ata: ahci_st: Provide DT bindings for ST's SATA implementation
Subsystems (3)
PATCH v2 1/3 ata: ahci_st: Provide DT bindings for ST's SATA implementation
--- Documentation/devicetree/bindings/ata/ahci-st.txt | 31 +++++++++++++++++++++++ 1 file changed, 31 insertions(+) create mode 100644 Documentation/devicetree/bindings/ata/ahci-st.txt
Documentation/devicetree/bindings/ata/ahci-st.txt new file +31 -0
@@ -0,0 +1,31 @@ +STMicroelectronics STi SATA controller + +This binding describes a SATA device. + +Required properties: + - compatible : Must be "st,ahci" + - reg : Physical base addresses and length of register sets + - interrupts : Interrupt associated with the SATA device + - interrupt-names : Associated name must be; "hostc" + - resets : The power-down and soft-reset lines of SATA IP + - reset-names : Associated names must be; "pwr-dwn" and "sw-rst" + - clocks : The phandle for the clock + - clock-names : Associated name must be; "ahci_clk" + - phys : The phandle for the PHY device + - phy-names : Associated name must be; "ahci_phy" + +Example: + + sata0: sata at fe380000 { + compatible = "st,ahci"; + reg = <0xfe380000 0x1000>; + interrupts = <GIC_SPI 157 IRQ_TYPE_NONE>; + interrupt-names = "hostc"; + phys = <&miphy365x_phy MIPHY_PORT_0 MIPHY_TYPE_SATA>; + phy-names = "ahci_phy"; + resets = <&powerdown STIH416_SATA0_POWERDOWN>, + <&softreset STIH416_SATA0_SOFTRESET>; + reset-names = "pwr-dwn", "sw-rst"; + clocks = <&CLK_S_ICN_REG_0>; + clock-names = "ahci_clk"; + };
Signature · 1 line
1.8.3.2
PATCH v2 2/3 ARM: DT: STi: Add DT node for ST's SATA device
--- arch/arm/boot/dts/stih416-b2020-revE.dts | 4 ++++ arch/arm/boot/dts/stih416-b2020.dts | 4 ++++ arch/arm/boot/dts/stih416.dtsi | 16 ++++++++++++++++ 3 files changed, 24 insertions(+)
arch/arm/boot/dts/stih416-b2020-revE.dts +4 -0
@@ -37,5 +37,9 @@ st,pcie-tx-pol-inv; st,sata-gen = <3>; }; + + sata0: sata at fe380000{ + status = "okay"; + }; }; };
arch/arm/boot/dts/stih416-b2020.dts +4 -0
@@ -18,5 +18,9 @@ st,pcie_tx_pol_inv = <1>; st,sata_gen = "gen3"; }; + + sata0: sata at fe380000{ + status = "okay"; + }; }; };
arch/arm/boot/dts/stih416.dtsi +16 -0
@@ -205,5 +205,21 @@ #phy-cells = <2>; st,syscfg = <&syscfg_rear>; }; + + sata0: sata at fe380000 { + compatible = "st,ahci"; + reg = <0xfe380000 0x1000>; + interrupts = <GIC_SPI 157 IRQ_TYPE_NONE>; + interrupt-names = "hostc"; + phys = <&miphy365x_phy MIPHY_PORT_0 MIPHY_TYPE_SATA>; + phy-names = "sata-phy"; + resets = <&powerdown STIH416_SATA0_POWERDOWN>, + <&softreset STIH416_SATA0_SOFTRESET>; + reset-names = "pwr-dwn", "sw-rst"; + clock-names = "ahci_clk"; + clocks = <&CLK_S_ICN_REG_0>; + + status = "disabled"; + }; }; };
Signature · 1 line
1.8.3.2
PATCH v2 3/3 ahci: st: Add support for ST's SATA IP
In reply to Lee Jones--- drivers/ata/Kconfig | 9 ++ drivers/ata/Makefile | 1 + drivers/ata/ahci_st.c | 250 ++++++++++++++++++++++++++++++++++++++++++++++++++ 3 files changed, 260 insertions(+) create mode 100644 drivers/ata/ahci_st.c
drivers/ata/Kconfig +9 -0
@@ -98,6 +98,15 @@ config SATA_AHCI_PLATFORM If unsure, say N. +config SATA_AHCI_ST + tristate "ST SATA support" + depends on SATA_AHCI_PLATFORM + select GENERIC_PHY + help + This option enables support for ST SATA controller. + + If unsure, say N. + config AHCI_IMX tristate "Freescale i.MX AHCI SATA support" depends on SATA_AHCI_PLATFORM && MFD_SYSCON
drivers/ata/Makefile +1 -0
