ARM: i.MX: Remove mach-cpuimx27sd board file

eukrea_mbimx27-baseboard.c and mach-cpuimx27.c can be replaced with their devicetree equivalents: imx27-eukrea-mbimxsd27-baseboard.dts and imx27-eukrea-cpuimx27.dtsi respectively, so remove the board files.

Signed-off-by Alexander Shiyan <[email protected]>

---
 arch/arm/configs/imx_v4_v5_defconfig         |   3 -
 arch/arm/mach-imx/Kconfig                    |  50 ----
 arch/arm/mach-imx/Makefile                   |   2 -
 arch/arm/mach-imx/eukrea-baseboards.h        |  10 +-
 arch/arm/mach-imx/eukrea_mbimx27-baseboard.c | 351 ---------------------------
 arch/arm/mach-imx/mach-cpuimx27.c            | 321 ------------------------
 6 files changed, 1 insertion(+), 736 deletions(-)
 delete mode 100644 arch/arm/mach-imx/eukrea_mbimx27-baseboard.c
 delete mode 100644 arch/arm/mach-imx/mach-cpuimx27.c

arch/arm/configs/imx_v4_v5_defconfig +0 -3

index 63bde0e..f53074c 100644
@@ -31,9 +31,6 @@ CONFIG_MACH_EUKREA_CPUIMX25SD=y
 CONFIG_MACH_IMX25_DT=y
 CONFIG_MACH_MX27ADS=y
 CONFIG_MACH_PCM038=y
-CONFIG_MACH_CPUIMX27=y
-CONFIG_MACH_EUKREA_CPUIMX27_USESDHC2=y
-CONFIG_MACH_EUKREA_CPUIMX27_USEUART4=y
 CONFIG_MACH_MX27_3DS=y
 CONFIG_MACH_IMX27_VISSTRIM_M10=y
 CONFIG_MACH_PCA100=y

arch/arm/mach-imx/Kconfig +0 -50

index c6810b8..901e9ab 100644
@@ -263,56 +263,6 @@ config MACH_PCM970_BASEBOARD
 
 endchoice
 
-config MACH_CPUIMX27
-	bool "Eukrea CPUIMX27 module"
-	select IMX_HAVE_PLATFORM_FSL_USB2_UDC
-	select IMX_HAVE_PLATFORM_IMX2_WDT
-	select IMX_HAVE_PLATFORM_IMX_I2C
-	select IMX_HAVE_PLATFORM_IMX_UART
-	select IMX_HAVE_PLATFORM_MXC_EHCI
-	select IMX_HAVE_PLATFORM_MXC_NAND
-	select IMX_HAVE_PLATFORM_MXC_W1
-	select USB_ULPI_VIEWPORT if USB_ULPI
-	select SOC_IMX27
-	help
-	  Include support for Eukrea CPUIMX27 platform. This includes
-	  specific configurations for the module and its peripherals.
-
-config MACH_EUKREA_CPUIMX27_USESDHC2
-	bool "CPUIMX27 integrates SDHC2 module"
-	depends on MACH_CPUIMX27
-	select IMX_HAVE_PLATFORM_MXC_MMC
-	help
-	  This adds support for the internal SDHC2 used on CPUIMX27
-	  for wifi or eMMC.
-
-config MACH_EUKREA_CPUIMX27_USEUART4
-	bool "CPUIMX27 integrates UART4 module"
-	depends on MACH_CPUIMX27
-	help
-	  This adds support for the internal UART4 used on CPUIMX27
-	  for bluetooth.
-
-choice
-	prompt "Baseboard"
-	depends on MACH_CPUIMX27
-	default MACH_EUKREA_MBIMX27_BASEBOARD
-
-config MACH_EUKREA_MBIMX27_BASEBOARD
-	bool "Eukrea MBIMX27 development board"
-	select IMX_HAVE_PLATFORM_IMX_FB
-	select IMX_HAVE_PLATFORM_IMX_KEYPAD
-	select IMX_HAVE_PLATFORM_IMX_SSI
-	select IMX_HAVE_PLATFORM_IMX_UART
-	select IMX_HAVE_PLATFORM_MXC_MMC
-	select IMX_HAVE_PLATFORM_SPI_IMX
-	select LEDS_GPIO_REGISTER
-	help
-	  This adds board specific devices that can be found on Eukrea's
-	  MBIMX27 evaluation board.
-
-endchoice
-
 config MACH_MX27_3DS
 	bool "MX27PDK platform"
 	select IMX_HAVE_PLATFORM_FSL_USB2_UDC

