y=59): within 7 pixels of previous click
DEBUG: Adding click 1 (X=696, Y=58)
DEBUG: Not adding click 2 (X=700, Y=55): within 7 pixels of previous click
DEBUG: Adding click 2 (X=103, Y=422)
DEBUG: Mis-click detected, click 3 (X=438, Y=415) not aligned with click 1 (X=696, Y=58) or click 2 (X=103, Y=422) (threshold=15)
DEBUG: Adding click 0 (X=424, Y=411)

Do you see the confusion ? At some point one of the coordinates is not updated. Successful calibration with 3.12.6 gives:
DEBUG: Adding click 0 (X=126, Y=405)
DEBUG: Adding click 1 (X=684, Y=399)
DEBUG: Adding click 2 (X=128, Y=77)
DEBUG: Adding click 3 (X=683, Y=77)

With ts_calibrate:
xres = 800, yres = 480
Took 1 samples...
Top left : X = 435 Y = 3572
Took 2 samples...
Top right : X = 2094 Y = 3553
Took 2 samples...
Bot right : X = 2939 Y = 2077
Took 2 samples...
Bot left : X = 2060 Y = 644
Took 2 samples...
Center : X = 1279 Y = 1346

We experience the same thing, when changing position on an axis, we get an average between the previous and the new position (probably because we got 2 samples):
- Top Left is ok
- Top right is almost ok: X should be around 3500/3700
- Bot right is starting to get really wrong: X is getting better (it should still be around 3500/3700) but Y should be quite lower
- Bot left: Y is ok but X should be lower
- Center is completely wrong, both values should be around 2000

Last test with evtest which is always difficult because it outputs a lot of debug. Two separate touchs, bottom left and then top right (note that this is with fsl,ave-ctrl = <8>;):

Event: time 1389210862.451000, type 3 (Absolute), code 0 (X), value 2183
Event: time 1389210862.451000, type 3 (Absolute), code 1 (Y), value 720
Event: time 1389210862.451000, type 3 (Absolute), code 24 (Pressure), value 6
Event: time 1389210862.451000, type 1 (Key), code 330 (Touch), value 1
Event: time 1389210862.451000, -------------- Report Sync ------------
Event: time 1389210862.477721, type 3 (Absolute), code 0 (X), value 448
Event: time 1389210862.477721, type 3 (Absolute), code 1 (Y), value 667
Event: time 1389210862.477721, type 3 (Absolute), code 24 (Pressure), value 595
Event: time 1389210862.477721, -------------- Report Sync ------------
Event: time 1389210862.504718, type 3 (Absolute), code 0 (X), value 434
Event: time 1389210862.504718, type 3 (Absolute), code 1 (Y), value 704
Event: time 1389210862.504718, type 3 (Absolute), code 24 (Pressure), value 580
Event: time 1389210862.504718, -------------- Report Sync ------------
Event: time 1389210862.536688, type 1 (Key), code 330 (Touch), value 0
Event: time 1389210862.536688, -------------- Report Sync ------------
Event: time 1389210863.359697, type 3 (Absolute), code 0 (X), value 432
Event: time 1389210863.359697, type 3 (Absolute), code 1 (Y), value 726
Event: time 1389210863.359697, type 3 (Absolute), code 24 (Pressure), value 210
Event: time 1389210863.359697, type 1 (Key), code 330 (Touch), value 1
Event: time 1389210863.359697, -------------- Report Sync ------------
Event: time 1389210863.391687, type 1 (Key), code 330 (Touch), value 0
Event: time 1389210863.391687, -------------- Report Sync ------------

We get 3 reports for bottom left, then pen up, then one report for top right that is almost exactly the same a bottom left !

