Renesas CMT, MTU2 and TMU timers DT support

Document DT bindings and parse them in the CMT driver.

Cc devicetree at vger.kernel.org

Signed-off-by Laurent Pinchart <[email protected]>

Tested-by Simon Horman <[email protected]>

---
 .../devicetree/bindings/timer/renesas,cmt.txt      | 47 +++++++++++++++
 drivers/clocksource/sh_cmt.c                       | 66 +++++++++++++------
 2 files changed, 95 insertions(+), 18 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/timer/renesas,cmt.txt

(quoted diff) +0 -0

b/Documentation/devicetree/bindings/timer/renesas,cmt.txt new file mode 100644
index 0000000..643cfff

Documentation/devicetree/bindings/timer/renesas,cmt.txt new file +3 -0

@@ -0,0 +1,47 @@
+* Renesas R-Car Compare Match Timer (CMT)
+
+The CMT is a multi-channel 16/32/48-bit timer/counter with configurable

clock

Documentation/devicetree/bindings/timer/renesas,cmt.txt new file +4 -0

+inputs and programmable compare match.
+
+Channels share hardware resources but their counter and compare match value
+are independent. A particular CMT instance can implement only a subset of

the

Documentation/devicetree/bindings/timer/renesas,cmt.txt new file +2 -0

+channels supported by the CMT model. Channel indices represent the hardware
+position of the channel in the CMT and don't match the channel numbers in

the

Documentation/devicetree/bindings/timer/renesas,cmt.txt new file +5 -0

+		(CMT1 on sh7372, sh73a0 and r8a7740)
+    - "renesas,cmt-48-gen2" for the second generation 48-bit CMT
+		(CMT[01] on r8a73a4, r8a7790 and r8a7791)
+
+  - reg: base address and length of the registers block for the timer

module.

Documentation/devicetree/bindings/timer/renesas,cmt.txt new file +23 -0

+  - interrupts: interrupt-specifier for the timer, one per channel.
+  - clocks: a list of phandle + clock-specifier pairs, one for each entry
+    in clock-names.
+  - clock-names: must contain "fck" for the functional clock.
+
+  - renesas,channels-mask: bitmask of the available channels.
+
+
+Example: R8A7790 (R-Car H2) CMT0 node
+
+	CMT0 on R8A7790 implements hardware channels 5 and 6 only and names
+	them channels 0 and 1 in the documentation.
+
+	cmt0: timer at ffca0000 {
+		compatible = "renesas,cmt-48-gen2";
+		reg = <0 0xffca0000 0 0x1004>;
+		interrupts = <0 142 IRQ_TYPE_LEVEL_HIGH>,
+			     <0 142 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&mstp1_clks R8A7790_CLK_CMT0>;
+		clock-names = "fck";
+
+		renesas,channels-mask = <0x60>;
+	};

drivers/clocksource/sh_cmt.c +15 -0

index 4d00e4b..09a93c4 100644
@@ -24,6 +24,7 @@
 #include <linux/ioport.h>
 #include <linux/irq.h>
 #include <linux/module.h>
+#include <linux/of.h>
 #include <linux/platform_device.h>
 #include <linux/pm_domain.h>
 #include <linux/pm_runtime.h>

@@ -122,6 +123,7 @@ struct sh_cmt_device {
 
 	struct sh_cmt_channel *channels;
 	unsigned int num_channels;
+	unsigned int hw_channels;
 
 	bool has_clockevent;
 	bool has_clocksource;

@@ -924,10 +926,35 @@ static int sh_cmt_map_memory(struct sh_cmt_device
 *cmt) return 0;
 }
 
+static const struct platform_device_id sh_cmt_id_table[] = {
+	{ "sh-cmt-16", (kernel_ulong_t)&sh_cmt_info[SH_CMT_16BIT] },
+	{ "sh-cmt-32", (kernel_ulong_t)&sh_cmt_info[SH_CMT_32BIT] },
+	{ "sh-cmt-32-fast", (kernel_ulong_t)&sh_cmt_info[SH_CMT_32BIT_FAST] },
+	{ "sh-cmt-48", (kernel_ulong_t)&sh_cmt_info[SH_CMT_48BIT] },
+	{ "sh-cmt-48-gen2", (kernel_ulong_t)&sh_cmt_info[SH_CMT_48BIT_GEN2] },
+	{ }
+};
+MODULE_DEVICE_TABLE(platform, sh_cmt_id_table);
+
+static const struct of_device_id sh_cmt_of_table[] __maybe_unused = {
+	{ .compatible = "renesas,cmt-32", .data = &sh_cmt_info[SH_CMT_32BIT] },
+	{ .compatible = "renesas,cmt-32-fast", .data =
 &sh_cmt_info[SH_CMT_32BIT_FAST] }, +	{ .compatible = "renasas,cmt-48",

.data = &sh_cmt_info[SH_CMT_48BIT] }, + { .compatible =
"renesas,cmt-48-gen2", .data = &sh_cmt_info[SH_CMT_48BIT_GEN2] }, + { }

drivers/clocksource/sh_cmt.c +11 -0

+};
+MODULE_DEVICE_TABLE(of, sh_cmt_of_table);
+
+static int sh_cmt_parse_dt(struct sh_cmt_device *cmt)
+{
+	struct device_node *np = cmt->pdev->dev.of_node;
+
+	return of_property_read_u32(np, "renesas,channels-mask",
+				    &cmt->hw_channels);
+}
+
 static int sh_cmt_setup(struct sh_cmt_device *cmt, struct platform_device

*pdev) {

drivers/clocksource/sh_cmt.c +17 -7

-	struct sh_timer_config *cfg = pdev->dev.platform_data;
-	const struct platform_device_id *id = pdev->id_entry;
 	unsigned int mask;
 	unsigned int i;
 	int ret;

@@ -936,13 +963,26 @@ static int sh_cmt_setup(struct sh_cmt_device *cmt,
 struct platform_device *pdev) cmt->pdev = pdev;
 	raw_spin_lock_init(&cmt->lock);
 
-	if (!cfg) {
+	if (IS_ENABLED(CONFIG_OF) && pdev->dev.of_node) {
+		const struct of_device_id *id;
+
+		id = of_match_node(sh_cmt_of_table, pdev->dev.of_node);
+		cmt->info = id->data;
+
+		ret = sh_cmt_parse_dt(cmt);
+		if (ret < 0)
+			return ret;
+	} else if (pdev->dev.platform_data) {
+		struct sh_timer_config *cfg = pdev->dev.platform_data;
+		const struct platform_device_id *id = pdev->id_entry;
+
+		cmt->info = (const struct sh_cmt_info *)id->driver_data;
+		cmt->hw_channels = cfg->channels_mask;
+	} else {
 		dev_err(&cmt->pdev->dev, "missing platform data\n");
 		return -ENXIO;
 	}
 
