ARM: vf610: add FlexCAN support

PATCH Applied Stefan Agner 4 participants 27 messages Jul 15, 2014 – Aug 14, 2014

Subsystems (7)

Device tree bindings Arm (32-bit) Arm sub-architectures Arm i.MX and Layerscape +3 more subsystems

lore

Share & tools

lore

Stefan Agner

author reviewer

2014-07-15 12:56 UTC #0 lore raw

v3 cover ARM: vf610: add FlexCAN support

This series adds support for Vybrid (aka vf610) to the FlexCAN controller and extends the device tree accordingly.

Changes in v3:
- Return error number in flexcan_get_berr_counter if clock enabling fails
- Add the FLEXCANX_EN clocks as new clocks

Changes in v2:
- Split out patch (seperate dt, clocks and driver changes)
- Use spaces for hardware feature flags table
- Remove drive-by change of esdhc register length
- Added related fix which enables clock in berr_counter

Stefan Agner (4):
ARM: dts: vf610: add FlexCAN node
ARM: imx: clk-vf610: fix FlexCAN clock gating
can: flexcan: switch on clocks before accessing ecr register
can: flexcan: add vf610 support for FlexCAN

 arch/arm/boot/dts/vf610.dtsi            | 23 +++++++++
 arch/arm/mach-imx/clk-vf610.c           |  6 ++-
 drivers/net/can/flexcan.c               | 91 +++++++++++++++++++++++++++++----
 include/dt-bindings/clock/vf610-clock.h |  4 +-
 4 files changed, 110 insertions(+), 14 deletions(-)

Signature · 1 line

2.0.1

Stefan Agner

author reviewer

2014-07-15 12:56 UTC #1 lore raw

PATCH v3 1/4 ARM: dts: vf610: add FlexCAN node

Add FlexCAN node for the two FlexCAN IP instances in Vybrid.

Signed-off-by Stefan Agner <[email protected]>

---
 arch/arm/boot/dts/vf610.dtsi | 23 +++++++++++++++++++++++
 1 file changed, 23 insertions(+)

arch/arm/boot/dts/vf610.dtsi +23 -0

index 3fb127a..9404853 100644
@@ -14,6 +14,8 @@
 
 / {
 	aliases {
+		can0 = &can0;
+		can1 = &can1;
 		serial0 = &uart0;
 		serial1 = &uart1;
 		serial2 = &uart2;

@@ -103,6 +105,16 @@
 					<&clks VF610_CLK_DMAMUX1>;
 			};
 
+			can0: flexcan at 40020000 {
+				compatible = "fsl,vf610-flexcan";
+				reg = <0x40020000 0x4000>;
+				interrupts = <0 58 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clks VF610_CLK_FLEXCAN0>,
+					 <&clks VF610_CLK_FLEXCAN0>;
+				clock-names = "ipg", "per";
+				status = "disabled";
+			};
+
 			uart0: serial at 40027000 {
 				compatible = "fsl,vf610-lpuart";
 				reg = <0x40027000 0x1000>;

@@ -414,6 +426,17 @@
 				clock-names = "nfc";
 				status = "disabled";
 			};
+
+			can1: flexcan at 400d4000 {
+				compatible = "fsl,vf610-flexcan";
+				reg = <0x400d4000 0x4000>;
+				interrupts = <0 59 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clks VF610_CLK_FLEXCAN1>,
+					 <&clks VF610_CLK_FLEXCAN1>;
+				clock-names = "ipg", "per";
+				status = "disabled";
+			};
+
 		};
 	};
 };

Signature · 1 line

2.0.1

Stefan Agner

author reviewer

2014-07-15 12:56 UTC #2 lore raw

PATCH v3 2/4 ARM: imx: clk-vf610: fix FlexCAN clock gating

In reply to Stefan Agner

Extend the clock control for FlexCAN with the second gate which enable the clocks in the Clock Divider (CCM_CSCDR2) register too.

Signed-off-by Stefan Agner <[email protected]>

---
 arch/arm/mach-imx/clk-vf610.c           | 6 ++++--
 include/dt-bindings/clock/vf610-clock.h | 4 +++-
 2 files changed, 7 insertions(+), 3 deletions(-)

arch/arm/mach-imx/clk-vf610.c +4 -2

index 22dc3ee..f964079 100644
@@ -295,8 +295,10 @@ static void __init vf610_clocks_init(struct device_node *ccm_node)
 
 	clk[VF610_CLK_ASRC] = imx_clk_gate2("asrc", "ipg_bus", CCM_CCGR4, CCM_CCGRx_CGn(1));
 
-	clk[VF610_CLK_FLEXCAN0] = imx_clk_gate2("flexcan0", "ipg_bus", CCM_CCGR0, CCM_CCGRx_CGn(0));
-	clk[VF610_CLK_FLEXCAN1] = imx_clk_gate2("flexcan1", "ipg_bus", CCM_CCGR9, CCM_CCGRx_CGn(4));
+	clk[VF610_CLK_FLEXCAN0_EN] = imx_clk_gate("flexcan0_en", "ipg_bus", CCM_CSCDR2, 11);
+	clk[VF610_CLK_FLEXCAN0] = imx_clk_gate2("flexcan0", "flexcan0_en", CCM_CCGR0, CCM_CCGRx_CGn(0));
+	clk[VF610_CLK_FLEXCAN1_EN] = imx_clk_gate("flexcan1_en", "ipg_bus", CCM_CSCDR2, 12);
+	clk[VF610_CLK_FLEXCAN1] = imx_clk_gate2("flexcan1", "flexcan1_en", CCM_CCGR9, CCM_CCGRx_CGn(4));
 
 	clk[VF610_CLK_DMAMUX0] = imx_clk_gate2("dmamux0", "platform_bus", CCM_CCGR0, CCM_CCGRx_CGn(4));
 	clk[VF610_CLK_DMAMUX1] = imx_clk_gate2("dmamux1", "platform_bus", CCM_CCGR0, CCM_CCGRx_CGn(5));

include/dt-bindings/clock/vf610-clock.h +3 -1

index a916029..00953d9 100644
@@ -164,6 +164,8 @@
 #define VF610_CLK_DMAMUX1		151
 #define VF610_CLK_DMAMUX2		152
 #define VF610_CLK_DMAMUX3		153
-#define VF610_CLK_END			154
+#define VF610_CLK_FLEXCAN0_EN		154
+#define VF610_CLK_FLEXCAN1_EN		155
+#define VF610_CLK_END			156
 
 #endif /* __DT_BINDINGS_CLOCK_VF610_H */

Signature · 1 line

2.0.1

Stefan Agner

author reviewer

2014-07-15 12:56 UTC #3 lore raw

PATCH v3 3/4 can: flexcan: switch on clocks before accessing ecr register

In reply to Stefan Agner

Reported-by Ashutosh Singh <[email protected]>

[stefan at agner.ch: added return check for clk_enable_prepare]

Signed-off-by Stefan Agner <[email protected]>

---
 drivers/net/can/flexcan.c | 18 ++++++++++++++++--
 1 file changed, 16 insertions(+), 2 deletions(-)

drivers/net/can/flexcan.c +16 -2

index f425ec2..89745aa 100644
@@ -383,12 +383,26 @@ static int flexcan_get_berr_counter(const struct net_device *dev,
 {
 	const struct flexcan_priv *priv = netdev_priv(dev);
 	struct flexcan_regs __iomem *regs = priv->base;
-	u32 reg = flexcan_read(&regs->ecr);
+	u32 reg, err;
+
+	err = clk_prepare_enable(priv->clk_ipg);
+	if (err)
+		return err;
+
+	err = clk_prepare_enable(priv->clk_per);
+	if (err)
+		goto out_disable_ipg;
+
+	reg = flexcan_read(&regs->ecr);
 
 	bec->txerr = (reg >> 0) & 0xff;
 	bec->rxerr = (reg >> 8) & 0xff;
 
-	return 0;
+	clk_disable_unprepare(priv->clk_per);
+ out_disable_ipg:
+	clk_disable_unprepare(priv->clk_ipg);
+
+	return err;
 }
 
 static int flexcan_start_xmit(struct sk_buff *skb, struct net_device *dev)

Signature · 1 line

2.0.1

Lothar Waßmann

2014-07-15 13:54 UTC #4 lore raw

Re: [PATCH v3 3/4] can: flexcan: switch on clocks before accessing ecr register

Hi,

Quoted 20 lines · Stefan Agner

Reported-by Ashutosh Singh <[email protected]>
Suggested-by Marc Kleine-Budde <[email protected]>
[stefan at agner.ch: added return check for clk_enable_prepare]
Signed-off-by Stefan Agner <[email protected]>
---
 drivers/net/can/flexcan.c | 18 ++++++++++++++++--
 1 file changed, 16 insertions(+), 2 deletions(-)
drivers/net/can/flexcan.c +2 -1
index f425ec2..89745aa 100644
@@ -383,12 +383,26 @@ static int flexcan_get_berr_counter(const struct net_device *dev,
 {
 	const struct flexcan_priv *priv = netdev_priv(dev);
 	struct flexcan_regs __iomem *regs = priv->base;
-	u32 reg = flexcan_read(&regs->ecr);
+	u32 reg, err;
+

drivers/net/can/flexcan.c static int flexcan_get_berr_counter(const struct net_device *dev, · line 397

Quoted 10 lines

drivers/net/can/flexcan.c +9 -0

+	err = clk_prepare_enable(priv->clk_ipg);
+	if (err)
+		return err;
+
+	err = clk_prepare_enable(priv->clk_per);
+	if (err)
+		goto out_disable_ipg;
+
+	reg = flexcan_read(&regs->ecr);

flexcan_get_berr_counter() may be called from interrupt context and thus must not call any functions that can sleep.
Compiling the driver with CONFIG_DEBUG_ATOMIC_SLEEP would catch this!

Lothar Wa?mann

Signature · 9 lines

___________________________________________________________

Ka-Ro electronics GmbH | Pascalstra?e 22 | D - 52076 Aachen
Phone: +49 2408 1402-0 | Fax: +49 2408 1402-10
Gesch?ftsf?hrer: Matthias Kaussen
Handelsregistereintrag: Amtsgericht Aachen, HRB 4996

www.karo-electronics.de | info at karo-electronics.de
___________________________________________________________

Marc Kleine-Budde

maintainer

2014-07-15 13:57 UTC #5 lore raw

Re: [PATCH v3 3/4] can: flexcan: switch on clocks before accessing ecr register

Quoted 28 lines · Lothar Wa?mann

Hi,
Quoted 25 lines · Stefan Agner
Reported-by Ashutosh Singh <[email protected]>
Suggested-by Marc Kleine-Budde <[email protected]>
[stefan at agner.ch: added return check for clk_enable_prepare]
Signed-off-by Stefan Agner <[email protected]>
---
 drivers/net/can/flexcan.c | 18 ++++++++++++++++--
 1 file changed, 16 insertions(+), 2 deletions(-)
drivers/net/can/flexcan.c +7 -1
index f425ec2..89745aa 100644
@@ -383,12 +383,26 @@ static int flexcan_get_berr_counter(const struct net_device *dev,
 {
 	const struct flexcan_priv *priv = netdev_priv(dev);
 	struct flexcan_regs __iomem *regs = priv->base;
-	u32 reg = flexcan_read(&regs->ecr);
+	u32 reg, err;
+
+	err = clk_prepare_enable(priv->clk_ipg);
+	if (err)
+		return err;
+
+	err = clk_prepare_enable(priv->clk_per);

Quoted 8 lines

drivers/net/can/flexcan.c static int flexcan_get_berr_counter(const struct net_device *dev, · line 397
Quoted 5 lines
drivers/net/can/flexcan.c +4 -0
+	if (err)
+		goto out_disable_ipg;
+
+	reg = flexcan_read(&regs->ecr);
 
flexcan_get_berr_counter() may be called from interrupt context and thus must not call any functions that can sleep.
Compiling the driver with CONFIG_DEBUG_ATOMIC_SLEEP would catch this!

It's called from the NAPI softirq. I'll prepare a patch.

Marc

Signature · 12 lines

Pengutronix e.K.                  | Marc Kleine-Budde           |
Industrial Linux Solutions        | Phone: +49-231-2826-924     |
Vertretung West/Dortmund          | Fax:   +49-5121-206917-5555 |
Amtsgericht Hildesheim, HRA 2686  | http://www.pengutronix.de   |

-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 242 bytes
Desc: OpenPGP digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20140715/00bbeec8/attachment-0001.sig>

Stefan Agner

author reviewer

2014-07-15 12:56 UTC #6 lore raw

PATCH v3 4/4 can: flexcan: add vf610 support for FlexCAN

In reply to Stefan Agner

Extend FlexCAN driver to support Vybrid. Vybrids variant of the IP has ECC support which is controlled through the memory error control register (MECR). There is also an errata which leads to false positive error detections (ID e5295). This patch disables the memory error detection completely.

Signed-off-by Stefan Agner <[email protected]>

---
 drivers/net/can/flexcan.c | 73 +++++++++++++++++++++++++++++++++++++++++------
 1 file changed, 64 insertions(+), 9 deletions(-)

drivers/net/can/flexcan.c +64 -9

index 89745aa..1c31a5d 100644
@@ -92,6 +92,27 @@
 #define FLEXCAN_CTRL_ERR_ALL \
 	(FLEXCAN_CTRL_ERR_BUS | FLEXCAN_CTRL_ERR_STATE)
 
+/* FLEXCAN control register 2 (CTRL2) bits */
+#define FLEXCAN_CRL2_ECRWRE		BIT(29)
+#define FLEXCAN_CRL2_WRMFRZ		BIT(28)
+#define FLEXCAN_CRL2_RFFN(x)		(((x) & 0x0f) << 24)
+#define FLEXCAN_CRL2_TASD(x)		(((x) & 0x1f) << 19)
+#define FLEXCAN_CRL2_MRP		BIT(18)
+#define FLEXCAN_CRL2_RRS		BIT(17)
+#define FLEXCAN_CRL2_EACEN		BIT(16)
+
+/* FLEXCAN memory error control register (MECR) bits */
+#define FLEXCAN_MECR_ECRWRDIS		BIT(31)
+#define FLEXCAN_MECR_HANCEI_MSK		BIT(19)
+#define FLEXCAN_MECR_FANCEI_MSK		BIT(18)
+#define FLEXCAN_MECR_CEI_MSK		BIT(16)
+#define FLEXCAN_MECR_HAERRIE		BIT(15)
+#define FLEXCAN_MECR_FAERRIE		BIT(14)
+#define FLEXCAN_MECR_EXTERRIE		BIT(13)
+#define FLEXCAN_MECR_RERRDIS		BIT(9)
+#define FLEXCAN_MECR_ECCDIS		BIT(8)
+#define FLEXCAN_MECR_NCEFAFRZ		BIT(7)
+
 /* FLEXCAN error and status register (ESR) bits */
 #define FLEXCAN_ESR_TWRN_INT		BIT(17)
 #define FLEXCAN_ESR_RWRN_INT		BIT(16)

@@ -150,18 +171,20 @@
  * FLEXCAN hardware feature flags
  *
  * Below is some version info we got:
- *    SOC   Version   IP-Version  Glitch-  [TR]WRN_INT
- *                                Filter?   connected?
- *   MX25  FlexCAN2  03.00.00.00     no         no
- *   MX28  FlexCAN2  03.00.04.00    yes        yes
- *   MX35  FlexCAN2  03.00.00.00     no         no
- *   MX53  FlexCAN2  03.00.00.00    yes         no
- *   MX6s  FlexCAN3  10.00.12.00    yes        yes
+ *    SOC   Version   IP-Version  Glitch-  [TR]WRN_INT  Memory err
+ *                                Filter?   connected?  detection
+ *   MX25  FlexCAN2  03.00.00.00     no         no         no
+ *   MX28  FlexCAN2  03.00.04.00    yes        yes         no
+ *   MX35  FlexCAN2  03.00.00.00     no         no         no
+ *   MX53  FlexCAN2  03.00.00.00    yes         no         no
+ *   MX6s  FlexCAN3  10.00.12.00    yes        yes         no
+ *   VF610 FlexCAN3  ?               no         no        yes
  *
  * Some SOCs do not have the RX_WARN & TX_WARN interrupt line connected.
  */
 #define FLEXCAN_HAS_V10_FEATURES	BIT(1) /* For core version >= 10 */
 #define FLEXCAN_HAS_BROKEN_ERR_STATE	BIT(2) /* [TR]WRN_INT not connected */
+#define FLEXCAN_HAS_MECR_FEATURES	BIT(3) /* Memory error detection */
 
