mtd: nand: omap: clean up of omap_elm and omap_gpmc driver

index 47b1f1b..4c65f3b 100644
@@ -16,7 +16,6 @@
 #include <common.h>
 #include <asm/io.h>
 #include <asm/errno.h>
-#include <linux/mtd/omap_gpmc.h>
 #include <linux/mtd/omap_elm.h>
 #include <asm/arch/hardware.h>
 

index 4c65f3b..afa629a 100644
@@ -24,14 +24,12 @@
 struct elm *elm_cfg;
 
 /**
- * elm_load_syndromes - Load BCH syndromes based on nibble selection
+ * elm_load_syndromes - Load BCH syndromes based on bch_type selection
  * @syndrome: BCH syndrome
- * @nibbles:
+ * @bch_type: BCH4/BCH8/BCH16
  * @poly: Syndrome Polynomial set to use
- *
- * Load BCH syndromes based on nibble selection
  */
-static void elm_load_syndromes(u8 *syndrome, u32 nibbles, u8 poly)
+static void elm_load_syndromes(u8 *syndrome, enum bch_level bch_type, u8 poly)
 {
 	u32 *ptr;
 	u32 val;

@@ -47,8 +45,7 @@ static void elm_load_syndromes(u8 *syndrome, u32 nibbles, u8 poly)
 				(syndrome[7] << 24);
 	writel(val, ptr);
 
-	/* BCH 8-bit with 26 nibbles (4*8=32) */
-	if (nibbles > 13) {
+	if (bch_type == BCH_8_BIT || bch_type == BCH_16_BIT) {
 		/* reg 2 */
 		ptr = &elm_cfg->syndrome_fragments[poly].syndrome_fragment_x[2];
 		val = syndrome[8] | (syndrome[9] << 8) | (syndrome[10] << 16) |

@@ -61,8 +58,7 @@ static void elm_load_syndromes(u8 *syndrome, u32 nibbles, u8 poly)
 		writel(val, ptr);
 	}
 
-	/* BCH 16-bit with 52 nibbles (7*8=56) */
-	if (nibbles > 26) {
+	if (bch_type == BCH_16_BIT) {
 		/* reg 4 */
 		ptr = &elm_cfg->syndrome_fragments[poly].syndrome_fragment_x[4];
 		val = syndrome[16] | (syndrome[17] << 8) |

@@ -86,7 +82,7 @@ static void elm_load_syndromes(u8 *syndrome, u32 nibbles, u8 poly)
 /**
  * elm_check_errors - Check for BCH errors and return error locations
  * @syndrome: BCH syndrome
- * @nibbles:
+ * @bch_type: BCH4/BCH8/BCH16
  * @error_count: Returns number of errrors in the syndrome
  * @error_locations: Returns error locations (in decimal) in this array
  *

@@ -94,14 +90,14 @@ static void elm_load_syndromes(u8 *syndrome, u32 nibbles, u8 poly)
  * and locations in the array passed. Returns -1 if error is not correctable,
  * else returns 0
  */
-int elm_check_error(u8 *syndrome, u32 nibbles, u32 *error_count,
+int elm_check_error(u8 *syndrome, enum bch_level bch_type, u32 *error_count,
 		u32 *error_locations)
 {
 	u8 poly = ELM_DEFAULT_POLY;
 	s8 i;
 	u32 location_status;
 
-	elm_load_syndromes(syndrome, nibbles, poly);
+	elm_load_syndromes(syndrome, bch_type, poly);
 
 	/* start processing */
 	writel((readl(&elm_cfg->syndrome_fragments[poly].syndrome_fragment_x[6])

index 881a636..af38f00 100644
@@ -153,7 +153,6 @@ static int __maybe_unused omap_correct_data(struct mtd_info *mtd, uint8_t *dat,
 struct nand_bch_priv {
 	uint8_t mode;
 	uint8_t type;
-	uint8_t nibbles;
 	struct bch_control *control;
 	enum omap_ecc ecc_scheme;
 };