-	cmt->info = (const struct sh_cmt_info *)id->driver_data;
-
 	/* Get hold of clock. */
 	cmt->clk = clk_get(&cmt->pdev->dev, "fck");
 	if (IS_ERR(cmt->clk)) {

@@ -960,8 +1000,7 @@ static int sh_cmt_setup(struct sh_cmt_device *cmt,
 struct platform_device *pdev) goto err_clk_unprepare;
 
 	/* Allocate and setup the channels. */
-	cmt->num_channels = hweight8(cfg->channels_mask);
-
+	cmt->num_channels = hweight8(cmt->hw_channels);
 	cmt->channels = kzalloc(cmt->num_channels * sizeof(*cmt->channels),
 				GFP_KERNEL);
 	if (cmt->channels == NULL) {

@@ -973,7 +1012,7 @@ static int sh_cmt_setup(struct sh_cmt_device *cmt,

struct platform_device *pdev) * Use the first channel as a clock event device and the second channel * as a clock source. If only one channel is available use it for both. */

drivers/clocksource/sh_cmt.c +2 -11

-	for (i = 0, mask = cfg->channels_mask; i < cmt->num_channels; ++i) {
+	for (i = 0, mask = cmt->hw_channels; i < cmt->num_channels; ++i) {
 		unsigned int hwidx = ffs(mask) - 1;
 		bool clocksource = i == 1 || cmt->num_channels == 1;
 		bool clockevent = i == 0;

@@ -1044,21 +1083,12 @@ static int sh_cmt_remove(struct platform_device
 *pdev) return -EBUSY; /* cannot unregister clockevent and clocksource */ }
 
-static const struct platform_device_id sh_cmt_id_table[] = {
-	{ "sh-cmt-16", (kernel_ulong_t)&sh_cmt_info[SH_CMT_16BIT] },
-	{ "sh-cmt-32", (kernel_ulong_t)&sh_cmt_info[SH_CMT_32BIT] },
-	{ "sh-cmt-32-fast", (kernel_ulong_t)&sh_cmt_info[SH_CMT_32BIT_FAST] },
-	{ "sh-cmt-48", (kernel_ulong_t)&sh_cmt_info[SH_CMT_48BIT] },
-	{ "sh-cmt-48-gen2", (kernel_ulong_t)&sh_cmt_info[SH_CMT_48BIT_GEN2] },
-	{ }
-};
-MODULE_DEVICE_TABLE(platform, sh_cmt_id_table);
-
 static struct platform_driver sh_cmt_device_driver = {
 	.probe		= sh_cmt_probe,
 	.remove		= sh_cmt_remove,
 	.driver		= {
 		.name	= "sh_cmt",
+		.of_match_table = of_match_ptr(sh_cmt_of_table),
 	},
 	.id_table	= sh_cmt_id_table,
 };

Document DT bindings and parse them in the TMU driver.

Cc devicetree at vger.kernel.org

Signed-off-by Laurent Pinchart <[email protected]>

---
 .../devicetree/bindings/timer/renesas,tmu.txt      | 39 +++++++++++++++++
 drivers/clocksource/sh_tmu.c                       | 51 +++++++++++++++++-----
 2 files changed, 80 insertions(+), 10 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/timer/renesas,tmu.txt

Documentation/devicetree/bindings/timer/renesas,tmu.txt new file +39 -0

new file mode 100644
index 0000000..425d0c5
@@ -0,0 +1,39 @@
+* Renesas R-Car Timer Unit (TMU)
+
+The TMU is a 32-bit timer/counter with configurable clock inputs and
+programmable compare match.
+
+Channels share hardware resources but their counter and compare match value
+are independent. The TMU hardware supports up to three channels.
+
+Required Properties:
+
+  - compatible: must contain "renesas,tmu"
+
+  - reg: base address and length of the registers block for the timer module.
+
+  - interrupts: interrupt-specifier for the timer, one per channel.
+
+  - clocks: a list of phandle + clock-specifier pairs, one for each entry
+    in clock-names.
+  - clock-names: must contain "fck" for the functional clock.
+
+Optional Properties:
+
+  - #renesas,channels: number of channels implemented by the timer, must be 2
+    or 3 (if not specified the value defaults to 3).
+
+
+Example: R8A7779 (R-Car H1) TMU0 node
+
+	tmu0: timer at ffd80000 {
+		compatible = "renesas,tmu";
+		reg = <0xffd80000 0x30>;
+		interrupts = <0 32 IRQ_TYPE_LEVEL_HIGH>,
+			     <0 33 IRQ_TYPE_LEVEL_HIGH>,
+			     <0 34 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&mstp0_clks R8A7779_CLK_TMU0>;
+		clock-names = "fck";
+
+		#renesas,channels = <3>;
+	};

drivers/clocksource/sh_tmu.c +41 -10

index ef8fb0b..ed61ed2 100644
@@ -24,6 +24,7 @@
 #include <linux/ioport.h>
 #include <linux/irq.h>
 #include <linux/module.h>
+#include <linux/of.h>
 #include <linux/platform_device.h>
 #include <linux/pm_domain.h>
 #include <linux/pm_runtime.h>

@@ -509,23 +510,48 @@ static int sh_tmu_map_memory(struct sh_tmu_device *tmu)
 	return 0;
 }
 
+static int sh_tmu_parse_dt(struct sh_tmu_device *tmu)
+{
+	struct device_node *np = tmu->pdev->dev.of_node;
+
+	tmu->model = SH_TMU;
+	tmu->num_channels = 3;
+
+	of_property_read_u32(np, "#renesas,channels", &tmu->num_channels);
+
+	if (tmu->num_channels != 2 && tmu->num_channels != 3) {
+		dev_err(&tmu->pdev->dev, "invalid number of channels %u\n",
+			tmu->num_channels);
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
 static int sh_tmu_setup(struct sh_tmu_device *tmu, struct platform_device *pdev)
 {
-	struct sh_timer_config *cfg = pdev->dev.platform_data;
-	const struct platform_device_id *id = pdev->id_entry;
 	unsigned int i;
 	int ret;
 
-	if (!cfg) {
-		dev_err(&tmu->pdev->dev, "missing platform data\n");
-		return -ENXIO;
-	}
-
 	tmu->pdev = pdev;
-	tmu->model = id->driver_data;
 
 	raw_spin_lock_init(&tmu->lock);
 
