Skip to contentSkip to conversation

arm: dts: am33xx.dtsi: Add node name to rtc device node

PATCH New Stefan Roese 3 participants 5 messages Feb 5, 2014 – Feb 28, 2014 Device tree bindings

lore
Share & tools
lore
#0 lore raw

PATCH 1/3 arm: dts: am33xx.dtsi: Add node name to rtc device node

Making it possible to reference and therefor change (disable) this device node from other dts file which import this dtsi file.

Cc Lukas Stockmann <[email protected]>
Cc Benoit Cousson <[email protected]>
Cc Tony Lindgren <[email protected]>
---
 arch/arm/boot/dts/am33xx.dtsi | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
arch/arm/boot/dts/am33xx.dtsi +1 -1
index 6d95d3d..b8daf8c 100644
@@ -399,7 +399,7 @@
 			ti,timer-pwm;
 		};
 
-		rtc@44e3e000 {
+		rtc: rtc@44e3e000 {
 			compatible = "ti,da830-rtc";
 			reg = <0x44e3e000 0x1000>;
 			interrupts = <75
Signature · 1 line
1.8.5.3
#1 lore raw

PATCH 2/3 arm: dts: Add Siemens Draco SOM dtsi

This patch adds support for the Siemens Draco SOM (System On Module) which is used by multiple Siemens boards. Support for one is posted in this series as well, the dxr2-e.

This SOM is based on the TI AM3352 with the following configuration:

- CPU: AM3352BZCEA30
- RAM: 128MB DDR3@303MHz
- NAND FLASH: 256MB
- RTC: disabled via hw wiring (registers not available!)