Output from 3.12:
Event: time 1389210022.146809, type 3 (Absolute), code 0 (X), value 286
Event: time 1389210022.146809, type 3 (Absolute), code 1 (Y), value 504
Event: time 1389210022.146809, type 3 (Absolute), code 24 (Pressure), value 3045
Event: time 1389210022.146809, type 1 (Key), code 330 (Touch), value 1
Event: time 1389210022.146809, -------------- Report Sync ------------
Event: time 1389210022.166830, type 3 (Absolute), code 0 (X), value 256
Event: time 1389210022.166830, type 3 (Absolute), code 1 (Y), value 489
Event: time 1389210022.166830, type 3 (Absolute), code 24 (Pressure), value 3033
Event: time 1389210022.166830, -------------- Report Sync ------------
Event: time 1389210022.186812, type 3 (Absolute), code 24 (Pressure), value 0
Event: time 1389210022.186812, type 1 (Key), code 330 (Touch), value 0
Event: time 1389210022.186812, -------------- Report Sync ------------
Event: time 1389210025.196808, type 3 (Absolute), code 0 (X), value 3812
Event: time 1389210025.196808, type 3 (Absolute), code 1 (Y), value 3637
Event: time 1389210025.196808, type 3 (Absolute), code 24 (Pressure), value 4032
Event: time 1389210025.196808, type 1 (Key), code 330 (Touch), value 1
Event: time 1389210025.196808, -------------- Report Sync ------------
Event: time 1389210025.216819, type 3 (Absolute), code 24 (Pressure), value 0
Event: time 1389210025.216819, type 1 (Key), code 330 (Touch), value 0
Event: time 1389210025.216819, -------------- Report Sync ------------

While this is not necessarily an issue with ts_calibrate (it is possible to click longer so it collects more samples), I don't see that working with xinput_calibrator.

While I don't have much experience with the TS part of the code but I can investigate if you don't have any idea.

Quoted 60 lines · Juergen Beisert

The following series replaces the current busy loop touchscreen implementation for i.MX28/i.MX23 SoCs by a fully interrupt driven implementation.

Since i.MX23 and i.MX28 silicon differs, the existing implementation can be used for the i.MX28 SoC only.

The first patch adds proper clock handling. Various platforms seems to disable the internal 2 kHz clock which is used by the LRADC delay units.

The next two patches of this series move the i.MX28 specific definitions out of the way. The forth patch simplifies the register access to make it easier to add the i.MX23 support. Then the i.MX23 specific definitions are added, also the code to distinguish both SoCs at run-time.
Up to here the existing touchscreen driver will now run on an i.MX23 Soc as well.

When these i.MX SoCs are running from battery it seems not to be a good idea to run a busy loop to detect touches and their location. The 6th patch adds a fully interrupt driven implementation which makes use of the built-in delay and multiple sample features of the touchscreen controller. This will reduce the interrupt load to a minimum.

The remaining patches in this series just removes the existing busy loop implementation, add a proposal for devicetree binding and a reminder what has still to be done with the LRADC driver.

Changes since v5:

- add missing clock handling which prevents the delay units from work (this should make it work on the MX28EVK and M28EVK as well)

Changes since v4:

- honor Jonathan's comments about function names
- honor Dmitry's comments about workqueue canceling and interrupts
- adding devicetree bindings proposal

Changes since v3:

- split adding register access functions and i.MX23 support into two patches

Changes since v2:

- useless debug output removed

Changes since v1:

- adding register access functions to make the existing code more readable
- adding some functions to distinguish the SoCs at run-time to avoid if-else contructs whenever differences in the register layout between i.MX23 and i.MX28 must be handled

Comments are welcome.

Juergen

--
To unsubscribe from this list: send the line "unsubscribe linux-iio" in the body of a message to majordomo at vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html

Signature · 3 lines
Alexandre Belloni, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
#32 lore raw

PATCH v6 1/1 staging/iio/adc: change the MXS touchscreen driver implementation

Hi Alexandre,

Quoted 100 lines · On Thursday 09 January 2014 14:31:22 Alexandre Belloni wrote:

Sorry to chime in only now but it seems that this series is breaking the touchscreen calibration on 3.13 (and -rc7 is out so it might be too late).