@@ -163,11 +162,6 @@ struct nand_bch_priv {
 #define ECC_BCH8	1
 #define ECC_BCH16	2
 
-/* BCH nibbles for diff bch levels */
-#define ECC_BCH4_NIBBLES	13
-#define ECC_BCH8_NIBBLES	26
-#define ECC_BCH16_NIBBLES	52
-
 /*
  * This can be a single instance cause all current users have only one NAND
  * with nearly the same setup (BCH8, some with ELM and others with sw BCH

@@ -176,7 +170,6 @@ struct nand_bch_priv {
  */
 static __maybe_unused struct nand_bch_priv bch_priv = {
 	.type = ECC_BCH8,
-	.nibbles = ECC_BCH8_NIBBLES,
 	.control = NULL
 };
 

@@ -383,7 +376,8 @@ static int omap_correct_data_bch(struct mtd_info *mtd, uint8_t *dat,
 	}
 	/* use elm module to check for errors */
 	elm_config((enum bch_level)(bch->type));
-	if (elm_check_error(calc_ecc, bch->nibbles, &error_count, error_loc)) {
+	if (elm_check_error(calc_ecc, (enum bch_level)bch->type,
+					&error_count, error_loc)) {
 		printf("nand: error: uncorrectable ECC errors\n");
 		return -EINVAL;
 	}

index 45454ea..a6e9591 100644
@@ -68,7 +68,7 @@ struct elm {
 	struct location  error_location[8];	/* 0x800 */
 };
 
-int elm_check_error(u8 *syndrome, u32 nibbles, u32 *error_count,
+int elm_check_error(u8 *syndrome, enum bch_level bch_type, u32 *error_count,
 		u32 *error_locations);
 int elm_config(enum bch_level level);
 void elm_reset(void);

index a6e9591..b8096b0 100644
@@ -24,6 +24,9 @@
 #define ELM_LOCATION_STATUS_ECC_CORRECTABLE_MASK	(0x100)
 #define ELM_LOCATION_STATUS_ECC_NB_ERRORS_MASK		(0x1F)
 
+#define ELM_MAX_CHANNELS				8
+#define ELM_MAX_ERROR_COUNT				16
+
 #ifndef __ASSEMBLY__
 
 enum bch_level {

@@ -43,7 +46,7 @@ struct syndrome {
 struct location {
 	u32 location_status;		/* 0x800 */
 	u8 res1[124];			/* 0x804 */
-	u32 error_location_x[16];	/* 0x880.... */
+	u32 error_location_x[ELM_MAX_ERROR_COUNT]; /* 0x880, 0x980, .. */
 	u8 res2[64];			/* 0x8c0 */
 };
 

@@ -63,9 +66,9 @@ struct elm {
 	u8 res2[92];				/* 0x024 */
 	u32 page_ctrl;				/* 0x080 */
 	u8 res3[892];				/* 0x084 */
-	struct  syndrome syndrome_fragments[8]; /* 0x400 */
+	struct  syndrome syndrome_fragments[ELM_MAX_CHANNELS]; /* 0x400,0x420 */
 	u8 res4[512];				/* 0x600 */
-	struct location  error_location[8];	/* 0x800 */
+	struct location  error_location[ELM_MAX_CHANNELS]; /* 0x800,0x900 ... */
 };
 
 int elm_check_error(u8 *syndrome, enum bch_level bch_type, u32 *error_count,

index af38f00..4bd296e 100644
@@ -151,17 +151,10 @@ static int __maybe_unused omap_correct_data(struct mtd_info *mtd, uint8_t *dat,
  * Generic BCH interface
  */
 struct nand_bch_priv {
-	uint8_t mode;
-	uint8_t type;
 	struct bch_control *control;
 	enum omap_ecc ecc_scheme;
 };
 