Cc Lukas Stockmann <[email protected]>
Cc Benoit Cousson <[email protected]>
Cc Tony Lindgren <[email protected]>
---
 arch/arm/boot/dts/am335x-draco.dtsi | 163 ++++++++++++++++++++++++++++++++++++
 1 file changed, 163 insertions(+)
 create mode 100644 arch/arm/boot/dts/am335x-draco.dtsi
arch/arm/boot/dts/am335x-draco.dtsi new file +163 -0
new file mode 100644
index 0000000..88b414a
@@ -0,0 +1,163 @@
+/*
+ * Common support for Siemens Draco SOM (AM335x based)
+ *
+ * Copyright (C) 2013,2014 - Stefan Roese <[email protected]>
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2.  This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ */
+
+/ {
+	memory {
+		device_type = "memory";
+		reg = <0x80000000 0x08000000>; /* 128 MB */
+	};
+
+	am33xx_pinmux: pinmux@44e10800 {
+		i2c0_pins: pinmux_i2c0_pins {
+			pinctrl-single,pins = <
+				0x188 (PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c0_sda.i2c0_sda */
+				0x18c (PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c0_scl.i2c0_scl */
+			>;
+		};
+
+		uart0_pins: pinmux_uart0_pins {
+			pinctrl-single,pins = <
+				0x170 (PIN_INPUT_PULLUP | MUX_MODE0)	/* uart0_rxd.uart0_rxd */
+				0x174 (PIN_OUTPUT_PULLDOWN | MUX_MODE0)	/* uart0_txd.uart0_txd */
+			>;
+		};
+
+		nandflash_pins: nandflash_pins {
+			pinctrl-single,pins = <
+				0x0 (PIN_INPUT_PULLUP | MUX_MODE0)	/* gpmc_ad0.gpmc_ad0 */
+				0x4 (PIN_INPUT_PULLUP | MUX_MODE0)	/* gpmc_ad1.gpmc_ad1 */
+				0x8 (PIN_INPUT_PULLUP | MUX_MODE0)	/* gpmc_ad2.gpmc_ad2 */
+				0xc (PIN_INPUT_PULLUP | MUX_MODE0)	/* gpmc_ad3.gpmc_ad3 */
+				0x10 (PIN_INPUT_PULLUP | MUX_MODE0)	/* gpmc_ad4.gpmc_ad4 */
+				0x14 (PIN_INPUT_PULLUP | MUX_MODE0)	/* gpmc_ad5.gpmc_ad5 */
+				0x18 (PIN_INPUT_PULLUP | MUX_MODE0)	/* gpmc_ad6.gpmc_ad6 */
+				0x1c (PIN_INPUT_PULLUP | MUX_MODE0)	/* gpmc_ad7.gpmc_ad7 */
+				0x70 (PIN_INPUT_PULLUP | MUX_MODE0)	/* gpmc_wait0.gpmc_wait0 */
+				0x74 (PIN_INPUT_PULLUP | MUX_MODE7)	/* gpmc_wpn.gpio0_30 */
+				0x7c (PIN_OUTPUT | MUX_MODE0)		/* gpmc_csn0.gpmc_csn0  */
+				0x90 (PIN_OUTPUT | MUX_MODE0)		/* gpmc_advn_ale.gpmc_advn_ale */
+				0x94 (PIN_OUTPUT | MUX_MODE0)		/* gpmc_oen_ren.gpmc_oen_ren */
+				0x98 (PIN_OUTPUT | MUX_MODE0)		/* gpmc_wen.gpmc_wen */
+				0x9c (PIN_OUTPUT | MUX_MODE0)		/* gpmc_be0n_cle.gpmc_be0n_cle */
+			>;
+		};
+	};
+
+	ocp {
+		uart0: serial@44e09000 {
+			pinctrl-names = "default";
+			pinctrl-0 = <&uart0_pins>;
+			status = "okay";
+		};
+
+		i2c0: i2c@44e0b000 {
+			pinctrl-names = "default";
+			pinctrl-0 = <&i2c0_pins>;
+
+			status = "okay";
+			clock-frequency = <400000>;
+
+			eeprom: eeprom@50 {
+				compatible = "atmel,24c128";
+				reg = <0x50>;
+				pagesize = <64>;
+			};
+		};
+
+		musb: usb@47400000 {
+			status = "okay";
+
+			control@44e10000 {
+				status = "okay";
+			};
+
+			usb-phy@47401300 {
+				status = "okay";
+			};
+
+			usb-phy@47401b00 {
+				status = "okay";
+			};
+
+			usb@47401000 {
+				status = "okay";
+			};
+
+			usb@47401800 {
+				status = "okay";
+				dr_mode = "host";
+			};
+
+			dma-controller@07402000  {
+				status = "okay";
+			};
+		};
+	};
+};
+
+&timer3 {
+	status = "disabled";
+};
+
+&uart4 {
+	status = "disabled";
+};
+
+&elm {
+	status = "okay";
+};
+
+&gpmc {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&nandflash_pins>;
+
+	ranges = <0 0 0x08000000 0x10000000>;	/* CS0: NAND */
+
+	nand@0,0 {
+		reg = <0 0 0>; /* CS0, offset 0 */
+		nand-bus-width = <8>;
+		ti,nand-ecc-opt = "bch8";
+		gpmc,device-nand = "true";
+		gpmc,device-width = <1>;
+		gpmc,sync-clk-ps = <0>;
+		gpmc,cs-on-ns = <0>;
+		gpmc,cs-rd-off-ns = <44>;
+		gpmc,cs-wr-off-ns = <44>;
+		gpmc,adv-on-ns = <6>;
+		gpmc,adv-rd-off-ns = <34>;
+		gpmc,adv-wr-off-ns = <44>;
+		gpmc,we-on-ns = <0>;
+		gpmc,we-off-ns = <40>;
+		gpmc,oe-on-ns = <0>;
+		gpmc,oe-off-ns = <54>;
+		gpmc,access-ns = <64>;
+		gpmc,rd-cycle-ns = <82>;
+		gpmc,wr-cycle-ns = <82>;
+		gpmc,wait-on-read = "true";
+		gpmc,wait-on-write = "true";
+		gpmc,bus-turnaround-ns = <0>;
+		gpmc,cycle2cycle-delay-ns = <0>;
+		gpmc,clk-activation-ns = <0>;
+		gpmc,wait-monitoring-ns = <0>;
+		gpmc,wr-access-ns = <40>;
+		gpmc,wr-data-mux-bus-ns = <0>;
+
+		#address-cells = <1>;
+		#size-cells = <1>;
+		elm_id = <&elm>;
+	};
+};
+
+/* disable the RTC node as its not accessible on the draco/dxr2 board */
+&rtc {
+	status = "disabled";
+	ti,hwmods = "disabled";
+};
Signature · 1 line
1.8.5.3
#2 lore raw

PATCH 3/3 arm: dts: Add Siemens am335x-dxr2-e.dts

In reply to Stefan Roese

Add support for the Siemens DXR2 board. The DXR2-E is the first one that is pushed now. It uses the Draco SOM and therefor includes this dtsi file for the common device nodes.