At first, I though I became a terrible clicker ;) but I found some evidences:

xinput_calibrator is complaining about misclicks, debug output:
DEBUG: Adding click 0 (X=105, Y=59)
DEBUG: Not adding click 1 (X=100, Y=59): within 7 pixels of previous click
DEBUG: Adding click 1 (X=696, Y=58)
DEBUG: Not adding click 2 (X=700, Y=55): within 7 pixels of previous click
DEBUG: Adding click 2 (X=103, Y=422)
DEBUG: Mis-click detected, click 3 (X=438, Y=415) not aligned with click 1 (X=696, Y=58) or click 2 (X=103, Y=422) (threshold=15)
DEBUG: Adding click 0 (X=424, Y=411)

Do you see the confusion ? At some point one of the coordinates is not updated. Successful calibration with 3.12.6 gives:
DEBUG: Adding click 0 (X=126, Y=405)
DEBUG: Adding click 1 (X=684, Y=399)
DEBUG: Adding click 2 (X=128, Y=77)
DEBUG: Adding click 3 (X=683, Y=77)

With ts_calibrate:
xres = 800, yres = 480
Took 1 samples...
Top left : X = 435 Y = 3572
Took 2 samples...
Top right : X = 2094 Y = 3553
Took 2 samples...
Bot right : X = 2939 Y = 2077
Took 2 samples...
Bot left : X = 2060 Y = 644
Took 2 samples...
Center : X = 1279 Y = 1346

We experience the same thing, when changing position on an axis, we get an average between the previous and the new position (probably because we got 2 samples):
- Top Left is ok
- Top right is almost ok: X should be around 3500/3700
- Bot right is starting to get really wrong: X is getting better (it should still be around 3500/3700) but Y should be quite lower
- Bot left: Y is ok but X should be lower
- Center is completely wrong, both values should be around 2000

Last test with evtest which is always difficult because it outputs a lot of debug. Two separate touchs, bottom left and then top right (note that this is with fsl,ave-ctrl = <8>;):

Event: time 1389210862.451000, type 3 (Absolute), code 0 (X), value 2183
Event: time 1389210862.451000, type 3 (Absolute), code 1 (Y), value 720
Event: time 1389210862.451000, type 3 (Absolute), code 24 (Pressure), value 6
Event: time 1389210862.451000, type 1 (Key), code 330 (Touch), value 1
Event: time 1389210862.451000, -------------- Report Sync ------------
Event: time 1389210862.477721, type 3 (Absolute), code 0 (X), value 448
Event: time 1389210862.477721, type 3 (Absolute), code 1 (Y), value 667
Event: time 1389210862.477721, type 3 (Absolute), code 24 (Pressure), value 595
Event: time 1389210862.477721, -------------- Report Sync ------------
Event: time 1389210862.504718, type 3 (Absolute), code 0 (X), value 434
Event: time 1389210862.504718, type 3 (Absolute), code 1 (Y), value 704
Event: time 1389210862.504718, type 3 (Absolute), code 24 (Pressure), value 580
Event: time 1389210862.504718, -------------- Report Sync ------------
Event: time 1389210862.536688, type 1 (Key), code 330 (Touch), value 0
Event: time 1389210862.536688, -------------- Report Sync ------------
Event: time 1389210863.359697, type 3 (Absolute), code 0 (X), value 432
Event: time 1389210863.359697, type 3 (Absolute), code 1 (Y), value 726
Event: time 1389210863.359697, type 3 (Absolute), code 24 (Pressure), value 210
Event: time 1389210863.359697, type 1 (Key), code 330 (Touch), value 1
Event: time 1389210863.359697, -------------- Report Sync ------------
Event: time 1389210863.391687, type 1 (Key), code 330 (Touch), value 0
Event: time 1389210863.391687, -------------- Report Sync ------------

We get 3 reports for bottom left, then pen up, then one report for top right that is almost exactly the same a bottom left !