-/* bch types */
-#define ECC_BCH4	0
-#define ECC_BCH8	1
-#define ECC_BCH16	2
-
 /*
  * This can be a single instance cause all current users have only one NAND
  * with nearly the same setup (BCH8, some with ELM and others with sw BCH

@@ -169,7 +162,6 @@ struct nand_bch_priv {
  * When some users with other BCH strength will exists this have to change!
  */
 static __maybe_unused struct nand_bch_priv bch_priv = {
-	.type = ECC_BCH8,
 	.control = NULL
 };
 

@@ -342,6 +334,7 @@ static int omap_correct_data_bch(struct mtd_info *mtd, uint8_t *dat,
 	uint32_t eccbytes = chip->ecc.bytes;
 	uint32_t error_count = 0, error_max;
 	uint32_t error_loc[8];
+	enum bch_level bch_type;
 	uint32_t i, ecc_flag = 0;
 	uint8_t count, err = 0;
 	uint32_t byte_pos, bit_pos;

@@ -369,22 +362,22 @@ static int omap_correct_data_bch(struct mtd_info *mtd, uint8_t *dat,
 	 */
 	switch (bch->ecc_scheme) {
 	case OMAP_ECC_BCH8_CODE_HW:
+		bch_type = BCH_8_BIT;
 		omap_reverse_list(calc_ecc, eccbytes - 1);
 		break;
 	default:
 		return -EINVAL;
 	}
 	/* use elm module to check for errors */
-	elm_config((enum bch_level)(bch->type));
-	if (elm_check_error(calc_ecc, (enum bch_level)bch->type,
-					&error_count, error_loc)) {
+	elm_config(bch_type);
+	if (elm_check_error(calc_ecc, bch_type, &error_count, error_loc)) {
 		printf("nand: error: uncorrectable ECC errors\n");
 		return -EINVAL;
 	}
 	/* correct bch error */
 	for (count = 0; count < error_count; count++) {
-		switch (bch->type) {
-		case ECC_BCH8:
+		switch (bch->ecc_scheme) {
+		case OMAP_ECC_BCH8_CODE_HW:
 			/* 14th byte in ECC is reserved to match ROM layout */
 			error_max = SECTOR_BYTES + (eccbytes - 1);
 			break;

@@ -562,7 +555,6 @@ static int omap_select_ecc_scheme(struct nand_chip *nand,
 		/* For this ecc-scheme, ecc.bytes, ecc.layout, ... are
 		 * initialized in nand_scan_tail(), so just set ecc.mode */
 		bch_priv.control	= NULL;
-		bch_priv.type		= 0;
 		nand->ecc.mode		= NAND_ECC_SOFT;
 		nand->ecc.layout	= NULL;
 		nand->ecc.size		= 0;

@@ -578,7 +570,6 @@ static int omap_select_ecc_scheme(struct nand_chip *nand,
 			return -EINVAL;
 		}
 		bch_priv.control	= NULL;
-		bch_priv.type		= 0;
 		/* populate ecc specific fields */
 		memset(&nand->ecc, 0, sizeof(struct nand_ecc_ctrl));
 		nand->ecc.mode		= NAND_ECC_HW;

@@ -617,7 +608,6 @@ static int omap_select_ecc_scheme(struct nand_chip *nand,
 			printf("nand: error: could not init_bch()\n");
 			return -ENODEV;
 		}
-		bch_priv.type = ECC_BCH8;
 		/* populate ecc specific fields */
 		memset(&nand->ecc, 0, sizeof(struct nand_ecc_ctrl));
 		nand->ecc.mode		= NAND_ECC_HW;