+	if (IS_ENABLED(CONFIG_OF) && pdev->dev.of_node) {
+		ret = sh_tmu_parse_dt(tmu);
+		if (ret < 0)
+			return ret;
+	} else if (pdev->dev.platform_data) {
+		const struct platform_device_id *id = pdev->id_entry;
+		struct sh_timer_config *cfg = pdev->dev.platform_data;
+
+		tmu->model = id->driver_data;
+		tmu->num_channels = hweight8(cfg->channels_mask);
+	} else {
+		dev_err(&tmu->pdev->dev, "missing platform data\n");
+		return -ENXIO;
+	}
+
 	/* Get hold of clock. */
 	tmu->clk = clk_get(&tmu->pdev->dev, "fck");
 	if (IS_ERR(tmu->clk)) {

@@ -545,8 +571,6 @@ static int sh_tmu_setup(struct sh_tmu_device *tmu, struct platform_device *pdev)
 	}
 
 	/* Allocate and setup the channels. */
-	tmu->num_channels = hweight8(cfg->channels_mask);
-
 	tmu->channels = kzalloc(sizeof(*tmu->channels) * tmu->num_channels,
 				GFP_KERNEL);
 	if (tmu->channels == NULL) {

@@ -630,11 +654,18 @@ static const struct platform_device_id sh_tmu_id_table[] = {
 };
 MODULE_DEVICE_TABLE(platform, sh_tmu_id_table);
 
+static const struct of_device_id sh_tmu_of_table[] __maybe_unused = {
+	{ .compatible = "renesas,tmu" },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, sh_tmu_of_table);
+
 static struct platform_driver sh_tmu_device_driver = {
 	.probe		= sh_tmu_probe,
 	.remove		= sh_tmu_remove,
 	.driver		= {
 		.name	= "sh_tmu",
+		.of_match_table = of_match_ptr(sh_tmu_of_table),
 	},
 	.id_table	= sh_tmu_id_table,
 };

Signature · 6 lines

1.8.5.5

--
To unsubscribe from this list: send the line "unsubscribe linux-sh" in
the body of a message to majordomo at vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Add the TMU0, TMU1 and TMU2 counters to the r8a7779 device tree and make them disabled by default.

Signed-off-by Laurent Pinchart <[email protected]>

---
 arch/arm/boot/dts/r8a7779.dtsi | 42 ++++++++++++++++++++++++++++++++++++++++++
 1 file changed, 42 insertions(+)

arch/arm/boot/dts/r8a7779.dtsi +42 -0

index 94e2fc8..671d8e4 100644
@@ -266,6 +266,48 @@
 		reg = <0xffc48000 0x38>;
 	};
 
+	tmu0: timer at ffd80000 {
+		compatible = "renesas,tmu";
+		reg = <0xffd80000 0x30>;
+		interrupts = <0 32 IRQ_TYPE_LEVEL_HIGH>,
+			     <0 33 IRQ_TYPE_LEVEL_HIGH>,
+			     <0 34 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&mstp0_clks R8A7779_CLK_TMU0>;
+		clock-names = "fck";
+
+		#renesas,channels = <3>;
+
+		status = "disabled";
+	};
+
+	tmu1: timer at ffd81000 {
+		compatible = "renesas,tmu";
+		reg = <0xffd81000 0x30>;
+		interrupts = <0 36 IRQ_TYPE_LEVEL_HIGH>,
+			     <0 37 IRQ_TYPE_LEVEL_HIGH>,
+			     <0 38 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&mstp0_clks R8A7779_CLK_TMU1>;
+		clock-names = "fck";
+
+		#renesas,channels = <3>;
+
+		status = "disabled";
+	};
+
+	tmu2: timer at ffd82000 {
+		compatible = "renesas,tmu";
+		reg = <0xffd82000 0x30>;
+		interrupts = <0 40 IRQ_TYPE_LEVEL_HIGH>,
+			     <0 41 IRQ_TYPE_LEVEL_HIGH>,
+			     <0 42 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&mstp0_clks R8A7779_CLK_TMU2>;
+		clock-names = "fck";
+
+		#renesas,channels = <3>;
+
+		status = "disabled";
+	};
+
 	sata: sata at fc600000 {
 		compatible = "renesas,rcar-sata";
 		reg = <0xfc600000 0x2000>;

Signature · 6 lines

1.8.5.5

--
To unsubscribe from this list: send the line "unsubscribe linux-sh" in
the body of a message to majordomo at vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

No more device needs to be added from platform code when booting the reference platform, remove the now empty r8a7779_add_standard_devices_dt() function completely.

Signed-off-by Laurent Pinchart <[email protected]>

---
 arch/arm/boot/dts/r8a7779-marzen.dts            |  4 ++++
 arch/arm/mach-shmobile/board-marzen-reference.c | 10 ----------
 arch/arm/mach-shmobile/include/mach/r8a7779.h   |  1 -
 arch/arm/mach-shmobile/setup-r8a7779.c          | 17 +++++------------
 4 files changed, 9 insertions(+), 23 deletions(-)

arch/arm/boot/dts/r8a7779-marzen.dts +4 -0

index 20b1768..6025822 100644
@@ -78,6 +78,10 @@
 	clock-frequency = <31250000>;
 };
 
+&tmu0 {
+	status = "okay";
+};
+
 &pfc {
 	lan0_pins: lan0 {
 		intc {

arch/arm/mach-shmobile/board-marzen-reference.c +0 -10

index 670e48a..29bd384 100644
@@ -35,18 +35,8 @@ static void __init marzen_init_timer(void)
 	clocksource_of_init();
 }
 
-/*
- * This is a really crude hack to provide clkdev support to platform
- * devices until they get moved to DT.
- */
-static const struct clk_name clk_names[] __initconst = {
-	{ "tmu0", "fck", "sh-tmu.0" },
-};
-
 static void __init marzen_init(void)
 {
-	shmobile_clk_workaround(clk_names, ARRAY_SIZE(clk_names), false);
-	r8a7779_add_standard_devices_dt();
 	of_platform_populate(NULL, of_default_bus_match_table, NULL, NULL);
 	r8a7779_init_irq_extpin_dt(1); /* IRQ1 as individual interrupt */
 }

arch/arm/mach-shmobile/include/mach/r8a7779.h +0 -1

index e443c54..9e8c68e 100644
@@ -28,7 +28,6 @@ extern void r8a7779_map_io(void);
 extern void r8a7779_earlytimer_init(void);
 extern void r8a7779_add_early_devices(void);
 extern void r8a7779_add_standard_devices(void);
-extern void r8a7779_add_standard_devices_dt(void);
 extern void r8a7779_init_late(void);
 extern u32 r8a7779_read_mode_pins(void);
 extern void r8a7779_clock_init(void);

arch/arm/mach-shmobile/setup-r8a7779.c +5 -12

index e0050ab0..dcb8d18 100644
@@ -639,7 +639,7 @@ static void __init r8a7779_register_hpb_dmae(void)
 					  sizeof(dma_platform_data));
 }
 