@@ -5,6 +5,7 @@ obj-$(CONFIG_ATA) += libata.o obj-$(CONFIG_SATA_AHCI) += ahci.o libahci.o obj-$(CONFIG_SATA_ACARD_AHCI) += acard-ahci.o libahci.o obj-$(CONFIG_SATA_AHCI_PLATFORM) += ahci_platform.o libahci.o +obj-$(CONFIG_SATA_AHCI_ST) += ahci_st.o obj-$(CONFIG_SATA_FSL) += sata_fsl.o obj-$(CONFIG_SATA_INIC162X) += sata_inic162x.o obj-$(CONFIG_SATA_SIL24) += sata_sil24.o
drivers/ata/ahci_st.c new file +250 -0
250 lines not on this page · raw message
Signature · 1 line
1.8.3.2
Tejun Heo
AppliedRe: [PATCH v2 3/3] ahci: st: Add support for ST's SATA IP
Quoted 4 lines · Lee Jones
Cc Tejun Heo <[email protected]>Cc linux-ide at vger.kernel.orgAcked-by Alexandre Torgue <[email protected]>Signed-off-by Lee Jones <[email protected]>
Applied to libata/for-3.15 w/ missing "\n" added to dev_err() in st_ahci_suspend().
Thanks.
Signature · 1 line
tejun
Re: [PATCH v2 3/3] ahci: st: Add support for ST's SATA IP
Quoted 8 lines · Tejun Heo
Quoted 4 lines · Lee Jones
Cc Tejun Heo <[email protected]>Cc linux-ide at vger.kernel.orgAcked-by Alexandre Torgue <[email protected]>Signed-off-by Lee Jones <[email protected]>Applied to libata/for-3.15 w/ missing "\n" added to
dev_err()inst_ahci_suspend().
Reverted from libata/for-3.15 due to build failure. Please drop ahci_platform_put_resource() calls. ahci_platform now manages it through devres.
Signature · 1 line
tejun
Re: [PATCH v2 3/3] ahci: st: Add support for ST's SATA IP
Quoted 11 lines
Quoted 7 lines
Quoted 4 lines
Cc Tejun Heo <[email protected]>Cc linux-ide at vger.kernel.orgAcked-by Alexandre Torgue <[email protected]>Signed-off-by Lee Jones <[email protected]>Applied to libata/for-3.15 w/ missing "\n" added to
dev_err()inst_ahci_suspend().Reverted from libata/for-3.15 due to build failure. Please drop
ahci_platform_put_resource()calls.ahci_platformnow manages it through devres.
Ah, nice fixup.
I'll rebase onto your most recent tree and retest.
Signature · 4 lines
Lee Jones Linaro STMicroelectronics Landing Team Lead Linaro.org ? Open source software for ARM SoCs Follow Linaro: Facebook | Twitter | Blog
PATCH v3 3/3 ahci: st: Add support for ST's SATA IP
In reply to Lee Jonesahci: st: Add support for ST's SATA IP
drivers/ata/Kconfig +9 -0
@@ -97,6 +97,15 @@ config SATA_AHCI_PLATFORM If unsure, say N. +config SATA_AHCI_ST + tristate "ST SATA support" + depends on SATA_AHCI_PLATFORM + select GENERIC_PHY + help + This option enables support for ST SATA controller. + + If unsure, say N. + config AHCI_IMX tristate "Freescale i.MX AHCI SATA support" depends on SATA_AHCI_PLATFORM && MFD_SYSCON
drivers/ata/Makefile +1 -0
@@ -5,6 +5,7 @@ obj-$(CONFIG_ATA) += libata.o obj-$(CONFIG_SATA_AHCI) += ahci.o libahci.o obj-$(CONFIG_SATA_ACARD_AHCI) += acard-ahci.o libahci.o obj-$(CONFIG_SATA_AHCI_PLATFORM) += ahci_platform.o libahci.o +obj-$(CONFIG_SATA_AHCI_ST) += ahci_st.o obj-$(CONFIG_SATA_FSL) += sata_fsl.o obj-$(CONFIG_SATA_INIC162X) += sata_inic162x.o obj-$(CONFIG_SATA_SIL24) += sata_sil24.o
drivers/ata/ahci_st.c new file +239 -0
239 lines not on this page · raw message
Re: [PATCH v3 3/3] ahci: st: Add support for ST's SATA IP
Hi,
Quoted 10 lines · Lee Jones
ahci: st: Add support for ST's SATA IP
Acked-by Alexandre Torgue <[email protected]>Signed-off-by Lee Jones <[email protected]>drivers/ata/Kconfig +0
-0
drivers/ata/Kconfig config SATA_AHCI_PLATFORM · line 100
Quoted 4 lines
drivers/ata/Kconfig +1
-0@@ -97,6 +97,15 @@ config SATA_AHCI_PLATFORM If unsure, say N. +config SATA_AHCI_ST
It would be better to name it just ACHI_ST for consistency with existing config options (AHCI_IMX and AHCI_SUNXI).