 /* Structure of the message buffer */
 struct flexcan_mb {

@@ -192,8 +215,11 @@ struct flexcan_regs {
 	u32 crcr;		/* 0x44 */
 	u32 rxfgmask;		/* 0x48 */
 	u32 rxfir;		/* 0x4c */
-	u32 _reserved3[12];
+	u32 _reserved3[12];	/* 0x50 */
 	struct flexcan_mb cantxfg[64];
+	u32 _reserved4[408];
+	u32 mecr;		/* 0xae0 */
+	u32 erriar;		/* 0xae4 */
 };
 
 struct flexcan_devtype_data {

@@ -223,6 +249,9 @@ static struct flexcan_devtype_data fsl_imx28_devtype_data;
 static struct flexcan_devtype_data fsl_imx6q_devtype_data = {
 	.features = FLEXCAN_HAS_V10_FEATURES,
 };
+static struct flexcan_devtype_data fsl_vf610_devtype_data = {
+	.features = FLEXCAN_HAS_V10_FEATURES | FLEXCAN_HAS_MECR_FEATURES,
+};
 
 static const struct can_bittiming_const flexcan_bittiming_const = {
 	.name = DRV_NAME,

@@ -807,7 +836,7 @@ static int flexcan_chip_start(struct net_device *dev)
 	struct flexcan_priv *priv = netdev_priv(dev);
 	struct flexcan_regs __iomem *regs = priv->base;
 	int err;
-	u32 reg_mcr, reg_ctrl;
+	u32 reg_mcr, reg_ctrl, reg_crl2, reg_mecr;
 
 	/* enable module */
 	err = flexcan_chip_enable(priv);

@@ -884,6 +913,31 @@ static int flexcan_chip_start(struct net_device *dev)
 	if (priv->devtype_data->features & FLEXCAN_HAS_V10_FEATURES)
 		flexcan_write(0x0, &regs->rxfgmask);
 
+	/*
+	 * On Vybrid, disable memory error detection interrupts
+	 * and freeze mode.
+	 * This also works around errata e5295 which generates
+	 * false positive memory errors and put the device in
+	 * freeze mode.
+	 */
+	if (priv->devtype_data->features & FLEXCAN_HAS_MECR_FEATURES) {
+		/*
+		 * Follow the protocol as described in "Detection
+		 * and Correction of Memory Errors" to write to
+		 * MECR register
+		 */
+		reg_crl2 = flexcan_read(&regs->crl2);
+		reg_crl2 |= FLEXCAN_CRL2_ECRWRE;
+		flexcan_write(reg_crl2, &regs->crl2);
+
+		reg_mecr = flexcan_read(&regs->mecr);
+		reg_mecr &= ~FLEXCAN_MECR_ECRWRDIS;
+		flexcan_write(reg_mecr, &regs->mecr);
+		reg_mecr &= ~(FLEXCAN_MECR_NCEFAFRZ | FLEXCAN_MECR_HANCEI_MSK |
+				FLEXCAN_MECR_FANCEI_MSK);
+		flexcan_write(reg_mecr, &regs->mecr);
+	}
+
 	err = flexcan_transceiver_enable(priv);
 	if (err)
 		goto out_chip_disable;

@@ -1094,6 +1148,7 @@ static const struct of_device_id flexcan_of_match[] = {
 	{ .compatible = "fsl,imx6q-flexcan", .data = &fsl_imx6q_devtype_data, },
 	{ .compatible = "fsl,imx28-flexcan", .data = &fsl_imx28_devtype_data, },
 	{ .compatible = "fsl,p1010-flexcan", .data = &fsl_p1010_devtype_data, },
+	{ .compatible = "fsl,vf610-flexcan", .data = &fsl_vf610_devtype_data, },
 	{ /* sentinel */ },
 };
 MODULE_DEVICE_TABLE(of, flexcan_of_match);

Signature · 1 line

2.0.1

Marc Kleine-Budde

maintainer

2014-07-15 14:24 UTC #7 lore raw

Re: [PATCH v3 4/4] can: flexcan: add vf610 support for FlexCAN

Quoted 52 lines · Stefan Agner

Signed-off-by Stefan Agner <[email protected]>

---
 drivers/net/can/flexcan.c | 73 +++++++++++++++++++++++++++++++++++++++++------
 1 file changed, 64 insertions(+), 9 deletions(-)

drivers/net/can/flexcan.c +21 -5

index 89745aa..1c31a5d 100644
@@ -92,6 +92,27 @@
 #define FLEXCAN_CTRL_ERR_ALL \
 	(FLEXCAN_CTRL_ERR_BUS | FLEXCAN_CTRL_ERR_STATE)
 
+/* FLEXCAN control register 2 (CTRL2) bits */
+#define FLEXCAN_CRL2_ECRWRE		BIT(29)
+#define FLEXCAN_CRL2_WRMFRZ		BIT(28)
+#define FLEXCAN_CRL2_RFFN(x)		(((x) & 0x0f) << 24)
+#define FLEXCAN_CRL2_TASD(x)		(((x) & 0x1f) << 19)
+#define FLEXCAN_CRL2_MRP		BIT(18)
+#define FLEXCAN_CRL2_RRS		BIT(17)
+#define FLEXCAN_CRL2_EACEN		BIT(16)
+
+/* FLEXCAN memory error control register (MECR) bits */
+#define FLEXCAN_MECR_ECRWRDIS		BIT(31)
+#define FLEXCAN_MECR_HANCEI_MSK		BIT(19)
+#define FLEXCAN_MECR_FANCEI_MSK		BIT(18)
+#define FLEXCAN_MECR_CEI_MSK		BIT(16)
+#define FLEXCAN_MECR_HAERRIE		BIT(15)
+#define FLEXCAN_MECR_FAERRIE		BIT(14)
+#define FLEXCAN_MECR_EXTERRIE		BIT(13)
+#define FLEXCAN_MECR_RERRDIS		BIT(9)
+#define FLEXCAN_MECR_ECCDIS		BIT(8)
+#define FLEXCAN_MECR_NCEFAFRZ		BIT(7)
+
 /* FLEXCAN error and status register (ESR) bits */
 #define FLEXCAN_ESR_TWRN_INT		BIT(17)
 #define FLEXCAN_ESR_RWRN_INT		BIT(16)

@@ -150,18 +171,20 @@
  * FLEXCAN hardware feature flags
  *
  * Below is some version info we got:
- *    SOC   Version   IP-Version  Glitch-  [TR]WRN_INT
- *                                Filter?   connected?
- *   MX25  FlexCAN2  03.00.00.00     no         no
- *   MX28  FlexCAN2  03.00.04.00    yes        yes
- *   MX35  FlexCAN2  03.00.00.00     no         no

drivers/net/can/flexcan.c line 181

Quoted 10 lines

drivers/net/can/flexcan.c +8 -2

- *   MX53  FlexCAN2  03.00.00.00    yes         no
- *   MX6s  FlexCAN3  10.00.12.00    yes        yes
+ *    SOC   Version   IP-Version  Glitch-  [TR]WRN_INT  Memory err
+ *                                Filter?   connected?  detection
+ *   MX25  FlexCAN2  03.00.00.00     no         no         no
+ *   MX28  FlexCAN2  03.00.04.00    yes        yes         no
+ *   MX35  FlexCAN2  03.00.00.00     no         no         no
+ *   MX53  FlexCAN2  03.00.00.00    yes         no         no
+ *   MX6s  FlexCAN3  10.00.12.00    yes        yes         no
+ *   VF610 FlexCAN3  ?               no         no        yes

                                        ^^         ^^

Can you check the datasheet if the flexcan core has a "Glitch Filter Width Register (FLEXCANx_GFWR)"

Can you check if the core generates a warning interrupt with the current setup, if you don't switch on bus error reporting? This means internally the [TR]WRN_INT is connected and works as specified.

Quoted 23 lines

drivers/net/can/flexcan.c +5 -1

  *
  * Some SOCs do not have the RX_WARN & TX_WARN interrupt line connected.
  */
 #define FLEXCAN_HAS_V10_FEATURES	BIT(1) /* For core version >= 10 */
 #define FLEXCAN_HAS_BROKEN_ERR_STATE	BIT(2) /* [TR]WRN_INT not connected */
+#define FLEXCAN_HAS_MECR_FEATURES	BIT(3) /* Memory error detection */
 
 /* Structure of the message buffer */
 struct flexcan_mb {

@@ -192,8 +215,11 @@ struct flexcan_regs {
 	u32 crcr;		/* 0x44 */
 	u32 rxfgmask;		/* 0x48 */
 	u32 rxfir;		/* 0x4c */
-	u32 _reserved3[12];
+	u32 _reserved3[12];	/* 0x50 */
 	struct flexcan_mb cantxfg[64];
+	u32 _reserved4[408];
+	u32 mecr;		/* 0xae0 */
+	u32 erriar;		/* 0xae4 */
 };
 
 struct flexcan_devtype_data {

drivers/net/can/flexcan.c static struct flexcan_devtype_data fsl_imx28_devtype_data; · line 254

Quoted 6 lines

drivers/net/can/flexcan.c +3 -0

@@ -223,6 +249,9 @@ static struct flexcan_devtype_data fsl_imx28_devtype_data;
 static struct flexcan_devtype_data fsl_imx6q_devtype_data = {
 	.features = FLEXCAN_HAS_V10_FEATURES,
 };
+static struct flexcan_devtype_data fsl_vf610_devtype_data = {
+	.features = FLEXCAN_HAS_V10_FEATURES | FLEXCAN_HAS_MECR_FEATURES,
+};

Marc

Signature · 12 lines

Pengutronix e.K.                  | Marc Kleine-Budde           |
Industrial Linux Solutions        | Phone: +49-231-2826-924     |
Vertretung West/Dortmund          | Fax:   +49-5121-206917-5555 |
Amtsgericht Hildesheim, HRA 2686  | http://www.pengutronix.de   |

-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 242 bytes
Desc: OpenPGP digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20140715/c91045cb/attachment.sig>

Stefan Agner

author reviewer

2014-07-16 06:43 UTC #8 lore raw

Re: [PATCH v3 4/4] can: flexcan: add vf610 support for FlexCAN

Am 2014-07-15 16:24, schrieb Marc Kleine-Budde:
<snip>

Quoted 21 lines

Quoted 9 lines

drivers/net/can/flexcan.c +0 -5

@@ -150,18 +171,20 @@
  * FLEXCAN hardware feature flags
  *
  * Below is some version info we got:
- *    SOC   Version   IP-Version  Glitch-  [TR]WRN_INT
- *                                Filter?   connected?
- *   MX25  FlexCAN2  03.00.00.00     no         no
- *   MX28  FlexCAN2  03.00.04.00    yes        yes
- *   MX35  FlexCAN2  03.00.00.00     no         no

drivers/net/can/flexcan.c line 181

Quoted 10 lines

drivers/net/can/flexcan.c +8 -2

- *   MX53  FlexCAN2  03.00.00.00    yes         no
- *   MX6s  FlexCAN3  10.00.12.00    yes        yes
+ *    SOC   Version   IP-Version  Glitch-  [TR]WRN_INT  Memory err
+ *                                Filter?   connected?  detection
+ *   MX25  FlexCAN2  03.00.00.00     no         no         no
+ *   MX28  FlexCAN2  03.00.04.00    yes        yes         no
+ *   MX35  FlexCAN2  03.00.00.00     no         no         no
+ *   MX53  FlexCAN2  03.00.00.00    yes         no         no
+ *   MX6s  FlexCAN3  10.00.12.00    yes        yes         no
+ *   VF610 FlexCAN3  ?               no         no        yes

                                        ^^         ^^

Quoted 2 lines

Can you check the datasheet if the flexcan core has a "Glitch Filter Width Register (FLEXCANx_GFWR)"

There is no such register called GFWR/Glitch Filter or similar.

Quoted 3 lines

Can you check if the core generates a warning interrupt with the current setup, if you don't switch on bus error reporting? This means internally the [TR]WRN_INT is connected and works as specified.

Ok, so I disabled TWRNMSK (Bit 11) in the control register and printed out the error and status register (ESR1), this is what I get:

[  191.285295] flexcan_irq, esr=00040080
[  191.288996] flexcan_irq, ctrl=17092051

Bit 17 (TWRNINT) is not set while TWRNMSK is disabled. Hence [TR]WRN_INT is not connected?

--
Stefan

Stefan Agner

author reviewer

2014-07-25 10:50 UTC #9 lore raw

Re: [PATCH v3 4/4] can: flexcan: add vf610 support for FlexCAN

Am 2014-07-16 08:43, schrieb Stefan Agner:

Quoted 33 lines

Am 2014-07-15 16:24, schrieb Marc Kleine-Budde:
<snip>
Quoted 21 lines
Quoted 9 lines
drivers/net/can/flexcan.c +0 -5
@@ -150,18 +171,20 @@
  * FLEXCAN hardware feature flags
  *
  * Below is some version info we got:
- *    SOC   Version   IP-Version  Glitch-  [TR]WRN_INT
- *                                Filter?   connected?
- *   MX25  FlexCAN2  03.00.00.00     no         no
- *   MX28  FlexCAN2  03.00.04.00    yes        yes
- *   MX35  FlexCAN2  03.00.00.00     no         no
drivers/net/can/flexcan.c line 181
Quoted 10 lines
drivers/net/can/flexcan.c +8 -2
- *   MX53  FlexCAN2  03.00.00.00    yes         no
- *   MX6s  FlexCAN3  10.00.12.00    yes        yes
+ *    SOC   Version   IP-Version  Glitch-  [TR]WRN_INT  Memory err
+ *                                Filter?   connected?  detection
+ *   MX25  FlexCAN2  03.00.00.00     no         no         no
+ *   MX28  FlexCAN2  03.00.04.00    yes        yes         no
+ *   MX35  FlexCAN2  03.00.00.00     no         no         no
+ *   MX53  FlexCAN2  03.00.00.00    yes         no         no
+ *   MX6s  FlexCAN3  10.00.12.00    yes        yes         no
+ *   VF610 FlexCAN3  ?               no         no        yes
                                        ^^         ^^
Quoted 2 lines
Can you check the datasheet if the flexcan core has a "Glitch Filter Width Register (FLEXCANx_GFWR)"
There is no such register called GFWR/Glitch Filter or similar.
Quoted 3 lines
Can you check if the core generates a warning interrupt with the current setup, if you don't switch on bus error reporting? This means internally the [TR]WRN_INT is connected and works as specified.

Quoted 7 lines

Ok, so I disabled TWRNMSK (Bit 11) in the control register and printed out the error and status register (ESR1), this is what I get:
[  191.285295] flexcan_irq, esr=00040080
[  191.288996] flexcan_irq, ctrl=17092051
Bit 17 (TWRNINT) is not set while TWRNMSK is disabled. Hence [TR]WRN_INT is not connected?

Ping. Anything open/to do from my side?

--
Stefan

Marc Kleine-Budde

maintainer

2014-07-25 13:33 UTC #10 lore raw

Re: [PATCH v3 4/4] can: flexcan: add vf610 support for FlexCAN

Quoted 39 lines · Stefan Agner

Am 2014-07-16 08:43, schrieb Stefan Agner:
Quoted 38 lines
Am 2014-07-15 16:24, schrieb Marc Kleine-Budde:
<snip>
Quoted 21 lines
Quoted 9 lines
drivers/net/can/flexcan.c +0 -5
@@ -150,18 +171,20 @@
  * FLEXCAN hardware feature flags
  *
  * Below is some version info we got:
- *    SOC   Version   IP-Version  Glitch-  [TR]WRN_INT
- *                                Filter?   connected?
- *   MX25  FlexCAN2  03.00.00.00     no         no
- *   MX28  FlexCAN2  03.00.04.00    yes        yes
- *   MX35  FlexCAN2  03.00.00.00     no         no
drivers/net/can/flexcan.c line 181
Quoted 10 lines
drivers/net/can/flexcan.c +8 -2
- *   MX53  FlexCAN2  03.00.00.00    yes         no
- *   MX6s  FlexCAN3  10.00.12.00    yes        yes
+ *    SOC   Version   IP-Version  Glitch-  [TR]WRN_INT  Memory err
+ *                                Filter?   connected?  detection
+ *   MX25  FlexCAN2  03.00.00.00     no         no         no
+ *   MX28  FlexCAN2  03.00.04.00    yes        yes         no
+ *   MX35  FlexCAN2  03.00.00.00     no         no         no
+ *   MX53  FlexCAN2  03.00.00.00    yes         no         no
+ *   MX6s  FlexCAN3  10.00.12.00    yes        yes         no
+ *   VF610 FlexCAN3  ?               no         no        yes
                                        ^^         ^^
Quoted 2 lines
Can you check the datasheet if the flexcan core has a "Glitch Filter Width Register (FLEXCANx_GFWR)"
There is no such register called GFWR/Glitch Filter or similar.
Quoted 3 lines
Can you check if the core generates a warning interrupt with the current setup, if you don't switch on bus error reporting? This means internally the [TR]WRN_INT is connected and works as specified.
Ok, so I disabled TWRNMSK (Bit 11) in the control register and printed out the error and status register (ESR1), this is what I get:
[  191.285295] flexcan_irq, esr=00040080
[  191.288996] flexcan_irq, ctrl=17092051

Quoted 4 lines

Quoted 2 lines
Bit 17 (TWRNINT) is not set while TWRNMSK is disabled. Hence [TR]WRN_INT is not connected?
Ping. Anything open/to do from my side?