-static struct platform_device *r8a7779_devices_dt[] __initdata = {
+static struct platform_device *r8a7779_early_devices[] __initdata = {
 	&tmu0_device,
 };
 

@@ -667,8 +667,8 @@ void __init r8a7779_add_standard_devices(void)
 
 	r8a7779_init_pm_domains();
 
-	platform_add_devices(r8a7779_devices_dt,
-			    ARRAY_SIZE(r8a7779_devices_dt));
+	platform_add_devices(r8a7779_early_devices,
+			    ARRAY_SIZE(r8a7779_early_devices));
 	platform_add_devices(r8a7779_standard_devices,
 			    ARRAY_SIZE(r8a7779_standard_devices));
 	r8a7779_register_hpb_dmae();

@@ -676,8 +676,8 @@ void __init r8a7779_add_standard_devices(void)
 
 void __init r8a7779_add_early_devices(void)
 {
-	early_platform_add_devices(r8a7779_devices_dt,
-				   ARRAY_SIZE(r8a7779_devices_dt));
+	early_platform_add_devices(r8a7779_early_devices,
+				   ARRAY_SIZE(r8a7779_early_devices));
 
 	/* Early serial console setup is not included here due to
 	 * memory map collisions. The SCIF serial ports in r8a7779

@@ -737,12 +737,6 @@ void __init r8a7779_init_irq_dt(void)
 	__raw_writel(0x003fee3f, INT2SMSKCR4);
 }
 
-void __init r8a7779_add_standard_devices_dt(void)
-{
-	platform_add_devices(r8a7779_devices_dt,
-			     ARRAY_SIZE(r8a7779_devices_dt));
-}
-
 #define MODEMR		0xffcc0020
 
 u32 __init r8a7779_read_mode_pins(void)

@@ -771,7 +765,6 @@ DT_MACHINE_START(R8A7779_DT, "Generic R8A7779 (Flattened Device Tree)")
 	.init_early	= shmobile_init_delay,
 	.nr_irqs	= NR_IRQS_LEGACY,
 	.init_irq	= r8a7779_init_irq_dt,
-	.init_machine	= r8a7779_add_standard_devices_dt,
 	.init_late	= r8a7779_init_late,
 	.dt_compat	= r8a7779_compat_dt,
 MACHINE_END

Signature · 6 lines

1.8.5.5

--
To unsubscribe from this list: send the line "unsubscribe linux-sh" in
the body of a message to majordomo at vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Hi Daniel,

Could you please pull the following changes and drop the first version of this pull request ? I've fixed one last typo noticed by Simon in patch 09/19.

As last time I have board and SoC changes that depend on the driver changes and that will need to go through Simon's tree. Could you thus please provide a stable branch based on one of the v3.16-rc tags ?

The following changes since commit 4c834452aad01531db949414f94f817a86348d59:

Linux 3.16-rc3 (2014-06-29 14:11:36 -0700)

are available in the git repository at:

git://linuxtv.org/pinchartl/fbdev.git timers/upstream/drivers

for you to fetch changes up to cca8d0596c4c7acb371ea1bc5eee9b404b30516a:

clocksource: sh_mtu2: Add DT support (2014-07-04 15:50:29 +0200)

----------------------------------------------------------------
Laurent Pinchart (10):
clocksource: sh_cmt: Drop support for legacy platform data
clocksource: sh_cmt: Replace global spinlock with a per-device
spinlock clocksource: sh_tmu: Drop support for legacy platform data
clocksource: sh_tmu: Replace global spinlock with a per-device
spinlock clocksource: sh_mtu2: Drop support for legacy platform data
clocksource: sh_mtu2: Replace global spinlock with a per-device
spinlock clocksource: shmobile: Remove unused sh_timer_config members
clocksource: sh_cmt: Add DT support
clocksource: sh_tmu: Add DT support
clocksource: sh_mtu2: Add DT support

 Documentation/devicetree/bindings/timer/renesas,cmt.txt |  47 +++++
 .../devicetree/bindings/timer/renesas,mtu2.txt          |  39 ++++
 Documentation/devicetree/bindings/timer/renesas,tmu.txt |  39 ++++
 drivers/clocksource/sh_cmt.c                            | 233 ++++++-------
 drivers/clocksource/sh_mtu2.c                           | 146 +++++--------
 drivers/clocksource/sh_tmu.c                            | 127 ++++++-------
 include/linux/sh_timer.h                                |   5 -
 7 files changed, 309 insertions(+), 327 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/timer/renesas,cmt.txt
 create mode 100644 Documentation/devicetree/bindings/timer/renesas,mtu2.txt
 create mode 100644 Documentation/devicetree/bindings/timer/renesas,tmu.txt

Hi Daniel,

Quoted 6 lines · On Friday 04 July 2014 15:53:32 Laurent Pinchart wrote:

Hi Daniel,

Could you please pull the following changes and drop the first version of this pull request ? I've fixed one last typo noticed by Simon in patch 09/19.

Quoted 3 lines

As last time I have board and SoC changes that depend on the driver changes and that will need to go through Simon's tree. Could you thus please provide a stable branch based on one of the v3.16-rc tags ?

Given that I'd like to get the arch/ part of the change set in v3.17, could I ask you to fast track this pull request if possible ?

Quoted 37 lines

The following changes since commit 4c834452aad01531db949414f94f817a86348d59:

Linux 3.16-rc3 (2014-06-29 14:11:36 -0700)

are available in the git repository at:

git://linuxtv.org/pinchartl/fbdev.git timers/upstream/drivers

for you to fetch changes up to cca8d0596c4c7acb371ea1bc5eee9b404b30516a:

clocksource: sh_mtu2: Add DT support (2014-07-04 15:50:29 +0200)

----------------------------------------------------------------
Laurent Pinchart (10):
clocksource: sh_cmt: Drop support for legacy platform data
clocksource: sh_cmt: Replace global spinlock with a per-device
spinlock clocksource: sh_tmu: Drop support for legacy platform data
clocksource: sh_tmu: Replace global spinlock with a per-device
spinlock clocksource: sh_mtu2: Drop support for legacy platform data
clocksource: sh_mtu2: Replace global spinlock with a per-device
spinlock clocksource: shmobile: Remove unused sh_timer_config members
clocksource: sh_cmt: Add DT support
clocksource: sh_tmu: Add DT support
clocksource: sh_mtu2: Add DT support