arch/arm/mach-imx/Makefile +0 -2

index 2783d27..2942ec3 100644
@@ -61,8 +61,6 @@ obj-$(CONFIG_MACH_PCM038) += mach-pcm038.o
 obj-$(CONFIG_MACH_PCM970_BASEBOARD) += pcm970-baseboard.o
 obj-$(CONFIG_MACH_MX27_3DS) += mach-mx27_3ds.o
 obj-$(CONFIG_MACH_IMX27_VISSTRIM_M10) += mach-imx27_visstrim_m10.o
-obj-$(CONFIG_MACH_CPUIMX27) += mach-cpuimx27.o
-obj-$(CONFIG_MACH_EUKREA_MBIMX27_BASEBOARD) += eukrea_mbimx27-baseboard.o
 obj-$(CONFIG_MACH_PCA100) += mach-pca100.o
 obj-$(CONFIG_MACH_MXT_TD60) += mach-mxt_td60.o
 obj-$(CONFIG_MACH_IMX27_DT) += imx27-dt.o

arch/arm/mach-imx/eukrea-baseboards.h +1 -9

index a21d331..bb2c90d 100644
@@ -27,23 +27,15 @@
  * This CPU module needs a baseboard to work. After basic initializing
  * its own devices, it calls baseboard's init function.
  * TODO: Add your own baseboard init function and call it from
- * inside eukrea_cpuimx25_init() eukrea_cpuimx27_init()
- * eukrea_cpuimx35_init() eukrea_cpuimx51_init()
- * or eukrea_cpuimx51sd_init().
+ * inside eukrea_cpuimx25_init() or eukrea_cpuimx35_init()
  *
  * This example here is for the development board. Refer
  * mach-mx25/eukrea_mbimxsd-baseboard.c for cpuimx25
- * mach-imx/eukrea_mbimx27-baseboard.c for cpuimx27
  * mach-mx3/eukrea_mbimxsd-baseboard.c for cpuimx35
- * mach-mx5/eukrea_mbimx51-baseboard.c for cpuimx51
- * mach-mx5/eukrea_mbimxsd-baseboard.c for cpuimx51sd
  */
 
 extern void eukrea_mbimxsd25_baseboard_init(void);
-extern void eukrea_mbimx27_baseboard_init(void);
 extern void eukrea_mbimxsd35_baseboard_init(void);
-extern void eukrea_mbimx51_baseboard_init(void);
-extern void eukrea_mbimxsd51_baseboard_init(void);
 