Cc Lukas Stockmann <[email protected]>
Cc Benoit Cousson <[email protected]>
Cc Tony Lindgren <[email protected]>
---
 arch/arm/boot/dts/am335x-dxr2-e.dts | 242 ++++++++++++++++++++++++++++++++++++
 1 file changed, 242 insertions(+)
 create mode 100644 arch/arm/boot/dts/am335x-dxr2-e.dts
arch/arm/boot/dts/am335x-dxr2-e.dts new file +242 -0
new file mode 100644
index 0000000..5fef637
@@ -0,0 +1,242 @@
+/*
+ * Support for Siemens DXR2.E board
+ *
+ * Copyright (C) 2013,2014 - Stefan Roese <[email protected]>
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2.  This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ */
+
+/dts-v1/;
+
+#include "am33xx.dtsi"
+#include "am335x-draco.dtsi"
+#include <dt-bindings/pwm/pwm.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "Siemens DXR2.E";
+	compatible = "siemens,dxr2", "ti,am33xx";
+
+	/* ethernet alias is needed for the MAC address passing from U-Boot */
+	aliases {
+		ethernet0 = &cpsw_emac0;
+		mdio-gpio0 = &mdio0;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		button0 {
+			label = "button0";
+			gpios = <&gpio0 27 0>;
+			linux,code = <KEY_F1>; /* button0 */
+		};
+	};
+
+	am33xx_pinmux: pinmux at 44e10800 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_mux_pins>;
+
+		gpio_mux_pins: gpio_mux_pins {
+			pinctrl-single,pins = <
+				0x020 (PIN_OUTPUT | MUX_MODE4)	/* GPMC_AD8, sinus inverter */
+				0x024 (PIN_OUTPUT | MUX_MODE4)	/* GPMC_AD9, sinus inverter */
+				0x028 (PIN_INPUT | MUX_MODE4)	/* GPMC_AD10, sinus inverter */
+				0x02c (PIN_INPUT | MUX_MODE7)	/* GPMC_AD11, button */
+				0x030 (PIN_OUTPUT | MUX_MODE7)	/* GPMC_AD12, UI */
+				0x034 (PIN_OUTPUT | MUX_MODE7)	/* GPMC_AD13, UI */
+				0x038 (PIN_OUTPUT | MUX_MODE7)	/* conf_gpmc_ad14, relay0 */
+				0x03c (PIN_OUTPUT | MUX_MODE7)	/* GPMC_AD15, UI */
+				0x08c (PIN_OUTPUT | MUX_MODE7)	/* GPMC_CLK, UI */
+				0x0d4 (PIN_OUTPUT | MUX_MODE7)	/* LCD_DATA13, AO_EN */
+				0x0dc (PIN_OUTPUT | MUX_MODE7)	/* LCD_DATA15, UI */
+				0x0ec (PIN_INPUT | MUX_MODE7)	/* LCD_AC_BIAS_EN, PWfail */
+				0x0f0 (PIN_OUTPUT | MUX_MODE7)	/* MMC0_DAT3, UI */
+				0x0f4 (PIN_OUTPUT | MUX_MODE7)	/* MMC0_DAT2, UI */
+				0x0f8 (PIN_OUTPUT | MUX_MODE7)	/* MMC0_DAT1, UI */
+				0x0fc (PIN_OUTPUT | MUX_MODE7)	/* MMC0_DAT0, UI */
+				0x108 (PIN_OUTPUT | MUX_MODE7)	/* MII1_COL, relay1 */
+				0x100 (PIN_OUTPUT | MUX_MODE7)	/* MMC0_CLK, UI */
+				0x118 (PIN_INPUT_PULLDOWN | MUX_MODE7)	/* MII1_RX_DV.gpio3.4, di0 */
+				0x120 (PIN_INPUT_PULLDOWN | MUX_MODE7)	/* MII1_TXD2.gpio0.17, di1 */
+				0x12c (PIN_OUTPUT | MUX_MODE1)	/* MII1_TXCLK, MSTP RX2 */
+				0x164 (PIN_OUTPUT | MUX_MODE7)	/* ECAP0_IN_PWM0_OUT, relay2 */
+				0x168 (PIN_INPUT | MUX_MODE1)	/* MII1_RXCLK, tpuart RX4 */
+				0x16c (PIN_OUTPUT | MUX_MODE1)	/* LCD_DATA9, tpuart TX4 */
+				0x178 (PIN_OUTPUT | MUX_MODE7)	/* UART1_CTS, UI */
+				0x1b0 (PIN_OUTPUT | MUX_MODE7)	/* XDMA_EVENT_INTR0, KNX Power */
+				0x1d0 (PIN_INPUT | MUX_MODE0)	/* tms jtag */
+				0x1d4 (PIN_INPUT | MUX_MODE0)	/* tdi jtag */
+				0x1d8 (PIN_OUTPUT | MUX_MODE0)	/* tdo jtag */
+				0x1dc (PIN_INPUT | MUX_MODE0)	/* tck jtag */
+				0x1e0 (PIN_INPUT | MUX_MODE0)	/* trstn jtag */
+			>;
+		};
+
+		user_leds_s0: user_leds_s0 {
+			pinctrl-single,pins = <
+				0x88 (PIN_INPUT | MUX_MODE7)	/* gpmc_csn3.gpio2_0 */
+				0x1e4 (PIN_INPUT | MUX_MODE7)	/* emu0.gpio3_7 */
+			>;
+		};
+
+		epwmss0_pins: epwmss0_pins {
+			pinctrl-single,pins = <
+				0x150 (PIN_OUTPUT | MUX_MODE3)	/* conf_spi0_sclk.ehrpwm0A */
+				0x154 (PIN_OUTPUT | MUX_MODE3)	/* conf_spi0_d0.ehrpwm0B */
+			>;
+		};
+
+		epwmss1_pins: epwmss1_pins {
+			pinctrl-single,pins = <
+				0x0c8 (PIN_OUTPUT | MUX_MODE2)	/* lcd_data10.lcd_data10 */
+				0x0cc (PIN_OUTPUT | MUX_MODE2)	/* lcd_data11.lcd_data11 */
+			>;
+		};
+
+		ecap1_pins: ecap1_pins {