 Documentation/devicetree/bindings/timer/renesas,cmt.txt |  47 +++++
 .../devicetree/bindings/timer/renesas,mtu2.txt          |  39 ++++
 Documentation/devicetree/bindings/timer/renesas,tmu.txt |  39 ++++
 drivers/clocksource/sh_cmt.c                            | 233 ++++++-------
 drivers/clocksource/sh_mtu2.c                           | 146 +++++--------
 drivers/clocksource/sh_tmu.c                            | 127 ++++++-------
 include/linux/sh_timer.h                                |   5 -
 7 files changed, 309 insertions(+), 327 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/timer/renesas,cmt.txt
 create mode 100644 Documentation/devicetree/bindings/timer/renesas,mtu2.txt
 create mode 100644 Documentation/devicetree/bindings/timer/renesas,tmu.txt

Signature · 8 lines

Regards,

Laurent Pinchart

--
To unsubscribe from this list: send the line "unsubscribe linux-sh" in
the body of a message to majordomo at vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[Cc Olof Johansson, ARM SoC Team]

Quoted 7 lines · Laurent Pinchart

Quoted 6 lines · On Friday 04 July 2014 15:53:32 Laurent Pinchart wrote:

Hi Daniel,

Could you please pull the following changes and drop the first version of this pull request ? I've fixed one last typo noticed by Simon in patch 09/19.

Quoted 6 lines

Quoted 3 lines

As last time I have board and SoC changes that depend on the driver changes and that will need to go through Simon's tree. Could you thus please provide a stable branch based on one of the v3.16-rc tags ?

Given that I'd like to get the arch/ part of the change set in v3.17, could I ask you to fast track this pull request if possible ?

Hi Laurent, Hi Daniel,

I am wondering what the status of this pull request is. It would be nice to get the arch/ changes into v3.17 but we are getting closer to v3.16-rc6 and I need to have things queued up before then.

I have also CCed Olof and the ARM SoC team (via arm at kernel.org) as if Daniel does provide a stable branch that includes this pull request and I use it as the basis for a branch with the arch changes then the ARM SoC people would like to know about it before I send a pull request for the arch/ changes.

From my point of view everything is ready for v3.17. Daniel, if you haven't

Quoted 1 line

Quoted 1 line

The following changes since commit

Quoted 39 lines

Quoted 39 lines

Linux 3.16-rc3 (2014-06-29 14:11:36 -0700)

are available in the git repository at:
git://linuxtv.org/pinchartl/fbdev.git timers/upstream/drivers

for you to fetch changes up to cca8d0596c4c7acb371ea1bc5eee9b404b30516a:
clocksource: sh_mtu2: Add DT support (2014-07-04 15:50:29 +0200)

----------------------------------------------------------------

Laurent Pinchart (10):
clocksource: sh_cmt: Drop support for legacy platform data
clocksource: sh_cmt: Replace global spinlock with a per-device
spinlock
clocksource: sh_tmu: Drop support for legacy platform data
clocksource: sh_tmu: Replace global spinlock with a per-device
spinlock
clocksource: sh_mtu2: Drop support for legacy platform data
clocksource: sh_mtu2: Replace global spinlock with a per-device
spinlock
clocksource: shmobile: Remove unused sh_timer_config members
clocksource: sh_cmt: Add DT support
clocksource: sh_tmu: Add DT support
clocksource: sh_mtu2: Add DT support

 Documentation/devicetree/bindings/timer/renesas,cmt.txt |  47 +++++
 .../devicetree/bindings/timer/renesas,mtu2.txt          |  39 ++++
 Documentation/devicetree/bindings/timer/renesas,tmu.txt |  39 ++++
 drivers/clocksource/sh_cmt.c                            | 233 +++++----
 drivers/clocksource/sh_mtu2.c                           | 146 ++++-----
 drivers/clocksource/sh_tmu.c                            | 127 +++++----
 include/linux/sh_timer.h                                |   5 -
 7 files changed, 309 insertions(+), 327 deletions(-)
 create mode 100644
 Documentation/devicetree/bindings/timer/renesas,cmt.txt
 create mode 100644
 Documentation/devicetree/bindings/timer/renesas,mtu2.txt
 create mode 100644

Documentation/devicetree/bindings/timer/renesas,tmu.txt

Hi Simon and Daniel,

Quoted 23 lines · On Sunday 13 July 2014 11:55:01 Simon Horman wrote:

[Cc Olof Johansson, ARM SoC Team]

Quoted 7 lines · Laurent Pinchart

Quoted 6 lines · On Friday 04 July 2014 15:53:32 Laurent Pinchart wrote:

Hi Daniel,

Could you please pull the following changes and drop the first version of this pull request ? I've fixed one last typo noticed by Simon in patch 09/19.

Quoted 6 lines

Quoted 3 lines

As last time I have board and SoC changes that depend on the driver changes and that will need to go through Simon's tree. Could you thus please provide a stable branch based on one of the v3.16-rc tags ?

Given that I'd like to get the arch/ part of the change set in v3.17, could I ask you to fast track this pull request if possible ?

Hi Laurent, Hi Daniel,

I am wondering what the status of this pull request is. It would be nice to get the arch/ changes into v3.17 but we are getting closer to v3.16-rc6 and I need to have things queued up before then.

Quoted 5 lines

I have also CCed Olof and the ARM SoC team (via arm at kernel.org) as if Daniel does provide a stable branch that includes this pull request and I use it as the basis for a branch with the arch changes then the ARM SoC people would like to know about it before I send a pull request for the arch/ changes.

From my point of view everything is ready for v3.17. Daniel, if you haven't
been abducted by aliens, could you please process the pull request ? If you have, let us know what we can do to help negotiate your release.

Quoted 1 line

Quoted 1 line

Quoted 1 line

The following changes since commit

4c834452aad01531db949414f94f817a86348d59:

Quoted 39 lines

Quoted 39 lines

Quoted 39 lines

   Linux 3.16-rc3 (2014-06-29 14:11:36 -0700)

are available in the git repository at:
git://linuxtv.org/pinchartl/fbdev.git timers/upstream/drivers

for you to fetch changes up to cca8d0596c4c7acb371ea1bc5eee9b404b30516a:

   clocksource: sh_mtu2: Add DT support (2014-07-04 15:50:29 +0200)

----------------------------------------------------------------

Laurent Pinchart (10):
clocksource: sh_cmt: Drop support for legacy platform data
clocksource: sh_cmt: Replace global spinlock with a per-device
spinlock
clocksource: sh_tmu: Drop support for legacy platform data
clocksource: sh_tmu: Replace global spinlock with a per-device
spinlock
clocksource: sh_mtu2: Drop support for legacy platform data
clocksource: sh_mtu2: Replace global spinlock with a per-device
spinlock
clocksource: shmobile: Remove unused sh_timer_config members
clocksource: sh_cmt: Add DT support
clocksource: sh_tmu: Add DT support
clocksource: sh_mtu2: Add DT support

