v4l2: add new V4L2_PIX_FMT_RGB666 pixel format.
Subsystems (10)
PATCH v12 1/12 v4l2: add new V4L2_PIX_FMT_RGB666 pixel format.
That new macro is needed by the imx_drm staging driver
for supporting the QVGA display of the eukrea-cpuimx51 board.
---
ChangeLog v9->v10:
- Rebased on top of:
"211e7f2 [media] DocBook media: drop the old incorrect packed RGB table"
- Added Philipp Zabel's Ack.
ChangeLog v8->v9:
- Removed the Cc. They are now set in git-send-email directly.
ChangeLog v7->v8:
- Added Mauro Carvalho Chehab back to the list of Cc
ChangeLog v6->v7:
- Shrinked even more the Cc list.
ChangeLog v5->v6:
- Remove people not concerned by this patch from the Cc list.
ChangeLog v3->v4:
- Added Laurent Pinchart's Ack.
ChangeLog v2->v3:
- Added some interested people in the Cc list.
- Added Mauro Carvalho Chehab's Ack.
- Added documentation.
--- .../DocBook/media/v4l/pixfmt-packed-rgb.xml | 39 ++++++++++++++++++++ include/uapi/linux/videodev2.h | 1 + 2 files changed, 40 insertions(+)
Documentation/DocBook/media/v4l/pixfmt-packed-rgb.xml +39 -0
@@ -279,6 +279,45 @@ colorspace <constant>V4L2_COLORSPACE_SRGB</constant>.</para> <entry></entry> <entry></entry> </row> + <row id="V4L2-PIX-FMT-RGB666"> + <entry><constant>V4L2_PIX_FMT_RGB666</constant></entry> + <entry>'RGBH'</entry> + <entry></entry> + <entry>r<subscript>5</subscript></entry> + <entry>r<subscript>4</subscript></entry> + <entry>r<subscript>3</subscript></entry> + <entry>r<subscript>2</subscript></entry> + <entry>r<subscript>1</subscript></entry> + <entry>r<subscript>0</subscript></entry> + <entry>g<subscript>5</subscript></entry> + <entry>g<subscript>4</subscript></entry> + <entry></entry> + <entry>g<subscript>3</subscript></entry> + <entry>g<subscript>2</subscript></entry> + <entry>g<subscript>1</subscript></entry> + <entry>g<subscript>0</subscript></entry> + <entry>b<subscript>5</subscript></entry> + <entry>b<subscript>4</subscript></entry> + <entry>b<subscript>3</subscript></entry> + <entry>b<subscript>2</subscript></entry> + <entry></entry> + <entry>b<subscript>1</subscript></entry> + <entry>b<subscript>0</subscript></entry> + <entry></entry> + <entry></entry> + <entry></entry> + <entry></entry> + <entry></entry> + <entry></entry> + <entry></entry> + <entry></entry> + <entry></entry> + <entry></entry> + <entry></entry> + <entry></entry> + <entry></entry> + <entry></entry> + </row> <row id="V4L2-PIX-FMT-BGR24"> <entry><constant>V4L2_PIX_FMT_BGR24</constant></entry> <entry>'BGR3'</entry>
include/uapi/linux/videodev2.h +1 -0
@@ -299,6 +299,7 @@ struct v4l2_pix_format {#define V4L2_PIX_FMT_RGB555X v4l2_fourcc('R', 'G', 'B', 'Q')/* 16 RGB-5-5-5 BE */ #define V4L2_PIX_FMT_RGB565X v4l2_fourcc('R', 'G', 'B', 'R')/* 16 RGB-5-6-5 BE */ #define V4L2_PIX_FMT_BGR666 v4l2_fourcc('B', 'G', 'R', 'H')/* 18 BGR-6-6-6 */ +#define V4L2_PIX_FMT_RGB666 v4l2_fourcc('R', 'G', 'B', 'H')/* 18 RGB-6-6-6 */ #define V4L2_PIX_FMT_BGR24 v4l2_fourcc('B', 'G', 'R', '3')/* 24 BGR-8-8-8 */ #define V4L2_PIX_FMT_RGB24 v4l2_fourcc('R', 'G', 'B', '3')/* 24 RGB-8-8-8 */ #define V4L2_PIX_FMT_BGR32 v4l2_fourcc('B', 'G', 'R', '4')/* 32 BGR-8-8-8-8 */
Signature · 1 line
1.7.9.5
PATCH v12 2/12 imx-drm: Add RGB666 support for parallel display.
---
ChangeLog v8->v9:
- Rebased.
- Added Philipp Zabel's ack.
- Shortened the patch title.
ChangeLog v8->v9:
- Removed the Cc. They are now set in git-send-email directly.
- Rebased.
ChangeLog v7->v8:
- Shrinked even more the Cc list.
ChangeLog v6->v7:
- Shrinked even more the Cc list.
ChangeLog v5->v6:
- Remove people not concerned by this patch from the Cc list.
ChangeLog v3->v5:
- Use the correct RGB order.
ChangeLog v2->v3:
- Added some interested people in the Cc list.
- Removed the commit message long desciption that was just a copy of the short description.
- Rebased the patch.
- Fixed a copy-paste error in the ipu_dc_map_clear parameter.
--- .../bindings/staging/imx-drm/fsl-imx-drm.txt | 3 ++- drivers/staging/imx-drm/ipu-v3/ipu-dc.c | 9 +++++++++ drivers/staging/imx-drm/parallel-display.c | 2 ++ 3 files changed, 13 insertions(+), 1 deletion(-)
Documentation/devicetree/bindings/staging/imx-drm/fsl-imx-drm.txt +2 -1
@@ -60,7 +60,8 @@ Required properties: - compatible: Should be "fsl,imx-parallel-display" Optional properties: - interface_pix_fmt: How this display is connected to the - display interface. Currently supported types: "rgb24", "rgb565", "bgr666" + display interface. Currently supported types: "rgb24", "rgb565", "bgr666", + "rgb666" - edid: verbatim EDID data block describing attached display. - ddc: phandle describing the i2c bus handling the display data channel
drivers/staging/imx-drm/ipu-v3/ipu-dc.c +9 -0
@@ -92,6 +92,7 @@ enum ipu_dc_map {IPU_DC_MAP_GBR24 ,/* TVEv2 */ IPU_DC_MAP_BGR666 ,IPU_DC_MAP_BGR24 , + IPU_DC_MAP_RGB666, }; struct ipu_dc {
@@ -155,6 +156,8 @@ static int ipu_pixfmt_to_map(u32 fmt)return IPU_DC_MAP_BGR666 ;case V4L2_PIX_FMT_BGR24 :return IPU_DC_MAP_BGR24 ; +case V4L2_PIX_FMT_RGB666 : +return IPU_DC_MAP_RGB666 ;default :return -EINVAL ; }
@@ -404,6 +407,12 @@ int ipu_dc_init(struct ipu_soc *ipu, struct device *dev,ipu_dc_map_config (priv,IPU_DC_MAP_BGR24 ,1 ,15 ,0xff );/* green */ ipu_dc_map_config (priv,IPU_DC_MAP_BGR24 ,0 ,23 ,0xff );/* blue */ +/* rgb666 */ +ipu_dc_map_clear (priv,IPU_DC_MAP_RGB666 ); +ipu_dc_map_config (priv,IPU_DC_MAP_RGB666 ,0 ,5 ,0xfc );/* blue */ +ipu_dc_map_config (priv,IPU_DC_MAP_RGB666 ,1 ,11 ,0xfc );/* green */ +ipu_dc_map_config (priv,IPU_DC_MAP_RGB666 ,2 ,17 ,0xfc );/* red */ +return 0 ; }
drivers/staging/imx-drm/parallel-display.c +2 -0
@@ -219,6 +219,8 @@ static int imx_pd_bind(struct device *dev, struct device *master, void *data) imxpd->interface_pix_fmt =V4L2_PIX_FMT_RGB565 ; else if (!strcmp(fmt, "bgr666")) imxpd->interface_pix_fmt =V4L2_PIX_FMT_BGR666 ; + else if (!strcmp(fmt, "rgb666")) + imxpd->interface_pix_fmt =V4L2_PIX_FMT_RGB666 ; } panel_node =of_parse_phandle (np,"fsl,panel" ,0 );
Signature · 1 line
1.7.9.5
PATCH v12 3/12 imx-drm: Correct BGR666 and the board's dts that use them.