 #endif
 

arch/arm/mach-imx/eukrea_mbimx27-baseboard.c deleted +0 -351

deleted file mode 100644
index b2f08bf..0000000
@@ -1,351 +0,0 @@
-/*
- * Copyright (C) 2009-2010 Eric Benard - eric at eukrea.com
- *
- * Based on pcm970-baseboard.c which is :
- * Copyright (C) 2008 Juergen Beisert (kernel at pengutronix.de)
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License
- * as published by the Free Software Foundation; either version 2
- * of the License, or (at your option) any later version.
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
- * MA 02110-1301, USA.
- */
-
-#include <linux/gpio.h>
-#include <linux/irq.h>
-#include <linux/platform_device.h>
-#include <linux/spi/spi.h>
-#include <linux/spi/ads7846.h>
-#include <linux/backlight.h>
-#include <video/platform_lcd.h>
-
-#include <asm/mach/arch.h>
-
-#include "common.h"
-#include "devices-imx27.h"
-#include "hardware.h"
-#include "iomux-mx27.h"
-
-static const int eukrea_mbimx27_pins[] __initconst = {
-	/* UART2 */
-	PE3_PF_UART2_CTS,
-	PE4_PF_UART2_RTS,
-	PE6_PF_UART2_TXD,
-	PE7_PF_UART2_RXD,
-	/* UART3 */
-	PE8_PF_UART3_TXD,
-	PE9_PF_UART3_RXD,
-	PE10_PF_UART3_CTS,
-	PE11_PF_UART3_RTS,
-	/* UART4 */
-#if !defined(CONFIG_MACH_EUKREA_CPUIMX27_USEUART4)
-	PB26_AF_UART4_RTS,
-	PB28_AF_UART4_TXD,
-	PB29_AF_UART4_CTS,
-	PB31_AF_UART4_RXD,
-#endif
-	/* SDHC1*/
-	PE18_PF_SD1_D0,
-	PE19_PF_SD1_D1,
-	PE20_PF_SD1_D2,
-	PE21_PF_SD1_D3,
-	PE22_PF_SD1_CMD,
-	PE23_PF_SD1_CLK,
-	/* display */
-	PA5_PF_LSCLK,
-	PA6_PF_LD0,
-	PA7_PF_LD1,
-	PA8_PF_LD2,
-	PA9_PF_LD3,
-	PA10_PF_LD4,
-	PA11_PF_LD5,
-	PA12_PF_LD6,
-	PA13_PF_LD7,
-	PA14_PF_LD8,
-	PA15_PF_LD9,
-	PA16_PF_LD10,
-	PA17_PF_LD11,
-	PA18_PF_LD12,
-	PA19_PF_LD13,
-	PA20_PF_LD14,
-	PA21_PF_LD15,
-	PA22_PF_LD16,
-	PA23_PF_LD17,
-	PA28_PF_HSYNC,
-	PA29_PF_VSYNC,
-	PA30_PF_CONTRAST,
-	PA31_PF_OE_ACD,
-	/* SPI1 */
-	PD29_PF_CSPI1_SCLK,
-	PD30_PF_CSPI1_MISO,
-	PD31_PF_CSPI1_MOSI,
-	/* SSI4 */
-#if defined(CONFIG_SND_SOC_EUKREA_TLV320) \
-	|| defined(CONFIG_SND_SOC_EUKREA_TLV320_MODULE)
-	PC16_PF_SSI4_FS,
-	PC17_PF_SSI4_RXD | GPIO_PUEN,
-	PC18_PF_SSI4_TXD | GPIO_PUEN,
-	PC19_PF_SSI4_CLK,
-#endif
-};
-
-static const uint32_t eukrea_mbimx27_keymap[] = {
-	KEY(0, 0, KEY_UP),
-	KEY(0, 1, KEY_DOWN),
-	KEY(1, 0, KEY_RIGHT),
-	KEY(1, 1, KEY_LEFT),
-};
-
-static const struct matrix_keymap_data
-eukrea_mbimx27_keymap_data __initconst = {
-	.keymap         = eukrea_mbimx27_keymap,
-	.keymap_size    = ARRAY_SIZE(eukrea_mbimx27_keymap),
-};
-
-static const struct gpio_led eukrea_mbimx27_gpio_leds[] __initconst = {
-	{
-		.name			= "led1",
-		.default_trigger	= "heartbeat",
-		.active_low		= 1,
-		.gpio			= GPIO_PORTF | 16,
-	},
-	{
-		.name			= "led2",
-		.default_trigger	= "none",
-		.active_low		= 1,
-		.gpio			= GPIO_PORTF | 19,
-	},
-};
-
-static const struct gpio_led_platform_data
-		eukrea_mbimx27_gpio_led_info __initconst = {
-	.leds		= eukrea_mbimx27_gpio_leds,
