Skip to contentSkip to conversation

spi: clps711x: Remove duplicate code to set default bits_per_word and max speed

PATCH Applied Axel Lin 2 participants 2 messages Mar 2, 2014 – Mar 13, 2014 SPI

lore
Share & tools
lore

Axel Lin

author
#0 lore raw

PATCH 1/1 spi: clps711x: Remove duplicate code to set default bits_per_word and max speed

In the implementation of __spi_validate(), spi core will set transfer bits_per_word and max speed as spi device default if it is not set for this transfer. So we can remove the same logic in spi_clps711x_setup_xfer() and spi_clps711x_transfer_one().

Signed-off-by Axel Lin <[email protected]>
---
 drivers/spi/spi-clps711x.c | 9 ++++-----
 1 file changed, 4 insertions(+), 5 deletions(-)
drivers/spi/spi-clps711x.c +4 -5
index 3900c31..74642f8 100644
@@ -44,17 +44,16 @@ static int spi_clps711x_setup(struct spi_device *spi)
 static void spi_clps711x_setup_xfer(struct spi_device *spi,
 				    struct spi_transfer *xfer)
 {
-	u32 speed = xfer->speed_hz ? : spi->max_speed_hz;
 	struct spi_clps711x_data *hw = spi_master_get_devdata(spi->master);
 
 	/* Setup SPI frequency divider */
-	if (!speed || (speed >= hw->max_speed_hz))
+	if (!xfer->speed_hz || (xfer->speed_hz >= hw->max_speed_hz))
 		clps_writel((clps_readl(SYSCON1) & ~SYSCON1_ADCKSEL_MASK) |
 			    SYSCON1_ADCKSEL(3), SYSCON1);
-	else if (speed >= (hw->max_speed_hz / 2))
+	else if (xfer->speed_hz >= (hw->max_speed_hz / 2))
 		clps_writel((clps_readl(SYSCON1) & ~SYSCON1_ADCKSEL_MASK) |
 			    SYSCON1_ADCKSEL(2), SYSCON1);
-	else if (speed >= (hw->max_speed_hz / 8))
+	else if (xfer->speed_hz >= (hw->max_speed_hz / 8))
 		clps_writel((clps_readl(SYSCON1) & ~SYSCON1_ADCKSEL_MASK) |
 			    SYSCON1_ADCKSEL(1), SYSCON1);
 	else

@@ -86,7 +85,7 @@ static int spi_clps711x_transfer_one(struct spi_master *master,
 	spi_clps711x_setup_xfer(spi, xfer);
 
 	hw->len = xfer->len;
-	hw->bpw = xfer->bits_per_word ? : spi->bits_per_word;
+	hw->bpw = xfer->bits_per_word;
 	hw->tx_buf = (u8 *)xfer->tx_buf;
 	hw->rx_buf = (u8 *)xfer->rx_buf;
Signature · 8 lines
1.8.1.2



--
To unsubscribe from this list: send the line "unsubscribe linux-spi" in
the body of a message to [email protected]
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Applied
#1 lore raw
Quoted 4 lines · Axel Lin

In the implementation of __spi_validate(), spi core will set transfer bits_per_word and max speed as spi device default if it is not set for this transfer. So we can remove the same logic in spi_clps711x_setup_xfer() and spi_clps711x_transfer_one().

Applied, thanks.