  Documentation/devicetree/bindings/timer/renesas,cmt.txt |  47 +++++
  .../devicetree/bindings/timer/renesas,mtu2.txt          |  39 ++++
  Documentation/devicetree/bindings/timer/renesas,tmu.txt |  39 ++++
  drivers/clocksource/sh_cmt.c                            | 233 +++++----
  drivers/clocksource/sh_mtu2.c                           | 146 ++++-----
  drivers/clocksource/sh_tmu.c                            | 127 +++++----
  include/linux/sh_timer.h                                |   5 -
  7 files changed, 309 insertions(+), 327 deletions(-)

create mode 100644 Documentation/devicetree/bindings/timer/renesas,cmt.txt create mode 100644 Documentation/devicetree/bindings/timer/renesas,mtu2.txt create mode 100644 Documentation/devicetree/bindings/timer/renesas,tmu.txt

Quoted 32 lines · Laurent Pinchart

Hi Simon and Daniel,

Quoted 23 lines · On Sunday 13 July 2014 11:55:01 Simon Horman wrote:

[Cc Olof Johansson, ARM SoC Team]

Quoted 7 lines · Laurent Pinchart

Quoted 6 lines · On Friday 04 July 2014 15:53:32 Laurent Pinchart wrote:

Hi Daniel,

Could you please pull the following changes and drop the first version of this pull request ? I've fixed one last typo noticed by Simon in patch 09/19.

Quoted 6 lines

Quoted 3 lines

As last time I have board and SoC changes that depend on the driver changes and that will need to go through Simon's tree. Could you thus please provide a stable branch based on one of the v3.16-rc tags ?

Given that I'd like to get the arch/ part of the change set in v3.17, could I ask you to fast track this pull request if possible ?

Hi Laurent, Hi Daniel,

I am wondering what the status of this pull request is. It would be nice to get the arch/ changes into v3.17 but we are getting closer to v3.16-rc6 and I need to have things queued up before then.

Quoted 5 lines

I have also CCed Olof and the ARM SoC team (via arm at kernel.org) as if Daniel does provide a stable branch that includes this pull request and I use it as the basis for a branch with the arch changes then the ARM SoC people would like to know about it before I send a pull request for the arch/ changes.

Quoted 3 lines

From my point of view everything is ready for v3.17. Daniel, if you haven't been abducted by aliens, could you please process the pull request ? If you have, let us know what we can do to help negotiate your release.

Hi Laurent,

sorry for no giving some news. I am in vacation for these two weeks.

I will take care of the PR this evening or tomorrow evening and keep you in touch rapidly.

-- Daniel

Quoted 42 lines

Quoted 1 line

Quoted 1 line

Quoted 1 line

The following changes since commit

4c834452aad01531db949414f94f817a86348d59:

Quoted 39 lines

Quoted 39 lines

Quoted 39 lines

Linux 3.16-rc3 (2014-06-29 14:11:36 -0700)

are available in the git repository at:
git://linuxtv.org/pinchartl/fbdev.git timers/upstream/drivers

for you to fetch changes up to cca8d0596c4c7acb371ea1bc5eee9b404b30516a:
clocksource: sh_mtu2: Add DT support (2014-07-04 15:50:29 +0200)

----------------------------------------------------------------

Laurent Pinchart (10):
clocksource: sh_cmt: Drop support for legacy platform data
clocksource: sh_cmt: Replace global spinlock with a per-device
spinlock
clocksource: sh_tmu: Drop support for legacy platform data
clocksource: sh_tmu: Replace global spinlock with a per-device
spinlock
clocksource: sh_mtu2: Drop support for legacy platform data
clocksource: sh_mtu2: Replace global spinlock with a per-device
spinlock
clocksource: shmobile: Remove unused sh_timer_config members
clocksource: sh_cmt: Add DT support
clocksource: sh_tmu: Add DT support
clocksource: sh_mtu2: Add DT support

 Documentation/devicetree/bindings/timer/renesas,cmt.txt |  47 +++++
 .../devicetree/bindings/timer/renesas,mtu2.txt          |  39 ++++
 Documentation/devicetree/bindings/timer/renesas,tmu.txt |  39 ++++
 drivers/clocksource/sh_cmt.c                            | 233 +++++----
 drivers/clocksource/sh_mtu2.c                           | 146 ++++-----
 drivers/clocksource/sh_tmu.c                            | 127 +++++----
 include/linux/sh_timer.h                                |   5 -
 7 files changed, 309 insertions(+), 327 deletions(-)
 create mode 100644
 Documentation/devicetree/bindings/timer/renesas,cmt.txt
 create mode 100644
 Documentation/devicetree/bindings/timer/renesas,mtu2.txt
 create mode 100644

Documentation/devicetree/bindings/timer/renesas,tmu.txt

Signature · 10 lines

 <http://www.linaro.org/> Linaro.org ? Open source software for ARM SoCs

Follow Linaro:  <http://www.facebook.com/pages/Linaro> Facebook |
<http://twitter.com/#!/linaroorg> Twitter |
<http://www.linaro.org/linaro-blog/> Blog

--
To unsubscribe from this list: send the line "unsubscribe linux-sh" in
the body of a message to majordomo at vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Quoted 41 lines · Daniel Lezcano

Quoted 32 lines · Laurent Pinchart

Hi Simon and Daniel,

Quoted 23 lines · On Sunday 13 July 2014 11:55:01 Simon Horman wrote:

[Cc Olof Johansson, ARM SoC Team]

Quoted 7 lines · Laurent Pinchart

Quoted 6 lines · On Friday 04 July 2014 15:53:32 Laurent Pinchart wrote:

Hi Daniel,

Could you please pull the following changes and drop the first version of this pull request ? I've fixed one last typo noticed by Simon in patch 09/19.

Quoted 6 lines

Quoted 3 lines

As last time I have board and SoC changes that depend on the driver changes and that will need to go through Simon's tree. Could you thus please provide a stable branch based on one of the v3.16-rc tags ?

Given that I'd like to get the arch/ part of the change set in v3.17, could I ask you to fast track this pull request if possible ?

Hi Laurent, Hi Daniel,

I am wondering what the status of this pull request is. It would be nice to get the arch/ changes into v3.17 but we are getting closer to v3.16-rc6 and I need to have things queued up before then.

Quoted 5 lines

I have also CCed Olof and the ARM SoC team (via arm at kernel.org) as if Daniel does provide a stable branch that includes this pull request and I use it as the basis for a branch with the arch changes then the ARM SoC people would like to know about it before I send a pull request for the arch/ changes.