drivers/ata/Kconfig config SATA_AHCI_PLATFORM · line 101
Quoted 1 line
drivers/ata/Kconfig +1
-0+ tristate "ST SATA support"
"ST AHCI SATA support"
drivers/ata/Kconfig config SATA_AHCI_PLATFORM · line 102
Quoted 1 line
drivers/ata/Kconfig +1
-0+ depends on SATA_AHCI_PLATFORM
There should be also dependency on ARCH_STI here. We don't want this driver to be available on other ARM architectures.
drivers/ata/Kconfig config SATA_AHCI_PLATFORM · line 103
Quoted 1 line
drivers/ata/Kconfig +1
-0+ select GENERIC_PHY
This doesn't belong here anylonger and should be removed.
drivers/ata/Kconfig config SATA_AHCI_PLATFORM · line 105
Quoted 2 lines
drivers/ata/Kconfig +2
-0+ help + This option enables support for ST SATA controller.
ST AHCI SATA
Quoted 32 lines
drivers/ata/Kconfig +2
-0+ If unsure, say N. + config AHCI_IMX tristate "Freescale i.MX AHCI SATA support" depends on SATA_AHCI_PLATFORM && MFD_SYSCONdrivers/ata/Makefile +1
-0@@ -5,6 +5,7 @@ obj-$(CONFIG_ATA) += libata.o obj-$(CONFIG_SATA_AHCI) += ahci.o libahci.o obj-$(CONFIG_SATA_ACARD_AHCI) += acard-ahci.o libahci.o obj-$(CONFIG_SATA_AHCI_PLATFORM) += ahci_platform.o libahci.o +obj-$(CONFIG_SATA_AHCI_ST) += ahci_st.o obj-$(CONFIG_SATA_FSL) += sata_fsl.o obj-$(CONFIG_SATA_INIC162X) += sata_inic162x.o obj-$(CONFIG_SATA_SIL24) += sata_sil24.odrivers/ata/ahci_st.c new file +9
-0@@ -0,0 +1,239 @@ +/* +* Copyright (C) 2012 STMicroelectronics Limited +* +* Authors: Francesco Virlinzi <[email protected]> +* Alexandre Torgue <[email protected]> +* +* This program is free software; you can redistribute it and/or modify +* it under the terms of the GNU General Public License version 2 as +* published by the Free Software Foundation.
drivers/ata/ahci_st.c line 19
Quoted 10 lines
drivers/ata/ahci_st.c new file +10
-0+*/ + +#include <linux/init.h> +#include <linux/module.h> +#include <linux/export.h> +#include <linux/platform_device.h> +#include <linux/clk.h> +#include <linux/of.h> +#include <linux/ahci_platform.h> +#include <linux/phy/phy.h>
Not needed anylonger.