Please keep the printing of esr and ctrl in the interrupt handler, add a #define DEBUG in the driver, but do not change anything else. Then:

start the driver as usual:
- configure bitrate
- ifconfig can0 up
- _do_not_ enable bit error reporint
- start candump from gitorious with:
candump -e any,0:0,#FFFFFFFF
- short circuit CAN-High and CAN-Low
- send a CAN frame

Another test is to setup a proper CAN bus, but configure the a second CAN node with a different bitrate. Start the can0 on vf610 as usual, then candump -e any,0:0,#FFFFFFFF, but do not send any CAN frames on the vf610. Then on the other system keep sending CAN frames, you might have to restart the CAN on the second system....

Please send the outputs of candump and demsg to the list. It should generate a warning, error passive and finally a busoff message.

Marc

Signature · 12 lines

Pengutronix e.K.                  | Marc Kleine-Budde           |
Industrial Linux Solutions        | Phone: +49-231-2826-924     |
Vertretung West/Dortmund          | Fax:   +49-5121-206917-5555 |
Amtsgericht Hildesheim, HRA 2686  | http://www.pengutronix.de   |

-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 242 bytes
Desc: OpenPGP digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20140725/b64a1efe/attachment.sig>

Stefan Agner

author reviewer

2014-07-28 16:19 UTC #11 lore raw

Re: [PATCH v3 4/4] can: flexcan: add vf610 support for FlexCAN

Am 2014-07-25 15:33, schrieb Marc Kleine-Budde:

Quoted 40 lines · Stefan Agner

Quoted 39 lines
Am 2014-07-16 08:43, schrieb Stefan Agner:
Quoted 38 lines
Am 2014-07-15 16:24, schrieb Marc Kleine-Budde:
<snip>
Quoted 21 lines
Quoted 9 lines
(quoted diff) +0 -5
@@ -150,18 +171,20 @@
  * FLEXCAN hardware feature flags
  *
  * Below is some version info we got:
- *    SOC   Version   IP-Version  Glitch-  [TR]WRN_INT
- *                                Filter?   connected?
- *   MX25  FlexCAN2  03.00.00.00     no         no
- *   MX28  FlexCAN2  03.00.04.00    yes        yes
- *   MX35  FlexCAN2  03.00.00.00     no         no
Review line 181
Quoted 10 lines
(quoted diff) +8 -2
- *   MX53  FlexCAN2  03.00.00.00    yes         no
- *   MX6s  FlexCAN3  10.00.12.00    yes        yes
+ *    SOC   Version   IP-Version  Glitch-  [TR]WRN_INT  Memory err
+ *                                Filter?   connected?  detection
+ *   MX25  FlexCAN2  03.00.00.00     no         no         no
+ *   MX28  FlexCAN2  03.00.04.00    yes        yes         no
+ *   MX35  FlexCAN2  03.00.00.00     no         no         no
+ *   MX53  FlexCAN2  03.00.00.00    yes         no         no
+ *   MX6s  FlexCAN3  10.00.12.00    yes        yes         no
+ *   VF610 FlexCAN3  ?               no         no        yes
                                        ^^         ^^
Quoted 2 lines
Can you check the datasheet if the flexcan core has a "Glitch Filter Width Register (FLEXCANx_GFWR)"
There is no such register called GFWR/Glitch Filter or similar.
Quoted 3 lines
Can you check if the core generates a warning interrupt with the current setup, if you don't switch on bus error reporting? This means internally the [TR]WRN_INT is connected and works as specified.
Ok, so I disabled TWRNMSK (Bit 11) in the control register and printed out the error and status register (ESR1), this is what I get:
[  191.285295] flexcan_irq, esr=00040080
[  191.288996] flexcan_irq, ctrl=17092051

Quoted 8 lines

Quoted 4 lines
Quoted 2 lines
Bit 17 (TWRNINT) is not set while TWRNMSK is disabled. Hence [TR]WRN_INT is not connected?
Ping. Anything open/to do from my side?
Please keep the printing of esr and ctrl in the interrupt handler, add a #define DEBUG in the driver, but do not change anything else. Then:

Ok, my changes look like this:

drivers/net/can/flexcan.c +1 -0

index 1c31a5d..fe8b81c 100644
@@ -19,6 +19,7 @@
  *
  */
 
+#define DEBUG
 #include <linux/netdevice.h>
 #include <linux/can.h>
 #include <linux/can/dev.h>

@@ -743,6 +744,9 @@ static irqreturn_t flexcan_irq(int irq, void

*dev_id)

        reg_iflag1 = flexcan_read(&regs->iflag1);
        reg_esr = flexcan_read(&regs->esr);

+
+ printk("flexcan_irq, esr=%08x\n", reg_esr);
+ printk("flexcan_irq, ctrl=%08x\n", flexcan_read(&regs->ctrl));
/* ACK all bus error and state change IRQ sources */ if (reg_esr & FLEXCAN_ESR_ALL_INT)
flexcan_write(reg_esr & FLEXCAN_ESR_ALL_INT,
&regs->esr);
@@ -885,8 +889,8 @@ static int flexcan_chip_start(struct net_device *dev)

         */
        reg_ctrl = flexcan_read(&regs->ctrl);
        reg_ctrl &= ~FLEXCAN_CTRL_TSYN;

- reg_ctrl |= FLEXCAN_CTRL_BOFF_REC | FLEXCAN_CTRL_LBUF |
- FLEXCAN_CTRL_ERR_STATE;
+ reg_ctrl |= FLEXCAN_CTRL_BOFF_REC | FLEXCAN_CTRL_LBUF;// |
+ //FLEXCAN_CTRL_ERR_STATE;
/*
* enable the "error interrupt" (FLEXCAN_CTRL_ERR_MSK),
* on most Flexcan cores, too. Otherwise we don't get

I'm not sure whether you really want to keep the FLEXCAN_CTRL_ERR_STATE commented out...

Quoted 8 lines

start the driver as usual:
- configure bitrate
- ifconfig can0 up
- _do_not_ enable bit error reporint
- start candump from gitorious with:
candump -e any,0:0,#FFFFFFFF
- short circuit CAN-High and CAN-Low
- send a CAN frame

root@colibri-vf:~# ip link set can0 type can bitrate 500000
[  146.140862] flexcan 40020000.flexcan can0: bitrate error 0.7%
root@colibri-vf:~# ip link set can0 up
[  146.661430] flexcan 40020000.flexcan can0: writing ctrl=0x17092001
[  146.667902] flexcan 40020000.flexcan can0: flexcan_set_bittiming:
mcr=0x5980000f ctrl=0x17092001
[  146.676790] flexcan 40020000.flexcan can0: flexcan_chip_start:
writing mcr=0x79a20208
[  146.684709] flexcan 40020000.flexcan can0: flexcan_chip_start:
writing ctrl=0x17092051
[  146.698228] flexcan 40020000.flexcan can0: flexcan_chip_start:
reading mcr=0x60a20208 ctrl=0x1709205

# cansend can0 1F334455#1122334455667788
interface = can0, family = 29, type = 3, proto =

Nothing happens on candump.

Quoted 5 lines

Another test is to setup a proper CAN bus, but configure the a second CAN node with a different bitrate. Start the can0 on vf610 as usual, then candump -e any,0:0,#FFFFFFFF, but do not send any CAN frames on the vf610. Then on the other system keep sending CAN frames, you might have to restart the CAN on the second system....

I'm using a PCAN-USB from Peak System for this test. When running with the same bitrates on both sides (500000, things work smoothly as expected:

# ip link set can0 type can bitrate 500000
# ip link set can0 up
# cansend can0 1F334455#1122334455667788

root@colibri-vf:~# ./candump -e any,0:0,#FFFFFFFF
  can0  1F334455   [8]  11 22 33 44 55 66 77 88

dmesg:

[  541.772502] flexcan_irq, esr=00040180
[  541.776207] flexcan_irq, ctrl=17092051

Then I reconfigure the system on my host:

# ip link set can0 down
# ip link set can0 type can bitrate 1000000
# ip link set can0 up
# cansend can0 1F334455#1122334455667788

Nothing happens on Vybrid side.

However, I got once this Kernel panic after I reconfigured to normal mode. But I could not reproduce this.

[  461.954394] flexcan_irq, esr=00059d82
[  461.958093] flexcan_irq, ctrl=17092051
[  461.961873] ------------[ cut here ]------------
[  461.966536] WARNING: CPU: 0 PID: 0 at kernel/locking/mutex.c:826
mutex_trylock+0x1b0/0x208()
[  461.974982] DEBUG_LOCKS_WARN_ON(in_interrupt())
[  461.979347] Modules linked in:
[  461.982621] CPU: 0 PID: 0 Comm: swapper/0 Not tainted
3.16.0-rc4-00017-ge9a974f-dirty #215
[  461.990896] Backtrace:
[  461.993412] [<80011e1c>] (dump_backtrace) from [<80011fb8>]
(show_stack+0x18/0x1c)
[  462.000991]  r6:806718ec r5:00000000 r4:00000000 r3:00000000
[  462.006836] [<80011fa0>] (show_stack) from [<8066e160>]
(dump_stack+0x88/0xa4)
[  462.014143] [<8066e0d8>] (dump_stack) from [<80028f48>]
(warn_slowpath_common+0x70/0x94)
[  462.022280]  r5:00000009 r4:808f9d50
[  462.025920] [<80028ed8>] (warn_slowpath_common) from [<80029010>]
(warn_slowpath_fmt+0x38/0x40)
[  462.034666]  r8:808f9e14 r7:8110cf7c r6:804c2fa0 r5:8e9ee000
r4:8094cdcc
[  462.041478] [<80028fdc>] (warn_slowpath_fmt) from [<806718ec>]
(mutex_trylock+0x1b0/0x208)
[  462.049792]  r3:807e3f6c r2:807e1b8c
[  462.053466] [<8067173c>] (mutex_trylock) from [<804c2fa0>]
(clk_prepare_lock+0x14/0xec)
[  462.061479]  r7:90880000 r6:8e81f800 r5:8e9ee000 r4:8e81f800
[  462.067280] [<804c2f8c>] (clk_prepare_lock) from [<804c50d0>]
(clk_prepare+0x14/0x2c)
[  462.075158]  r6:8e81f800 r5:8e9ee000 r4:8e81f800 r3:00000000
[  462.080918] [<804c50bc>] (clk_prepare) from [<803e7a50>]
(flexcan_get_berr_counter+0x24/0xd0)
[  462.089487]  r4:00000001 r3:00000000
[  462.093156] [<803e7a2c>] (flexcan_get_berr_counter) from [<803e895c>]
(flexcan_poll+0x40c/0x58c)
[  462.101992]  r8:0000000a r7:0000000a r6:8e372388 r5:8e172a80
r4:00000001 r3:00000000
[  462.109843] [<803e8550>] (flexcan_poll) from [<80511f90>]
(net_rx_action+0xcc/0x1b4)
[  462.117630]  r10:8e9ee6c0 r9:00000003 r8:0000000a r7:8fdde188
r6:808fa0c0 r5:8fdde180
[  462.125587]  r4:0000012c
[  462.128164] [<80511ec4>] (net_rx_action) from [<8002d290>]
(__do_softirq+0x120/0x26c)
[  462.136038]  r10:808fa080 r9:00000003 r8:00000100 r7:00000003
r6:808f8000 r5:808fa08c
[  462.143994]  r4:00000000
[  462.146566] [<8002d170>] (__do_softirq) from [<8002d6d4>]
(irq_exit+0xb0/0x104)
[  462.153923]  r10:806788ac r9:808f8000 r8:00000000 r7:0000005a
r6:808f8000 r5:808f5e2c
[  462.161877]  r4:808f8000
[  462.164459] [<8002d624>] (irq_exit) from [<8000f4bc>]
(handle_IRQ+0x58/0xb8)
[  462.171520]  r4:80900d2c r3:000000a0
[  462.175200] [<8000f464>] (handle_IRQ) from [<800086c0>]
(gic_handle_irq+0x30/0x68)
[  462.182818]  r8:8095c587 r7:90802100 r6:808f9f28 r5:80900ea0
r4:9080210c r3:000000a0
[  462.190671] [<80008690>] (gic_handle_irq) from [<80012ae4>]
(__irq_svc+0x44/0x5c)
[  462.198203] Exception stack(0x808f9f28 to 0x808f9f70)
[  462.203315] 9f20:                   00000001 00000001 00000000
80904070 8090098c 80900938
[  462.211517] 9f40: 8095c587 00000000 8095c587 808f8000 806788ac
808f9f7c 808f9f40 808f9f70
[  462.219746] 9f60: 80066a98 8000f834 20000013 ffffffff
[  462.224852]  r7:808f9f5c r6:ffffffff r5:20000013 r4:8000f834
[  462.230621] [<8000f80c>] (arch_cpu_idle) from [<8005fba4>]
(cpu_startup_entry+0x104/0x16c)
[  462.238964] [<8005faa0>] (cpu_startup_entry) from [<80668cf8>]
(rest_init+0xb0/0xd8)
[  462.246757]  r7:8ffffcc0 r3:00000000
[  462.250419] [<80668c48>] (rest_init) from [<808a5bf8>]
(start_kernel+0x340/0x3ac)
[  462.257979]  r5:8095c7c0 r4:80900a38
[  462.261620] [<808a58b8>] (start_kernel) from [<80008074>]
(0x80008074)
[  462.268204] ---[ end trace c9c9dee0ce2272a7 ]---
[  462.272899] flexcan 40020000.flexcan can0: Error Warning IRQ

candump showed this:
can0 20000004 [8] 00 04 00 00 00 00 00 00 ERRORFRAME

	controller-problem{rx-error-warning}

Quoted 4 lines

Please send the outputs of candump and demsg to the list. It should generate a warning, error passive and finally a busoff message.

--
Stefan

Marc Kleine-Budde

maintainer

2014-07-28 16:28 UTC #12 lore raw

Re: [PATCH v3 4/4] can: flexcan: add vf610 support for FlexCAN

Quoted 4 lines · Stefan Agner

Quoted 4 lines
Quoted 1 line
Ping. Anything open/to do from my side?
Please keep the printing of esr and ctrl in the interrupt handler, add a #define DEBUG in the driver, but do not change anything else. Then:

                                    ^^^^^^^^^^^^^^^^^^^^^^^^^^^

drivers/net/can/flexcan.c line 22

Quoted 10 lines

drivers/net/can/flexcan.c +1 -0

index 1c31a5d..fe8b81c 100644
@@ -19,6 +19,7 @@
  *
  */
 
+#define DEBUG

keep

drivers/net/can/flexcan.c static irqreturn_t flexcan_irq(int irq, void · line 750

Quoted 11 lines

drivers/net/can/flexcan.c +3 -0

 #include <linux/netdevice.h>
 #include <linux/can.h>
 #include <linux/can/dev.h>

@@ -743,6 +744,9 @@ static irqreturn_t flexcan_irq(int irq, void
 *dev_id)
 
        reg_iflag1 = flexcan_read(&regs->iflag1);
        reg_esr = flexcan_read(&regs->esr);
+
+       printk("flexcan_irq, esr=%08x\n", reg_esr);
+       printk("flexcan_irq, ctrl=%08x\n", flexcan_read(&regs->ctrl));

keep

Quoted 17 lines

drivers/net/can/flexcan.c +0 -0

        /* ACK all bus error and state change IRQ sources */
        if (reg_esr & FLEXCAN_ESR_ALL_INT)

flexcan_write(reg_esr & FLEXCAN_ESR_ALL_INT,
&regs->esr);

drivers/net/can/flexcan.c +2 -2

@@ -885,8 +889,8 @@ static int flexcan_chip_start(struct net_device
 *dev)
         */
        reg_ctrl = flexcan_read(&regs->ctrl);
        reg_ctrl &= ~FLEXCAN_CTRL_TSYN;
-       reg_ctrl |= FLEXCAN_CTRL_BOFF_REC | FLEXCAN_CTRL_LBUF |
-               FLEXCAN_CTRL_ERR_STATE;
+       reg_ctrl |= FLEXCAN_CTRL_BOFF_REC | FLEXCAN_CTRL_LBUF;// |
+               //FLEXCAN_CTRL_ERR_STATE;
        /*
         * enable the "error interrupt" (FLEXCAN_CTRL_ERR_MSK),

* on most Flexcan cores, too. Otherwise we don't get

Quoted 2 lines

I'm not sure whether you really want to keep the FLEXCAN_CTRL_ERR_STATE commented out...

No, please remove this change and redo the test.

Marc

Signature · 12 lines

Pengutronix e.K.                  | Marc Kleine-Budde           |
Industrial Linux Solutions        | Phone: +49-231-2826-924     |
Vertretung West/Dortmund          | Fax:   +49-5121-206917-5555 |
Amtsgericht Hildesheim, HRA 2686  | http://www.pengutronix.de   |

-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 242 bytes
Desc: OpenPGP digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20140728/af1eab34/attachment.sig>

Stefan Agner

author reviewer

2014-07-29 07:28 UTC #13 lore raw

Re: [PATCH v3 4/4] can: flexcan: add vf610 support for FlexCAN

Am 2014-07-28 18:28, schrieb Marc Kleine-Budde:

Quoted 6 lines · Stefan Agner

Quoted 2 lines
I'm not sure whether you really want to keep the FLEXCAN_CTRL_ERR_STATE commented out...
No, please remove this change and redo the test.