Quoted 3 lines

From my point of view everything is ready for v3.17. Daniel, if you haven't
been abducted by aliens, could you please process the pull request ? If you have, let us know what we can do to help negotiate your release.

Hi Laurent,

sorry for no giving some news. I am in vacation for these two weeks.

Quoted 2 lines

I will take care of the PR this evening or tomorrow evening and keep you in touch rapidly.

Hi Daniel,

thanks in advance. If you could create a stable branch for me to use as a base for the arch/ patches that would be great.

Quoted 60 lines

-- Daniel

Quoted 42 lines

Quoted 1 line

Quoted 1 line

Quoted 1 line

The following changes since commit

4c834452aad01531db949414f94f817a86348d59:

Quoted 39 lines

Quoted 39 lines

Quoted 39 lines

   Linux 3.16-rc3 (2014-06-29 14:11:36 -0700)

are available in the git repository at:
git://linuxtv.org/pinchartl/fbdev.git timers/upstream/drivers

for you to fetch changes up to cca8d0596c4c7acb371ea1bc5eee9b404b30516a:

   clocksource: sh_mtu2: Add DT support (2014-07-04 15:50:29 +0200)

----------------------------------------------------------------

Laurent Pinchart (10):
clocksource: sh_cmt: Drop support for legacy platform data
clocksource: sh_cmt: Replace global spinlock with a per-device
spinlock
clocksource: sh_tmu: Drop support for legacy platform data
clocksource: sh_tmu: Replace global spinlock with a per-device
spinlock
clocksource: sh_mtu2: Drop support for legacy platform data
clocksource: sh_mtu2: Replace global spinlock with a per-device
spinlock
clocksource: shmobile: Remove unused sh_timer_config members
clocksource: sh_cmt: Add DT support
clocksource: sh_tmu: Add DT support
clocksource: sh_mtu2: Add DT support

  Documentation/devicetree/bindings/timer/renesas,cmt.txt |  47 +++++
  .../devicetree/bindings/timer/renesas,mtu2.txt          |  39 ++++
  Documentation/devicetree/bindings/timer/renesas,tmu.txt |  39 ++++
  drivers/clocksource/sh_cmt.c                            | 233 +++++----
  drivers/clocksource/sh_mtu2.c                           | 146 ++++-----
  drivers/clocksource/sh_tmu.c                            | 127 +++++----
  include/linux/sh_timer.h                                |   5 -
  7 files changed, 309 insertions(+), 327 deletions(-)

create mode 100644 Documentation/devicetree/bindings/timer/renesas,cmt.txt create mode 100644 Documentation/devicetree/bindings/timer/renesas,mtu2.txt create mode 100644 Documentation/devicetree/bindings/timer/renesas,tmu.txt

--
<http://www.linaro.org/> Linaro.org ? Open source software for ARM SoCs

Follow Linaro: <http://www.facebook.com/pages/Linaro> Facebook |
<http://twitter.com/#!/linaroorg> Twitter |
<http://www.linaro.org/linaro-blog/> Blog

--
To unsubscribe from this list: send the line "unsubscribe linux-sh" in the body of a message to majordomo at vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html

Quoted 42 lines · Simon Horman

Quoted 41 lines · Daniel Lezcano

Quoted 32 lines · Laurent Pinchart

Hi Simon and Daniel,

Quoted 23 lines · On Sunday 13 July 2014 11:55:01 Simon Horman wrote:

[Cc Olof Johansson, ARM SoC Team]

Quoted 7 lines · Laurent Pinchart

Quoted 6 lines · On Friday 04 July 2014 15:53:32 Laurent Pinchart wrote:

Hi Daniel,

Could you please pull the following changes and drop the first version of this pull request ? I've fixed one last typo noticed by Simon in patch 09/19.

Quoted 6 lines

Quoted 3 lines

As last time I have board and SoC changes that depend on the driver changes and that will need to go through Simon's tree. Could you thus please provide a stable branch based on one of the v3.16-rc tags ?

Given that I'd like to get the arch/ part of the change set in v3.17, could I ask you to fast track this pull request if possible ?

Hi Laurent, Hi Daniel,

I am wondering what the status of this pull request is. It would be nice to get the arch/ changes into v3.17 but we are getting closer to v3.16-rc6 and I need to have things queued up before then.

Quoted 5 lines

I have also CCed Olof and the ARM SoC team (via arm at kernel.org) as if Daniel does provide a stable branch that includes this pull request and I use it as the basis for a branch with the arch changes then the ARM SoC people would like to know about it before I send a pull request for the arch/ changes.

Quoted 3 lines

From my point of view everything is ready for v3.17. Daniel, if you haven't been abducted by aliens, could you please process the pull request ? If you have, let us know what we can do to help negotiate your release.

Hi Laurent,

sorry for no giving some news. I am in vacation for these two weeks.

Quoted 7 lines

Quoted 2 lines

I will take care of the PR this evening or tomorrow evening and keep you in touch rapidly.

Hi Daniel,

thanks in advance. If you could create a stable branch for me to use as a base for the arch/ patches that would be great.

Hi Simon and Laurent,

I pulled in the following branch:

git://git.linaro.org/people/daniel.lezcano/linux.git
clockevents/renesas-timers-dt

I will keep this branch untouched and it will be merge in the 3.17 branch.

Quoted 30 lines · Laurent Pinchart

Quoted 23 lines · On Sunday 13 July 2014 11:55:01 Simon Horman wrote:

[Cc Olof Johansson, ARM SoC Team]

Quoted 7 lines · Laurent Pinchart

Quoted 6 lines · On Friday 04 July 2014 15:53:32 Laurent Pinchart wrote:

Hi Daniel,

Could you please pull the following changes and drop the first version of this pull request ? I've fixed one last typo noticed by Simon in patch 09/19.

Quoted 6 lines

Quoted 3 lines

As last time I have board and SoC changes that depend on the driver changes and that will need to go through Simon's tree. Could you thus please provide a stable branch based on one of the v3.16-rc tags ?

Given that I'd like to get the arch/ part of the change set in v3.17, could I ask you to fast track this pull request if possible ?

Hi Laurent, Hi Daniel,

I am wondering what the status of this pull request is. It would be nice to get the arch/ changes into v3.17 but we are getting closer to v3.16-rc6 and I need to have things queued up before then.

Quoted 6 lines

I have also CCed Olof and the ARM SoC team (via arm at kernel.org) as if Daniel does provide a stable branch that includes this pull request and I use it as the basis for a branch with the arch changes then the ARM SoC people would like to know about it before I send a pull request for the arch/ changes.