Output from 3.12:
Event: time 1389210022.146809, type 3 (Absolute), code 0 (X), value 286
Event: time 1389210022.146809, type 3 (Absolute), code 1 (Y), value 504
Event: time 1389210022.146809, type 3 (Absolute), code 24 (Pressure), value 3045
Event: time 1389210022.146809, type 1 (Key), code 330 (Touch), value 1
Event: time 1389210022.146809, -------------- Report Sync ------------
Event: time 1389210022.166830, type 3 (Absolute), code 0 (X), value 256
Event: time 1389210022.166830, type 3 (Absolute), code 1 (Y), value 489
Event: time 1389210022.166830, type 3 (Absolute), code 24 (Pressure), value 3033
Event: time 1389210022.166830, -------------- Report Sync ------------
Event: time 1389210022.186812, type 3 (Absolute), code 24 (Pressure), value 0
Event: time 1389210022.186812, type 1 (Key), code 330 (Touch), value 0
Event: time 1389210022.186812, -------------- Report Sync ------------
Event: time 1389210025.196808, type 3 (Absolute), code 0 (X), value 3812
Event: time 1389210025.196808, type 3 (Absolute), code 1 (Y), value 3637
Event: time 1389210025.196808, type 3 (Absolute), code 24 (Pressure), value 4032
Event: time 1389210025.196808, type 1 (Key), code 330 (Touch), value 1
Event: time 1389210025.196808, -------------- Report Sync ------------
Event: time 1389210025.216819, type 3 (Absolute), code 24 (Pressure), value 0
Event: time 1389210025.216819, type 1 (Key), code 330 (Touch), value 0
Event: time 1389210025.216819, -------------- Report Sync ------------

Quoted 6 lines

While this is not necessarily an issue with ts_calibrate (it is possible to click longer so it collects more samples), I don't see that working with xinput_calibrator.

While I don't have much experience with the TS part of the code but I can investigate if you don't have any idea.

You are right. I have seen the same behaviour here a few times. Currently I'm short in time to dig deeper into this issue, but I will try to do so.

Juergen

Signature · 2 lines
Pengutronix e.K. ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?| Juergen Beisert ? ? ? ? ? ? |
Linux Solutions for Science and Industry ? ? ?| http://www.pengutronix.de/  |
#33 lore raw

PATCH v6 1/1 staging/iio/adc: change the MXS touchscreen driver implementation

On Friday, January 10, 2014 at 09:55:45 AM, J?rgen Beisert wrote:

[...]

Quoted 9 lines
Quoted 6 lines

While this is not necessarily an issue with ts_calibrate (it is possible to click longer so it collects more samples), I don't see that working with xinput_calibrator.

While I don't have much experience with the TS part of the code but I can investigate if you don't have any idea.

You are right. I have seen the same behaviour here a few times. Currently I'm short in time to dig deeper into this issue, but I will try to do so.

Hi guys, is this still broken?

Best regards,
Marek Vasut

#34 lore raw

PATCH v6 1/1 staging/iio/adc: change the MXS touchscreen driver implementation

In reply to Jürgen Beisert

Hi Alexandre,

Quoted 2 lines

While I don't have much experience with the TS part of the code but I can investigate if you don't have any idea.

can you please test the following patch?
After releasing the touchscreen the internal state machine was left in a wrong state.

drivers/staging/iio/adc/mxs-lradc.c +1 -0
index e2dd783..558a76c 100644
@@ -698,6 +698,7 @@ static void mxs_lradc_finish_touch_event(struct mxs_lradc *lradc, bool valid)
        }
 
        /* if it is released, wait for the next touch via IRQ */
+       lradc->cur_plate = LRADC_TOUCH;
        mxs_lradc_reg_clear(lradc, LRADC_CTRL1_TOUCH_DETECT_IRQ, LRADC_CTRL1);
        mxs_lradc_reg_set(lradc, LRADC_CTRL1_TOUCH_DETECT_IRQ_EN, LRADC_CTRL1);
 }