@@ -659,7 +649,6 @@ static int omap_select_ecc_scheme(struct nand_chip *nand,
 		}
 		/* intialize ELM for ECC error detection */
 		elm_init();
-		bch_priv.type		= ECC_BCH8;
 		/* populate ecc specific fields */
 		memset(&nand->ecc, 0, sizeof(struct nand_ecc_ctrl));
 		nand->ecc.mode		= NAND_ECC_HW;

index 4bd296e..ae8fbb4 100644
@@ -148,9 +148,9 @@ static int __maybe_unused omap_correct_data(struct mtd_info *mtd, uint8_t *dat,
 }
 
 /*
- * Generic BCH interface
+ * Driver configurations
  */
-struct nand_bch_priv {
+struct omap_nand_info {
 	struct bch_control *control;
 	enum omap_ecc ecc_scheme;
 };

@@ -161,7 +161,7 @@ struct nand_bch_priv {
  * library).
  * When some users with other BCH strength will exists this have to change!
  */
-static __maybe_unused struct nand_bch_priv bch_priv = {
+static __maybe_unused struct omap_nand_info omap_nand_info = {
 	.control = NULL
 };
 

@@ -191,7 +191,7 @@ __maybe_unused
 static void omap_enable_hwecc(struct mtd_info *mtd, int32_t mode)
 {
 	struct nand_chip	*nand	= mtd->priv;
-	struct nand_bch_priv	*bch	= nand->priv;
+	struct omap_nand_info	*info	= nand->priv;
 	unsigned int dev_width = (nand->options & NAND_BUSWIDTH_16) ? 1 : 0;
 	unsigned int ecc_algo = 0;
 	unsigned int bch_type = 0;

@@ -200,7 +200,7 @@ static void omap_enable_hwecc(struct mtd_info *mtd, int32_t mode)
 	u32 ecc_config_val = 0;
 
 	/* configure GPMC for specific ecc-scheme */
-	switch (bch->ecc_scheme) {
+	switch (info->ecc_scheme) {
 	case OMAP_ECC_HAM1_CODE_SW:
 		return;
 	case OMAP_ECC_HAM1_CODE_HW:

@@ -262,11 +262,11 @@ static int omap_calculate_ecc(struct mtd_info *mtd, const uint8_t *dat,
 				uint8_t *ecc_code)
 {
 	struct nand_chip *chip = mtd->priv;
-	struct nand_bch_priv *bch = chip->priv;
+	struct omap_nand_info *info = chip->priv;
 	uint32_t *ptr, val = 0;
 	int8_t i = 0, j;
 
-	switch (bch->ecc_scheme) {
+	switch (info->ecc_scheme) {
 	case OMAP_ECC_HAM1_CODE_HW:
 		val = readl(&gpmc_cfg->ecc1_result);
 		ecc_code[0] = val & 0xFF;

@@ -294,7 +294,7 @@ static int omap_calculate_ecc(struct mtd_info *mtd, const uint8_t *dat,
 		return -EINVAL;
 	}
 	/* ECC scheme specific syndrome customizations */
-	switch (bch->ecc_scheme) {
+	switch (info->ecc_scheme) {
 	case OMAP_ECC_HAM1_CODE_HW:
 		break;
 #ifdef CONFIG_BCH

@@ -330,7 +330,7 @@ static int omap_correct_data_bch(struct mtd_info *mtd, uint8_t *dat,
 				uint8_t *read_ecc, uint8_t *calc_ecc)
 {
 	struct nand_chip *chip = mtd->priv;
-	struct nand_bch_priv *bch = chip->priv;
+	struct omap_nand_info *info = chip->priv;
 	uint32_t eccbytes = chip->ecc.bytes;
 	uint32_t error_count = 0, error_max;
 	uint32_t error_loc[8];

@@ -360,7 +360,7 @@ static int omap_correct_data_bch(struct mtd_info *mtd, uint8_t *dat,
 	 * while reading ECC result we read it in big endian.
 	 * Hence while loading to ELM we have rotate to get the right endian.
 	 */
-	switch (bch->ecc_scheme) {
+	switch (info->ecc_scheme) {
 	case OMAP_ECC_BCH8_CODE_HW:
 		bch_type = BCH_8_BIT;
 		omap_reverse_list(calc_ecc, eccbytes - 1);