+			pinctrl-single,pins = <
+				0x160 (PIN_OUTPUT | MUX_MODE2)	/* conf_spi0_cs1*/
+			>;
+		};
+
+		cpsw_default: cpsw_default {
+			pinctrl-single,pins = <
+				0x10c (PIN_INPUT_PULLDOWN | MUX_MODE1)	/* mii1_crs.rmii1_crs_dv */
+				0x114 (PIN_OUTPUT | MUX_MODE1)		/* mii1_txen.mii1_txen */
+				0x124 (PIN_OUTPUT | MUX_MODE1)		/* mii1_txd1.mii1_txd1 */
+				0x128 (PIN_OUTPUT | MUX_MODE1)		/* mii1_txd0.mii1_txd0 */
+				0x13c (PIN_INPUT_PULLDOWN | MUX_MODE1)	/* mii1_rxd1.mii1_rxd1 */
+				0x140 (PIN_INPUT_PULLDOWN | MUX_MODE1)	/* mii1_rxd0.mii1_rxd0 */
+				0x144 (PIN_INPUT_PULLDOWN | MUX_MODE0)	/* rmii1_refclk.rmii1_refclk */
+			>;
+		};
+
+		cpsw_sleep: cpsw_sleep {
+			pinctrl-single,pins = <
+				0x10c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+				0x114 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+				0x124 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+				0x128 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+				0x13c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+				0x140 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+				0x144 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			>;
+		};
+
+		davinci_mdio_default: davinci_mdio_default {
+			pinctrl-single,pins = <
+				/* MDIO */
+				0x148 (PIN_INPUT | SLEWCTRL_FAST | MUX_MODE0)	/* mdio_data.mdio_data */
+				0x14c (PIN_OUTPUT | MUX_MODE0)			/* mdio_clk.mdio_clk */
+			>;
+		};
+
+		davinci_mdio_sleep: davinci_mdio_sleep {
+			pinctrl-single,pins = <
+				/* MDIO reset value */
+				0x148 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+				0x14c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			>;
+		};
+
+		gpio_mdio_default: gpio_mdio_default {
+			pinctrl-single,pins = <
+				/* MDIO via GPIO */
+				0x148 (PIN_INPUT | MUX_MODE7)	/* mdio_data.mdio_data GPIO0_0 */
+				0x14c (PIN_OUTPUT | MUX_MODE7)	/* mdio_clk.mdio_clk GPIO0_1 */
+			>;
+		};
+	};
+
+	ocp {
+		epwmss0: epwmss at 48300000 {
+			status = "okay";
+			compatible = "ti,am33xx-pwmss";
+
+			ehrpwm0: ehrpwm at 48300200 {
+				compatible = "ti,am33xx-ehrpwm";
+				status = "okay";
+				pinctrl-names = "default";
+				pinctrl-0 = <&epwmss0_pins>;
+			};
+		};
+
+		epwmss1: epwmss at 48302000 {
+			status = "okay";
+			compatible = "ti,am33xx-pwmss";
+
+			ecap1: ecap at 48302100 {
+				compatible = "ti,am33xx-ecap";
+				status = "okay";
+				pinctrl-names = "default";
+				pinctrl-0 = <&ecap1_pins>;
+			};
+
+			ehrpwm1: ehrpwm at 48302200 {
+				compatible = "ti,am33xx-ehrpwm";
+				status = "okay";
+				pinctrl-names = "default";
+				pinctrl-0 = <&epwmss1_pins>;
+			};
+		};
+	};
+
+	leds {
+		pinctrl-names = "default";
+		pinctrl-0 = <&user_leds_s0>;
+		compatible = "gpio-leds";
+
+		led at 0 {
+			label = "led0";
+			gpios = <&gpio2 0 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+
+		led at 1 {
+			label = "led1";
+			gpios = <&gpio3 7 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+	};
+};
+
+&mac {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&cpsw_default>;
+	pinctrl-1 = <&cpsw_sleep>;
+	slaves = <1>;			/* use only one emac if */
+
+	mdio0: gpio {
+		compatible = "virtual,mdio-gpio";
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_mdio_default>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+		gpios = <&gpio0 1 GPIO_ACTIVE_HIGH	/* MDIO-CLK */
+			 &gpio0 0 GPIO_ACTIVE_HIGH>;	/* MDIO-DATA */
+
+		phy0: ethernet-phy at 1 {
+			reg = <0>;
+		};
+	};
+};
+
+/* Disable davinci/am335x mdio interface on this platform */
+&davinci_mdio {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&davinci_mdio_default>;
+	pinctrl-1 = <&davinci_mdio_sleep>;
+	status = "disabled";
+};
+
+&cpsw_emac0 {
+	phy_id = <&mdio0>, <0>;
+	phy-mode = "rmii";
+};
+
+&phy_sel {
+	rmii-clock-ext;
+};
Signature · 1 line
1.8.5.3
#3 lore raw

