Skip to contentSkip to conversation

ARM: sun6i: Enable USB Host support on the Colombus board

PATCH New Maxime Ripard 2 participants 5 messages May 20, 2014 – May 22, 2014

Subsystems (2)
Device tree bindings Arm/Allwinner sunXi SoC support
lore
Share & tools
lore

Maxime Ripard

author
#0 lore raw

PATCH 1/1 ARM: sun6i: Enable USB Host support on the Colombus board

The colombus board has a on-board USB hub, that is enabled through the pin PH24, and wired to the first EHCI controller.

Signed-off-by Maxime Ripard <[email protected]>
---
 arch/arm/boot/dts/sun6i-a31-colombus.dts | 26 ++++++++++++++++++++++++++
 1 file changed, 26 insertions(+)
arch/arm/boot/dts/sun6i-a31-colombus.dts +26 -0
index 3898a7bce831..a907c1d3e939 100644
@@ -13,6 +13,7 @@
 
 /dts-v1/;
 /include/ "sun6i-a31.dtsi"
+/include/ "sunxi-common-regulators.dtsi"
 
 / {
 	model = "WITS A31 Colombus Evaluation Board";

@@ -23,6 +24,24 @@
 	};
 
 	soc at 01c00000 {
+		pio: pinctrl at 01c20800 {
+			usb2_vbus_pin_colombus: usb2_vbus_pin at 0 {
+				allwinner,pins = "PH24";
+				allwinner,function = "gpio_out";
+				allwinner,drive = <0>;
+				allwinner,pull = <0>;
+			};
+		};
+
+		usbphy: phy at 01c19400 {
+			usb2_vbus-supply = <&reg_usb2_vbus>;
+			status = "okay";
+		};
+
+		ehci1: usb at 01c1b000 {
+			status = "okay";
+		};
+
 		uart0: serial at 01c28000 {
 			pinctrl-names = "default";
 			pinctrl-0 = <&uart0_pins_a>;

@@ -47,4 +66,11 @@
 			status = "okay";
 		};
 	};
+
+	reg_usb2_vbus: usb2-vbus {
+		pinctrl-names = "default";
+		pinctrl-0 = <&usb2_vbus_pin_colombus>;
+		gpio = <&pio 7 24 0>;
+		status = "okay";
+	};
 };
Signature · 1 line
1.9.3
#1 lore raw

PATCH 1/1 ARM: sun6i: Enable USB Host support on the Colombus board

Hi,

Quoted 2 lines · Maxime Ripard

The colombus board has a on-board USB hub, that is enabled through the pin PH24, and wired to the first EHCI controller.

ehci0 is not hooked up at all on this board ? I would expect it to go to a usb wifi card for example.

Assuming that ehci0 is not hooked up, this is:

Reviewed-by Hans de Goede <[email protected]>

If it is hooked up I believe both usb controllers should be enabled.

Regards,

Hans

Quoted 56 lines
Signed-off-by Maxime Ripard <[email protected]>
---
 arch/arm/boot/dts/sun6i-a31-colombus.dts | 26 ++++++++++++++++++++++++++
 1 file changed, 26 insertions(+)
arch/arm/boot/dts/sun6i-a31-colombus.dts +26 -0
index 3898a7bce831..a907c1d3e939 100644
@@ -13,6 +13,7 @@
 
 /dts-v1/;
 /include/ "sun6i-a31.dtsi"
+/include/ "sunxi-common-regulators.dtsi"
 
 / {
 	model = "WITS A31 Colombus Evaluation Board";

@@ -23,6 +24,24 @@
 	};
 
 	soc at 01c00000 {
+		pio: pinctrl at 01c20800 {
+			usb2_vbus_pin_colombus: usb2_vbus_pin at 0 {
+				allwinner,pins = "PH24";
+				allwinner,function = "gpio_out";
+				allwinner,drive = <0>;
+				allwinner,pull = <0>;
+			};
+		};
+
+		usbphy: phy at 01c19400 {
+			usb2_vbus-supply = <&reg_usb2_vbus>;
+			status = "okay";
+		};
+
+		ehci1: usb at 01c1b000 {
+			status = "okay";
+		};
+
 		uart0: serial at 01c28000 {
 			pinctrl-names = "default";
 			pinctrl-0 = <&uart0_pins_a>;

@@ -47,4 +66,11 @@
 			status = "okay";
 		};
 	};
+
+	reg_usb2_vbus: usb2-vbus {
+		pinctrl-names = "default";
+		pinctrl-0 = <&usb2_vbus_pin_colombus>;
+		gpio = <&pio 7 24 0>;
+		status = "okay";
+	};
 };
author
#2 lore raw

PATCH 1/1 ARM: sun6i: Enable USB Host support on the Colombus board

Hi,

Quoted 6 lines · Hans de Goede

Hi,

Quoted 2 lines · Maxime Ripard

The colombus board has a on-board USB hub, that is enabled through the pin PH24, and wired to the first EHCI controller.

Quoted 6 lines

ehci0 is not hooked up at all on this board ? I would expect it to go to a usb wifi card for example.

Assuming that ehci0 is not hooked up, this is:

Reviewed-by Hans de Goede <[email protected]>

It's unclear, because the schematics say that we have two options, either USB or SDIO wifi chips.

However, looking at the boards, it looks like it's the latter.

Maxime

Signature · 10 lines
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20140520/8c74ab48/attachment.sig>
#3 lore raw

PATCH 1/1 ARM: sun6i: Enable USB Host support on the Colombus board

Hi,

Quoted 12 lines · Maxime Ripard

Hi,

Quoted 9 lines · Hans de Goede

Hi,

Quoted 2 lines · Maxime Ripard

The colombus board has a on-board USB hub, that is enabled through the pin PH24, and wired to the first EHCI controller.

ehci0 is not hooked up at all on this board ? I would expect it to go to a usb wifi card for example.

Quoted 8 lines
Quoted 3 lines

Assuming that ehci0 is not hooked up, this is:

Reviewed-by Hans de Goede <[email protected]>

It's unclear, because the schematics say that we have two options, either USB or SDIO wifi chips.

However, looking at the boards, it looks like it's the latter.

Ok.

Regards,

Hans

author Applied
#4 lore raw

PATCH 1/1 ARM: sun6i: Enable USB Host support on the Colombus board

In reply to Maxime Ripard
Quoted 4 lines · Maxime Ripard

The colombus board has a on-board USB hub, that is enabled through the pin PH24, and wired to the first EHCI controller.

Signed-off-by Maxime Ripard <[email protected]>

Applied.

Maxime

Signature · 10 lines
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20140522/d4989874/attachment.sig>