@@ -376,7 +376,7 @@ static int omap_correct_data_bch(struct mtd_info *mtd, uint8_t *dat,
 	}
 	/* correct bch error */
 	for (count = 0; count < error_count; count++) {
-		switch (bch->ecc_scheme) {
+		switch (info->ecc_scheme) {
 		case OMAP_ECC_BCH8_CODE_HW:
 			/* 14th byte in ECC is reserved to match ROM layout */
 			error_max = SECTOR_BYTES + (eccbytes - 1);

@@ -483,10 +483,10 @@ static int omap_correct_data_bch_sw(struct mtd_info *mtd, u_char *data,
 	/* cannot correct more than 8 errors */
 	unsigned int errloc[8];
 	struct nand_chip *chip = mtd->priv;
-	struct nand_bch_priv *chip_priv = chip->priv;
-	struct bch_control *bch = chip_priv->control;
+	struct omap_nand_info *info = chip->priv;
 
-	count = decode_bch(bch, NULL, 512, read_ecc, calc_ecc, NULL, errloc);
+	count = decode_bch(info->control, NULL, 512, read_ecc, calc_ecc,
+							NULL, errloc);
 	if (count > 0) {
 		/* correct errors */
 		for (i = 0; i < count; i++) {

@@ -522,15 +522,11 @@ static int omap_correct_data_bch_sw(struct mtd_info *mtd, u_char *data,
 static void __maybe_unused omap_free_bch(struct mtd_info *mtd)
 {
 	struct nand_chip *chip = mtd->priv;
-	struct nand_bch_priv *chip_priv = chip->priv;
-	struct bch_control *bch = NULL;
+	struct omap_nand_info *info = chip->priv;
 
-	if (chip_priv)
-		bch = chip_priv->control;
-
-	if (bch) {
-		free_bch(bch);
-		chip_priv->control = NULL;
+	if (info->control) {
+		free_bch(info->control);
+		info->control = NULL;
 	}
 }
 #endif /* CONFIG_BCH */

@@ -544,7 +540,7 @@ static void __maybe_unused omap_free_bch(struct mtd_info *mtd)
  */
 static int omap_select_ecc_scheme(struct nand_chip *nand,
 	enum omap_ecc ecc_scheme, unsigned int pagesize, unsigned int oobsize) {
-	struct nand_bch_priv	*bch		= nand->priv;
+	struct omap_nand_info	*info		= nand->priv;
 	struct nand_ecclayout	*ecclayout	= &omap_ecclayout;
 	int eccsteps = pagesize / SECTOR_BYTES;
 	int i;

@@ -554,11 +550,10 @@ static int omap_select_ecc_scheme(struct nand_chip *nand,
 		debug("nand: selected OMAP_ECC_HAM1_CODE_SW\n");
 		/* For this ecc-scheme, ecc.bytes, ecc.layout, ... are
 		 * initialized in nand_scan_tail(), so just set ecc.mode */
-		bch_priv.control	= NULL;
+		info->control		= NULL;
 		nand->ecc.mode		= NAND_ECC_SOFT;
 		nand->ecc.layout	= NULL;
 		nand->ecc.size		= 0;
-		bch->ecc_scheme		= OMAP_ECC_HAM1_CODE_SW;
 		break;
 
 	case OMAP_ECC_HAM1_CODE_HW:

@@ -569,7 +564,7 @@ static int omap_select_ecc_scheme(struct nand_chip *nand,
 				(3 * eccsteps) + BADBLOCK_MARKER_LENGTH));
 			return -EINVAL;
 		}
-		bch_priv.control	= NULL;
+		info->control		= NULL;
 		/* populate ecc specific fields */
 		memset(&nand->ecc, 0, sizeof(struct nand_ecc_ctrl));
 		nand->ecc.mode		= NAND_ECC_HW;

