Skip to contentSkip to conversation

drm/i915/bdw: Set initial rps freq to RP1

PATCH In review Ben Widawsky 2 participants 4 messages Apr 1, 2014

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

PATCH 1/4 drm/i915/bdw: Set initial rps freq to RP1

Programming it outside of the rp0-rp1 range is considered a programming error. Since we do not know that the previous value would actually be in the range, program something we've read from the hardware, and therefore know will work.

This is potentially an issue for platforms whose ranges are outside the norms given in the programming guide (ie. early silicon)

v2: Use RP1 instead of RPn

---
 drivers/gpu/drm/i915/intel_pm.c | 6 ++++--
 1 file changed, 4 insertions(+), 2 deletions(-)
drivers/gpu/drm/i915/intel_pm.c +4 -2
index e9a9aef..51ff40e 100644
@@ -3284,8 +3284,10 @@ static void gen8_enable_rps(struct drm_device *dev)
 				    rc6_mask);
 
 	/* 4 Program defaults and thresholds for RPS*/
-	I915_WRITE(GEN6_RPNSWREQ, HSW_FREQUENCY(10)); /* Request 500 MHz */
-	I915_WRITE(GEN6_RC_VIDEO_FREQ, HSW_FREQUENCY(12)); /* Request 600 MHz */
+	I915_WRITE(GEN6_RPNSWREQ,
+		   HSW_FREQUENCY(dev_priv->rps.rp1_freq));
+	I915_WRITE(GEN6_RC_VIDEO_FREQ,
+		   HSW_FREQUENCY(dev_priv->rps.rp1_freq));
 	/* NB: Docs say 1s, and 1000000 - which aren't equivalent */
 	I915_WRITE(GEN6_RP_DOWN_TIMEOUT, 100000000 / 128); /* 1 second timeout */
 
Signature · 1 line
1.9.1
#1 lore raw

PATCH 2/4 drm/i915/bdw: Extract rp_state_caps logic

We have a need for duplicated parsing of the RP_STATE_CAPS register (and the setting of the associated fields). To reuse some code, we can extract the function into a simple helper.

This patch also addresses the fact that we missed doing this for gen8, something we should have done anyway.

This could be two patches, one to extract, and one to add gen8, but it's trivial enough that I think one is fine. I will accept a request to split it. Please notice the fix addressed by v2 below.

Valleyview is left untouched because it is different.

v2: Logically rebased on top of
commit dd0a1aa19bd3d7203e58157b84cea78bbac605ac

Author: Jeff McGee <[email protected]>
Date:   Tue Feb 4 11:32:31 2014 -0600

drm/i915: Restore rps/rc6 on reset

Note with the above change the fix for gen8 is also handled (which was not the case in Jeff's original patch).

---
 drivers/gpu/drm/i915/intel_pm.c | 40 +++++++++++++++++++++++-----------------
 1 file changed, 23 insertions(+), 17 deletions(-)
drivers/gpu/drm/i915/intel_pm.c +23 -17
index 51ff40e..ed45143 100644
@@ -3247,6 +3247,27 @@ static void gen6_enable_rps_interrupts(struct drm_device *dev)
 	spin_unlock_irq(&dev_priv->irq_lock);
 }
 
+static void parse_rp_state_cap(struct drm_i915_private *dev_priv, u32 rp_state_cap)
+{
+	/* All of these values are in units of 50MHz */
+	dev_priv->rps.cur_freq		= 0;
+	/* static values from HW: RP0 < RPe < RP1 < RPn (min_freq) */
+	dev_priv->rps.rp1_freq		= (rp_state_cap >>  8) & 0xff;
+	dev_priv->rps.rp0_freq		= (rp_state_cap >>  0) & 0xff;
+	dev_priv->rps.min_freq		= (rp_state_cap >> 16) & 0xff;
+	/* XXX: only BYT has a special efficient freq */
+	dev_priv->rps.efficient_freq	= dev_priv->rps.rp1_freq;
+	/* hw_max = RP0 until we check for overclocking */
+	dev_priv->rps.max_freq		= dev_priv->rps.rp0_freq;
+
+	/* Preserve min/max settings in case of re-init */
+	if (dev_priv->rps.max_freq_softlimit == 0)
+		dev_priv->rps.max_freq_softlimit = dev_priv->rps.max_freq;
+
+	if (dev_priv->rps.min_freq_softlimit == 0)
+		dev_priv->rps.min_freq_softlimit = dev_priv->rps.min_freq;
+}
+
 static void gen8_enable_rps(struct drm_device *dev)
 {
 	struct drm_i915_private *dev_priv = dev->dev_private;
@@ -3265,6 +3286,7 @@ static void gen8_enable_rps(struct drm_device *dev)
 	I915_WRITE(GEN6_RC_CONTROL, 0);
 
 	rp_state_cap = I915_READ(GEN6_RP_STATE_CAP);
+	parse_rp_state_cap(dev_priv, rp_state_cap);
 
 	/* 2b: Program RC6 thresholds.*/
 	I915_WRITE(GEN6_RC6_WAKE_RATE_LIMIT, 40 << 16);
@@ -3353,23 +3375,7 @@ static void gen6_enable_rps(struct drm_device *dev)
 	rp_state_cap = I915_READ(GEN6_RP_STATE_CAP);
 	gt_perf_status = I915_READ(GEN6_GT_PERF_STATUS);
 
-	/* All of these values are in units of 50MHz */
-	dev_priv->rps.cur_freq		= 0;
-	/* static values from HW: RP0 < RPe < RP1 < RPn (min_freq) */
-	dev_priv->rps.rp1_freq		= (rp_state_cap >>  8) & 0xff;
-	dev_priv->rps.rp0_freq		= (rp_state_cap >>  0) & 0xff;
-	dev_priv->rps.min_freq		= (rp_state_cap >> 16) & 0xff;
-	/* XXX: only BYT has a special efficient freq */
-	dev_priv->rps.efficient_freq	= dev_priv->rps.rp1_freq;
-	/* hw_max = RP0 until we check for overclocking */
-	dev_priv->rps.max_freq		= dev_priv->rps.rp0_freq;
-
-	/* Preserve min/max settings in case of re-init */
-	if (dev_priv->rps.max_freq_softlimit == 0)
-		dev_priv->rps.max_freq_softlimit = dev_priv->rps.max_freq;
-
-	if (dev_priv->rps.min_freq_softlimit == 0)
-		dev_priv->rps.min_freq_softlimit = dev_priv->rps.min_freq;
+	parse_rp_state_cap(dev_priv, rp_state_cap);
 
 	/* disable the counters and set deterministic thresholds */
 	I915_WRITE(GEN6_RC_CONTROL, 0);
Signature · 1 line
1.9.1
#2 lore raw

PATCH 3/4 drm/i915/bdw: RPS frequency bits are the same as HSW

In reply to Ben Widawsky
---
 drivers/gpu/drm/i915/intel_pm.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/gpu/drm/i915/intel_pm.c +1 -1
index ed45143..9728c2c 100644
@@ -3041,7 +3041,7 @@ void gen6_set_rps(struct drm_device *dev, u8 val)
 	if (val != dev_priv->rps.cur_freq) {
 		gen6_set_rps_thresholds(dev_priv, val);
 
-		if (IS_HASWELL(dev))
+		if (IS_HASWELL(dev) || IS_BROADWELL(dev))
 			I915_WRITE(GEN6_RPNSWREQ,
 				   HSW_FREQUENCY(val));
 		else
Signature · 1 line
1.9.1