Regards,
Juergen

Signature · 4 lines
Pengutronix e.K.                              | Juergen Beisert             |
Linux Solutions for Science and Industry      | Phone: +49-5121-206917-5128 |
Peiner Str. 6-8, 31137 Hildesheim, Germany    | Fax:   +49-5121-206917-5555 |
Amtsgericht Hildesheim, HRA 2686              | http://www.pengutronix.de/  |
#35 lore raw

PATCH v6 1/1 staging/iio/adc: change the MXS touchscreen driver implementation

Quoted 14 lines · Juergen Beisert

Hi Alexandre,

Quoted 2 lines

While I don't have much experience with the TS part of the code but I can investigate if you don't have any idea.

can you please test the following patch?
After releasing the touchscreen the internal state machine was left in a wrong state.

drivers/staging/iio/adc/mxs-lradc.c +0 -0
index e2dd783..558a76c 100644

drivers/staging/iio/adc/mxs-lradc.c static void mxs_lradc_finish_touch_event(struct mxs_lradc *lradc, bool valid) · line 704

Quoted 7 lines
drivers/staging/iio/adc/mxs-lradc.c +1 -0
@@ -698,6 +698,7 @@ static void mxs_lradc_finish_touch_event(struct mxs_lradc *lradc, bool valid)
        }
 
        /* if it is released, wait for the next touch via IRQ */
+       lradc->cur_plate = LRADC_TOUCH;
        mxs_lradc_reg_clear(lradc, LRADC_CTRL1_TOUCH_DETECT_IRQ, LRADC_CTRL1);
        mxs_lradc_reg_set(lradc, LRADC_CTRL1_TOUCH_DETECT_IRQ_EN, LRADC_CTRL1);
 }

I am confused. Why don't you send this like a normal patch?

regards,
dan carpenter

#36 lore raw

PATCH v6 1/1 staging/iio/adc: change the MXS touchscreen driver implementation

Hi Dan,

Quoted 15 lines · On Monday 24 February 2014 14:33:16 Dan Carpenter wrote:
Quoted 14 lines · Juergen Beisert
Quoted 2 lines

While I don't have much experience with the TS part of the code but I can investigate if you don't have any idea.

can you please test the following patch?
After releasing the touchscreen the internal state machine was left in a wrong state.

drivers/staging/iio/adc/mxs-lradc.c +0 -0
index e2dd783..558a76c 100644
@@ -698,6 +698,7 @@ static void mxs_lradc_finish_touch_event(struct
 mxs_lradc *lradc, bool valid) }
 
Quoted 7 lines

drivers/staging/iio/adc/mxs-lradc.c static void mxs_lradc_finish_touch_event(struct mxs_lradc *lradc, bool valid) · line 704

Quoted 5 lines
drivers/staging/iio/adc/mxs-lradc.c +1 -0
        /* if it is released, wait for the next touch via IRQ */
+       lradc->cur_plate = LRADC_TOUCH;
        mxs_lradc_reg_clear(lradc, LRADC_CTRL1_TOUCH_DETECT_IRQ, LRADC_CTRL1);
        mxs_lradc_reg_set(lradc, LRADC_CTRL1_TOUCH_DETECT_IRQ_EN, LRADC_CTRL1);
        } 

I am confused. Why don't you send this like a normal patch?

For testing fist. But you are right, patch will follow.

Regards,
Juergen

Signature · 2 lines
Pengutronix e.K.                              | Juergen Beisert             |
Linux Solutions for Science and Industry      | http://www.pengutronix.de/  |
#37 lore raw

PATCH v6 1/1 staging/iio/adc: change the MXS touchscreen driver implementation

Quoted 26 lines · Juergen Beisert

Hi Dan,

Quoted 15 lines · On Monday 24 February 2014 14:33:16 Dan Carpenter wrote:
Quoted 14 lines · Juergen Beisert
Quoted 2 lines

While I don't have much experience with the TS part of the code but I can investigate if you don't have any idea.

