Skip to contentSkip to conversation

ARM: sun4i: spi: Allow transfers larger than FIFO size

PATCH Superseded Alexandru Gagniuc 2 participants 10 messages Mar 19, 2014 – Apr 1, 2014

Subsystems (2)
SPI Arm/Allwinner sunXi SoC support
lore
Share & tools
lore

Alexandru Gagniuc

author
#0 lore raw

v2 cover ARM: sun4i: spi: Allow transfers larger than FIFO size

This is the second iteration of the patches sent yesterday. Per Maxime's request, I have squashed them into one single patch, and applied most of the suggestion he made.

As far as only clearing the interrupt _after_ draining the FIFO, I found that we usually get one extra Rx interrupt per burst if we do this, so I left the comment in.

Quoted 11 lines

Review

Quoted 8 lines
      /* Enable the interrupts */
(quoted diff) +5 -2
-     sun4i_spi_write(sspi, SUN4I_INT_CTL_REG, SUN4I_INT_CTL_TC |
-                                              SUN4I_INT_CTL_RF_F34);
+     reg = SUN4I_INT_CTL_TC | SUN4I_INT_CTL_RF_F34;
+     /* Only enable Tx FIFO interrupt if we really need it */
+     if (tx_len > SUN4I_FIFO_DEPTH)
+             reg |= SUN4I_INT_CTL_TF_E34;
+     sun4i_spi_write(sspi, SUN4I_INT_CTL_REG, reg);

I'd be much dumber than that. Why don't you just enable both interrupts all the time if we need larger transfers ?

As I've pointed out previously, this interrupt is PITA, as it triggers an IRQ storm if enabled without much thought. I found that (tx_len > SUN4I_FIFO_DEPTH) is the best check for when it's safe to enable this interrupt.

Alexandru Gagniuc (1):
ARM: sun4i: spi: Allow transfers larger than FIFO size

 drivers/spi/spi-sun4i.c | 68 +++++++++++++++++++++++++++++++++++++++++++++----
 1 file changed, 63 insertions(+), 5 deletions(-)

--
1.8.5.3

author
#1 lore raw

PATCH v2 1/1 ARM: sun4i: spi: Allow transfers larger than FIFO size

SPI transfers were limited to one FIFO depth, which is 64 bytes. This was an artificial limitation, however, as the hardware can handle much larger bursts. To accommodate this, we enable the interrupt when the Rx FIFO is 3/4 full, and drain the FIFO within the interrupt handler. The 3/4 ratio was chosen arbitrarily, with the intention to reduce the potential number of interrupts.

Since the SUN4I_CTL_TP bit is set, the hardware will pause transmission whenever the FIFO is full, so there is no risk of losing data if we can't service the interrupt in time.

For the Tx side, enable and use the Tx FIFO 3/4 empty interrupt to replenish the FIFO on large SPI bursts. This requires more care in when the interrupt is left enabled, as this interrupt will continually trigger when the FIFO is less than 1/4 full, even though we acknowledge it.

Signed-off-by Alexandru Gagniuc <[email protected]>
---
 drivers/spi/spi-sun4i.c | 68 +++++++++++++++++++++++++++++++++++++++++++++----
 1 file changed, 63 insertions(+), 5 deletions(-)
drivers/spi/spi-sun4i.c +63 -5
index 3f82705..a12da6d 100644
@@ -47,6 +47,8 @@
 #define SUN4I_CTL_TP				BIT(18)
 
 #define SUN4I_INT_CTL_REG		0x0c
+#define SUN4I_INT_CTL_RF_F34			BIT(4)
+#define SUN4I_INT_CTL_TF_E34			BIT(12)
 #define SUN4I_INT_CTL_TC			BIT(16)
 
 #define SUN4I_INT_STA_REG		0x10

@@ -68,6 +70,8 @@
 #define SUN4I_XMIT_CNT_REG		0x24
 #define SUN4I_XMIT_CNT(cnt)			((cnt) & 0xffffff)
 
+#define SUN4I_MAX_XFER_SIZE			0xffffff
+
 #define SUN4I_FIFO_STA_REG		0x28
 #define SUN4I_FIFO_STA_RF_CNT_MASK		0x7f
 #define SUN4I_FIFO_STA_RF_CNT_BITS		0

@@ -97,6 +101,28 @@ static inline void sun4i_spi_write(struct sun4i_spi *sspi, u32 reg, u32 value)
 	writel(value, sspi->base_addr + reg);
 }
 
+static inline u32 sun4i_spi_get_tx_fifo_count(struct sun4i_spi *sspi)
+{
+	u32 reg;
+	reg = sun4i_spi_read(sspi, SUN4I_FIFO_STA_REG);
+	reg >>= SUN4I_FIFO_STA_TF_CNT_BITS;
+	return reg & SUN4I_FIFO_STA_TF_CNT_MASK;
+}
+
+static inline void sun4i_spi_enable_interrupt(struct sun4i_spi *sspi, u32 mask)
+{
+	u32 reg = sun4i_spi_read(sspi, SUN4I_INT_CTL_REG);
+	reg |= mask;
+	sun4i_spi_write(sspi, SUN4I_INT_CTL_REG, reg);
+}
+
+static inline void sun4i_spi_disable_interrupt(struct sun4i_spi *sspi, u32 mask)
+{
+	u32 reg = sun4i_spi_read(sspi, SUN4I_INT_CTL_REG);
+	reg &= ~mask;
+	sun4i_spi_write(sspi, SUN4I_INT_CTL_REG, reg);
+}
+
 static inline void sun4i_spi_drain_fifo(struct sun4i_spi *sspi, int len)
 {
 	u32 reg, cnt;

@@ -119,8 +145,15 @@ static inline void sun4i_spi_drain_fifo(struct sun4i_spi *sspi, int len)
 
 static inline void sun4i_spi_fill_fifo(struct sun4i_spi *sspi, int len)
 {
+	u32 cnt;
 	u8 byte;
 
+	/* See how much data we can fit */
+	cnt = SUN4I_FIFO_DEPTH - sun4i_spi_get_tx_fifo_count(sspi);
+
+	if (len > cnt)
+		len = cnt;
+
 	if (len > sspi->len)
 		len = sspi->len;
 

@@ -175,8 +208,7 @@ static int sun4i_spi_transfer_one(struct spi_master *master,
 	int ret = 0;
 	u32 reg;
 
-	/* We don't support transfer larger than the FIFO */
-	if (tfr->len > SUN4I_FIFO_DEPTH)
+	if (tfr->len > SUN4I_MAX_XFER_SIZE)
 		return -EINVAL;
 
 	reinit_completion(&sspi->done);

@@ -274,7 +306,11 @@ static int sun4i_spi_transfer_one(struct spi_master *master,
 	sun4i_spi_fill_fifo(sspi, SUN4I_FIFO_DEPTH);
 
 	/* Enable the interrupts */
-	sun4i_spi_write(sspi, SUN4I_INT_CTL_REG, SUN4I_INT_CTL_TC);
+	reg = SUN4I_INT_CTL_TC | SUN4I_INT_CTL_RF_F34;
+	/* Only enable Tx FIFO interrupt if we really need it */
+	if (tx_len > SUN4I_FIFO_DEPTH)
+		reg |= SUN4I_INT_CTL_TF_E34;
+	sun4i_spi_write(sspi, SUN4I_INT_CTL_REG, reg);
 
 	/* Start the transfer */
 	reg = sun4i_spi_read(sspi, SUN4I_CTL_REG);

@@ -287,8 +323,6 @@ static int sun4i_spi_transfer_one(struct spi_master *master,
 		goto out;
 	}
 
-	sun4i_spi_drain_fifo(sspi, SUN4I_FIFO_DEPTH);
-
 out:
 	sun4i_spi_write(sspi, SUN4I_INT_CTL_REG, 0);
 