In reply to Denis CarikliThe current BGR666 is not consistent with the other color mapings like BGR24. BGR666 should be in the same byte order than BGR24.
---
ChangeLog v9->v10:
- Rebased.
- Added Philipp Zabel's Ack.
- Included Lothar Waßmann's suggestion about imx-ldb.c.
- Shortened the patch title
ChangeLog v8->v9:
- Removed the Cc. They are now set in git-send-email directly.
ChangeLog v7->v8:
- Shrinked even more the Cc list.
ChangeLog v6->v7:
- Shrinked even more the Cc list.
ChangeLog v5->v6:
- Remove people not concerned by this patch from the Cc list.
- Added a better explanation of the change.
ChangeLog v5:
- New patch.
--- arch/arm/boot/dts/imx51-apf51dev.dts | 2 +- arch/arm/boot/dts/imx53-m53evk.dts | 2 +- drivers/staging/imx-drm/imx-ldb.c | 4 ++-- drivers/staging/imx-drm/ipu-v3/ipu-dc.c | 4 ++-- 4 files changed, 6 insertions(+), 6 deletions(-)
arch/arm/boot/dts/imx51-apf51dev.dts +1 -1
@@ -18,7 +18,7 @@ display@di1 { compatible = "fsl,imx-parallel-display"; - interface-pix-fmt = "bgr666"; + interface-pix-fmt = "rgb666"; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_ipu_disp1>;
arch/arm/boot/dts/imx53-m53evk.dts +1 -1
@@ -24,7 +24,7 @@ soc { display1: display@di1 { compatible = "fsl,imx-parallel-display"; - interface-pix-fmt = "bgr666"; + interface-pix-fmt = "rgb666"; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_ipu_disp1>;
drivers/staging/imx-drm/imx-ldb.c +2 -2
@@ -188,11 +188,11 @@ static void imx_ldb_encoder_prepare(struct drm_encoder *encoder)switch (imx_ldb_ch->chno) {case 0 : pixel_fmt = (ldb->ldb_ctrl &LDB_DATA_WIDTH_CH0_24 ) ? -V4L2_PIX_FMT_RGB24 :V4L2_PIX_FMT_BGR666 ; +V4L2_PIX_FMT_RGB24 :V4L2_PIX_FMT_RGB666 ;break ;case 1 : pixel_fmt = (ldb->ldb_ctrl &LDB_DATA_WIDTH_CH1_24 ) ? -V4L2_PIX_FMT_RGB24 :V4L2_PIX_FMT_BGR666 ; +V4L2_PIX_FMT_RGB24 :V4L2_PIX_FMT_RGB666 ;break ;default : dev_err(ldb->dev, "unable to config di%d panel format\n",
drivers/staging/imx-drm/ipu-v3/ipu-dc.c +2 -2
@@ -397,9 +397,9 @@ int ipu_dc_init(struct ipu_soc *ipu, struct device *dev,/* bgr666 */ ipu_dc_map_clear (priv,IPU_DC_MAP_BGR666 ); -ipu_dc_map_config (priv,IPU_DC_MAP_BGR666 ,0 ,5 ,0xfc );/* blue */ +ipu_dc_map_config (priv,IPU_DC_MAP_BGR666 ,0 ,17 ,0xfc );/* blue */ ipu_dc_map_config (priv,IPU_DC_MAP_BGR666 ,1 ,11 ,0xfc );/* green */ -ipu_dc_map_config (priv,IPU_DC_MAP_BGR666 ,2 ,17 ,0xfc );/* red */ +ipu_dc_map_config (priv,IPU_DC_MAP_BGR666 ,2 ,5 ,0xfc );/* red */ /* bgr24 */ ipu_dc_map_clear (priv,IPU_DC_MAP_BGR24 );
Signature · 1 line
1.7.9.5
Re: [PATCH v12][ 03/12] imx-drm: Correct BGR666 and the board's dts that use them.
Quoted 16 lines · Denis Carikli
arch/arm/boot/dts/imx51-apf51dev.dts | 2 +- arch/arm/boot/dts/imx53-m53evk.dts | 2 +- drivers/staging/imx-drm/imx-ldb.c | 4 ++-- drivers/staging/imx-drm/ipu-v3/ipu-dc.c | 4 ++-- 4 files changed, 6 insertions(+), 6 deletions(-)arch/arm/boot/dts/imx51-apf51dev.dts +1
-1@@ -18,7 +18,7 @@ display@di1 { compatible = "fsl,imx-parallel-display"; - interface-pix-fmt = "bgr666"; + interface-pix-fmt = "rgb666";
...
arch/arm/boot/dts/imx51-apf51dev.dts
Quoted 7 lines
arch/arm/boot/dts/imx51-apf51dev.dts +2
-2/* bgr666 */ ipu_dc_map_clear(priv, IPU_DC_MAP_BGR666); - ipu_dc_map_config(priv, IPU_DC_MAP_BGR666, 0, 5, 0xfc); /* blue */ + ipu_dc_map_config(priv, IPU_DC_MAP_BGR666, 0, 17, 0xfc); /* blue */ ipu_dc_map_config(priv, IPU_DC_MAP_BGR666, 1, 11, 0xfc); /* green */ - ipu_dc_map_config(priv, IPU_DC_MAP_BGR666, 2, 17, 0xfc); /* red */ + ipu_dc_map_config(priv, IPU_DC_MAP_BGR666, 2, 5, 0xfc); /* red */
arm-soc people have become very obtuse with respect to changes to any patches to arch/arm/boot/dts, and complain loudly if any changes to that directory do not go through them as separate patches.