Quoted 7 lines
drivers/ata/ahci_st.c new file +7
-0+#include <linux/libata.h> +#include <linux/reset.h> +#include <linux/io.h> +#include <linux/dma-mapping.h> + +#include "ahci.h" +
drivers/ata/ahci_st.c line 36
Quoted 10 lines
drivers/ata/ahci_st.c new file +10
-0+#define ST_AHCI_OOBR 0xbc +#define ST_AHCI_OOBR_WE BIT(31) +#define ST_AHCI_OOBR_CWMIN_SHIFT 24 +#define ST_AHCI_OOBR_CWMAX_SHIFT 16 +#define ST_AHCI_OOBR_CIMIN_SHIFT 8 +#define ST_AHCI_OOBR_CIMAX_SHIFT 0 + +struct st_ahci_drv_data { +struct platform_device *ahci; +struct phy *phy;
ditto
Quoted 128 lines
drivers/ata/ahci_st.c new file +128
-0+struct reset_control *pwr; +struct reset_control *sw_rst; +struct reset_control *pwr_rst; +struct ahci_host_priv *hpriv; +}; + +static void st_ahci_configure_oob (void __iomem *mmio) +{ +unsigned long old_val, new_val; + + new_val = (0x02 <<ST_AHCI_OOBR_CWMIN_SHIFT ) | + (0x04 <<ST_AHCI_OOBR_CWMAX_SHIFT ) | + (0x08 <<ST_AHCI_OOBR_CIMIN_SHIFT ) | + (0x0C <<ST_AHCI_OOBR_CIMAX_SHIFT ); + + old_val =readl (mmio +ST_AHCI_OOBR ); +writel (old_val |ST_AHCI_OOBR_WE , mmio +ST_AHCI_OOBR ); +writel (new_val |ST_AHCI_OOBR_WE , mmio +ST_AHCI_OOBR ); +writel (new_val, mmio +ST_AHCI_OOBR ); +} + +static int st_ahci_deassert_resets (struct device *dev) +{ +struct st_ahci_drv_data *drv_data =dev_get_drvdata (dev); +int err; + +if (drv_data->pwr) { + err =reset_control_deassert (drv_data->pwr); +if (err) { +dev_err (dev,"unable to bring out of pwrdwn\n" ); +return err; + } + } + +st_ahci_configure_oob (drv_data->hpriv->mmio); + +if (drv_data->sw_rst) { + err =reset_control_deassert (drv_data->sw_rst); +if (err) { +dev_err (dev,"unable to bring out of sw-rst\n" ); +return err; + } + } + +if (drv_data->pwr_rst) { + err =reset_control_deassert (drv_data->pwr_rst); +if (err) { +dev_err (dev,"unable to bring out of pwr-rst\n" ); +return err; + } + } + +return 0 ; +} + +static int st_ahci_probe_resets (struct platform_device *pdev) +{ +struct st_ahci_drv_data *drv_data =platform_get_drvdata (pdev); + + drv_data->pwr =devm_reset_control_get (&pdev->dev,"pwr-dwn" ); +if (IS_ERR (drv_data->pwr)) { +dev_info (&pdev->dev,"power reset control not defined\n" ); + drv_data->pwr =NULL ; + } + + drv_data->sw_rst =devm_reset_control_get (&pdev->dev,"sw-rst" ); +if (IS_ERR (drv_data->sw_rst)) { +dev_info (&pdev->dev,"soft reset control not defined\n" ); + drv_data->sw_rst =NULL ; + } + + drv_data->pwr_rst =devm_reset_control_get (&pdev->dev,"pwr-rst" ); +if (IS_ERR (drv_data->pwr_rst)) { +dev_dbg (&pdev->dev,"power soft reset control not defined\n" ); + drv_data->pwr_rst =NULL ; + } + +return st_ahci_deassert_resets (&pdev->dev); +} + +static const struct ata_port_info st_ahci_port_info = { + .flags =AHCI_FLAG_COMMON , + .pio_mask =ATA_PIO4 , + .udma_mask =ATA_UDMA6 , + .port_ops = &ahci_platform_ops, +}; + +static int st_ahci_probe (struct platform_device *pdev) +{ +struct st_ahci_drv_data *drv_data; +struct ahci_host_priv *hpriv; +int err; + + drv_data =devm_kzalloc (&pdev->dev,sizeof (*drv_data),GFP_KERNEL ); +if (!drv_data) +return -ENOMEM ; + +platform_set_drvdata (pdev, drv_data); + + hpriv =ahci_platform_get_resources (pdev); +if (IS_ERR (hpriv)) +return PTR_ERR (hpriv); + + drv_data->hpriv = hpriv; + + err =st_ahci_probe_resets (pdev); +if (err) +return err; + + err =ahci_platform_enable_resources (hpriv); +if (err) +return err; + + err =ahci_platform_init_host (pdev, hpriv, &st_ahci_port_info,0 ,0 ); +if (err) { +ahci_platform_disable_resources (hpriv); +return err; + } + +return 0 ; +} + +static int st_ahci_remove (struct platform_device *pdev) +{ +struct st_ahci_drv_data *drv_data =platform_get_drvdata (pdev); +struct ahci_host_priv *hpriv = drv_data->hpriv; +int err; +
drivers/ata/ahci_st.c line 174
Quoted 10 lines
drivers/ata/ahci_st.c new file +10
-0+if (drv_data->pwr) { + err =reset_control_assert (drv_data->pwr); +if (err) +dev_err (&pdev->dev,"unable to pwrdwn\n" ); + } + +ahci_platform_disable_resources (hpriv); + +return 0 ; +}
This driver should define its own ->host_stop method which will do reset_control_assert() and ahci_platform_disable_resources().