Ok, removed that change and did the tests again:

== Wrong Bitrate test

[  146.485022] flexcan 40020000.flexcan can0: bitrate error 0.7%
[  148.401793] flexcan 40020000.flexcan can0: writing ctrl=0x17092001
[  148.408263] flexcan 40020000.flexcan can0: flexcan_set_bittiming:
mcr=0x5980000f ctrl=0x17092001
[  148.408298] flexcan 40020000.flexcan can0: flexcan_chip_start:
writing mcr=0x79a20208
[  148.408328] flexcan 40020000.flexcan can0: flexcan_chip_start:
writing ctrl=0x1709ac51
[  148.414373] flexcan 40020000.flexcan can0: flexcan_chip_start:
reading mcr=0x60a20208 ctrl=0x1709ac51
^---- Initialization
[  152.968685] flexcan_irq, esr=00040080
[  152.972386] flexcan_irq, ctrl=1709ac51
[  155.488623] flexcan_irq, esr=00040080
[  155.492326] flexcan_irq, ctrl=1709ac51
^---- Two messages with right bitrate
[  171.014124] flexcan_irq, esr=00058d0a
[  171.017823] flexcan_irq, ctrl=1709ac51
^---- One message with wrong bitrate
[  171.021631] flexcan 40020000.flexcan can0: Error Warning IRQ
[  171.021660] flexcan 40020000.flexcan can0: Error Passive IRQ

# ./candump -e any,0:0,#FFFFFFFF
  can0  1F334455   [8]  11 22 33 44 55 66 77 88
  can0  1F334455   [8]  11 22 33 44 55 66 77 88
  can0  20000004   [8]  00 10 00 00 00 00 00 00   ERRORFRAME
	controller-problem{rx-error-passive}

== Loopback test

[  464.003776] flexcan 40020000.flexcan can0: writing ctrl=0x17092051
[  464.010005] flexcan 40020000.flexcan can0: flexcan_set_bittiming:
mcr=0x5980000f ctrl=0x17092051
[  464.010035] flexcan 40020000.flexcan can0: flexcan_chip_start:
writing mcr=0x79a20208
[  464.010064] flexcan 40020000.flexcan can0: flexcan_chip_start:
writing ctrl=0x1709ac51
[  464.010199] flexcan 40020000.flexcan can0: flexcan_chip_start:
reading mcr=0x60a20208 ctrl=0x1709ac51
[  464.011682] IPv6: ADDRCONF(NETDEV_CHANGE): can0: link becomes ready
[  470.970133] flexcan_irq, esr=00064252
[  470.974833] flexcan_irq, ctrl=1709ac51
[  470.980171] flexcan 40020000.flexcan can0: Error Warning IRQ
[  470.980203] flexcan 40020000.flexcan can0: Error Passive IRQ
[  470.980328] flexcan_irq, esr=00000034
[  470.984998] flexcan_irq, ctrl=1709ac51

# ./candump -e any,0:0,#FFFFFFFF
  can0  20000044   [8]  00 10 00 00 00 00 00 00   ERRORFRAME
	controller-problem{rx-error-passive}
	bus-off

--
Stefan

Marc Kleine-Budde

maintainer

2014-07-30 11:47 UTC #14 lore raw

Re: [PATCH v3 4/4] can: flexcan: add vf610 support for FlexCAN

Quoted 25 lines · Stefan Agner

Am 2014-07-28 18:28, schrieb Marc Kleine-Budde:
Quoted 6 lines · Stefan Agner
Quoted 2 lines
I'm not sure whether you really want to keep the FLEXCAN_CTRL_ERR_STATE commented out...
No, please remove this change and redo the test.
Ok, removed that change and did the tests again:
== Wrong Bitrate test
[  146.485022] flexcan 40020000.flexcan can0: bitrate error 0.7%
[  148.401793] flexcan 40020000.flexcan can0: writing ctrl=0x17092001
[  148.408263] flexcan 40020000.flexcan can0: flexcan_set_bittiming:
mcr=0x5980000f ctrl=0x17092001
[  148.408298] flexcan 40020000.flexcan can0: flexcan_chip_start:
writing mcr=0x79a20208
[  148.408328] flexcan 40020000.flexcan can0: flexcan_chip_start:
writing ctrl=0x1709ac51
[  148.414373] flexcan 40020000.flexcan can0: flexcan_chip_start:
reading mcr=0x60a20208 ctrl=0x1709ac51
^---- Initialization
[  152.968685] flexcan_irq, esr=00040080
[  152.972386] flexcan_irq, ctrl=1709ac51

Quoted 8 lines

[  155.488623] flexcan_irq, esr=00040080
[  155.492326] flexcan_irq, ctrl=1709ac51
^---- Two messages with right bitrate
[  171.014124] flexcan_irq, esr=00058d0a
[  171.017823] flexcan_irq, ctrl=1709ac51
^---- One message with wrong bitrate
[  171.021631] flexcan 40020000.flexcan can0: Error Warning IRQ
[  171.021660] flexcan 40020000.flexcan can0: Error Passive IRQ

Thanks for the test, so far looks promising :) With this setup the other CAN node repeats the CAN frame until it's ACKed. Because there is no node with a compatible bitrate, there is no ACking CAN node.

Can you add a third CAN node to the network. The second and third node should use the same bitrate, while your vf610 uses a different one. With the new setup it should take more than one frame until the vf610 goes into error warning and even more frames to error passive. This way we can see it the error warning interrupt is connected or not. The error counters should increase with each "wrong" bitrate frame it sees, you can check with:

ip -details link show can0

The output looks like this:

Quoted 3 lines

4: can0: <NOARP,UP,LOWER_UP,ECHO> mtu 16 qdisc pfifo_fast state UNKNOWN mode DEFAULT qlen 10
link/can
can state ERROR-ACTIVE (berr-counter tx 0 rx 0) restart-ms 0

                              ^^^^^^^^^^^^^^^^^^^^^^

Quoted 4 lines

    bitrate 1000000 sample-point 0.750
    tq 125 prop-seg 2 phase-seg1 3 phase-seg2 2 sjw 1
    sja1000: tseg1 1..16 tseg2 1..8 sjw 1..4 brp 1..64 brp-inc 1
    clock 8000000

When one of the berr-counter crosses 96 (and stays below 128) a warning interrupt should be generated.

Marc

Signature · 12 lines

Pengutronix e.K.                  | Marc Kleine-Budde           |
Industrial Linux Solutions        | Phone: +49-231-2826-924     |
Vertretung West/Dortmund          | Fax:   +49-5121-206917-5555 |
Amtsgericht Hildesheim, HRA 2686  | http://www.pengutronix.de   |

-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 242 bytes
Desc: OpenPGP digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20140730/26fb27c6/attachment.sig>

Stefan Agner

author reviewer

2014-08-04 13:43 UTC #15 lore raw

Re: [PATCH v3 4/4] can: flexcan: add vf610 support for FlexCAN

Am 2014-07-30 13:47, schrieb Marc Kleine-Budde:

Quoted 54 lines · Stefan Agner

Quoted 25 lines
Am 2014-07-28 18:28, schrieb Marc Kleine-Budde:
Quoted 6 lines · Stefan Agner
Quoted 2 lines
I'm not sure whether you really want to keep the FLEXCAN_CTRL_ERR_STATE commented out...
No, please remove this change and redo the test.
Ok, removed that change and did the tests again:
== Wrong Bitrate test
[  146.485022] flexcan 40020000.flexcan can0: bitrate error 0.7%
[  148.401793] flexcan 40020000.flexcan can0: writing ctrl=0x17092001
[  148.408263] flexcan 40020000.flexcan can0: flexcan_set_bittiming:
mcr=0x5980000f ctrl=0x17092001
[  148.408298] flexcan 40020000.flexcan can0: flexcan_chip_start:
writing mcr=0x79a20208
[  148.408328] flexcan 40020000.flexcan can0: flexcan_chip_start:
writing ctrl=0x1709ac51
[  148.414373] flexcan 40020000.flexcan can0: flexcan_chip_start:
reading mcr=0x60a20208 ctrl=0x1709ac51
^---- Initialization
[  152.968685] flexcan_irq, esr=00040080
[  152.972386] flexcan_irq, ctrl=1709ac51
Quoted 8 lines
[  155.488623] flexcan_irq, esr=00040080
[  155.492326] flexcan_irq, ctrl=1709ac51
^---- Two messages with right bitrate
[  171.014124] flexcan_irq, esr=00058d0a
[  171.017823] flexcan_irq, ctrl=1709ac51
^---- One message with wrong bitrate
[  171.021631] flexcan 40020000.flexcan can0: Error Warning IRQ
[  171.021660] flexcan 40020000.flexcan can0: Error Passive IRQ
Thanks for the test, so far looks promising :) With this setup the other CAN node repeats the CAN frame until it's ACKed. Because there is no node with a compatible bitrate, there is no ACking CAN node.
Can you add a third CAN node to the network. The second and third node should use the same bitrate, while your vf610 uses a different one. With the new setup it should take more than one frame until the vf610 goes into error warning and even more frames to error passive. This way we can see it the error warning interrupt is connected or not. The error counters should increase with each "wrong" bitrate frame it sees, you can check with:
ip -details link show can0
The output looks like this:
Quoted 3 lines
4: can0: <NOARP,UP,LOWER_UP,ECHO> mtu 16 qdisc pfifo_fast state UNKNOWN mode DEFAULT qlen 10
link/can
can state ERROR-ACTIVE (berr-counter tx 0 rx 0) restart-ms 0

Quoted 8 lines

                              ^^^^^^^^^^^^^^^^^^^^^^

Quoted 4 lines

    bitrate 1000000 sample-point 0.750
    tq 125 prop-seg 2 phase-seg1 3 phase-seg2 2 sjw 1
    sja1000: tseg1 1..16 tseg2 1..8 sjw 1..4 brp 1..64 brp-inc 1
    clock 8000000

When one of the berr-counter crosses 96 (and stays below 128) a warning interrupt should be generated.

Ok, created this setup, could successfully communicate with all three nodes. I then set the Vybrid to half of the bitrate. When I send a frame from Vybrid, the berr-counter tx immediately ends up at 128 and the device is in ERROR-PASSIVE:

root at colibri-vf:~# ip -details link show can1
3: can1: <NOARP,UP,LOWER_UP,ECHO> mtu 16 qdisc pfifo_fast state UNKNOWN mode DEFAULT group default qlen 10
link/can promiscuity 0
can state ERROR-ACTIVE (berr-counter tx 0 rx 0) restart-ms 0 bitrate 124990 sample-point 0.739
tq 347 prop-seg 8 phase-seg1 8 phase-seg2 6 sjw 1
flexcan: tseg1 4..16 tseg2 2..8 sjw 1..4 brp 1..256 brp-inc 1 clock 83368421
root at colibri-vf:~# cansend can1 1F334455#1122334455667788 interface = can1, family = 29, type = 3, proto = 1
root at colibri-vf:~# [ 818.886664] flexcan_irq, esr=00062242

[  818.890365] flexcan_irq, ctrl=1c3dac57

root at colibri-vf:~# ip -details link show can1
3: can1: <NOARP,UP,LOWER_UP,ECHO> mtu 16 qdisc pfifo_fast state UNKNOWN mode DEFAULT group default qlen 10
link/can promiscuity 0
can state ERROR-PASSIVE (berr-counter tx 128 rx 0) restart-ms 0 bitrate 124990 sample-point 0.739
tq 347 prop-seg 8 phase-seg1 8 phase-seg2 6 sjw 1
flexcan: tseg1 4..16 tseg2 2..8 sjw 1..4 brp 1..256 brp-inc 1 clock 83368421

When I send the frames from another device on the bus, I can see the rx count incrementing by one on each frame I send. As you expected, the device changes to ERROR-WARNING when crossing the 96 frame boundary:

root at colibri-vf:~# ip -details link show can1
3: can1: <NOARP,UP,LOWER_UP,ECHO> mtu 16 qdisc pfifo_fast state UNKNOWN mode DEFAULT group default qlen 10
link/can promiscuity 0
can state ERROR-ACTIVE (berr-counter tx 0 rx 92) restart-ms 0 bitrate 124990 sample-point 0.739
tq 347 prop-seg 8 phase-seg1 8 phase-seg2 6 sjw 1
flexcan: tseg1 4..16 tseg2 2..8 sjw 1..4 brp 1..256 brp-inc 1 clock 83368421
root at colibri-vf:~# [ 448.331150] flexcan_irq, esr=0005050a

[  448.334851] flexcan_irq, ctrl=1c3dac57

ip -details link show can1
3: can1: <NOARP,UP,LOWER_UP,ECHO> mtu 16 qdisc pfifo_fast state UNKNOWN mode DEFAULT group default qlen 10
link/can promiscuity 0
can state ERROR-WARNING (berr-counter tx 0 rx 102) restart-ms 0 bitrate 124990 sample-point 0.739
tq 347 prop-seg 8 phase-seg1 8 phase-seg2 6 sjw 1
flexcan: tseg1 4..16 tseg2 2..8 sjw 1..4 brp 1..256 brp-inc 1 clock 83368421

However, once reaching 128, I don't get another interrupt and the device stays in ERROR-WARNING:

3: can1: <NOARP,UP,LOWER_UP,ECHO> mtu 16 qdisc pfifo_fast state UNKNOWN mode DEFAULT group default qlen 10
link/can promiscuity 0
can state ERROR-WARNING (berr-counter tx 0 rx 128) restart-ms 0 bitrate 124990 sample-point 0.739
tq 347 prop-seg 8 phase-seg1 8 phase-seg2 6 sjw 1
flexcan: tseg1 4..16 tseg2 2..8 sjw 1..4 brp 1..256 brp-inc 1 clock 83368421

Is this the expected behavior on receive?

--
Stefan

Marc Kleine-Budde

maintainer

2014-08-04 14:27 UTC #16 lore raw

Re: [PATCH v3 4/4] can: flexcan: add vf610 support for FlexCAN

On 08/04/2014 03:43 PM, Stefan Agner wrote:
[...]

Quoted 25 lines

Quoted 25 lines
Thanks for the test, so far looks promising :) With this setup the other CAN node repeats the CAN frame until it's ACKed. Because there is no node with a compatible bitrate, there is no ACking CAN node.
Can you add a third CAN node to the network. The second and third node should use the same bitrate, while your vf610 uses a different one. With the new setup it should take more than one frame until the vf610 goes into error warning and even more frames to error passive. This way we can see it the error warning interrupt is connected or not. The error counters should increase with each "wrong" bitrate frame it sees, you can check with:
ip -details link show can0
The output looks like this:
Quoted 3 lines
4: can0: <NOARP,UP,LOWER_UP,ECHO> mtu 16 qdisc pfifo_fast state UNKNOWN mode DEFAULT qlen 10
link/can
can state ERROR-ACTIVE (berr-counter tx 0 rx 0) restart-ms 0
                              ^^^^^^^^^^^^^^^^^^^^^^
Quoted 4 lines
    bitrate 1000000 sample-point 0.750
    tq 125 prop-seg 2 phase-seg1 3 phase-seg2 2 sjw 1
    sja1000: tseg1 1..16 tseg2 1..8 sjw 1..4 brp 1..64 brp-inc 1
    clock 8000000

Quoted 7 lines

Quoted 2 lines
When one of the berr-counter crosses 96 (and stays below 128) a warning interrupt should be generated.
Ok, created this setup, could successfully communicate with all three nodes. I then set the Vybrid to half of the bitrate. When I send a frame from Vybrid, the berr-counter tx immediately ends up at 128 and the device is in ERROR-PASSIVE:

This is expected.

Quoted 9 lines

root at colibri-vf:~# ip -details link show can1
3: can1: <NOARP,UP,LOWER_UP,ECHO> mtu 16 qdisc pfifo_fast state UNKNOWN mode DEFAULT group default qlen 10
link/can promiscuity 0
can state ERROR-ACTIVE (berr-counter tx 0 rx 0) restart-ms 0 bitrate 124990 sample-point 0.739
tq 347 prop-seg 8 phase-seg1 8 phase-seg2 6 sjw 1
flexcan: tseg1 4..16 tseg2 2..8 sjw 1..4 brp 1..256 brp-inc 1 clock 83368421

            ^^^^^^^^

BTW: the can core has a really weird clock rate, have a look at the datasheet if you manage to route a 24 MHz clock (or another multiple of 8MHz) to the flexcan core. I had a quick glance at the datasheet, if I understand it correctly the Fast OSC clock runs with 24 MHz.