@@ -299,14 +333,38 @@ static irqreturn_t sun4i_spi_handler(int irq, void *dev_id)
 {
 	struct sun4i_spi *sspi = dev_id;
 	u32 status = sun4i_spi_read(sspi, SUN4I_INT_STA_REG);
+	u32 cnt;
 
 	/* Transfer complete */
 	if (status & SUN4I_INT_CTL_TC) {
 		sun4i_spi_write(sspi, SUN4I_INT_STA_REG, SUN4I_INT_CTL_TC);
+		sun4i_spi_drain_fifo(sspi, SUN4I_FIFO_DEPTH);
 		complete(&sspi->done);
 		return IRQ_HANDLED;
 	}
 
+	/* Receive FIFO 3/4 full */
+	if (status & SUN4I_INT_CTL_RF_F34) {
+		sun4i_spi_drain_fifo(sspi, SUN4I_FIFO_DEPTH);
+		/* Only clear the interrupt _after_ draining the FIFO */
+		sun4i_spi_write(sspi, SUN4I_INT_STA_REG, SUN4I_INT_CTL_RF_F34);
+		return IRQ_HANDLED;
+	}
+
+	/* Transmit FIFO 3/4 empty */
+	if (status & SUN4I_INT_CTL_TF_E34) {
+		sun4i_spi_fill_fifo(sspi, SUN4I_FIFO_DEPTH);
+
+		if(!sspi->len)
+			/* nothing left to transmit */
+			sun4i_spi_disable_interrupt(sspi, SUN4I_INT_CTL_TF_E34);
+
+		/* Only clear the interrupt _after_ re-seeding the FIFO */
+		sun4i_spi_write(sspi, SUN4I_INT_STA_REG, SUN4I_INT_CTL_TF_E34);
+
+		return IRQ_HANDLED;
+	}
+
 	return IRQ_NONE;
 }

--
1.8.5.3

author
#2 lore raw

v2 cover ARM: sun4i: spi: Allow transfers larger than FIFO size

In reply to Alexandru Gagniuc

This is the second iteration of the patches sent yesterday. Per Maxime's request, I have squashed them into one single patch, and applied most of the suggestion he made.

As far as only clearing the interrupt _after_ draining the FIFO, I found that we usually get one extra Rx interrupt per burst if we do this, so I left the comment in.

Quoted 11 lines

Review

Quoted 8 lines
      /* Enable the interrupts */
(quoted diff) +5 -2
-     sun4i_spi_write(sspi, SUN4I_INT_CTL_REG, SUN4I_INT_CTL_TC |
-                                              SUN4I_INT_CTL_RF_F34);
+     reg = SUN4I_INT_CTL_TC | SUN4I_INT_CTL_RF_F34;
+     /* Only enable Tx FIFO interrupt if we really need it */
+     if (tx_len > SUN4I_FIFO_DEPTH)
+             reg |= SUN4I_INT_CTL_TF_E34;
+     sun4i_spi_write(sspi, SUN4I_INT_CTL_REG, reg);

I'd be much dumber than that. Why don't you just enable both interrupts all the time if we need larger transfers ?

As I've pointed out previously, this interrupt is PITA, as it triggers an IRQ storm if enabled without much thought. I found that (tx_len > SUN4I_FIFO_DEPTH) is the best check for when it's safe to enable this interrupt.

Alexandru Gagniuc (1):
ARM: sun4i: spi: Allow transfers larger than FIFO size

 drivers/spi/spi-sun4i.c | 68 +++++++++++++++++++++++++++++++++++++++++++++----
 1 file changed, 63 insertions(+), 5 deletions(-)

--
1.8.5.3

author
#3 lore raw

PATCH v3 1/1 ARM: sun4i: spi: Allow transfers larger than FIFO size

In reply to Alexandru Gagniuc

SPI transfers were limited to one FIFO depth, which is 64 bytes. This was an artificial limitation, however, as the hardware can handle much larger bursts. To accommodate this, we enable the interrupt when the Rx FIFO is 3/4 full, and drain the FIFO within the interrupt handler. The 3/4 ratio was chosen arbitrarily, with the intention to reduce the potential number of interrupts.

Since the SUN4I_CTL_TP bit is set, the hardware will pause transmission whenever the FIFO is full, so there is no risk of losing data if we can't service the interrupt in time.

For the Tx side, enable and use the Tx FIFO 3/4 empty interrupt to replenish the FIFO on large SPI bursts. This requires more care in when the interrupt is left enabled, as this interrupt will continually trigger when the FIFO is less than 1/4 full, even though we acknowledge it.

Signed-off-by Alexandru Gagniuc <[email protected]>
---
 drivers/spi/spi-sun4i.c | 67 +++++++++++++++++++++++++++++++++++++++++++++----
 1 file changed, 62 insertions(+), 5 deletions(-)
drivers/spi/spi-sun4i.c +62 -5
index 3f82705..9dd55d3 100644
@@ -47,6 +47,8 @@
 #define SUN4I_CTL_TP				BIT(18)
 
 #define SUN4I_INT_CTL_REG		0x0c
+#define SUN4I_INT_CTL_RF_F34			BIT(4)
+#define SUN4I_INT_CTL_TF_E34			BIT(12)
 #define SUN4I_INT_CTL_TC			BIT(16)
 
 #define SUN4I_INT_STA_REG		0x10

@@ -68,6 +70,8 @@
 #define SUN4I_XMIT_CNT_REG		0x24
 #define SUN4I_XMIT_CNT(cnt)			((cnt) & 0xffffff)
 
+#define SUN4I_MAX_XFER_SIZE			0xffffff
+
 #define SUN4I_FIFO_STA_REG		0x28
 #define SUN4I_FIFO_STA_RF_CNT_MASK		0x7f
 #define SUN4I_FIFO_STA_RF_CNT_BITS		0

@@ -97,6 +101,28 @@ static inline void sun4i_spi_write(struct sun4i_spi *sspi, u32 reg, u32 value)
 	writel(value, sspi->base_addr + reg);
 }
 
+static inline u32 sun4i_spi_get_tx_fifo_count(struct sun4i_spi *sspi)
+{
+	u32 reg;
+	reg = sun4i_spi_read(sspi, SUN4I_FIFO_STA_REG);
+	reg >>= SUN4I_FIFO_STA_TF_CNT_BITS;
+	return reg & SUN4I_FIFO_STA_TF_CNT_MASK;
+}
+
+static inline void sun4i_spi_enable_interrupt(struct sun4i_spi *sspi, u32 mask)
+{
+	u32 reg = sun4i_spi_read(sspi, SUN4I_INT_CTL_REG);
+	reg |= mask;
+	sun4i_spi_write(sspi, SUN4I_INT_CTL_REG, reg);
+}
+
+static inline void sun4i_spi_disable_interrupt(struct sun4i_spi *sspi, u32 mask)
+{
+	u32 reg = sun4i_spi_read(sspi, SUN4I_INT_CTL_REG);
+	reg &= ~mask;
+	sun4i_spi_write(sspi, SUN4I_INT_CTL_REG, reg);
+}
+
 static inline void sun4i_spi_drain_fifo(struct sun4i_spi *sspi, int len)
 {
 	u32 reg, cnt;

@@ -119,8 +145,15 @@ static inline void sun4i_spi_drain_fifo(struct sun4i_spi *sspi, int len)
 
 static inline void sun4i_spi_fill_fifo(struct sun4i_spi *sspi, int len)
 {
+	u32 cnt;
 	u8 byte;
 
+	/* See how much data we can fit */
+	cnt = SUN4I_FIFO_DEPTH - sun4i_spi_get_tx_fifo_count(sspi);
+
+	if (len > cnt)
+		len = cnt;
+
 	if (len > sspi->len)
 		len = sspi->len;
 

@@ -175,8 +208,7 @@ static int sun4i_spi_transfer_one(struct spi_master *master,
 	int ret = 0;
 	u32 reg;
 