What this means is that your patch is unacceptable and needs to be split up.
The choices seem to be to either break imx-drm by splitting the patch in two, thereby ending up with the two dependent changes being merged entirely separate, resulting in breakage while one or other is merged, or to add the RGB666 support, wait for that to hit mainline, then update the DT files, wait for that to hit mainline, then fix the BGR666 support. That'll take around six to nine months (two to three months per release cycle.)
Or arm-soc could come to their senses and realise that they do not have sole ownership over arch/arm/boot/dts.
Signature · 2 lines
FTTC broadband for 0.8mile line: now at 9.7Mbps down 460kbps up... slowly improving, and getting towards what was expected from it.
PATCH v12 4/12 imx-drm: Match ipu_di_signal_cfg's clk_pol with its description.
In reply to Denis CarikliAccording to the datasheet, setting the di0_polarity_disp_clk field in the GENERAL di register sets the output clock polarity to active high.
---
ChangeLog v9->v10:
- New patch that is now needed by the
"staging: imx-drm: Use de-active and pixelclk-active" patch.
--- drivers/staging/imx-drm/ipu-v3/ipu-di.c | 2 +- drivers/staging/imx-drm/ipuv3-crtc.c | 2 +- 2 files changed, 2 insertions(+), 2 deletions(-)
drivers/staging/imx-drm/ipu-v3/ipu-di.c +1 -1
@@ -595,7 +595,7 @@ int ipu_di_init_sync_panel(struct ipu_di *di, struct ipu_di_signal_cfg *sig) } } -if (!sig->clk_pol) +if (sig->clk_pol) di_gen |=DI_GEN_POLARITY_DISP_CLK ;ipu_di_write (di, di_gen,DI_GENERAL );
drivers/staging/imx-drm/ipuv3-crtc.c +1 -1
@@ -158,7 +158,7 @@ static int ipu_crtc_mode_set(struct drm_crtc *crtc, sig_cfg.Vsync_pol =1 ; sig_cfg.enable_pol =1 ; - sig_cfg.clk_pol =1 ; + sig_cfg.clk_pol =0 ; sig_cfg.width = mode->hdisplay; sig_cfg.height = mode->vdisplay; sig_cfg.pixel_fmt = out_pixel_fmt;
Signature · 1 line
1.7.9.5
PATCH v12 5/12 imx-drm: use defines for clock polarity settings
In reply to Denis Carikli---
ChangeLog 11->v12:
- Improved the define names to match the hardware:
ENABLE_POL is not a clock signal but instead an enable signal.
ChangeLog v9->v10:
- New patch which was splitted out from:
"staging: imx-drm: Use de-active and pixelclk-active display-timings.".
- Fixes many issues in "staging: imx-drm: Use de-active and pixelclk-active display-timings.":
- More clear meaning of the polarity settings.
- The SET_CLK_POL and SET_DE_POL masks are not
needed anymore.
--- drivers/staging/imx-drm/ipu-v3/imx-ipu-v3.h | 8 +++++++- drivers/staging/imx-drm/ipu-v3/ipu-di.c | 4 ++-- drivers/staging/imx-drm/ipuv3-crtc.c | 4 ++-- 3 files changed, 11 insertions(+), 5 deletions(-)
drivers/staging/imx-drm/ipu-v3/imx-ipu-v3.h +7 -1
@@ -27,6 +27,12 @@ enum ipuv3_type {#define IPU_PIX_FMT_GBR24 v4l2_fourcc('G', 'B', 'R', '3') +#define CLK_POL_NEGEDGE 0 +#define CLK_POL_POSEDGE 1 + +#define ENABLE_POL_LOW 0 +#define ENABLE_POL_HIGH 1 +/* * Bitfield of Display Interface signal polarities. */
@@ -37,7 +43,7 @@ struct ipu_di_signal_cfg { unsigned clksel_en:1; unsigned clkidle_en:1; unsigned data_pol:1; /* true = inverted */ - unsigned clk_pol:1; /* true = rising edge */ + unsigned clk_pol:1; unsigned enable_pol:1; unsigned Hsync_pol:1; /* true = active high */ unsigned Vsync_pol:1;
drivers/staging/imx-drm/ipu-v3/ipu-di.c +2 -2
@@ -595,7 +595,7 @@ int ipu_di_init_sync_panel(struct ipu_di *di, struct ipu_di_signal_cfg *sig) } } -if (sig->clk_pol) +if (sig->clk_pol ==CLK_POL_POSEDGE ) di_gen |=DI_GEN_POLARITY_DISP_CLK ;ipu_di_write (di, di_gen,DI_GENERAL );
@@ -606,7 +606,7 @@ int ipu_di_init_sync_panel(struct ipu_di *di, struct ipu_di_signal_cfg *sig) reg =ipu_di_read (di,DI_POL ); reg &= ~(DI_POL_DRDY_DATA_POLARITY |DI_POL_DRDY_POLARITY_15 ); -if (sig->enable_pol) +if (sig->enable_pol ==ENABLE_POL_HIGH ) reg |=DI_POL_DRDY_POLARITY_15 ;if (sig->data_pol) reg |=DI_POL_DRDY_DATA_POLARITY ;
drivers/staging/imx-drm/ipuv3-crtc.c +2 -2
@@ -157,8 +157,8 @@ static int ipu_crtc_mode_set(struct drm_crtc *crtc,if (mode->flags &DRM_MODE_FLAG_PVSYNC ) sig_cfg.Vsync_pol =1 ; - sig_cfg.enable_pol =1 ; - sig_cfg.clk_pol =0 ; + sig_cfg.enable_pol =ENABLE_POL_HIGH ; + sig_cfg.clk_pol =CLK_POL_NEGEDGE ; sig_cfg.width = mode->hdisplay; sig_cfg.height = mode->vdisplay; sig_cfg.pixel_fmt = out_pixel_fmt;
Signature · 1 line
1.7.9.5
PATCH v12 6/12 ARM: dts: imx5*, imx6*: correct display-timings nodes.
In reply to Denis CarikliThe imx-drm driver can't use the de-active and pixelclk-active display-timings properties yet.
Instead the data-enable and the pixel data clock polarity are hardcoded in the imx-drm driver.
So theses properties are now set to keep the same behaviour when imx-drm will start using them.
---
ChangeLog v9->v10:
- New patch that was splitted out of:
"staging imx-drm: Use de-active and pixelclk-active display-timings."