Quoted 16 lines

root at colibri-vf:~# cansend can1 1F334455#1122334455667788 interface = can1, family = 29, type = 3, proto = 1 root at colibri-vf:~# [ 818.886664] flexcan_irq, esr=00062242
[  818.890365] flexcan_irq, ctrl=1c3dac57
root at colibri-vf:~# ip -details link show can1
3: can1: <NOARP,UP,LOWER_UP,ECHO> mtu 16 qdisc pfifo_fast state UNKNOWN mode DEFAULT group default qlen 10
link/can promiscuity 0
can state ERROR-PASSIVE (berr-counter tx 128 rx 0) restart-ms 0 bitrate 124990 sample-point 0.739
tq 347 prop-seg 8 phase-seg1 8 phase-seg2 6 sjw 1
flexcan: tseg1 4..16 tseg2 2..8 sjw 1..4 brp 1..256 brp-inc 1 clock 83368421

Quoted 3 lines

When I send the frames from another device on the bus, I can see the rx count incrementing by one on each frame I send. As you expected, the device changes to ERROR-WARNING when crossing the 96 frame boundary:

This is correct

Quoted 21 lines

root at colibri-vf:~# ip -details link show can1
3: can1: <NOARP,UP,LOWER_UP,ECHO> mtu 16 qdisc pfifo_fast state UNKNOWN mode DEFAULT group default qlen 10
link/can promiscuity 0
can state ERROR-ACTIVE (berr-counter tx 0 rx 92) restart-ms 0 bitrate 124990 sample-point 0.739
tq 347 prop-seg 8 phase-seg1 8 phase-seg2 6 sjw 1
flexcan: tseg1 4..16 tseg2 2..8 sjw 1..4 brp 1..256 brp-inc 1 clock 83368421
root at colibri-vf:~# [ 448.331150] flexcan_irq, esr=0005050a
[  448.334851] flexcan_irq, ctrl=1c3dac57
ip -details link show can1
3: can1: <NOARP,UP,LOWER_UP,ECHO> mtu 16 qdisc pfifo_fast state UNKNOWN mode DEFAULT group default qlen 10
link/can promiscuity 0
can state ERROR-WARNING (berr-counter tx 0 rx 102) restart-ms 0 bitrate 124990 sample-point 0.739
tq 347 prop-seg 8 phase-seg1 8 phase-seg2 6 sjw 1
flexcan: tseg1 4..16 tseg2 2..8 sjw 1..4 brp 1..256 brp-inc 1 clock 83368421

Quoted 2 lines

However, once reaching 128, I don't get another interrupt and the device stays in ERROR-WARNING:

The contents of the esr reg would be interesting, especially the FLT_CONF part.

Quoted 10 lines

3: can1: <NOARP,UP,LOWER_UP,ECHO> mtu 16 qdisc pfifo_fast state UNKNOWN mode DEFAULT group default qlen 10
link/can promiscuity 0
can state ERROR-WARNING (berr-counter tx 0 rx 128) restart-ms 0 bitrate 124990 sample-point 0.739
tq 347 prop-seg 8 phase-seg1 8 phase-seg2 6 sjw 1
flexcan: tseg1 4..16 tseg2 2..8 sjw 1..4 brp 1..256 brp-inc 1 clock 83368421
Is this the expected behavior on receive?

No, it should go into error passive if one of the error counters have >
127. Maybe this is an error onthe vf610, maybe it's a general flexcan problem.

Marc

Signature · 12 lines

Pengutronix e.K.                  | Marc Kleine-Budde           |
Industrial Linux Solutions        | Phone: +49-231-2826-924     |
Vertretung West/Dortmund          | Fax:   +49-5121-206917-5555 |
Amtsgericht Hildesheim, HRA 2686  | http://www.pengutronix.de   |

-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 242 bytes
Desc: OpenPGP digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20140804/2e218810/attachment.sig>

Stefan Agner

author reviewer

2014-08-04 16:01 UTC #17 lore raw

Re: [PATCH v3 4/4] can: flexcan: add vf610 support for FlexCAN

Am 2014-08-04 16:27, schrieb Marc Kleine-Budde:

Quoted 47 lines · Stefan Agner

[...]
Quoted 25 lines
Quoted 25 lines
Thanks for the test, so far looks promising :) With this setup the other CAN node repeats the CAN frame until it's ACKed. Because there is no node with a compatible bitrate, there is no ACking CAN node.
Can you add a third CAN node to the network. The second and third node should use the same bitrate, while your vf610 uses a different one. With the new setup it should take more than one frame until the vf610 goes into error warning and even more frames to error passive. This way we can see it the error warning interrupt is connected or not. The error counters should increase with each "wrong" bitrate frame it sees, you can check with:
ip -details link show can0
The output looks like this:
Quoted 3 lines
4: can0: <NOARP,UP,LOWER_UP,ECHO> mtu 16 qdisc pfifo_fast state UNKNOWN mode DEFAULT qlen 10
link/can
can state ERROR-ACTIVE (berr-counter tx 0 rx 0) restart-ms 0
                              ^^^^^^^^^^^^^^^^^^^^^^
Quoted 4 lines
    bitrate 1000000 sample-point 0.750
    tq 125 prop-seg 2 phase-seg1 3 phase-seg2 2 sjw 1
    sja1000: tseg1 1..16 tseg2 1..8 sjw 1..4 brp 1..64 brp-inc 1
    clock 8000000
Quoted 7 lines
Quoted 2 lines
When one of the berr-counter crosses 96 (and stays below 128) a warning interrupt should be generated.
Ok, created this setup, could successfully communicate with all three nodes. I then set the Vybrid to half of the bitrate. When I send a frame from Vybrid, the berr-counter tx immediately ends up at 128 and the device is in ERROR-PASSIVE:
This is expected.
Quoted 9 lines
root at colibri-vf:~# ip -details link show can1
3: can1: <NOARP,UP,LOWER_UP,ECHO> mtu 16 qdisc pfifo_fast state UNKNOWN mode DEFAULT group default qlen 10
link/can promiscuity 0
can state ERROR-ACTIVE (berr-counter tx 0 rx 0) restart-ms 0 bitrate 124990 sample-point 0.739
tq 347 prop-seg 8 phase-seg1 8 phase-seg2 6 sjw 1
flexcan: tseg1 4..16 tseg2 2..8 sjw 1..4 brp 1..256 brp-inc 1 clock 83368421

Quoted 7 lines

            ^^^^^^^^
BTW: the can core has a really weird clock rate, have a look at the datasheet if you manage to route a 24 MHz clock (or another multiple of 8MHz) to the flexcan core. I had a quick glance at the datasheet, if I understand it correctly the Fast OSC clock runs with 24 MHz.

This pinmux is actually part of the IPs CTRL register (see CLKSRC). Currently this is set unconditionally to peripheral clock, which is on my device 83.3 MHz (500MHz/6). This would be a bit bigger change. Just thinking how to implement this. Maybe we have to reference a third clock "osc" and a device tree property fsl,can-clock-osc which one can choose between "osc" and "per" what do you think?

Quoted 16 lines

Quoted 16 lines
root at colibri-vf:~# cansend can1 1F334455#1122334455667788 interface = can1, family = 29, type = 3, proto = 1 root at colibri-vf:~# [ 818.886664] flexcan_irq, esr=00062242
[  818.890365] flexcan_irq, ctrl=1c3dac57
root at colibri-vf:~# ip -details link show can1
3: can1: <NOARP,UP,LOWER_UP,ECHO> mtu 16 qdisc pfifo_fast state UNKNOWN mode DEFAULT group default qlen 10
link/can promiscuity 0
can state ERROR-PASSIVE (berr-counter tx 128 rx 0) restart-ms 0 bitrate 124990 sample-point 0.739
tq 347 prop-seg 8 phase-seg1 8 phase-seg2 6 sjw 1
flexcan: tseg1 4..16 tseg2 2..8 sjw 1..4 brp 1..256 brp-inc 1 clock 83368421

Quoted 6 lines

Quoted 3 lines
When I send the frames from another device on the bus, I can see the rx count incrementing by one on each frame I send. As you expected, the device changes to ERROR-WARNING when crossing the 96 frame boundary:
This is correct

Just found out when using too high bitrate (500000 vs 125000), the error counter immediately goes up to 128 (or even beyond) and ends up in ERROR-PASSIVE:

# ip -details link show can1
[  292.164820] flexcan_get_berr_counter, esr=00000000
[  292.169715] flexcan_get_berr_counter, esr=00040190
3: can1: <NOARP,UP,LOWER_UP,ECHO> mtu 16 qdisc pfifo_fast state UNKNOWN
mode DEFAULT group default qlen 10
    link/can  promiscuity 0
    can state ERROR-PASSIVE (berr-counter tx 0 rx 135) restart-ms 0
    bitrate 298811 sample-point 0.777
    tq 371 prop-seg 3 phase-seg1 3 phase-seg2 2 sjw 1
    flexcan: tseg1 4..16 tseg2 2..8 sjw 1..4 brp 1..256 brp-inc 1
    clock 83368421

Quoted 21 lines

Quoted 20 lines
root at colibri-vf:~# ip -details link show can1
3: can1: <NOARP,UP,LOWER_UP,ECHO> mtu 16 qdisc pfifo_fast state UNKNOWN mode DEFAULT group default qlen 10
link/can promiscuity 0
can state ERROR-ACTIVE (berr-counter tx 0 rx 92) restart-ms 0 bitrate 124990 sample-point 0.739
tq 347 prop-seg 8 phase-seg1 8 phase-seg2 6 sjw 1
flexcan: tseg1 4..16 tseg2 2..8 sjw 1..4 brp 1..256 brp-inc 1 clock 83368421
root at colibri-vf:~# [ 448.331150] flexcan_irq, esr=0005050a
[  448.334851] flexcan_irq, ctrl=1c3dac57
ip -details link show can1
3: can1: <NOARP,UP,LOWER_UP,ECHO> mtu 16 qdisc pfifo_fast state UNKNOWN mode DEFAULT group default qlen 10
link/can promiscuity 0
can state ERROR-WARNING (berr-counter tx 0 rx 102) restart-ms 0 bitrate 124990 sample-point 0.739
tq 347 prop-seg 8 phase-seg1 8 phase-seg2 6 sjw 1
flexcan: tseg1 4..16 tseg2 2..8 sjw 1..4 brp 1..256 brp-inc 1 clock 83368421

Quoted 6 lines

Quoted 2 lines
However, once reaching 128, I don't get another interrupt and the device stays in ERROR-WARNING:
The contents of the esr reg would be interesting, especially the FLT_CONF part.

root at vybridvf61-v11:~# [ 222.221651] flexcan_irq, esr=0005050a

[  222.225349] flexcan_irq, ctrl=1c3dac57
ip -details link show can1
[  223.791082] flexcan_get_berr_counter, esr=00000000
[  223.796246] flexcan_get_berr_counter, esr=00040180

3: can1: <NOARP,UP,LOWER_UP,ECHO> mtu 16 qdisc pfifo_fast state UNKNOWN mode DEFAULT group default qlen
10
link/can promiscuity 0
can state ERROR-WARNING (berr-counter tx 0 rx 96) restart-ms 0 bitrate 124990 sample-point 0.739
tq 347 prop-seg 8 phase-seg1 8 phase-seg2 6 sjw 1
flexcan: tseg1 4..16 tseg2 2..8 sjw 1..4 brp 1..256 brp-inc 1 clock 83368421
root at vybridvf61-v11:~# ip -details link show can1

[  243.571175] flexcan_get_berr_counter, esr=00000000
[  243.576343] flexcan_get_berr_counter, esr=00040582

3: can1: <NOARP,UP,LOWER_UP,ECHO> mtu 16 qdisc pfifo_fast state UNKNOWN mode DEFAULT group default qlen
10
link/can promiscuity 0
can state ERROR-WARNING (berr-counter tx 0 rx 104) restart-ms 0 bitrate 124990 sample-point 0.739
tq 347 prop-seg 8 phase-seg1 8 phase-seg2 6 sjw 1
flexcan: tseg1 4..16 tseg2 2..8 sjw 1..4 brp 1..256 brp-inc 1 clock 83368421

...

root at vybridvf61-v11:~# ip -details link show can1

[  299.831192] flexcan_get_berr_counter, esr=00000000
[  299.836358] flexcan_get_berr_counter, esr=00040582

3: can1: <NOARP,UP,LOWER_UP,ECHO> mtu 16 qdisc pfifo_fast state UNKNOWN mode DEFAULT group default qlen 10
link/can promiscuity 0
can state ERROR-WARNING (berr-counter tx 0 rx 126) restart-ms 0 bitrate 124990 sample-point 0.739
tq 347 prop-seg 8 phase-seg1 8 phase-seg2 6 sjw 1
flexcan: tseg1 4..16 tseg2 2..8 sjw 1..4 brp 1..256 brp-inc 1 clock 83368421
root at vybridvf61-v11:~# ip -details link show can1

[  302.411025] flexcan_get_berr_counter, esr=00000000
[  302.416195] flexcan_get_berr_counter, esr=00040592

The FLTCONF is in Error Passive, however the stack did not received that information. I still have the printk in the interrupt, however I did not get an interrupt here (while I get one when it switched to ERROR-WARNING... But it looks like the ERRINT is still pending...

Quoted 9 lines

Quoted 9 lines
3: can1: <NOARP,UP,LOWER_UP,ECHO> mtu 16 qdisc pfifo_fast state UNKNOWN mode DEFAULT group default qlen 10
link/can promiscuity 0
can state ERROR-WARNING (berr-counter tx 0 rx 128) restart-ms 0 bitrate 124990 sample-point 0.739
tq 347 prop-seg 8 phase-seg1 8 phase-seg2 6 sjw 1
flexcan: tseg1 4..16 tseg2 2..8 sjw 1..4 brp 1..256 brp-inc 1 clock 83368421

Quoted 7 lines

Quoted 1 line
Is this the expected behavior on receive?
No, it should go into error passive if one of the error counters have >
127. Maybe this is an error onthe vf610, maybe it's a general flexcan problem.
Marc

--
Stefan

Marc Kleine-Budde

maintainer

2014-08-05 09:52 UTC #18 lore raw

Re: [PATCH v3 4/4] can: flexcan: add vf610 support for FlexCAN

Quoted 56 lines · Stefan Agner

Am 2014-08-04 16:27, schrieb Marc Kleine-Budde:
Quoted 47 lines · Stefan Agner
[...]
Quoted 25 lines
Quoted 25 lines
Thanks for the test, so far looks promising :) With this setup the other CAN node repeats the CAN frame until it's ACKed. Because there is no node with a compatible bitrate, there is no ACking CAN node.
Can you add a third CAN node to the network. The second and third node should use the same bitrate, while your vf610 uses a different one. With the new setup it should take more than one frame until the vf610 goes into error warning and even more frames to error passive. This way we can see it the error warning interrupt is connected or not. The error counters should increase with each "wrong" bitrate frame it sees, you can check with:
ip -details link show can0
The output looks like this:
Quoted 3 lines
4: can0: <NOARP,UP,LOWER_UP,ECHO> mtu 16 qdisc pfifo_fast state UNKNOWN mode DEFAULT qlen 10
link/can
can state ERROR-ACTIVE (berr-counter tx 0 rx 0) restart-ms 0
                              ^^^^^^^^^^^^^^^^^^^^^^
Quoted 4 lines
    bitrate 1000000 sample-point 0.750
    tq 125 prop-seg 2 phase-seg1 3 phase-seg2 2 sjw 1
    sja1000: tseg1 1..16 tseg2 1..8 sjw 1..4 brp 1..64 brp-inc 1
    clock 8000000
Quoted 7 lines
Quoted 2 lines
When one of the berr-counter crosses 96 (and stays below 128) a warning interrupt should be generated.
Ok, created this setup, could successfully communicate with all three nodes. I then set the Vybrid to half of the bitrate. When I send a frame from Vybrid, the berr-counter tx immediately ends up at 128 and the device is in ERROR-PASSIVE:
This is expected.
Quoted 9 lines
root at colibri-vf:~# ip -details link show can1
3: can1: <NOARP,UP,LOWER_UP,ECHO> mtu 16 qdisc pfifo_fast state UNKNOWN mode DEFAULT group default qlen 10
link/can promiscuity 0
can state ERROR-ACTIVE (berr-counter tx 0 rx 0) restart-ms 0 bitrate 124990 sample-point 0.739
tq 347 prop-seg 8 phase-seg1 8 phase-seg2 6 sjw 1
flexcan: tseg1 4..16 tseg2 2..8 sjw 1..4 brp 1..256 brp-inc 1 clock 83368421
Quoted 7 lines
            ^^^^^^^^
BTW: the can core has a really weird clock rate, have a look at the datasheet if you manage to route a 24 MHz clock (or another multiple of 8MHz) to the flexcan core. I had a quick glance at the datasheet, if I understand it correctly the Fast OSC clock runs with 24 MHz.

Quoted 4 lines

This pinmux is actually part of the IPs CTRL register (see CLKSRC). Currently this is set unconditionally to peripheral clock, which is on my device 83.3 MHz (500MHz/6). This would be a bit bigger change. Just thinking how to implement this.

Sigh! I've missed the fact, that this bit is _inside_ the CAN core (again). On the mx53 and imx6 this bit was obsolete and the clock was selected outside of the CAN core.

Quoted 3 lines

Maybe we have to reference a third clock
"osc" and a device tree property fsl,can-clock-osc which one can choose between "osc" and "per" what do you think?

Yes, but that's a different patch. I thought it would be as easy as on the mx53, where you just had to reconfigure the clock tree.