-	/* We don't support transfer larger than the FIFO */
-	if (tfr->len > SUN4I_FIFO_DEPTH)
+	if (tfr->len > SUN4I_MAX_XFER_SIZE)
 		return -EINVAL;
 
 	reinit_completion(&sspi->done);

@@ -274,7 +306,11 @@ static int sun4i_spi_transfer_one(struct spi_master *master,
 	sun4i_spi_fill_fifo(sspi, SUN4I_FIFO_DEPTH);
 
 	/* Enable the interrupts */
-	sun4i_spi_write(sspi, SUN4I_INT_CTL_REG, SUN4I_INT_CTL_TC);
+	reg = SUN4I_INT_CTL_TC | SUN4I_INT_CTL_RF_F34;
+	/* Only enable Tx FIFO interrupt if we really need it */
+	if (tx_len > SUN4I_FIFO_DEPTH)
+		reg |= SUN4I_INT_CTL_TF_E34;
+	sun4i_spi_write(sspi, SUN4I_INT_CTL_REG, reg);
 
 	/* Start the transfer */
 	reg = sun4i_spi_read(sspi, SUN4I_CTL_REG);

@@ -287,8 +323,6 @@ static int sun4i_spi_transfer_one(struct spi_master *master,
 		goto out;
 	}
 
-	sun4i_spi_drain_fifo(sspi, SUN4I_FIFO_DEPTH);
-
 out:
 	sun4i_spi_write(sspi, SUN4I_INT_CTL_REG, 0);
 

@@ -303,10 +337,33 @@ static irqreturn_t sun4i_spi_handler(int irq, void *dev_id)
 	/* Transfer complete */
 	if (status & SUN4I_INT_CTL_TC) {
 		sun4i_spi_write(sspi, SUN4I_INT_STA_REG, SUN4I_INT_CTL_TC);
+		sun4i_spi_drain_fifo(sspi, SUN4I_FIFO_DEPTH);
 		complete(&sspi->done);
 		return IRQ_HANDLED;
 	}
 
+	/* Receive FIFO 3/4 full */
+	if (status & SUN4I_INT_CTL_RF_F34) {
+		sun4i_spi_drain_fifo(sspi, SUN4I_FIFO_DEPTH);
+		/* Only clear the interrupt _after_ draining the FIFO */
+		sun4i_spi_write(sspi, SUN4I_INT_STA_REG, SUN4I_INT_CTL_RF_F34);
+		return IRQ_HANDLED;
+	}
+
+	/* Transmit FIFO 3/4 empty */
+	if (status & SUN4I_INT_CTL_TF_E34) {
+		sun4i_spi_fill_fifo(sspi, SUN4I_FIFO_DEPTH);
+
+		if(!sspi->len)
+			/* nothing left to transmit */
+			sun4i_spi_disable_interrupt(sspi, SUN4I_INT_CTL_TF_E34);
+
+		/* Only clear the interrupt _after_ re-seeding the FIFO */
+		sun4i_spi_write(sspi, SUN4I_INT_STA_REG, SUN4I_INT_CTL_TF_E34);
+
+		return IRQ_HANDLED;
+	}
+
 	return IRQ_NONE;
 }

--
1.8.5.3

#4 lore raw

PATCH v3 1/1 ARM: sun4i: spi: Allow transfers larger than FIFO size

Quoted 36 lines · Alexandru Gagniuc

SPI transfers were limited to one FIFO depth, which is 64 bytes. This was an artificial limitation, however, as the hardware can handle much larger bursts. To accommodate this, we enable the interrupt when the Rx FIFO is 3/4 full, and drain the FIFO within the interrupt handler. The 3/4 ratio was chosen arbitrarily, with the intention to reduce the potential number of interrupts.

Since the SUN4I_CTL_TP bit is set, the hardware will pause transmission whenever the FIFO is full, so there is no risk of losing data if we can't service the interrupt in time.

For the Tx side, enable and use the Tx FIFO 3/4 empty interrupt to replenish the FIFO on large SPI bursts. This requires more care in when the interrupt is left enabled, as this interrupt will continually trigger when the FIFO is less than 1/4 full, even though we acknowledge it.

Signed-off-by Alexandru Gagniuc <[email protected]>
---
 drivers/spi/spi-sun4i.c | 67 +++++++++++++++++++++++++++++++++++++++++++++----
 1 file changed, 62 insertions(+), 5 deletions(-)
drivers/spi/spi-sun4i.c +2 -0
index 3f82705..9dd55d3 100644
@@ -47,6 +47,8 @@
 #define SUN4I_CTL_TP				BIT(18)
 
 #define SUN4I_INT_CTL_REG		0x0c
+#define SUN4I_INT_CTL_RF_F34			BIT(4)
+#define SUN4I_INT_CTL_TF_E34			BIT(12)
 #define SUN4I_INT_CTL_TC			BIT(16)
 
 #define SUN4I_INT_STA_REG		0x10

drivers/spi/spi-sun4i.c line 74

Quoted 5 lines
drivers/spi/spi-sun4i.c +2 -0
@@ -68,6 +70,8 @@
 #define SUN4I_XMIT_CNT_REG		0x24
 #define SUN4I_XMIT_CNT(cnt)			((cnt) & 0xffffff)
 
+#define SUN4I_MAX_XFER_SIZE			0xffffff
+

I'd rather define the mask only once here, and reuse it in the macro just above.

Quoted 49 lines
drivers/spi/spi-sun4i.c +29 -0
 #define SUN4I_FIFO_STA_REG		0x28
 #define SUN4I_FIFO_STA_RF_CNT_MASK		0x7f
 #define SUN4I_FIFO_STA_RF_CNT_BITS		0

@@ -97,6 +101,28 @@ static inline void sun4i_spi_write(struct sun4i_spi *sspi, u32 reg, u32 value)
 	writel(value, sspi->base_addr + reg);
 }
 
+static inline u32 sun4i_spi_get_tx_fifo_count(struct sun4i_spi *sspi)
+{
+	u32 reg;
+	reg = sun4i_spi_read(sspi, SUN4I_FIFO_STA_REG);
+	reg >>= SUN4I_FIFO_STA_TF_CNT_BITS;
+	return reg & SUN4I_FIFO_STA_TF_CNT_MASK;
+}
+
+static inline void sun4i_spi_enable_interrupt(struct sun4i_spi *sspi, u32 mask)
+{
+	u32 reg = sun4i_spi_read(sspi, SUN4I_INT_CTL_REG);
+	reg |= mask;
+	sun4i_spi_write(sspi, SUN4I_INT_CTL_REG, reg);
+}
+
+static inline void sun4i_spi_disable_interrupt(struct sun4i_spi *sspi, u32 mask)
+{
+	u32 reg = sun4i_spi_read(sspi, SUN4I_INT_CTL_REG);
+	reg &= ~mask;
+	sun4i_spi_write(sspi, SUN4I_INT_CTL_REG, reg);
+}
+
 static inline void sun4i_spi_drain_fifo(struct sun4i_spi *sspi, int len)
 {
 	u32 reg, cnt;

@@ -119,8 +145,15 @@ static inline void sun4i_spi_drain_fifo(struct sun4i_spi *sspi, int len)
 
 static inline void sun4i_spi_fill_fifo(struct sun4i_spi *sspi, int len)
 {
+	u32 cnt;
 	u8 byte;
 
+	/* See how much data we can fit */
+	cnt = SUN4I_FIFO_DEPTH - sun4i_spi_get_tx_fifo_count(sspi);
+
+	if (len > cnt)
+		len = cnt;
+
 	if (len > sspi->len)
 		len = sspi->len;

drivers/spi/spi-sun4i.c static int sun4i_spi_transfer_one(struct spi_master *master, · line 211