--- arch/arm/boot/dts/imx51-babbage.dts | 2 ++ arch/arm/boot/dts/imx53-m53evk.dts | 2 ++ arch/arm/boot/dts/imx53-tx53-x03x.dts | 2 +- arch/arm/boot/dts/imx6qdl-gw53xx.dtsi | 2 ++ arch/arm/boot/dts/imx6qdl-gw54xx.dtsi | 2 ++ arch/arm/boot/dts/imx6qdl-nitrogen6x.dtsi | 2 ++ arch/arm/boot/dts/imx6qdl-sabreauto.dtsi | 2 ++ arch/arm/boot/dts/imx6qdl-sabrelite.dtsi | 2 ++ arch/arm/boot/dts/imx6qdl-sabresd.dtsi | 2 ++ 9 files changed, 17 insertions(+), 1 deletion(-)
arch/arm/boot/dts/imx51-babbage.dts +2 -0
@@ -38,6 +38,8 @@ vfront-porch = <7>; hsync-len = <60>; vsync-len = <10>; + de-active = <1>; + pixelclk-active = <0>; }; };
arch/arm/boot/dts/imx53-m53evk.dts +2 -0
@@ -41,6 +41,8 @@ vfront-porch = <9>; vsync-len = <3>; vsync-active = <1>; + de-active = <1>; + pixelclk-active = <0>; }; }; };
arch/arm/boot/dts/imx53-tx53-x03x.dts +1 -1
@@ -93,7 +93,7 @@ hsync-active = <0>; vsync-active = <0>; de-active = <1>; - pixelclk-active = <1>; + pixelclk-active = <0>; }; ET0500 {
arch/arm/boot/dts/imx6qdl-gw53xx.dtsi +2 -0
@@ -494,6 +494,8 @@ vfront-porch = <7>; hsync-len = <60>; vsync-len = <10>; + de-active = <1>; + pixelclk-active = <0>; }; }; };
arch/arm/boot/dts/imx6qdl-gw54xx.dtsi +2 -0
@@ -516,6 +516,8 @@ vfront-porch = <7>; hsync-len = <60>; vsync-len = <10>; + de-active = <1>; + pixelclk-active = <0>; }; }; };
arch/arm/boot/dts/imx6qdl-nitrogen6x.dtsi +2 -0
@@ -349,6 +349,8 @@ vfront-porch = <7>; hsync-len = <60>; vsync-len = <10>; + de-active = <1>; + pixelclk-active = <0>; }; }; };
arch/arm/boot/dts/imx6qdl-sabreauto.dtsi +2 -0
@@ -405,6 +405,8 @@ vfront-porch = <7>; hsync-len = <60>; vsync-len = <10>; + de-active = <1>; + pixelclk-active = <0>; }; }; };
arch/arm/boot/dts/imx6qdl-sabrelite.dtsi +2 -0
@@ -349,6 +349,8 @@ vfront-porch = <7>; hsync-len = <60>; vsync-len = <10>; + de-active = <1>; + pixelclk-active = <0>; }; }; };
arch/arm/boot/dts/imx6qdl-sabresd.dtsi +2 -0
@@ -463,6 +463,8 @@ vfront-porch = <7>; hsync-len = <60>; vsync-len = <10>; + de-active = <1>; + pixelclk-active = <0>; }; }; };
Signature · 1 line
1.7.9.5
Re: [PATCH v12][ 06/12] ARM: dts: imx5*, imx6*: correct display-timings nodes.
Quoted 27 lines · Denis Carikli
The imx-drm driver can't use the de-active and pixelclk-active display-timings properties yet.
Instead the data-enable and the pixel data clock polarity are hardcoded in the imx-drm driver.
So theses properties are now set to keep the same behaviour when imx-drm will start using them.
Signed-off-by Denis Carikli <[email protected]>---
ChangeLogv9->v10:
- New patch that was splitted out of:
"staging imx-drm: Use de-active and pixelclk-active display-timings."--- arch/arm/boot/dts/imx51-babbage.dts | 2 ++ arch/arm/boot/dts/imx53-m53evk.dts | 2 ++ arch/arm/boot/dts/imx53-tx53-x03x.dts | 2 +- arch/arm/boot/dts/imx6qdl-gw53xx.dtsi | 2 ++ arch/arm/boot/dts/imx6qdl-gw54xx.dtsi | 2 ++ arch/arm/boot/dts/imx6qdl-nitrogen6x.dtsi | 2 ++ arch/arm/boot/dts/imx6qdl-sabreauto.dtsi | 2 ++ arch/arm/boot/dts/imx6qdl-sabrelite.dtsi | 2 ++ arch/arm/boot/dts/imx6qdl-sabresd.dtsi | 2 ++ 9 files changed, 17 insertions(+), 1 deletion(-)
...
arch/arm/boot/dts/imx53-tx53-x03x.dts line 96
Quoted 10 lines
arch/arm/boot/dts/imx53-tx53-x03x.dts +1
-1@@ -93,7 +93,7 @@ hsync-active = <0>; vsync-active = <0>; de-active = <1>; - pixelclk-active = <1>; + pixelclk-active = <0>;
@Lothar, is this change correct?
Shawn
Quoted 3 lines
arch/arm/boot/dts/imx53-tx53-x03x.dts +0
-0}; ET0500 {
Re: [PATCH v12][ 06/12] ARM: dts: imx5*, imx6*: correct display-timings nodes.
Hi,
Quoted 31 lines · Shawn Guo
Quoted 27 lines · Denis Carikli
The imx-drm driver can't use the de-active and pixelclk-active display-timings properties yet.
Instead the data-enable and the pixel data clock polarity are hardcoded in the imx-drm driver.
So theses properties are now set to keep the same behaviour when imx-drm will start using them.
Signed-off-by Denis Carikli <[email protected]>---
ChangeLogv9->v10:
- New patch that was splitted out of:
"staging imx-drm: Use de-active and pixelclk-active display-timings."--- arch/arm/boot/dts/imx51-babbage.dts | 2 ++ arch/arm/boot/dts/imx53-m53evk.dts | 2 ++ arch/arm/boot/dts/imx53-tx53-x03x.dts | 2 +- arch/arm/boot/dts/imx6qdl-gw53xx.dtsi | 2 ++ arch/arm/boot/dts/imx6qdl-gw54xx.dtsi | 2 ++ arch/arm/boot/dts/imx6qdl-nitrogen6x.dtsi | 2 ++ arch/arm/boot/dts/imx6qdl-sabreauto.dtsi | 2 ++ arch/arm/boot/dts/imx6qdl-sabrelite.dtsi | 2 ++ arch/arm/boot/dts/imx6qdl-sabresd.dtsi | 2 ++ 9 files changed, 17 insertions(+), 1 deletion(-)...