-	.num_leds	= ARRAY_SIZE(eukrea_mbimx27_gpio_leds),
-};
-
-static struct imx_fb_videomode eukrea_mbimx27_modes[] = {
-	{
-		.mode = {
-			.name		= "CMO-QVGA",
-			.refresh	= 60,
-			.xres		= 320,
-			.yres		= 240,
-			.pixclock	= 156000,
-			.hsync_len	= 30,
-			.left_margin	= 38,
-			.right_margin	= 20,
-			.vsync_len	= 3,
-			.upper_margin	= 15,
-			.lower_margin	= 4,
-		},
-		.pcr		= 0xFAD08B80,
-		.bpp		= 16,
-	}, {
-		.mode = {
-			.name		= "DVI-VGA",
-			.refresh	= 60,
-			.xres		= 640,
-			.yres		= 480,
-			.pixclock	= 32000,
-			.hsync_len	= 1,
-			.left_margin	= 35,
-			.right_margin	= 0,
-			.vsync_len	= 1,
-			.upper_margin	= 7,
-			.lower_margin	= 0,
-		},
-		.pcr		= 0xFA208B80,
-		.bpp		= 16,
-	}, {
-		.mode = {
-			.name		= "DVI-SVGA",
-			.refresh	= 60,
-			.xres		= 800,
-			.yres		= 600,
-			.pixclock	= 25000,
-			.hsync_len	= 1,
-			.left_margin	= 35,
-			.right_margin	= 0,
-			.vsync_len	= 1,
-			.upper_margin	= 7,
-			.lower_margin	= 0,
-		},
-		.pcr		= 0xFA208B80,
-		.bpp		= 16,
-	},
-};
-
-static const struct imx_fb_platform_data eukrea_mbimx27_fb_data __initconst = {
-	.mode = eukrea_mbimx27_modes,
-	.num_modes = ARRAY_SIZE(eukrea_mbimx27_modes),
-
-	.pwmr		= 0x00A903FF,
-	.lscr1		= 0x00120300,
-	.dmacr		= 0x00040060,
-};
-
-static void eukrea_mbimx27_bl_set_intensity(int intensity)
-{
-	if (intensity)
-		gpio_direction_output(GPIO_PORTE | 5, 1);
-	else
-		gpio_direction_output(GPIO_PORTE | 5, 0);
-}
-
-static struct generic_bl_info eukrea_mbimx27_bl_info = {
-	.name			= "eukrea_mbimx27-bl",
-	.max_intensity		= 0xff,
-	.default_intensity	= 0xff,
-	.set_bl_intensity	= eukrea_mbimx27_bl_set_intensity,
-};
-
-static struct platform_device eukrea_mbimx27_bl_dev = {
-	.name			= "generic-bl",
-	.id			= 1,
-	.dev = {
-		.platform_data	= &eukrea_mbimx27_bl_info,
-	},
-};
-
-static void eukrea_mbimx27_lcd_power_set(struct plat_lcd_data *pd,
-				   unsigned int power)
-{
-	if (power)
-		gpio_direction_output(GPIO_PORTA | 25, 1);
-	else
-		gpio_direction_output(GPIO_PORTA | 25, 0);
-}
-
-static struct plat_lcd_data eukrea_mbimx27_lcd_power_data = {
-	.set_power		= eukrea_mbimx27_lcd_power_set,
-};
-
-static struct platform_device eukrea_mbimx27_lcd_powerdev = {
-	.name			= "platform-lcd",
-	.dev.platform_data	= &eukrea_mbimx27_lcd_power_data,
-};
-
-static const struct imxuart_platform_data uart_pdata __initconst = {
-	.flags = IMXUART_HAVE_RTSCTS,
-};
-
-#define ADS7846_PENDOWN (GPIO_PORTD | 25)
-
-static void __maybe_unused ads7846_dev_init(void)
-{
-	if (gpio_request(ADS7846_PENDOWN, "ADS7846 pendown") < 0) {
-		printk(KERN_ERR "can't get ads7846 pen down GPIO\n");
-		return;
-	}
-	gpio_direction_input(ADS7846_PENDOWN);
-}
-
-static int ads7846_get_pendown_state(void)
-{
-	return !gpio_get_value(ADS7846_PENDOWN);
-}
-
-static struct ads7846_platform_data ads7846_config __initdata = {
-	.get_pendown_state	= ads7846_get_pendown_state,
-	.keep_vref_on		= 1,