Then instead of st_ahci_remove() the ata_platform_remove_one() one should be used as ->remove method.
[ Please see ahci_imx.c for details/example. ]
Quoted 6 lines
drivers/ata/ahci_st.c new file +6
-0+#ifdef CONFIG_PM_SLEEP +static int st_ahci_suspend (struct device *dev) +{ +struct st_ahci_drv_data *drv_data =dev_get_drvdata (dev); +struct ahci_host_priv *hpriv = drv_data->hpriv; +int err;
drivers/ata/ahci_st.c line 191
Quoted 10 lines
drivers/ata/ahci_st.c new file +10
-0+ +if (drv_data->pwr) { + err =reset_control_assert (drv_data->pwr); +if (err) { +dev_err (dev,"unable to pwrdwn" ); +return err; + } + } + +ahci_platform_disable_resources (hpriv);
I think that ata_platform_suspend_host() should be used in st_ahci_suspend() (please refer to ahci_imx.c).
drivers/ata/ahci_st.c line 202
Quoted 10 lines
drivers/ata/ahci_st.c new file +10
-0+return 0 ; +} + +static int st_ahci_resume (struct device *dev) +{ +struct st_ahci_drv_data *drv_data =dev_get_drvdata (dev); +struct ahci_host_priv *hpriv = drv_data->hpriv; +int err; + + err =ahci_platform_enable_resources (hpriv);
Similarly, ata_platform_resume_host() should be used in st_ahci_resume() (please refer to ahci_imx.c).
Quoted 26 lines
drivers/ata/ahci_st.c new file +26
-0+if (err) +return err; + + err =st_ahci_deassert_resets (dev); +if (err) { +ahci_platform_disable_resources (hpriv); +return err; + } + +return 0 ; +} +#endif + +static SIMPLE_DEV_PM_OPS(st_ahci_pm_ops, st_ahci_suspend, st_ahci_resume); + +static struct of_device_id st_ahci_match[] = { + { .compatible ="st,ahci" , }, + {}, +}; +MODULE_DEVICE_TABLE (of, st_ahci_match); + +static struct platform_driver st_ahci_driver = { + .driver = { + .name ="st_ahci" , + .owner =THIS_MODULE , + .pm = &st_ahci_pm_ops,
drivers/ata/ahci_st.c line 238
Quoted 10 lines
drivers/ata/ahci_st.c new file +10
-0+ .of_match_table = of_match_ptr(st_ahci_match), + }, + .probe = st_ahci_probe, + .remove = st_ahci_remove, +}; +module_platform_driver (st_ahci_driver); + +MODULE_AUTHOR ("Alexandre Torgue <[email protected]>" ); +MODULE_AUTHOR ("Francesco Virlinzi <[email protected]>" ); +MODULE_DESCRIPTION ("STMicroelectronics Sata Ahci driver" );
"Sata Ahci" -> "SATA AHCI"
drivers/ata/ahci_st.c line 239
Quoted 1 line
drivers/ata/ahci_st.c new file +1
-0+MODULE_LICENSE ("GPL v2" );
Best regards,
--
Bartlomiej Zolnierkiewicz
Samsung R&D Institute Poland
Samsung Electronics
Re: [PATCH v3 3/3] ahci: st: Add support for ST's SATA IP
Quoted 15 lines · Bartlomiej Zolnierkiewicz
Hi,
Quoted 11 lines · Lee Jones
ahci: st: Add support for ST's SATA IP
Acked-by Alexandre Torgue <[email protected]>Signed-off-by Lee Jones <[email protected]>drivers/ata/Kconfig +0
-0@@ -97,6 +97,15 @@ config SATA_AHCI_PLATFORM
Quoted 6 lines
drivers/ata/Kconfig config SATA_AHCI_PLATFORM · line 100
Quoted 3 lines
drivers/ata/Kconfig +1
-0If unsure, say N. +config SATA_AHCI_STIt would be better to name it just
ACHI_STfor consistency with existing config options (AHCI_IMXandAHCI_SUNXI).