Quoted 13 lines
arch/arm/boot/dts/imx53-tx53-x03x.dts line 96
Quoted 10 lines
arch/arm/boot/dts/imx53-tx53-x03x.dts +1
-1@@ -93,7 +93,7 @@ hsync-active = <0>; vsync-active = <0>; de-active = <1>; - pixelclk-active = <1>; + pixelclk-active = <0>;@Lothar, is this change correct?
No, the ET0430 display which is affected by this patch actually has an inverted clock wrt the other displays of the family.
'pixelclk-active = <1>' is the correct setting for this display!
Thanks, Shawn for the reminder.
Lothar Waßmann
Signature · 13 lines
___________________________________________________________ Ka-Ro electronics GmbH | Pascalstraße 22 | D - 52076 Aachen Phone: +49 2408 1402-0 | Fax: +49 2408 1402-10 Geschäftsführer: Matthias Kaussen Handelsregistereintrag: Amtsgericht Aachen, HRB 4996 www.karo-electronics.de | [email protected] ___________________________________________________________ _______________________________________________ devel mailing list [email protected] http://driverdev.linuxdriverproject.org/mailman/listinfo/driverdev-devel
PATCH v12 7/12 drm: drm_display_mode: add signal polarity flags
In reply to Denis CarikliWe need a way to pass signal polarity informations
between DRM panels, and the display drivers.
To do that, a pol_flags field was added to drm_display_mode.
---
ChangeLog v11->v12:
- Rebased: This patch now applies against drm_modes.h
- Rebased: It now uses the new DRM_MODE_FLAG_POL_DE flags defines names
ChangeLog v10->v11:
- Since the imx-drm won't be able to retrive its regulators from the device tree when using display-timings nodes, and that I was told that the drm simple-panel driver already supported that, I then, instead, added what was lacking to make the eukrea displays work with the drm-simple-panel driver.
That required a way to get back the display polarity informations from the imx-drm driver without affecting userspace.
--- include/drm/drm_modes.h | 8 ++++++++ 1 file changed, 8 insertions(+)
include/drm/drm_modes.h +8 -0
@@ -93,6 +93,13 @@ enum drm_mode_status {#define DRM_MODE_FLAG_3D_MAX DRM_MODE_FLAG_3D_SIDE_BY_SIDE_HALF +#define DRM_MODE_FLAG_POL_PIXDATA_NEGEDGE BIT(1) +#define DRM_MODE_FLAG_POL_PIXDATA_POSEDGE BIT(2) +#define DRM_MODE_FLAG_POL_PIXDATA_PRESERVE BIT(3) +#define DRM_MODE_FLAG_POL_DE_LOW BIT(4) +#define DRM_MODE_FLAG_POL_DE_HIGH BIT(5) +#define DRM_MODE_FLAG_POL_DE_PRESERVE BIT(6) +struct drm_display_mode {/* Header */ struct list_head head;
@@ -144,6 +151,7 @@ struct drm_display_mode {int vrefresh;/* in Hz */ int hsync;/* in kHz */ enum hdmi_picture_aspect picture_aspect_ratio; +unsigned int pol_flags; };/* mode specified on the command line */
Signature · 1 line
1.7.9.5
Re: [PATCH v12][ 07/12] drm: drm_display_mode: add signal polarity flags
Hi Denis,
Quoted 31 lines · Denis Carikli
We need a way to pass signal polarity informations
between DRM panels, and the display drivers.To do that, a
pol_flagsfield was added todrm_display_mode.Signed-off-by Denis Carikli <[email protected]>---
ChangeLogv11->v12:
- Rebased: This patch now applies againstdrm_modes.h
- Rebased: It now uses the newDRM_MODE_FLAG_POL_DEflags defines namesChangeLog
v10->v11:
- Since the imx-drm won't be able to retrive its regulators from the device tree when using display-timings nodes, and that I was told that the drm simple-panel driver already supported that, I then, instead, added what was lacking to make the eukrea displays work with the drm-simple-panel driver.That required a way to get back the display polarity informations from the imx-drm driver without affecting userspace.
--- include/drm/drm_modes.h | 8 ++++++++ 1 file changed, 8 insertions(+)include/drm/drm_modes.h +0
-0
include/drm/drm_modes.h enum drm_mode_status { · line 98
Quoted 6 lines
include/drm/drm_modes.h +3
-0@@ -93,6 +93,13 @@ enum drm_mode_status {#define DRM_MODE_FLAG_3D_MAX DRM_MODE_FLAG_3D_SIDE_BY_SIDE_HALF +#define DRM_MODE_FLAG_POL_PIXDATA_NEGEDGE BIT(1) +#define DRM_MODE_FLAG_POL_PIXDATA_POSEDGE BIT(2) +#define DRM_MODE_FLAG_POL_PIXDATA_PRESERVE BIT(3)
What is the purpose of DRM_MODE_FLAG_POL_PIXDATA_PRESERVE?
If 'preserve' means 'ignore' we can set to zero negedge and posedge bits instead of adding new bit. If it is something different please describe it.
include/drm/drm_modes.h enum drm_mode_status { · line 102
Quoted 4 lines
include/drm/drm_modes.h +4
-0+#define DRM_MODE_FLAG_POL_DE_LOW BIT(4) +#define DRM_MODE_FLAG_POL_DE_HIGH BIT(5) +#define DRM_MODE_FLAG_POL_DE_PRESERVE BIT(6) +
The same comments here.
include/drm/drm_modes.h struct drm_display_mode { · line 154
Quoted 8 lines
include/drm/drm_modes.h +1
-0struct drm_display_mode {/* Header */ struct list_head head;@@ -144,6 +151,7 @@ struct drm_display_mode {int vrefresh;/* in Hz */ int hsync;/* in kHz */ enum hdmi_picture_aspect picture_aspect_ratio; +unsigned int pol_flags;
Adding field and macros description to the DocBook would be nice.
Regards
Andrzej
Quoted 4 lines
include/drm/drm_modes.h +0
-0};/* mode specified on the command line */
Re: [PATCH v12][ 07/12] drm: drm_display_mode: add signal polarity flags
Quoted 2 lines · Andrzej Hajda
Hi Denis,
Hi,
Quoted 7 lines
include/drm/drm_modes.h enum drm_mode_status { · line 98
Quoted 3 lines
include/drm/drm_modes.h +3
-0+#define DRM_MODE_FLAG_POL_PIXDATA_NEGEDGE BIT(1) +#define DRM_MODE_FLAG_POL_PIXDATA_POSEDGE BIT(2) +#define DRM_MODE_FLAG_POL_PIXDATA_PRESERVE BIT(3)What is the purpose of
DRM_MODE_FLAG_POL_PIXDATA_PRESERVE?
If 'preserve' means 'ignore' we can set to zero negedge and posedge bits instead of adding new bit. If it is something different please describe it.
Yes, it meant 'ignore'.
The goal was to be able to have a way to keep the old behavior while still being able to set the flags.