Quoted 6 lines
drivers/spi/spi-sun4i.c +1 -2
@@ -175,8 +208,7 @@ static int sun4i_spi_transfer_one(struct spi_master *master,
 	int ret = 0;
 	u32 reg;
 
-	/* We don't support transfer larger than the FIFO */
-	if (tfr->len > SUN4I_FIFO_DEPTH)
+	if (tfr->len > SUN4I_MAX_XFER_SIZE)

A comment here about why you're doing so would be nice

drivers/spi/spi-sun4i.c static int sun4i_spi_transfer_one(struct spi_master *master, · line 313

Quoted 13 lines
drivers/spi/spi-sun4i.c +5 -1
 		return -EINVAL;
 
 	reinit_completion(&sspi->done);

@@ -274,7 +306,11 @@ static int sun4i_spi_transfer_one(struct spi_master *master,
 	sun4i_spi_fill_fifo(sspi, SUN4I_FIFO_DEPTH);
 
 	/* Enable the interrupts */
-	sun4i_spi_write(sspi, SUN4I_INT_CTL_REG, SUN4I_INT_CTL_TC);
+	reg = SUN4I_INT_CTL_TC | SUN4I_INT_CTL_RF_F34;
+	/* Only enable Tx FIFO interrupt if we really need it */
+	if (tx_len > SUN4I_FIFO_DEPTH)
+		reg |= SUN4I_INT_CTL_TF_E34;
+	sun4i_spi_write(sspi, SUN4I_INT_CTL_REG, reg);

You probably can use the _enable_interrupt function you just defined here :)

Quoted 49 lines
drivers/spi/spi-sun4i.c +23 -3
 	/* Start the transfer */
 	reg = sun4i_spi_read(sspi, SUN4I_CTL_REG);

@@ -287,8 +323,6 @@ static int sun4i_spi_transfer_one(struct spi_master *master,
 		goto out;
 	}
 
-	sun4i_spi_drain_fifo(sspi, SUN4I_FIFO_DEPTH);
-
 out:
 	sun4i_spi_write(sspi, SUN4I_INT_CTL_REG, 0);
 

@@ -303,10 +337,33 @@ static irqreturn_t sun4i_spi_handler(int irq, void *dev_id)
 	/* Transfer complete */
 	if (status & SUN4I_INT_CTL_TC) {
 		sun4i_spi_write(sspi, SUN4I_INT_STA_REG, SUN4I_INT_CTL_TC);
+		sun4i_spi_drain_fifo(sspi, SUN4I_FIFO_DEPTH);
 		complete(&sspi->done);
 		return IRQ_HANDLED;
 	}
 
+	/* Receive FIFO 3/4 full */
+	if (status & SUN4I_INT_CTL_RF_F34) {
+		sun4i_spi_drain_fifo(sspi, SUN4I_FIFO_DEPTH);
+		/* Only clear the interrupt _after_ draining the FIFO */
+		sun4i_spi_write(sspi, SUN4I_INT_STA_REG, SUN4I_INT_CTL_RF_F34);
+		return IRQ_HANDLED;
+	}
+
+	/* Transmit FIFO 3/4 empty */
+	if (status & SUN4I_INT_CTL_TF_E34) {
+		sun4i_spi_fill_fifo(sspi, SUN4I_FIFO_DEPTH);
+
+		if(!sspi->len)
+			/* nothing left to transmit */
+			sun4i_spi_disable_interrupt(sspi, SUN4I_INT_CTL_TF_E34);
+
+		/* Only clear the interrupt _after_ re-seeding the FIFO */
+		sun4i_spi_write(sspi, SUN4I_INT_STA_REG, SUN4I_INT_CTL_TF_E34);
+
+		return IRQ_HANDLED;
+	}
+
 	return IRQ_NONE;
 }
 
--

1.8.5.3

Signature · 10 lines
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 836 bytes
Desc: Digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20140322/39f2d4ba/attachment.sig>
author
#5 lore raw

PATCH v4 1/1 ARM: sun4i: spi: Allow transfers larger than FIFO size

SPI transfers were limited to one FIFO depth, which is 64 bytes. This was an artificial limitation, however, as the hardware can handle much larger bursts. To accommodate this, we enable the interrupt when the Rx FIFO is 3/4 full, and drain the FIFO within the interrupt handler. The 3/4 ratio was chosen arbitrarily, with the intention to reduce the potential number of interrupts.

Since the SUN4I_CTL_TP bit is set, the hardware will pause transmission whenever the FIFO is full, so there is no risk of losing data if we can't service the interrupt in time.

For the Tx side, enable and use the Tx FIFO 3/4 empty interrupt to replenish the FIFO on large SPI bursts. This requires more care in when the interrupt is left enabled, as this interrupt will continually trigger when the FIFO is less than 1/4 full, even though we acknowledge it.

Signed-off-by Alexandru Gagniuc <[email protected]>
---
 drivers/spi/spi-sun4i.c | 72 ++++++++++++++++++++++++++++++++++++++++++++-----
 1 file changed, 65 insertions(+), 7 deletions(-)
drivers/spi/spi-sun4i.c +65 -7
index 3f82705..1557528 100644
@@ -47,6 +47,8 @@
 #define SUN4I_CTL_TP				BIT(18)
 
 #define SUN4I_INT_CTL_REG		0x0c
+#define SUN4I_INT_CTL_RF_F34			BIT(4)
+#define SUN4I_INT_CTL_TF_E34			BIT(12)
 #define SUN4I_INT_CTL_TC			BIT(16)
 
 #define SUN4I_INT_STA_REG		0x10

@@ -62,11 +64,14 @@
 #define SUN4I_CLK_CTL_CDR1(div)			(((div) & SUN4I_CLK_CTL_CDR1_MASK) << 8)
 #define SUN4I_CLK_CTL_DRS			BIT(12)
 
+#define SUN4I_MAX_XFER_SIZE			0xffffff
+
 #define SUN4I_BURST_CNT_REG		0x20
-#define SUN4I_BURST_CNT(cnt)			((cnt) & 0xffffff)
+#define SUN4I_BURST_CNT(cnt)			((cnt) & SUN4I_MAX_XFER_SIZE)
 
 #define SUN4I_XMIT_CNT_REG		0x24
-#define SUN4I_XMIT_CNT(cnt)			((cnt) & 0xffffff)
+#define SUN4I_XMIT_CNT(cnt)			((cnt) & SUN4I_MAX_XFER_SIZE)
+
 
 #define SUN4I_FIFO_STA_REG		0x28
 #define SUN4I_FIFO_STA_RF_CNT_MASK		0x7f

@@ -97,6 +102,28 @@ static inline void sun4i_spi_write(struct sun4i_spi *sspi, u32 reg, u32 value)
 	writel(value, sspi->base_addr + reg);
 }
 
+static inline u32 sun4i_spi_get_tx_fifo_count(struct sun4i_spi *sspi)
+{
+	u32 reg;
+	reg = sun4i_spi_read(sspi, SUN4I_FIFO_STA_REG);
+	reg >>= SUN4I_FIFO_STA_TF_CNT_BITS;
+	return reg & SUN4I_FIFO_STA_TF_CNT_MASK;
+}
+
+static inline void sun4i_spi_enable_interrupt(struct sun4i_spi *sspi, u32 mask)
+{
+	u32 reg = sun4i_spi_read(sspi, SUN4I_INT_CTL_REG);
+	reg |= mask;
+	sun4i_spi_write(sspi, SUN4I_INT_CTL_REG, reg);
+}
+
+static inline void sun4i_spi_disable_interrupt(struct sun4i_spi *sspi, u32 mask)
+{
+	u32 reg = sun4i_spi_read(sspi, SUN4I_INT_CTL_REG);
+	reg &= ~mask;
+	sun4i_spi_write(sspi, SUN4I_INT_CTL_REG, reg);
+}
+
 static inline void sun4i_spi_drain_fifo(struct sun4i_spi *sspi, int len)
 {
 	u32 reg, cnt;