@@ -590,7 +585,6 @@ static int omap_select_ecc_scheme(struct nand_chip *nand,
 		ecclayout->oobfree[0].offset = i + BADBLOCK_MARKER_LENGTH;
 		ecclayout->oobfree[0].length = oobsize - ecclayout->eccbytes -
 						BADBLOCK_MARKER_LENGTH;
-		bch->ecc_scheme		= OMAP_ECC_HAM1_CODE_HW;
 		break;
 
 	case OMAP_ECC_BCH8_CODE_HW_DETECTION_SW:

@@ -603,8 +597,8 @@ static int omap_select_ecc_scheme(struct nand_chip *nand,
 			return -EINVAL;
 		}
 		/* check if BCH S/W library can be used for error detection */
-		bch_priv.control = init_bch(13, 8, 0x201b);
-		if (!bch_priv.control) {
+		info->control = init_bch(13, 8, 0x201b);
+		if (!info->control) {
 			printf("nand: error: could not init_bch()\n");
 			return -ENODEV;
 		}

@@ -631,7 +625,6 @@ static int omap_select_ecc_scheme(struct nand_chip *nand,
 		ecclayout->oobfree[0].offset = i + BADBLOCK_MARKER_LENGTH;
 		ecclayout->oobfree[0].length = oobsize - ecclayout->eccbytes -
 						BADBLOCK_MARKER_LENGTH;
-		bch->ecc_scheme		= OMAP_ECC_BCH8_CODE_HW_DETECTION_SW;
 		break;
 #else
 		printf("nand: error: CONFIG_BCH required for ECC\n");

@@ -649,6 +642,7 @@ static int omap_select_ecc_scheme(struct nand_chip *nand,
 		}
 		/* intialize ELM for ECC error detection */
 		elm_init();
+		info->control		= NULL;
 		/* populate ecc specific fields */
 		memset(&nand->ecc, 0, sizeof(struct nand_ecc_ctrl));
 		nand->ecc.mode		= NAND_ECC_HW;

@@ -666,7 +660,6 @@ static int omap_select_ecc_scheme(struct nand_chip *nand,
 		ecclayout->oobfree[0].offset = i + BADBLOCK_MARKER_LENGTH;
 		ecclayout->oobfree[0].length = oobsize - ecclayout->eccbytes -
 						BADBLOCK_MARKER_LENGTH;
-		bch->ecc_scheme		= OMAP_ECC_BCH8_CODE_HW;
 		break;
 #else
 		printf("nand: error: CONFIG_NAND_OMAP_ELM required for ECC\n");

@@ -682,6 +675,7 @@ static int omap_select_ecc_scheme(struct nand_chip *nand,
 	if (ecc_scheme != OMAP_ECC_HAM1_CODE_SW)
 		nand->ecc.layout = ecclayout;
 
+	info->ecc_scheme = ecc_scheme;
 	return 0;
 }
 

@@ -785,7 +779,7 @@ int board_nand_init(struct nand_chip *nand)
 
 	nand->IO_ADDR_R = (void __iomem *)&gpmc_cfg->cs[cs].nand_dat;
 	nand->IO_ADDR_W = (void __iomem *)&gpmc_cfg->cs[cs].nand_cmd;
-	nand->priv	= &bch_priv;
+	nand->priv	= &omap_nand_info;
 	nand->cmd_ctrl	= omap_nand_hwcontrol;
 	nand->options	|= NAND_NO_PADDING | NAND_CACHEPRG;
 	/* If we are 16 bit dev, our gpmc config tells us that */

index ae8fbb4..b1be8eb 100644
@@ -331,7 +331,7 @@ static int omap_correct_data_bch(struct mtd_info *mtd, uint8_t *dat,
 {
 	struct nand_chip *chip = mtd->priv;
 	struct omap_nand_info *info = chip->priv;
-	uint32_t eccbytes = chip->ecc.bytes;
+	struct nand_ecc_ctrl *ecc = &chip->ecc;
 	uint32_t error_count = 0, error_max;
 	uint32_t error_loc[8];
 	enum bch_level bch_type;