So, with the imx-drm driver, if none of the DRM_MODE_FLAG_POL_PIXDATA were set(that is POSEDGE, NEGEDGE, PRESERVE), then in ipuv3-crtc.c, it went using the old flags settings that were previously hardcoded.
The same applied for DRM_MODE_FLAG_POL_DE.
The patch using theses flags is the 08/12 of this same serie.
Quoted 1 line
Quoted 1 line
struct drm_display_mode {
[..]
Quoted 3 lines
include/drm/drm_modes.h struct drm_display_mode { · line 154
Quoted 1 line
include/drm/drm_modes.h +1
-0+unsigned int pol_flags;Adding field and macros description to the DocBook would be nice.
So I will have to describe it in the "Connector Helper Operations" section of drm.tmpl, right before the mode_valid synopsis ?
Denis.
Re: [PATCH v12][ 07/12] drm: drm_display_mode: add signal polarity flags
Quoted 17 lines · Denis Carikli
Quoted 2 lines · Andrzej Hajda
Hi Denis,
Hi,
Quoted 7 lines
include/drm/drm_modes.h enum drm_mode_status { · line 98
Quoted 3 lines
include/drm/drm_modes.h +3
-0+#define DRM_MODE_FLAG_POL_PIXDATA_NEGEDGE BIT(1) +#define DRM_MODE_FLAG_POL_PIXDATA_POSEDGE BIT(2) +#define DRM_MODE_FLAG_POL_PIXDATA_PRESERVE BIT(3)What is the purpose of
DRM_MODE_FLAG_POL_PIXDATA_PRESERVE?
If 'preserve' means 'ignore' we can set to zero negedge and posedge bits instead of adding new bit. If it is something different please describe it.Yes, it meant 'ignore'.
The goal was to be able to have a way to keep the old behavior while still being able to set the flags.
Quoted 6 lines
So, with the imx-drm driver, if none of the
DRM_MODE_FLAG_POL_PIXDATAwereset(that is POSEDGE, NEGEDGE, PRESERVE), then inipuv3-crtc.c, it went using the old flags settings that were previously hardcoded.The same applied for
DRM_MODE_FLAG_POL_DE.
The patch using theses flags is the 08/12 of this same serie.
So as I understand you want to:
- do not change hw polarity settings by using preserve bit,
- keep the old behavior of the driver by setting all bits to zero.
I think this is the issue of the specific driver, and it should not influence core structs.
I am not familiar with imx but I guess it should not be a problem to solve the issue in the driver.
Quoted 8 lines
Quoted 2 lines
Quoted 2 lines
struct drm_display_mode {[..]
Quoted 3 lines
include/drm/drm_modes.h struct drm_display_mode { · line 154
Quoted 1 line
include/drm/drm_modes.h +1
-0+unsigned int pol_flags;Adding field and macros description to the DocBook would be nice.
So I will have to describe it in the "Connector Helper Operations" section of drm.tmpl, right before the
mode_validsynopsis ?
Yes, I think so.
Andrzej
Quoted 3 lines
Denis.
PATCH v12 8/12 imx-drm: Use drm_display_mode timings flags.
In reply to Denis CarikliThe previous hardware behaviour was kept if the
flags are not set.
---
ChangeLog v11->v12:
- Rebased: It now uses the following new flags defines names:
CLK_POL, ENABLE_POL
- The inversions in ipuv3-crtc.c are now fixed.
- ipuv3-crtc.c was still using mode->private_flags from the previous versions of this patchset, that's now fixed.
ChangeLog v10->v11:
- This patch was splitted-out and adapted from:
"Prepare imx-drm for extra display-timings retrival."
- The display-timings dt specific part was removed.
- The flags names were changed to use the DRM ones from:
"drm: drm_display_mode: add signal polarity flags"
--- drivers/staging/imx-drm/ipu-v3/imx-ipu-v3.h | 6 ++++-- drivers/staging/imx-drm/ipu-v3/ipu-di.c | 7 ++++++- drivers/staging/imx-drm/ipuv3-crtc.c | 20 ++++++++++++++++++-- 3 files changed, 28 insertions(+), 5 deletions(-)
drivers/staging/imx-drm/ipu-v3/imx-ipu-v3.h +4 -2
@@ -29,9 +29,11 @@ enum ipuv3_type {#define CLK_POL_NEGEDGE 0#define CLK_POL_POSEDGE 1 +#define CLK_POL_PRESERVE 2#define ENABLE_POL_LOW 0#define ENABLE_POL_HIGH 1 +#define ENABLE_POL_PRESERVE 2/* * Bitfield of Display Interface signal polarities.
@@ -43,10 +45,10 @@ struct ipu_di_signal_cfg { unsigned clksel_en:1; unsigned clkidle_en:1; unsigned data_pol:1; /* true = inverted */ - unsigned clk_pol:1; - unsigned enable_pol:1; unsigned Hsync_pol:1; /* true = active high */ unsigned Vsync_pol:1; +u8 clk_pol; +u8 enable_pol;u16 width;u16 height;
drivers/staging/imx-drm/ipu-v3/ipu-di.c +6 -1
@@ -597,6 +597,8 @@ int ipu_di_init_sync_panel(struct ipu_di *di, struct ipu_di_signal_cfg *sig)if (sig->clk_pol ==CLK_POL_POSEDGE ) di_gen |=DI_GEN_POLARITY_DISP_CLK ; +else if (sig->clk_pol ==CLK_POL_NEGEDGE ) + di_gen &= ~DI_GEN_POLARITY_DISP_CLK ;ipu_di_write (di, di_gen,DI_GENERAL );
@@ -604,10 +606,13 @@ int ipu_di_init_sync_panel(struct ipu_di *di, struct ipu_di_signal_cfg *sig) DI_SYNC_AS_GEN); reg =ipu_di_read (di,DI_POL ); - reg &= ~(DI_POL_DRDY_DATA_POLARITY |DI_POL_DRDY_POLARITY_15 ); + reg &= ~(DI_POL_DRDY_DATA_POLARITY );if (sig->enable_pol ==ENABLE_POL_HIGH ) reg |=DI_POL_DRDY_POLARITY_15 ; +else if (sig->enable_pol ==ENABLE_POL_LOW ) + reg &= ~DI_POL_DRDY_POLARITY_15 ; +if (sig->data_pol) reg |=DI_POL_DRDY_DATA_POLARITY ;
drivers/staging/imx-drm/ipuv3-crtc.c +18 -2
@@ -157,8 +157,24 @@ static int ipu_crtc_mode_set(struct drm_crtc *crtc,if (mode->flags &DRM_MODE_FLAG_PVSYNC ) sig_cfg.Vsync_pol =1 ; - sig_cfg.enable_pol =ENABLE_POL_HIGH ; - sig_cfg.clk_pol =CLK_POL_NEGEDGE ; +if (mode->pol_flags &DRM_MODE_FLAG_POL_PIXDATA_POSEDGE ) + sig_cfg.clk_pol =CLK_POL_POSEDGE ; +else if (mode->pol_flags &DRM_MODE_FLAG_POL_PIXDATA_NEGEDGE ) + sig_cfg.clk_pol =CLK_POL_NEGEDGE ; +else if (mode->pol_flags &DRM_MODE_FLAG_POL_PIXDATA_PRESERVE ) + sig_cfg.clk_pol =CLK_POL_PRESERVE ; +else + sig_cfg.clk_pol =CLK_POL_NEGEDGE ; + +if (mode->pol_flags &DRM_MODE_FLAG_POL_DE_HIGH ) + sig_cfg.enable_pol =ENABLE_POL_HIGH ; +else if (mode->pol_flags &DRM_MODE_FLAG_POL_DE_LOW ) + sig_cfg.enable_pol =ENABLE_POL_LOW ; +else if (mode->pol_flags &DRM_MODE_FLAG_POL_DE_PRESERVE ) + sig_cfg.enable_pol =ENABLE_POL_PRESERVE ; +else + sig_cfg.enable_pol =ENABLE_POL_HIGH ; + sig_cfg.width = mode->hdisplay; sig_cfg.height = mode->vdisplay; sig_cfg.pixel_fmt = out_pixel_fmt;
Signature · 1 line
1.7.9.5
PATCH v12 9/12 drm/panel: Add Eukrea mbimxsd51 displays.