-};
-
-static struct spi_board_info __maybe_unused
-		eukrea_mbimx27_spi_board_info[] __initdata = {
-	[0] = {
-		.modalias	= "ads7846",
-		.bus_num	= 0,
-		.chip_select	= 0,
-		.max_speed_hz	= 1500000,
-		/* irq number is run-time assigned */
-		.platform_data	= &ads7846_config,
-		.mode           = SPI_MODE_2,
-	},
-};
-
-static int eukrea_mbimx27_spi_cs[] = {GPIO_PORTD | 28};
-
-static const struct spi_imx_master eukrea_mbimx27_spi0_data __initconst = {
-	.chipselect	= eukrea_mbimx27_spi_cs,
-	.num_chipselect = ARRAY_SIZE(eukrea_mbimx27_spi_cs),
-};
-
-static struct i2c_board_info eukrea_mbimx27_i2c_devices[] = {
-	{
-		I2C_BOARD_INFO("tlv320aic23", 0x1a),
-	},
-};
-
-static const struct imxmmc_platform_data sdhc_pdata __initconst = {
-	.dat3_card_detect = 1,
-};
-
-static const
-struct imx_ssi_platform_data eukrea_mbimx27_ssi_pdata __initconst = {
-	.flags = IMX_SSI_DMA | IMX_SSI_USE_I2S_SLAVE,
-};
-
-/*
- * system init for baseboard usage. Will be called by cpuimx27 init.
- *
- * Add platform devices present on this baseboard and init
- * them from CPU side as far as required to use them later on
- */
-void __init eukrea_mbimx27_baseboard_init(void)
-{
-	mxc_gpio_setup_multiple_pins(eukrea_mbimx27_pins,
-		ARRAY_SIZE(eukrea_mbimx27_pins), "MBIMX27");
-
-	imx27_add_imx_uart1(&uart_pdata);
-	imx27_add_imx_uart2(&uart_pdata);
-#if !defined(CONFIG_MACH_EUKREA_CPUIMX27_USEUART4)
-	imx27_add_imx_uart3(&uart_pdata);
-#endif
-
-	imx27_add_imx_fb(&eukrea_mbimx27_fb_data);
-	imx27_add_mxc_mmc(0, &sdhc_pdata);
-
-	i2c_register_board_info(0, eukrea_mbimx27_i2c_devices,
-				ARRAY_SIZE(eukrea_mbimx27_i2c_devices));
-
-	imx27_add_imx_ssi(0, &eukrea_mbimx27_ssi_pdata);
-
-#if defined(CONFIG_TOUCHSCREEN_ADS7846) \
-	|| defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE)
-	/* ADS7846 Touchscreen controller init */
-	mxc_gpio_mode(GPIO_PORTD | 25 | GPIO_GPIO | GPIO_IN);
-	ads7846_dev_init();
-#endif
-
-	/* SPI_CS0 init */
-	mxc_gpio_mode(GPIO_PORTD | 28 | GPIO_GPIO | GPIO_OUT);
-	imx27_add_spi_imx0(&eukrea_mbimx27_spi0_data);
-	eukrea_mbimx27_spi_board_info[0].irq = gpio_to_irq(IMX_GPIO_NR(4, 25));
-	spi_register_board_info(eukrea_mbimx27_spi_board_info,
-			ARRAY_SIZE(eukrea_mbimx27_spi_board_info));
-
-	/* Leds configuration */
-	mxc_gpio_mode(GPIO_PORTF | 16 | GPIO_GPIO | GPIO_OUT);
-	mxc_gpio_mode(GPIO_PORTF | 19 | GPIO_GPIO | GPIO_OUT);
-	/* Backlight */
-	mxc_gpio_mode(GPIO_PORTE | 5 | GPIO_GPIO | GPIO_OUT);
-	gpio_request(GPIO_PORTE | 5, "backlight");
-	platform_device_register(&eukrea_mbimx27_bl_dev);
-	/* LCD Reset */
-	mxc_gpio_mode(GPIO_PORTA | 25 | GPIO_GPIO | GPIO_OUT);
-	gpio_request(GPIO_PORTA | 25, "lcd_enable");
-	platform_device_register(&eukrea_mbimx27_lcd_powerdev);
-
-	imx27_add_imx_keypad(&eukrea_mbimx27_keymap_data);
-
-	gpio_led_register_device(-1, &eukrea_mbimx27_gpio_led_info);
-	imx_add_platform_device("eukrea_tlv320", 0, NULL, 0, NULL, 0);
-}