The patch is already in for-3.15 branch. Lee, can you please post an incremental patch addressing Bart's review points?
Thanks.
Signature · 1 line
tejun
Quoted 15 lines · Lee Jones
Cc devicetree at vger.kernel.orgCc Srinivas Kandagatla <[email protected]>Acked-by Alexandre Torgue <[email protected]>Signed-off-by Lee Jones <[email protected]>--- Documentation/devicetree/bindings/ata/ahci-st.txt | 31 +++++++++++++++++++++++ 1 file changed, 31 insertions(+) create mode 100644 Documentation/devicetree/bindings/ata/ahci-st.txtDocumentation/devicetree/bindings/ata/ahci-st.txt new file +0
-0
Documentation/devicetree/bindings/ata/ahci-st.txt line 1
Quoted 1 line
Documentation/devicetree/bindings/ata/ahci-st.txt new file +1
-0@@ -0,0 +1,31 @@ +STMicroelectronics STi SATA controller
Is that a family name or a particular device?
Documentation/devicetree/bindings/ata/ahci-st.txt line 6
Quoted 5 lines
Documentation/devicetree/bindings/ata/ahci-st.txt new file +5
-0+ +This binding describes a SATA device. + +Required properties: + - compatible : Must be "st,ahci"
Is there not a more specific name? This is awfully generic.
Documentation/devicetree/bindings/ata/ahci-st.txt line 11
Quoted 5 lines
Documentation/devicetree/bindings/ata/ahci-st.txt new file +5
-0+ - reg : Physical base addresses and length of register sets + - interrupts : Interrupt associated with the SATA device + - interrupt-names : Associated name must be; "hostc" + - resets : The power-down and soft-reset lines of SATA IP + - reset-names : Associated names must be; "pwr-dwn" and "sw-rst"
Get rid of the semicolon, it makes this harder to read. Same for the other -names proeprties.
Documentation/devicetree/bindings/ata/ahci-st.txt line 15
Quoted 4 lines
Documentation/devicetree/bindings/ata/ahci-st.txt new file +4
-0+ - clocks : The phandle for the clock + - clock-names : Associated name must be; "ahci_clk" + - phys : The phandle for the PHY device + - phy-names : Associated name must be; "ahci_phy"
This looks sane, but I'd like to see a more specific description and compatible string.
Cheers,
Mark.
Quoted 24 lines
Documentation/devicetree/bindings/ata/ahci-st.txt new file +16
-0+ +Example: + + sata0: sata at fe380000 { + compatible = "st,ahci"; + reg = <0xfe380000 0x1000>; + interrupts = <GIC_SPI 157 IRQ_TYPE_NONE>; + interrupt-names = "hostc"; + phys = <&miphy365x_phy MIPHY_PORT_0 MIPHY_TYPE_SATA>; + phy-names = "ahci_phy"; + resets = <&powerdown STIH416_SATA0_POWERDOWN>, + <&softreset STIH416_SATA0_SOFTRESET>; + reset-names = "pwr-dwn", "sw-rst"; + clocks = <&CLK_S_ICN_REG_0>; + clock-names = "ahci_clk"; + };Signature · 6 lines
1.8.3.2 -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo at vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Quoted 6 lines
Documentation/devicetree/bindings/ata/ahci-st.txt line 6
Quoted 4 lines
Documentation/devicetree/bindings/ata/ahci-st.txt new file +4
-0+This binding describes a SATA device. + +Required properties: + - compatible : Must be "st,ahci"Is there not a more specific name? This is awfully generic.
There isn't one. ST only have one AHCI driver. The driver is named as generically.