Quoted 3 lines

From my point of view everything is ready for v3.17. Daniel, if you haven't been abducted by aliens, could you please process the pull request ? If you have, let us know what we can do to help negotiate your release.

Hi Laurent,

sorry for no giving some news. I am in vacation for these two weeks.

I will take care of the PR this evening or tomorrow evening and keep you in touch rapidly.

Quoted 9 lines

Quoted 1 line

Quoted 1 line

Quoted 1 line

The following changes since commit

4c834452aad01531db949414f94f817a86348d59:

Quoted 6 lines

Quoted 6 lines

Quoted 6 lines

   Linux 3.16-rc3 (2014-06-29 14:11:36 -0700)

are available in the git repository at:
git://linuxtv.org/pinchartl/fbdev.git timers/upstream/drivers

for you to fetch changes up to

Quoted 33 lines

Quoted 33 lines

Quoted 33 lines

Quoted 33 lines

   clocksource: sh_mtu2: Add DT support (2014-07-04 15:50:29 +0200)

----------------------------------------------------------------

Laurent Pinchart (10):
clocksource: sh_cmt: Drop support for legacy platform data
clocksource: sh_cmt: Replace global spinlock with a per-device
spinlock
clocksource: sh_tmu: Drop support for legacy platform data
clocksource: sh_tmu: Replace global spinlock with a per-device
spinlock
clocksource: sh_mtu2: Drop support for legacy platform data
clocksource: sh_mtu2: Replace global spinlock with a per-device
spinlock
clocksource: shmobile: Remove unused sh_timer_config members
clocksource: sh_cmt: Add DT support
clocksource: sh_tmu: Add DT support
clocksource: sh_mtu2: Add DT support

Documentation/devicetree/bindings/timer/renesas,cmt.txt |  47 +++++
.../devicetree/bindings/timer/renesas,mtu2.txt          |  39 ++++
Documentation/devicetree/bindings/timer/renesas,tmu.txt |  39 ++++
drivers/clocksource/sh_cmt.c                            | 233 ++++---
drivers/clocksource/sh_mtu2.c                           | 146 +++----
drivers/clocksource/sh_tmu.c                            | 127 ++++---
include/linux/sh_timer.h                                |   5 -
7 files changed, 309 insertions(+), 327 deletions(-)

create mode 100644 Documentation/devicetree/bindings/timer/renesas,cmt.txt create mode 100644 Documentation/devicetree/bindings/timer/renesas,mtu2.txt create mode 100644 Documentation/devicetree/bindings/timer/renesas,tmu.txt

Hi Daniel,

Quoted 37 lines · On Sunday 13 July 2014 16:42:09 Daniel Lezcano wrote:

Quoted 30 lines · Laurent Pinchart

Quoted 23 lines · On Sunday 13 July 2014 11:55:01 Simon Horman wrote:

[Cc Olof Johansson, ARM SoC Team]

Quoted 7 lines · Laurent Pinchart

Quoted 6 lines · On Friday 04 July 2014 15:53:32 Laurent Pinchart wrote:

Hi Daniel,

Could you please pull the following changes and drop the first version of this pull request ? I've fixed one last typo noticed by Simon in patch 09/19.

Quoted 6 lines

Quoted 3 lines

As last time I have board and SoC changes that depend on the driver changes and that will need to go through Simon's tree. Could you thus please provide a stable branch based on one of the v3.16-rc tags ?

Given that I'd like to get the arch/ part of the change set in v3.17, could I ask you to fast track this pull request if possible ?

Hi Laurent, Hi Daniel,

I am wondering what the status of this pull request is. It would be nice to get the arch/ changes into v3.17 but we are getting closer to v3.16-rc6 and I need to have things queued up before then.

Quoted 6 lines

I have also CCed Olof and the ARM SoC team (via arm at kernel.org) as if Daniel does provide a stable branch that includes this pull request and I use it as the basis for a branch with the arch changes then the ARM SoC people would like to know about it before I send a pull request for the arch/ changes.

Quoted 3 lines

From my point of view everything is ready for v3.17. Daniel, if you
haven't been abducted by aliens, could you please process the pull request ? If you have, let us know what we can do to help negotiate your release.

Hi Laurent,

Quoted 4 lines

sorry for no giving some news. I am in vacation for these two weeks.

I will take care of the PR this evening or tomorrow evening and keep you in touch rapidly.

Thank you, and sorry for disturbing you during your holidays. Next time if you setup an automatic e-mail reply I'll be more patient and won't worry about aliens :-)

Quoted 9 lines

Quoted 9 lines

Quoted 1 line

Quoted 1 line

Quoted 1 line

The following changes since commit

4c834452aad01531db949414f94f817a86348d59:

Quoted 6 lines

Quoted 6 lines

Quoted 6 lines

    Linux 3.16-rc3 (2014-06-29 14:11:36 -0700)

are available in the git repository at:
git://linuxtv.org/pinchartl/fbdev.git timers/upstream/drivers

for you to fetch changes up to

cca8d0596c4c7acb371ea1bc5eee9b404b30516a:

Quoted 33 lines

Quoted 33 lines

Quoted 33 lines

Quoted 33 lines

Quoted 33 lines

    clocksource: sh_mtu2: Add DT support (2014-07-04 15:50:29 +0200)

----------------------------------------------------------------

Laurent Pinchart (10):
clocksource: sh_cmt: Drop support for legacy platform data
clocksource: sh_cmt: Replace global spinlock with a per-device
spinlock
clocksource: sh_tmu: Drop support for legacy platform data
clocksource: sh_tmu: Replace global spinlock with a per-device
spinlock
clocksource: sh_mtu2: Drop support for legacy platform data
clocksource: sh_mtu2: Replace global spinlock with a per-device
spinlock
clocksource: shmobile: Remove unused sh_timer_config members
clocksource: sh_cmt: Add DT support
clocksource: sh_tmu: Add DT support
clocksource: sh_mtu2: Add DT support

Documentation/devicetree/bindings/timer/renesas,cmt.txt |  47 +++++
.../devicetree/bindings/timer/renesas,mtu2.txt          |  39 ++++
Documentation/devicetree/bindings/timer/renesas,tmu.txt |  39 ++++
drivers/clocksource/sh_cmt.c                            | 233 ++++---
drivers/clocksource/sh_mtu2.c                           | 146 +++----
drivers/clocksource/sh_tmu.c                            | 127 ++++---
include/linux/sh_timer.h                                |   5 -
7 files changed, 309 insertions(+), 327 deletions(-)

create mode 100644 Documentation/devicetree/bindings/timer/renesas,cmt.txt create mode 100644 Documentation/devicetree/bindings/timer/renesas,mtu2.txt create mode 100644 Documentation/devicetree/bindings/timer/renesas,tmu.txt