Quoted 20 lines

Quoted 20 lines
Quoted 19 lines
root at colibri-vf:~# cansend can1 1F334455#1122334455667788 interface = can1, family = 29, type = 3, proto = 1 root at colibri-vf:~# [ 818.886664] flexcan_irq, esr=00062242
[  818.890365] flexcan_irq, ctrl=1c3dac57
root at colibri-vf:~# ip -details link show can1
3: can1: <NOARP,UP,LOWER_UP,ECHO> mtu 16 qdisc pfifo_fast state UNKNOWN mode DEFAULT group default qlen 10
link/can promiscuity 0
can state ERROR-PASSIVE (berr-counter tx 128 rx 0) restart-ms 0 bitrate 124990 sample-point 0.739
tq 347 prop-seg 8 phase-seg1 8 phase-seg2 6 sjw 1
flexcan: tseg1 4..16 tseg2 2..8 sjw 1..4 brp 1..256 brp-inc 1 clock 83368421
When I send the frames from another device on the bus, I can see the rx count incrementing by one on each frame I send. As you expected, the device changes to ERROR-WARNING when crossing the 96 frame boundary:

Quoted 6 lines

Quoted 2 lines
This is correct
Just found out when using too high bitrate (500000 vs 125000), the error counter immediately goes up to 128 (or even beyond) and ends up in ERROR-PASSIVE:

Maybe there is a off-by-one error in the flexcan core, so that a rx error of 127 doesn't trigger an error passive interrupt.

Quoted 11 lines

# ip -details link show can1
[  292.164820] flexcan_get_berr_counter, esr=00000000
[  292.169715] flexcan_get_berr_counter, esr=00040190
3: can1: <NOARP,UP,LOWER_UP,ECHO> mtu 16 qdisc pfifo_fast state UNKNOWN
mode DEFAULT group default qlen 10
    link/can  promiscuity 0
    can state ERROR-PASSIVE (berr-counter tx 0 rx 135) restart-ms 0
    bitrate 298811 sample-point 0.777
    tq 371 prop-seg 3 phase-seg1 3 phase-seg2 2 sjw 1
    flexcan: tseg1 4..16 tseg2 2..8 sjw 1..4 brp 1..256 brp-inc 1
    clock 83368421

[...]

Quoted 60 lines

Quoted 5 lines
Quoted 2 lines
However, once reaching 128, I don't get another interrupt and the device stays in ERROR-WARNING:
The contents of the esr reg would be interesting, especially the FLT_CONF part.
root at vybridvf61-v11:~# [ 222.221651] flexcan_irq, esr=0005050a
[  222.225349] flexcan_irq, ctrl=1c3dac57
ip -details link show can1
[  223.791082] flexcan_get_berr_counter, esr=00000000
[  223.796246] flexcan_get_berr_counter, esr=00040180
3: can1: <NOARP,UP,LOWER_UP,ECHO> mtu 16 qdisc pfifo_fast state UNKNOWN mode DEFAULT group default qlen
10
link/can promiscuity 0
can state ERROR-WARNING (berr-counter tx 0 rx 96) restart-ms 0 bitrate 124990 sample-point 0.739
tq 347 prop-seg 8 phase-seg1 8 phase-seg2 6 sjw 1
flexcan: tseg1 4..16 tseg2 2..8 sjw 1..4 brp 1..256 brp-inc 1 clock 83368421
root at vybridvf61-v11:~# ip -details link show can1
[  243.571175] flexcan_get_berr_counter, esr=00000000
[  243.576343] flexcan_get_berr_counter, esr=00040582
3: can1: <NOARP,UP,LOWER_UP,ECHO> mtu 16 qdisc pfifo_fast state UNKNOWN mode DEFAULT group default qlen
10
link/can promiscuity 0
can state ERROR-WARNING (berr-counter tx 0 rx 104) restart-ms 0 bitrate 124990 sample-point 0.739
tq 347 prop-seg 8 phase-seg1 8 phase-seg2 6 sjw 1
flexcan: tseg1 4..16 tseg2 2..8 sjw 1..4 brp 1..256 brp-inc 1 clock 83368421
...
root at vybridvf61-v11:~# ip -details link show can1
[  299.831192] flexcan_get_berr_counter, esr=00000000
[  299.836358] flexcan_get_berr_counter, esr=00040582
3: can1: <NOARP,UP,LOWER_UP,ECHO> mtu 16 qdisc pfifo_fast state UNKNOWN mode DEFAULT group default qlen 10
link/can promiscuity 0
can state ERROR-WARNING (berr-counter tx 0 rx 126) restart-ms 0 bitrate 124990 sample-point 0.739
tq 347 prop-seg 8 phase-seg1 8 phase-seg2 6 sjw 1
flexcan: tseg1 4..16 tseg2 2..8 sjw 1..4 brp 1..256 brp-inc 1 clock 83368421
root at vybridvf61-v11:~# ip -details link show can1
[  302.411025] flexcan_get_berr_counter, esr=00000000
[  302.416195] flexcan_get_berr_counter, esr=00040592
3: can1: <NOARP,UP,LOWER_UP,ECHO> mtu 16 qdisc pfifo_fast state UNKNOWN mode DEFAULT group default qlen 10
link/can promiscuity 0
can state ERROR-WARNING (berr-counter tx 0 rx 128) restart-ms 0 bitrate 124990 sample-point 0.739
tq 347 prop-seg 8 phase-seg1 8 phase-seg2 6 sjw 1
flexcan: tseg1 4..16 tseg2 2..8 sjw 1..4 brp 1..256 brp-inc 1 clock 83368421

Quoted 4 lines

The FLTCONF is in Error Passive, however the stack did not received that information. I still have the printk in the interrupt, however I did not get an interrupt here (while I get one when it switched to ERROR-WARNING... But it looks like the ERRINT is still pending...

According to the datasheet the ERRINT indicates a bit error (bit 10...15 is set), not the error passive state.

Marc

Signature · 12 lines

Pengutronix e.K.                  | Marc Kleine-Budde           |
Industrial Linux Solutions        | Phone: +49-231-2826-924     |
Vertretung West/Dortmund          | Fax:   +49-5121-206917-5555 |
Amtsgericht Hildesheim, HRA 2686  | http://www.pengutronix.de   |

-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 242 bytes
Desc: OpenPGP digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20140805/8221a4b2/attachment-0001.sig>

Stefan Agner

author reviewer

2014-08-05 12:38 UTC #19 lore raw

Re: [PATCH v3 4/4] can: flexcan: add vf610 support for FlexCAN

Am 2014-08-05 11:52, schrieb Marc Kleine-Budde:

Quoted 66 lines · Stefan Agner

Quoted 56 lines
Am 2014-08-04 16:27, schrieb Marc Kleine-Budde:
Quoted 47 lines · Stefan Agner
[...]
Quoted 25 lines
Quoted 25 lines
Thanks for the test, so far looks promising :) With this setup the other CAN node repeats the CAN frame until it's ACKed. Because there is no node with a compatible bitrate, there is no ACking CAN node.
Can you add a third CAN node to the network. The second and third node should use the same bitrate, while your vf610 uses a different one. With the new setup it should take more than one frame until the vf610 goes into error warning and even more frames to error passive. This way we can see it the error warning interrupt is connected or not. The error counters should increase with each "wrong" bitrate frame it sees, you can check with:
ip -details link show can0
The output looks like this:
Quoted 3 lines
4: can0: <NOARP,UP,LOWER_UP,ECHO> mtu 16 qdisc pfifo_fast state UNKNOWN mode DEFAULT qlen 10
link/can
can state ERROR-ACTIVE (berr-counter tx 0 rx 0) restart-ms 0
                              ^^^^^^^^^^^^^^^^^^^^^^
Quoted 4 lines
    bitrate 1000000 sample-point 0.750
    tq 125 prop-seg 2 phase-seg1 3 phase-seg2 2 sjw 1
    sja1000: tseg1 1..16 tseg2 1..8 sjw 1..4 brp 1..64 brp-inc 1
    clock 8000000
Quoted 7 lines
Quoted 2 lines
When one of the berr-counter crosses 96 (and stays below 128) a warning interrupt should be generated.
Ok, created this setup, could successfully communicate with all three nodes. I then set the Vybrid to half of the bitrate. When I send a frame from Vybrid, the berr-counter tx immediately ends up at 128 and the device is in ERROR-PASSIVE:
This is expected.
Quoted 9 lines
root at colibri-vf:~# ip -details link show can1
3: can1: <NOARP,UP,LOWER_UP,ECHO> mtu 16 qdisc pfifo_fast state UNKNOWN mode DEFAULT group default qlen 10
link/can promiscuity 0
can state ERROR-ACTIVE (berr-counter tx 0 rx 0) restart-ms 0 bitrate 124990 sample-point 0.739
tq 347 prop-seg 8 phase-seg1 8 phase-seg2 6 sjw 1
flexcan: tseg1 4..16 tseg2 2..8 sjw 1..4 brp 1..256 brp-inc 1 clock 83368421
Quoted 7 lines
            ^^^^^^^^
BTW: the can core has a really weird clock rate, have a look at the datasheet if you manage to route a 24 MHz clock (or another multiple of 8MHz) to the flexcan core. I had a quick glance at the datasheet, if I understand it correctly the Fast OSC clock runs with 24 MHz.
Quoted 4 lines
This pinmux is actually part of the IPs CTRL register (see CLKSRC). Currently this is set unconditionally to peripheral clock, which is on my device 83.3 MHz (500MHz/6). This would be a bit bigger change. Just thinking how to implement this.
Sigh! I've missed the fact, that this bit is _inside_ the CAN core (again). On the mx53 and imx6 this bit was obsolete and the clock was selected outside of the CAN core.

Quoted 7 lines

Quoted 3 lines
Maybe we have to reference a third clock
"osc" and a device tree property fsl,can-clock-osc which one can choose between "osc" and "per" what do you think?
Yes, but that's a different patch. I thought it would be as easy as on the mx53, where you just had to reconfigure the clock tree.

Agreed.

Quoted 109 lines

Quoted 20 lines
Quoted 20 lines
Quoted 19 lines
root at colibri-vf:~# cansend can1 1F334455#1122334455667788 interface = can1, family = 29, type = 3, proto = 1 root at colibri-vf:~# [ 818.886664] flexcan_irq, esr=00062242
[  818.890365] flexcan_irq, ctrl=1c3dac57
root at colibri-vf:~# ip -details link show can1
3: can1: <NOARP,UP,LOWER_UP,ECHO> mtu 16 qdisc pfifo_fast state UNKNOWN mode DEFAULT group default qlen 10
link/can promiscuity 0
can state ERROR-PASSIVE (berr-counter tx 128 rx 0) restart-ms 0 bitrate 124990 sample-point 0.739
tq 347 prop-seg 8 phase-seg1 8 phase-seg2 6 sjw 1
flexcan: tseg1 4..16 tseg2 2..8 sjw 1..4 brp 1..256 brp-inc 1 clock 83368421
When I send the frames from another device on the bus, I can see the rx count incrementing by one on each frame I send. As you expected, the device changes to ERROR-WARNING when crossing the 96 frame boundary:
Quoted 6 lines
Quoted 2 lines
This is correct
Just found out when using too high bitrate (500000 vs 125000), the error counter immediately goes up to 128 (or even beyond) and ends up in ERROR-PASSIVE:
Maybe there is a off-by-one error in the flexcan core, so that a rx error of 127 doesn't trigger an error passive interrupt.
Quoted 11 lines
# ip -details link show can1
[  292.164820] flexcan_get_berr_counter, esr=00000000
[  292.169715] flexcan_get_berr_counter, esr=00040190
3: can1: <NOARP,UP,LOWER_UP,ECHO> mtu 16 qdisc pfifo_fast state UNKNOWN
mode DEFAULT group default qlen 10
    link/can  promiscuity 0
    can state ERROR-PASSIVE (berr-counter tx 0 rx 135) restart-ms 0
    bitrate 298811 sample-point 0.777
    tq 371 prop-seg 3 phase-seg1 3 phase-seg2 2 sjw 1
    flexcan: tseg1 4..16 tseg2 2..8 sjw 1..4 brp 1..256 brp-inc 1
    clock 83368421
[...]
Quoted 60 lines
Quoted 5 lines
Quoted 2 lines
However, once reaching 128, I don't get another interrupt and the device stays in ERROR-WARNING:
The contents of the esr reg would be interesting, especially the FLT_CONF part.
root at vybridvf61-v11:~# [ 222.221651] flexcan_irq, esr=0005050a
[  222.225349] flexcan_irq, ctrl=1c3dac57
ip -details link show can1
[  223.791082] flexcan_get_berr_counter, esr=00000000
[  223.796246] flexcan_get_berr_counter, esr=00040180
3: can1: <NOARP,UP,LOWER_UP,ECHO> mtu 16 qdisc pfifo_fast state UNKNOWN mode DEFAULT group default qlen
10
link/can promiscuity 0
can state ERROR-WARNING (berr-counter tx 0 rx 96) restart-ms 0 bitrate 124990 sample-point 0.739
tq 347 prop-seg 8 phase-seg1 8 phase-seg2 6 sjw 1
flexcan: tseg1 4..16 tseg2 2..8 sjw 1..4 brp 1..256 brp-inc 1 clock 83368421
root at vybridvf61-v11:~# ip -details link show can1
[  243.571175] flexcan_get_berr_counter, esr=00000000
[  243.576343] flexcan_get_berr_counter, esr=00040582
3: can1: <NOARP,UP,LOWER_UP,ECHO> mtu 16 qdisc pfifo_fast state UNKNOWN mode DEFAULT group default qlen
10
link/can promiscuity 0
can state ERROR-WARNING (berr-counter tx 0 rx 104) restart-ms 0 bitrate 124990 sample-point 0.739
tq 347 prop-seg 8 phase-seg1 8 phase-seg2 6 sjw 1
flexcan: tseg1 4..16 tseg2 2..8 sjw 1..4 brp 1..256 brp-inc 1 clock 83368421
...
root at vybridvf61-v11:~# ip -details link show can1
[  299.831192] flexcan_get_berr_counter, esr=00000000
[  299.836358] flexcan_get_berr_counter, esr=00040582
3: can1: <NOARP,UP,LOWER_UP,ECHO> mtu 16 qdisc pfifo_fast state UNKNOWN mode DEFAULT group default qlen 10
link/can promiscuity 0
can state ERROR-WARNING (berr-counter tx 0 rx 126) restart-ms 0 bitrate 124990 sample-point 0.739
tq 347 prop-seg 8 phase-seg1 8 phase-seg2 6 sjw 1
flexcan: tseg1 4..16 tseg2 2..8 sjw 1..4 brp 1..256 brp-inc 1 clock 83368421
root at vybridvf61-v11:~# ip -details link show can1
[  302.411025] flexcan_get_berr_counter, esr=00000000
[  302.416195] flexcan_get_berr_counter, esr=00040592
3: can1: <NOARP,UP,LOWER_UP,ECHO> mtu 16 qdisc pfifo_fast state UNKNOWN mode DEFAULT group default qlen 10
link/can promiscuity 0
can state ERROR-WARNING (berr-counter tx 0 rx 128) restart-ms 0 bitrate 124990 sample-point 0.739
tq 347 prop-seg 8 phase-seg1 8 phase-seg2 6 sjw 1
flexcan: tseg1 4..16 tseg2 2..8 sjw 1..4 brp 1..256 brp-inc 1 clock 83368421
Quoted 4 lines
The FLTCONF is in Error Passive, however the stack did not received that information. I still have the printk in the interrupt, however I did not get an interrupt here (while I get one when it switched to ERROR-WARNING... But it looks like the ERRINT is still pending...

Quoted 4 lines

According to the datasheet the ERRINT indicates a bit error (bit 10...15 is set), not the error passive state.
Marc

True, but fact is, I don't get a interrupt when the system switches from ERROR-WARNING to ERROR-PASSIVE state. However, when I set berr-reporting on, I get an interrupt (probably because of a change of bit 10...15), but the state change is recognized:

ip -details link show can1

[ 2303.571656] flexcan_get_berr_counter, esr=00000000
[ 2303.576832] flexcan_get_berr_counter, esr=00040180

3: can1: <NOARP,UP,LOWER_UP,ECHO> mtu 16 qdisc pfifo_fast state UNKNOWN mode DEFAULT group default qlen 10
link/can promiscuity 0
can <BERR-REPORTING> state ERROR-WARNING (berr-counter tx 0 rx 127)
restart-ms 0

    bitrate 124990 sample-point 0.739 
    tq 347 prop-seg 8 phase-seg1 8 phase-seg2 6 sjw 1
    flexcan: tseg1 4..16 tseg2 2..8 sjw 1..4 brp 1..256 brp-inc 1
    clock 83368421
root at vybridvf61-v11:~# [ 2307.023789] flexcan_irq, esr=0004051a
[ 2307.027490] flexcan_irq, ctrl=1c3dec57
ip -details link show can1
[ 2309.081840] flexcan_get_berr_counter, esr=00000000
[ 2309.087016] flexcan_get_berr_counter, esr=00040190

3: can1: <NOARP,UP,LOWER_UP,ECHO> mtu 16 qdisc pfifo_fast state UNKNOWN mode DEFAULT group default qlen 10
link/can promiscuity 0
can <BERR-REPORTING> state ERROR-PASSIVE (berr-counter tx 0 rx 128)
restart-ms 0

    bitrate 124990 sample-point 0.739 
    tq 347 prop-seg 8 phase-seg1 8 phase-seg2 6 sjw 1
    flexcan: tseg1 4..16 tseg2 2..8 sjw 1..4 brp 1..256 brp-inc 1
    clock 83368421

It looks like, the FLTCONF state change itself doesn't lead to a interrupt when the state changes to ERROR-PASSIVE. IMHO, this is also not explicitly stated in the Vybrid RM (46.3.8).