@@ -119,8 +146,15 @@ static inline void sun4i_spi_drain_fifo(struct sun4i_spi *sspi, int len)
 
 static inline void sun4i_spi_fill_fifo(struct sun4i_spi *sspi, int len)
 {
+	u32 cnt;
 	u8 byte;
 
+	/* See how much data we can fit */
+	cnt = SUN4I_FIFO_DEPTH - sun4i_spi_get_tx_fifo_count(sspi);
+
+	if (len > cnt)
+		len = cnt;
+
 	if (len > sspi->len)
 		len = sspi->len;
 

@@ -175,8 +209,8 @@ static int sun4i_spi_transfer_one(struct spi_master *master,
 	int ret = 0;
 	u32 reg;
 
-	/* We don't support transfer larger than the FIFO */
-	if (tfr->len > SUN4I_FIFO_DEPTH)
+	/* This is the maximum SPI burst size supported by the hardware */
+	if (tfr->len > SUN4I_MAX_XFER_SIZE)
 		return -EINVAL;
 
 	reinit_completion(&sspi->done);

@@ -274,7 +308,10 @@ static int sun4i_spi_transfer_one(struct spi_master *master,
 	sun4i_spi_fill_fifo(sspi, SUN4I_FIFO_DEPTH);
 
 	/* Enable the interrupts */
-	sun4i_spi_write(sspi, SUN4I_INT_CTL_REG, SUN4I_INT_CTL_TC);
+	sun4i_spi_enable_interrupt(sspi, SUN4I_INT_CTL_TC | SUN4I_INT_CTL_RF_F34);
+	/* Only enable Tx FIFO interrupt if we really need it */
+	if (tx_len > SUN4I_FIFO_DEPTH)
+		sun4i_spi_enable_interrupt(sspi, SUN4I_INT_CTL_TF_E34);
 
 	/* Start the transfer */
 	reg = sun4i_spi_read(sspi, SUN4I_CTL_REG);

@@ -287,8 +324,6 @@ static int sun4i_spi_transfer_one(struct spi_master *master,
 		goto out;
 	}
 
-	sun4i_spi_drain_fifo(sspi, SUN4I_FIFO_DEPTH);
-
 out:
 	sun4i_spi_write(sspi, SUN4I_INT_CTL_REG, 0);
 

@@ -303,10 +338,33 @@ static irqreturn_t sun4i_spi_handler(int irq, void *dev_id)
 	/* Transfer complete */
 	if (status & SUN4I_INT_CTL_TC) {
 		sun4i_spi_write(sspi, SUN4I_INT_STA_REG, SUN4I_INT_CTL_TC);
+		sun4i_spi_drain_fifo(sspi, SUN4I_FIFO_DEPTH);
 		complete(&sspi->done);
 		return IRQ_HANDLED;
 	}
 
+	/* Receive FIFO 3/4 full */
+	if (status & SUN4I_INT_CTL_RF_F34) {
+		sun4i_spi_drain_fifo(sspi, SUN4I_FIFO_DEPTH);
+		/* Only clear the interrupt _after_ draining the FIFO */
+		sun4i_spi_write(sspi, SUN4I_INT_STA_REG, SUN4I_INT_CTL_RF_F34);
+		return IRQ_HANDLED;
+	}
+
+	/* Transmit FIFO 3/4 empty */
+	if (status & SUN4I_INT_CTL_TF_E34) {
+		sun4i_spi_fill_fifo(sspi, SUN4I_FIFO_DEPTH);
+
+		if(!sspi->len)
+			/* nothing left to transmit */
+			sun4i_spi_disable_interrupt(sspi, SUN4I_INT_CTL_TF_E34);
+
+		/* Only clear the interrupt _after_ re-seeding the FIFO */
+		sun4i_spi_write(sspi, SUN4I_INT_STA_REG, SUN4I_INT_CTL_TF_E34);
+
+		return IRQ_HANDLED;
+	}
+
 	return IRQ_NONE;
 }
Signature · 1 line
1.8.5.3
#6 lore raw

PATCH v4 1/1 ARM: sun4i: spi: Allow transfers larger than FIFO size

Hi,

Thanks for respinning this patch.

Quoted 53 lines · Alexandru Gagniuc

SPI transfers were limited to one FIFO depth, which is 64 bytes. This was an artificial limitation, however, as the hardware can handle much larger bursts. To accommodate this, we enable the interrupt when the Rx FIFO is 3/4 full, and drain the FIFO within the interrupt handler. The 3/4 ratio was chosen arbitrarily, with the intention to reduce the potential number of interrupts.

Since the SUN4I_CTL_TP bit is set, the hardware will pause transmission whenever the FIFO is full, so there is no risk of losing data if we can't service the interrupt in time.

For the Tx side, enable and use the Tx FIFO 3/4 empty interrupt to replenish the FIFO on large SPI bursts. This requires more care in when the interrupt is left enabled, as this interrupt will continually trigger when the FIFO is less than 1/4 full, even though we acknowledge it.

Signed-off-by Alexandru Gagniuc <[email protected]>
---
 drivers/spi/spi-sun4i.c | 72 ++++++++++++++++++++++++++++++++++++++++++++-----
 1 file changed, 65 insertions(+), 7 deletions(-)
drivers/spi/spi-sun4i.c +7 -2
index 3f82705..1557528 100644
@@ -47,6 +47,8 @@
 #define SUN4I_CTL_TP				BIT(18)
 
 #define SUN4I_INT_CTL_REG		0x0c
+#define SUN4I_INT_CTL_RF_F34			BIT(4)
+#define SUN4I_INT_CTL_TF_E34			BIT(12)
 #define SUN4I_INT_CTL_TC			BIT(16)
 
 #define SUN4I_INT_STA_REG		0x10

@@ -62,11 +64,14 @@
 #define SUN4I_CLK_CTL_CDR1(div)			(((div) & SUN4I_CLK_CTL_CDR1_MASK) << 8)
 #define SUN4I_CLK_CTL_DRS			BIT(12)
 
+#define SUN4I_MAX_XFER_SIZE			0xffffff
+
 #define SUN4I_BURST_CNT_REG		0x20
-#define SUN4I_BURST_CNT(cnt)			((cnt) & 0xffffff)
+#define SUN4I_BURST_CNT(cnt)			((cnt) & SUN4I_MAX_XFER_SIZE)
 
 #define SUN4I_XMIT_CNT_REG		0x24
-#define SUN4I_XMIT_CNT(cnt)			((cnt) & 0xffffff)
+#define SUN4I_XMIT_CNT(cnt)			((cnt) & SUN4I_MAX_XFER_SIZE)
+
 
 #define SUN4I_FIFO_STA_REG		0x28
 #define SUN4I_FIFO_STA_RF_CNT_MASK		0x7f

drivers/spi/spi-sun4i.c static inline void sun4i_spi_write(struct sun4i_spi *sspi, u32 reg, u32 value) · line 108

Quoted 7 lines
drivers/spi/spi-sun4i.c +4 -0
@@ -97,6 +102,28 @@ static inline void sun4i_spi_write(struct sun4i_spi *sspi, u32 reg, u32 value)
 	writel(value, sspi->base_addr + reg);
 }
 
+static inline u32 sun4i_spi_get_tx_fifo_count(struct sun4i_spi *sspi)
+{
+	u32 reg;
+	reg = sun4i_spi_read(sspi, SUN4I_FIFO_STA_REG);

You seem to assign the reg variables when declaring it in other part of your code. It would be great to be consistent.