In reply to Denis Carikli---
ChangeLog v11->v12:
- Rebased: It now uses the new DRM_MODE_FLAG_POL_DE flags defines names
ChangeLog v10->v11:
- New patch.
--- .../bindings/panel/eukrea,mbimxsd51-cmo-qvga.txt | 7 ++ .../bindings/panel/eukrea,mbimxsd51-dvi-svga.txt | 7 ++ .../bindings/panel/eukrea,mbimxsd51-dvi-vga.txt | 7 ++ drivers/gpu/drm/panel/panel-simple.c | 81 ++++++++++++++++++++ 4 files changed, 102 insertions(+) create mode 100644 Documentation/devicetree/bindings/panel/eukrea,mbimxsd51-cmo-qvga.txt create mode 100644 Documentation/devicetree/bindings/panel/eukrea,mbimxsd51-dvi-svga.txt create mode 100644 Documentation/devicetree/bindings/panel/eukrea,mbimxsd51-dvi-vga.txt
Documentation/devicetree/bindings/panel/eukrea,mbimxsd51-cmo-qvga.txt new file +7 -0
@@ -0,0 +1,7 @@ +Eukrea CMO-QVGA (320x240 pixels) TFT LCD panel + +Required properties: +- compatible: should be "eukrea,mbimxsd51-cmo-qvga" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory.
Documentation/devicetree/bindings/panel/eukrea,mbimxsd51-dvi-svga.txt new file +7 -0
@@ -0,0 +1,7 @@ +Eukrea DVI-SVGA (800x600 pixels) DVI output. + +Required properties: +- compatible: should be "eukrea,mbimxsd51-dvi-svga" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory.
Documentation/devicetree/bindings/panel/eukrea,mbimxsd51-dvi-vga.txt new file +7 -0
@@ -0,0 +1,7 @@ +Eukrea DVI-VGA (640x480 pixels) DVI output. + +Required properties: +- compatible: should be "eukrea,mbimxsd51-dvi-vga" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory.
drivers/gpu/drm/panel/panel-simple.c +81 -0
93 lines not on this page · raw message
Signature · 1 line
1.7.9.5
Re: [PATCH v12][ 09/12] drm/panel: Add Eukrea mbimxsd51 displays.
On Mon, Apr 07, 2014 at 02:44:48PM +0200, Denis Carikli wrote:
[...]
Quoted 8 lines
drivers/gpu/drm/panel/panel-simple.c +8
-0+static const struct panel_desc eukrea_mbimxsd51_dvisvga = { + .modes = &eukrea_mbimxsd51_dvisvga_mode, + .num_modes =1 , + .size = { + .width =0 , + .height =0 , + }, +};
[...]
drivers/gpu/drm/panel/panel-simple.c static const struct panel_desc chunghwa_claa101wb01 = { · line 401
Quoted 8 lines
drivers/gpu/drm/panel/panel-simple.c +8
-0+static const struct panel_desc eukrea_mbimxsd51_dvivga = { + .modes = &eukrea_mbimxsd51_dvivga_mode, + .num_modes =1 , + .size = { + .width =0 , + .height =0 , + }, +};
Surely these two panels have a physical size?
Thierry
-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 836 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20140409/1168cba1/attachment-0001.sig>
PATCH v12 10/12 ARM: dts: mbimx51sd: Add display support.
In reply to Denis CarikliThe CMO-QVGA, DVI-SVGA and DVI-VGA are added.
---
ChangeLog v10->v11:
- Now uses the drm-panel instead of the display-timings. This is to get regulator support, which is lacking in the imx-drm driver when using the display-timings.
ChangeLog v9->v10:
- Rebased
- Now enables the cmo-qvga regulator at boot.
ChangeLog v8->v9:
- Removed the Cc. They are now set in git-send-email directly.
- updated pixelclk-active after the following patch:
"imx-drm: Match ipu_di_signal_cfg's clk_pol with its description."
ChangeLog v7->v8:
- Rebased the patch: added the now required imx-drm node.
- Adapted the svga clock-frequency value in order to still be able to display an image after the following commit:
"imx-drm: ipu-v3: more inteligent DI clock selection"
ChangeLog v6->v7:
- Shrinked even more the Cc list.
- Since the pingrp headers were removed, the references to it where replaced by the actual pins.
- Added the targets to arch/arm/boot/dts/Makefile
ChangeLog v5->v6:
- Reordered the Cc list.
ChangeLog v3->v5:
- Updated to new GPIO defines.
- Updated to new licenses checkpatch requirements.
- one whitespace cleanup.
ChangeLog v2->v3:
- Splitted out from the patch that added support for the cpuimx51/mbimxsd51 boards.
- This patch now only adds display support.
- Added some interested people in the Cc list, and removed some people that might be annoyed by the receiving of that patch which is unrelated to their subsystem.
- rebased and reworked the dts displays addition.
- Also rebased and reworked the fsl,pins usage.