What is the solution here? Force enabling ERR interrupt? The FLEXCAN_HAS_BROKEN_ERR_STATE flag would be appropriate, however, this was meant to work around the missing WRN_INT, which seems not to be the case here...

--
Stefan

Marc Kleine-Budde

maintainer

2014-08-14 10:38 UTC #20 lore raw

Re: [PATCH v3 4/4] can: flexcan: add vf610 support for FlexCAN

In reply to Stefan Agner

Quoted 184 lines · Stefan Agner

Am 2014-08-04 16:27, schrieb Marc Kleine-Budde:
Quoted 47 lines · Stefan Agner
[...]
Quoted 25 lines
Quoted 25 lines
Thanks for the test, so far looks promising :) With this setup the other CAN node repeats the CAN frame until it's ACKed. Because there is no node with a compatible bitrate, there is no ACking CAN node.
Can you add a third CAN node to the network. The second and third node should use the same bitrate, while your vf610 uses a different one. With the new setup it should take more than one frame until the vf610 goes into error warning and even more frames to error passive. This way we can see it the error warning interrupt is connected or not. The error counters should increase with each "wrong" bitrate frame it sees, you can check with:
ip -details link show can0
The output looks like this:
Quoted 3 lines
4: can0: <NOARP,UP,LOWER_UP,ECHO> mtu 16 qdisc pfifo_fast state UNKNOWN mode DEFAULT qlen 10
link/can
can state ERROR-ACTIVE (berr-counter tx 0 rx 0) restart-ms 0
                              ^^^^^^^^^^^^^^^^^^^^^^
Quoted 4 lines
    bitrate 1000000 sample-point 0.750
    tq 125 prop-seg 2 phase-seg1 3 phase-seg2 2 sjw 1
    sja1000: tseg1 1..16 tseg2 1..8 sjw 1..4 brp 1..64 brp-inc 1
    clock 8000000
Quoted 7 lines
Quoted 2 lines
When one of the berr-counter crosses 96 (and stays below 128) a warning interrupt should be generated.
Ok, created this setup, could successfully communicate with all three nodes. I then set the Vybrid to half of the bitrate. When I send a frame from Vybrid, the berr-counter tx immediately ends up at 128 and the device is in ERROR-PASSIVE:
This is expected.
Quoted 9 lines
root at colibri-vf:~# ip -details link show can1
3: can1: <NOARP,UP,LOWER_UP,ECHO> mtu 16 qdisc pfifo_fast state UNKNOWN mode DEFAULT group default qlen 10
link/can promiscuity 0
can state ERROR-ACTIVE (berr-counter tx 0 rx 0) restart-ms 0 bitrate 124990 sample-point 0.739
tq 347 prop-seg 8 phase-seg1 8 phase-seg2 6 sjw 1
flexcan: tseg1 4..16 tseg2 2..8 sjw 1..4 brp 1..256 brp-inc 1 clock 83368421
Quoted 7 lines
            ^^^^^^^^
BTW: the can core has a really weird clock rate, have a look at the datasheet if you manage to route a 24 MHz clock (or another multiple of 8MHz) to the flexcan core. I had a quick glance at the datasheet, if I understand it correctly the Fast OSC clock runs with 24 MHz.
This pinmux is actually part of the IPs CTRL register (see CLKSRC). Currently this is set unconditionally to peripheral clock, which is on my device 83.3 MHz (500MHz/6). This would be a bit bigger change. Just thinking how to implement this. Maybe we have to reference a third clock "osc" and a device tree property fsl,can-clock-osc which one can choose between "osc" and "per" what do you think?
Quoted 16 lines
Quoted 16 lines
root at colibri-vf:~# cansend can1 1F334455#1122334455667788 interface = can1, family = 29, type = 3, proto = 1 root at colibri-vf:~# [ 818.886664] flexcan_irq, esr=00062242
[  818.890365] flexcan_irq, ctrl=1c3dac57
root at colibri-vf:~# ip -details link show can1
3: can1: <NOARP,UP,LOWER_UP,ECHO> mtu 16 qdisc pfifo_fast state UNKNOWN mode DEFAULT group default qlen 10
link/can promiscuity 0
can state ERROR-PASSIVE (berr-counter tx 128 rx 0) restart-ms 0 bitrate 124990 sample-point 0.739
tq 347 prop-seg 8 phase-seg1 8 phase-seg2 6 sjw 1
flexcan: tseg1 4..16 tseg2 2..8 sjw 1..4 brp 1..256 brp-inc 1 clock 83368421
Quoted 6 lines
Quoted 3 lines
When I send the frames from another device on the bus, I can see the rx count incrementing by one on each frame I send. As you expected, the device changes to ERROR-WARNING when crossing the 96 frame boundary:
This is correct
Just found out when using too high bitrate (500000 vs 125000), the error counter immediately goes up to 128 (or even beyond) and ends up in ERROR-PASSIVE:
# ip -details link show can1
[  292.164820] flexcan_get_berr_counter, esr=00000000
[  292.169715] flexcan_get_berr_counter, esr=00040190
3: can1: <NOARP,UP,LOWER_UP,ECHO> mtu 16 qdisc pfifo_fast state UNKNOWN
mode DEFAULT group default qlen 10
    link/can  promiscuity 0
    can state ERROR-PASSIVE (berr-counter tx 0 rx 135) restart-ms 0
    bitrate 298811 sample-point 0.777
    tq 371 prop-seg 3 phase-seg1 3 phase-seg2 2 sjw 1
    flexcan: tseg1 4..16 tseg2 2..8 sjw 1..4 brp 1..256 brp-inc 1
    clock 83368421
Quoted 21 lines
Quoted 20 lines
root at colibri-vf:~# ip -details link show can1
3: can1: <NOARP,UP,LOWER_UP,ECHO> mtu 16 qdisc pfifo_fast state UNKNOWN mode DEFAULT group default qlen 10
link/can promiscuity 0
can state ERROR-ACTIVE (berr-counter tx 0 rx 92) restart-ms 0 bitrate 124990 sample-point 0.739
tq 347 prop-seg 8 phase-seg1 8 phase-seg2 6 sjw 1
flexcan: tseg1 4..16 tseg2 2..8 sjw 1..4 brp 1..256 brp-inc 1 clock 83368421
root at colibri-vf:~# [ 448.331150] flexcan_irq, esr=0005050a
[  448.334851] flexcan_irq, ctrl=1c3dac57
ip -details link show can1
3: can1: <NOARP,UP,LOWER_UP,ECHO> mtu 16 qdisc pfifo_fast state UNKNOWN mode DEFAULT group default qlen 10
link/can promiscuity 0
can state ERROR-WARNING (berr-counter tx 0 rx 102) restart-ms 0 bitrate 124990 sample-point 0.739
tq 347 prop-seg 8 phase-seg1 8 phase-seg2 6 sjw 1
flexcan: tseg1 4..16 tseg2 2..8 sjw 1..4 brp 1..256 brp-inc 1 clock 83368421
Quoted 6 lines
Quoted 2 lines
However, once reaching 128, I don't get another interrupt and the device stays in ERROR-WARNING:
The contents of the esr reg would be interesting, especially the FLT_CONF part.
root at vybridvf61-v11:~# [ 222.221651] flexcan_irq, esr=0005050a
[  222.225349] flexcan_irq, ctrl=1c3dac57
ip -details link show can1
[  223.791082] flexcan_get_berr_counter, esr=00000000
[  223.796246] flexcan_get_berr_counter, esr=00040180
3: can1: <NOARP,UP,LOWER_UP,ECHO> mtu 16 qdisc pfifo_fast state UNKNOWN mode DEFAULT group default qlen
10
link/can promiscuity 0
can state ERROR-WARNING (berr-counter tx 0 rx 96) restart-ms 0 bitrate 124990 sample-point 0.739
tq 347 prop-seg 8 phase-seg1 8 phase-seg2 6 sjw 1
flexcan: tseg1 4..16 tseg2 2..8 sjw 1..4 brp 1..256 brp-inc 1 clock 83368421
root at vybridvf61-v11:~# ip -details link show can1
[  243.571175] flexcan_get_berr_counter, esr=00000000
[  243.576343] flexcan_get_berr_counter, esr=00040582
3: can1: <NOARP,UP,LOWER_UP,ECHO> mtu 16 qdisc pfifo_fast state UNKNOWN mode DEFAULT group default qlen
10
link/can promiscuity 0
can state ERROR-WARNING (berr-counter tx 0 rx 104) restart-ms 0 bitrate 124990 sample-point 0.739
tq 347 prop-seg 8 phase-seg1 8 phase-seg2 6 sjw 1
flexcan: tseg1 4..16 tseg2 2..8 sjw 1..4 brp 1..256 brp-inc 1 clock 83368421
...
root at vybridvf61-v11:~# ip -details link show can1
[  299.831192] flexcan_get_berr_counter, esr=00000000
[  299.836358] flexcan_get_berr_counter, esr=00040582
3: can1: <NOARP,UP,LOWER_UP,ECHO> mtu 16 qdisc pfifo_fast state UNKNOWN mode DEFAULT group default qlen 10
link/can promiscuity 0
can state ERROR-WARNING (berr-counter tx 0 rx 126) restart-ms 0 bitrate 124990 sample-point 0.739
tq 347 prop-seg 8 phase-seg1 8 phase-seg2 6 sjw 1
flexcan: tseg1 4..16 tseg2 2..8 sjw 1..4 brp 1..256 brp-inc 1 clock 83368421
root at vybridvf61-v11:~# ip -details link show can1
[  302.411025] flexcan_get_berr_counter, esr=00000000
[  302.416195] flexcan_get_berr_counter, esr=00040592
3: can1: <NOARP,UP,LOWER_UP,ECHO> mtu 16 qdisc pfifo_fast state UNKNOWN mode DEFAULT group default qlen 10
link/can promiscuity 0
can state ERROR-WARNING (berr-counter tx 0 rx 128) restart-ms 0 bitrate 124990 sample-point 0.739
tq 347 prop-seg 8 phase-seg1 8 phase-seg2 6 sjw 1
flexcan: tseg1 4..16 tseg2 2..8 sjw 1..4 brp 1..256 brp-inc 1 clock 83368421

Quoted 4 lines

The FLTCONF is in Error Passive, however the stack did not received that information. I still have the printk in the interrupt, however I did not get an interrupt here (while I get one when it switched to ERROR-WARNING... But it looks like the ERRINT is still pending...

Can you apply Alexander Stein's "[PATCH 2/4] can: flexcan: Detect error passive state change" and recheck?

Marc

Signature · 12 lines

Pengutronix e.K.                  | Marc Kleine-Budde           |
Industrial Linux Solutions        | Phone: +49-231-2826-924     |
Vertretung West/Dortmund          | Fax:   +49-5121-206917-5555 |
Amtsgericht Hildesheim, HRA 2686  | http://www.pengutronix.de   |

-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 181 bytes
Desc: OpenPGP digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20140814/a558e7b0/attachment-0001.sig>

Marc Kleine-Budde

maintainer

2014-07-28 16:29 UTC #21 lore raw

Re: [PATCH v3 4/4] can: flexcan: add vf610 support for FlexCAN

In reply to Stefan Agner

Quoted 4 lines · Stefan Agner

Quoted 4 lines
Quoted 1 line
Ping. Anything open/to do from my side?
Please keep the printing of esr and ctrl in the interrupt handler, add a #define DEBUG in the driver, but do not change anything else. Then:

                                    ^^^^^^^^^^^^^^^^^^^^^^^^^^^

drivers/net/can/flexcan.c line 22

Quoted 10 lines

drivers/net/can/flexcan.c +1 -0

index 1c31a5d..fe8b81c 100644
@@ -19,6 +19,7 @@
  *
  */
 
+#define DEBUG

keep

drivers/net/can/flexcan.c static irqreturn_t flexcan_irq(int irq, void · line 750

Quoted 11 lines

drivers/net/can/flexcan.c +3 -0

 #include <linux/netdevice.h>
 #include <linux/can.h>
 #include <linux/can/dev.h>

@@ -743,6 +744,9 @@ static irqreturn_t flexcan_irq(int irq, void
 *dev_id)
 
        reg_iflag1 = flexcan_read(&regs->iflag1);
        reg_esr = flexcan_read(&regs->esr);
+
+       printk("flexcan_irq, esr=%08x\n", reg_esr);
+       printk("flexcan_irq, ctrl=%08x\n", flexcan_read(&regs->ctrl));

keep

Quoted 17 lines

drivers/net/can/flexcan.c +0 -0

        /* ACK all bus error and state change IRQ sources */
        if (reg_esr & FLEXCAN_ESR_ALL_INT)

flexcan_write(reg_esr & FLEXCAN_ESR_ALL_INT,
&regs->esr);

drivers/net/can/flexcan.c +2 -2

@@ -885,8 +889,8 @@ static int flexcan_chip_start(struct net_device
 *dev)
         */
        reg_ctrl = flexcan_read(&regs->ctrl);
        reg_ctrl &= ~FLEXCAN_CTRL_TSYN;
-       reg_ctrl |= FLEXCAN_CTRL_BOFF_REC | FLEXCAN_CTRL_LBUF |
-               FLEXCAN_CTRL_ERR_STATE;
+       reg_ctrl |= FLEXCAN_CTRL_BOFF_REC | FLEXCAN_CTRL_LBUF;// |
+               //FLEXCAN_CTRL_ERR_STATE;
        /*
         * enable the "error interrupt" (FLEXCAN_CTRL_ERR_MSK),

* on most Flexcan cores, too. Otherwise we don't get

Quoted 2 lines

I'm not sure whether you really want to keep the FLEXCAN_CTRL_ERR_STATE commented out...

No, please remove this change and redo the test.

Marc

Signature · 4 lines

Pengutronix e.K.                  | Marc Kleine-Budde           |
Industrial Linux Solutions        | Phone: +49-231-2826-924     |
Vertretung West/Dortmund          | Fax:   +49-5121-206917-5555 |
Amtsgericht Hildesheim, HRA 2686  | http://www.pengutronix.de   |

Marc Kleine-Budde

maintainer

2014-07-28 16:31 UTC #22 lore raw

Re: [PATCH v3 4/4] can: flexcan: add vf610 support for FlexCAN

In reply to Stefan Agner

On 07/28/2014 06:20 PM, Stefan Agner wrote:
[...]

Quoted 9 lines

However, I got once this Kernel panic after I reconfigured to normal mode. But I could not reproduce this.

[  461.954394] flexcan_irq, esr=00059d82
[  461.958093] flexcan_irq, ctrl=17092051
[  461.961873] ------------[ cut here ]------------
[  461.966536] WARNING: CPU: 0 PID: 0 at kernel/locking/mutex.c:826
mutex_trylock+0x1b0/0x208()
[  461.974982] DEBUG_LOCKS_WARN_ON(in_interrupt())

Please use this updated version of your patch:

Marc

---

Quoted 1 line

From b6b8ae7cdb04f1a3b9d3a6dd83f8146bfaf48553 Mon Sep 17 00:00:00 2001

From: Stefan Agner <[email protected]>
Date: Tue, 15 Jul 2014 14:56:20 +0200
Subject: [PATCH] can: flexcan: flexcan_get_berr_counter(): switch on clocks
before accessing ecr register

The funcion flexcan_get_berr_counter() may be called from userspace even if the interface is down, this the clocks are disabled. This patch switches on the clocks before accessing the ecr register.