Quoted 26 lines
drivers/spi/spi-sun4i.c +19 -0
+	reg >>= SUN4I_FIFO_STA_TF_CNT_BITS;
+	return reg & SUN4I_FIFO_STA_TF_CNT_MASK;
+}
+
+static inline void sun4i_spi_enable_interrupt(struct sun4i_spi *sspi, u32 mask)
+{
+	u32 reg = sun4i_spi_read(sspi, SUN4I_INT_CTL_REG);
+	reg |= mask;
+	sun4i_spi_write(sspi, SUN4I_INT_CTL_REG, reg);
+}
+
+static inline void sun4i_spi_disable_interrupt(struct sun4i_spi *sspi, u32 mask)
+{
+	u32 reg = sun4i_spi_read(sspi, SUN4I_INT_CTL_REG);
+	reg &= ~mask;
+	sun4i_spi_write(sspi, SUN4I_INT_CTL_REG, reg);
+}
+
 static inline void sun4i_spi_drain_fifo(struct sun4i_spi *sspi, int len)
 {
 	u32 reg, cnt;

@@ -119,8 +146,15 @@ static inline void sun4i_spi_drain_fifo(struct sun4i_spi *sspi, int len)
 
 static inline void sun4i_spi_fill_fifo(struct sun4i_spi *sspi, int len)
 {
+	u32 cnt;

drivers/spi/spi-sun4i.c static inline void sun4i_spi_drain_fifo(struct sun4i_spi *sspi, int len) · line 159

Quoted 10 lines
drivers/spi/spi-sun4i.c +6 -0
 	u8 byte;
 
+	/* See how much data we can fit */
+	cnt = SUN4I_FIFO_DEPTH - sun4i_spi_get_tx_fifo_count(sspi);
+
+	if (len > cnt)
+		len = cnt;
+
 	if (len > sspi->len)
 		len = sspi->len;

You probably want to use min3 here

Quoted 44 lines
drivers/spi/spi-sun4i.c +10 -5
@@ -175,8 +209,8 @@ static int sun4i_spi_transfer_one(struct spi_master *master,
 	int ret = 0;
 	u32 reg;
 
-	/* We don't support transfer larger than the FIFO */
-	if (tfr->len > SUN4I_FIFO_DEPTH)
+	/* This is the maximum SPI burst size supported by the hardware */
+	if (tfr->len > SUN4I_MAX_XFER_SIZE)
 		return -EINVAL;
 
 	reinit_completion(&sspi->done);

@@ -274,7 +308,10 @@ static int sun4i_spi_transfer_one(struct spi_master *master,
 	sun4i_spi_fill_fifo(sspi, SUN4I_FIFO_DEPTH);
 
 	/* Enable the interrupts */
-	sun4i_spi_write(sspi, SUN4I_INT_CTL_REG, SUN4I_INT_CTL_TC);
+	sun4i_spi_enable_interrupt(sspi, SUN4I_INT_CTL_TC | SUN4I_INT_CTL_RF_F34);
+	/* Only enable Tx FIFO interrupt if we really need it */
+	if (tx_len > SUN4I_FIFO_DEPTH)
+		sun4i_spi_enable_interrupt(sspi, SUN4I_INT_CTL_TF_E34);
 
 	/* Start the transfer */
 	reg = sun4i_spi_read(sspi, SUN4I_CTL_REG);

@@ -287,8 +324,6 @@ static int sun4i_spi_transfer_one(struct spi_master *master,
 		goto out;
 	}
 
-	sun4i_spi_drain_fifo(sspi, SUN4I_FIFO_DEPTH);
-
 out:
 	sun4i_spi_write(sspi, SUN4I_INT_CTL_REG, 0);
 

@@ -303,10 +338,33 @@ static irqreturn_t sun4i_spi_handler(int irq, void *dev_id)
 	/* Transfer complete */
 	if (status & SUN4I_INT_CTL_TC) {
 		sun4i_spi_write(sspi, SUN4I_INT_STA_REG, SUN4I_INT_CTL_TC);
+		sun4i_spi_drain_fifo(sspi, SUN4I_FIFO_DEPTH);
 		complete(&sspi->done);
 		return IRQ_HANDLED;
 	}
 
+	/* Receive FIFO 3/4 full */
+	if (status & SUN4I_INT_CTL_RF_F34) {
+		sun4i_spi_drain_fifo(sspi, SUN4I_FIFO_DEPTH);

drivers/spi/spi-sun4i.c static irqreturn_t sun4i_spi_handler(int irq, void *dev_id) · line 358

Quoted 10 lines
drivers/spi/spi-sun4i.c +10 -0
+		/* Only clear the interrupt _after_ draining the FIFO */
+		sun4i_spi_write(sspi, SUN4I_INT_STA_REG, SUN4I_INT_CTL_RF_F34);
+		return IRQ_HANDLED;
+	}
+
+	/* Transmit FIFO 3/4 empty */
+	if (status & SUN4I_INT_CTL_TF_E34) {
+		sun4i_spi_fill_fifo(sspi, SUN4I_FIFO_DEPTH);
+
+		if(!sspi->len)

if (!sspi->len)

Quoted 15 lines
drivers/spi/spi-sun4i.c +9 -0
+			/* nothing left to transmit */
+			sun4i_spi_disable_interrupt(sspi, SUN4I_INT_CTL_TF_E34);
+
+		/* Only clear the interrupt _after_ re-seeding the FIFO */
+		sun4i_spi_write(sspi, SUN4I_INT_STA_REG, SUN4I_INT_CTL_TF_E34);
+
+		return IRQ_HANDLED;
+	}
+
 	return IRQ_NONE;
 }
Signature · 1 line
1.8.5.3

Once these minor issues fixed, you can add my

Acked-by Maxime Ripard <[email protected]>

Thanks!

Signature · 10 lines
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 836 bytes
Desc: Digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20140331/0ac23f01/attachment.sig>
author
#7 lore raw

PATCH v5 1/1 ARM: sun4i: spi: Allow transfers larger than FIFO size

SPI transfers were limited to one FIFO depth, which is 64 bytes. This was an artificial limitation, however, as the hardware can handle much larger bursts. To accommodate this, we enable the interrupt when the Rx FIFO is 3/4 full, and drain the FIFO within the interrupt handler. The 3/4 ratio was chosen arbitrarily, with the intention to reduce the potential number of interrupts.

Since the SUN4I_CTL_TP bit is set, the hardware will pause transmission whenever the FIFO is full, so there is no risk of losing data if we can't service the interrupt in time.

For the Tx side, enable and use the Tx FIFO 3/4 empty interrupt to replenish the FIFO on large SPI bursts. This requires more care in when the interrupt is left enabled, as this interrupt will continually trigger when the FIFO is less than 1/4 full, even though we acknowledge it.

Signed-off-by Alexandru Gagniuc <[email protected]>
Acked-by Maxime Ripard <[email protected]>
---
 drivers/spi/spi-sun4i.c | 71 ++++++++++++++++++++++++++++++++++++++++++-------
 1 file changed, 62 insertions(+), 9 deletions(-)
drivers/spi/spi-sun4i.c +62 -9
index 3f82705..d80ceba 100644
@@ -47,6 +47,8 @@
 #define SUN4I_CTL_TP				BIT(18)
 
 #define SUN4I_INT_CTL_REG		0x0c
+#define SUN4I_INT_CTL_RF_F34			BIT(4)
+#define SUN4I_INT_CTL_TF_E34			BIT(12)
 #define SUN4I_INT_CTL_TC			BIT(16)
 
 #define SUN4I_INT_STA_REG		0x10

@@ -62,11 +64,14 @@
 #define SUN4I_CLK_CTL_CDR1(div)			(((div) & SUN4I_CLK_CTL_CDR1_MASK) << 8)
 #define SUN4I_CLK_CTL_DRS			BIT(12)
 
+#define SUN4I_MAX_XFER_SIZE			0xffffff
+
 #define SUN4I_BURST_CNT_REG		0x20
-#define SUN4I_BURST_CNT(cnt)			((cnt) & 0xffffff)
+#define SUN4I_BURST_CNT(cnt)			((cnt) & SUN4I_MAX_XFER_SIZE)
 