arch/arm/mach-imx/mach-cpuimx27.c deleted +0 -321

deleted file mode 100644
index e6d4b99..0000000
@@ -1,321 +0,0 @@
-/*
- * Copyright (C) 2009 Eric Benard - eric at eukrea.com
- *
- * Based on pcm038.c which is :
- * Copyright 2007 Robert Schwebel <[email protected]>, Pengutronix
- * Copyright (C) 2008 Juergen Beisert (kernel at pengutronix.de)
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License
- * as published by the Free Software Foundation; either version 2
- * of the License, or (at your option) any later version.
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
- * MA 02110-1301, USA.
- */
-
-#include <linux/i2c.h>
-#include <linux/io.h>
-#include <linux/mtd/plat-ram.h>
-#include <linux/mtd/physmap.h>
-#include <linux/platform_device.h>
-#include <linux/serial_8250.h>
-#include <linux/usb/otg.h>
-#include <linux/usb/ulpi.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/time.h>
-#include <asm/mach/map.h>
-
-#include "common.h"
-#include "devices-imx27.h"
-#include "ehci.h"
-#include "eukrea-baseboards.h"
-#include "hardware.h"
-#include "iomux-mx27.h"
-#include "ulpi.h"
-
-static const int eukrea_cpuimx27_pins[] __initconst = {
-	/* UART1 */
-	PE12_PF_UART1_TXD,
-	PE13_PF_UART1_RXD,
-	PE14_PF_UART1_CTS,
-	PE15_PF_UART1_RTS,
-	/* UART4 */
-#if defined(CONFIG_MACH_EUKREA_CPUIMX27_USEUART4)
-	PB26_AF_UART4_RTS,
-	PB28_AF_UART4_TXD,
-	PB29_AF_UART4_CTS,
-	PB31_AF_UART4_RXD,
-#endif
-	/* FEC */
-	PD0_AIN_FEC_TXD0,
-	PD1_AIN_FEC_TXD1,
-	PD2_AIN_FEC_TXD2,
-	PD3_AIN_FEC_TXD3,
-	PD4_AOUT_FEC_RX_ER,
-	PD5_AOUT_FEC_RXD1,
-	PD6_AOUT_FEC_RXD2,
-	PD7_AOUT_FEC_RXD3,
-	PD8_AF_FEC_MDIO,
-	PD9_AIN_FEC_MDC,
-	PD10_AOUT_FEC_CRS,
-	PD11_AOUT_FEC_TX_CLK,
-	PD12_AOUT_FEC_RXD0,
-	PD13_AOUT_FEC_RX_DV,
-	PD14_AOUT_FEC_RX_CLK,
-	PD15_AOUT_FEC_COL,
-	PD16_AIN_FEC_TX_ER,
-	PF23_AIN_FEC_TX_EN,
-	/* I2C1 */
-	PD17_PF_I2C_DATA,
-	PD18_PF_I2C_CLK,
-	/* SDHC2 */
-#if defined(CONFIG_MACH_EUKREA_CPUIMX27_USESDHC2)
-	PB4_PF_SD2_D0,
-	PB5_PF_SD2_D1,
-	PB6_PF_SD2_D2,
-	PB7_PF_SD2_D3,
-	PB8_PF_SD2_CMD,
-	PB9_PF_SD2_CLK,
-#endif
-#if defined(CONFIG_SERIAL_8250) || defined(CONFIG_SERIAL_8250_MODULE)
-	/* Quad UART's IRQ */
-	GPIO_PORTB | 22 | GPIO_GPIO | GPIO_IN,
-	GPIO_PORTB | 23 | GPIO_GPIO | GPIO_IN,
-	GPIO_PORTB | 27 | GPIO_GPIO | GPIO_IN,
-	GPIO_PORTB | 30 | GPIO_GPIO | GPIO_IN,
-#endif
-	/* OTG */
-	PC7_PF_USBOTG_DATA5,
-	PC8_PF_USBOTG_DATA6,
-	PC9_PF_USBOTG_DATA0,
-	PC10_PF_USBOTG_DATA2,
-	PC11_PF_USBOTG_DATA1,
-	PC12_PF_USBOTG_DATA4,
-	PC13_PF_USBOTG_DATA3,
-	PE0_PF_USBOTG_NXT,
-	PE1_PF_USBOTG_STP,
-	PE2_PF_USBOTG_DIR,
-	PE24_PF_USBOTG_CLK,
-	PE25_PF_USBOTG_DATA7,
-	/* USBH2 */
-	PA0_PF_USBH2_CLK,
-	PA1_PF_USBH2_DIR,
-	PA2_PF_USBH2_DATA7,
-	PA3_PF_USBH2_NXT,
-	PA4_PF_USBH2_STP,
-	PD19_AF_USBH2_DATA4,
-	PD20_AF_USBH2_DATA3,
-	PD21_AF_USBH2_DATA6,
-	PD22_AF_USBH2_DATA0,
-	PD23_AF_USBH2_DATA2,
-	PD24_AF_USBH2_DATA1,
-	PD26_AF_USBH2_DATA5,
-};
-
-static struct physmap_flash_data eukrea_cpuimx27_flash_data = {
-	.width = 2,
-};
-
-static struct resource eukrea_cpuimx27_flash_resource = {
-	.start = 0xc0000000,
-	.end   = 0xc3ffffff,
-	.flags = IORESOURCE_MEM,
-};
-
-static struct platform_device eukrea_cpuimx27_nor_mtd_device = {
-	.name = "physmap-flash",
-	.id = 0,
-	.dev = {
-		.platform_data = &eukrea_cpuimx27_flash_data,
-	},
-	.num_resources = 1,
-	.resource = &eukrea_cpuimx27_flash_resource,
-};
-
-static const struct imxuart_platform_data uart_pdata __initconst = {
-	.flags = IMXUART_HAVE_RTSCTS,
-};
-
-static const struct mxc_nand_platform_data
-cpuimx27_nand_board_info __initconst = {
-	.width = 1,
-	.hw_ecc = 1,
-};
-
-static struct platform_device *platform_devices[] __initdata = {
-	&eukrea_cpuimx27_nor_mtd_device,
-};
-
-static const struct imxi2c_platform_data cpuimx27_i2c1_data __initconst = {
-	.bitrate = 100000,
-};
-
-static struct i2c_board_info eukrea_cpuimx27_i2c_devices[] = {
-	{
-		I2C_BOARD_INFO("pcf8563", 0x51),
-	},
-};
-
-#if defined(CONFIG_SERIAL_8250) || defined(CONFIG_SERIAL_8250_MODULE)
-static struct plat_serial8250_port serial_platform_data[] = {
-	{
-		.mapbase = (unsigned long)(MX27_CS3_BASE_ADDR + 0x200000),
-		/* irq number is run-time assigned */
-		.uartclk = 14745600,
-		.regshift = 1,