--- arch/arm/boot/dts/Makefile | 3 ++ .../imx51-eukrea-mbimxsd51-baseboard-cmo-qvga.dts | 41 ++++++++++++++++ .../imx51-eukrea-mbimxsd51-baseboard-dvi-svga.dts | 28 +++++++++++ .../imx51-eukrea-mbimxsd51-baseboard-dvi-vga.dts | 28 +++++++++++ .../boot/dts/imx51-eukrea-mbimxsd51-baseboard.dts | 49 ++++++++++++++++++++ 5 files changed, 149 insertions(+) create mode 100644 arch/arm/boot/dts/imx51-eukrea-mbimxsd51-baseboard-cmo-qvga.dts create mode 100644 arch/arm/boot/dts/imx51-eukrea-mbimxsd51-baseboard-dvi-svga.dts create mode 100644 arch/arm/boot/dts/imx51-eukrea-mbimxsd51-baseboard-dvi-vga.dts
arch/arm/boot/dts/Makefile +3 -0
@@ -166,6 +166,9 @@ dtb-$(CONFIG_ARCH_MXC) += \ imx51-apf51dev.dtb \ imx51-babbage.dtb \ imx51-eukrea-mbimxsd51-baseboard.dtb \ + imx51-eukrea-mbimxsd51-baseboard-cmo-qvga.dtb \ + imx51-eukrea-mbimxsd51-baseboard-dvi-svga.dtb \ + imx51-eukrea-mbimxsd51-baseboard-dvi-vga.dtb \ imx53-ard.dtb \ imx53-m53evk.dtb \ imx53-mba53.dtb \
arch/arm/boot/dts/imx51-eukrea-mbimxsd51-baseboard-cmo-qvga.dts new file +41 -0
41 lines not on this page · raw message
arch/arm/boot/dts/imx51-eukrea-mbimxsd51-baseboard-dvi-svga.dts new file +28 -0
@@ -0,0 +1,28 @@ +/* + * Copyright 2013 Eukréa Electromatique <[email protected]> + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * as published by the Free Software Foundation; either version 2 + * of the License, or (at your option) any later version. + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +#include "imx51-eukrea-mbimxsd51-baseboard.dts" + +/ { + model = "Eukrea MBIMXSD51 with the DVI-SVGA Display"; + compatible = "eukrea,mbimxsd51-baseboard-dvi-svga", "eukrea,mbimxsd51-baseboard", "eukrea,cpuimx51", "fsl,imx51"; + + panel: panel { + compatible = "eukrea,mbimxsd51-dvi-svga", "simple-panel"; + }; +}; + +&display { + status = "okay"; + fsl,panel = <&panel>; +};
arch/arm/boot/dts/imx51-eukrea-mbimxsd51-baseboard-dvi-vga.dts new file +28 -0
@@ -0,0 +1,28 @@ +/* + * Copyright 2013 Eukréa Electromatique <[email protected]> + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * as published by the Free Software Foundation; either version 2 + * of the License, or (at your option) any later version. + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +#include "imx51-eukrea-mbimxsd51-baseboard.dts" + +/ { + model = "Eukrea MBIMXSD51 with the DVI-VGA Display"; + compatible = "eukrea,mbimxsd51-baseboard-dvi-vga", "eukrea,mbimxsd51-baseboard", "eukrea,cpuimx51", "fsl,imx51"; + + panel: panel { + compatible = "eukrea,mbimxsd51-dvi-vga", "simple-panel"; + }; +}; + +&display { + status = "okay"; + fsl,panel = <&panel>; +};
arch/arm/boot/dts/imx51-eukrea-mbimxsd51-baseboard.dts +49 -0
67 lines not on this page · raw message
Signature · 1 line
1.7.9.5
PATCH v12 11/12 ARM: dts: mbimx51sd: Add CMO-QVGA backlight support.
In reply to Denis Carikli---
ChangeLog v9->v11:
- Now uses the drm-panel instead of the display-timings.
ChangeLog v8->v9:
- Removed the Cc. They are now set in git-send-email directly.
- The backlight is now on at boot.
ChangeLog v6->v7:
- Shrinked even more the Cc list.
ChangeLog v5->v6:
- Reordered the Cc list.
ChangeLog v3->v5:
- Updated to the new GPIO defines.
ChangeLog v2->v3:
- Splitted out from the patch that added support for the cpuimx51/mbimxsd51 boards.
- This patch now only adds backlight support.
- Added some interested people in the Cc list, and removed some people that might be annoyed by the receiving of that patch which is unrelated to their subsystem.
--- .../imx51-eukrea-mbimxsd51-baseboard-cmo-qvga.dts | 10 ++++++++++ 1 file changed, 10 insertions(+)
arch/arm/boot/dts/imx51-eukrea-mbimxsd51-baseboard-cmo-qvga.dts +10 -0
@@ -17,9 +17,19 @@ model = "Eukrea MBIMXSD51 with the CMO-QVGA Display"; compatible = "eukrea,mbimxsd51-baseboard-cmo-qvga", "eukrea,mbimxsd51-baseboard", "eukrea,cpuimx51", "fsl,imx51"; + backlight: backlight { + compatible = "gpio-backlight"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_backlight_1>; + gpios = <&gpio3 4 GPIO_ACTIVE_HIGH>; + default-brightness-level = <1>; + default-on; + }; + panel: panel { compatible = "eukrea,mbimxsd51-cmo-qvga", "simple-panel"; power-supply = <®_lcd_3v3>; + backlight = <&backlight>; }; reg_lcd_3v3: lcd-en {
Signature · 1 line
1.7.9.5
PATCH v12 12/12 ARM: imx_v6_v7_defconfig: Add more drm drivers.
In reply to Denis CarikliThe DRM_PANEL_SIMPLE is needed by the eukrea
mbimxsd51's displays.
---
ChangeLog v10->v11:
- New patch, splitting it would be overkill.
--- arch/arm/configs/imx_v6_v7_defconfig | 2 ++ 1 file changed, 2 insertions(+)
arch/arm/configs/imx_v6_v7_defconfig +2 -0
@@ -183,6 +183,7 @@ CONFIG_V4L_MEM2MEM_DRIVERS=y CONFIG_VIDEO_CODA=y CONFIG_SOC_CAMERA_OV2640=y CONFIG_DRM=y +CONFIG_DRM_PANEL_SIMPLE=y CONFIG_BACKLIGHT_LCD_SUPPORT=y CONFIG_LCD_CLASS_DEVICE=y CONFIG_LCD_L4F00242T03=y
@@ -245,6 +246,7 @@ CONFIG_DRM_IMX_TVE=y CONFIG_DRM_IMX_LDB=y CONFIG_DRM_IMX_IPUV3_CORE=y CONFIG_DRM_IMX_IPUV3=y +CONFIG_DRM_IMX_HDMI=y CONFIG_COMMON_CLK_DEBUG=y # CONFIG_IOMMU_SUPPORT is not set CONFIG_PWM=y
Signature · 1 line
1.7.9.5
Shawn Guo
AppliedRe: [PATCH v12][ 12/12] ARM: imx_v6_v7_defconfig: Add more drm drivers.
Quoted 4 lines · Denis Carikli
The
DRM_PANEL_SIMPLEis needed by the eukrea
mbimxsd51's displays.Signed-off-by Denis Carikli <[email protected]>
Applied, thanks.