 #define SUN4I_XMIT_CNT_REG		0x24
-#define SUN4I_XMIT_CNT(cnt)			((cnt) & 0xffffff)
+#define SUN4I_XMIT_CNT(cnt)			((cnt) & SUN4I_MAX_XFER_SIZE)
+
 
 #define SUN4I_FIFO_STA_REG		0x28
 #define SUN4I_FIFO_STA_RF_CNT_MASK		0x7f

@@ -97,6 +102,27 @@ static inline void sun4i_spi_write(struct sun4i_spi *sspi, u32 reg, u32 value)
 	writel(value, sspi->base_addr + reg);
 }
 
+static inline u32 sun4i_spi_get_tx_fifo_count(struct sun4i_spi *sspi)
+{
+	u32 reg = sun4i_spi_read(sspi, SUN4I_FIFO_STA_REG);
+	reg >>= SUN4I_FIFO_STA_TF_CNT_BITS;
+	return reg & SUN4I_FIFO_STA_TF_CNT_MASK;
+}
+
+static inline void sun4i_spi_enable_interrupt(struct sun4i_spi *sspi, u32 mask)
+{
+	u32 reg = sun4i_spi_read(sspi, SUN4I_INT_CTL_REG);
+	reg |= mask;
+	sun4i_spi_write(sspi, SUN4I_INT_CTL_REG, reg);
+}
+
+static inline void sun4i_spi_disable_interrupt(struct sun4i_spi *sspi, u32 mask)
+{
+	u32 reg = sun4i_spi_read(sspi, SUN4I_INT_CTL_REG);
+	reg &= ~mask;
+	sun4i_spi_write(sspi, SUN4I_INT_CTL_REG, reg);
+}
+
 static inline void sun4i_spi_drain_fifo(struct sun4i_spi *sspi, int len)
 {
 	u32 reg, cnt;

@@ -119,10 +145,13 @@ static inline void sun4i_spi_drain_fifo(struct sun4i_spi *sspi, int len)
 
 static inline void sun4i_spi_fill_fifo(struct sun4i_spi *sspi, int len)
 {
+	u32 cnt;
 	u8 byte;
 
-	if (len > sspi->len)
-		len = sspi->len;
+	/* See how much data we can fit */
+	cnt = SUN4I_FIFO_DEPTH - sun4i_spi_get_tx_fifo_count(sspi);
+
+	len = min3(len, (int)cnt, sspi->len);
 
 	while (len--) {
 		byte = sspi->tx_buf ? *sspi->tx_buf++ : 0;

@@ -175,8 +204,8 @@ static int sun4i_spi_transfer_one(struct spi_master *master,
 	int ret = 0;
 	u32 reg;
 
-	/* We don't support transfer larger than the FIFO */
-	if (tfr->len > SUN4I_FIFO_DEPTH)
+	/* This is the maximum SPI burst size supported by the hardware */
+	if (tfr->len > SUN4I_MAX_XFER_SIZE)
 		return -EINVAL;
 
 	reinit_completion(&sspi->done);

@@ -274,7 +303,10 @@ static int sun4i_spi_transfer_one(struct spi_master *master,
 	sun4i_spi_fill_fifo(sspi, SUN4I_FIFO_DEPTH);
 
 	/* Enable the interrupts */
-	sun4i_spi_write(sspi, SUN4I_INT_CTL_REG, SUN4I_INT_CTL_TC);
+	sun4i_spi_enable_interrupt(sspi, SUN4I_INT_CTL_TC | SUN4I_INT_CTL_RF_F34);
+	/* Only enable Tx FIFO interrupt if we really need it */
+	if (tx_len > SUN4I_FIFO_DEPTH)
+		sun4i_spi_enable_interrupt(sspi, SUN4I_INT_CTL_TF_E34);
 
 	/* Start the transfer */
 	reg = sun4i_spi_read(sspi, SUN4I_CTL_REG);

@@ -287,8 +319,6 @@ static int sun4i_spi_transfer_one(struct spi_master *master,
 		goto out;
 	}
 
-	sun4i_spi_drain_fifo(sspi, SUN4I_FIFO_DEPTH);
-
 out:
 	sun4i_spi_write(sspi, SUN4I_INT_CTL_REG, 0);
 

@@ -303,10 +333,33 @@ static irqreturn_t sun4i_spi_handler(int irq, void *dev_id)
 	/* Transfer complete */
 	if (status & SUN4I_INT_CTL_TC) {
 		sun4i_spi_write(sspi, SUN4I_INT_STA_REG, SUN4I_INT_CTL_TC);
+		sun4i_spi_drain_fifo(sspi, SUN4I_FIFO_DEPTH);
 		complete(&sspi->done);
 		return IRQ_HANDLED;
 	}
 
+	/* Receive FIFO 3/4 full */
+	if (status & SUN4I_INT_CTL_RF_F34) {
+		sun4i_spi_drain_fifo(sspi, SUN4I_FIFO_DEPTH);
+		/* Only clear the interrupt _after_ draining the FIFO */
+		sun4i_spi_write(sspi, SUN4I_INT_STA_REG, SUN4I_INT_CTL_RF_F34);
+		return IRQ_HANDLED;
+	}
+
+	/* Transmit FIFO 3/4 empty */
+	if (status & SUN4I_INT_CTL_TF_E34) {
+		sun4i_spi_fill_fifo(sspi, SUN4I_FIFO_DEPTH);
+
+		if (!sspi->len)
+			/* nothing left to transmit */
+			sun4i_spi_disable_interrupt(sspi, SUN4I_INT_CTL_TF_E34);
+
+		/* Only clear the interrupt _after_ re-seeding the FIFO */
+		sun4i_spi_write(sspi, SUN4I_INT_STA_REG, SUN4I_INT_CTL_TF_E34);
+
+		return IRQ_HANDLED;
+	}
+
 	return IRQ_NONE;
 }

--
1.8.5.3

#8 lore raw

PATCH v5 1/1 ARM: sun4i: spi: Allow transfers larger than FIFO size

Quoted 11 lines · Alexandru Gagniuc

SPI transfers were limited to one FIFO depth, which is 64 bytes. This was an artificial limitation, however, as the hardware can handle much larger bursts. To accommodate this, we enable the interrupt when the Rx FIFO is 3/4 full, and drain the FIFO within the interrupt handler. The 3/4 ratio was chosen arbitrarily, with the intention to reduce the potential number of interrupts.

Since the SUN4I_CTL_TP bit is set, the hardware will pause transmission whenever the FIFO is full, so there is no risk of losing data if we can't service the interrupt in time.

Quoted 8 lines

For the Tx side, enable and use the Tx FIFO 3/4 empty interrupt to replenish the FIFO on large SPI bursts. This requires more care in when the interrupt is left enabled, as this interrupt will continually trigger when the FIFO is less than 1/4 full, even though we acknowledge it.

Signed-off-by Alexandru Gagniuc <[email protected]>
Acked-by Maxime Ripard <[email protected]>

Hmmm, you forgot to Cc Mark Brown. Please resubmit it Ccing whoever shows up using get_maintainer, otherwise, your patch won't be applied.

You also forgot the changes between this version and the previous one.

Thanks!
Maxime

Signature · 10 lines
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 836 bytes
Desc: Digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20140401/6d6755ec/attachment.sig>
author
#9 lore raw

PATCH RESEND v5 1/1 ARM: sun4i: spi: Allow transfers larger than FIFO size

SPI transfers were limited to one FIFO depth, which is 64 bytes. This was an artificial limitation, however, as the hardware can handle much larger bursts. To accommodate this, we enable the interrupt when the Rx FIFO is 3/4 full, and drain the FIFO within the interrupt handler. The 3/4 ratio was chosen arbitrarily, with the intention to reduce the potential number of interrupts.