can you please test the following patch?
After releasing the touchscreen the internal state machine was left in a wrong state.

drivers/staging/iio/adc/mxs-lradc.c +0 -0
index e2dd783..558a76c 100644
@@ -698,6 +698,7 @@ static void mxs_lradc_finish_touch_event(struct
 mxs_lradc *lradc, bool valid) }
 
Quoted 7 lines

drivers/staging/iio/adc/mxs-lradc.c static void mxs_lradc_finish_touch_event(struct mxs_lradc *lradc, bool valid) · line 704

Quoted 5 lines
drivers/staging/iio/adc/mxs-lradc.c +1 -0
        /* if it is released, wait for the next touch via IRQ */
+       lradc->cur_plate = LRADC_TOUCH;
        mxs_lradc_reg_clear(lradc, LRADC_CTRL1_TOUCH_DETECT_IRQ, LRADC_CTRL1);
        mxs_lradc_reg_set(lradc, LRADC_CTRL1_TOUCH_DETECT_IRQ_EN, LRADC_CTRL1);
        } 

I am confused. Why don't you send this like a normal patch?

Quoted 2 lines

For testing fist. But you are right, patch will follow.

Never mind, I suck at reading.

regards,
dan carpenter

#38 lore raw

PATCH 1/1 staging/iio/adc/MXS/LRADC: fix touchscreen statemachine

In reply to Dan Carpenter

Releasing the touchscreen lets the internal statemachine left in a wrong state. Due to this the release coordinate will be reported again by accident when the next touchscreen event happens. This change sets up the correct state when waiting for the next touchscreen event.

drivers/staging/iio/adc/mxs-lradc.c +1 -0
index 7fc66a6..514844e 100644
@@ -757,6 +757,7 @@ static void mxs_lradc_finish_touch_event(struct mxs_lradc *lradc, bool valid)
 	}
 
 	/* if it is released, wait for the next touch via IRQ */
+	lradc->cur_plate = LRADC_TOUCH;
 	mxs_lradc_reg_clear(lradc, LRADC_CTRL1_TOUCH_DETECT_IRQ, LRADC_CTRL1);
 	mxs_lradc_reg_set(lradc, LRADC_CTRL1_TOUCH_DETECT_IRQ_EN, LRADC_CTRL1);
 }
Signature · 2 lines
Pengutronix e.K.                              | Juergen Beisert             |
Linux Solutions for Science and Industry      | http://www.pengutronix.de/  |
#39 lore raw

PATCH 1/1 staging/iio/adc/MXS/LRADC: fix touchscreen statemachine

Quoted 7 lines · Juergen Beisert

Releasing the touchscreen lets the internal statemachine left in a wrong state. Due to this the release coordinate will be reported again by accident when the next touchscreen event happens. This change sets up the correct state when waiting for the next touchscreen event.

Quoted 16 lines
drivers/staging/iio/adc/mxs-lradc.c +1 -0
index 7fc66a6..514844e 100644
@@ -757,6 +757,7 @@ static void mxs_lradc_finish_touch_event(struct mxs_lradc *lradc, bool valid)
 	}
 
 	/* if it is released, wait for the next touch via IRQ */
+	lradc->cur_plate = LRADC_TOUCH;
 	mxs_lradc_reg_clear(lradc, LRADC_CTRL1_TOUCH_DETECT_IRQ, LRADC_CTRL1);
 	mxs_lradc_reg_set(lradc, LRADC_CTRL1_TOUCH_DETECT_IRQ_EN, LRADC_CTRL1);
 }
Signature · 3 lines
-- 
Pengutronix e.K. ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?| Juergen Beisert ? ? ? ? ? ? |
Linux Solutions for Science and Industry ? ? ?| http://www.pengutronix.de/  |
Signature · 3 lines
Alexandre Belloni, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
maintainer Applied
#40 lore raw

PATCH 1/1 staging/iio/adc/MXS/LRADC: fix touchscreen statemachine

Quoted 10 lines · Alexandre Belloni
Quoted 7 lines · Juergen Beisert

Releasing the touchscreen lets the internal statemachine left in a wrong state. Due to this the release coordinate will be reported again by accident when the next touchscreen event happens. This change sets up the correct state when waiting for the next touchscreen event.