-		.iotype = UPIO_MEM,
-		.flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST | UPF_IOREMAP,
-	}, {
-		.mapbase = (unsigned long)(MX27_CS3_BASE_ADDR + 0x400000),
-		/* irq number is run-time assigned */
-		.uartclk = 14745600,
-		.regshift = 1,
-		.iotype = UPIO_MEM,
-		.flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST | UPF_IOREMAP,
-	}, {
-		.mapbase = (unsigned long)(MX27_CS3_BASE_ADDR + 0x800000),
-		/* irq number is run-time assigned */
-		.uartclk = 14745600,
-		.regshift = 1,
-		.iotype = UPIO_MEM,
-		.flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST | UPF_IOREMAP,
-	}, {
-		.mapbase = (unsigned long)(MX27_CS3_BASE_ADDR + 0x1000000),
-		/* irq number is run-time assigned */
-		.uartclk = 14745600,
-		.regshift = 1,
-		.iotype = UPIO_MEM,
-		.flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST | UPF_IOREMAP,
-	}, {
-	}
-};
-
-static struct platform_device serial_device = {
-	.name = "serial8250",
-	.id = 0,
-	.dev = {
-		.platform_data = serial_platform_data,
-	},
-};
-#endif
-
-static int eukrea_cpuimx27_otg_init(struct platform_device *pdev)
-{
-	return mx27_initialize_usb_hw(pdev->id, MXC_EHCI_INTERFACE_DIFF_UNI);
-}
-
-static struct mxc_usbh_platform_data otg_pdata __initdata = {
-	.init	= eukrea_cpuimx27_otg_init,
-	.portsc	= MXC_EHCI_MODE_ULPI,
-};
-
-static int eukrea_cpuimx27_usbh2_init(struct platform_device *pdev)
-{
-	return mx27_initialize_usb_hw(pdev->id, MXC_EHCI_INTERFACE_DIFF_UNI);
-}
-
-static struct mxc_usbh_platform_data usbh2_pdata __initdata = {
-	.init	= eukrea_cpuimx27_usbh2_init,
-	.portsc	= MXC_EHCI_MODE_ULPI,
-};
-
-static const struct fsl_usb2_platform_data otg_device_pdata __initconst = {
-	.operating_mode = FSL_USB2_DR_DEVICE,
-	.phy_mode       = FSL_USB2_PHY_ULPI,
-};
-
-static bool otg_mode_host __initdata;
-
-static int __init eukrea_cpuimx27_otg_mode(char *options)
-{
-	if (!strcmp(options, "host"))
-		otg_mode_host = true;
-	else if (!strcmp(options, "device"))
-		otg_mode_host = false;
-	else
-		pr_info("otg_mode neither \"host\" nor \"device\". "
-			"Defaulting to device\n");
-	return 1;
-}
-__setup("otg_mode=", eukrea_cpuimx27_otg_mode);
-
-static void __init eukrea_cpuimx27_init(void)
-{
-	imx27_soc_init();
-
-	mxc_gpio_setup_multiple_pins(eukrea_cpuimx27_pins,
-		ARRAY_SIZE(eukrea_cpuimx27_pins), "CPUIMX27");
-
-	imx27_add_imx_uart0(&uart_pdata);
-
-	imx27_add_mxc_nand(&cpuimx27_nand_board_info);
-
-	i2c_register_board_info(0, eukrea_cpuimx27_i2c_devices,
-				ARRAY_SIZE(eukrea_cpuimx27_i2c_devices));
-
-	imx27_add_imx_i2c(0, &cpuimx27_i2c1_data);
-
-	imx27_add_fec(NULL);
-	platform_add_devices(platform_devices, ARRAY_SIZE(platform_devices));
-	imx27_add_imx2_wdt();
-	imx27_add_mxc_w1();
-
-#if defined(CONFIG_MACH_EUKREA_CPUIMX27_USESDHC2)
-	/* SDHC2 can be used for Wifi */
-	imx27_add_mxc_mmc(1, NULL);
-#endif
-#if defined(CONFIG_MACH_EUKREA_CPUIMX27_USEUART4)
-	/* in which case UART4 is also used for Bluetooth */
-	imx27_add_imx_uart3(&uart_pdata);
-#endif
-
-#if defined(CONFIG_SERIAL_8250) || defined(CONFIG_SERIAL_8250_MODULE)
-	serial_platform_data[0].irq = IMX_GPIO_NR(2, 23);
-	serial_platform_data[1].irq = IMX_GPIO_NR(2, 22);
-	serial_platform_data[2].irq = IMX_GPIO_NR(2, 27);
-	serial_platform_data[3].irq = IMX_GPIO_NR(2, 30);
-	platform_device_register(&serial_device);
-#endif
-
-	if (otg_mode_host) {
-		otg_pdata.otg = imx_otg_ulpi_create(ULPI_OTG_DRVVBUS |
-				ULPI_OTG_DRVVBUS_EXT);
-		if (otg_pdata.otg)
-			imx27_add_mxc_ehci_otg(&otg_pdata);
-	} else {
-		imx27_add_fsl_usb2_udc(&otg_device_pdata);
-	}
-
-	usbh2_pdata.otg = imx_otg_ulpi_create(ULPI_OTG_DRVVBUS |
-			ULPI_OTG_DRVVBUS_EXT);
-	if (usbh2_pdata.otg)
-		imx27_add_mxc_ehci_hs(2, &usbh2_pdata);
-
-#ifdef CONFIG_MACH_EUKREA_MBIMX27_BASEBOARD
-	eukrea_mbimx27_baseboard_init();
-#endif
-}
-
-static void __init eukrea_cpuimx27_timer_init(void)
-{
-	mx27_clocks_init(26000000);
-}
-
-MACHINE_START(EUKREA_CPUIMX27, "EUKREA CPUIMX27")
-	.atag_offset = 0x100,
-	.map_io = mx27_map_io,
-	.init_early = imx27_init_early,
-	.init_irq = mx27_init_irq,
-	.init_time	= eukrea_cpuimx27_timer_init,
-	.init_machine = eukrea_cpuimx27_init,
-	.restart	= mxc_restart,
-MACHINE_END