Since the SUN4I_CTL_TP bit is set, the hardware will pause transmission whenever the FIFO is full, so there is no risk of losing data if we can't service the interrupt in time.

For the Tx side, enable and use the Tx FIFO 3/4 empty interrupt to replenish the FIFO on large SPI bursts. This requires more care in when the interrupt is left enabled, as this interrupt will continually trigger when the FIFO is less than 1/4 full, even though we acknowledge it.

Signed-off-by Alexandru Gagniuc <[email protected]>
Acked-by Maxime Ripard <[email protected]>

---

Changes from v4:
* use min3() instead of two if statements in sun4i_spi_fill_fifo()
* fix trivial whitespace issue in if statement in sun4i_spi_handler()
* use consistent style in assigning 'reg' in the added functions.

 drivers/spi/spi-sun4i.c | 71 ++++++++++++++++++++++++++++++++++++++++++-------
 1 file changed, 62 insertions(+), 9 deletions(-)
drivers/spi/spi-sun4i.c +62 -9
index 3f82705..d80ceba 100644
@@ -47,6 +47,8 @@
 #define SUN4I_CTL_TP				BIT(18)
 
 #define SUN4I_INT_CTL_REG		0x0c
+#define SUN4I_INT_CTL_RF_F34			BIT(4)
+#define SUN4I_INT_CTL_TF_E34			BIT(12)
 #define SUN4I_INT_CTL_TC			BIT(16)
 
 #define SUN4I_INT_STA_REG		0x10

@@ -62,11 +64,14 @@
 #define SUN4I_CLK_CTL_CDR1(div)			(((div) & SUN4I_CLK_CTL_CDR1_MASK) << 8)
 #define SUN4I_CLK_CTL_DRS			BIT(12)
 
+#define SUN4I_MAX_XFER_SIZE			0xffffff
+
 #define SUN4I_BURST_CNT_REG		0x20
-#define SUN4I_BURST_CNT(cnt)			((cnt) & 0xffffff)
+#define SUN4I_BURST_CNT(cnt)			((cnt) & SUN4I_MAX_XFER_SIZE)
 
 #define SUN4I_XMIT_CNT_REG		0x24
-#define SUN4I_XMIT_CNT(cnt)			((cnt) & 0xffffff)
+#define SUN4I_XMIT_CNT(cnt)			((cnt) & SUN4I_MAX_XFER_SIZE)
+
 
 #define SUN4I_FIFO_STA_REG		0x28
 #define SUN4I_FIFO_STA_RF_CNT_MASK		0x7f

@@ -97,6 +102,27 @@ static inline void sun4i_spi_write(struct sun4i_spi *sspi, u32 reg, u32 value)
 	writel(value, sspi->base_addr + reg);
 }
 
+static inline u32 sun4i_spi_get_tx_fifo_count(struct sun4i_spi *sspi)
+{
+	u32 reg = sun4i_spi_read(sspi, SUN4I_FIFO_STA_REG);
+	reg >>= SUN4I_FIFO_STA_TF_CNT_BITS;
+	return reg & SUN4I_FIFO_STA_TF_CNT_MASK;
+}
+
+static inline void sun4i_spi_enable_interrupt(struct sun4i_spi *sspi, u32 mask)
+{
+	u32 reg = sun4i_spi_read(sspi, SUN4I_INT_CTL_REG);
+	reg |= mask;
+	sun4i_spi_write(sspi, SUN4I_INT_CTL_REG, reg);
+}
+
+static inline void sun4i_spi_disable_interrupt(struct sun4i_spi *sspi, u32 mask)
+{
+	u32 reg = sun4i_spi_read(sspi, SUN4I_INT_CTL_REG);
+	reg &= ~mask;
+	sun4i_spi_write(sspi, SUN4I_INT_CTL_REG, reg);
+}
+
 static inline void sun4i_spi_drain_fifo(struct sun4i_spi *sspi, int len)
 {
 	u32 reg, cnt;

@@ -119,10 +145,13 @@ static inline void sun4i_spi_drain_fifo(struct sun4i_spi *sspi, int len)
 
 static inline void sun4i_spi_fill_fifo(struct sun4i_spi *sspi, int len)
 {
+	u32 cnt;
 	u8 byte;
 
-	if (len > sspi->len)
-		len = sspi->len;
+	/* See how much data we can fit */
+	cnt = SUN4I_FIFO_DEPTH - sun4i_spi_get_tx_fifo_count(sspi);
+
+	len = min3(len, (int)cnt, sspi->len);
 
 	while (len--) {
 		byte = sspi->tx_buf ? *sspi->tx_buf++ : 0;

@@ -175,8 +204,8 @@ static int sun4i_spi_transfer_one(struct spi_master *master,
 	int ret = 0;
 	u32 reg;
 
-	/* We don't support transfer larger than the FIFO */
-	if (tfr->len > SUN4I_FIFO_DEPTH)
+	/* This is the maximum SPI burst size supported by the hardware */
+	if (tfr->len > SUN4I_MAX_XFER_SIZE)
 		return -EINVAL;
 
 	reinit_completion(&sspi->done);

@@ -274,7 +303,10 @@ static int sun4i_spi_transfer_one(struct spi_master *master,
 	sun4i_spi_fill_fifo(sspi, SUN4I_FIFO_DEPTH);
 
 	/* Enable the interrupts */
-	sun4i_spi_write(sspi, SUN4I_INT_CTL_REG, SUN4I_INT_CTL_TC);
+	sun4i_spi_enable_interrupt(sspi, SUN4I_INT_CTL_TC | SUN4I_INT_CTL_RF_F34);
+	/* Only enable Tx FIFO interrupt if we really need it */
+	if (tx_len > SUN4I_FIFO_DEPTH)
+		sun4i_spi_enable_interrupt(sspi, SUN4I_INT_CTL_TF_E34);
 
 	/* Start the transfer */
 	reg = sun4i_spi_read(sspi, SUN4I_CTL_REG);

@@ -287,8 +319,6 @@ static int sun4i_spi_transfer_one(struct spi_master *master,
 		goto out;
 	}
 
-	sun4i_spi_drain_fifo(sspi, SUN4I_FIFO_DEPTH);
-
 out:
 	sun4i_spi_write(sspi, SUN4I_INT_CTL_REG, 0);
 

@@ -303,10 +333,33 @@ static irqreturn_t sun4i_spi_handler(int irq, void *dev_id)
 	/* Transfer complete */
 	if (status & SUN4I_INT_CTL_TC) {
 		sun4i_spi_write(sspi, SUN4I_INT_STA_REG, SUN4I_INT_CTL_TC);
+		sun4i_spi_drain_fifo(sspi, SUN4I_FIFO_DEPTH);
 		complete(&sspi->done);
 		return IRQ_HANDLED;
 	}
 
+	/* Receive FIFO 3/4 full */
+	if (status & SUN4I_INT_CTL_RF_F34) {
+		sun4i_spi_drain_fifo(sspi, SUN4I_FIFO_DEPTH);
+		/* Only clear the interrupt _after_ draining the FIFO */
+		sun4i_spi_write(sspi, SUN4I_INT_STA_REG, SUN4I_INT_CTL_RF_F34);
+		return IRQ_HANDLED;
+	}
+
+	/* Transmit FIFO 3/4 empty */
+	if (status & SUN4I_INT_CTL_TF_E34) {
+		sun4i_spi_fill_fifo(sspi, SUN4I_FIFO_DEPTH);
+
+		if (!sspi->len)
+			/* nothing left to transmit */
+			sun4i_spi_disable_interrupt(sspi, SUN4I_INT_CTL_TF_E34);
+
+		/* Only clear the interrupt _after_ re-seeding the FIFO */
+		sun4i_spi_write(sspi, SUN4I_INT_STA_REG, SUN4I_INT_CTL_TF_E34);
+
+		return IRQ_HANDLED;
+	}
+
 	return IRQ_NONE;
 }

--
1.8.5.3