PATCH 1/3 arm: dts: am33xx.dtsi: Add node name to rtc device node

In reply to Stefan Roese

Hello.

Quoted 16 lines · Stefan Roese

Making it possible to reference and therefor change (disable) this device node from other dts file which import this dtsi file.

Cc Lukas Stockmann <[email protected]>
Cc Benoit Cousson <[email protected]>
Cc Tony Lindgren <[email protected]>
---
  arch/arm/boot/dts/am33xx.dtsi | 2 +-
  1 file changed, 1 insertion(+), 1 deletion(-)
arch/arm/boot/dts/am33xx.dtsi +0 -0
index 6d95d3d..b8daf8c 100644

arch/arm/boot/dts/am33xx.dtsi line 402

Quoted 5 lines
arch/arm/boot/dts/am33xx.dtsi +1 -1
@@ -399,7 +399,7 @@
  			ti,timer-pwm;
  		};
 
-		rtc@44e3e000 {
+		rtc: rtc@44e3e000 {

Node name is "rtc@44e3e000" -- what you are adding is a label.

WBR, Sergei

#4 lore raw

PATCH 1/3 arm: dts: am33xx.dtsi: Add node name to rtc device node

In reply to Stefan Roese
Quoted 7 lines · Stefan Roese

Making it possible to reference and therefor change (disable) this device node from other dts file which import this dtsi file.

Cc Lukas Stockmann <[email protected]>
Cc Benoit Cousson <[email protected]>
Cc Tony Lindgren <[email protected]>

Thanks applying into omap-for-v3.15/dt.

Tony

Quoted 20 lines
---
 arch/arm/boot/dts/am33xx.dtsi | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
arch/arm/boot/dts/am33xx.dtsi +1 -1
index 6d95d3d..b8daf8c 100644
@@ -399,7 +399,7 @@
 			ti,timer-pwm;
 		};
 
-		rtc at 44e3e000 {
+		rtc: rtc at 44e3e000 {
 			compatible = "ti,da830-rtc";
 			reg = <0x44e3e000 0x1000>;
 			interrupts = <75
Signature · 1 line
1.8.5.3