Reported-by Ashutosh Singh <[email protected]>

Signed-off-by Stefan Agner <[email protected]>

Signed-off-by Marc Kleine-Budde <[email protected]>

---
 drivers/net/can/flexcan.c | 30 +++++++++++++++++++++++++++---
 1 file changed, 27 insertions(+), 3 deletions(-)

drivers/net/can/flexcan.c +27 -3

index f425ec2..6bfe24a 100644
@@ -378,8 +378,9 @@ static int flexcan_chip_softreset(struct flexcan_priv *priv)
 	return 0;
 }
 
-static int flexcan_get_berr_counter(const struct net_device *dev,
-				    struct can_berr_counter *bec)
+
+static int __flexcan_get_berr_counter(const struct net_device *dev,
+				      struct can_berr_counter *bec)
 {
 	const struct flexcan_priv *priv = netdev_priv(dev);
 	struct flexcan_regs __iomem *regs = priv->base;

@@ -391,6 +392,29 @@ static int flexcan_get_berr_counter(const struct net_device *dev,
 	return 0;
 }
 
+static int flexcan_get_berr_counter(const struct net_device *dev,
+				    struct can_berr_counter *bec)
+{
+	const struct flexcan_priv *priv = netdev_priv(dev);
+	int err;
+
+	err = clk_prepare_enable(priv->clk_ipg);
+	if (err)
+		return err;
+
+	err = clk_prepare_enable(priv->clk_per);
+	if (err)
+		goto out_disable_ipg;
+
+	err = __flexcan_get_berr_counter(dev, bec);
+
+	clk_disable_unprepare(priv->clk_per);
+ out_disable_ipg:
+	clk_disable_unprepare(priv->clk_ipg);
+
+	return err;
+}
+
 static int flexcan_start_xmit(struct sk_buff *skb, struct net_device *dev)
 {
 	const struct flexcan_priv *priv = netdev_priv(dev);

@@ -503,7 +527,7 @@ static void do_state(struct net_device *dev,
 	struct flexcan_priv *priv = netdev_priv(dev);
 	struct can_berr_counter bec;
 
-	flexcan_get_berr_counter(dev, &bec);
+	__flexcan_get_berr_counter(dev, &bec);
 
 	switch (priv->can.state) {
 	case CAN_STATE_ERROR_ACTIVE:

Signature · 15 lines

2.0.1

-- 
Pengutronix e.K.                  | Marc Kleine-Budde           |
Industrial Linux Solutions        | Phone: +49-231-2826-924     |
Vertretung West/Dortmund          | Fax:   +49-5121-206917-5555 |
Amtsgericht Hildesheim, HRA 2686  | http://www.pengutronix.de   |

-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 242 bytes
Desc: OpenPGP digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20140728/a980ea01/attachment.sig>

Stefan Agner

author reviewer

2014-07-28 16:30 UTC #23 lore raw

Re: [PATCH v3 4/4] can: flexcan: add vf610 support for FlexCAN

In reply to Marc Kleine-Budde

Am 2014-07-25 15:33, schrieb Marc Kleine-Budde:

Quoted 40 lines · Stefan Agner

Quoted 39 lines
Am 2014-07-16 08:43, schrieb Stefan Agner:
Quoted 38 lines
Am 2014-07-15 16:24, schrieb Marc Kleine-Budde:
<snip>
Quoted 21 lines
Quoted 9 lines
(quoted diff) +0 -5
@@ -150,18 +171,20 @@
  * FLEXCAN hardware feature flags
  *
  * Below is some version info we got:
- *    SOC   Version   IP-Version  Glitch-  [TR]WRN_INT
- *                                Filter?   connected?
- *   MX25  FlexCAN2  03.00.00.00     no         no
- *   MX28  FlexCAN2  03.00.04.00    yes        yes
- *   MX35  FlexCAN2  03.00.00.00     no         no
Review line 181
Quoted 10 lines
(quoted diff) +8 -2
- *   MX53  FlexCAN2  03.00.00.00    yes         no
- *   MX6s  FlexCAN3  10.00.12.00    yes        yes
+ *    SOC   Version   IP-Version  Glitch-  [TR]WRN_INT  Memory err
+ *                                Filter?   connected?  detection
+ *   MX25  FlexCAN2  03.00.00.00     no         no         no
+ *   MX28  FlexCAN2  03.00.04.00    yes        yes         no
+ *   MX35  FlexCAN2  03.00.00.00     no         no         no
+ *   MX53  FlexCAN2  03.00.00.00    yes         no         no
+ *   MX6s  FlexCAN3  10.00.12.00    yes        yes         no
+ *   VF610 FlexCAN3  ?               no         no        yes
                                        ^^         ^^
Quoted 2 lines
Can you check the datasheet if the flexcan core has a "Glitch Filter Width Register (FLEXCANx_GFWR)"
There is no such register called GFWR/Glitch Filter or similar.
Quoted 3 lines
Can you check if the core generates a warning interrupt with the current setup, if you don't switch on bus error reporting? This means internally the [TR]WRN_INT is connected and works as specified.
Ok, so I disabled TWRNMSK (Bit 11) in the control register and printed out the error and status register (ESR1), this is what I get:
[  191.285295] flexcan_irq, esr=00040080
[  191.288996] flexcan_irq, ctrl=17092051

Quoted 8 lines

Quoted 4 lines
Quoted 2 lines
Bit 17 (TWRNINT) is not set while TWRNMSK is disabled. Hence [TR]WRN_INT is not connected?
Ping. Anything open/to do from my side?
Please keep the printing of esr and ctrl in the interrupt handler, add a #define DEBUG in the driver, but do not change anything else. Then:

Ok, my changes look like this:

drivers/net/can/flexcan.c +1 -0

index 1c31a5d..fe8b81c 100644
@@ -19,6 +19,7 @@
  *
  */
 
+#define DEBUG
 #include <linux/netdevice.h>
 #include <linux/can.h>
 #include <linux/can/dev.h>

@@ -743,6 +744,9 @@ static irqreturn_t flexcan_irq(int irq, void

*dev_id)

        reg_iflag1 = flexcan_read(&regs->iflag1);
        reg_esr = flexcan_read(&regs->esr);

         */
        reg_ctrl = flexcan_read(&regs->ctrl);
        reg_ctrl &= ~FLEXCAN_CTRL_TSYN;

I'm not sure whether you really want to keep the FLEXCAN_CTRL_ERR_STATE commented out...

Quoted 8 lines

start the driver as usual:
- configure bitrate
- ifconfig can0 up
- _do_not_ enable bit error reporint
- start candump from gitorious with:
candump -e any,0:0,#FFFFFFFF
- short circuit CAN-High and CAN-Low
- send a CAN frame

root@colibri-vf:~# ip link set can0 type can bitrate 500000
[  146.140862] flexcan 40020000.flexcan can0: bitrate error 0.7%
root@colibri-vf:~# ip link set can0 up
[  146.661430] flexcan 40020000.flexcan can0: writing ctrl=0x17092001
[  146.667902] flexcan 40020000.flexcan can0: flexcan_set_bittiming:
mcr=0x5980000f ctrl=0x17092001
[  146.676790] flexcan 40020000.flexcan can0: flexcan_chip_start:
writing mcr=0x79a20208
[  146.684709] flexcan 40020000.flexcan can0: flexcan_chip_start:
writing ctrl=0x17092051
[  146.698228] flexcan 40020000.flexcan can0: flexcan_chip_start:
reading mcr=0x60a20208 ctrl=0x1709205

# cansend can0 1F334455#1122334455667788
interface = can0, family = 29, type = 3, proto =

Nothing happens on candump.

Quoted 5 lines

Another test is to setup a proper CAN bus, but configure the a second CAN node with a different bitrate. Start the can0 on vf610 as usual, then candump -e any,0:0,#FFFFFFFF, but do not send any CAN frames on the vf610. Then on the other system keep sending CAN frames, you might have to restart the CAN on the second system....

I'm using a PCAN-USB from Peak System for this test. When running with the same bitrates on both sides (500000, things work smoothly as expected:

# ip link set can0 type can bitrate 500000
# ip link set can0 up
# cansend can0 1F334455#1122334455667788

root@colibri-vf:~# ./candump -e any,0:0,#FFFFFFFF
  can0  1F334455   [8]  11 22 33 44 55 66 77 88

dmesg:

[  541.772502] flexcan_irq, esr=00040180
[  541.776207] flexcan_irq, ctrl=17092051

Then I reconfigure the system on my host:

# ip link set can0 down
# ip link set can0 type can bitrate 1000000
# ip link set can0 up
# cansend can0 1F334455#1122334455667788

Nothing happens on Vybrid side.

However, I got once this Kernel panic after I reconfigured to normal mode. But I could not reproduce this.

[  461.954394] flexcan_irq, esr=00059d82
[  461.958093] flexcan_irq, ctrl=17092051
[  461.961873] ------------[ cut here ]------------
[  461.966536] WARNING: CPU: 0 PID: 0 at kernel/locking/mutex.c:826
mutex_trylock+0x1b0/0x208()
[  461.974982] DEBUG_LOCKS_WARN_ON(in_interrupt())
[  461.979347] Modules linked in:
[  461.982621] CPU: 0 PID: 0 Comm: swapper/0 Not tainted
3.16.0-rc4-00017-ge9a974f-dirty #215
[  461.990896] Backtrace:
[  461.993412] [<80011e1c>] (dump_backtrace) from [<80011fb8>]
(show_stack+0x18/0x1c)
[  462.000991]  r6:806718ec r5:00000000 r4:00000000 r3:00000000
[  462.006836] [<80011fa0>] (show_stack) from [<8066e160>]
(dump_stack+0x88/0xa4)
[  462.014143] [<8066e0d8>] (dump_stack) from [<80028f48>]
(warn_slowpath_common+0x70/0x94)
[  462.022280]  r5:00000009 r4:808f9d50
[  462.025920] [<80028ed8>] (warn_slowpath_common) from [<80029010>]
(warn_slowpath_fmt+0x38/0x40)
[  462.034666]  r8:808f9e14 r7:8110cf7c r6:804c2fa0 r5:8e9ee000
r4:8094cdcc
[  462.041478] [<80028fdc>] (warn_slowpath_fmt) from [<806718ec>]
(mutex_trylock+0x1b0/0x208)
[  462.049792]  r3:807e3f6c r2:807e1b8c
[  462.053466] [<8067173c>] (mutex_trylock) from [<804c2fa0>]
(clk_prepare_lock+0x14/0xec)
[  462.061479]  r7:90880000 r6:8e81f800 r5:8e9ee000 r4:8e81f800
[  462.067280] [<804c2f8c>] (clk_prepare_lock) from [<804c50d0>]
(clk_prepare+0x14/0x2c)
[  462.075158]  r6:8e81f800 r5:8e9ee000 r4:8e81f800 r3:00000000
[  462.080918] [<804c50bc>] (clk_prepare) from [<803e7a50>]
(flexcan_get_berr_counter+0x24/0xd0)
[  462.089487]  r4:00000001 r3:00000000
[  462.093156] [<803e7a2c>] (flexcan_get_berr_counter) from [<803e895c>]
(flexcan_poll+0x40c/0x58c)
[  462.101992]  r8:0000000a r7:0000000a r6:8e372388 r5:8e172a80
r4:00000001 r3:00000000
[  462.109843] [<803e8550>] (flexcan_poll) from [<80511f90>]
(net_rx_action+0xcc/0x1b4)
[  462.117630]  r10:8e9ee6c0 r9:00000003 r8:0000000a r7:8fdde188
r6:808fa0c0 r5:8fdde180
[  462.125587]  r4:0000012c
[  462.128164] [<80511ec4>] (net_rx_action) from [<8002d290>]
(__do_softirq+0x120/0x26c)
[  462.136038]  r10:808fa080 r9:00000003 r8:00000100 r7:00000003
r6:808f8000 r5:808fa08c
[  462.143994]  r4:00000000
[  462.146566] [<8002d170>] (__do_softirq) from [<8002d6d4>]
(irq_exit+0xb0/0x104)
[  462.153923]  r10:806788ac r9:808f8000 r8:00000000 r7:0000005a
r6:808f8000 r5:808f5e2c
[  462.161877]  r4:808f8000
[  462.164459] [<8002d624>] (irq_exit) from [<8000f4bc>]
(handle_IRQ+0x58/0xb8)
[  462.171520]  r4:80900d2c r3:000000a0
[  462.175200] [<8000f464>] (handle_IRQ) from [<800086c0>]
(gic_handle_irq+0x30/0x68)
[  462.182818]  r8:8095c587 r7:90802100 r6:808f9f28 r5:80900ea0
r4:9080210c r3:000000a0
[  462.190671] [<80008690>] (gic_handle_irq) from [<80012ae4>]
(__irq_svc+0x44/0x5c)
[  462.198203] Exception stack(0x808f9f28 to 0x808f9f70)
[  462.203315] 9f20:                   00000001 00000001 00000000
80904070 8090098c 80900938
[  462.211517] 9f40: 8095c587 00000000 8095c587 808f8000 806788ac
808f9f7c 808f9f40 808f9f70
[  462.219746] 9f60: 80066a98 8000f834 20000013 ffffffff
[  462.224852]  r7:808f9f5c r6:ffffffff r5:20000013 r4:8000f834
[  462.230621] [<8000f80c>] (arch_cpu_idle) from [<8005fba4>]
(cpu_startup_entry+0x104/0x16c)
[  462.238964] [<8005faa0>] (cpu_startup_entry) from [<80668cf8>]
(rest_init+0xb0/0xd8)
[  462.246757]  r7:8ffffcc0 r3:00000000
[  462.250419] [<80668c48>] (rest_init) from [<808a5bf8>]
(start_kernel+0x340/0x3ac)
[  462.257979]  r5:8095c7c0 r4:80900a38
[  462.261620] [<808a58b8>] (start_kernel) from [<80008074>]
(0x80008074)
[  462.268204] ---[ end trace c9c9dee0ce2272a7 ]---
[  462.272899] flexcan 40020000.flexcan can0: Error Warning IRQ

candump showed this:
can0 20000004 [8] 00 04 00 00 00 00 00 00 ERRORFRAME

	controller-problem{rx-error-warning}

Quoted 4 lines

Please send the outputs of candump and demsg to the list. It should generate a warning, error passive and finally a busoff message.

--
Stefan

Marc Kleine-Budde

maintainer

2014-07-15 13:54 UTC #24 lore raw

In reply to Stefan Agner

Quoted 19 lines · Stefan Agner

This series adds support for Vybrid (aka vf610) to the FlexCAN controller and extends the device tree accordingly.
Changes in v3:
- Return error number in flexcan_get_berr_counter if clock enabling fails
- Add the FLEXCANX_EN clocks as new clocks
Changes in v2:
- Split out patch (seperate dt, clocks and driver changes)
- Use spaces for hardware feature flags table
- Remove drive-by change of esdhc register length
- Added related fix which enables clock in berr_counter
Stefan Agner (4):
ARM: dts: vf610: add FlexCAN node
ARM: imx: clk-vf610: fix FlexCAN clock gating
can: flexcan: switch on clocks before accessing ecr register
can: flexcan: add vf610 support for FlexCAN

Quoted 5 lines

 arch/arm/boot/dts/vf610.dtsi            | 23 +++++++++
 arch/arm/mach-imx/clk-vf610.c           |  6 ++-
 drivers/net/can/flexcan.c               | 91 +++++++++++++++++++++++++++++----
 include/dt-bindings/clock/vf610-clock.h |  4 +-
 4 files changed, 110 insertions(+), 14 deletions(-)

I'm taking patch 3+4 via the linux-can-next tree.

Thanks,
Marc

Signature · 12 lines

Pengutronix e.K.                  | Marc Kleine-Budde           |
Industrial Linux Solutions        | Phone: +49-231-2826-924     |
Vertretung West/Dortmund          | Fax:   +49-5121-206917-5555 |
Amtsgericht Hildesheim, HRA 2686  | http://www.pengutronix.de   |

-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 242 bytes
Desc: OpenPGP digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20140715/95a7776f/attachment.sig>

Marc Kleine-Budde

maintainer Applied

2014-08-14 10:04 UTC #25 lore raw

Quoted 20 lines · Marc Kleine-Budde

Quoted 19 lines · Stefan Agner
This series adds support for Vybrid (aka vf610) to the FlexCAN controller and extends the device tree accordingly.
Changes in v3:
- Return error number in flexcan_get_berr_counter if clock enabling fails
- Add the FLEXCANX_EN clocks as new clocks
Changes in v2:
- Split out patch (seperate dt, clocks and driver changes)
- Use spaces for hardware feature flags table
- Remove drive-by change of esdhc register length
- Added related fix which enables clock in berr_counter
Stefan Agner (4):
ARM: dts: vf610: add FlexCAN node
ARM: imx: clk-vf610: fix FlexCAN clock gating
can: flexcan: switch on clocks before accessing ecr register
can: flexcan: add vf610 support for FlexCAN

Quoted 7 lines

Quoted 5 lines

 arch/arm/boot/dts/vf610.dtsi            | 23 +++++++++
 arch/arm/mach-imx/clk-vf610.c           |  6 ++-
 drivers/net/can/flexcan.c               | 91 +++++++++++++++++++++++++++++----
 include/dt-bindings/clock/vf610-clock.h |  4 +-
 4 files changed, 110 insertions(+), 14 deletions(-)

I'm taking patch 3+4 via the linux-can-next tree.

Applied to linux-can-next, with the modified version of the 3/4.

Thanks,
Marc

Signature · 12 lines

Pengutronix e.K.                  | Marc Kleine-Budde           |
Industrial Linux Solutions        | Phone: +49-231-2826-924     |
Vertretung West/Dortmund          | Fax:   +49-5121-206917-5555 |
Amtsgericht Hildesheim, HRA 2686  | http://www.pengutronix.de   |

-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 181 bytes
Desc: OpenPGP digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20140814/f104fc15/attachment.sig>

Shawn Guo

Applied

2014-07-16 06:11 UTC #26 lore raw

In reply to Stefan Agner

Quoted 3 lines · Stefan Agner

Stefan Agner (4):
ARM: dts: vf610: add FlexCAN node
ARM: imx: clk-vf610: fix FlexCAN clock gating

Applied these two, thanks.

Quoted 2 lines

can: flexcan: switch on clocks before accessing ecr register
can: flexcan: add vf610 support for FlexCAN