Applied to the fixes-togreg branch of iio.git Thanks

Jonathan

Quoted 18 lines
Quoted 17 lines
drivers/staging/iio/adc/mxs-lradc.c +1 -1
index 7fc66a6..514844e 100644
@@ -757,6 +757,7 @@ static void mxs_lradc_finish_touch_event(struct mxs_lradc *lradc, bool valid)
  	}
 
  	/* if it is released, wait for the next touch via IRQ */
+	lradc->cur_plate = LRADC_TOUCH;
  	mxs_lradc_reg_clear(lradc, LRADC_CTRL1_TOUCH_DETECT_IRQ, LRADC_CTRL1);
  	mxs_lradc_reg_set(lradc, LRADC_CTRL1_TOUCH_DETECT_IRQ_EN, LRADC_CTRL1);
  }
 
--
Pengutronix e.K.                              | Juergen Beisert             |
Linux Solutions for Science and Industry      | http://www.pengutronix.de/  |
maintainer
#41 lore raw

PATCH 1/1 staging/iio/adc/MXS/LRADC: fix touchscreen statemachine

Quoted 7 lines · Jonathan Cameron
Quoted 6 lines · Alexandre Belloni
Quoted 5 lines · Juergen Beisert

Releasing the touchscreen lets the internal statemachine left in a wrong state. Due to this the release coordinate will be reported again by accident when the next touchscreen event happens. This change sets up the correct state when waiting for the next touchscreen event.

Quoted 5 lines
Quoted 4 lines
Quoted 2 lines

Applied to the fixes-togreg branch of iio.git Thanks

I just forced an update to the tree having realised that I'd not marked it for stable (the change went into the 3.13 tree) and that a few more details were needed to explain the effects of the problem and where it came from. Will let it sit overnight then send on to Greg sometime in the next few days. Good to have this one cleared up.

Jonathan

Quoted 25 lines

Jonathan

Quoted 14 lines
Quoted 14 lines
drivers/staging/iio/adc/mxs-lradc.c +1 -0
index 7fc66a6..514844e 100644
@@ -757,6 +757,7 @@ static void mxs_lradc_finish_touch_event(struct mxs_lradc *lradc, bool valid)
      }
 
      /* if it is released, wait for the next touch via IRQ */
+    lradc->cur_plate = LRADC_TOUCH;
      mxs_lradc_reg_clear(lradc, LRADC_CTRL1_TOUCH_DETECT_IRQ, LRADC_CTRL1);
      mxs_lradc_reg_set(lradc, LRADC_CTRL1_TOUCH_DETECT_IRQ_EN, LRADC_CTRL1);
  }
Quoted 4 lines
Quoted 3 lines

--

Pengutronix e.K.                              | Juergen Beisert             |
Linux Solutions for Science and Industry      | http://www.pengutronix.de/  |

--
To unsubscribe from this list: send the line "unsubscribe linux-iio" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html

#42 lore raw

PATCH v6 1/1 staging/iio/adc: change the MXS touchscreen driver implementation

In reply to Juergen Beisert

Hi Juergen,

Quoted 9 lines · Juergen Beisert

Hi Alexandre,

Quoted 2 lines

While I don't have much experience with the TS part of the code but I can investigate if you don't have any idea.

can you please test the following patch?
After releasing the touchscreen the internal state machine was left in a wrong state.

This seems to solve the issue. You can send the patch with my Tested-by.

It is probably worth trying to get it in 3.14.

Thanks !