@@ -340,7 +340,7 @@ static int omap_correct_data_bch(struct mtd_info *mtd, uint8_t *dat,
 	uint32_t byte_pos, bit_pos;
 
 	/* check calculated ecc */
-	for (i = 0; i < chip->ecc.bytes && !ecc_flag; i++) {
+	for (i = 0; i < ecc->bytes && !ecc_flag; i++) {
 		if (calc_ecc[i] != 0x00)
 			ecc_flag = 1;
 	}

@@ -349,7 +349,7 @@ static int omap_correct_data_bch(struct mtd_info *mtd, uint8_t *dat,
 
 	/* check for whether its a erased-page */
 	ecc_flag = 0;
-	for (i = 0; i < chip->ecc.bytes && !ecc_flag; i++) {
+	for (i = 0; i < ecc->bytes && !ecc_flag; i++) {
 		if (read_ecc[i] != 0xff)
 			ecc_flag = 1;
 	}

@@ -363,7 +363,7 @@ static int omap_correct_data_bch(struct mtd_info *mtd, uint8_t *dat,
 	switch (info->ecc_scheme) {
 	case OMAP_ECC_BCH8_CODE_HW:
 		bch_type = BCH_8_BIT;
-		omap_reverse_list(calc_ecc, eccbytes - 1);
+		omap_reverse_list(calc_ecc, ecc->bytes - 1);
 		break;
 	default:
 		return -EINVAL;

@@ -379,7 +379,7 @@ static int omap_correct_data_bch(struct mtd_info *mtd, uint8_t *dat,
 		switch (info->ecc_scheme) {
 		case OMAP_ECC_BCH8_CODE_HW:
 			/* 14th byte in ECC is reserved to match ROM layout */
-			error_max = SECTOR_BYTES + (eccbytes - 1);
+			error_max = SECTOR_BYTES + (ecc->bytes - 1);
 			break;
 		default:
 			return -EINVAL;

index afa629a..d963e6c 100644
@@ -19,6 +19,7 @@
 #include <linux/mtd/omap_elm.h>
 #include <asm/arch/hardware.h>
 
+#define DRIVER_NAME		"omap-elm"
 #define ELM_DEFAULT_POLY (0)
 
 struct elm *elm_cfg;

@@ -113,8 +114,10 @@ int elm_check_error(u8 *syndrome, enum bch_level bch_type, u32 *error_count,
 
 	/* check if correctable */
 	location_status = readl(&elm_cfg->error_location[poly].location_status);
-	if (!(location_status & ELM_LOCATION_STATUS_ECC_CORRECTABLE_MASK))
-		return -1;
+	if (!(location_status & ELM_LOCATION_STATUS_ECC_CORRECTABLE_MASK)) {
+		printf("%s: uncorrectable ECC errors\n", DRIVER_NAME);
+		return -EBADMSG;
+	}
 
 	/* get error count */
 	*error_count = readl(&elm_cfg->error_location[poly].location_status) &

index b1be8eb..325ebfd 100644
@@ -370,10 +370,10 @@ static int omap_correct_data_bch(struct mtd_info *mtd, uint8_t *dat,
 	}
 	/* use elm module to check for errors */
 	elm_config(bch_type);
-	if (elm_check_error(calc_ecc, bch_type, &error_count, error_loc)) {
-		printf("nand: error: uncorrectable ECC errors\n");
-		return -EINVAL;
-	}
+	err = elm_check_error(calc_ecc, bch_type, &error_count, error_loc);
+	if (err)
+		return err;
+
 	/* correct bch error */
 	for (count = 0; count < error_count; count++) {
 		switch (info->ecc_scheme) {