Le Sat, 26 Jul 2014 17:41:08 +0400,
Alexander Shiyan <[email protected]> a ?crit :

Quoted 1 line

Quoted 5 lines

eukrea_mbimx27-baseboard.c and mach-cpuimx27.c can be replaced with their devicetree equivalents: imx27-eukrea-mbimxsd27-baseboard.dts and imx27-eukrea-cpuimx27.dtsi respectively, so remove the board files.

Signed-off-by Alexander Shiyan <[email protected]>

Acked-by Eric B?nard <[email protected]>

Thanks !

Sat, 26 Jul 2014 20:20:42 +0200 ?? Eric B?nard <[email protected]>:

Quoted 8 lines

Le Sat, 26 Jul 2014 17:41:08 +0400,
Alexander Shiyan <[email protected]> a ?crit :

Quoted 5 lines

eukrea_mbimx27-baseboard.c and mach-cpuimx27.c can be replaced with their devicetree equivalents: imx27-eukrea-mbimxsd27-baseboard.dts and imx27-eukrea-cpuimx27.dtsi respectively, so remove the board files.

Quoted 4 lines

Quoted 1 line

Signed-off-by Alexander Shiyan <[email protected]>

Acked-by Eric B?nard <[email protected]>

Thanks !

Can I make a similar patch for Eukrea-i.MX25/35 boards?

eukrea_mbimx27-baseboard.c and mach-cpuimx27.c can be replaced with their devicetree equivalents: imx27-eukrea-mbimxsd27-baseboard.dts and imx27-eukrea-cpuimx27.dtsi respectively, so remove the board files.

Signed-off-by Alexander Shiyan <[email protected]>