Quoted 21 lines
drivers/staging/iio/adc/mxs-lradc.c +1 -0
index e2dd783..558a76c 100644
@@ -698,6 +698,7 @@ static void mxs_lradc_finish_touch_event(struct mxs_lradc *lradc, bool valid)
        }
 
        /* if it is released, wait for the next touch via IRQ */
+       lradc->cur_plate = LRADC_TOUCH;
        mxs_lradc_reg_clear(lradc, LRADC_CTRL1_TOUCH_DETECT_IRQ, LRADC_CTRL1);
        mxs_lradc_reg_set(lradc, LRADC_CTRL1_TOUCH_DETECT_IRQ_EN, LRADC_CTRL1);
 }

Regards,
Juergen

Signature · 4 lines
Pengutronix e.K. ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?| Juergen Beisert ? ? ? ? ? ? |
Linux Solutions for Science and Industry ? ? ?| Phone: +49-5121-206917-5128 |
Peiner Str. 6-8, 31137 Hildesheim, Germany ? ?| Fax: ? +49-5121-206917-5555 |
Amtsgericht Hildesheim, HRA 2686 ? ? ? ? ? ? ?| http://www.pengutronix.de/ ?|
Signature · 3 lines
Alexandre Belloni, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
maintainer
#43 lore raw

PATCH v6 1/1 staging/iio/adc: change the MXS touchscreen driver implementation

Quoted 11 lines · Alexandre Belloni

Hi Juergen,

Quoted 3 lines · Juergen Beisert

Hi Alexandre,

Quoted 1 line

While I don't have much experience with the TS part of the code but

I

Quoted 4 lines
Quoted 1 line

can investigate if you don't have any idea.

can you please test the following patch?
After releasing the touchscreen the internal state machine was left

Quoted 8 lines

in a

Quoted 2 lines

wrong state.

This seems to solve the issue. You can send the patch with my Tested-by.

It is probably worth trying to get it in 3.14.

Definitely. There is time.

Quoted 32 lines

Thanks !

Review

Quoted 1 line
(quoted diff) +0 -0

b/drivers/staging/iio/adc/mxs-lradc.c

drivers/staging/iio/adc/mxs-lradc.c static void mxs_lradc_finish_touch_event(struct

Quoted 4 lines

index e2dd783..558a76c 100644

drivers/staging/iio/adc/mxs-lradc.c +0 -0
@@ -698,6 +698,7 @@ static void mxs_lradc_finish_touch_event(struct

mxs_lradc *lradc, bool valid)

drivers/staging/iio/adc/mxs-lradc.c static void mxs_lradc_finish_touch_event(struct mxs_lradc *lradc, bool valid)

Quoted 5 lines
drivers/staging/iio/adc/mxs-lradc.c +1 -0
        }
 
        /* if it is released, wait for the next touch via IRQ */
+       lradc->cur_plate = LRADC_TOUCH;
        mxs_lradc_reg_clear(lradc, LRADC_CTRL1_TOUCH_DETECT_IRQ,

LRADC_CTRL1);

drivers/staging/iio/adc/mxs-lradc.c static void mxs_lradc_finish_touch_event(struct · line 703

Quoted 1 line
drivers/staging/iio/adc/mxs-lradc.c +0 -0
        mxs_lradc_reg_set(lradc, LRADC_CTRL1_TOUCH_DETECT_IRQ_EN,

LRADC_CTRL1);

Quoted 7 lines
drivers/staging/iio/adc/mxs-lradc.c +0 -0
 }

Regards,
Juergen

Signature · 1 line
Pengutronix e.K. ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?| Juergen Beisert ? ? ?

? ? ? |

Quoted 1 line

Linux Solutions for Science and Industry ? ? ?| Phone:

+49-5121-206917-5128 |

Quoted 1 line

Peiner Str. 6-8, 31137 Hildesheim, Germany ? ?| Fax: ?

+49-5121-206917-5555 |

Quoted 1 line

Amtsgericht Hildesheim, HRA 2686 ? ? ? ? ? ? ?|

http://www.pengutronix.de/ ?|

Signature · 1 line
Sent from my Android phone with K-9 Mail. Please excuse my brevity.