Quoted 8 lines
Quoted 5 lines
+ - reg : Physical base addresses and length of register sets
+ - interrupts : Interrupt associated with the SATA device
+ - interrupt-names : Associated name must be; "hostc"
+ - resets : The power-down and soft-reset lines of SATA IP
+ - reset-names : Associated names must be; "pwr-dwn" and "sw-rst"Get rid of the semicolon, it makes this harder to read. Same for the other -names proeprties.
Sure.
Quoted 7 lines
Quoted 4 lines
+ - clocks : The phandle for the clock
+ - clock-names : Associated name must be; "ahci_clk"
+ - phys : The phandle for the PHY device
+ - phy-names : Associated name must be; "ahci_phy"This looks sane, but I'd like to see a more specific description and compatible string.
Specific description in what sense?
"This binding describes a SATA device."
to
"This binding describes ST's SATA device." ?
Quoted 15 lines
Quoted 15 lines
Documentation/devicetree/bindings/ata/ahci-st.txt new file +15
-0+Example: + + sata0: sata at fe380000 { + compatible = "st,ahci"; + reg = <0xfe380000 0x1000>; + interrupts = <GIC_SPI 157 IRQ_TYPE_NONE>; + interrupt-names = "hostc"; + phys = <&miphy365x_phy MIPHY_PORT_0 MIPHY_TYPE_SATA>; + phy-names = "ahci_phy"; + resets = <&powerdown STIH416_SATA0_POWERDOWN>, + <&softreset STIH416_SATA0_SOFTRESET>; + reset-names = "pwr-dwn", "sw-rst"; + clocks = <&CLK_S_ICN_REG_0>; + clock-names = "ahci_clk"; + };
Signature · 4 lines
Lee Jones Linaro STMicroelectronics Landing Team Lead Linaro.org ? Open source software for ARM SoCs Follow Linaro: Facebook | Twitter | Blog
Quoted 9 lines · On Wednesday 12 March 2014 12:48:35 Lee Jones wrote:
Quoted 6 lines
Documentation/devicetree/bindings/ata/ahci-st.txt line 6
Quoted 4 lines
Documentation/devicetree/bindings/ata/ahci-st.txt new file +4
-0+This binding describes a SATA device. + +Required properties: + - compatible : Must be "st,ahci"Is there not a more specific name? This is awfully generic.
There isn't one. ST only have one AHCI driver. The driver is named as generically.
If it is this generic, can't you use the completely generic ahci-platform driver and add a "generic-ahci" compatible string to that?
Arnd
Quoted 7 lines
Quoted 7 lines
Quoted 6 lines
Documentation/devicetree/bindings/ata/ahci-st.txt line 6
Quoted 4 lines
Documentation/devicetree/bindings/ata/ahci-st.txt new file +4
-0+This binding describes a SATA device. + +Required properties: + - compatible : Must be "st,ahci"Is there not a more specific name? This is awfully generic.
Quoted 6 lines
Quoted 2 lines
There isn't one. ST only have one AHCI driver. The driver is named as generically.
If it is this generic, can't you use the completely generic ahci-platform driver and add a "generic-ahci" compatible string to that?
It pretty much does. The only 'special' functionality we handle in the driver are resets and configuring the OOB. However, both are required.
Signature · 4 lines
Lee Jones Linaro STMicroelectronics Landing Team Lead Linaro.org ? Open source software for ARM SoCs Follow Linaro: Facebook | Twitter | Blog
Quoted 10 lines · On Wednesday 12 March 2014 17:14:52 Lee Jones wrote:
Quoted 10 lines
Quoted 9 lines
Quoted 6 lines
Documentation/devicetree/bindings/ata/ahci-st.txt line 6
Quoted 4 lines
Documentation/devicetree/bindings/ata/ahci-st.txt new file +4
-0+This binding describes a SATA device. + +Required properties: + - compatible : Must be "st,ahci"Is there not a more specific name? This is awfully generic.
There isn't one. ST only have one AHCI driver. The driver is named as generically.
Quoted 7 lines
Quoted 3 lines
If it is this generic, can't you use the completely generic ahci-platform driver and add a "generic-ahci" compatible string to that?
It pretty much does. The only 'special' functionality we handle in the driver are resets and configuring the OOB. However, both are required.
The reset handling should be easy to add to the generic driver usign as an optional property if I'm not mistaken.
What is OOB?
Arnd